enklined Posted June 3, 2011 Share Posted June 3, 2011 Built the following Sandy Bridge rig last night: Silverstone ML03B Micro ATX Case 4x ENERMAX UC-8EB 80mm 14 dBa Case Fans RAIDMAX HYBRID 2 RX-530SS 530W Modular PSU Intel Core i5-2400 3.1Ghz Quad-Core LGA 1155 CPU GIGABYTE GA-H67MA-UD2H-B3 2x G.SKILL Ripjaws 4GB 240-Pin DDR3 1333 RAM ASUS EN210 SILENT 1GB HDMI Video Card LITE-ON Black 4X Blu-Ray Drive Video is connected to EN210 VGA port. HDD is formatted as Mac OS Extended (Journaled) and is connected to SATA0 port (6GB/s) and DVD is connected to SATA1 (6GB/s) port. Only 1 4GB stick installed. Setup BIOS per [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url] Step One. Boot from [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url], swap in Retail SL 10.6.0 DVD, hit F5, and the Install Disc appears. Then, I hit enter, and the next screen is grey with Apple logo and spinning gear. It sits here for about 5 minutes, then goes to another grey screen and my mouse immediately turns into the spinning rainbow pinwheel of death. It sits like this for a minute or two, and the computer shuts off. To troubleshoot, this is what I've tried: Switched both HDD and DVD to be on SATA2 and SATA3 ports respectfully (3GB/s). On [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url] screen, tired both PCIRootUID=1, and PCIRootUID=1 -x, same result as stated above. Enabled 64-bit in BIOS, changed CPU multiplier to 29, changed SATA from IDE to ACHI, disabled EIST and C-States (For speedstep). Flashed Motherboard to F4 BIOS too. Used -v in [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url] after swapping in SL DVD. It constantly states "disk1s3: I/O error." Then loads some other things, saying it refused kext so using a different one, then boots to the 2nd grey screen with pinwheel of death, and shuts off a minute later. I am unsure how to proceed, and am at my wits end after spending hours troubleshooting. Any help would be greatly appreciated! Thanks! Link to comment https://www.insanelymac.com/forum/topic/258442-unable-to-install-on-new-gigabyte-ga-h67ma-ud2h-b3-i5-2400-htpc/ Share on other sites More sharing options...
step2008 Posted July 22, 2011 Share Posted July 22, 2011 Edit: I had the same problem, what I did was to disconnect the graphic card, and connect the monitor to the motherboard DVI connector for installation. I also previously restored (on a Mac) my SL DVD to a 8GB USB drive to be used as an installation disk. Link to comment https://www.insanelymac.com/forum/topic/258442-unable-to-install-on-new-gigabyte-ga-h67ma-ud2h-b3-i5-2400-htpc/#findComment-1719435 Share on other sites More sharing options...
jumper85 Posted October 14, 2011 Share Posted October 14, 2011 Built the following Sandy Bridge rig last night:Silverstone ML03B Micro ATX Case 4x ENERMAX UC-8EB 80mm 14 dBa Case Fans RAIDMAX HYBRID 2 RX-530SS 530W Modular PSU Intel Core i5-2400 3.1Ghz Quad-Core LGA 1155 CPU GIGABYTE GA-H67MA-UD2H-B3 2x G.SKILL Ripjaws 4GB 240-Pin DDR3 1333 RAM ASUS EN210 SILENT 1GB HDMI Video Card LITE-ON Black 4X Blu-Ray Drive Video is connected to EN210 VGA port. HDD is formatted as Mac OS Extended (Journaled) and is connected to SATA0 port (6GB/s) and DVD is connected to SATA1 (6GB/s) port. Only 1 4GB stick installed. Setup BIOS per [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url] Step One. Boot from [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url], swap in Retail SL 10.6.0 DVD, hit F5, and the Install Disc appears. Then, I hit enter, and the next screen is grey with Apple logo and spinning gear. It sits here for about 5 minutes, then goes to another grey screen and my mouse immediately turns into the spinning rainbow pinwheel of death. It sits like this for a minute or two, and the computer shuts off. To troubleshoot, this is what I've tried: Switched both HDD and DVD to be on SATA2 and SATA3 ports respectfully (3GB/s). On [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url] screen, tired both PCIRootUID=1, and PCIRootUID=1 -x, same result as stated above. Enabled 64-bit in BIOS, changed CPU multiplier to 29, changed SATA from IDE to ACHI, disabled EIST and C-States (For speedstep). Flashed Motherboard to F4 BIOS too. Used -v in [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url] after swapping in SL DVD. It constantly states "disk1s3: I/O error." Then loads some other things, saying it refused kext so using a different one, then boots to the 2nd grey screen with pinwheel of death, and shuts off a minute later. I am unsure how to proceed, and am at my wits end after spending hours troubleshooting. Any help would be greatly appreciated! Thanks! 1.Imposta il bios di default con HPET64 & AHCI abilitati 2.Come BOOT CD usa x64EmpireEFI (Legancy EmpireEFI for unsupported CPU) http://www.mediafire.com/?omahoyauvc1b1ka Link to comment https://www.insanelymac.com/forum/topic/258442-unable-to-install-on-new-gigabyte-ga-h67ma-ud2h-b3-i5-2400-htpc/#findComment-1759818 Share on other sites More sharing options...
PookyMacMan Posted October 15, 2011 Share Posted October 15, 2011 Sounds like your DVD is ruined. The other thing you can try is the OSx86 ModCD. I posted a link and guide here. Link to comment https://www.insanelymac.com/forum/topic/258442-unable-to-install-on-new-gigabyte-ga-h67ma-ud2h-b3-i5-2400-htpc/#findComment-1760221 Share on other sites More sharing options...
Recommended Posts