ddrmama Posted July 1, 2010 Share Posted July 1, 2010 Hi! I am going to install SL 10.6.4 in my PC. I have MB ASUS P7P55D LE, and I have 3 HDD: 2 SATA and 1 IDE. I did my BIOS changes: HDD in ACHI mode and JMicron in ACHI mode too. After of that I restarted with [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url] and when I insert the SL disk and push f5 the monitor crash (the tittle of the units). Then I take the SL disc and press install... the system restart in a few seconds and starts again.... What happend?? With EMPIRE EFI is the same problem... I don´t know what I can do. I have 2 partitions in each SATA HDD. ¿could be this the problem? Thanks PD. My graphic card is a ATI HD5670, and I know that is not supported by SL 10.6.4 but I would like to install unless my graphic card doesnt work 100% Link to comment Share on other sites More sharing options...
dima20202 Posted July 1, 2010 Share Posted July 1, 2010 What CPU are you using? I've got i3 530 and it needs the "busratio=22" string before booting the apple disc. Check intel site for the busratio. Link to comment Share on other sites More sharing options...
ddrmama Posted July 1, 2010 Author Share Posted July 1, 2010 What CPU are you using? I've got i3 530 and it needs the "busratio=22" string before booting the apple disc. Check intel site for the busratio. Hi! I have i7 860 ¿where you put the busratio??? Thanks Link to comment Share on other sites More sharing options...
dima20202 Posted July 1, 2010 Share Posted July 1, 2010 Hi! I have i7 860 ¿where you put the busratio??? Thanks Your CPU default busratio is 21 ( see Bus/Core Ratio here http://ark.intel.com/Product.aspx?id=41316 )It might help you.... In chameleon, while selecting boot disk. You also may type there -x, -v and other options. Link to comment Share on other sites More sharing options...
MaLd0n Posted July 1, 2010 Share Posted July 1, 2010 http://tonymacx86.blogspot.com/ http://www.insanelymac.com/forum/index.php?showtopic=220312 http://www.insanelymac.com/forum/index.php?showtopic=218539 Link to comment Share on other sites More sharing options...
ddrmama Posted July 2, 2010 Author Share Posted July 2, 2010 Thank you for your answers. I have tried to do following the guide with is in tonymacx86 (installing [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url]+[url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url]) and I couldn´t do it. I think that could be my graphic card (ATI HD5670) that is not supported yet, but I thought that SL would use a generic graphic card to be able to install the OSX. I think this because when I am installing SL all is ok but after the monitor shut down (no signal) and the installation I think that stops (because I can´t see the monitor to know what happens). Any idea for this?? Thank you very much!! Link to comment Share on other sites More sharing options...
hom.hom Posted August 9, 2010 Share Posted August 9, 2010 i have about the same system, only i have a hd 5770 from ASUS, and found a version of Empire Efi that does the trick: legacyempire_efi1085, not completely though but it boots under the condition of each time booting with this disc... Link to comment Share on other sites More sharing options...
Recommended Posts