raj_kumar130 Posted August 5, 2009 Share Posted August 5, 2009 installed: iDeneb 1.5-10.57 on my IBM Thinkcenter 8173, did not select ethernet driver from from dvd because it was not listed. As a result my internet is not working, everything else works fine after the install. Broadcom ethernet drivers are listed on dvd but not BCM 5705. If someone knows which driver on dvd will work, please let us know. I am new to the Mac scene. Specifications Processor Intel® Pentium 4 Processor 540 (3.2GHz) with 800MHz system bus Hyper-Threading (HT) technology 1MB L2 cache Chipset Intel 915G Express Chipset 82915G Graphics Memory Controller Hub (GMCH) 82801FB I/O Controller Hub (ICH6) for SATA150, ATA-100 EIDE, PCI Express x1, PCI 2.3 bus, USB, Low Pin Count interface National Semiconductor® PC8375T Super I/O for security chip (TPM), Asset ID, serial, parallel, diskette, keybrd, mouse, auto-thermal controls, hardware event log Memory 1GB DDR SDRAM (2 x 512MB) installed Two 184-pin gold plated DIMM sockets, up to 2GB max Support up to PC3200 400MHz Dual channel capable HDD 80GB / SATA150 7200 rpm SATA Controller Serial ATA 1.0 / 150 MB/sec SATA150 / integrated in ICH6 One SATA cable (one 1-drop to disk) / two SATA connectors on systemboard Optical Drive 16X DVD-ROM / EIDE IDE Controller Enhanced IDE / ATA-100 / integrated in I/O Controller Hub (ICH6) one 1-drop EIDE 80-conductor cable to optical FDD 3.5" 1.44MB diskette drive Graphics Intel Graphics Media Accelerator 900 (GMA 900) Integrated graphics in 915G GMCH Uses main memory (up to 128MB with 256MB+) One 15-pin analog D-sub connector Audio Integrated digital audio SoundMAX® Cadenza Software-based audio (done by processor and ICH6) AC ’97 interface ADI1981B codec Ethernet 10/100/1000 gigabit ethernet on planar Broadcom® NetXtreme™ Gigabit Network Connection BCM5705 controller PHY and MAC layer Full duplex / Wake on LAN® / ACPI 1.1 / PXE 2.0 and RPL remote boot Modem N/A Interface Ports Front: - 2 x USB 2.0 - 1 x microphone (stereo) - 1 x headphone (stereo) Back - 6 x USB 2.0 - 2 x 9-pin serial - 1 x parallel (25-pin) - 1 x keyboard (PS/2) - 1 x mouse (PS/2) - 1 x ethernet (RJ-45) - 1 x monitor (DB-15) Drive Bays External: - 1 x 3.5" Slimline Drive Bay - 1 x 5.25"Drive Bay Internal: - 1 x 3.5" Drive Bay Expansion Slots Slot 1: half-length (175mm), full-height, 32-bit PCI 2.3 (5v) Slot 2: half-length (175mm), full-height, PCI Express x1 Power Supply 225 Watts with variable speed fan Cooling Three variable speed fans (two in front; power supply fan in back) Dimension 12.2" W X 14.1" D X 3.3" H (3.4"H with feet) 310mm W X 358mm D X 85mm H (87.5mm H with feet) Link to comment https://www.insanelymac.com/forum/topic/178296-broadcom-nextreme-bcm-5705-ethernet-driver/ Share on other sites More sharing options...
Recommended Posts