Jump to content
4 posts in this topic

Recommended Posts

Hey all,

 

I installed IPC 10.5.6 Final on my computer after partitioning the primary drive which has Vista on it.

 

The installation went through fine and at the end of the install there is a message saying that you need to restart your computer. FINE. Restarted it BUT cant get an entry for OS 10 on the boot menu....meaning i have nothing to boot!

 

After that I tried locating the chain0 on the install DVD and tried performing the C:/chain0:"MacOS" trick in boot.ini but to no avail - went back, rebooted, selected teh MacOS entry but it just goes in an inifite loop and nothing happens.

 

ANY suggestions plz......my computer is a 1.6 GHz, Intel Core 2 Duo Toshiba Satellite A-100 with 1GB of ram. Again one part of the partition is vista the other is the new OS 10.5.6.

 

Oh and I tried -v afterwords with the boot DVD but that just gets me back to the installation menu.

 

Thanks

Link to comment
https://www.insanelymac.com/forum/topic/164763-ipc-1056-dual-boot-installation/
Share on other sites

Hey all,

 

I installed IPC 10.5.6 Final on my computer after partitioning the primary drive which has Vista on it.

 

The installation went through fine and at the end of the install there is a message saying that you need to restart your computer. FINE. Restarted it BUT cant get an entry for OS 10 on the boot menu....meaning i have nothing to boot!

 

After that I tried locating the chain0 on the install DVD and tried performing the C:/chain0:"MacOS" trick in boot.ini but to no avail - went back, rebooted, selected teh MacOS entry but it just goes in an inifite loop and nothing happens.

 

ANY suggestions plz......my computer is a 1.6 GHz, Intel Core 2 Duo Toshiba Satellite A-100 with 1GB of ram. Again one part of the partition is vista the other is the new OS 10.5.6.

 

Oh and I tried -v afterwords with the boot DVD but that just gets me back to the installation menu.

 

Thanks

 

Fist install Visa,then install the Mac OS X.After finishing installed Mac,insert DVD vista to repair and enter command promt :

 

Diskpart

 

List disk

Select disk 0

List partitition

Select partition 1

Active

exit

exit

 

and choose automatic repair,restart the computer and it will log in to Win Vista

 

open google and search for the software "EasyBCD" set it up and under add/remove ----) the Tab select OS X 86 add it and remember to save it.

 

Restart your cpmputer and enjoy the beautiful MAC

Thanks a lot for the reply. However, I am a little confused here, when I go to list the partitions I get the following:

 

Parittion Type Size Offset

 

Partition 1 .... OEM.....1500 MB ... 1024 KB

Partition 2 ... Primary ..72 GB ..... 1501 MB

Partition 0 ... Extended ...29 GB....73 GB

Parittion 3 .... Logical ...29 GB ... .. 73 GB

 

You said to select partition 1, by that do u mean select the Vista Partition? (Partition 2 here)...or the Mac os partition (Partition 0 for me).

 

Thanks!

Thanks a lot for the reply. However, I am a little confused here, when I go to list the partitions I get the following:

 

Parittion Type Size Offset

 

Partition 1 .... OEM.....1500 MB ... 1024 KB

Partition 2 ... Primary ..72 GB ..... 1501 MB

Partition 0 ... Extended ...29 GB....73 GB

Parittion 3 .... Logical ...29 GB ... .. 73 GB

 

You said to select partition 1, by that do u mean select the Vista Partition? (Partition 2 here)...or the Mac os partition (Partition 0 for me).

 

Thanks!

 

Yes,select the Vista Partition.

×
×
  • Create New...