Jump to content

USB devices work only if plugged in at boot


yomogi
 Share

3 posts in this topic

Recommended Posts

Hello everyone. I've got a BenQ R55 and have installed OS X via Kaly's 10.5.2 v8 EFI, and have gotten the majority of the hardware to work (sans the 3945 wifi).

 

The problem I'm having is that none of my usb devices, be it a flash disk, ipod, keyboard, mouse, etc will not work unless I have at least 1 usb device plugged in during bootup.

Is there anybody else having this problem? My dmesg is below.

 

 immediate dependencies on both com.apple.kernel and com.apple.kpi components; use only one style.
Extension "com.apple.driver.AppleACPIPlatform" has immediate dependencies on both com.apple.kernel and com.apple.kpi components; use only one style.
pciBridgeCheckConfiguration(bus 0, state 1)
Checking PCI bus 0
 BIOS config retained
pciBridgeCheckConfiguration(bus 1, state 0)
Checking PCI bus 1
 BIOS config retained
pciBridgeCheckConfiguration(bus 2, state 0)
Checking PCI bus 2
 BIOS config retained
pciBridgeCheckConfiguration(bus 8, state 0)
Checking PCI bus 8
 BIOS config retained
pciBridgeCheckConfiguration(bus 4, state 0)
Checking PCI bus 4
 BIOS config retained
pciBridgeCheckConfiguration(bus 5, state 0)
Checking PCI bus 5
 MEM: new range size 200000 align 100000 flags 1
 PFM: new range size 0 align 100000 flags 0
 I/O: new range size 1000 align 1000 flags 1
 BUS: new range size 2 align 1 flags 1
PCI configuration changed (bridge=1 device=15 yenta=1)
Extension "com.apple.driver.AppleACPIPlatform" has immediate dependencies on both com.apple.kernel and com.apple.kpi components; use only one style.
Extension "com.apple.driver.AppleACPIPlatform" has immediate dependencies on both com.apple.kernel and com.apple.kpi components; use only one style.
mbinit: done
Security auditing service present
BSM auditing present
From path: "uuid", Starting AppleACPIPS2Nub

Waiting for boot volume with UUID AAE6727B-3A62-3C20-9AD1-257C6A0172BA
Waiting on IOProviderClassIOResourcesIOResourceMatchboot-uuid-media
Found mouse PNP device
AppleACPIPS2Nub startup complete
USBF:	2.870	Attempting to get EHCI Controller from BIOS
USBF:	2.870	USBLEGCTLSTS value c0002000
USBF:	2.870	Found USBLEGSUP_ID - value 0x1000001 - writing OSOwned
USBF:	2.870	acquireOSOwnership done - value 0x1000001
IOPCCard info:   Mac OS X PCMCIA Card Services 3.1.22
IOPCCard info:     options:  [pci] [cardbus] [pnp]
IOPCCard info:   Intel PCIC probe: 
IOPCCard info:     TI XX12 rev 00 PCI-to-CardBus phys mem 0x60104000 virt mem 0x2bb42000
IOPCCard info:       host opts [0]: [serial pci & irq] [pci irq 18] [lat 64/64] [bus 6/6]
IOPCCard info:       PCI card interrupts, PCI status changes
Extension "com.apple.iokit.AppleYukon2" has immediate dependencies on both com.apple.kernel and com.apple.kpi components; use only one style.
FireWire (OHCI) TI ID 803a PCI now active, GUID 00c09f0000d15714; max speed s400.
Got boot device = IOService:/AppleACPIPlatformExpert/PCI0@0/AppleACPIPCI/SATA@1F,2/AppleIntelPIIXATARoot/PRT0@0/AppleIntelICHxSATA/ATADeviceNub@0/AppleATADiskDriver/IOATABlockStorageDevice/IOBlockStorageDriver/FUJITSU MHV2080BH PL FUJITSU MHV2080BH PL/IOFDiskPartitionScheme/Untitled 1@1
BSD root: disk0s1, major 14, minor 1
jnl: unknown-dev: replay_journal: from: 4817408 to: 2335232 (joffset 0x257000)
jnl: unknown-dev: journal replay done.
ERROR: FireWire unable to determine security-mode; defaulting to full-secure.
Jettisoning kernel linker.
yukon: Ethernet address 00:16:36:bc:6a:4d
Resetting IOCatalogue.
VGA: family specific matching fails
Matching service count = 2
ACPI_SMC_CtrlLoop::initCPUCtrlLoop - pmCPUControl (PMIOCSETPSTATETABLE) returned 0xffffffff
AppleYukon2 - en0 link active, 1000-Mbit, full duplex, symmetric flow control enabled port 0
NVDANV40HAL loaded and registered.
ApplePS2Trackpad: Synaptics TouchPad v5.10
dsmos: Initializing...
dsmos: Hook and decryption contexts set!
dsmos: Starting...
VGA: family specific matching fails
NVinjectGo: Probing.
NVinjectGo: Setting model=Graphics by NVIDIA
NVinjectGo: Setting @0,device_type=display
NVinjectGo: Setting @1,display-type=LCD
NVinjectGo: Setting @0,compatible=NVDA,NVMac
NVinjectGo: Setting NVCAP=
NVinjectGo: Setting @1,name=NVDA,Display-B
NVinjectGo: Setting device_type=NVDA,GeForce
NVinjectGo: Setting name=NVDA,Parent
NVinjectGo: Setting rom-revision=NVinjectGo 0.2.0
NVinjectGo: Setting @0,name=NVDA,Display-A
NVinjectGo: Setting @1,compatible=NVDA,NVMac
NVinjectGo: Setting @1,device_type=display

Link to comment
Share on other sites

 Share

×
×
  • Create New...