malus_01 Posted August 21, 2008 Share Posted August 21, 2008 This is my first post. I usually hunt around and look for answers to resolve any issues I have, but I am completely stumped on this one. So your help will be much appreciated! First let me say I have downloaded and tried almost every version of Kalyway and never got past the Darwin Bootloader screen. So then I tried iatkos v4i and I was able to actually get to all the good stuff. I followed the directions (as per http://www.demonoid.com/files/details/1554158/14696248) and I was able to get Leopard to install. But once the computer restarted (I had removed the DVD once install was complete) it went through the Darwin Bootloader screen again (I let the time run down) and then it restarted the PC again. And on and on this went. I tried -v -x -f -s commands, but it did nothing. My question is what options should I be selecting on the "Custom Install on 'Mac'" screen (seen below)? And is there anything else that I am missing? Here are all the specs on the PC I am attempting to use: HP Pavilion a335w Desktop PC Base processor * Intel Pentium4/2.5 GHz: * 400 MHz front side bus * Socket mPGA478 Chipset * 845GL Motherboard manufacturer Feature/specification: Trigem motherboard Motherboard name: Glendale System BIOS supplier: Phoenix Form factor: uATX Processor brand: Intel Processor socket type: mPGA478 Processor family: P4 and Celeron (Willamette, Northwood) Processor front side bus (FSB): 400 MHz Chipset name: 845GL Chipset "north bridge": 845GL, rev. A1 Chipset "south bridge": ICH4, rev. A1 Super I/O: SMSC LPC47M102, REV. VS142AV Flash BIOS device: FWH 4 MB Memory type: DDR Memory speed: PC2100, PC2700 messages at PC2100 Memory sockets: 2 DIMMS, 184 pin Maximum memory: 2 GB (2 x 1 GB) Graphics supplier: Intel Graphics configuration: Integrated in chipset Onboard graphics memory: UMA/up to 64 MB shared with system Graphics connector (AGP): None Audio: AC'97, integrated Audio CODEC device: ADI1981A Audio jacks: Microphone, Line-in, Line-out, Speaker Ethernet 10/100 supplier: Realtek RTL8100 Ethernet configuration: PCI, intergrated IDE UDMA modes: ATA-66/100 Expansion slots: Three PCI USB ports: Six USB front/back panel options: 2 front, 4 back External ports: 1 serial, 1 parallel, 1 floppy, PS/2 keyboard, PS/2 mouse Manufacturer's options available: Intergrated graphics, LAN on motherboard, integrated audio Memory * 756 MB 184 pin, PC133 DDR1-333 SDRAM (256MB and 512MB) Hard drive * 80 GB Ultra DMA * 5400 rpm Video graphics * Integrated Intel Extreme graphics with up to 64 MB main system memory allocated for video memory Sound/audio * Integrated AC97 audio Network (LAN) * Integrated 10/100Base-T networking interface * Realtek RTL8100 I know it's a lot of info on the Motherboard, but I wanted to make sure that you peeps know all the details on it. Your help is much appreciated! Link to comment https://www.insanelymac.com/forum/topic/122109-install-help-hp-pavilion-a335w-pc-using-iatkos-v4i/ Share on other sites More sharing options...
malus_01 Posted August 22, 2008 Author Share Posted August 22, 2008 Bump Link to comment https://www.insanelymac.com/forum/topic/122109-install-help-hp-pavilion-a335w-pc-using-iatkos-v4i/#findComment-864623 Share on other sites More sharing options...
malus_01 Posted August 23, 2008 Author Share Posted August 23, 2008 Bump. Anybody? Link to comment https://www.insanelymac.com/forum/topic/122109-install-help-hp-pavilion-a335w-pc-using-iatkos-v4i/#findComment-865694 Share on other sites More sharing options...
Recommended Posts