KaptenKresh Posted July 2, 2008 Share Posted July 2, 2008 Hi! I have a Gigabyte radeon x1550 256mb card, using chipset 0x7183 (Same as most x1300 models) and i'm using the Natit_ATIauto kext. I can change the resolution but i can't play DVDs/Games etc. (QE/CI not enabled.) But when i updated my system from 10.5.2 to 10.5.4 the system info says this: ATI Radeon X1300 Series: Chipset Model: ATI Radeon X1300 Series Type: Display Bus: PCIe PCIe Lane Width: x16 VRAM (Total): 256 MB Vendor: ATI (0x1002) Device ID: 0x7183 Revision ID: 0x0000 Displays: L226W: Resolution: 1680 x 1050 @ 60 Hz Depth: 32-bit Color Core Image: Software Main Display: Yes Mirror: Off Online: Yes Quartz Extreme: Not Supported Display Connector: Status: No display connected Does "Core image: Software" means that CI is working? Also, i'd like to know if theres a way for me to get QE working too... System speccs: Leo4allv3 10.5.4 Gigabyte GA-S55 motherboard AMD athlon x2 2.1ghz 4000+ 2gb RAM Gigabyte radeon X1550 256mb ram 250gb sata Thanks in advance! Kresh Link to comment https://www.insanelymac.com/forum/topic/113603-x1300-0x7183-ci-enabled-but-not-qe/ Share on other sites More sharing options...
SticMAC™ Posted July 2, 2008 Share Posted July 2, 2008 I'm afraid I have bad news!! That specific chipset cannot be set to support QE/CI! The issue is around a seperate device ID being used for the secondary output. If you edit the ATIRadeonX1000.kext and add the DeviceID to it, it is sure to give you a Kernel Panic! You can try but I had this specific card in my Dell and replaced it with a ASUS EN7300GS(256MB). The alternative DeviceID for the secondary Output is 0x71A3, but you cannot get the system past the bootloader if you add anyone of the two to the ATIRadeonX1000.kext. With all the kexts loaded and without the Ids added to the ATIRadeonX1000.kext you are able to set the resolutiong but still nothing works SticMAN Link to comment https://www.insanelymac.com/forum/topic/113603-x1300-0x7183-ci-enabled-but-not-qe/#findComment-804357 Share on other sites More sharing options...
Bronya Posted July 3, 2008 Share Posted July 3, 2008 Hi! I have a Gigabyte radeon x1550 256mb card, using chipset 0x7183 (Same as most x1300 models) and i'm using the Natit_ATIauto kext. I can change the resolution but i can't play DVDs/Games etc. (QE/CI not enabled.) But when i updated my system from 10.5.2 to 10.5.4 the system info says this: Does "Core image: Software" means that CI is working? Also, i'd like to know if theres a way for me to get QE working too... Thanks in advance! Kresh You download the it driver for 10.5.4 (Ati_for_QE_CI.zip) Unpack and click on load.command and in terminal write real password and run auto reboot. Link to comment https://www.insanelymac.com/forum/topic/113603-x1300-0x7183-ci-enabled-but-not-qe/#findComment-805032 Share on other sites More sharing options...
KaptenKresh Posted July 3, 2008 Author Share Posted July 3, 2008 Ok Bronya, i did as you told me... Opened the load.command in the terminal, wrote my password and the system rebooted... Can't see any difference tho Did i do something wrong? Thanks in advance! Kresh Link to comment https://www.insanelymac.com/forum/topic/113603-x1300-0x7183-ci-enabled-but-not-qe/#findComment-805574 Share on other sites More sharing options...
Bronya Posted July 3, 2008 Share Posted July 3, 2008 Ok Bronya, i did as you told me... Opened the load.command in the terminal, wrote my password and the system rebooted...Can't see any difference tho Did i do something wrong? Thanks in advance! Kresh It is driver for QE/CI ! Try checkup in system profiler Link to comment https://www.insanelymac.com/forum/topic/113603-x1300-0x7183-ci-enabled-but-not-qe/#findComment-806204 Share on other sites More sharing options...
KaptenKresh Posted July 3, 2008 Author Share Posted July 3, 2008 It is driver for QE/CI ! Try checkup in system profiler It still says Core image: Software and Quartz extreme: Not supported... Could it be like SticMAN says, that the device ID aint supported? Link to comment https://www.insanelymac.com/forum/topic/113603-x1300-0x7183-ci-enabled-but-not-qe/#findComment-806268 Share on other sites More sharing options...
KaptenKresh Posted July 3, 2008 Author Share Posted July 3, 2008 Never mind my last post!! It's working now! Worked on my third reboot.. hehe One million thanks Bronya for the help! Link to comment https://www.insanelymac.com/forum/topic/113603-x1300-0x7183-ci-enabled-but-not-qe/#findComment-806311 Share on other sites More sharing options...
Bronya Posted July 3, 2008 Share Posted July 3, 2008 Never mind my last post!! It's working now! Worked on my third reboot.. hehe One million thanks Bronya for the help! Work QE/CI ??? Link to comment https://www.insanelymac.com/forum/topic/113603-x1300-0x7183-ci-enabled-but-not-qe/#findComment-806317 Share on other sites More sharing options...
KaptenKresh Posted July 3, 2008 Author Share Posted July 3, 2008 Yes it is working now :)Core image: Hardware acceleratedQuartz extreme: Supported:DThanks alot!!!Actually, there should be a sticky with that guide.. I've seen many threads where people can't get this device ID to work... Link to comment https://www.insanelymac.com/forum/topic/113603-x1300-0x7183-ci-enabled-but-not-qe/#findComment-806325 Share on other sites More sharing options...
Bronya Posted July 4, 2008 Share Posted July 4, 2008 Enjoy ! Link to comment https://www.insanelymac.com/forum/topic/113603-x1300-0x7183-ci-enabled-but-not-qe/#findComment-806395 Share on other sites More sharing options...
Tibian Ass Monkey Posted July 4, 2008 Share Posted July 4, 2008 Will this work with an ati x1300 ID is 0 x 7187 ? Link to comment https://www.insanelymac.com/forum/topic/113603-x1300-0x7183-ci-enabled-but-not-qe/#findComment-806489 Share on other sites More sharing options...
Bronya Posted July 4, 2008 Share Posted July 4, 2008 Will this work with an ati x1300 ID is 0 x 7187 ? No , you should install original ATIRadeonX1000.kext's Original can work . Link to comment https://www.insanelymac.com/forum/topic/113603-x1300-0x7183-ci-enabled-but-not-qe/#findComment-806500 Share on other sites More sharing options...
ugOSX Posted July 30, 2008 Share Posted July 30, 2008 Where did you get it? Can you tell me all the steps you did? Thank you!! Link to comment https://www.insanelymac.com/forum/topic/113603-x1300-0x7183-ci-enabled-but-not-qe/#findComment-839381 Share on other sites More sharing options...
ozzzzysh Posted August 17, 2008 Share Posted August 17, 2008 Sorry since this thread is old and all but I have the same device ID but when I installed that it rebooted and then I came to the login screen... but when I logged in i saw my wallpaper then my screen went black :-\... right now my kext is disabled so i can trouble shoot... any ideas? Link to comment https://www.insanelymac.com/forum/topic/113603-x1300-0x7183-ci-enabled-but-not-qe/#findComment-859483 Share on other sites More sharing options...
abeeson Posted September 10, 2008 Share Posted September 10, 2008 Same problem, only sometimes i get Light blue / dark blue alternating lines, Safe mode works, im reverting to old ATIRadeonX1000 from install disc, i think Pacifist can get it, then i will give this more goes with other things, i just want QE / CI! Link to comment https://www.insanelymac.com/forum/topic/113603-x1300-0x7183-ci-enabled-but-not-qe/#findComment-885406 Share on other sites More sharing options...
knightrider862 Posted September 13, 2008 Share Posted September 13, 2008 Same problem for me. The kext file was installed and I rebooted the my computer. After the login screen my screen went black and I got sometime Light blue,dark blue,alternating lines like abeeson says. Any idea to fix it? I am new about the driver installition amd uninstallition so I can't disable the kext file and I can't use my leopard now. If anybody can say how can I disable the kext file I will be very happy and I can use my leopard witout QE/CI until the the problem solve. İf I can get QE/CI i can finally use the Leopard fully operational. By the way now I am using AGP ATI RadeonX1300 but the vendor ID and Device Id are same. Link to comment https://www.insanelymac.com/forum/topic/113603-x1300-0x7183-ci-enabled-but-not-qe/#findComment-889216 Share on other sites More sharing options...
leonardoprc Posted September 22, 2008 Share Posted September 22, 2008 I installed the Kext NatitX1300.r1v1.Installer for my video card Radeon X1550 512MB GDDR2 128-bit, but still without QE. My old monitor could be impossible this feature (QE/CI)? Radeon X1300 PRO Series: Modelo do Grupo de Circuitos Integrados: Radeon X1300 PRO Series Tipo: Monitor Barramento: PCIe Largura Lane PCIe: x16 VRAM (Total): 512 MB Fornecedor: ATI (0x1002) ID do Dispositivo: 0x7143 ID da Revisão: 0x0000 Monitores: StudioWorks 560A: Resolução: 1024 x 768 @ 60 Hz Profundidade: Cor de 32 bits Core Image: Software Monitor Principal: Sim Espelho: Desligado On-line: Sim Quartz Extreme: Não Compatível Conector do Monitor: Estado: Nenhum monitor conectado - It would be a matter of old monitor, or really my video card is not yet supported? Link to comment https://www.insanelymac.com/forum/topic/113603-x1300-0x7183-ci-enabled-but-not-qe/#findComment-901441 Share on other sites More sharing options...
elvip Posted December 21, 2008 Share Posted December 21, 2008 UPDATE / EDIT (for posterity): WORKS USED DiaboliK's NatitX1300.kext installer! (Revison #1 - 10.4.9 Version) I NEED HELP MAKING MY X1300 CARDS WORK, HAVE TRIED EVERYTHING IF ANYONE CAN GIVE ME A STEP BY STEP GUIDE PLEASE I'D APPRECIATE IT! TY Link to comment https://www.insanelymac.com/forum/topic/113603-x1300-0x7183-ci-enabled-but-not-qe/#findComment-1009049 Share on other sites More sharing options...
glorgil Posted December 26, 2008 Share Posted December 26, 2008 UPDATE / EDIT (for posterity): WORKS USED DiaboliK's NatitX1300.kext installer! (Revison #1 - 10.4.9 Version) I NEED HELP MAKING MY X1300 CARDS WORK, HAVE TRIED EVERYTHING IF ANYONE CAN GIVE ME A STEP BY STEP GUIDE PLEASE I'D APPRECIATE IT! TY i have your same id (0x7146) and i install the Diabolik's natitx1300.kext installer too...but the ci/qe isn't supported can you help me? what have you done? Link to comment https://www.insanelymac.com/forum/topic/113603-x1300-0x7183-ci-enabled-but-not-qe/#findComment-1014591 Share on other sites More sharing options...
robb007 Posted January 18, 2009 Share Posted January 18, 2009 I have a lot of this solutions tried but i can't get QE/CI (iWork don't work with my PC !) I use pcefiV9 by netkas and i can't put the ati x1000 ga plugin in /Extra. OK, I put this plugin with the extension in /System/Library/Extensions it makes any Kernel Panic but... when the session begin it make a graphic bug with a Kernel Panic !!! Youhou ! ( Note : The busy cursor is present and movable before the KP ! ) (Sorry for my bad english but i'm french) Link to comment https://www.insanelymac.com/forum/topic/113603-x1300-0x7183-ci-enabled-but-not-qe/#findComment-1046397 Share on other sites More sharing options...
kylekittredge Posted September 8, 2009 Share Posted September 8, 2009 I'm afraid I have bad news!! That specific chipset cannot be set to support QE/CI! The issue is around a seperate device ID being used for the secondary output. If you edit the ATIRadeonX1000.kext and add the DeviceID to it, it is sure to give you a Kernel Panic! You can try but I had this specific card in my Dell and replaced it with a ASUS EN7300GS(256MB). The alternative DeviceID for the secondary Output is 0x71A3, but you cannot get the system past the bootloader if you add anyone of the two to the ATIRadeonX1000.kext. With all the kexts loaded and without the Ids added to the ATIRadeonX1000.kext you are able to set the resolutiong but still nothing works SticMAN Link to comment https://www.insanelymac.com/forum/topic/113603-x1300-0x7183-ci-enabled-but-not-qe/#findComment-1256615 Share on other sites More sharing options...
Recommended Posts