SUCCESS Yosemite Hackintosh on MSI H61M-P31/W8

[titus]

SUCCESS Yosemite Hackintosh on MSI H61M-P31/W8

This is MSI H61M-P31/W8 Yosemite hackintosh - SUCCESS (no additional kext, not much work around, i can say everythings is in place)

SPECS:
Mobo (MSI H61M-P31/W8)
Processor: Intel G2020 (thats all i have LOL)
GPU (NVidia GeForce 210 1GB)
Memory (2GB 1600MHZ DDR3)
Storage (1TB Seagate Barracuda), (Optical Drive)
Display (3D Samsung S23A700 23")

##### for Yosemite + ##### for Yosemite

Here where i start:






use four flag “with safe mode”




made 2 partition on 1TB hard drive






After successful initial install, i did the same boot flag “with safe mode”





finally reach the desktop, time for ##### to settle the remaining of the rig


I select the "#####", Realtek version for my Audio and Network




As you can see net is working just fine


Audio, it takes a second round - - - i trash what i have on S/L/E and install it again with #####, it worked like a charm with Internal speaker as setting


After that last image, i reboot (boot in HDD)
<<<  GPT error >>> reboot again using ##### (same flag i use before) and tonymacx86 official GPT error thread  FIX the situation swiftly
reboot again in HDD (without any flag)
<<< nothin happen >>>
reboot again with one flag npci=0x2000
<<< nothin happen >>>
reboot again with one flag Graphics Enabler=Yes
it BOOT.... WOW
##### Customization fix the GraphicEnabler=Yes (just that one i tick)
and it finally settle my MSI H61M-P31/W8 Yosemite hackintosh >>SUCCESS booting without any flag, with audio and net with 1TB hdrive with 3D Display monitor

[Cubefishuk]

Thanks for posting this.

 

My system:

Mobo: MSI H61M-P31/W8

CPU: i7-3770

8GB RAM

GPU: Zotac GT440 1GB

SSD: Samsung EVO 250GB

WIFI: TP Link TL-725n USB

... and, of course, a monitor (connnected via HDMI) and DVD-RW drive.

 

I used qlover Note to create the Yosemite 10.10.3 installation USB drive, and set the motherboard to be UEFI rather than Legacy + UEFI as qlover Note is for EFI systems.

 

Installation went fine, and the 'unmentionable Beast' was used to install drivers for LAN (Realtek 8111) and VooDoo audio. After this, Clover Configurator was used to set up the config.plist file on the EFI partition of the SSD. Clover configurator will generate a config file that is almost perfect, so only a few tweaks are need. Clover Configurator makes it a doddle to add various flags. The settings I added are:

 

npci=0x3000

GraphicsEnabler=Yes

 

I found that if I had npci=0x2000 and no entry for GraphicsEnabler, then the first boot was unsuccessful - after the Apple logo, the screen would go blank and no input was detected.

 

The  GPU worked perfectly with no need for the official nVidia driver; the WIFI required drivers for RTL-8188EU; and I had to tweak the Voodoo KEXT to prevent it from producing hiss as follows:

 

Open Terminal and type

cd /System/Library/Extensions/VoodooHDA.kext/Contents

sudo nano Info.plist

 

Locate the entry for iGain and change the value to 0 (zero)

Save and exit

 

That's it; all done!

 

Further information in qlover Note and Clover Configurator can be found at: http://mymac4music.com/