Jump to content

3,268 posts in this topic

Recommended Posts

Anyone have an idea why my OC stalls out when I connect a second bootable SATA SSD to the motherboard? Used with just one SATA drive, I can boot perfectly into Mojave in about 13 seconds and everything work perfectly. If I connect a second SSD with Windows or another MacOS install, OC takes over 4 minutes to reach the picker menu. I also can't boot up Windows if I try. If I use a Clover USB stick, I can see and boot from both drives fast and without issue.

 

Here is my EFI folder

Here is a log of a fast, single drive boot.

Here is a log of a stalled, dual drive boot.

 

I added the photo of my monitor because there is more info displayed at the point it gets stuck than what's written to the log. How could I get the log to write even more? I have debug target set to <75>

 

This EFI and config were made following the Vanilla Desktop Guide to the best of my abilities. I also tried this without the UsbKbDxe.efi and I tried swapping the VBoxHfs.efi for HFSPlus.efi with no change.

Thank you for any insight!

OC Driver ApfsDriverLoader.efi.JPG

Edited by hoffsta
Additional Information

Share this post


Link to post
Share on other sites
Advertisement
12 hours ago, pitrysha said:

If  do not enable the CPU Emulate or Patch _xcpm_bootstrap © Pike R. Alpha, the system will not boot. Сan enable PMDrvr.text instead. How right?

Архив.zip

pictures you attached is a normal beahviour for your Haswell EP CPU (v3 xeon)
you can use  kext or normal patching with the help of bootloader you want to use as suggested in previous message

V4 xeon are Broadwell EP and can work well the same using proper Patches and fakecpuid or using automatic bootloader way to patch it

Higher and modern cpu as 7980xe or 9980 xe are different and they could need only an unlocked CFG lock parameter in motherboard bios to work
I think @nmano cpu problem with geekbench is a different problem, maybe with some failure in components of his rig

 

Edited by fabiosun

Share this post


Link to post
Share on other sites
Skylake X->Skylake U 0x0406E3
Cpuid1Data   <->  E3060400 00000000 00000000 00000000 
Cpuid1Mask  <->   FFFFFFFF 00000000 00000000 00000000 
Haswell-E->Haswell 0x0306C3
Cpuid1Data   <->  C3060300 00000000 00000000 00000000
Cpuid1Mask  <->   FFFFFFFF 00000000 00000000 00000000 
  
Broadwell-E->Broadwell 0x0306D4
Cpuid1Data   <-> D4060300 00000000 00000000 00000000
Cpuid1Mask  <->  FFFFFFFF 00000000 00000000 00000000

Thanks Team.

Edited by nmano

Share this post


Link to post
Share on other sites
32 minutes ago, nmano said:


 

Haswell-E->Haswell 0x0306C3
Cpuid1Data   <->  C3060300 00000000 00000000 00000000
Cpuid1Mask  <->   FFFFFFFF 00000000 00000000 00000000 
  
Broadwell-E->Broadwell 0x0306D4
Cpuid1Data   <-> D4060300 00000000 00000000 00000000
Cpuid1Mask  <->  FFFFFFFF 00000000 00000000 00000000

Thanks Team.

For your x299 processor, see the information here.

https://pikeralpha.wordpress.com/2017/08/18/xeon-microcode-found-in-imac-pro-firmware/

Cpuid1Data   <->  E3060500 00000000 00000000 00000000

Share this post


Link to post
Share on other sites

I test with clover its worked open core not yet.

CPU ->Type 0x0F01

Cpu-type 010f

88107496_ScreenShot2020-01-11at7_33_57AM.thumb.png.cc062fbb3e77b93304cc1bdb13ce9561.png

 

I have 8 Memory Slots but I can see 4 Slots

PlatformFeature  0x20

 

1394364877_ScreenShot2020-01-11at8_14_18AM.thumb.png.bed0ba4af039eff55e2accb8d425e535.png

Edited by nmano

Share this post


Link to post
Share on other sites

Hi, i recently moved to opencore but I have been having some weird crashes. It happens randomly at any time without any warning or error messages after hard reboot. I managed to grab a picture when it happened: 

 

 

IMG_20200111_122355.jpg

 

Everything works on my machine, don't know if it's nvram related or some missing configuration.

 

System specs:

MB: MSI B250I Gaming Pro AC

CPU: i7 7700

GPU: HD630

RAM: 16GB DDR4 2400

NVME: Samsung 970 Pro 1TB

WIFI: TP Link AC1300 Archer T6E

BT: Asus BT400 USB

 

EFI.zip

Edited by rottenpants

Share this post


Link to post
Share on other sites
14 hours ago, rottenpants said:

Hi, i recently moved to opencore but I have been having some weird crashes. It happens randomly at any time without any warning or error messages after hard reboot. I managed to grab a picture when it happened: 

 

 

IMG_20200111_122355.jpg

 

Everything works on my machine, don't know if it's nvram related or some missing configuration.

 

System specs:

MB: MSI B250I Gaming Pro AC

CPU: i7 7700

GPU: HD630

RAM: 16GB DDR4 2400

NVME: Samsung 970 Pro 1TB

WIFI: TP Link AC1300 Archer T6E

BT: Asus BT400 USB

 

EFI.zip

 

get an AMD GPU (RX 560/570/580 or Vega 56/64), disable the damn HD630, then use MacPro7,1 SMBIOS

Share this post


Link to post
Share on other sites

Thank you OpenCore Developers for implementing the latest XCPM patch.

I would like to give some context here for other users, still working on the X99 platform.

 

With the new  

AppleXcpmForceBoost

you dont need the performance patches anymore, that were needed to get a decent system running. So with the other XCPM patches, no kernel patches are required anymore... everything is covered by the XCPM Quirks.

This might be useful in the documentation as well.

So basically I can get rid of the following patch I have used so far (and that patch also needed constant updates):

 

Comment    String  <-> XCPM Performance fix by @PMheart 
Disabled   Boolean <-> No
Find       Data<-> C1E30848 63D389D0 48C1EA20 
MatchOS    String <-> 10.14.x,10.15.x
Replace    Data<->C1E308B8 00FF0000 31D29090 

 

it seems now that the only kext-patch in the Kernel section for X99 boards is the IOPCIFamily one, without it the system will not boot due to kernel panic.

Comment         String  <-> 5960XPatch 10.14 by PMHeart
Disabled        Boolean <-> No
Find            Data<-> 483D0000 0040
InfoPlistPatch  Boolean <-> No
MatchOS         String <-> 10.14.x,10.15.x
Name            String<-> IOPCIFamily
Replace         Data<-> 483D0000 0080

Would it make sense to implement this as a Quirk as well?

 

Mike

 

Edit:

After some more testing, AppleXcpmForceBoost is not needed. The other XCPM Quirks do the job perfectly.

My conclusion is that AppleXcpmForceBoost is not needed for X99 systems most likely, in my case even caused problems around sleep.

 

Thanks, Mike

 

Edited by Mike Ranger

Share this post


Link to post
Share on other sites

What would be the appropriate way to disable Discrete GPU on my laptop with _OSI Darwin, current SSDT:

DefinitionBlock("", "SSDT", 2, "V330", "_DDGPU", 0)
{
    External (_SB_.PCI0.RP01.PEGP.HGOF, MethodObj)
    Device(RMD1)
    {
        Name(_HID, "RMD10000")
        Method(_INI)
        {
            If (CondRefOf (\_SB.PCI0.RP01.PEGP.HGOF))
            {
                \_SB.PCI0.RP01.PEGP.HGOF (Zero)
            }
        }
    }
}

Also the SSDT to combine Dual Batteries would be appreciated as well:

// Lenovo V330-15IKB Dual Battery Support SSDT with Hotswap capability
// Note: you must enable config.plist /ACPI/DSDT/Patches related to BAT0 & BAT1 to have working dual battery

DefinitionBlock ("", "SSDT", 2, "V330", "_BATC", 0)
{
    External(_SB.PCI0.LPCB.EC0, DeviceObj)
    Scope(_SB.PCI0.LPCB.EC0)
    {
        External(BAT0, DeviceObj)
        External(BAT0._HID, IntObj)
        External(BAT0._STA, MethodObj)
        External(BAT0._BIF, MethodObj)
        External(BAT0._BST, MethodObj)
        External(BAT1, DeviceObj)
        External(BAT1._HID, IntObj)
        External(BAT1._STA, MethodObj)
        External(BAT1._BIF, MethodObj)
        External(BAT1._BST, MethodObj)
        
        Device(BATC)
        {
            Name(_HID, EisaId ("PNP0C0A"))
            Name(_UID, 0x02)

            Method(_INI)
            {
                // disable original battery objects by setting invalid _HID
                ^^BAT0._HID = 0
                ^^BAT1._HID = 0
            }

            Method(CVWA, 3)
            // Convert mW to mA (or mWh to mAh)
            // Arg0 is mW or mWh (or mA/mAh in the case Arg2==0)
            // Arg1 is mV (usually design voltage)
            // Arg2 is whether conversion is needed (non-zero for convert)
            // return is mA or mAh
            {
                If (Arg2)
                {
                    Arg0 = (Arg0 * 1000) / Arg1
                }
                Return(Arg0)
            }

            Method(_STA)
            {
                // call original _STA for BAT0 and BAT1
                // result is bitwise OR between them
                Return(^^BAT0._STA() | ^^BAT1._STA())
            }

            Name(B0CO, 0x00) // BAT0 0/1 needs conversion to mAh
            Name(B1CO, 0x00) // BAT1 0/1 needs conversion to mAh
            Name(B0DV, 0x00) // BAT0 design voltage
            Name(B1DV, 0x00) // BAT1 design voltage

            Method(_BST)
            {
                // Local0 BAT0._BST
                // Local1 BAT1._BST
                // Local2 BAT0._STA
                // Local3 BAT1._STA
                // Local4/Local5 scratch

                // gather battery data from BAT0
                Local0 = ^^BAT0._BST()
                Local2 = ^^BAT0._STA()
                If (0x1f == Local2)
                {
                    // check for invalid remaining capacity
                    Local4 = DerefOf(Local0[2])
                    If (!Local4 || Ones == Local4) { Local2 = 0; }
                }
                // gather battery data from BAT1
                Local1 = ^^BAT1._BST()
                Local3 = ^^BAT1._STA()
                If (0x1f == Local3)
                {
                    // check for invalid remaining capacity
                    Local4 = DerefOf(Local1[2])
                    If (!Local4 || Ones == Local4) { Local3 = 0; }
                }
                // find primary and secondary battery
                If (0x1f != Local2 && 0x1f == Local3)
                {
                    // make primary use BAT1 data
                    Local0 = Local1 // BAT1._BST result
                    Local2 = Local3 // BAT1._STA result
                    Local3 = 0  // no secondary battery
                }
                // combine batteries into Local0 result if possible
                If (0x1f == Local2 && 0x1f == Local3)
                {
                    // _BST 0 - Battery State - if one battery is charging, then charging, else discharging
                    Local4 = DerefOf(Local0[0])
                    Local5 = DerefOf(Local1[0])
                    If (Local4 == 2 || Local5 == 2)
                    {
                        // 2 = charging
                        Local0[0] = 2
                    }
                    ElseIf (Local4 == 1 || Local5 == 1)
                    {
                        // 1 = discharging
                        Local0[0] = 1
                    }
                    ElseIf (Local4 == 5 || Local5 == 5)
                    {
                        // critical and discharging
                        Local0[0] = 5
                    }
                    ElseIf (Local4 == 4 || Local5 == 4)
                    {
                        // critical
                        Local0[0] = 4
                    }
                    // if none of the above, just leave as BAT0 is

                    // Note: Following code depends on _BIF being called before _BST to set B0CO and B1CO

                    // _BST 1 - Battery Present Rate - Add BAT0 and BAT1 values
                    Local0[1] = CVWA(DerefOf(Local0[1]), B0DV, B0CO) + CVWA(DerefOf(Local1[1]), B1DV, B1CO)
                    // _BST 2 - Battery Remaining Capacity - Add BAT0 and BAT1 values
                    Local0[2] = CVWA(DerefOf(Local0[2]), B0DV, B0CO) + CVWA(DerefOf(Local1[2]), B1DV, B1CO)
                    // _BST 3 - Battery Present Voltage - Average BAT0 and BAT1 values
                    Local0[3] = (DerefOf(Local0[3]) + DerefOf(Local1[3])) / 2
                }
                Return(Local0)
            } // _BST

            Method(_BIF)
            {
                // Local0 BAT0._BIF
                // Local1 BAT1._BIF
                // Local2 BAT0._STA
                // Local3 BAT1._STA
                // Local4/Local5 scratch

                // gather and validate data from BAT0
                Local0 = ^^BAT0._BIF()
                Local2 = ^^BAT0._STA()
                If (0x1f == Local2)
                {
                    // check for invalid design capacity
                    Local4 = DerefOf(Local0[1])
                    If (!Local4 || Ones == Local4) { Local2 = 0; }
                    // check for invalid max capacity
                    Local4 = DerefOf(Local0[2])
                    If (!Local4 || Ones == Local4) { Local2 = 0; }
                    // check for invalid design voltage
                    Local4 = DerefOf(Local0[4])
                    If (!Local4 || Ones == Local4) { Local2 = 0; }
                }
                // gather and validate data from BAT1
                Local1 = ^^BAT1._BIF()
                Local3 = ^^BAT1._STA()
                If (0x1f == Local3)
                {
                    // check for invalid design capacity
                    Local4 = DerefOf(Local1[1])
                    If (!Local4 || Ones == Local4) { Local3 = 0; }
                    // check for invalid max capacity
                    Local4 = DerefOf(Local1[2])
                    If (!Local4 || Ones == Local4) { Local3 = 0; }
                    // check for invalid design voltage
                    Local4 = DerefOf(Local1[4])
                    If (!Local4 || Ones == Local4) { Local3 = 0; }
                }
                // find primary and secondary battery
                If (0x1f != Local2 && 0x1f == Local3)
                {
                    // make primary use BAT1 data
                    Local0 = Local1 // BAT1._BIF result
                    Local2 = Local3 // BAT1._STA result
                    Local3 = 0  // no secondary battery
                }
                // combine batteries into Local0 result if possible
                If (0x1f == Local2 && 0x1f == Local3)
                {
                    // _BIF 0 - Power Unit - 0 = mWh | 1 = mAh
                    // set B0CO/B1CO if convertion to amps needed
                    B0CO = !DerefOf(Local0[0])
                    B1CO = !DerefOf(Local1[0])
                    // set _BIF[0] = 1 => mAh
                    Local0[0] = 1
                    // _BIF 4 - Design Voltage - store value for each Battery in mV
                    B0DV = DerefOf(Local0[4]) // cache BAT0 voltage
                    B1DV = DerefOf(Local1[4]) // cache BAT1 voltage
                    // _BIF 1 - Design Capacity - add BAT0 and BAT1 values
                    Local0[1] = CVWA(DerefOf(Local0[1]), B0DV, B0CO) + CVWA(DerefOf(Local1[1]), B1DV, B1CO)
                    // _BIF 2 - Last Full Charge Capacity - add BAT0 and BAT1 values
                    Local0[2] = CVWA(DerefOf(Local0[2]), B0DV, B0CO) + CVWA(DerefOf(Local1[2]), B1DV, B1CO)
                    // _BIF 3 - Battery Technology - leave BAT0 value
                    // _BIF 4 - Design Voltage - average BAT0 and BAT1 values
                    Local0[4] = (B0DV + B1DV) / 2
                    // _BIF 5 - Design Capacity Warning - add BAT0 and BAT1 values
                    Local0[5] = CVWA(DerefOf(Local0[5]), B0DV, B0CO) + CVWA(DerefOf(Local1[5]), B1DV, B1CO)
                    // _BIF 6 - Design Capacity of Low - add BAT0 and BAT1 values
                    Local0[6] = CVWA(DerefOf(Local0[6]), B0DV, B0CO) + CVWA(DerefOf(Local1[6]), B1DV, B1CO)
                    // _BIF 7+ - Leave BAT0 values for now
                }
                Return(Local0)
            } // _BIF
        } // BATC
    }
}

Thanks !

Share this post


Link to post
Share on other sites
13 hours ago, justin said:

 

get an AMD GPU (RX 560/570/580 or Vega 56/64), disable the damn HD630, then use MacPro7,1 SMBIOS

 

Yeah i was thinking about that yesterday. I dont know if i should get a vega 64 card or a newer 5700 navi card.

 

Do you think that the hd630 is causing the issue?

Share this post


Link to post
Share on other sites

I've just made the switch from Clover to OpenCore and generally everything is working great once it's booted. My only problem is that I use FileVault and my boot process seems to hang for anything from 20-60 seconds with the Apple logo on the screen before I'm asked for my password.

 

I've attached my OC debug log, the issue seems to be in this section:

 

04:091 00:003 OCABC: Only 187/256 slide values are usable!
04:095 00:003 OCABC: Valid slides - 0-167, 237-255
24:547 20:452 Trying XNU hook on System\Library\PrelinkedKernels\prelinkedkernel
24:561 00:013 Kext reservation size 7979008
25:340 00:779 Result of XNU hook on System\Library\PrelinkedKernels\prelinkedkernel is Success
25:356 00:015 OC: Read kernel version 19.2.0 (190200)

I'm using the OC Debug version with Target 83 verbose debugging, but nothing shows on the screen except that logo during the hang.

 

System: iMac17,1 - i7-6700k, Asus Z170 Pro w/ RX 580 GPU

opencore-2020-01-12-163735.txt

Share this post


Link to post
Share on other sites

@Mike Ranger, ForceBoost was broken at the time you tried it. It should be fixed now, but indeed I strongly do not recommend it, as it maxes frequency. The quirk is designed for specialised setups. The PCI patch is implemented in master, but we cannot test it.

 

@Sniki, generally we use WhateverGreen to disable discrete GPU. As for battery, I am afraid somebody else knows better.

 

@floodlitworld, this sounds like an older Dell issue. Please check UEFI → Input preferences. Perhaps playing with the timer resolution will improve the situation for you. Also make sure there are no conflicting UEFI drivers, just in case.

Edited by vit9696

Share this post


Link to post
Share on other sites
6 minutes ago, vit9696 said:

 

@floodlitworld, this sounds like an older Dell issue. Please check UEFI → Input preferences. Perhaps playing with the timer resolution will improve the situation for you. Also make sure there are no conflicting UEFI drivers, just in case.

 

I'm only running ApfsDriverLoader, FwRuntimeServices, HFSPlus and VirtualSmc in my drivers, so nothing I can drop there.

 

This is the config I'm running.

config.plist

 

I'm running a TimerResolution of 60000 since I have an ASUS motherboard.

Edited by floodlitworld

Share this post


Link to post
Share on other sites
33 minutes ago, vit9696 said:

@floodlitworld, try with 0. 60000 only applies to ASUS Z87 boards.

Tried 0, 10000, 40000, 50000, 60000 and 100000 and none seem to make much of a difference (10000 and 40000 took ages and sent me to a Reset Password Recovery menu).

Share this post


Link to post
Share on other sites

Not sure we can help with this. Does password menu appear quickly if you set KeySupport to NO? You may not be able to access OpenCore menu in this casem however.

Share this post


Link to post
Share on other sites
27 minutes ago, vit9696 said:

Not sure we can help with this. Does password menu appear quickly if you set KeySupport to NO? You may not be able to access OpenCore menu in this casem however.

Turned off KeySupport... didn't get to the screen any faster and my keyboard stopped working on the login screen too. Had to boot from USB to recover.

 

Seem to be getting diverted to the MacOS Password Recovery screen 9/10 boots now... System won't boot properly until I click the "Restart" button on the Password Recovery screen.

 

Shame... OC is working great once it gets me to that password screen.

Share this post


Link to post
Share on other sites

@vit9696... you did it!!!! with the latest quirk IncreasePciBarSize I can boot without a single kext / kernel patch needed anymore!!! This is outstanding!!!

Many thanks for your ongoing focus on execution! The last 4 weeks have brought so many improvements, and I am very impressed.

 

Best, Mike

 

Share this post


Link to post
Share on other sites

@floodlitworld, this issue sounds like some pretty serious issue in your firmware. Did you have it with Clover? Did you use AppleUiSupport driver with Clover? If not, does it work for you? Also, you have OpenCore Debug mentioned in your signature, does the issue happen with release builds as well?

Share this post


Link to post
Share on other sites
26 minutes ago, vit9696 said:

@floodlitworld, this issue sounds like some pretty serious issue in your firmware. Did you have it with Clover? Did you use AppleUiSupport driver with Clover? If not, does it work for you? Also, you have OpenCore Debug mentioned in your signature, does the issue happen with release builds as well?

No. It didn't happen with Clover. I did use AppleUISupport. My Clover EFI driver folder contained:

  1. ApfsDriverLoader
  2. AppleGenericInput
  3. AppleUISupport
  4. AptioMemoryFix
  5. HFSPlus
  6. UsbKbDxe
  7. VirtualSmc

Rebooted with the release version. It didn't go to password recovery this time and only stalled for about 15 seconds.... so better.

Is there anything else that could help? Reinstall BIOS firmware? Add extra drivers etc? Otherwise I'll just have to live with it. I don't restart more than once or twice a day. So it's not intolerable if it can't be fixed.

Share this post


Link to post
Share on other sites

I just saw the following, never really paid attention.....

 

Just before the picker menu is shown, is see a short message:

 

OCS: failed to parse data field of type 2

 

Since everything seems to work fine.... I closely checked the config.plist file again.... I could not find anything.

 

My question: is this something I should investigate... if yes... what could be the reason?

 

Thanks, Mike

 

Share this post


Link to post
Share on other sites

@floodlitworld, UsbKbDxe conflicts with AppleGenericInput in Clover. I would suggest you to remove it and check if there are any bugs.

 

As for OpenCore, could you try removing FwRuntimeServices? macOS will not boot, but it is interesting to see if that affects the situation anyhow. Also, I do not think your motherboard needs RequestBootVarRouting. In addition to that, I remember X99 boards had serious issues with hashing services, please set HashServices to YES.

 

@Mike Ranger, this means that some of the <data> fields in your configuration do not seem to be right. One can use OcSupportPkg/TestsUser/Serialized tool to debug configuration issues. Serialized.c contains the compilation command in the beginning of the file (clang -g -fsanitize=undefined,address …). Just compile it in Serialized directory and then pass your config.plist as an argument to see a verbose validation log.

 

Share this post


Link to post
Share on other sites

That compiling does not work for me.... all kinds of error of header files not found... after I copy them manually... all kinds of compiling errors...

Sorry.... I am not knowledgeable enough with these tools.

Mike

Share this post


Link to post
Share on other sites
40 minutes ago, vit9696 said:

@floodlitworld, UsbKbDxe conflicts with AppleGenericInput in Clover. I would suggest you to remove it and check if there are any bugs.

 

As for OpenCore, could you try removing FwRuntimeServices? macOS will not boot, but it is interesting to see if that affects the situation anyhow. Also, I do not think your motherboard needs RequestBootVarRouting. In addition to that, I remember X99 boards had serious issues with hashing services, please set HashServices to YES.

I haven't got the Clover install anymore, so I can't check on that one.

 

Tried out those things. Complete failure to boot without the RequestBootVarRouting and HashServices didn't make any difference.

 

Think I might just have to grin and bear this one. Thanks for your help anyway!

Share this post


Link to post
Share on other sites
1 hour ago, vit9696 said:

@floodlitworld, UsbKbDxe conflicts with AppleGenericInput in Clover. I would suggest you to remove it and check if there are any bugs.

 

As for OpenCore, could you try removing FwRuntimeServices? macOS will not boot, but it is interesting to see if that affects the situation anyhow. Also, I do not think your motherboard needs RequestBootVarRouting. In addition to that, I remember X99 boards had serious issues with hashing services, please set HashServices to YES.

 

@Mike Ranger, this means that some of the <data> fields in your configuration do not seem to be right. One can use OcSupportPkg/TestsUser/Serialized tool to debug configuration issues. Serialized.c contains the compilation command in the beginning of the file (clang -g -fsanitize=undefined,address …). Just compile it in Serialized directory and then pass your config.plist as an argument to see a verbose validation log.

 

If you delete FwRuntimeServices.efi then there will be a circle with a bevel line ->  -> circle with a bevel line -> 

 

RequestBootVarRouting --- I do not need

Thanks for OPENCORE

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   1 member

  • Similar Content

    • By SniperBuddy
      Hello guys,
      I'm relatively new to the world of hackintosh.
      I'm trying to install the latest Mac OS - Catalina with the help of Opencore, however, this is the error that's displayed while booting from the USB:
       
      https://drive.google.com/open?id=1Xd4V2wZ2fEsgRyfVcXlJHXMPGa85g2s3
       
      You can take a look at my config.plist file from here - https://drive.google.com/file/d/17FZpTcVp4RFSaxdm6yW4uELkt7MaLdmt/view?usp=sharing
       
      I'm using the Acer E575 G laptop with Kabylake (i5 7200u)
       
      Any help would be gladly appreciated!
       
      Edit: I've fixed this problem by following this guide completely - https://khronokernel-2.gitbook.io/opencore-vanilla-desktop-guide/intel-config.plist/kaby-lake
       
      This is due to OpenCore being unable to find any drives with the current ScanPolicy, setting to 0 will allow all boot options to be shown
       
       
       
       
       
       
       
    • By DanZiRuleZ
      Dear All, 
       
      trying to install Catalina on my ASUS Z87 Plus, I followed the Haswell guide to the letter, all set up now, USB stick boots ok, Catalina installs on SSD, but then when trying to boot it I am receiving Kernel Panic and no idea how to move forward. 
       
      Have the debug options, but opencore will only dump boot messages where I don't see much sticking out.
       
      My last resort would be just installing clover on the already installed SSD's EFI partition, it at all possible. High Sierra is working fine and I did get Clover with Mojave once but stuck with High Sierra with my GTX960 video card...
       
      Attached is the kernel panic and my EFI setup if anyone can help me troubleshoot.
      Many thanks
      D.
       

      EFI.zip
    • By n.d.k
      After several weeks of testing OC bootloader,  disecting its source code and also Clover's source code as well, I finally switch from Clover to OC as my main bootloader. Wait! don't get the wrong idea that OpenCore is better than Clover. They both work equally well, producing a bootable macOS as an end result with simliar boot time. OC design direction is different with Clover, I believe it's not intended as a Clover replacement, but more narrowing down to macOS specifically. However, macOS is not the only OS that i am using, so, i decided to add some minimal necessary source code modification to the OC to get some of the features I need. I like to share my customized OC forked https://github.com/n-d-k/OpenCorePkg , you have to compile it yourself if you want, i will not provide pre build binary.    
       
      Additional features/changes:
      ============
       
      [ Multi-Boot ]
        - ACPI patches are optional for non macOS with setting ACPI->Quirks->EnableForAll to yes (default is no).
        - Booter Quirtks, SMBIOS and Device Properties patches will only applied to macOS.
          
      [ Hotkeys ]
        - Full functional Hotkeys [1-9] corresponding to Boot Entry's Index number and dedicated W (Windows) / X (macOS) keys can be used without seeing Boot Picker.
        - While in boot picker, F10 can use to take a snapshot of the screen.
                
      [ Ui Boot Picker ]
        - Bios Date/time, auto boot to the same OS or manual set to always boot one OS mode, and OC version are displayed in boot picker.
        - Auto boot to previous booted OS (if Misc->Security->AllowSetDefault is NO/false).
        - macOS Recovery/Tools Entries are hidden by default, use Spacebar in Boot Menu as a toggle on/off to show/hide hidden entries.
                
      [ Custom Entries ]
         - Custom entries are now listed first in picker menu and by the orders they are appeared in Misc->Boot->Entries, before all other entries.
         - Ability to change entry name found by auto scanner by adding custom entry with the exact same device path,
           this will give users the option to complete change how all boot entries listed in Boot Picker.
          
      [ Others ]
         - No verbose apfs.efi driver loading (if using apfs.efi instead of ApfsDriverLoader.efi).
          - ndk-macbuild.tool script are set to compile with latest edk2 (One can easily set to stable edk2 if prefer).
          - NvmExpressDxe driver build script are also available for system without native nvme support. (Compatible with OC and Clover).
       
      Usage:
       - To build OpenCore, run "./ndk-macbuild.tool" at Terminal (require Xcode and Xcode Command Line Tool installed, and open xcode to accept license agreement before compiling).
       - To build NvmExpressDxe driver, run "./buildnvme.sh".
       
      4k screen resolutions

       
       

       
      Customized by @btwise

       
       
       
    • By Krani93
      Hi guys,
       
      I'm trying to install Catalina on a Lenovo m720q (i5-8600T with B360).
      After some other issues I'm know stuck at attached screen.
      Im using latest opencore version and have my EFI folder attached.
       
      Can someone help me I've got no clue what to try next :/ 
       
       
      Cheers!

      EFI.7z
    • By BlitzPanzer
      Catalina 10.15.3, OC 0.5.5

      Follow the OpenCore AMD Vanilla Guide, everything works fine iMessage, Siri, FaceTime, Continuity, Airdrop, Audio, WiFi
      But here is the problem
      Once I restart or shutdown and reboot, I will have kernel panic, so i have to reboot once again, then no more kernel panic, straight back to the system.
      Down below are the 3 kernel panic reports I got after I am back to the system, also provided specs, kexts, drivers and config.plist I used.
      Please someone help me with the problem
      Thanks in advanced   

      System Specs
      CPU: Ryzen R5 3600
      MOBO: MSI B450 Mortar Max
      RAM: Kingston HyperX Fury 16GB*2 3200MHz DDR4
      SSD: Kingston A2000 500GB NVMe PCIe
      GPU: Gigabyte RX 570 Gaming 4G v2.0
      PCIe: BCM943602CS Kexts:
      AppleALC
      AppleMCEReporterDisabler
      BrcmBluetoothInjector
      BrcmPatchRAM3
      HDMIAudio
      Lilu
      MacProMemoryNotificationDisabler
      NightShiftUnlocker
      NVMeFix
      RealtekRTL8111
      VirtualSMC
      WhateverGreen Drivers:
      ApfsDriverLoader
      AppleUsbKbDxe
      FwRuntimeServices
      VBoxHfs config.plist:
      https://drive.google.com/file/d/1M22Tvn7W-Zf_b_-J52oLcfjECj5qAcp6/view

      Kernel Panic Report 1
      panic(cpu 0 caller 0xffffff801b8652fa): Kernel trap at 0xffffff7f9f212fe3, type 14=page fault, registers: CR0: 0x000000008001003b, CR2: 0xffffffa3ce87c000, CR3: 0x00000000263ba000, CR4: 0x00000000003406e0 RAX: 0xffffffa3ce87c000, RBX: 0x0000000000005434, RCX: 0x0000000002000000, RDX: 0x0000000003000000 RSP: 0xffffffa3ce75bb60, RBP: 0xffffffa3ce75bb80, RSI: 0xffffff806d3141c0, RDI: 0x0000000000000000 R8: 0x0000000000000001, R9: 0x0000000000000026, R10: 0x00000000f8000000, R11: 0x0000000000000070 R12: 0xffffff805cc7c900, R13: 0xffffff835806f000, R14: 0x0000000000000000, R15: 0xffffff8068d2da50 RFL: 0x0000000000010246, RIP: 0xffffff7f9f212fe3, CS: 0x0000000000000008, SS: 0x0000000000000010 Fault CR2: 0xffffffa3ce87c000, Error code: 0x0000000000000002, Fault CPU: 0x0, PL: 0, VF: 1 Backtrace (CPU 0), Frame : Return Address 0xffffffa3ce75b5c0 : 0xffffff801b73bb2b mach_kernel : _handle_debugger_trap + 0x47b 0xffffffa3ce75b610 : 0xffffff801b8734d5 mach_kernel : _kdp_i386_trap + 0x155 0xffffffa3ce75b650 : 0xffffff801b864f4e mach_kernel : _kernel_trap + 0x4ee 0xffffffa3ce75b6a0 : 0xffffff801b6e2a40 mach_kernel : _return_from_trap + 0xe0 0xffffffa3ce75b6c0 : 0xffffff801b73b217 mach_kernel : _DebuggerTrapWithState + 0x17 0xffffffa3ce75b7c0 : 0xffffff801b73b5fb mach_kernel : _panic_trap_to_debugger + 0x21b 0xffffffa3ce75b810 : 0xffffff801bed2aa9 mach_kernel : _panic + 0x61 0xffffffa3ce75b880 : 0xffffff801b8652fa mach_kernel : _sync_iss_to_iks + 0x2aa 0xffffffa3ce75ba00 : 0xffffff801b864ff8 mach_kernel : _kernel_trap + 0x598 0xffffffa3ce75ba50 : 0xffffff801b6e2a40 mach_kernel : _return_from_trap + 0xe0 0xffffffa3ce75ba70 : 0xffffff7f9f212fe3 com.apple.kext.AMDRadeonX4000 : __ZN29AMDRadeonX4000_AMDHWRegisters4readEj + 0x53 0xffffffa3ce75bb80 : 0xffffff7f9f24a795 com.apple.kext.AMDRadeonX4000 : __ZN28AMDRadeonX4000_AMDVIHardware19getRegisterAperSizeEv + 0x23 0xffffffa3ce75bba0 : 0xffffff7f9f212ef0 com.apple.kext.AMDRadeonX4000 : __ZN29AMDRadeonX4000_AMDHWRegisters4initEP11IOPCIDeviceP30AMDRadeonX4000_IAMDHWInterface + 0xfa 0xffffffa3ce75bbe0 : 0xffffff7f9f2325c1 com.apple.kext.AMDRadeonX4000 : __ZN26AMDRadeonX4000_AMDHardware4initEP11IOPCIDeviceP28AMDRadeonX4000_IAMDHWHandlerRjP16_GART_PARAMETERSP14_FB_PARAMETERS + 0x257 0xffffffa3ce75bc30 : 0xffffff7f9f1b8adb com.apple.kext.AMDRadeonX4000 : __ZN37AMDRadeonX4000_AMDGraphicsAccelerator17createHWInterfaceEP11IOPCIDevice + 0x7b 0xffffffa3ce75bc70 : 0xffffff7f9f1b64be com.apple.kext.AMDRadeonX4000 : __ZN37AMDRadeonX4000_AMDGraphicsAccelerator15configureDeviceEP11IOPCIDevice + 0x10a 0xffffffa3ce75bd00 : 0xffffff7f9f128534 com.apple.iokit.IOAcceleratorFamily2 : __ZN22IOGraphicsAccelerator25startEP9IOService + 0x21e 0xffffffa3ce75bd80 : 0xffffff7f9f1b488e com.apple.kext.AMDRadeonX4000 : __ZN37AMDRadeonX4000_AMDGraphicsAccelerator5startEP9IOService + 0x82 0xffffffa3ce75bde0 : 0xffffff801be1b216 mach_kernel : __ZN9IOService14startCandidateEPS_ + 0xf6 0xffffffa3ce75be40 : 0xffffff801be1adc1 mach_kernel : __ZN9IOService15probeCandidatesEP12OSOrderedSet + 0xb21 0xffffffa3ce75bef0 : 0xffffff801be1a10e mach_kernel : __ZN9IOService14doServiceMatchEj + 0x2ce 0xffffffa3ce75bf50 : 0xffffff801be1c8ad mach_kernel : __ZN15_IOConfigThread4mainEPvi + 0x15d 0xffffffa3ce75bfa0 : 0xffffff801b6e213e mach_kernel : _call_continuation + 0x2e Kernel Extensions in backtrace: com.apple.iokit.IOAcceleratorFamily2(438.3.1)[66992525-3204-3CB0-8F03-4B70031B1CF2]@0xffffff7f9f0f0000->0xffffff7f9f1b2fff dependency: com.apple.driver.AppleMobileFileIntegrity(1.0.5)[A243D030-19AC-30AA-AC70-6C786DF9E6CE]@0xffffff7f9c185000 dependency: com.apple.iokit.IOPCIFamily(2.9)[ADD485B5-3EF8-37C4-B3C5-F86326E497A4]@0xffffff7f9c2f8000 dependency: com.apple.iokit.IOSurface(269.6)[42377B3B-D14A-368E-820F-07E7EA666198]@0xffffff7f9d454000 dependency: com.apple.iokit.IOGraphicsFamily(569.4)[1F9B5D88-52DB-3A16-8373-4F608A3CB2D8]@0xffffff7f9df73000 dependency: com.apple.iokit.IOReportFamily(47)[988360A2-2E10-3014-A119-BE81BC045A10]@0xffffff7f9c228000 com.apple.kext.AMDRadeonX4000(3.0.5)[5FD7AE5F-C03C-34A1-803F-ACA9B68524D0]@0xffffff7f9f1b3000->0xffffff7f9f6f7fff dependency: com.apple.iokit.IOPCIFamily(2.9)[ADD485B5-3EF8-37C4-B3C5-F86326E497A4]@0xffffff7f9c2f8000 dependency: com.apple.iokit.IOSurface(269.6)[42377B3B-D14A-368E-820F-07E7EA666198]@0xffffff7f9d454000 dependency: com.apple.iokit.IOGraphicsFamily(569.4)[1F9B5D88-52DB-3A16-8373-4F608A3CB2D8]@0xffffff7f9df73000 dependency: com.apple.iokit.IOAcceleratorFamily2(438.3.1)[66992525-3204-3CB0-8F03-4B70031B1CF2]@0xffffff7f9f0f0000 BSD process name corresponding to current thread: kernel_task Boot args: debug=0x100 keepsyms=1 alcid=1 -v shikigva=128 Mac OS version: 19D76 Kernel version: Darwin Kernel Version 19.3.0: Thu Jan 9 20:58:23 PST 2020; root:xnu-6153.81.5~1/RELEASE_X86_64 Kernel UUID: A8DDE75C-CD97-3C37-B35D-1070CC50D2CE Kernel slide: 0x000000001b400000 Kernel text base: 0xffffff801b600000 __HIB text base: 0xffffff801b500000 System model name: MacPro7,1 (Mac-27AD2F918AE68F61) System shutdown begun: NO Panic diags file available: NO (0xe00002bc) System uptime in nanoseconds: 47565362999  
      Kernel Panic Report 2
      panic(cpu 10 caller 0xffffff801b8652fa): Kernel trap at 0xffffff7f9e629fe3, type 14=page fault, registers: CR0: 0x000000008001003b, CR2: 0xffffff83d25d2000, CR3: 0x0000000029068000, CR4: 0x00000000003406e0 RAX: 0xffffff83d25d2000, RBX: 0x0000000000005434, RCX: 0x0000000002000000, RDX: 0x0000000003000000 RSP: 0xffffff83d14c3b60, RBP: 0xffffff83d14c3b80, RSI: 0xffffff805f6adb80, RDI: 0x0000000000000000 R8: 0x0000000000000001, R9: 0x0000000000000026, R10: 0x00000000f8000000, R11: 0x0000000000000070 R12: 0xffffff805fba2580, R13: 0xffffff835b02e000, R14: 0x0000000000000000, R15: 0xffffff80631191e0 RFL: 0x0000000000010246, RIP: 0xffffff7f9e629fe3, CS: 0x0000000000000008, SS: 0x0000000000000010 Fault CR2: 0xffffff83d25d2000, Error code: 0x0000000000000002, Fault CPU: 0xa, PL: 0, VF: 1 Backtrace (CPU 10), Frame : Return Address 0xffffff83d14c35c0 : 0xffffff801b73bb2b mach_kernel : _handle_debugger_trap + 0x47b 0xffffff83d14c3610 : 0xffffff801b8734d5 mach_kernel : _kdp_i386_trap + 0x155 0xffffff83d14c3650 : 0xffffff801b864f4e mach_kernel : _kernel_trap + 0x4ee 0xffffff83d14c36a0 : 0xffffff801b6e2a40 mach_kernel : _return_from_trap + 0xe0 0xffffff83d14c36c0 : 0xffffff801b73b217 mach_kernel : _DebuggerTrapWithState + 0x17 0xffffff83d14c37c0 : 0xffffff801b73b5fb mach_kernel : _panic_trap_to_debugger + 0x21b 0xffffff83d14c3810 : 0xffffff801bed2aa9 mach_kernel : _panic + 0x61 0xffffff83d14c3880 : 0xffffff801b8652fa mach_kernel : _sync_iss_to_iks + 0x2aa 0xffffff83d14c3a00 : 0xffffff801b864ff8 mach_kernel : _kernel_trap + 0x598 0xffffff83d14c3a50 : 0xffffff801b6e2a40 mach_kernel : _return_from_trap + 0xe0 0xffffff83d14c3a70 : 0xffffff7f9e629fe3 com.apple.kext.AMDRadeonX4000 : __ZN29AMDRadeonX4000_AMDHWRegisters4readEj + 0x53 0xffffff83d14c3b80 : 0xffffff7f9e661795 com.apple.kext.AMDRadeonX4000 : __ZN28AMDRadeonX4000_AMDVIHardware19getRegisterAperSizeEv + 0x23 0xffffff83d14c3ba0 : 0xffffff7f9e629ef0 com.apple.kext.AMDRadeonX4000 : __ZN29AMDRadeonX4000_AMDHWRegisters4initEP11IOPCIDeviceP30AMDRadeonX4000_IAMDHWInterface + 0xfa 0xffffff83d14c3be0 : 0xffffff7f9e6495c1 com.apple.kext.AMDRadeonX4000 : __ZN26AMDRadeonX4000_AMDHardware4initEP11IOPCIDeviceP28AMDRadeonX4000_IAMDHWHandlerRjP16_GART_PARAMETERSP14_FB_PARAMETERS + 0x257 0xffffff83d14c3c30 : 0xffffff7f9e5cfadb com.apple.kext.AMDRadeonX4000 : __ZN37AMDRadeonX4000_AMDGraphicsAccelerator17createHWInterfaceEP11IOPCIDevice + 0x7b 0xffffff83d14c3c70 : 0xffffff7f9e5cd4be com.apple.kext.AMDRadeonX4000 : __ZN37AMDRadeonX4000_AMDGraphicsAccelerator15configureDeviceEP11IOPCIDevice + 0x10a 0xffffff83d14c3d00 : 0xffffff7f9e52a534 com.apple.iokit.IOAcceleratorFamily2 : __ZN22IOGraphicsAccelerator25startEP9IOService + 0x21e 0xffffff83d14c3d80 : 0xffffff7f9e5cb88e com.apple.kext.AMDRadeonX4000 : __ZN37AMDRadeonX4000_AMDGraphicsAccelerator5startEP9IOService + 0x82 0xffffff83d14c3de0 : 0xffffff801be1b216 mach_kernel : __ZN9IOService14startCandidateEPS_ + 0xf6 0xffffff83d14c3e40 : 0xffffff801be1adc1 mach_kernel : __ZN9IOService15probeCandidatesEP12OSOrderedSet + 0xb21 0xffffff83d14c3ef0 : 0xffffff801be1a10e mach_kernel : __ZN9IOService14doServiceMatchEj + 0x2ce 0xffffff83d14c3f50 : 0xffffff801be1c8ad mach_kernel : __ZN15_IOConfigThread4mainEPvi + 0x15d 0xffffff83d14c3fa0 : 0xffffff801b6e213e mach_kernel : _call_continuation + 0x2e Kernel Extensions in backtrace: com.apple.iokit.IOAcceleratorFamily2(438.3.1)[66992525-3204-3CB0-8F03-4B70031B1CF2]@0xffffff7f9e4f2000->0xffffff7f9e5b5fff dependency: com.apple.driver.AppleMobileFileIntegrity(1.0.5)[A243D030-19AC-30AA-AC70-6C786DF9E6CE]@0xffffff7f9c3f1000 dependency: com.apple.iokit.IOPCIFamily(2.9)[ADD485B5-3EF8-37C4-B3C5-F86326E497A4]@0xffffff7f9c4a6000 dependency: com.apple.iokit.IOSurface(269.6)[42377B3B-D14A-368E-820F-07E7EA666198]@0xffffff7f9e4c1000 dependency: com.apple.iokit.IOGraphicsFamily(569.4)[1F9B5D88-52DB-3A16-8373-4F608A3CB2D8]@0xffffff7f9c793000 dependency: com.apple.iokit.IOReportFamily(47)[988360A2-2E10-3014-A119-BE81BC045A10]@0xffffff7f9c09f000 com.apple.kext.AMDRadeonX4000(3.0.5)[5FD7AE5F-C03C-34A1-803F-ACA9B68524D0]@0xffffff7f9e5ca000->0xffffff7f9eb0efff dependency: com.apple.iokit.IOPCIFamily(2.9)[ADD485B5-3EF8-37C4-B3C5-F86326E497A4]@0xffffff7f9c4a6000 dependency: com.apple.iokit.IOSurface(269.6)[42377B3B-D14A-368E-820F-07E7EA666198]@0xffffff7f9e4c1000 dependency: com.apple.iokit.IOGraphicsFamily(569.4)[1F9B5D88-52DB-3A16-8373-4F608A3CB2D8]@0xffffff7f9c793000 dependency: com.apple.iokit.IOAcceleratorFamily2(438.3.1)[66992525-3204-3CB0-8F03-4B70031B1CF2]@0xffffff7f9e4f2000 BSD process name corresponding to current thread: kernel_task Boot args: debug=0x100 keepsyms=1 alcid=1 -v shikigva=128 Mac OS version: 19D76 Kernel version: Darwin Kernel Version 19.3.0: Thu Jan 9 20:58:23 PST 2020; root:xnu-6153.81.5~1/RELEASE_X86_64 Kernel UUID: A8DDE75C-CD97-3C37-B35D-1070CC50D2CE Kernel slide: 0x000000001b400000 Kernel text base: 0xffffff801b600000 __HIB text base: 0xffffff801b500000 System model name: MacPro7,1 (Mac-27AD2F918AE68F61) System shutdown begun: NO Panic diags file available: NO (0xe00002bc) System uptime in nanoseconds: 38416992755  
      Kernel Panic Report 3
      panic(cpu 8 caller 0xffffff801da652fa): Kernel trap at 0xffffff7fa084dfe3, type 14=page fault, registers: CR0: 0x000000008001003b, CR2: 0xffffff83d44cd000, CR3: 0x000000002b260000, CR4: 0x00000000003406e0 RAX: 0xffffff83d44cd000, RBX: 0x0000000000005434, RCX: 0x0000000002000000, RDX: 0x0000000003000000 RSP: 0xffffff83d319bb60, RBP: 0xffffff83d319bb80, RSI: 0xffffff8066659c00, RDI: 0x0000000000000000 R8: 0x0000000000000001, R9: 0x0000000000000026, R10: 0x00000000f8000000, R11: 0x0000000000000070 R12: 0xffffff8061f35280, R13: 0xffffff835d231000, R14: 0x0000000000000000, R15: 0xffffff806189db90 RFL: 0x0000000000010246, RIP: 0xffffff7fa084dfe3, CS: 0x0000000000000008, SS: 0x0000000000000000 Fault CR2: 0xffffff83d44cd000, Error code: 0x0000000000000002, Fault CPU: 0x8, PL: 0, VF: 1 Backtrace (CPU 8), Frame : Return Address 0xffffff83d319b5c0 : 0xffffff801d93bb2b mach_kernel : _handle_debugger_trap + 0x47b 0xffffff83d319b610 : 0xffffff801da734d5 mach_kernel : _kdp_i386_trap + 0x155 0xffffff83d319b650 : 0xffffff801da64f4e mach_kernel : _kernel_trap + 0x4ee 0xffffff83d319b6a0 : 0xffffff801d8e2a40 mach_kernel : _return_from_trap + 0xe0 0xffffff83d319b6c0 : 0xffffff801d93b217 mach_kernel : _DebuggerTrapWithState + 0x17 0xffffff83d319b7c0 : 0xffffff801d93b5fb mach_kernel : _panic_trap_to_debugger + 0x21b 0xffffff83d319b810 : 0xffffff801e0d2aa9 mach_kernel : _panic + 0x61 0xffffff83d319b880 : 0xffffff801da652fa mach_kernel : _sync_iss_to_iks + 0x2aa 0xffffff83d319ba00 : 0xffffff801da64ff8 mach_kernel : _kernel_trap + 0x598 0xffffff83d319ba50 : 0xffffff801d8e2a40 mach_kernel : _return_from_trap + 0xe0 0xffffff83d319ba70 : 0xffffff7fa084dfe3 com.apple.kext.AMDRadeonX4000 : __ZN29AMDRadeonX4000_AMDHWRegisters4readEj + 0x53 0xffffff83d319bb80 : 0xffffff7fa0885795 com.apple.kext.AMDRadeonX4000 : __ZN28AMDRadeonX4000_AMDVIHardware19getRegisterAperSizeEv + 0x23 0xffffff83d319bba0 : 0xffffff7fa084def0 com.apple.kext.AMDRadeonX4000 : __ZN29AMDRadeonX4000_AMDHWRegisters4initEP11IOPCIDeviceP30AMDRadeonX4000_IAMDHWInterface + 0xfa 0xffffff83d319bbe0 : 0xffffff7fa086d5c1 com.apple.kext.AMDRadeonX4000 : __ZN26AMDRadeonX4000_AMDHardware4initEP11IOPCIDeviceP28AMDRadeonX4000_IAMDHWHandlerRjP16_GART_PARAMETERSP14_FB_PARAMETERS + 0x257 0xffffff83d319bc30 : 0xffffff7fa07f3adb com.apple.kext.AMDRadeonX4000 : __ZN37AMDRadeonX4000_AMDGraphicsAccelerator17createHWInterfaceEP11IOPCIDevice + 0x7b 0xffffff83d319bc70 : 0xffffff7fa07f14be com.apple.kext.AMDRadeonX4000 : __ZN37AMDRadeonX4000_AMDGraphicsAccelerator15configureDeviceEP11IOPCIDevice + 0x10a 0xffffff83d319bd00 : 0xffffff7fa074e534 com.apple.iokit.IOAcceleratorFamily2 : __ZN22IOGraphicsAccelerator25startEP9IOService + 0x21e 0xffffff83d319bd80 : 0xffffff7fa07ef88e com.apple.kext.AMDRadeonX4000 : __ZN37AMDRadeonX4000_AMDGraphicsAccelerator5startEP9IOService + 0x82 0xffffff83d319bde0 : 0xffffff801e01b216 mach_kernel : __ZN9IOService14startCandidateEPS_ + 0xf6 0xffffff83d319be40 : 0xffffff801e01adc1 mach_kernel : __ZN9IOService15probeCandidatesEP12OSOrderedSet + 0xb21 0xffffff83d319bef0 : 0xffffff801e01a10e mach_kernel : __ZN9IOService14doServiceMatchEj + 0x2ce 0xffffff83d319bf50 : 0xffffff801e01c8ad mach_kernel : __ZN15_IOConfigThread4mainEPvi + 0x15d 0xffffff83d319bfa0 : 0xffffff801d8e213e mach_kernel : _call_continuation + 0x2e Kernel Extensions in backtrace: com.apple.iokit.IOAcceleratorFamily2(438.3.1)[66992525-3204-3CB0-8F03-4B70031B1CF2]@0xffffff7fa0716000->0xffffff7fa07d9fff dependency: com.apple.driver.AppleMobileFileIntegrity(1.0.5)[A243D030-19AC-30AA-AC70-6C786DF9E6CE]@0xffffff7f9e5f1000 dependency: com.apple.iokit.IOPCIFamily(2.9)[ADD485B5-3EF8-37C4-B3C5-F86326E497A4]@0xffffff7f9e6a6000 dependency: com.apple.iokit.IOSurface(269.6)[42377B3B-D14A-368E-820F-07E7EA666198]@0xffffff7fa06e5000 dependency: com.apple.iokit.IOGraphicsFamily(569.4)[1F9B5D88-52DB-3A16-8373-4F608A3CB2D8]@0xffffff7f9e993000 dependency: com.apple.iokit.IOReportFamily(47)[988360A2-2E10-3014-A119-BE81BC045A10]@0xffffff7f9e29f000 com.apple.kext.AMDRadeonX4000(3.0.5)[5FD7AE5F-C03C-34A1-803F-ACA9B68524D0]@0xffffff7fa07ee000->0xffffff7fa0d32fff dependency: com.apple.iokit.IOPCIFamily(2.9)[ADD485B5-3EF8-37C4-B3C5-F86326E497A4]@0xffffff7f9e6a6000 dependency: com.apple.iokit.IOSurface(269.6)[42377B3B-D14A-368E-820F-07E7EA666198]@0xffffff7fa06e5000 dependency: com.apple.iokit.IOGraphicsFamily(569.4)[1F9B5D88-52DB-3A16-8373-4F608A3CB2D8]@0xffffff7f9e993000 dependency: com.apple.iokit.IOAcceleratorFamily2(438.3.1)[66992525-3204-3CB0-8F03-4B70031B1CF2]@0xffffff7fa0716000 BSD process name corresponding to current thread: kernel_task Boot args: debug=0x100 keepsyms=1 alcid=1 -v shikigva=128 Mac OS version: 19D76 Kernel version: Darwin Kernel Version 19.3.0: Thu Jan 9 20:58:23 PST 2020; root:xnu-6153.81.5~1/RELEASE_X86_64 Kernel UUID: A8DDE75C-CD97-3C37-B35D-1070CC50D2CE Kernel slide: 0x000000001d600000 Kernel text base: 0xffffff801d800000 __HIB text base: 0xffffff801d700000 System model name: MacPro7,1 (Mac-27AD2F918AE68F61) System shutdown begun: NO Panic diags file available: NO (0xe00002bc) System uptime in nanoseconds: 27776834167  
      config.plist
×