Jump to content
glasgood

Glasgood's macOS Mojave [SUCCESS][GUIDE] for Aorus Z390 Pro

1,471 posts in this topic

Recommended Posts

9 hours ago, larabee said:

I used your pre-installation EFI as both my Pre and Post installation. I don't need to do anything with SSDT for my USB to work because my board is within the USB limit of Mac OS. Besides, the USB patch from config.plist already unlocked the USB 3 ports. Everything went as smoothly as it should on a real Mac. 

I'm still tweaking the voltage of my Vega 56 to make it runs a bit cooler.

 

 

Was just looking at your board.  Do you have a WiFi card with Bluetooth connected to F_USB header, also is F_USB30 attached to CASE, those USB ports on CASE could exceed the limit. 

 

1643816610_Screenshot2019-04-22at07_26_46.png.c4ddc378668df1611f491bfd8c7ba486.png

 

 

If in doubt, try a port discovery,  see guide below:

 

 

Thanks for letting me know that EFI pre-installation worked on your machine. 

 

 

 

 

Share this post


Link to post
Share on other sites
Advertisement
Posted (edited)
15 hours ago, glasgood said:

 

Hi, 

 

I got two hard drives for my machine, one  for testing. I noticed that Country Code was set US on the test drive, as far as I was aware it should be GB or DE.  As far as I know, AirportBrcmFixup.kext for my Wi-Fi card defaults to US, so I found the way to change country code. I updated guide with instructions on this. 

 

OPTIONAL: Set Wi-Fi Country Code

 

 

 

Resolved the issue, finally.  Regarding the speed problem with the BCM94360CD, this is where some of my inexperience shows up, after trying varying ways to get my 5GHz band working as it should, stopping the high pings and complete slowing down of my connection to a crawl, etc.  I reseated the card, rebooted my router, still no avail, then I realized I had overlooked placing the AirportBrcmFixup.kext into my Other folder on my EFI partition.  I guess I thought this card just worked out of the box so it didn't occur to me.  Once the kext was installed, and I rebooted my speed went way up where it should be normally.  And more importantly stayed there. Now to change the country code. :)

Edited by Hifi33

Share this post


Link to post
Share on other sites
16 hours ago, glasgood said:

 

Was just looking at your board.  Do you have a WiFi card with Bluetooth connected to F_USB header, also is F_USB30 attached to CASE, those USB ports on CASE could exceed the limit. 

 

If in doubt, try a port discovery,  see guide below:

 

 

Thanks for letting me know that EFI pre-installation worked on your machine. 

 

 

I don't use any of those connectors and stay within the USB limit. I tried hooking up my case USB ports and my Monitor USB ports into the USB 3 headers on my board and confirm they are all working just fine (I did not measure the bandwidth of them anyway) 

I think it's because I have the USB patches applied?  

489097579_ScreenShot2019-04-22at4_01_18PM.thumb.png.719806964222cf493241c96c91ba16ce.png

 

I will install a thunderbolt add-on card from Gigabyte soon.

What Wifi card do you recommend for airdrop? 

 

Share this post


Link to post
Share on other sites
7 hours ago, larabee said:

 

I don't use any of those connectors and stay within the USB limit. I tried hooking up my case USB ports and my Monitor USB ports into the USB 3 headers on my board and confirm they are all working just fine (I did not measure the bandwidth of them anyway) 

I think it's because I have the USB patches applied?  

 

I will install a thunderbolt add-on card from Gigabyte soon.

What Wifi card do you recommend for airdrop? 

 

 

 

Sometime when macOS is updated it can beak the ports limit patch, and RehabMan mentioned " The port limit patch should not be used as a permanent solution. There is now clear evidence that using it causes other data beyond what is evidently a fixed size array to be clobbered. The result is strange behavior by the USB drivers when the port limit is exceeded." Pointer >> USB ports limit etc..

 

RECOMMENDED WIFI CARD → ABWB 802.11AC WI-FI With Bluetooth 4.0 PCI-Express (PCI-E) BCM943602CS  

 

:)

 

 

Share this post


Link to post
Share on other sites
Posted (edited)
14 hours ago, glasgood said:

 

 

Sometime when macOS is updated it can beak the ports limit patch, and RehabMan mentioned " The port limit patch should not be used as a permanent solution. There is now clear evidence that using it causes other data beyond what is evidently a fixed size array to be clobbered. The result is strange behavior by the USB drivers when the port limit is exceeded." Pointer >> USB ports limit etc..

  

RECOMMENDED WIFI CARD → ABWB 802.11AC WI-FI With Bluetooth 4.0 PCI-Express (PCI-E) BCM943602CS  

 

:)

 

 

Thank you so much, I will get my SSDT at a later point because I'm on mission critical using that hackintosh (it's stable enough.) I've had other builds that eject USB randomly when the max ports are reached.

I've just ordered one of the BCM943602CS card for cheap like $20 including the PCIExpress X1 adapter. 

ULB8IhGHKRahduJk43Jaq6zM8FXaG.jpg

 

UPDATED: 
I've removed some ports in my SSDT. Here is my Board Layout with USB ports mapped

 

1643816610_Screenshot2019-04-22at07_26_46.png.c4ddc378668df1611f491bfd8c7ba486.png.4b37585d15f842fd90e96bc824295f30.png

 

The included SSDT completely disabled 5+6 ports. 

 

 

SSDT-UIAC.aml

Edited by larabee
add SSDT

Share this post


Link to post
Share on other sites
16 hours ago, larabee said:

 

UPDATED: 
I've removed some ports in my SSDT. Here is my Board Layout with USB ports mapped

 

1643816610_Screenshot2019-04-22at07_26_46.png.c4ddc378668df1611f491bfd8c7ba486.png.4b37585d15f842fd90e96bc824295f30.png

 

The included SSDT completely disabled 5+6 ports. 

 

 

SSDT-UIAC.aml

 

 

Above will be handy for other users who have Z390 Gaming X :thumbsup_anim: thanks!

 

Share this post


Link to post
Share on other sites
On 4/10/2019 at 5:33 AM, glasgood said:

 

tbh i'm not sure as I don't have the  i7 9700K, I tried a quick test and changed to iMac 19,1 SMBIOS but on boot got an unsupported macOS error, use previous EFI from guide and you can easily provide the missing CPU info. See "About My Mac" in my other guide on how to do this: 

 

 

 

 

 

I have been attempting to change this for my i7 9700k, as well, to 19,1 iMac without much luck.  The unsupported macOS error.  I am a little confused what was meant by use previous EFI in your post.  Was that to get past the "unsupported" boot error or was that only to edit the About My Mac section?  (The AMM guide worked great. :))   I have searched for a solution, and nothing online has been successful for me so far.

Share this post


Link to post
Share on other sites
Posted (edited)
9 hours ago, Hifi33 said:

I have been attempting to change this for my i7 9700k, as well, to 19,1 iMac without much luck.  The unsupported macOS error.  I am a little confused what was meant by use previous EFI in your post.  Was that to get past the "unsupported" boot error or was that only to edit the About My Mac section?  (The AMM guide worked great. :))   I have searched for a solution, and nothing online has been successful for me so far.

 

Hi Hifi33

 

As far as I am aware, new iMac 19,1 SMBIOS requires a special build of macOS Mojave, hence the unsupported macOS error when using SMBIOS 19,1.  In meantime, change "Unknown CPU in About My Mac " see my previous guide link below:

 

Update

 

SMBIOS support for 19,1 in Mojave 10.14.5 beta.

 

 

 

 

 

 

 

 

Edited by glasgood

Share this post


Link to post
Share on other sites
2 hours ago, glasgood said:

Possibly going to be supported in Mojave 10.14.5

 

 

 

 

I've tried the beta build and go through without any issue using iMac 19,1 SMBIOS, but things are a little unstable (not sure if it's because hackintosh or a beta build) 

Share this post


Link to post
Share on other sites
Posted (edited)
7 hours ago, larabee said:

 

I've tried the beta build and go through without any issue using iMac 19,1 SMBIOS, but things are a little unstable (not sure if it's because hackintosh or a beta build) 

 

Thanks, good to know. I expect that Clover, kext updates etc.. will smooth things out in 10.14.5 

 

Edited by glasgood

Share this post


Link to post
Share on other sites

@glasgood 

I used the SMBios iMac 18.3 and whenever I export using Final Cut pro + H264 format, the hackintosh completely freezes.

Can you help me out? 

Share this post


Link to post
Share on other sites
Posted (edited)
2 hours ago, larabee said:

@glasgood 

I used the SMBios iMac 18.3 and whenever I export using Final Cut pro + H264 format, the hackintosh completely freezes.

Can you help me out? 

 

Please attach your EFI folder. I’m using SMBIOS for Mac Mini 2018 and FCP is working. 

 

I’m meantime, check BIOS settings are set for:

 

Chipset  Internal Graphics  Enabled

Peripherals  Initial Display Output  PCIe 1 Slot

Chipset  DVMT Pre-Allocated  64M ( try 128 ) 

 

 

 

 

Edited by glasgood

Share this post


Link to post
Share on other sites
9 minutes ago, glasgood said:

 

Please attach your EFI folder. I’m using SMBIOS for Mac Mini 2018 and FCP is working. 

 

I’m meantime, check BIOS settings are set for:

 

Chipset  Internal Graphics  Enabled

 Peripherals  Initial Display Output  PCIe 1 Slot

Chipset  DVMT Pre-Allocated  64M ( try 128 ) 

 

 

 

 

Thanks a lot for your response. I used the same EFI as yours. It's working fine but whenever I export using H264 it freezes up. Exporting using Apple Pro Res is fine. 

Even  though other softwares report that Hardware Encoding is supported. 

 956345402_ScreenShot2019-04-30at10_37_20PM.png.99506d3f8850d3933f607372d43db596.png

637880445_ScreenShot2019-04-30at10_38_07PM.png.8cd878923f404ed1927b9b586f6277f3.png

 

Updated: 

I managed to get it to export H264 but it's still slower than a real mac by a large margin by  ticking Load VBios and Inject Intel then add 0x3E920003 to ig-platform-id in Graphics 

Then Adobe Media Encoder and FCPX starts using the iGPU to encode H264 

 

107639762_ScreenShot2019-04-30at10_33_38PM.png.8004c9ee861bc237fb1074b5d1b11a9d.png

 

 

Share this post


Link to post
Share on other sites
Posted (edited)
3 hours ago, larabee said:

 

 956345402_ScreenShot2019-04-30at10_37_20PM.png.99506d3f8850d3933f607372d43db596.png

 

 

 

 

 

 

 

 

Just wondering why you'r macx-video reports 27" (iMac Mid 2017) with an image of a Mac Mini. I ran macx-video on my hack and Hardware Info is normal. 

 

207649688_Screenshot2019-05-01at10_50_15.thumb.png.2ceb8d50ec9924c51461071e8145c51a.png

 

 

 

 

Edited by glasgood

Share this post


Link to post
Share on other sites

Glasgood, have you kept EmuVariableUEFI-64.efi off your system? I removed it to try and clear up the memory allocation error on reboot and today iMessages suddenly stopped working, so I put it back. Just a heads up in case anybody else runs into the same issue. 

Share this post


Link to post
Share on other sites
Posted (edited)
32 minutes ago, ppohio said:

Glasgood, have you kept EmuVariableUEFI-64.efi off your system? I removed it to try and clear up the memory allocation error on reboot and today iMessages suddenly stopped working, so I put it back. Just a heads up in case anybody else runs into the same issue. 

 

Hello,

 

EmuVariableUEFI-64.efi is only needed to activate iMessage's, once you have iMessage's working you can delete EmuVariableUEFI-64.efi. If you persist with EmuVariableUEFI-64.efi after you have activated iMessage's you will have intermittent memory allocation errors. 

 

Just to be clear on this

 

Step 1

 

Place EmuVariableUEFI-64.efi inside EFI /Clover /Drivers shutdown and restart machine. 

 

Step 2

 

Then login to iMessage's, Facetime, icloud and then mount EFI partition and delete 

EmuVariableUEFI-64.efi. 

 

Step 3

 

Then shutdown and restart machine

 

Step 4 

 

Test iMessage's, Facetime ( Will be working without EmuVariableUEFI-64.efi)

 

------------------------------------

 

Sometimes if you make changes to your hackintosh EFI folder, you may have to reactivate iMessage's. 

 

 

Best!

 

Edited by glasgood

Share this post


Link to post
Share on other sites
6 hours ago, glasgood said:

 

 

Just wondering why you'r macx-video reports 27" (iMac Mid 2017) with an image of a Mac Mini. I ran macx-video on my hack and Hardware Info is normal. 

  

 

 

I followed your guide and choose mac mini because it uses the coffee lake processor just like mine. Everything works fine but I have problem with H264 hardware encoding. 

I tried the iMac and it works. I think adding 0x3E920003 to ig-platform-id makes it works. 

Share this post


Link to post
Share on other sites

Thank you very much! I've followed your guide and everything is working like a charm!

 

This is my first desktop Hackintosh and with your guide it was pretty straightforward :)

 

My build:

- Gigabyte Aorus Z390 Pro

- Intel i5-8400 (leaving space for future upgrades)

- 2x Crucial Ballistic Sport Lt 8GB

- Kingston A400 SSD Sata3 (Hackintosh)

- Adata XPG Gammix S10 M.2 PCIe SSD. (Windows 10)

- Thermaltake Tt V200 and Thermaltake Smart RGB 600w PSU

- TP-Link AC1900 Archer T9e Wi-Fi

- Using iGPU because I'm still waiting for the GPU to arrive (Sapphire Pulse RX580 8GB)

 

One comment: The XPG Gammix S10 M.2 PCIe SSD DIDN'T WORK OK for MacOS. After installation (that took a while) my mouse was laggy every time I copied a file. Did a Benchmark with Blackmagic and found that the SSD was running as low as 40 MB/s for reading...

Tested with another partition in Windows and was working correctly (like 1500MB/s), so I changed the Mac installation to the SATA drive and the Windows to the M.2.

Second comment: I've tested FHD video editing with integrated graphics and was pretty surprised how well it did to manage everything.

 

Big thanks from Argentina!

Share this post


Link to post
Share on other sites
1 hour ago, mfortuna said:

Thank you very much! I've followed your guide and everything is working like a charm!

 

This is my first desktop Hackintosh and with your guide it was pretty straightforward :)

 

My build:

- Gigabyte Aorus Z390 Pro

- Intel i5-8400 (leaving space for future upgrades)

- 2x Crucial Ballistic Sport Lt 8GB

- Kingston A400 SSD Sata3 (Hackintosh)

- Adata XPG Gammix S10 M.2 PCIe SSD. (Windows 10)

- Thermaltake Tt V200 and Thermaltake Smart RGB 600w PSU

- TP-Link AC1900 Archer T9e Wi-Fi

- Using iGPU because I'm still waiting for the GPU to arrive (Sapphire Pulse RX580 8GB)

 

One comment: The XPG Gammix S10 M.2 PCIe SSD DIDN'T WORK OK for MacOS. After installation (that took a while) my mouse was laggy every time I copied a file. Did a Benchmark with Blackmagic and found that the SSD was running as low as 40 MB/s for reading...

Tested with another partition in Windows and was working correctly (like 1500MB/s), so I changed the Mac installation to the SATA drive and the Windows to the M.2.

Second comment: I've tested FHD video editing with integrated graphics and was pretty surprised how well it did to manage everything.

 

Big thanks from Argentina!

 

Thanks for taking the time to share your progress, I really appreciate that. I'm happy your first desktop hackintosh build has been pretty straightforward.

 

 :thumbsup_anim:

 

Share this post


Link to post
Share on other sites

Hey man,

 

I have a problem with my USB ports when booting into macOS with the internal SSD. Both my mouse and keyboard aren't being picked up, but when booting through the USB installer it's completely fine. Have any suggestions? Thanks.

Share this post


Link to post
Share on other sites
Posted (edited)
3 hours ago, yegtrash said:

Hey man,

 

I have a problem with my USB ports when booting into macOS with the internal SSD. Both my mouse and keyboard aren't being picked up, but when booting through the USB installer it's completely fine. Have any suggestions? Thanks.

 

Do you have Aorus Z390 Pro motherboard?  I suspect not.  My SSDT mapping for Aorus Z390 has disabled those USB ports on your motherboard. Remove SSDT from Clover / ACPI / Patched.

 

PRE-INSTALL Aorus Pro Z390 EFI ( USB Installer )  has no SSDT for USB ports fix. Thats why you have working USB ports via ports limit patch & USBInjectAll.kext using USB installer. 

 

POST-INSTALL Aorus Pro Z390 EFI, it has SSDT for USB ports fix. 

 

Hence why I suspect you have a different motherboard.  Delete SSDT-UIAC.aml from Clover / ACPI / PAtched and follow guide below for USB ports fix.

 

 

 

 

524277149_Screenshot2019-05-05at11_11_11.thumb.png.93ead065846a0ad1bff6847b6b077d96.png

 

 

 

Edited by glasgood

Share this post


Link to post
Share on other sites
5 hours ago, glasgood said:

 

Do you have Aorus Z390 Pro motherboard?  I suspect not.  My SSDT mapping for Aorus Z390 has disabled those USB ports on your motherboard. Remove SSDT from Clover / ACPI / Patched.

 

PRE-INSTALL Aorus Pro Z390 EFI ( USB Installer )  has no SSDT for USB ports fix. Thats why you have working USB ports via ports limit patch & USBInjectAll.kext using USB installer. 

 

POST-INSTALL Aorus Pro Z390 EFI, it has SSDT for USB ports fix. 

 

Hence why I suspect you have a different motherboard.  Delete SSDT-UIAC.aml from Clover / ACPI / PAtched and follow guide below for USB ports fix.

 

 

 

 

524277149_Screenshot2019-05-05at11_11_11.thumb.png.93ead065846a0ad1bff6847b6b077d96.png

 

 

 

I do indeed have the exact motherboard you have, Z390 Aorus Pro. I did my own custom USB map but for some reason, it just disables all of the USB ports when I boot directly from my SSD.

Share this post


Link to post
Share on other sites
Posted (edited)
13 minutes ago, yegtrash said:

I do indeed have the exact motherboard you have, Z390 Aorus Pro. I did my own custom USB map but for some reason, it just disables all of the USB ports when I boot directly from my SSD.

 

I have other SSDT's with different port mappings attached at bottom of guide. Give them a try. 

Edited by glasgood

Share this post


Link to post
Share on other sites
On 5/2/2019 at 1:12 AM, mfortuna said:

- Using iGPU because I'm still waiting for the GPU to arrive (Sapphire Pulse RX580 8GB Sapphire Nitro+ RX 590 SE) 

 

Finally arrived!

 

I've found a brand new Sapphire Nitro+ RX590 SE cheaper than the 580 and plugged it in:

 

I've had an issue with my monitor...It's a quite old LED monitor with only VGA connector. Previously I was using a passive adapter to HDMI. When I connected this to the Sapphire GPU it just restarted my PC, both in hackintosh or windows. After that I attached my livingroom TV that has hdmi inputs and it worked normally. 

 

Do you know if there's an adapter that may work?

 

Since it is an RX 590 should I use your same clover made for RX 580?

 

Thank you very much!

Share this post


Link to post
Share on other sites
14 minutes ago, mfortuna said:

 

Finally arrived!

 

I've found a brand new Sapphire Nitro+ RX590 SE cheaper than the 580 and plugged it in:

 

I've had an issue with my monitor...It's a quite old LED monitor with only VGA connector. Previously I was using a passive adapter to HDMI. When I connected this to the Sapphire GPU it just restarted my PC, both in hackintosh or windows. After that I attached my livingroom TV that has hdmi inputs and it worked normally. 

 

Do you know if there's an adapter that may work?

 

Since it is an RX 590 should I use your same clover made for RX 580?

 

Thank you very much!

 

Hi,

Unfortunately I don’t have recommendations for adapters. Clover folder should be good for RX590.

Share this post


Link to post
Share on other sites
Guest
This topic is now closed to further replies.

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By AudioGod
      I have put together this simple little guide for anybody wanting to use a Patched DSDT EFI with the same configuration as me.
      This is also a thread to discuss everything Z390 Pro and try and help where we can and maybe make things a little better for you. 
       
      A huge massive thank you to @glasgood @MaLd0n @larabee These three guys have helped me and talked me so much and are as helpful as you could ever get, Without them I wouldn't have a perfect working build like I do or be putting up this Guide & Discussion Thread sharing the hard work and countless hours that we have all put in to this.   
       
       
      This EFI and Patched DSDT have been created to work with a Gigabyte Aorus Z390 Pro, 9900k with a Vega 56 but has also been tested and verified fully working with the following Hardware
       
      CPU's
      8700k, 9700k, 9900k
       
      GPU's
      RX 580, Vega 56, Vega 64, Radion VII
      (If you have success with any different CPU or GPU's then please do let me know)
       
       
      There Is No Better Guide Then The One That @glasgood Has Already Written So Just Follow He's Guide For a Perfect Install.     
       
       
      HARDWARE USED
      • Intel I9 9900k 
      • Gigabyte AORUS Z390 PRO
      • Sapphire Pulse Vega 56 ( connected to monitor with DisplayPort )
      • Corsair Vengeance Pro RGB 16GB @3200mhz (2 x 8GB)
      • Corsair RM850x 80 Plus Gold Power Supply Unit
      • Coolermaster MASTERLIQUID ML360R RGB CPU Cooler
      • Samsung 860 EVO 500GB SSD (2.5) macOS Mojave
      • Samsung 860 EVO 1TB SSD (2.5) Windows 10 Pro
      • ABWB BCM943602CS 802.11AC WI-FI With Bluetooth 4.0 PCI-Express (PCI-E)   
      • Lian Li PC-O11DW Dynamic ATX Case
       

       

       
       
      WORKING
      • Sound 
      • Ethernet Port
      • WiFi
      • SSD Trim
      • USB 3.0 & 2.0 
      • AirDrop
      • iCloud
      • Hardware Acceleration AMD RX 580 / AMD Vega
      • iMessages
      • Facetime
      • Handoff
      • Netflix on Safari browser
      • Continuity
       
       
      CLOVER  FOLDER
      Use this folder with fully patched DSDT
      Z390 Pro DSDT EFI.zip   (Updated 21 July 2019)
       
       
      If Your Not Using File Vault Then Please Disable Hibernate
      disablehibernate.command
       
       
      To Create Your Own Patched DSDT Message @MaLd0n using the link bellow
      https://olarila.com/forum/viewtopic.php?f=19&t=1131 
      (If you want a perfect setup then getting your own patched DSDT made would be the best thing to do, Mine will work perfectly fine but different hardware no matter how small a change it is can tend to have some sort of effect on the DSDT and your setup)
       
       
      BIOS SETTINGS (Bios Revision F10)
       
      • Enter BIOS → Press F12 → Enter Setup
      • Save & Exit → Load Optimized Defaults
       
      • BIOS → Windows 8/10 Features → Other OS
      • BIOS → CSM Support → Disabled  
       
      • MIT → Advanced Memory Settings  → Extreme Memory Profile (X.M.P) → Enabled  
       
      • Peripherals → Initial Display Output → PCIe 1 Slot
      • Peripherals → Trusted Computing → Security Device Support →  Disable
      • Peripherals → Intel(R)Bios Guard → Intel BIOS Guard Support →  Disable
      • Peripherals → USB Configuration → Legacy USB Support →  Enabled
      • Peripherals → USB Configuration → XHCI Hand-off →  Enabled
      • Peripherals → Network Stack Configuration → Network Stack →  Disabled
      • Peripherals → SATA And RST Configuration → SATA Mode Selection →  AHCI
       
      • Chipset → Vt-d → Enabled  (can be enabled or disabled, your choice)
      • Chipset → Internal Graphics → Disabled
      • Chipset → Audio Controller → Enabled
      • Chipset → Above 4G Decoding → Disabled 
       
      • Power → Platform Power Management → Enabled
      • Power → ErP → Enabled  (can be enabled or disabled, your choice)
      • Power → RC6 (Render Standby) → Disabled
       
      • Save & Exit → Save & Exit Setup
       
       
      SCREENSHOTS
       

       

       

       

       

       

       

       

       

       

       

       

    • By Pedro Diniz
      Hello Friends, how are ya?

      Could you help me with a problem?

      I followed some guides like: https://www.insanelymac.com/forum/topic ... coffeelake -dsdt /

      and the installation of high Sierra 10.13.6 (17G8030) and nvidia webdrivers (correspondent to OS version) went smoothly, the problem starts when I try to boot the GPU.

      Hardware:
      MOBO: Aorus B360M gaming 3 (rev.1)
      CPU: i5 8400
      GPU: GTX 1060 OC Galax redblack

      BIOS:
      Fast boot - disabled
      windows 8/10 features - other os
      lan pxe - disabled
      storage boot option - UEFI
      other pci devices - UEFI
       
      Initial display output - PCie 1 slot
      Intel's Platform Trust Technology (PTT) - disabled
      sata mode selection - AHCI
      XHCI hand off - enabled
      VT-d - disabled
      internal graphics - auto


      The problem is:
      I can log into the system normally without using my nvidia GPU but when I boot the system with the flags for webdrivers to work I fall into the login screen but it keeps flashing, I can see the mouse and I can move it but the screen flashes and the following error appears when the screen goes "black": IOConsoleUsers: gIOScreenLockState 3, hs 0, bs 0, now 0, sm 0x0. I searched for this error on the internet and tried to solve but to no avail so far.

      If someone can help me I would be extremely grateful! thanks in advance!

      Clover file attached.
      CLOVER.zip
    • By MaLd0n
      ---TUTORIAL---

      https://olarila.com/forum/viewtopic.php?f=50&t=8685
       
      --Original Post--
       
      https://olarila.com/forum/viewtopic.php?f=97&t=11237
       
      --Bios/UEFI Settings--
       
      *Update bios/uefi to F7+*
      1- Go to M.I.T./Advanced Frequency Settings tab
       
      Extreme Memory Profile (X.M.P.) - Profile 1
       
      2- Go to BIOS tab
       
      CSM Support - Disabled
       
      3- Go to Peripherals/Thunderbolt(TM) Configuration tab
       
      Security Level - No Security
      Thunderbolt USB Support - Enabled
      GPIO3 Force Pwr - Enabled
       
      4- Go to Chipset tab
       
      Internal Graphics - Enable
       
      ---CLOVER FOLDER---
      *Use this folder with FULL DSDT PATCHED
      EFI CLOVER Z390 DESIGNARE.zip
       
      ---OPENCORE FOLDER---
      *Use this folder with FULL DSDT PATCHED
      EFI OPENCORE Z390 DESIGNARE.zip
       
      ---DSDT patch requests is here---
       
      https://olarila.com/forum/viewtopic.php?f=19&t=1131
       
      ---HARDWARE---
       
      --MOBO

      GIGABYTE Z390 DESIGNARE
      -Link
      https://www.amazon.com/Z390-DESIGNARE-Gigabyte-Thunderbolt-Motherboard/dp/B07K8RJZRG/ref=sr_1_1?keywords=Z390+DESIGNARE&qid=1565492390&s=electronics&sr=1-1

      --PROCESSOR

      Intel Core i9-9900K
      -Link
      https://www.amazon.com/Intel-i9-9900K-Desktop-Processor-Unlocked/dp/B005404P9I/ref=sr_1_1_sspa?keywords=Intel+Core+i9-9900K&qid=1553358099&s=gateway&sr=8-1-spons&psc=1

      --COOLER

      CORSAIR H100i RGB PLATINUM AIO Liquid CPU Cooler
      -Link
      https://www.amazon.com/CORSAIR-H100i-PLATINUM-Liquid-Cooler/dp/B07JWB5BSN/ref=sr_1_4?keywords=WATER+COOLER+CPU&qid=1565492509&s=gateway&sr=8-4

      --MEMORY

      Corsair CMW32GX4M2C3200C16 Vengeance RGB PRO 32GB (2x16GB) DDR4 3200 (PC4-25600)
      -Link
      https://www.amazon.com/Corsair-CMW32GX4M2C3200C16-Vengeance-PC4-25600-Desktop/dp/B07GTG2T7L/ref=sr_1_15?keywords=memory+ddr4+32&qid=1553358238&s=gateway&sr=8-15

      --GPU

      MSI RX Vega 64 AIR Boost 8G OC
      -Link
      https://www.amazon.com/MSI-RX-64-AIR-8G/dp/B07DH7S1X1/ref=sr_1_2?keywords=vega+64+gigabyte&qid=1565492819&s=electronics&sr=1-2

      --SSD

      Samsung 970 EVO 1TB SSD (MZ-V7E1T0BW) NVMe M.2 V-NAND
      -Link
      https://www.amazon.com/Samsung-970-EVO-1TB-MZ-V7E1T0BW/dp/B07BN217QG/ref=sr_1_1?keywords=s+samsung+970+evo+1tb&qid=1565493002&s=electronics&sr=1-1

      --POWER SUPPLY

      EVGA Supernova 1000 P2 80+ Platinum, 1000W ECO Mode Fully Modular 
      -Link
      https://www.amazon.com/EVGA-Supernova-Platinum-Crossfire-220-P2-1000-XR/dp/B00EKJQM5E/ref=sr_1_3?keywords=power+supply+1000w&qid=1565493196&s=gateway&sr=8-3

      --WIRELESS

      TP-Link Archer T9E
      -Link
      https://www.amazon.com/TP-Link-Archer-T9E-Beamforming-Technology/dp/B00TQEX7AQ/ref=sr_1_1?keywords=TP-Link+Archer+T9E&qid=1553358397&s=gateway&sr=8-1

      --CASE

      Thermaltake Core P5 Tempered Glass Black Edition ATX Open Frame Panoramic Viewing
      -Link
      https://www.amazon.com/Thermaltake-Tempered-Panoramic-Certified-CA-1E7-00M1WN-03/dp/B01N4IGVSC/ref=sr_1_2?keywords=Thermaltake+Core+P5&qid=1565493567&s=gateway&sr=8-2

      --DSDT Patches--
      -FIX ACPI ERRORS -FIX OEM SSDTs to AVOID ERRORS AND WARNINGS -REMOVE UNUSED SCOPES / DEVICES -HIGH PRECISION EVENT TIMER -SATA -DMAC -REMOVE PROBLEMATIC AND UNUSED DEVICES -FIX K.P in REBOOT -SLPB -DARWIN / WINDOWS 2015 -XHCI -PLUGIN TYPE -HDAS to HDEF -HDEF -REAL TIME CLOCK -ARTC -IRQs -SBUS -BUS1 -MCHC -ALS0 -SHUTDOWN -LAN -FWHD -USBX -PMCR -PPMC -XSPI -CNVW -GMM -IMEI -EC -PNLF -ARPT -GFX0 -NVME -DTGP -ACQUIRE MUT0 0XFFFF -MUTEX MUT0 0x00 -EXTERNAL REFERENCES -UNKNOWNOBJ -HDMI / HDAU -FULL RENAMED DEVICES ---SCREENSHOTs---




















      -Credits and thanks to the old and new people in the community who developed patches, kexts and bootloaders!
      Thanks to KGP for SSDT Thunderbolt
      Slice, Kabyl, usr-sse2, jadran, Blackosx, dmazar, STLVNUB, pcj, apianti, JrCs, pene, FrodoKenny, skoczy, ycr.ru, Oscar09, xsmile, SoThOr, RehabMan, Download-Fritz, Zenit432, cecekpawon, Intel, Apple, Oracle, Chameleon Team, crazybirdy, Mieze, Mirone, Oldnapalm, netkas, Elconiglio, artut-pt, ErmaC, Pavo, Toleda, Master Chief and family, bcc9, The King, PMheart, Sherlocks, Micky1979, vit9696, vandroiy2013, Voodoo Team, Pike R. Alpha, lvs1974, Austere.J, CVad, Sampath007, onemanosx, erroruser, Jenny David, Olarila Facebook Community, Hackintosh Facebook Community and many others!
      We're all here to have fun and learn from each other!
    • By MaLd0n
      ---INSTALLATION TUTORIAL---
       
      ---Original Post---
      https://olarila.com/forum/viewtopic.php?f=45&t=9172
       
      ---USB---
      https://pikeralpha.wordpress.com/2016/07/13/simple-skylake-usb-fix-no-kexts-required/
       
      ---CLOVER FOLDER---
       
      CLOVER.zip
       
       
      --MOBO
      GigaByte Z390 M Gaming



      --PROCESSOR
      Intel Core i9-9900K


      --COOLER
      CoolerMaster MasterLiquid ML120R RGB


      --MEMORY
      Corsair Dominator Platinum 16GB (2 x 8GB)


      --GPU
      Sapphiretech Radeon RX 590 8 GB GDDR5


       
      --SSD
      Samsung 970 EVO NVMe M2 Flash Drive


      --POWER SUPPLY
      EVGA 750 N1, 750W


      --WIRELESS
      TP-Link Archer T9E


      --BLUETOOTH
      Orico BTA-403


      --CASE
      Thermaltake View 21 Tempered Glass Edition


      --DSDT Patches--
      -FIX ERRORS AND WARNINGS -FIX ACPI ERRORS -REMOVE UNUSED SCOPES / DEVICES -HIGH PRECISION EVENT TIMER -SATA SERIE 10 ID -DMAC -REMOVE 22K LINES, PROBLEMATIC and UNUSED -FIX K.P in REBOOT -NVRAM / REAL TIME CLOCK -SLPB -DARWIN / WINDOWS 2015 -XHCI -PLUGIN TYPE -HDAS to HDEF -HDEF -REAL TIME CLOCK -ARTC -IRQs -SBUS -MIKEY -BUS1 -MCHC -ALS0 -SHUTDOWN -UAR1 -LAN -FWHD -USBX -PMCR -PPMC -XSPI -GMM -IMEI -EC -PNLF -ARPT -GFX0 -NVME -DTGP -ACQUIRE MUT0 0XFFFF -OPERATION REGION GPIO -MUTEX MUT0 0x00 -EXTERNAL REFERENCES -UNKNOWNOBJ -HDMI / HDAU -FULL RENAMED DEVICES  
      --SCREENSHOTS--





























      --BruceX--
       
      --USB-C-- test with SanDisk Ultra USB-STICK 128gb


       
      -Credits and thanks to the old and new people in the community who developed patches, kexts and bootloaders!
      Slice, Kabyl, usr-sse2, jadran, Blackosx, dmazar, STLVNUB, pcj, apianti, JrCs, pene, FrodoKenny, skoczy, ycr.ru, Oscar09, xsmile, SoThOr, RehabMan, Download-Fritz, Zenit432, cecekpawon, Intel, Apple, Oracle, Chameleon Team, crazybirdy, Mieze, Mirone, Oldnapalm, netkas, Elconiglio, artut-pt, ErmaC, Pavo, Toleda, Master Chief and family, bcc9, The King, PMheart, Sherlocks, Micky1979, vit9696, vandroiy2013, Voodoo Team, Pike R. Alpha, lvs1974, Austere.J, CVad, Sampath007, onemanosx, erroruser, Jenny David, Olarila Facebook Community, Hackintosh Facebook Community and many others!
      We're all here to have fun and learn from each other!
×