Jump to content
glasgood

Glasgood's macOS Mojave [SUCCESS][GUIDE] for Aorus Z390 Pro

1,470 posts in this topic

Recommended Posts

2 hours ago, bleedingstar said:

Mm. I managed to install windows on a separate disk and I can now dual boot. However still when booting into osx I often get this panic, sometimes I have to reboot 4 times...

Now yesterday I spent quite some time in windows and this morning when I wanted to boot into osx I got a new problem, it doesn't even get to the panic anymore, it stops here:

Before when I got the panic I could circumvent it by booting with the usb installer plugged in, but now even that doesn't work and I'm stuck at this screen.. 

Any clue what's happening here? 

 

edit: When I boot into windows my radeon software shows a popup with: "Default radeon wattman settings have been restored due to an unknown error"

Everything else works fine in windows.

 

edit2: I changed DVMT pre-allocated from 256 to 96 and it now manages to go beyond the screen below, however I'm back in kernel panic terratory. I just don't understand why its so unstable..

 

system info:

 

my system info: 

Gigabyte Z390 AORUS PRO WIFI

I9-9900k

Corsair vengeance lox 32gb 3200mhz

Sapphire Radeon RX Vega 56 8gb

Samsung 970 EVO M.2 500gb (osx)

Samsung 840 250gb (windows)

 

 

 

 

Can you attach EFI so that I can look at your PCI properties. Please go back and change DVMT pre-allocated to 256 and disable XMP if enabled....  have same settings for BIOS as shown in guide. 

 

 

 

 

Share this post


Link to post
Share on other sites
Advertisement
11 hours ago, Sceme29 said:

Hello @glasgood , 

 

So I have been following this thread for little over a week now and I can say I’m more confident then ever to start my Hackintosh build that I’ve been planning for the past year. I will be receiving my final part in the mail tomorrow and will begin the process of setting up the Hackintosh. 

 

I bought a lot of the parts described in this thread with some minor differences.

- Motherboard - z390 aosus pro WiFi 

- intel i7, 8700k

- Corsair H115i pro

- G.skill tridents rgb 32gb

- sapphire pulse radeon rx580

- hp ex950 m.2 2280 1tb nvme

- Broadcom bcm94360csax with pci-e adapter

 

Im hoping this install goes smoothly especially since I’m using the Z390 WiFi version. Thank you for all the time and resources you have put into this thread, it is so well put together! I will keep you updated in the process. I will be starting it tomorrow!

 

 

Follow BIOS settings closely, keep XMP disabled and don't overclock CPU until macOS is installed and running smoothly. When macOS is installed and confirmed running stable then proceed with overclocks, enable XMP etc..  if needed. 

 

Best!

 

Share this post


Link to post
Share on other sites

@AudioGod

 

Looking through your Log, I noticed you have different defaults:

 

 679830119_Screenshot2019-06-24at09_18_24.thumb.png.e1cfe9fb9fd63b33fc9a2d8edb822939.png

 

180525478_Screenshot2019-06-24at09_21_30.thumb.png.b08e664e7820f3a10c3d71fe6e93e4b4.png

 

 

 

My Gui section in config.plist is minimal. SetMaxResolution: 2560x1440 is auto detected for my Dell U2715h monitor. 

 

242771557_Screenshot2019-06-24at09_33_05.thumb.png.019a75070afdff1a64300f7207839a15.png

 

 

Share this post


Link to post
Share on other sites
6 minutes ago, glasgood said:

@AudioGod

 

Looking through your Log, I noticed you have different defaults:

 

 679830119_Screenshot2019-06-24at09_18_24.thumb.png.e1cfe9fb9fd63b33fc9a2d8edb822939.png

 

180525478_Screenshot2019-06-24at09_21_30.thumb.png.b08e664e7820f3a10c3d71fe6e93e4b4.png

 

 

 

My Gui section in config.plist is minimal. SetMaxResolution: 2560x1440 is auto detected for my Dell U2715h monitor. 

 

242771557_Screenshot2019-06-24at09_33_05.thumb.png.019a75070afdff1a64300f7207839a15.png

 

 

 

Different defaults meaning what buddy?

 

I am using the tonumacx86 theme yes...lol

I like the black layout and cant stand clovers default skin.

I have not got to the bottom at all of the stuck resolution no :(

Share this post


Link to post
Share on other sites
Posted (edited)
9 minutes ago, AudioGod said:

 

Different defaults meaning what buddy?

 

I am using the tonumacx86 theme yes...lol

I like the black layout and cant stand clovers default skin.

I have not got to the bottom at all of the stuck resolution no :(

 

 

When comparing our log's, your getDefaultSettings look completely different to mine ( highlighted in red in screenshot ). Can you attach your EFI, mind remove serial numbers etc.. 

The Clover default ( white-ish ) colour can be changed to dark charcoal-ish colour by removing "random" from Gui.  

 

 

Edited by glasgood

Share this post


Link to post
Share on other sites
Posted (edited)
43 minutes ago, glasgood said:

 

 

When comparing our log's, your getDefaultSettings look completely different to mine ( highlighted in red in screenshot ). Can you attach your EFI, mind remove serial numbers etc.. 

The Clover default ( white-ish ) colour can be changed to dark charcoal-ish colour by removing "random" from Gui.  

 

 

 

Here you go buddy, I changed my theme over to a new one last night called neon so no more tonymacx86 theme here...lol

I got to the bottom of the random boot freeze at startup though, It was my SSD drive, In windows I had Samsung magician installed and it had turned on its ssd boost feature in windows and it was freaking out clover I think as the second I turned it back off it hasn't froze since so fingers crossed that's that sorted.

Also fingers crossed you find something a miss resolution wise.

If the EFI folder and my changes are good then your welcome to list it as an alternative EFI for people with a 9900k and Vega 56 :)

 

Thank you for taking the time out to look at my problem bro, Your a top draw good guy. Awesome Buddy

 

AudioGod EFI.zip

Edited by AudioGod

Share this post


Link to post
Share on other sites
16 minutes ago, AudioGod said:

 

Here you go buddy, I changed my theme over to a new one last night called neon so no more tonymacx86 theme here...lol

I got to the bottom of the random boot freeze at startup though, It was my SSD drive, In windows I had Samsung magician installed and it had turned on its ssd boost feature in windows and it was freaking out clover I think as the second I turned it back off it hasn't froze since so fingers crossed that's that sorted.

Also fingers crossed you find something a miss resolution wise.

If the EFI folder and my changes are good then your welcome to list it as an alternative EFI for people with a 9900k and Vega 56 :)

 

AudioGod EFI.zip

 

Thanks, EFI looks fine. Resolution wise, I can't think why. What is the screen resolution of your monitor ?

Share this post


Link to post
Share on other sites
Posted (edited)
30 minutes ago, glasgood said:

 

Thanks, EFI looks fine. Resolution wise, I can't think why. What is the screen resolution of your monitor ?

 

Its 2160p (4k)

I used the neon theme instead now as it looks great even at my stuck resolution.

I'm thinking it's just the way it is with my vega 56 as researching it online last night I found a good few other people with the same problem using a vega card.

 

Am I correct in thinking I should deselect dark in enbedded theme mode under gui in clover and make it blank as I'm using my own theme? 

 

I'm going to reinstall mojave later on to my spare ssd to play with your alternative way of installing macos so I will stick my efi inside it and see if it does the same thing resolution wise as a test to see if its something to do with me changing over my GPU.

TBH I doubt it's that but il try anyway otherwise I give up! LoL

 

If I was too put my efi onto my usb mojave install key as a resolution test would that work too? Just as a test.

Edited by AudioGod

Share this post


Link to post
Share on other sites
9 minutes ago, AudioGod said:

Its 2160p (4k)

I used the neon theme instead now as it looks great even at my stuck resolution.

I'm thinking it's just the way it is with my vega 56 as researching it online last night I found a good few other people with the same problem using a vega card.

 

Am I correct in thinking I should deselect dark in enbedded theme mode under gui in clover and make it blank as I'm using my own theme? 

 

@AudioGod

 

Possibly down to something in Vega 56 cards firmware ( is a firmware update available )  . Can you try the following, if 3840x2160 does not work then try 2560x1440 : 

 

1158297100_Screenshot2019-06-24at11_20_56.thumb.png.3a03736bd23671a698ede6e260ed049d.png

 

Reboot and test.

 

If still same then enable Patch VBIOS.

 

1904251423_Screenshot2019-06-24at11_20_07.thumb.png.f43d596457278212c114c6d8c0936ea7.png

 

 

 

 

 

Share this post


Link to post
Share on other sites
Posted (edited)

@AudioGod

 

You could also try Windows 8/10 WHQL, though it might cause problem with unsigned windows drivers used in Windows ( if any ) . Test with patch VBios off .

Edited by glasgood

Share this post


Link to post
Share on other sites
2 minutes ago, glasgood said:

@AudioGod

 

You could also try Windows 8/10 WHQL, though it might cause problem with unsigned windows drivers used in Windows ( if any ) . Test with patch VBios off .

I tried changing to win 8/10 and WHQL last night to no effect.

I will check for a bios update for the card now and failing that il give VBios a try.

Share this post


Link to post
Share on other sites
Posted (edited)
2 hours ago, glasgood said:

 

@AudioGod

 

Possibly down to something in Vega 56 cards firmware ( is a firmware update available )  . Can you try the following, if 3840x2160 does not work then try 2560x1440 : 

 

1158297100_Screenshot2019-06-24at11_20_56.thumb.png.3a03736bd23671a698ede6e260ed049d.png

 

Reboot and test.

 

If still same then enable Patch VBIOS.

 

1904251423_Screenshot2019-06-24at11_20_07.thumb.png.f43d596457278212c114c6d8c0936ea7.png

 

 

 

 

 

 

I tried all of the above to no effect.

Theres no bios update for the card that I can find either.

Hmmmmmmmm

 

Also I noticed that as you.know I have erp enabled on my system as standard and when my system is sleeping in this mode it will wake it self up for email or notifications then go back to sleep and downloads will also continue all as it should do but yesterday I switched erp off and didn't turn it back on just seeing if it was causing the res issue (yes I was clutching at straws...haha) but what I did notice while it was off is that sleep and wake behaviour that I just mentioned doesn't work in the same manner if at all.

Check that one out for yourself and your see what I mean :)

Edited by AudioGod

Share this post


Link to post
Share on other sites
6 hours ago, glasgood said:

 

 

Can you attach EFI so that I can look at your PCI properties. Please go back and change DVMT pre-allocated to 256 and disable XMP if enabled....  have same settings for BIOS as shown in guide. 

 

 

 

 

The EFI is attached, I'll revert the bios settings back to a bios screen dump you sent me earlier. 
Like before, using the pre-install EFI on my rescue usb gives me no problems during boot. 

 

 

Archive.zip

Share this post


Link to post
Share on other sites
5 hours ago, glasgood said:

@AudioGod

 

Another thing to explore . would be to test the change from other OS to Windows 8/10. 

 

618895499_Screenshot2019-06-24at11_41_55.thumb.png.bc316d8f94681e9d1ffca6f2018496b7.png

 

 

 

 

 

190624103518.BMP

 

@glasgood

 

Update, I have got to the bottom of it finally.

I found a new bios for my Pulse Vega56 and in the notes it mentioned it resolved random boot panics that was something I was seeing but thought I fixed it by updating my ssd bios as it hasn't happened since but anyway I updated my bios on the vega 56 and then rebooted and had to go into my motherboard bios after that and turn off CSM Support (that I prefer off anyway if not needed) and BAM the clover boot screen popped up in glorious 2160p. 

What a process to get it too work though but it was defo the bios on the vega 56 that needed the update.

Everything is looking spot on now and I've run out of things to do to my setup at long last...lol

 

@larabee

 

Could this be why your also getting random boot panics too?

 

I can attach a copy of the bios update and updating tool for you if you want buddy?

It's easy too flash. 

 

Just let me know and il upload it for you straight away. :)

Share this post


Link to post
Share on other sites
Posted (edited)
1 hour ago, bleedingstar said:

 

The EFI is attached, I'll revert the bios settings back to a bios screen dump you sent me earlier. 
Like before, using the pre-install EFI on my rescue usb gives me no problems during boot. 

 

 

Archive.zip

 

Check BIOS settings are same as guide and replace your old EFI with ==>EFI inside Archive.zip then shutdown and restart, if you get a kernel panic then shutdown and restart. You will need to import your PCI info from hackintool 

 

After importing PCI info, ensure you have following CPU properties.

 

27308553_Screenshot2019-06-24at16_55_31.png.628b32462b288a87e0b867cf1d43bd87.png

 

 

 

 


 

Edited by glasgood

Share this post


Link to post
Share on other sites

@AudioGod

 

 

Thats fantastic news, glad you got that sorted. Can you provide link to firmware update and some details for others with your card, I will link from guide to your post. 

Share this post


Link to post
Share on other sites
2 hours ago, glasgood said:

@AudioGod

 

 

Thats fantastic news, glad you got that sorted. Can you provide link to firmware update and some details for others with your card, I will link from guide to your post. 

 

Sure thing buddy will do as soon as I get back home.

I've already compiled a zip file for you with the bios and the tool I used and a copy of CPUz to make sure it all lines up.

Il send it over asap and a small guide :)

Share this post


Link to post
Share on other sites
8 hours ago, AudioGod said:

 

@glasgood

 

Update, I have got to the bottom of it finally.

I found a new bios for my Pulse Vega56 and in the notes it mentioned it resolved random boot panics that was something I was seeing but thought I fixed it by updating my ssd bios as it hasn't happened since but anyway I updated my bios on the vega 56 and then rebooted and had to go into my motherboard bios after that and turn off CSM Support (that I prefer off anyway if not needed) and BAM the clover boot screen popped up in glorious 2160p. 

What a process to get it too work though but it was defo the bios on the vega 56 that needed the update.

Everything is looking spot on now and I've run out of things to do to my setup at long last...lol

 

@larabee

 

Could this be why your also getting random boot panics too?

 

I can attach a copy of the bios update and updating tool for you if you want buddy?

It's easy too flash. 

 

Just let me know and il upload it for you straight away. :)

 

Oh dear, I would love to have that bios. Thank you so much. I've had random boot panics with ATI Frame buffer. Will that affect its performance in windows? 

Share this post


Link to post
Share on other sites
Posted (edited)
14 hours ago, larabee said:

 

Oh dear, I would love to have that bios. Thank you so much. I've had random boot panics with ATI Frame buffer. Will that affect its performance in windows? 

 

Performance has gone up in windows with the new bios. I just scored 7562 in timespy using a voltage of 1075 on p7 and 1025 on p6 1582, 1637 frequencies and 920 on the memory. 

That's nearly 100 points higher then before I flashed it.

Try those settings on your vega56, it's a nice balance I think. :)

 

I have posted the bios and flash tool plus a mini guide if needed.

Let me know your results when you do it. :)

 

 

Edited by AudioGod

Share this post


Link to post
Share on other sites
Posted (edited)
22 hours ago, glasgood said:

@AudioGod

 

 

Thats fantastic news, glad you got that sorted. Can you provide link to firmware update and some details for others with your card, I will link from guide to your post. 

 

If you own a Sapphire Pulse Vega 56 and your having problems with the clover bootscreen resolution or getting boot kernal panics at start up then the chances are that your graphics card is using an old bios that conflicts with macOS so all you need to do is flash your GPU bios using the new bios, flash tool and GPUZ that I have provided.

 

If you don't know or are unsure on how to flash your GPU bios then here's simple guide to walk you though it and you are going to need to use the windows 10 side of life for the bios flash.

 

https://www.techpowerup.com/forums/threads/amd-ati-flashing-guide.212849/


 

After you have done that go into your motherboards bios and Disable CSM Support, restart the system and your clover boot screen should automatically go to your monitors default resolution and the random boot kernal panics should be gone.

If your resolution is still stuck at the wrong size after that then all you need to do is set the resolution within your clover config.plist using Clover Configurator in the GUI section.


 

Sapphire Vega 56 Pulse New Bios and flash tool.zip

Edited by AudioGod

Share this post


Link to post
Share on other sites

@glasgood

Ive posted the bios and tools as you requested buddy and given a little explanation that I hope makes sense...lol

 

@larabee

I hope it sorts your problems out for you too. let me know how you get on :)

Share this post


Link to post
Share on other sites

sometimes my usb keyboard and magic trackpad 2 suddenly stop working, do u known how to fix it ?

Share this post


Link to post
Share on other sites
Posted (edited)

@AudioGod

 

Thanks, I put a note and your link at the "Before you start" section in the guide. 

 

Cheers!

Edited by glasgood

Share this post


Link to post
Share on other sites
Guest
This topic is now closed to further replies.

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By benmills1
      Hi, i can someone help me with installing mac OS Mojave on my HP ENVY - 15-as102na?
      I have an imac to use for setting up my usb & installing MacOS Mojave.There are various kext files etc that i'm not sure about and need some help as some are hardware specific.
      I tried previously but got stuck on an apple logo and couldn't get past that, and tried today and had problems with Clover.
      Once i get mac os on my 128gb m.2 ssd ( which i'll upgrade to either a 256gb or 512gb depending on how well this hackintosh works)
      I have a free 2.5" inch hdd bay where i'd like to install windows on in the future.
      I think i may have to replace my wireless card ( based on a few google results) which i'm fine with as long as i can see it working without just so i know i won't waste money
      Specs:
      Cpu: i5 7200u
      GPU: HD 620
      8GB ram
      Wifi card- Intel Wireless 7265 ( Intel® 802.11ac (2x2) )
      Motherboard - HP 81D2 & BIOS version is f.56
      https://support.hp.com/gb-en/document/c05311862
      Thanks
    • By MaLd0n
      ---TUTORIAL---

      https://olarila.com/forum/viewtopic.php?f=50&t=8685
       
      --Original Post--
       
      https://olarila.com/forum/viewtopic.php?f=97&t=11237
       
      --Bios/UEFI Settings--
       
      *Update bios/uefi to F7+*
      1- Go to M.I.T./Advanced Frequency Settings tab
       
      Extreme Memory Profile (X.M.P.) - Profile 1
       
      2- Go to BIOS tab
       
      CSM Support - Disabled
       
      3- Go to Peripherals/Thunderbolt(TM) Configuration tab
       
      Security Level - No Security
      Thunderbolt USB Support - Enabled
      GPIO3 Force Pwr - Enabled
       
      4- Go to Chipset tab
       
      Internal Graphics - Enable
       
      ---CLOVER FOLDER---
      https://olarila.com/forum/download/file.php?id=25033
      *Use this folder with FULL DSDT PATCHED
       
      ---OPENCORE FOLDER---
      https://olarila.com/forum/download/file.php?id=24376
      *Use this folder with FULL DSDT PATCHED
       
       
      ---Extract one Full dump for DSDT edits, post files---
       
      RunMe.app
       
       
       
      ---HARDWARE---
       
      --MOBO

      GIGABYTE Z390 DESIGNARE
      -Link
      https://www.amazon.com/Z390-DESIGNARE-Gigabyte-Thunderbolt-Motherboard/dp/B07K8RJZRG/ref=sr_1_1?keywords=Z390+DESIGNARE&qid=1565492390&s=electronics&sr=1-1

      --PROCESSOR

      Intel Core i9-9900K
      -Link
      https://www.amazon.com/Intel-i9-9900K-Desktop-Processor-Unlocked/dp/B005404P9I/ref=sr_1_1_sspa?keywords=Intel+Core+i9-9900K&qid=1553358099&s=gateway&sr=8-1-spons&psc=1

      --COOLER

      CORSAIR H100i RGB PLATINUM AIO Liquid CPU Cooler
      -Link
      https://www.amazon.com/CORSAIR-H100i-PLATINUM-Liquid-Cooler/dp/B07JWB5BSN/ref=sr_1_4?keywords=WATER+COOLER+CPU&qid=1565492509&s=gateway&sr=8-4

      --MEMORY

      Corsair CMW32GX4M2C3200C16 Vengeance RGB PRO 32GB (2x16GB) DDR4 3200 (PC4-25600)
      -Link
      https://www.amazon.com/Corsair-CMW32GX4M2C3200C16-Vengeance-PC4-25600-Desktop/dp/B07GTG2T7L/ref=sr_1_15?keywords=memory+ddr4+32&qid=1553358238&s=gateway&sr=8-15

      --GPU

      MSI RX Vega 64 AIR Boost 8G OC
      -Link
      https://www.amazon.com/MSI-RX-64-AIR-8G/dp/B07DH7S1X1/ref=sr_1_2?keywords=vega+64+gigabyte&qid=1565492819&s=electronics&sr=1-2

      --SSD

      Samsung 970 EVO 1TB SSD (MZ-V7E1T0BW) NVMe M.2 V-NAND
      -Link
      https://www.amazon.com/Samsung-970-EVO-1TB-MZ-V7E1T0BW/dp/B07BN217QG/ref=sr_1_1?keywords=s+samsung+970+evo+1tb&qid=1565493002&s=electronics&sr=1-1

      --POWER SUPPLY

      EVGA Supernova 1000 P2 80+ Platinum, 1000W ECO Mode Fully Modular 
      -Link
      https://www.amazon.com/EVGA-Supernova-Platinum-Crossfire-220-P2-1000-XR/dp/B00EKJQM5E/ref=sr_1_3?keywords=power+supply+1000w&qid=1565493196&s=gateway&sr=8-3

      --WIRELESS

      TP-Link Archer T9E
      -Link
      https://www.amazon.com/TP-Link-Archer-T9E-Beamforming-Technology/dp/B00TQEX7AQ/ref=sr_1_1?keywords=TP-Link+Archer+T9E&qid=1553358397&s=gateway&sr=8-1

      --CASE

      Thermaltake Core P5 Tempered Glass Black Edition ATX Open Frame Panoramic Viewing
      -Link
      https://www.amazon.com/Thermaltake-Tempered-Panoramic-Certified-CA-1E7-00M1WN-03/dp/B01N4IGVSC/ref=sr_1_2?keywords=Thermaltake+Core+P5&qid=1565493567&s=gateway&sr=8-2

      --DSDT Patches--
      -FIX ACPI ERRORS -FIX OEM SSDTs to AVOID ERRORS AND WARNINGS -REMOVE UNUSED SCOPES / DEVICES -HIGH PRECISION EVENT TIMER -SATA -DMAC -REMOVE PROBLEMATIC AND UNUSED DEVICES -FIX K.P in REBOOT -SLPB -DARWIN / WINDOWS 2015 -XHCI -PLUGIN TYPE -HDAS to HDEF -HDEF -REAL TIME CLOCK -ARTC -IRQs -SBUS -BUS1 -MCHC -ALS0 -SHUTDOWN -LAN -FWHD -USBX -PMCR -PPMC -XSPI -CNVW -GMM -IMEI -EC -PNLF -ARPT -GFX0 -NVME -DTGP -ACQUIRE MUT0 0XFFFF -MUTEX MUT0 0x00 -EXTERNAL REFERENCES -UNKNOWNOBJ -HDMI / HDAU -FULL RENAMED DEVICES ---SCREENSHOTs---




















      -Credits and thanks to the old and new people in the community who developed patches, kexts and bootloaders!
      Thanks to KGP for SSDT Thunderbolt
      Slice, Kabyl, usr-sse2, jadran, Blackosx, dmazar, STLVNUB, pcj, apianti, JrCs, pene, FrodoKenny, skoczy, ycr.ru, Oscar09, xsmile, SoThOr, RehabMan, Download-Fritz, Zenit432, cecekpawon, Intel, Apple, Oracle, Chameleon Team, crazybirdy, Mieze, Mirone, Oldnapalm, netkas, Elconiglio, artut-pt, ErmaC, Pavo, Toleda, Master Chief and family, bcc9, The King, PMheart, Sherlocks, Micky1979, vit9696, vandroiy2013, Voodoo Team, Pike R. Alpha, lvs1974, Austere.J, CVad, Sampath007, onemanosx, erroruser, Jenny David, Olarila Facebook Community, Hackintosh Facebook Community and many others!
      We're all here to have fun and learn from each other!
    • By AudioGod
      I have put together this simple little guide for anybody wanting to use a Patched DSDT EFI with the same configuration as me.
      This is also a thread to discuss everything Z390 Pro and try and help where we can and maybe make things a little better for you. 
       
      A huge massive thank you to @glasgood @MaLd0n @larabee These three guys have helped me and talked me so much and are as helpful as you could ever get, Without them I wouldn't have a perfect working build like I do or be putting up this Guide & Discussion Thread sharing the hard work and countless hours that we have all put in to this.   
       
       
      This EFI and Patched DSDT have been created to work with a Gigabyte Aorus Z390 Pro, 9900k with a Vega 56 but has also been tested and verified fully working with the following Hardware
       
      CPU's
      8700k, 9600k, 9700k, 9900k
       
      GPU's
      RX 560, 570, 580, 590, Vega 56, Vega 64, Radion VII
      (If you have success with any different CPU or GPU's then please do let me know)
       
       
      There Is No Better Guide Then The One That @glasgood Has Already Written So Just Follow He's Guide For a Perfect Install.     
       
       
      HARDWARE USED
      • Intel I9 9900k 
      • Gigabyte AORUS Z390 PRO
      • Sapphire Nitro+ SE Vega56 ( connected to monitor with DisplayPort )
      • Corsair Vengeance Pro RGB 16GB @3200mhz (2 x 8GB)
      • Corsair RM850x 80 Plus Gold Power Supply Unit
      • Coolermaster MASTERLIQUID ML360R RGB CPU Cooler
      • Samsung 970 EVO 1TB NVMe SSD macOS Mojave
      • Samsung 860 EVO 1TB SSD (2.5) Windows 10 Pro
      • ABWB BCM943602CS 802.11AC WI-FI With Bluetooth 4.0 PCI-Express (PCI-E)   
      • Lian Li PC-O11DW Dynamic ATX Case
       

       

       
       
      WORKING
      • Sound 
      • Ethernet Port
      • WiFi
      • SSD Trim
      • USB 3.0 & 2.0 (All ports Open Natively)
      • AirDrop
      • iCloud
      • Hardware Acceleration
      • iMessages
      • Facetime
      • Sleep & Wake
      • Sleep and Shutdown via the Power Button
      • Handoff
      • Netflix on Safari browser
      • Continuity
       
       
      CLOVER  FOLDER
      Use this folder with fully patched DSDT
      Z390 Pro DSDT EFI.zip   (Updated 21 July 2019)
       
       
      ADDITIONAL DSDT's  (A big thanks to @MaLd0n for compiling these extra DSDT's)
      If your using a Vega 56/64 or Radion VII then use this DSDT (already installed in my EFI)
      DSDT.VEGA.VII.zip
      If your using a RX Series or Nvidia GPU then use this DSDT
      DSDT.RXxxx.NVIDIA.zip
       
       
      To Create Your Own Patched DSDT Message @MaLd0n using the link bellow
      https://olarila.com/forum/viewtopic.php?f=19&t=1131 
      (If you want a perfect setup then getting your own patched DSDT made would be the best thing to do, Mine will work perfectly fine but different hardware no matter how small a change it is can tend to have some sort of effect on the DSDT and your setup)
       
       
      If Your Not Using File Vault Then Please Disable Hibernate
      disablehibernate.command
       
       
      ADDITONAL DOWNLOADS
      Clover
      Clover Configurator
      Kext Updater
       
       
      OPTIONAL DOWNLOADS
      AirportBrcmFixup.kext    (If your Wifi Card isn't working after installing my EFI then add the AirportBrcmFixup.kext to your clover kext folder and reboot)
      FakeSMC    (Can be used instead of VirtualSMC)
      Hackintool
      IORegistryExplorer
      Native Display Brightness with MonitorControl
       
       
      BIOS SETTINGS (Bios Revision F10)
       
      • Enter BIOS → Press F12 → Enter Setup
      • Save & Exit → Load Optimized Defaults
       
      • BIOS → Windows 8/10 Features → Other OS
      • BIOS → CSM Support → Enabled  (Can be set to disabled depending on what GPU you use)
       
      • MIT → Advanced Memory Settings  → Extreme Memory Profile (X.M.P) → Enabled  
       
      • Peripherals → Initial Display Output → PCIe 1 Slot
      • Peripherals → Trusted Computing → Security Device Support →  Disable
      • Peripherals → Intel(R)Bios Guard → Intel BIOS Guard Support →  Disable
      • Peripherals → USB Configuration → Legacy USB Support →  Enabled
      • Peripherals → USB Configuration → XHCI Hand-off →  Enabled
      • Peripherals → Network Stack Configuration → Network Stack →  Disabled
      • Peripherals → SATA And RST Configuration → SATA Mode Selection →  AHCI
       
      • Chipset → Vt-d → Enabled  (can be enabled or disabled, your choice)
      • Chipset → Internal Graphics → Disabled
      • Chipset → Audio Controller → Enabled
      • Chipset → Above 4G Decoding → Disabled 
       
      • Power → Platform Power Management → Enabled
      • Power → ErP → Enabled  (can be enabled or disabled, your choice)
      • Power → RC6 (Render Standby) → Disabled
       
      • Save & Exit → Save & Exit Setup
       
       
      SCREENSHOTS
       

       

       

       

       

       

       

       

       

       

       

       

×