Jump to content
  1. valueimagery

    valueimagery

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By glasgood
      CLOVER DUAL BOOT MOJAVE & WINDOWS 10 GUIDE 
       

       
       
      INCLUDES  MBR / LEGACY BIOS  TO  GPT / EFI CONVERSION
      USING MBR2GPT TOOL
       
       
      PREREQUISITE: Two physical discs ( SSD’s or HDD’s )
       
       
       
       
       
      STEP 1 - Clover dual boot configuration 
       
      Open config.plist with Clover Configurator
       
      Boot
       Legacy = PBR Timeout = True ( will remove the Timeout countdown, from Clover boot menu)  

       
      GUI 
      Scan / Custom
       Entries = True  Tool = True  Legacy = False ( removes extra Windows 10 entries )  
      Hide Volume
      - Preboot ( macOS Preboot )
      - Recovery ( macOS Recovery )
       

       
      So at boot you will have two options: boot macOS Mojave or Windows 10 
       
       
       
       
       
       
       
      ————————————————————
       
       
      STEP 2 - Using a drive without Windows 10 installed
       
      Disconnect system drive that contains your macOS Mojave install from computer ( This is so that Windows does not overwrite existing macOS Mojave boot loader )
       
      Proceed with a Windows 10 UEFI install.  
      After installation reconnect macOS Mojave Drive, the Windows installation should now be detected and usable in Clover. 
      If Windows 10 is not detected or able to boot,  then verify you installed Windows 10 as UEFI and not MBR ---->  ( Read step 2 - For a drive with Windows 10 installed )
       
       
      OR
       
       
       
      STEP 2 - Using a drive with Windows 10 already installed
       
      Verify your Windows install is  GPT / UEFI or MBR / Legacy BIOS.   
      If Windows install is GPT UEFI then Windows 10 install is ready to use at Clover boot menu, you should be able to boot into Windows directly from Clover boot screen. 
       

       
       
      But if  Windows drive is detected at Clover boot screen, but when booting Windows you get a black screen with a cursor on the top left,
      then this is most likely because Windows drive is MBR ( Legacy BIOS ).  You can easily convert MBR to GPT using  Windows MBR2GPT tool ( this saves hours work having to reinstall Windows 10 and setting up all your applications again  ) 
       
      If Windows 10 install is MBR / Legacy BIOS  then simply convert to GPT / UEFI  following instructions below ( read video summary and view video )
       
       
      ** To use Windows 10  MBR2GPT tool  you must have Windows 10 version 1703 ( creators update  ) or later and less than 3 partitions on 
      the Windows 10 drive **
       
      Video summary:
       
      Confirm Windows 10 drive is MBR Legacy BIOS ( in Windows Disk Management ) Reboot into Windows PE ( Advanced Startup ) Convert from MBR Legacy BIOS to GPT UEFI ( using commands below ) mbr2gpt /validate mbr2gpt /convert Restart Verify Windows 10 drive has changed to GPT UEFI ( in Windows Disk Management )  
       
       
       
      After conversion Windows 10 is ready to use at the Clover boot menu 
       
       
    • By SepehrM
      I'm trying to install High Sierra 10.13.3 on an ASUS N552VW laptop, and I get stuck after this message:
      "could not recover SATA HDD after 5 attempts, terminating" 
      And some other warnings afterwards.
      Specs:
      CPU: Intel Skylake 6700HQ 2.6GHz
      RAM: 16GB DDR4
      2TB HDD + 128GB SSD
      GPU: Intel HD Graphics 530 + Nvidia GTX960m
      I'm installing using a 16GB USB3 flash drive on one of HDD volumes (UEFI Mode)
       
      I uploaded the verbose log and clover config.plist
      config-new.plist

    • By gk12345
      hello to everyone, i managed to install mojave on my asus ux303ub with i5 cpu and now sleep does not work when i press sleep display turns black and pc stays on and then i have to force shut down by holding power button in order to restart pc ,by the way i used the clover folder from a guide on the internet, any help would be appreciated, thanks
    • By Bahaa
      Need help here
      My graphic card is detached 7mb
      and I try a lot of solution and no one work 
      can any one help
       

    • By Gracie
      Hello, insanely kind people! 
      I had full working Speedstep on my system with El Capitan, but after installing Mojave i cant make it working again!
      Help me please. Actually system is working only with NullCPUPowerManagement.kext. As soon as i remove it from Extensions directory i've got kernel panic at the boot.
      I tried to put SSDT.aml from my previous ElCapitan clover, tried to make new by different utilities, but still no luck.

      My system is:
      Pentium G3258
      Asus Z97-K USB 3.1
      Nvidia GTX 670


      i''m attaching my new clover.plist of Mojave and old El Capitan one, which makes Speedstep fully working and overclocking my little Pentium from 3.2 to 4.5GHz. Now i see huge speed loss without SpeedStep on Mojave  Please help, anybody! Also im attaching my working SSDT.aml from El Capitan.
      El Capitan SSDT.aml
      El Capitan config.plist
      Mojave config.plist
×