Jump to content
forum

Mojave 14.2 on ga-x79-up4 - Sleep

17 posts in this topic

Recommended Posts

Hi guys,

after using yosemite for a long time with a complete working system, i decided to jump into a fresh install on my old system.

Most things work flawless, except USB3 and sleep which is the more important thing.

Every time i set it to sleep, it shuts down for a moment and then the system starts again with black screen and low power consumption +- 100w (normal idle is around 120-140).

I can only hard reset the system to get it working again.

I used the DSDT Patch from my old system, but i think it may have some errors.

I hape you do have an Idea what to do.

 

Here are my specs:

 

Gigabyte X79-up4

i7-3930k

32gb Ram

NVIDIA GeForce GTX 660 Ti 3071 MB

512 Samsung SSD

Mojave 14.2

newest bios

 

I attached the RunMe files.

 

Best

forum

Send me mojaves-iMac.fritz.box 2.zip

Edited by forum

Share this post


Link to post
Share on other sites
Advertisement

I updated the clover folder with your files and the system rebooted instantly after around 10 seconds after login to post again.
I could´nt even try to set the system to sleep..

I'm online again with my old efi.

 

:/

____

just for the record, that's the smaller Problem.

USB-Stick @ Usb2  Port was working in osx

USB-Stick @ USB3  Port was not working in osx

____

Share this post


Link to post
Share on other sites
24 minutes ago, forum said:

USB-Stick @ USB3  Port was not working in osx

 

Yes, I can see the USB 2.0 ports working in ioreg. However, I am not able to see any hint of USB 3.0 devices. You can try inject a XHC device in the dsdt.

 

EDIT: I opened up your working DSDT and found hundreds of errors. Managed to eliminate the errors only. See if it boots now with the attached DSDT.

 

 

DSDT.aml.zip

Screenshot 2018-12-15 at 12.18.16 PM.png

Edited by onemanOSX

Share this post


Link to post
Share on other sites

Thanks, the system seems to run a bit smoother than before, but i still can't get the system to sleep.

 

Every time i set it to sleep, the fans stop for a moment and the screen goes black.

After 2-3 seconds the fans start to spin again but the screen stays black und the system does not respond.

Rest button is not working so i have to manualy shut it down.

 

Any idea?

 

I attached the new runme files..

 

Best

forum

Send me mojaves-iMac.fritz.box.zip

Edited by forum

Share this post


Link to post
Share on other sites

Thanks a lot for your help, but sleep is still not working. Same Problem as before..

It drives me crazy, trying to fix it now for days. :surprised::moil:

 

 

9 hours ago, forum said:

 

Every time i set it to sleep, the fans stop for a moment and the screen goes black.

After 2-3 seconds the fans start to spin again but the screen stays black und the system does not respond.

Rest button is not working so i have to manualy shut it down.

 

Thats my new summary:

 

I Added the line from your config.plist
<key>NoDynamicExtract</key>
<true/>

Not sure what the dynamic DSDT extraction should do..

 

DSDT relpaced

USBInjectAll.kext was added
NullCPUPowerManagement.kext is needed for a working speedstep, testet with Intel Power Gadget and a power measure adapter. Sleep is not working with or without it.

NoVPAJpeg.kext was not added, because preview is working without problems. I do not think it will help with my sleep problem.

 

Share this post


Link to post
Share on other sites

hi, all X79 can't wake from sleep since 10,12,6 or high Sierra.

My asrock X79 does the same, even if for myself it didn't wake up spontaneously as you, which is another problem that can be solved.

For all of us, out of sleep it seems that the GPU can't initialized. DSDT has done nothing to it, or finding a specific patch. It seems related to the cpu not having IGPU.

 

keep the faith or stay in Yosemite. For using high Sierra for half a year , I didn't find any enormous improvements, more over, FCPX is {censored} not usable anymore, too slow !!! 

 

A+

 

Edited by abds69
correction

Share this post


Link to post
Share on other sites
10 hours ago, abds69 said:

all X79 can't wake from sleep since 10,12,6 or high Sierra.

 

15 hours ago, MaLd0n said:

Sleep workin' in x79 is rare:lol:

 

Thank you all for the clarification. 

Share this post


Link to post
Share on other sites

Hi, Mine sleep and wake works without problem in Sierra and HS. Got the same board with you as well X79-UP4, Xeon E5 2650v2, Quadro M4000.

Edited by triplekill111

Share this post


Link to post
Share on other sites
On 12/16/2018 at 4:22 AM, forum said:

Thanks a lot for your help, but sleep is still not working. Same Problem as before..

It drives me crazy, trying to fix it now for days. :surprised::moil:

 

 

 

Thats my new summary:

 

I Added the line from your config.plist
<key>NoDynamicExtract</key>
<true/>

Not sure what the dynamic DSDT extraction should do..

 

DSDT relpaced

USBInjectAll.kext was added
NullCPUPowerManagement.kext is needed for a working speedstep, testet with Intel Power Gadget and a power measure adapter. Sleep is not working with or without it.

NoVPAJpeg.kext was not added, because preview is working without problems. I do not think it will help with my sleep problem.

 

Hello dude, i am trying to make an hackintosh with the X79 UP4 3930k and 1080ti but i get some problem to get the port 3.0 working : they are simply not detected in 2.0 or 3.0.

Is there a way that you share me your final EFI ? I am under 10.13.6.

 

Thank you.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By cixque
      CLOVER.zipCLOVER.zipDell Venue 11 Pro 7140
      ------------
      Specification
       
       
      Intel Core M 5Y71
       
      Intel HD Graphics 5300
       
      Intel Broadwell-U motherboard
       
      8GB Ram
       
      256GB SSD
       
      Dell DW1850e WWAN + GNSS GPS
       
      Intel Wireless 7265 + Intel Bluetooth
       
      NFC
       
       
      …..
       
       
       
       
       
      Mojave 10.14.6
       
      What works
      Native Power Manager (Generate Plugin type) Full Graphics with QE/CL Brightness (Add PNLF in Config.plist or DSDT Patch) — (Brightness slide bar) Touch Screen, and Pen (DSDT Patch + Voodoo I2C, I2CHID satellite KEXT) HDMI output with hot plug (Lilu + WhateverGreen) HDMI Audio with hot plug (Lilu + AppleALC) no Layout-id needed Front and Rear Cameras MicroSD slot - O2 Micro (I use Adding Arbitrary under Devices in Config file Method) Ref, Post #6 by Jake Jo https://osxlatitude.com/forums/topic/7346-applesdxc-driverdsdt-patch-for-o2-micro-sd-card-readers/ Battery Indicator (ACPIbattery by Rehabman) ——>To utilise both battery, SSDT (by Rehabman) is needed in order to combine 2 batteries as one.
      Travel Keyboard Dell K12a001 (USBinjectall KEXT) Native Keyboard keys (Brightness, volume keys) WWAN card Dell DW1850e (OOB) Bluetooth -------------------
       
      What doesn’t work
       
       
      Sleep Wake — I have no idea how to fix it as it is required DSDT patch I guess. GPS NFC Audio ---> Realtek I2S Audio (PG0.35 for DELL)
       
      In DSDT entries is HDAUDIO\\FUNC_01&VEN_10EC&DEV_0282&SUBSYS_00000000&REV_1000\ Which indicates ALC282
       
      Audio ALC3263 (As it shown in BIOS) - Broadwell rt286 - Card1/Codec#0 (Utilised in I2S Mode) there is nowhere in BIOS to change to HDA mode). Drop OEM HDA and Fix HDA don’t do anything, still show 3 HDMI Audio outputs. If there is a DSDT patch to force HDA Audio mode, Please do enlighten me.
      As a result Internal Speaker, Internal Mic, and Headphone Jack doesn’t work.
       
      Touchpad on Travel Keyboard Dell K12a001 (Should work with DSDT Patch with pin configuration) I have no idea how. Obviously, Intel Wireless 7265 AC. For experimental purpose. https://github.com/daliansky/XiaoMi-Pro-Hackintosh/issues/330 — Knock yourself out. I managed to get it work for awhile but the real problem is kernel panic so I gave up. Ordering compatible card instead. ------------------
       
      Config.plist got it from Rehabman laptop config.
       
       
      BIOS version A20
       
      Enable:
       
      - Legacy Boot Rom
       
      Disable:
       
      - Secure Boot
       
      - TPM 2.0
       
      - Vt-d
       
      ------------
       
      SMBIOS - I use MacBook8,1. —- MacBookAir7,1-7,2 (Min Freq is at 1.2 GHz) MacBookPro12,1 Min Freq is at 800 Mhz and it is the default this cpu should be. Again, there is a way to set it right somewhere in this forum.
       
      ------------
       
      -->> DSDT Windows 8 patch
       
      System sees only one I2C Controller which control Touch Screen.
      Touch Screen registers as Magic Trackpad 2.
      Pen as Mouse
       
      -->> DSDT Windows 8.1 Patch
       
      System sees two I2C Controllers which control Touch Screen and Accelerometer.
      Touch Screen registers as Magic Trackpad 2.
      Pen as Mouse
       
      OOO>>> With Windows 8.1 patch which it should run with this one because it can see more of HID devices and controllers.
       
      Problem is Accelerometer (SHUB).
      Device can automatically rotate screen as it should be BUT it flips the screen wildly even with slightly movement. It stops only when device stays completely still. Eventually it breaks internal screen graphic. It becomes grabble. I restored internal screen graphic by connecting it to external monitor and set rotation of external screen to 0 degree. Then it is back to normal. (I guess it conflict with rotation setting) I disable SHUB in DSDT.
       
      ---------------------
       
      During Installation process Full Graphic acceleration can be activated straight away by Lilu and Whatevergreen. AppStore, iMessage and, FaceTime activate by NullEthernet and SSDT by Rehabman USBInjectAll needed for keyboard and other usb peripherals. Use other tool to keep certain ports active as Rehabman mention this KEXT is not good for a long run. Please do Correct me if I did something worng. Or any suggestions to make this thing runs better.
      CLOVER.zip
      IOReg_SysReport.zip
    • By midi-sama
      After a long time of cooking this computer up with a lot of stuff, I'm finally releasing my guide for this P50 with OpenCore.
       
      Lenovo ThinkPad P50 macOS Install with OpenCore
       
      This thread may be used for questions/corrections/additions. Good Luck.
    • By Georgiles
      Laptop: Asus Vivobook F510UA
      CPU: Intel Core i5-8250U
      Graphic: Intel UHD 620
      Wifi: Intel Dual Band Wireless-AC 8265 (no kexts for intel wifi) :(
      Card Reader: Realtek_CardReader(RTL8411B_RTS5226_RTS5227)
      Camera: ASUS UVC HD 7.Audio: Conexant Audio CX8050
      Touchpad: ELAN1300
       
       by parkrypto: thank you tctien342 for the amazing guide.
       
      https://github.com/tctien342/Asus-Vivobook-S510UA-High-Sierra-10.13-Hackintosh
       
      Ebayed the laptop for $290 + tax = $350
      added: 16gb RAM + existing 8GB = 24GB          Timetec Hynix IC 16GB DDR4 2400MHz PC4-19200 Non ECC Unbuffered 1.2V CL17 2Rx8 Dual Rank 260 Pin SODIMM Laptop Notebook Computer Memory Ram Module Upgrade S Series (16GB)     
      added: cheap wifi         TP-Link USB Wifi Adapter for PC N150 Wireless Network Adapter for Desktop - Nano Size Wifi Dongle Compatible with Windows 10/7/8/8.1/XP/Vista Mac OS 10.9-10.15 Linux Kernel 2.6.18-4.4.3 (TL-WN725N)     
      added: NAND 1TB Internal PC SSD https://www.amazon.com/gp/product/B073SB2MXT/ref=ppx_yo_dt_b_asin_title_o01_s01?ie=UTF8&psc=1
      Gadget Reviews upgraded too, video: https://www.youtube.com/watch?v=39EquX5PTkQ
       
      I just installed. Everything works fine. I'll test final cut pro, premiere pro with 4k footage and get back with you on performance. 
      For now moves like a performant Mac book pro. 
      I installed Catalina first but I could not make the Intel UHD 620 Graphics get proper QE/CI. 
      Mojave is just fine. I want to use this system for quick video editing on the go.
      Geekbench in my signature.  
      If you need any files or have any questions pls ask.
       






      asus f510u mojave.zip
    • By Sagnik Ganguly
      Hello I'm Sagnik Ganguly, I'm trying to dual boot macOS 10.14 and Windows 10 (already installed) on a PC with Legacy BIOS. I've two hard drives one in where the windows is installed and another which is converted to GPT to install macOS Mojave 10.14 with a partion of Mac OS Extended (Journal) or APFS but when I went to the Install Disk Selection page, I'm selecting the partition but it says "This version of macOS 10.14 cannot be installed on this computer." can you help me please? 
      P. S. My motherboard doesn't support UEFI. 
      I'm attaching some pictures of the screens.


×