Jump to content
ludufre

[Guide] Gigabyte GA-Z370N-WIFI + i7 8700K + UHD 630 + Mojave 10.14.6

51 posts in this topic

Recommended Posts

Hello,

my setup is a bit different from yours:

- Gigabyte z370N

- i5-8600

- Samsung EVO 970

- G.Skill 16GB

- wifi BCM94352Z

 

followed your exact instructions but stuck at booting from USB drive.

When I boot up, I choose USB disk and get the CBM and choose install MAC from USB. I see a white apple logo for about few seconds and then it just reboots.

Enabled verbose boot log, please see attached - i can't figure out nothing from it.

 

 

WhatsApp Image 2018-10-28 at 20.27.32.jpeg

Share this post


Link to post
Share on other sites
Advertisement
7 hours ago, TheMaxx32000 said:

bios f5 settings @Luan Eduardo

bios_set_f5

 

Have tried F5 (not the one you've supplied, original one) and F10 - cannot boot to OS.

F1 is working, but the fan stops working after few minutes and system cpu gets ver hot!!! wtf???

any ideas?

 

Share this post


Link to post
Share on other sites

We should probably wait for the new Mac Mini 2018 macOS build as it uses HDMI 2.0 and DP while featuring the exact same desktop coffee lake cpus that we're using.

 

currently downloading 10.14.1 build 18B2107 from apple to see if there is something of interest in there..

Share this post


Link to post
Share on other sites

Hi everyone, I'm just going to tell you that I'm kind of abandoning this project. The macOS is only starting with the BIOS / EFI in the F1 version, but in this version I have problems with the memory modules that compels me to use F2 up. I tried all Aptio drivers imaginable, but to no success. From now on I will have to accept running macOS in Windows VMware :(

Share this post


Link to post
Share on other sites

Re: the DP here is how I got mine working on 2 separate instances. I may be helpful to someone.

Went through the install process and all using the htmi, plugged the DP and I got the second display. Took out the hdmi and left with only DP display working.

On boot the DP goes off...but if I wait few seconds till the boot process reaches the login screen turns on again and it works ok. 

 

Share this post


Link to post
Share on other sites
On 10/29/2018 at 12:04 AM, kisyu said:

Hello,

my setup is a bit different from yours:

- Gigabyte z370N

- i5-8600

- Samsung EVO 970

- G.Skill 16GB

- wifi BCM94352Z

 

followed your exact instructions but stuck at booting from USB drive.

When I boot up, I choose USB disk and get the CBM and choose install MAC from USB. I see a white apple logo for about few seconds and then it just reboots.

Enabled verbose boot log, please see attached - i can't figure out nothing from it.

 

 

WhatsApp Image 2018-10-28 at 20.27.32.jpeg

Hi,

 

I had the exact same issue that you have after using for a few days.

Even my macOS installer was stuck at ---End Randomseed----- too. I thought it was an issue with kexts or any files in driver64UEFI. I even spent 2 days blaming and resetting my BIOS, but I was wrong since the culprit was config.plist

 

I made some changes in the config.plist file generated by Clover EFI Bootloader along with what was recommended in the OP. I don't remember the exact changes since I was just testing it out to make it work somehow.

 

I even updated my BIOS to F10 & it works without any issue.

Anyway, attaching my config.plist. Try replacing it with yours & if any luck it might just work.

config.plist

Share this post


Link to post
Share on other sites

This is my new Macmini8,1 config. Missing SMBIOS values are:

  • FirmwareFeatures
  • FirmwareFeaturesMask
  • PlatformFeature
  • BiosVersion

I did add values in SSDT-2-A M I to match the original Macmini8,1 such as

  • graphic-options
  • AAPL,gray-value
  • AAPL,gray-page
  • AAPL,GfxYTile
  • AAPL,ig-platform-id

I also did remove Whatevergreen.kext. BIOS is still F5 (settings are unchanged from my previous post).

 

The original Macmini8,1 was running 10.14.1 (18B75) with ig-platform-id 0x3e9b0007.

 

CLOVER.zip

Edited by TheMaxx32000

Share this post


Link to post
Share on other sites
2 hours ago, TheMaxx32000 said:

This is my new Macmini8,1 config. Missing SMBIOS values are:

  • FirmwareFeatures
  • FirmwareFeaturesMask
  • PlatformFeature
  • BiosVersion

I did add values in SSDT-2-A M I to match the original Macmini8,1 such as

  • graphic-options
  • AAPL,gray-value
  • AAPL,gray-page
  • AAPL,GfxYTile
  • AAPL,ig-platform-id

I also did remove Whatevergreen.kext. BIOS is still F5 (settings are unchanged from my previous post).

 

The original Macmini8,1 was running 10.14.1 (18B75) with ig-platform-id 0x3e9b0007.

 

CLOVER.zip

I'm getting this using this clover

IMG_20181107_170235.jpg

IMG_20181107_170242.jpg

Edited by registracii

Share this post


Link to post
Share on other sites

Typical of what happens when you loose your USB 2 or 3.

Trying different USB ports sometimes will sometimes kick it back to life, meaning some USB ports may still be working.

You need to make a custom SSDT for your USB ports or customise USBInjectAll.kext

Good luck

 

Share this post


Link to post
Share on other sites
12 hours ago, khamsakamal48 said:

Seems like you are using USB 3.0 port during installation, are you? If so, try with a USB 2.0 port.

 

 

12 hours ago, STLVNUB said:

Typical of what happens when you loose your USB 2 or 3.

Trying different USB ports sometimes will sometimes kick it back to life, meaning some USB ports may still be working.

You need to make a custom SSDT for your USB ports or customise USBInjectAll.kext

Good luck

 

 

Sorry I had to give more info. I have Mojave installed already. This is not installation, I'm just booting. There's no usb involved that's why I decided to share. 

Edited by registracii

Share this post


Link to post
Share on other sites
On 11/7/2018 at 12:11 PM, TheMaxx32000 said:

This is my new Macmini8,1 config. Missing SMBIOS values are:

  • FirmwareFeatures
  • FirmwareFeaturesMask
  • PlatformFeature
  • BiosVersion

I did add values in SSDT-2-A M I to match the original Macmini8,1 such as

  • graphic-options
  • AAPL,gray-value
  • AAPL,gray-page
  • AAPL,GfxYTile
  • AAPL,ig-platform-id

I also did remove Whatevergreen.kext. BIOS is still F5 (settings are unchanged from my previous post).

 

The original Macmini8,1 was running 10.14.1 (18B75) with ig-platform-id 0x3e9b0007.

 

CLOVER.zip

 

@TheMaxx32000 Thank you, dude! Thank you very much! Finally I was able to start without getting stuck in the F1 BIOS, I am currently in F10!

 

Now, as I like to learn things, I'm going to extract my original DSDT / SSDT and find out which patches you applied by comparing the .AML files. I like to leave everything documented.

 

I'm just having problems now that my BCM94352Z wireless card and my NVME disk are not recognizing it, but I'll fix later. That is not a big problem.

 

Thank you, again.

 

On 11/7/2018 at 3:09 PM, registracii said:

I'm getting this using this clover

IMG_20181107_170235.jpg

IMG_20181107_170242.jpg

 

I have the same issue if not put de ACPI/patched folder provided by TheMaxx32000. Or you have a different processor?

Share this post


Link to post
Share on other sites
2 hours ago, Luan Eduardo said:

I have the same issue if not put de ACPI/patched folder provided by TheMaxx32000. Or you have a different processor?

oh yep...i58600

Share this post


Link to post
Share on other sites

Hi there,

 

I have managed to install hackintosh on my computer finally. But I ma having black screen flickering issues, and none of the DP outs work on, I am not sure what to do about about. My specs are:

 

OS: 10.14.3

Mobo: Z370n WiFI

CPU: i7 9700K

GPU: AMD RX 580 OEM version

Storage: Samsung 970EVO

 

Any sort of help is appreciated.

 

 

Share this post


Link to post
Share on other sites
On 2/2/2019 at 12:20 PM, gizlin said:

Hi there,

 

I have managed to install hackintosh on my computer finally. But I ma having black screen flickering issues, and none of the DP outs work on, I am not sure what to do about about. My specs are:

 

OS: 10.14.3

Mobo: Z370n WiFI

CPU: i7 9700K

GPU: AMD RX 580 OEM version

Storage: Samsung 970EVO

 

Any sort of help is appreciated.

 

 

 

If you are using same SMBIOS as me then the problem is with de AMD graphic injection.

With that I can not help.

Share this post


Link to post
Share on other sites
2 hours ago, ludufre said:

 

If you are using same SMBIOS as me then the problem is with de AMD graphic injection.

With that I can not help.

 

Any idea what could be done to fix the situation?

Share this post


Link to post
Share on other sites
5 minutes ago, gizlin said:

 

Any idea what could be done to fix the situation?

 

I never have a luck with discrete card. I'll suggest you try without the card.

Share this post


Link to post
Share on other sites
On 10/18/2018 at 3:25 AM, TheMaxx32000 said:

Hi @Luan Eduardo

 

please find my clover folder attached – I set up everything to use as little patching as possible.

 

DP and secondary eth work (needs modded FakePCIID_Intel_GbX.kext + SmallTreeIntel82576.kext) – running in dual-4k@60hz over here.

 

Also added ig-platform-id through ssdt-2 and some cosmetics (built-ins, device names etc).

 

Also all USB ports, including the front USB3.0 ones, work as expected.

 

Credits to @MaLd0n for the initial patched dsdt-version.

 

CLOVER.zip

 

screenshot_dual4k60.thumb.png.e892d2d45790e027af974ef00b7b3139.pngscreenshot_dual4k60-2.thumb.png.022d6070b57dee1a8801da2c47f1ce1a.png

 

Did you ever figure out if you still need whatevergreen and FakePCIID_Intel_GbX.kext for the display port to work? Also, how is the Mac Mini 8,1 SMBIOS vs the iMac 18,1?

Share this post


Link to post
Share on other sites

Hi, i have a strange issue with HDMI audio (seems regardless of which port i use).

 

i use an HDMI switch to cycle between various devices, one of which is my hack. if i put the hack to sleep without hdmi output connected, i have no HDMI audio after i wake up the machine. the issue persists, even re-attaching the cable wont help, so i have to reboot to get back sound.

 

the issue can be replicated by simply unplugging the hdmi cable before the putting the machine to sleep.

 

i am using layout-id=7 and the most recent versions of Lilu, AppleALC and WhatEverGreen (as of this post). I also played around with darkwave but this does not make any difference (currently set to 8).

 

besides this issue, hdmi is working fine, even when i put the machine to sleep with leaving the monitor attached. i am wondering if u could do me a favor and briefly test the above scenario.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By hungdv
      Hello guys,
      I was try to install MacOS Mojave on my new machine but no luck. Can anyone show me which guide to fit my system, please?please?please?
      + Mobo: GIGABYTE Z390 AORUS ELITE LGA1151v2
      + CPU: Intel Core i5-9600K 3.7GHz
      + iGPU: Sapphire RX 580 Pulse 8GB
      + Drives: SSD Samsung 970 Pro PCIe NVMe V-NAND M.2 2280 512GB
      + Ram: Crucial Ballistix Sport LT 2x8GB Bus 2666 DDR4
      + PSU: Corsair RM650 80 Plus GOLD
      + Case: Corsair 220T White RGB Airflow Tempered Glass
      + Cooler: Cooler Master HYPER 212 BLACK EDTION
      + Dual Band Network Card Broadcom Bcm94360 867Mbps.
    • By Rajan Pandit
      Hai, I have,
      i5 2500k
      GA-z68 AP D3 Rev.1
      Corsair 8 GM Ram
      Gigabyte Radeon RX 560 OC 4G Graphic Card
      500 GB Samsung SSD EVOf
       
      with this configuration I tried to install Mojave but After Apple Logo there was a black screen
      then nothing... please help
      I have create USB with terminal and Install Clover_v2.4k_r4961-Legacy.pkg to activate boot
      then I have recessary kext to EFI/KEXT/OTHER 
      but I am struck at Black Screen after apple logo
    • By Rajan Pandit
      Hai, I have,
      i5 2500k
      GA-z68 AP D3 Rev.1
      Corsair 8 GM Ram
      Gigabyte Radeon RX 560 OC 4G Graphic Card
      500 GB Samsung SSD EVO
      .. I want to install Mojave on this configuration...
      please help. what I need to do... 
      I have downloaded the Installer from APP Store...
      please help
    • By ScoobDoob69
      Hi, everyone so I am currently dual-booting Windows 10 and Linux Mint. I would like to add Mojave and triple boot (without formatting/losing all data from windows and linux).
       
      My Current Specs:
      CPU: Intel Core i7-2600 (not k) Sandy Bridge
      GPU: Aorus Radeon RX570 4GB
      Motherboard: Intel SWQ6710H
      HDD: 4TB Western Digital Blue WD40EZRZ
      Ram: 20GB DDR3 Total (2x 8GB + 2x 2GB)
       
      1. Is it possible to install Mojave on my HDD without wiping Windows 10 or Linux Mint?
      2. What guide is most ideal for my situation? 
       
      If you need any additional information or details, I am more than happy to provide that. I tried multiple guides months ago and could not get the installation to work. 
       
       
    • By MaLd0n
      ---TUTORIAL---

      https://olarila.com/forum/viewtopic.php?f=50&t=8685
       
      --Original Post--
       
      https://olarila.com/forum/viewtopic.php?f=97&t=11237
       
      --Bios/UEFI Settings--
       
      *Update bios/uefi to F7+*
      1- Go to M.I.T./Advanced Frequency Settings tab
       
      Extreme Memory Profile (X.M.P.) - Profile 1
       
      2- Go to BIOS tab
       
      CSM Support - Disabled
       
      3- Go to Peripherals/Thunderbolt(TM) Configuration tab
       
      Security Level - No Security
      Thunderbolt USB Support - Enabled
      GPIO3 Force Pwr - Enabled
       
      4- Go to Chipset tab
       
      Internal Graphics - Enable
       
      ---CLOVER FOLDER---
      https://olarila.com/files/Clover.Folder/EFI CLOVER Z390 DESIGNARE.zip
      *Use this folder with FULL DSDT PATCHED
       
      ---OPENCORE FOLDER---
      https://olarila.com/forum/download/file.php?id=24376
      *Use this folder with FULL DSDT PATCHED
       
       
      ---Extract one Full dump for DSDT edits, post files---
       
      RunMe.app
       
       
       
      ---HARDWARE---
       
      --MOBO

      GIGABYTE Z390 DESIGNARE
      -Link
      https://www.amazon.com/Z390-DESIGNARE-Gigabyte-Thunderbolt-Motherboard/dp/B07K8RJZRG/ref=sr_1_1?keywords=Z390+DESIGNARE&qid=1565492390&s=electronics&sr=1-1

      --PROCESSOR

      Intel Core i9-9900K
      -Link
      https://www.amazon.com/Intel-i9-9900K-Desktop-Processor-Unlocked/dp/B005404P9I/ref=sr_1_1_sspa?keywords=Intel+Core+i9-9900K&qid=1553358099&s=gateway&sr=8-1-spons&psc=1

      --COOLER

      CORSAIR H100i RGB PLATINUM AIO Liquid CPU Cooler
      -Link
      https://www.amazon.com/CORSAIR-H100i-PLATINUM-Liquid-Cooler/dp/B07JWB5BSN/ref=sr_1_4?keywords=WATER+COOLER+CPU&qid=1565492509&s=gateway&sr=8-4

      --MEMORY

      Corsair CMW32GX4M2C3200C16 Vengeance RGB PRO 32GB (2x16GB) DDR4 3200 (PC4-25600)
      -Link
      https://www.amazon.com/Corsair-CMW32GX4M2C3200C16-Vengeance-PC4-25600-Desktop/dp/B07GTG2T7L/ref=sr_1_15?keywords=memory+ddr4+32&qid=1553358238&s=gateway&sr=8-15

      --GPU

      MSI RX Vega 64 AIR Boost 8G OC
      -Link
      https://www.amazon.com/MSI-RX-64-AIR-8G/dp/B07DH7S1X1/ref=sr_1_2?keywords=vega+64+gigabyte&qid=1565492819&s=electronics&sr=1-2

      --SSD

      Samsung 970 EVO 1TB SSD (MZ-V7E1T0BW) NVMe M.2 V-NAND
      -Link
      https://www.amazon.com/Samsung-970-EVO-1TB-MZ-V7E1T0BW/dp/B07BN217QG/ref=sr_1_1?keywords=s+samsung+970+evo+1tb&qid=1565493002&s=electronics&sr=1-1

      --POWER SUPPLY

      EVGA Supernova 1000 P2 80+ Platinum, 1000W ECO Mode Fully Modular 
      -Link
      https://www.amazon.com/EVGA-Supernova-Platinum-Crossfire-220-P2-1000-XR/dp/B00EKJQM5E/ref=sr_1_3?keywords=power+supply+1000w&qid=1565493196&s=gateway&sr=8-3

      --WIRELESS

      TP-Link Archer T9E
      -Link
      https://www.amazon.com/TP-Link-Archer-T9E-Beamforming-Technology/dp/B00TQEX7AQ/ref=sr_1_1?keywords=TP-Link+Archer+T9E&qid=1553358397&s=gateway&sr=8-1

      --CASE

      Thermaltake Core P5 Tempered Glass Black Edition ATX Open Frame Panoramic Viewing
      -Link
      https://www.amazon.com/Thermaltake-Tempered-Panoramic-Certified-CA-1E7-00M1WN-03/dp/B01N4IGVSC/ref=sr_1_2?keywords=Thermaltake+Core+P5&qid=1565493567&s=gateway&sr=8-2

      --DSDT Patches--
      -FIX ACPI ERRORS -FIX OEM SSDTs to AVOID ERRORS AND WARNINGS -REMOVE UNUSED SCOPES / DEVICES -HIGH PRECISION EVENT TIMER -SATA -DMAC -REMOVE PROBLEMATIC AND UNUSED DEVICES -FIX K.P in REBOOT -SLPB -DARWIN / WINDOWS 2015 -XHCI -PLUGIN TYPE -HDAS to HDEF -HDEF -REAL TIME CLOCK -ARTC -IRQs -SBUS -BUS1 -MCHC -ALS0 -SHUTDOWN -LAN -FWHD -USBX -PMCR -PPMC -XSPI -CNVW -GMM -IMEI -EC -PNLF -ARPT -GFX0 -NVME -DTGP -ACQUIRE MUT0 0XFFFF -MUTEX MUT0 0x00 -EXTERNAL REFERENCES -UNKNOWNOBJ -HDMI / HDAU -FULL RENAMED DEVICES ---SCREENSHOTs---




















      -Credits and thanks to the old and new people in the community who developed patches, kexts and bootloaders!
      Thanks to KGP for SSDT Thunderbolt
      Slice, Kabyl, usr-sse2, jadran, Blackosx, dmazar, STLVNUB, pcj, apianti, JrCs, pene, FrodoKenny, skoczy, ycr.ru, Oscar09, xsmile, SoThOr, RehabMan, Download-Fritz, Zenit432, cecekpawon, Intel, Apple, Oracle, Chameleon Team, crazybirdy, Mieze, Mirone, Oldnapalm, netkas, Elconiglio, artut-pt, ErmaC, Pavo, Toleda, Master Chief and family, bcc9, The King, PMheart, Sherlocks, Micky1979, vit9696, vandroiy2013, Voodoo Team, Pike R. Alpha, lvs1974, Austere.J, CVad, Sampath007, onemanosx, erroruser, Jenny David, Olarila Facebook Community, Hackintosh Facebook Community and many others!
      We're all here to have fun and learn from each other!
×