Jump to content
KGP-iMacPro

iMac Pro X99 - live the future now with macOS 10.14 Mojave [Successful Build/Successful Guide]

107 posts in this topic

Recommended Posts

 

iMacPro-X99.thumb.png.658514b282b350d5c069e64a51fa70e7.png

 

Up and running  macOS Mojave 10.14.4 (18E226) on my Broadwell-E/X99 iMac Pro Hackintosh! 

 

X99-10_14.4.thumb.png.1cdb426955ff7c7c88f9c9f8dc2eb433.png

 

84619521_Screenshot2018-06-06at11_25_03.png.9ad705b76c3b7f7ab443b276fb8b7585.png

 

This afternoon @DSM2 advised me that yesterday Apple seems to have added a second special build of MacOS 10.14.4 (18E2034) on swcdn.apple.com, likely for new devices.

 

1365135151_Screenshot2019-03-26at23_53_16.png.b1c27e856fdd018f58e55afbc4cb6403.png

 

1140000163_Screenshot2019-03-26at23_54_11.png.67496c76f09abd0b56eb9bfa79cf5538.png

 

 

Abstract and Introduction: 

This originating post constitutes an innovative and brand new iMac Pro macOS 10.14 Mojave Build and Desktop Guide for Broadwell-E/EP, Haswell-E/EP and X99, which certainly will further grow not only thanks to your estimated feedback and contributions. It is the logical continuation of my successful iMac Pro Broadwell-E/EP, Haswell-E/EP and X99 Build and Desktop Guide published for macOS High Sierra 10.13 in the other forum. Being an iMac Pro Desktop Guide, it has also large similarities with my Skylake-X/X299 iMac Pro macOS 10.14 Mojave Desktop GuideHowever, to avoid jumping back and forth, I will make this guide as consistent as the other, which however implies also some redundancy.    

 

As everybody already might know, my Broadwell-E/EP, Haswell-E/EP and X99 Desktop Guides base on the ASUS X99-A II. However, also other X99 ASUS mainboard models or X99 mainboards of other brands might be compatible after likely considering and implementing few mandatory modifications. The same states for guide compatibility with all Broadwell-E/EP and Haswell-E/EP CPUs different form the i7-6950X employed here. 

 

Before starting with all detailed instructions, please find a Table of Content that provides an overview of the individual topics addressed within this guide:
 
--------------------------------------------------------------------------------------------------------------
 
Table of Contents: 
 
A.) Hardware Summary 
 
B.) ASUS Mainboard BIOS
B.1) ASUS BIOS Firmware Patching
B.1.1) CPU Microcode Update
B.1.2) MSR 0xE2 register unlock for OSX Kernel Write 
B.2) ASUS X99-A II BIOS Configuration
 
C.) Important General Note/ Advice and Error Prevention  
 
D.) iMac Pro macOS 10.14 Mojave System Setup
This chapter includes a general guideline how to perform the initial setup of a Broadwell-E/EP, Haswell-E/EP, X99 iMac Pro with macOS Mojave DP1 (18A293u). 
 
D.1) iMac Pro EFI-Folder Preparation
D.2) iMac Pro macOS Mojave Installer Package Creation
D.3) iMac macOS Mojave USB Flash Drive Installer Creation
D.4) iMac Pro macOS Mojave Clean Install on Broadwell-E/EP, Haswell-E/EP, X99
D.5) Direct iMac Pro conversion of a functional Broadwell-E/EP, Haswell-E/EP, X99 system with a SMBIOS System Definition different from iMac Pro1,1 and a standard macOS build implementation. 
D.6) iMac Pro macOS High Sierra Build Update Procedure
 
E.) Post Installation Process
E.1) Xnu CPU Power Management (XCPM) Configuration
E.2) Graphics Configuration
E.3) Audio Configuration
E.4) USB Configuration
E.5) M.2/NVMe Configuration
E.6) SSD/NVMe TRIM Support
E.7) GC-Titan Ridge / GC-Alpine Ridge /Asus TBEX 3 PCIe Add-In Implementation
E.8) Gbit and 10-Gbit Ethernet Implementations
E.8.1) ASUS X99-A II on-board Gbit Ethernet Functionality
E.8.2) 10-Gbit LAN Implementations
E.8.2.1) ASUS XG-C100C Aquantia AQC107 10-Gbit NIC
E.8.2.2) Intel X540-T1 10-Gbit NIC
E.8.2.3) Small-Tree P2EI0G-2T 10-Gbit NIC
E.8.2.4) NetGear ProSave XS508M 8-port 10-Gbit Switch
E.8.2.5) QNAP TS-431X2 Quad-core 4-Bay NAS tower
E.8.2.6) 10-GBit Ethernet Optimisation
E.9) ASUS X99-A II PCI Device Implementation
E.9.1)  ACPI DSDT Replacement Implementation
E.9.2) System SSDT PCI Device Implementation
E.9.2.1) HDEF - onboard Audio Controller PCI Implementation
E.9.2.2) GFX0, HDAU - GPU and HDMI/DP Audio PCI implementation
E.9.2.3) XGBE - 10GBit NIC PCI Implementation:
E.9.2.4) ETH0 - onboard LAN Controller PCI Implementation
E.9.2.5) SAT1 - Intel AHCI SATA Controller PCI Implementation
E.9.2.6) EVSS - Intel X99 sSata Controller PCI Implementation
E.9.2.7)  ANS1 - NVMe Controller PCI Implementation
E.9.2.8) - USBX:
E.9.2.9) XHCI - onboard Extended Host Controller Interface (XHCI) PCI Implementation
E.9.2.10) XHC2 - ASMedia ASM1142 USB 3.1 Controller PCI Implementation
E.9.2.11) ARPT - OSX WIFI Broadcom BCM94360CD 802.11 a/b/g/n/ac + Bluetooth 4.0 AirPort Controller PCI Implementation:
E.9.2.12)  GC-Titan Ridge / GC-Alpine Ridge / Asus TBEX 3 Thunderbolt HotPlug System Implementation
E.9.2.13) DTGP Method
E.9.2.14) - Debugging Sleep Issues
E.10) iMac Pro Boot Splash Screen Cosmetics
E.11) iMac Pro Desktop Background cosmetics
E.12) iStatMenus Hardware Monitoring
 
F.) Benchmarking
F.1) i7-6950X CPU Benchmarks
F.2) Sapphire Nitro+ Radeon RX Vega 64 8GB OpenGL and Metal Benchmarks
 
 
G.) Summary and Conclusion 
 
--------------------------------------------------------------------------------------------------------------
 

A.) Hardware Summary

 

Motherboard: Asus X99-A II

CPU: I7-6950X (10-core)
RAM: 128 KIT (8X16GB) G.Skill TridentZ (F4-3200C14Q2-128GTZSW)
System Disk: Samsung 850 EVO 1TB (SSD) / Samsung 960 EVO 1TB (NVMe, M.2)
RAID: 3x Western Digital Red Pro 6TB (18TB);
Thunderbolt 3 Add-in: GC-Titane Ridge 40GB/s Intel Thunderbolt 3 Certified Add-in PCIe Adaptor
Wifi + Bluetooth: OSXWIFI PC/Hackintosh - Apple Broadcom Bcm9436cd - 802.11 A/B/G/N/AC +Bluetooth 4.0 PCIe
Power Supply: Corsair AX860
CPU Cooler: Corsair H80i v2
Webcam: Logitech HD Pro WebCam C930
Monitor: LG 38UC99-W, 38", WQHD, 21:9, 3840x1600 pixel, 75 Hz.
Case: Corsair CC600TWM-WHT, Graphite Series 600T, Mid Tower
Keyboard: Logitech K811
Mouse: Logitech Ultra-Thin Touch Mouse T631
Blu-Ray/DVD Writer: LG Super Multi Blue BH16 (BH16NS55)
 
Thunderbolt: ASUS TBEX 3 and Gigabyte Alpine Ridge
 
10Gbit Ethernet components:
- 1x ASUS XG-C100C AQC107 PCIe x4 10GBit LAN Adapter (for testing purposes)
- 1x Intel X540-T1 single port 10GBit LAN PCIe Adapter (for testing purposes, now installed in my X99 rig)
- 1x Small-Tree P2EI0G-2T 2-Port 10GBit LAN PCIe Adapter (now default configuration)
- 1x NetGear ProSave XS508M 8-port 10GBit switch
- 1x QNAP TS-431X2 Quad-core 4-Bay NAS tower with Built-in 10GbE SFP+ Port and 4x 12 TB Seagate IronWolf in RAID 0 configuration.
 
Let me express my gratitude to @gxsolace at this place for providing me with 1x Intel X540-T1, 1x Small-tree P2EI0G-2T and 4x 12 TB Seagate IronWolf hardware.
 
B.) Asus Mainboard BIOS
 
Please find below a detailed instruction for ASUS X99 mainboard BIOS Firmware patching, as well as a summary of my actual Asus X99-A II  BIOS settings.
 
B.1) Asus Mainboard BIOS Firmware Patching
 
B.1.1) CPU Microcode Update
 
Not every BIOS firmware provided by the different Mainbaord manufacturers always accounts for all CPU microcodes distributed by Intel. Recently we witnessed for instance along the latest macOS 10.13 High Sierra distributions and even during the first macOS Mojave 10.14 distribution a Broadwell/Haswell CPU performance issue (no overclocking) in combination with most X99 mainboard implementations to be traced back a missing Intel CPU microcode implementation in most of the distributed Mainbaord BIOS firmwares. To overcome the OC issue, an Intel CPU microcode update within the respective BIOS firmware distributions is absolutely vital and mandatory. 
 
How to perform the Intel CPU microcode update for a given BIOS firmware distribution e.g. under Windows 10 is detailed below for the ASUS X99-A II 1902 BIOS firmware distribution. The same approach, initially provided and described by @michaeljeger (once more many thanks from all of us :thumbsup_anim:) can be applied to any other BIOS Firmware distribution of any mainboard manufacturer. 
 
In Windows 10, download the latest UBU software distribution from https://cloud.mail.ru/public/HLDj/6cT1gUPke:
 
a.) From online directory "UEFI BIOS Updater" download und unrar "UBU_v1_70_rc12.rar" or any newer distribution to an "UBU" directory on your Windows Desktop yet to be created  
 
b.) Also download and unrar "mms.tar" from the online directory "UEFI BIOS Updater". This will create an "mmt" folder, where from the "5.2.0.24" directory you copy "MMTool.exe" to your "UBU" Desktop directory 
 
c.) Download the latest BIOS firmware distribution for your particular mainboard from the respective web page of your mainboard manufacturer. In case of the ASUS X99-A II, it is X99-A-II-ASUS-1902.CAP. Copy the respective BIOS Firmware file to your "UBU" Desktop directory. 
 
Now you have all necessary ingredients in your "UBU" Desktop directory. 
 
d.) Open a windows terminal, change to the "UBU" Desktop directory and launch the UBU software with the terminal command:
 
ubu 

 

On UBU software launch, UBU will now scan your BIOS firmware file that you previously added to your "UBU" Desktop directory and detect BIOS platform, manufacturer and mainboard model, as well as EFI Driver and OROM components.
 
UBU0.PNG.f8b149434ca88b84189d2418b1b59b65.PNG
 
When you are asked to "Press any key to continue..", follow this request.  
 
e.) From the listed options in the consecutive terminal text menu
 
UBU1.PNG.df678f28cbe814270f7fda17220fabf4.PNG
 
choose option 5 - CPU Microcode  by typing "5" and subsequently pressing the "Enter" button.
 
f.) Now the tool will analyse whether are not all respective available CPU microcodes are properly implemented in your BIOS firmware. All implemented CPU microcodes will be highlighted by "YES", all missing CPU microcodes will be highlighted by "No".
 
UBU3.thumb.PNG.7db66aa3d6706c92e89796d3570d68dd.PNG
 
To download the missing Intel CPU microcodes, choose option "C - Create FFS with MicroCodes" by typing "C" and subsequently pressing the "Enter" button. 
 
g.) In the next terminal text menu the tool will summarise all additional downloaded Intel CPU microcodes:
 
UBU4.thumb.PNG.34d31efd2669255be0c40cfcdc6b6b2e.PNG
 
 
To implement the new and complete set of available Intel CPU microcodes in your BIOS firmware file, launch "MMTool", which you previously added to your "UBU" desktop directory, by typing "M" and subsequently pressing the "Enter" button. 
 
h.) Now MMTool now will do it's magics and summarise once more the complete Intel microcode table successfully implemented in your BIOS firmware file.
 
UBU5.thumb.PNG.17f2d29150b4baea688761c517205f3e.PNG
 
Now choose menu option "0 - Exit to Main Menu" by pressing "0" and subsequently "Enter".
 
i.) In the next terminal text menu choose "Rename to ASUS USB BIOS Flashback" by pressing "1" and subsequently "Enter".
 
UBU6.thumb.PNG.9f36d1047345670cfce17d514ae494be.PNG
 
By this, the UBU tool will save the modified BIOS firmware file in the "UBU" desktop directory already with the correct EZ Flashback convention. For mainboards different from ASUS, this last step might be different though. We have to wait on further user feedback.  In case of our ASUS X99-A II 1902 BIOS firmware, we will find X99A2.CAP as the result of the UBU Intel CPU microcode procedure.  
 
After providing our firmware with a complete set of Intel microcode implementations, we can now continue with the firmware patching procedure and unlock the MSR 0xE2 register for OSX Kernel write.
 
 
B.1.2) MSR 0xE2 register unlock for OSX Kernel Write 
 
On a real Mac with native OSX XCPM power management, the MSR 0xE2 register is unlocked and therefore writeable. However, on ASUS mobos this register is usually read only. This is also the case for all ASUS X99 mobos. When the kernel tries to write to this locked register, it causes a kernel panic. This panic can happen very early in the boot process, with the result that your system freezes or reboots during the boot process. We can circumvent the MSR 0xE2 register write with a dedicated KernelToPatch entry in the config.plist, namely "xcpm_core_scope_msrs © Pike R. Alpha" and by enabling the "KernelPM" in the config.plist in Section "Kernel and Kext Patches" of the Clover Configurator. See Section E.1) for further details.
 
However, thanks to CodeRush's Longsoft UEFIPatch distribution and sophisticated MSR 0xE2 Register patches, we are able to successfully patch any ASUS X99 mainboard BIOS distribution and unlock the MSR 0xE2 register. This makes the "xcpm_core_scope_msrs © Pike R. Alpha" KernelToPatch entry obsolete and allows full native read/write MSR 0xE2 register access by the OSX kernel. The patched ASUS mainboard BIOS firmware finally can be uploaded each specific ASUS X99 mainboard by means of the ASUS EZ BIOS Flashback Procedure.
 
The individual steps for the ASUS X99 BIOS Patching are detailed below:
 
1.) Download and unzip the CodeRush's UEFI patch (attached towards the bottom of this guide) to your Desktop.
 
2.) To unlock the MSR 0xE2 register for kernel write copy the BIOS firmware file modified in section B.1.1)  to the "UEFIPatch_0.3.9_osx" directory on your Desktop.
 
3.) Open a terminal; type "cd " and drag the "UEFIPatch_0.3.9_osx"-folder on your Desktop into the Terminal window and press "Enter". One can also use the terminal command equivalent:
cd ~/Desktop/UEFIPatch_0.3.9_osx/

Note that this step is important to successfully execute the UEFI-Patch procedure! You must be in the UEFIPatch directory on your terminal, in order to successfully execute step 5.) below!

 
Once in the UEFIPatch directory on your terminal, drop the "UEFIPatch"-executable into the terminal window; Also drop the actual BIOS CAP file into the terminal window; Press enter to execute the "UEFIPatch"-procedure.
 
The equivalent terminal command in case of the ASUS X99-A II BIOS firmware is:
./UEFIPatch X99A2.CAP

For other mobos, please adapt the adequate BIOS CAP-filename in the command!

 

During the patch procedure, you will see something like the following message, which can be simply ignored:
parseImageFile: Aptio capsule signature may become invalid after image modifications
parseSection: section with unknown type 52h
parseFile: non-empty pad-file contents will be destroyed after volume modifications
parseSection: section with unknown type 52h
parseFile: non-empty pad-file contents will be destroyed after volume modifications
patch: replaced 6 bytes at offset F69h 0FBA6C24400F -> 0FBA7424400F
Image patched

 

6.) You will now find a "***.CAP.patched" BIOS-file in the UEFIPatch folder, which is your patched (MSR 0xE2 unlocked) BIOS file.
 
7.) Rename the "***.CAP.patched BIOS" file again to X99A2.CAP or to the correct EZ Flashback filename for your particular ASUS Mainbaord by following the ASUS BIOS Flashback filename convention.
 
8.) Copy the X99A2.CAP (or it's derivative in case you use a different ASUS mobo) to a FAT-formatted USB2.0 storage device.
 
9.) Shut-down your hack, connect the USB2.0 storage device to the USB-port assigned to the ASUS BIOS Flashback procedure (see the mobo manual for details). Press the BIOS-Flashback button for three seconds until the flashback-led starts to blink, indicating that the BIOS Flashback is in progress. Release the button. The locations of the BIOS-Flashback button and the USB-port assigned to the BIOS-Flashback procedure on the ASUS X99-A II are indicated in the figure below:
 
Flashback.png.b61e6bbf00604d44575da506ff91a8be.png
 
10.) Wait until the Flashback-led stops blinking and turns off, indicating that the BIOS Flashback process as been successfully completed. You now successfully installed the actual patched BIOS, compatible with native OSX/MacOS power management.
 
11.) Boot your system and apply the BIOS settings described below.
 
Instead of stepwise applying the entire Bios firmware patching procedure detailed above, all  ASUS X99A-II users can simply download, unzip and flash X99A2.CAP.zip, actual BIOS firmware 1902, accounting for the complete set of available Intel CPU Microcodes, an unlocked MSR register and an iMac Pro Splash Screen Boot Image to be displayed at boot.
 
B.2) Asus X99-A II BIOS Configuration
 
To overclock your RAM memory in concordance with your RAM specifications, enable the EZ XMP Switch on your ASUS Mainboard and enable posteriorly XMP in the Standard ASUS BIOS Setup mode (F7). Subsequently switch from standard to advanced ASUS BIOS Setup mode by pressing again F7.
 
BIOS-Settings.thumb.png.dd98bd610b3f5c8ae1a02c1c4096d7b1.png
 
Important Note:
 
"ASUS MultiCore Enhancement": When set to "Auto", MCE allows you to maximise the overclocking performance optimised by the ASUS core ratio settings. When disabled, MCE allows to set to default core ratio settings.
 
"Sync All Cores": Tremendous increase in CPU performance can be achieved with the CPU Core Ratio set to "Sync All Cores". In case of i9-7980XE stock settings (4.4 Ghz, Sync All Cores), the Geekbench score difference is approx. 51.000 (disabled) compared to 58.000 (enabled)! Note however, that Sync All Cores should be used only in case of the availability of an excellent water cooling system! Otherwise, CPU Core Ratio should be set to "Auto". Further note that with CPU Core Ratio set to "Sync All Cores", one might have to set the AVX Instruction Core Ratio Negative Offset to "3" in case of system freezes or system instabilities.
 
VT-d Note: For compatibility with VM or parallels, VT-d can be also ENABLED... Verify however, in this case that in your config.plist the boot flag "dart=0" is checked under Arguments in the "Boot" Section of Clover Configurator! 
 
Above 4G Decoding Note: Enable BIOS function "Above 4G Decoding" to avoid memory relocation errors when using AptioMemoryFix.efi on X99 systems.
 
CPU SVID Support: In addition to the BIOS settings mentioned above one should also Enable CPU SVID support in BIOS Section AI Tweaker, which is fundamental for the proper Intel Power Gadget (IPG) CPU power consumption display. 
 
 
C.) Important General Note/Advice and Error Prevention 

 

Please note the following important General Note / Advice and Error Prevention, when setting up your X99 System by implementing the latest macOS Mojave distribution.

 

1.) The /EFI/Clover/drivers64UEFI/-directory of my actual respective X99 EFI-Folder distribution contains by default AptioMemoryFix.efi thanks to @vit9696. Note that with Clover_v2.4k_r4392, AptioMemoryFix.efi has become an official Customization Option of Clover and can now be selected and therefore also just easily implemented in the frame of the Clover Boot Loader Installation.

 

For native NVRAM implementation, Clover's RC Scripts have to be omitted during the clover boot loader installation. If already previously installed, remove Clover's RC Scripts from the /etc directory of your macOS USB Flash Drive Installer or System Disk:

sudo rm -rf /etc/rc.boot.d
sudo rm -rf /etc/rc.shutdown.d

 

Also the "slide" boot flag needs to be disabled.

 

2.a) Most ATI GPUs, e.g. RX Vega 64, RX Vega Frontier, RX 580, RX 560 are supposed to be "natively" implemented. It is commonly recommended not to use RX 560 and RX 580 GPUs due to the lacking iGPU implementation when using SMBIOS iMacPro1,1.
 
With macOS 10.14.5 Beta 1, also the new Radeon VII is now natively implemented.  

By means of my RadeonVII/Vega64/Vega56/RX560/RX580 SSDTs, available in my respective X99 SSDT Github repository, and Whatevergreen.kext, all available DP and HDMI ports, including multi-monitor support, display HotPlug and system sleep/wake should be automatically and successfully implemented. Whatevergreen.kext only seems required for all Vegas possessing less than 6 physical ports (including the original Vegas like Frontier and Vega 64), else the current AMD SSDTs do pretty well their job.
 
Important additional comment for all Vega users with 4K monitors though: when connecting a Vega with e.g. the LG 38UC99-W (WUHD, 3840 pix x 1600 pix) via one of the Display Ports (DPs), the screen resolution is fine under both Windows 10 and macOS High Sierra but is totally at odd during boot (VGA like boot screen resolution). The VEGA DP 4K boot screen resolution issue is neither related with the fact that the LG 38UC99-W is an ultra-wide (3840x1600) and not a true UHD (3840x2160) monitor nor related to any likely apparent issue with the ASUS X99-A II firmware. It is definitely a Vega firmware problem in combination with most 4K displays, as the DP 4K boot screen resolution issue is totally absent with any Nvidia GPU and the problem also does not only affect the ASUS Splash Screen but also spreads over the entire boot process until the login screen is reached (Windows and macOS). Splash Screen, Apple logo or verbose boot messages are not stretched but rather have VGA like resolution. Any fix of the AMD vBIOS would be highly appreciated. It is more than disappointing to witness such issues with 600-1000$ GPUs... Fortunately, the 4K boot screen issue is restricted to the Vega DP ports and likely due to the fact that the LG 38UC99-W only supports DP 1.2. Solution: Connect your Vega and your 4K display via the HDMI port. The 30 Hz HDMI monitor frequency issue under 10.13 is successfully removed under Mojave: monitor frequency of 60 Hz with the display connected via HDMI (in contrary to 75 Hz via DP).
 
b.) Also Nvidia Kepler Graphics Cards are natively implemented.
 
c.) All Users with Nvidia Maxwell and Pascal Graphics Cards Users still have to wait for the official release of 10.14 Web Drivers. I was actively requesting Web Driver development for macOS 10.14 Betas from Nvidia, which has been rejected. I really hope that Nvidia will not leave again the respective community without Web Driver support. In the meanwhile, Nvidia GPU users have to live with e.g. patched Web Driver xxx.40.105 for macOS High Sierra 10.13.6 after a simple patching procedure detailed in Section E.2), although the latter Web Driver is not really suited for 10.14 and works without hardware acceleration. 

 

3.) The /EFI/Clover/drivers64UEFI/-directory of all former EFI-Folder distributions contained a patched version of the actual apfs.efi. The actual apfs.efi can be obtained by following the respective guideline detailed below:

 

Right-click with your mouse on the "Install macOS High Sierra.app" and select "Show Package Contents" -> click with the mouse on "Contents" and subsequently on "Shared Support" -> double-click with the mouse on "BaseSystem.dmg" for mounting.
 
Go to "usr" -> "standalone" -> "i386". Drop the apfs.efi to your Desktop.
 
To patch the apfs.efi for non-verbose boot, follow THIS LINK. Credits to @PMheart and @ermac.
 
Note however, that the entire apsf.efi approach detailed above recently has become totally obsolete. Thanks to the ApfsSupportPkg developed by @acidenthera & Co. and thanks to it's recent implementation to Clover (thanks to @Slice, @Philip Petev & Co.) in form of ApsfDriverLoader.efi, there is no further need of the former apsf.efi in the /EFI/Clover/drivers64UEFI/ directory.  
 
1705330857_Screenshot2018-06-16at20_13_18.png.9a9a38baf5d38941f11df5d6b6acbb2e.png
 
The actual Clover distribution package including the ApsfDriverLoader.efi can by build by means of the Build_Clover.command available on Gitub. Since Version 4.8.8, the latter script also can be used with 10.14 and Xcode 10 + Xcode 10 Command Line Tools thanks to @vector sigma. By adding 
export PATH="/usr/local/bin:/usr/bin:/bin:/usr/sbin:/sbin" && buildclover
to the script,
 
65202932_Screenshot2018-06-16at19_22_20.thumb.png.4507da34fece29ec90d32d225f51fdc2.png
 
the latter also can be used in case of Brew, QT5, UEFITool or MacPorts implementations like Latex, X11, gcc, etc. not yet fully compatible with 10.14 Mojave. Again thanks to @vector sigma for also providing/enabling this trick/possibility . 
 
4.) To avoid CPU thread TSC desynchronisation errors during boot and wake from S3, likely induced by yet erroneous CPU BIOS microcode implementations, we need to use TSCAdjustReset.kext provided by @interferenc in the /EFI/CLOVER/kexts/Other/ directory of both USB Flash Drive and System Disk in the latter case.
 
To access TSCAdjustRest.kext, download primarily its source distribution from Github with the following terminal command:
git clone https://github.com/interferenc/TSCAdjustReset

Subsequently copy the TSCAdjustRest source distribution to your Desktop using the following terminal command:

mv /TSCAdjustReset ~/Desktop

Now change in the terminal to the TSCAdjustReset source distribution on your Desktop with the following terminal command:

cd ~/Desktop/TSCAdjustReset/

Now compile the source distribution with Xcode by using the following terminal command:

xcodebuild

After successful compilation, you will find the TSCAdjustRest.kext in ~/Desktop/TSCAdjustReset/build/Release/

 
Please note that the TSCAdjustRest.kext by default is configured for a 8-core CPU (16 threads) like the i7-7900K. To adopt the kext for Broadwell-E and Haswell-E processors with more or less cores than 8 cores, apply the following approach:
 
a.) Right-click with the mouse on the TSCAdjustRest.kext file and select "Show Packet Contents".
 
b.) Double-click with the mouse on /contents/ . After a right-click on the "Info.plist" file, select "Open with /Other". Select the TextEdit.app and edit the "Info.plist" file.
 
c.) Use the "find"-function of TextEdit.app and search for the term "IOCPUNumber"
 
d.) Note that the adequate IOCPUNumber for your particular CPU is the number of its threads -1, by always keeping in mind that the number of it's threads is always 2x the number of it's cores.
 
Thus, in case of the 10 core i7-6950X, the IOCPUNumber is 19 (20 threads - 1).
<key>IOCPUNumber</key>				<integer>19</integer>
 
and following the same methodology, the correct IOCPUNumber for the 6-core i7-6800K is 11 (12 threads -1)
<key>IOCPUNumber</key>				<integer>11</integer>
 
e.) After adopting the IOCPUNumber for your particular Broadwell-E/EP, Haswell-E/EP processor, save the info.plist file and copy the
modified VoodooTSCSync.kext to the /EFI/CLOVER/kexts/Other/ - directories of both USB Flash Drive Installer and System Disk!

 

5.) Like under macOS 10.13 High Sierra also with macOS 10.14 Mojave, Apple forces all users to use the new Apple file system APFS in case of a Clean Install.  
 
In case that you want to remain with the HFS+ file system, use @Brumbear's Unsolid.kext in the /EFI/Clover/kexts/Other/ directory.
 
Note that there is no way to convert an APFS disk back to HFS+ without the loss of all data, but one can easily reformat an APFS formatted disk to HFS+ under OSX by using either Apple's Disk Utility App or "diskutil" commands. All you need to do is to previously unmount the APFS volume before erasing it with a journaled HFS+ file system and a GRUB Partition Table (GTP). If you want to maintain the disk's content, perform a backup before erasing the disk with a HFS+ format.
 
The application of Apple's Disk utility is straight forward. The  "diskutil" equivalent is detailed below:
 
In the Terminal app, type:
diskutil list

In the output which you can read by scrolling back, you will find all internal disks named /dev/disk0, /dev/disk1, depending upon how many physical disks are present in your system.

 
Make a note of the disk identifier for the disk you intend to format (you can eliminate risk by removing all disks but the intended target).
 
In the Terminal app, type:
diskutil unmount /dev/diskX

where diskX is a place holder for the disk to be unmounted.

 
Now delete the APFS container of diskX:
diskutil apfs deleteContainer /dev/diskX

Subsequently, you can erase the entire disk with HFS+ and a GPT by typing the following terminal command:

diskutil partitionDisk /dev/diskX 1 GPT jhfs+ "iMacPro" R

where /dev/diskX is again a place holder for disk to be erased and iMacPro would be the label for the single partition created. The remaining 1 GPT jhfs+ and R arguments tell diskutil to create a single partition, within a GUID partition table, formatted as Journaled HFS+ and using the entire disk, respectively.

 
Alternatively one can also use the following terminal command:
diskutil partitionDisk /dev/diskX GPT JHFS+ iMacPro 0b

where /dev/diskX is again a place holder for disk to be erased and iMacPro is again the label for the disk partition created. The GPT HFFS+ and 0b arguments again tell diskutil to create a single partition, within a GUID partition table, formatted as Journaled HFS+ and covering the entire disk, respectively.

 
In the Terminal app, type now:
diskutil mount /dev/diskX

where diskX is again a place holder for the disk to be remounted.

 
Note, that by means of the "diskutil approach", brand new unformatted or not compatibly formatted system NVMe, SSD and HDD system drives can be also directly formatted within the macOS Clean Install procedure. When presented with the initial install screen where you are presented options to Restore From Backup or Install, select Terminal from the Utilities menu bar item;
 
The "diskutil" terminal approach is also able to convert a HFS+ macOS Mojave System Disk to APFS. To do so enter the following terminal command:
diskutil apfs convert /dev/diskX

where diskX is again a place holder for the HFS+ disk to be converted to APFS. The same procedure again can also be directly performed by means of Apple's Disk Utility.

 
Important recommendation: If you opt for an APFS System Disk implementation, try to also implement all other disks of your system with APFS file format. On systems with APFS disks and non-APFS disks, the boot duration will increase, as apsf.efi will perform a fsck check of non-AFPS disks (like HFS+ or Fat32) during boot. However, dual boot APFS Systems with an NTFS Windows System Disk are not effected by the apsf.efi issue, as OSX does not know how to properly deal with NTFS.

 

6.) In order to successfully boot your X99 macOS 10.14 Mojave System system, carefully verify that your config.plist contains in Section "KextsToPatch" of Section "Kernel and Kext Patches" of Clover Configurator the 10.14 IOPCIFamily Kext Patch kindly provided by @PMHeart.    
 
kext-patches.thumb.png.f82b76c0a0a49bc591db2f7fff8093db.png
 
 
D.) iMac macOS 10.14 Mojave System Setup
 
Below, one finds a detailed description for the Installation/Update of/to macOS Mojave 10.14. This also includes the EFI-Folder Preparation (D.1), the macOS Mojave 10.14 Installer Package creation (D.2), the macOS Mojave 10.14 USB Flash Drive Installer Creation (D.3) and the macOS Mojave 10.14 Clean Install. One also finds instructions for a direct iMac Pro conversion of a functional Broadwell-E/EP, Haswell-E/EP X99 system with a SMBIOS System Definition different from iMacPro1,1 and standard macOS build implementation (D.5) of any former macOS distribution. D.6 finally provides details to the future iMac Pro macOS Mojave Update Procedure.
 
D.1) iMac Pro EFI-Folder Preparation 
 
In order to successfully boot a macOS USB Flash Drive Installer or System Disk on a Hackintosh system, both drives must be equipped with an EFI-Folder in their EFI partitions. In this Section we will prepare a fully equipped EFI-Folder with SMBIOS iMacPro1,1 System definition.
 
1.) Download and unzip my actual respective X99 EFI-Folder distribution and copy the therein contained EFI-Folder to your Desktop.
 
2.) Open the config.plist in /EFI/Clover/ with the latest version of Clover Configurator (>/= v.4.60.0), proceed to the "SMBIOS" Section and complete the SMBIOS iMacPro1,1 Serial Number, Board Serial Number and SMUUID entries. These details are mandatory to successfully run iMessage and FaceTime on your iMac Pro System. Note that all other iMacPro1,1 SMBIOS Details  are already implemented in the config.plist of my actual respective X99 EFI-Folder distribution.
 
Press several times the "Generate New" Button next to the serial number text field to generate a serial number and board serial number.

With SMBIOS of an iMacPro1,1 it is not currently possible to verify the validity of the serial number on everymac.com.
Therefore, verify the validity of your serial number on appleserialnumberinfo.com instead.
 
Open the https://checkcoverage.apple.com site, paste your Serial Number and confirm that the serial number is not in use yet.

Finally press several times the "Generate New" button next to SmUUID.
 
Depending on your system configuration (Broadwell-E/EP or Haswell-E/EP) change or adopt the following settings if necessary
 
xcpm.thumb.png.a0f0a7df41d5186f6550cafcb20dab2f.png
 
a.) Users of mainboards with locked MSR Register (disabled MSR OSX Kernel write access) have to add the xcpm_core_scope_msrs © Pike R. Alpha Kernel patch in their config.plist under "KernelToPatch" in Section "Kernel and Kext Patches" of Clover Configurator
 
xcpm_core_scope_msrs © Pike R. Alpha 10.14 (kindly provided by @PMHeart)
 
Find: 31 d2 e8 91 fc ff ff
Replace: 31 d2 90 90 90 90 90

and also to check "KernelPm".

 

b.) "FakeCPUID" in "Kernel and Kext Patches" Section of Clover Configurator:
 
Broadwell-E/EP FakeCPUID: "0x040674" 
 
Haswell-E/EP standard FakeCPUID: "0x0306F2"  
 

c.) All Broadwell-E/EP and Haswell-E/EP users have to enable the macOS independent _xcpm performance kernel patch for 10.13.6+ and all 10.14 version  (kindly provided by @PMheart and based on the method developed by @vit9696) in their config.plist under "KernelToPatch" in Section "Kernel and Kext Patches" of Clover Configurator to enable the OC capability of their respective CPUs. 

 

macOS independent _xcpm performance kernel patch for 10.13.6+ and all 10.14 version  (kindly provided by @PMheart and based on the method developed by @vit9696)

Find:    C1E30848 63D389D0 48C1EA20
Replace: C1E308B8 00FF0000 31D29090
 
To successfully boot my Broadwell-E X99 System and to obtain full XCPM-performance I also need to include the following Kernel patch:
 
d.) xcpm_pkg_scope_msrs © Pike R. Alpha (kindly provided by @PMHeart)
Find: BE070000 0031D2E8 91FCFFFF													
Replace: BE070000 0031D290 90909090
 
Further one might want to include:
 
e.) _xcpm_SMT_scope_msrs 1 & 2 © Pike R. Alpha 10.14 (kindly provided by @PMHeart)
Find: BE0B0000 0031D2E8 66FCFFFF																
Replace: BE0B0000 0031D290 90909090
 
Find: 31D2E87E FCFFFF             
Replace: 31D29090 909090

 

f.) Enable "PluginType" in your config.plist under SSDT/Generate Options/ in Section ACPI of Clover Configurator for a fully working XCPM implementation. Note that by this, Pike Alpha's former ssdt.aml XCPM implementation becomes totally obsolete.
 
PluginType.thumb.png.5ac0e4f59fc0d37c333efdcf04369c7d.png
 
g.) Aslo verify once more that your config.plist contains the 10.14 IOPCIFamily kext patch!  
 
Name*             Find*[HEX]          Replace*[HEX]       Comment
IOPCIFamily       483D0000 0040       483D0000 0080       IOPCIFamily patch © PMHeart

h.) Enable USB port limit patches:

 

Valid USB port limit patches for 10.14.4 provided by @PMHeart (hardwired but yet disabled in my respective EFI-Folder distribution) by following initial USB port limit patch approach for 10.14.3 by @ydeng :
 
kext     : com.apple.iokit.IOUSBHostFamily
Find     : 83FB0F0F 87
Replace  : 83FB3F0F 87
Name     : USB Port Limit Patch 1 ©PMHeart
kext     : com.apple.driver.usb.AppleUSBXHCI
Find     : 4183FF0F 0F83
Replace  : 4183FF3F 0F83
Name     : USB Port Limit Patch 2 ©PMHeart
kext     : com.apple.iokit.IOUSBHostFamily
Find     : 83E30FD3 E34109DF
Replace  : 83E33FD3 E34109DF
Name     : USB Port Limit Patch 3 ©PMHeart

 

i.) config.plist "Type" entry in Section "CPU" of Clover Configurator:

 

By default, "0x0F01" for XEON-W is implemented for  Cpu "Type" in the config.plist of the default EFI-Folder configuration, in compliance with SMBIOS iMacPro1,1. While "0x0F01" is fully valid for Syklake-X on X299 platforms, one should better use the correct "Type" entries for the different Broadwell and Haswell CPUs tabled below and kindly provided by @PMHeart:

 

Haswell-E:
⁃ Core i7 Extreme (5960X, 5930K, 5820K): 0x0705
⁃ Xeon E7: 0x0501

Haswell-EP:
⁃Xeon E5: 0x0A01

Broadwell-E:
Core i7 (6950X, 6900K, 6850K, 6800K): 0x0706

Broadwell-EP:
⁃ Xeon E5: 0x0A01

 

Finally save the modified config.plist.

 
3.) Copy the appropriate TSCAdjustRest.kext, which you modified in error prevention C.4), to the /EFI/CLOVER/kexts/Other/ directory of the EFI-Folder.
 
You know have a fully equipped EFI-Folder for subsequent implementations as detailed below.
 
D.2) iMac Pro macOS Mojave 10.14 Installer Package Creation 
 
If you are not able to successfully download the macOS Mojave 10.14.4 (18E226) full package installer (6.04 GB) from the Appstore, follow the individual steps detailed below:

1.) Open a terminal and create a "041-56507" directory on your Desktop. Subsequently change to the newly created directory. All this can be done with the following terminal commands:
 
mkdir ~/Desktop/041-56507/
cd ~/Desktop/041-56507/

 

2.) Download the following files from the Apple server (public links) to your ~/Desktop/041-56507/ directory by a copy & paste of the following terminal commands:

curl https://swdist.apple.com/content/downloads/32/45/041-56507/k6okp4vkzucqpoxrgrgycji6jo8z8na8sg/041-56507.English.dist -o 041-56507.English.dist
curl http://swcdn.apple.com/content/downloads/32/45/041-56507/k6okp4vkzucqpoxrgrgycji6jo8z8na8sg/InstallAssistantAuto.smd -o InstallAssistantAuto.smd
curl http://swcdn.apple.com/content/downloads/32/45/041-56507/k6okp4vkzucqpoxrgrgycji6jo8z8na8sg/AppleDiagnostics.chunklist -o AppleDiagnostics.chunklist
curl http://swcdn.apple.com/content/downloads/32/45/041-56507/k6okp4vkzucqpoxrgrgycji6jo8z8na8sg/AppleDiagnostics.dmg -o AppleDiagnostics.dmg
curl http://swcdn.apple.com/content/downloads/32/45/041-56507/k6okp4vkzucqpoxrgrgycji6jo8z8na8sg/OSInstall.mpkg -o OSInstall.mpkg
curl http://swcdn.apple.com/content/downloads/32/45/041-56507/k6okp4vkzucqpoxrgrgycji6jo8z8na8sg/BaseSystem.chunklist -o BaseSystem.chunklist
curl http://swcdn.apple.com/content/downloads/32/45/041-56507/k6okp4vkzucqpoxrgrgycji6jo8z8na8sg/InstallESDDmg.chunklist  -o InstallESDDmg.chunklist
curl http://swcdn.apple.com/content/downloads/32/45/041-56507/k6okp4vkzucqpoxrgrgycji6jo8z8na8sg/BaseSystem.dmg -o BaseSystem.dmg
curl https://swdist.apple.com/content/downloads/32/45/041-56507/k6okp4vkzucqpoxrgrgycji6jo8z8na8sg/RecoveryHDMetaDmg.pkm -o RecoveryHDMetaDmg.pkm
curl http://swcdn.apple.com/content/downloads/32/45/041-56507/k6okp4vkzucqpoxrgrgycji6jo8z8na8sg/RecoveryHDMetaDmg.pkg -o RecoveryHDMetaDmg.pkg
curl https://swdist.apple.com/content/downloads/32/45/041-56507/k6okp4vkzucqpoxrgrgycji6jo8z8na8sg/InstallAssistantAuto.pkm -o InstallAssistantAuto.pkm
curl http://swcdn.apple.com/content/downloads/32/45/041-56507/k6okp4vkzucqpoxrgrgycji6jo8z8na8sg/InstallAssistantAuto.pkg -o InstallAssistantAuto.pkg
curl http://swcdn.apple.com/content/downloads/32/45/041-56507/k6okp4vkzucqpoxrgrgycji6jo8z8na8sg/InstallInfo.plist -o InstallInfo.plist
curl https://swdist.apple.com/content/downloads/32/45/041-56507/k6okp4vkzucqpoxrgrgycji6jo8z8na8sg/MajorOSInfo.pkm -o MajorOSInfo.pkm
curl http://swcdn.apple.com/content/downloads/32/45/041-56507/k6okp4vkzucqpoxrgrgycji6jo8z8na8sg/MajorOSInfo.pkg -o MajorOSInfo.pkg
curl https://swdist.apple.com/content/downloads/32/45/041-56507/k6okp4vkzucqpoxrgrgycji6jo8z8na8sg/InstallESDDmg.pkm -o InstallESDDmg.pkm
curl http://swcdn.apple.com/content/downloads/32/45/041-56507/k6okp4vkzucqpoxrgrgycji6jo8z8na8sg/InstallESDDmg.pkg -o InstallESDDmg.pkg

 

The full list of package files can be found within the following catalog URL, searching for key "k6okp4vkzucqpoxrgrgycji6jo8z8na8sg":

 

https://swscan.apple.com/content/ca...ion-snowleopard-leopard.merged-1.sucatalog.gz

 

3.) Create the installer.pkg on your Desktop with the following terminal command:
 

cd ..
productbuild --distribution ./041-56507/041-56507.English.dist --package-path ./041-56507/ installer.pkg

 

4.) Create the "Install MacOS Mojave" in the /Applications folder of your System Disk with the following terminal command:

 

sudo /usr/sbin/installer -pkg installer.pkg -target /

 

In case that you receive an error message, ignore the latter and proceed with 5.)

5.) Now add the following files to your "Install macOS Mojave.app" with the following terminal commands:

 

sudo cp ./041-56507/InstallESDDmg.pkg /Applications/Install\ macOS\ Mojave.app/Contents/SharedSupport/InstallESD.dmg
sudo cp ./041-56507/AppleDiagnostics.dmg /Applications/Install\ macOS\ Mojave.app/Contents/SharedSupport/
sudo cp ./041-56507/AppleDiagnostics.chunklist /Applications/Install\ macOS\ Mojave.app/Contents/SharedSupport/
sudo cp ./041-56507/BaseSystem.dmg /Applications/Install\ macOS\ Mojave.app/Contents/SharedSupport/
sudo cp ./041-56507/BaseSystem.chunklist /Applications/Install\ macOS\ Mojave.app/Contents/SharedSupport/

 

Verify your "Install Mojave.app" for completeness. You should now have a complete macOS Mojave 10.14. (18E226) Installer package in your /Applications Folder.

The entire "Install macOS Mojave.app" creation procedure has been also fully automatised within one single script, as already implemented for macOS High Sierra with the help off @macandrea. 

createInstaller-10.14.4-23042019.sh will automatically create on any MacOS System the "Install macOS Mojave.app" for macOS Mojave 10.14.4 (18E226) in the /Applications folder.

Just download und unzip createInstaller-10.14.4-23042019.sh.zip and run the following terminal commands:

 

cd ~/Downloads
chmod +x createInstaller-10.14.4-23042019.sh
./createInstaller-10.14.4-23042019.sh

 

And here is createInstaller-10.14.4-SB-23042019.shwhich will automatically create on any MacOS System the "Install macOS Mojave.app" for macOS Mojave 10.14.4 (18E2034) - special build in the /Applications folder.

 

Just download und unzip createInstaller-10.14.4-SB-23042019.sh.zip and run the following terminal commands:

 

	

	cd ~/Downloads	

	chmod +x createInstaller-10.14.4-SB-23042019.sh	

	./createInstaller-10.14.4-SB-23042019.sh	

 

D.3) iMac Pro macOS Mojave 10.14 USB Flash Drive Installer Creation 
 
Follow the individual steps detailed below to successfully create a bootable iMac Pro macOS Mojave 10.14 USB Flash Drive Installer.
 
1.) Format a USB Flash Drive of your choice (source, named USB) with HFS+ [(Mac OS Extended (Journaled)] and a GUID partition table by means of Apple's Disk Utility on any other Hackintosh or Mac of your choice. This will create an empty HFS+ Partition and a yet empty EFI-partition on your iMac Pro macOS USB Flash Drive Installer.
 
2.) With the macOS Mojave 10.14 Installer Package in your /Application Folder,  connect your USB Flash Drive (named USB) and run the following terminal command:
sudo /Applications/Install\ macOS\ Mojave.app/Contents/Resources/createinstallmedia --volume /Volumes/USB --nointeraction

Alternatively, one can create the iMac Pro macOS USB Flash Drive Installer also by means of the Install Disk Creator.app.

 
3.) For successfully booting your iMac Pro macOS USB Flash Drive Installer, the latter must however also contain a valid EFI- Folder with an SMBIOS iMacPro1,1 system definition. Thus, copy the EFI-Folder you prepared in Section D.1) to the yet empty EFI Partition of your macOS USB Flash Drive Installer.
 
You now have a fully functional and bootable macOS Mojave 10.14 USB Flash Drive Installer.
 
 
D.4) iMac Pro macOS Mojave 10.14 Clean Install on Broadwell-E/EP, Haswell-E/EP, X99
 
Follow the individual steps detailed below to successfully setup macOS Mojave 10.14 on a virgin system drive of your choice (NVMe, SSD or HDD).
 
1.) In order to perform a clean install of macOS Mojave 10.14, prepare a virgin NVMe, SDD or HDD destination drive for the iMac Pro macOS installation by formatting the drive with HFS+ [(Mac OS Extended (Journaled)] and a GUID partition table by means of Apple's Disk Utility on any other Hackintosh or Mac of your choice. This will create an empty HFS+ Partition and a yet empty EFI-partition on the drive.
 
2.) Copy the EFI-Folder you prepared in Section D.1) to the yet empty EFI Partition.
 
3.) Now connect the Destination Drive to your Hackintosh System and boot the latter with the plugged macOS Mojave 10.14 USB Flash Drive Installer, your created in Section D.2)
 
4.) While booting your system, press the F8 button to enter the BIOS boot menu. Select to boot from your macOS USB Flash Drive Installer.
 
5.) Subsequently, click on the USB Flash Drive Installer Icon in the clover boot menu to boot the respective macOS Installer partition on your macOS USB Flash Drive Installer
 
6.) After successful boot, pass the individual steps of the macOS 10.14 Mojave installation menu and finally select the destination drive of your macOS 10.14 Mojave  Installation, which should be logically the system disk you successfully configured above. In the next step, the Installer will create a macOS Mojave 10.14 Installer Partition on the system disk and subsequently reboot your system.
 
7.) During system reboot, just press again the F8 button to enter the BIOS boot menu. Select again to boot from your USB Flash Drive. In contrary to 6.), click this time on the "Install MacOS.." Icon in the clover boot screen to boot the newly created macOS Mojave 10.14 Installer Partition on your system disk.
 
8.) After successful boot, you will enter now the macOS Mojave 10.14 Installer Screen with a progress bar starting at about 34 minutes.
 
9.) After another reboot, press again the F8 button to enter the BIOS boot menu. Select to boot with your System Disk EFI-folder. Click on the "MacOS Mojave" icon on the clover boot screen to boot the new macOS Mojave  partition of your system disk.
 
10.) After successful boot you have to perform the iCloud registration to have your first iMac Pro macOS Mojave 10.14 build. 
 
Proceed with Section D.6) - iMac Pro macOS High Sierra Build Updates (if necessary) or E.) - Post Installation Process.
 
 
D.5) Direct iMac Pro conversions of a functional Broadwell-E/EP, Haswell-E/EP, X99 system with a SMBIOS System Definition different from iMacPro1,1 and a standard macOS build implementation 
 
1.) Replace the EFI-Folder of your System Disk by the EFI-Folder you created in Section D.1)
 
2.) Copy /System/Library/CoreServices/PlatformSupport.plist to your Desktop, add BoardID "Mac-7BA5B2D9E42DDD94" under SupportedBoardIDs by means of Xcode as suggested by user Griven from the German Hackintosh-Forum and copy back the modified PlatformSupport.plist to System/Library/CoreServices/.
 
3.) If not already in your /Applications folder after performing Section D.2), copy the iMac Pro macOS Installer Package to your /Applications folder.
 
4.) Double click on the "Install macOS Mojave.app" in the /Applications Folder to start the macOS Mojave 10.14 installation. 
 
5.) After reboot, click on the "Install MacOS.." Icon in the clover boot screen to boot the newly created macOS Mojave 10.14 Installer Partition on your system disk.
 
6.) After successful boot, you will enter now the macOS Mojave 10.14 Installer Screen with a progress bar starting at 43 minutes.
 
7.) After another reboot, click on the "MacOS Mojave" icon in the clover boot screen to boot the updated macOS Mojave 10.14 on your system disk.
 
8.) After successful boot you have to register at iCloud at the end of the macOS installation, and you will now have your first iMac Pro macOS Mojave 10.14 build.
 
Proceed with Section D.6) - iMac Pro macOS 10.14 Mojave Update Procedure (if necessary) or Section E.) - Post Installation Process.
 
D.6) iMac Pro macOS 10.14 Mojave Update Procedure
 
If you already used my 10.13 iMacPro X99 guide to setup a 10.13 iMac Pro macOS build, you simply have to update your EFI-Folder and directly perform the update to macOS 10.14.0 Mojave from System Disk by else following steps 4.) to 8.) of D.5) above. Any future macOS Mojave update can be directly performed via "Software Update" under "System Preferences".
 

 

E.) Post Installation Process
 
E.1) XNU CPU Power Management (XCPM) Configuration
 
The config.plist of my actual respective X99 EFI-Folder distribution already contains a fully functional XCPM configuration for the i7-6950X Broadwell-E CPU, which just needs to be adopted for other CPU configurations (Broadwell-E/EP different from i7-6950X, Haswell-E/EP).
 
Before adapting the XCPM configuration, verify the following BIOS settings:
 
  • Advanced\CPU Configuration\CPU Power Management Configuration\
  • Enhanced Intel SpeedStep Technology (EIST): Disabled
  • Turbo mode: Enabled
  • CPU C-State: Enabled
  • Enhanced C1 State: Enabled
  • CPU C3 Report: Enabled
  • CPU C6 Report: Enabled
  • Package C State Limit: C6(non Retention) state

 

Subsequently, follow the individual steps below.
 
1.) Open the config.plist of your 10.14 system disk and revise the  "Kernel and Kext Patches" Section.
 
xcpm.thumb.png.a0f0a7df41d5186f6550cafcb20dab2f.png
 
a.) Users of mainboards with locked MSR Register (disabled MSR OSX Kernel write access) have to add the xcpm_core_scope_msrs © Pike R. Alpha Kernel patch in their config.plist under "KernelToPatch" in Section "Kernel and Kext Patches" of Clover Configurator
 
xcpm_core_scope_msrs © Pike R. Alpha 10.14 (kindly provided by @PMHeart)
 
Find: 31 d2 e8 91 fc ff ff
Replace: 31 d2 90 90 90 90 90

and also to check "KernelPm".

 
b.) Verify "FakeCPUID" in "Kernel and Kext Patches" Section of Clover Configurator:
 
Broadwell-E/EP FakeCPUID: "0x040674"    
 
Haswell-E/EP standard FakeCPUID: "0x0306F2" 
 

c.) All Broadwell-E/EP and Haswell-E/EP users have to enable the macOS independent _xcpm performance kernel patch for 10.13.6+ and all 10.14 version  (kindly provided by @PMheart and based on the method developed by @vit9696) in their config.plist under "KernelToPatch" in Section "Kernel and Kext Patches" of Clover Configurator to enable the OC capability of their respective CPUs. 

 

macOS independent _xcpm performance kernel patch for 10.13.6+ and all 10.14 version  (kindly provided by @PMheart and based on the method developed by @vit9696)

Find:    C1E30848 63D389D0 48C1EA20
Replace: C1E308B8 00FF0000 31D29090

 

To successfully boot my Broadwell-E X99 System and to obtain full XCPM-performance I also need to include the following Kernel patch:
 
d.) xcpm_pkg_scope_msrs © Pike R. Alpha (kindly provided by @PMHeart)
Find: BE070000 0031D2E8 91FCFFFF													
Replace: BE070000 0031D290 90909090
Further one also might like to implement:
 
e.) _xcpm_SMT_scope_msrs 1 & 2 © Pike R. Alpha 10.14 (kindly provided by @PMHeart)
Find: BE0B0000 0031D2E8 66FCFFFF																
Replace: BE0B0000 0031D290 90909090
Find: 31D2E87E FCFFFF             
Replace: 31D29090 909090

 

f.) Enable "PluginType" in your config.plist under SSDT/Generate Options/ in Section ACPI of Clover Configurator for a fully working XCPM implementation. Note that by this, Pike Alpha's former ssdt.aml XCPM implementation becomes totally obsolete.
 
g.) Also verify once more in concordance with Error Protection C.6) that the 10.14 IOPCIFamily kext patch is enabled in your config.plist!
Name*             Find*[HEX]          Replace*[HEX]       Comment
IOPCIFamily       483D0000 0040       483D0000 0080       IOPCIFamily patch © PMHeart

There is also no need for injecting any additional frequency vector.

h.) config.plist "Type" entry in Section "CPU" of Clover Configurator:

By default, "0x0F01" for XEON-W is implemented for Cpu "Type" in the config.plist of the default EFI-Folder configuration, in compliance with SMBIOS iMacPro1,1. While "0x0F01" is fully valid for Syklake-X on X299 platforms, one should better use the correct "Type" entries for the different Broadwell and Haswell CPUs tabled below and kindly provided by @PMHeart:

Haswell-E:
⁃ Core i7 Extreme (5960X, 5930K, 5820K): 0x0705
⁃ Xeon E7: 0x0501

Haswell-EP:
⁃Xeon E5: 0x0A01

Broadwell-E:
Core i7 (6950X, 6900K, 6850K, 6800K): 0x0706

Broadwell-EP:
⁃ Xeon E5: 0x0A01

 

2.) Reboot after applying any changes.
 
To verify your XCPM configuration, perform the following steps:
 
1.) Verify with the terminal command "sysctl machdep.xcpm.mode" if the XCPM mode is active. If so, "sysctl machdep.xcpm.mode" should return "1".
 
2.) Verify that in the IORegistryExplorer you have the following entry under CP00@0:
Property:         Type:         Value:
plugin-type       Number        0x1

 

3.) Verify with the terminal command
kextstat|grep -y x86plat

 

that the "X86PlatformPlugin.kext" is loaded. If the command returns something like
112    1 0xffffff7f822bc000 0x17000    0x17000    com.apple.driver.X86PlatformPlugin (1.0.0) FD88AF70-3E2C-3935-99E4-C48669EC274B <111 19 18 13 11 7 6 5 4 3 1>
146    1 0xffffff7f822d3000 0x7000     0x7000     com.apple.driver.X86PlatformShim (1.0.0) DCEA94A4-3547-3129-A888-E9D5C77B275E <112 111 13 7 4 3>

you are fine.

 
4.) Verify with the terminal command
[code]kextstat|grep -y appleintelcpu[/code]

that you got rid of the Apple Intel CPU power management. If the result is empty you are fine.

 
5.) To verify that the Frequency-Vectors are loaded, use the following terminal command:
sysctl -n machdep.xcpm.vectors_loaded_count

 

If everything is ok, the command returns "1".
 
6.) To obtain further information on your XCPM Power Management configuration, download Piker Alpha’s AppleIntelInfo.kext from Github. To compile the source code, you need to primarily install Xcode (Appstore) and Xcode Command Line Tools! This guideline might be helpful for the  successfully installation of the latter.
 
Now enter the following terminal commands:
cd ~/Downloads/AppleIntelInfo-master
xcodebuild
cd build/Release
chmod -R 755 AppleIntelInfo.kext
sudo chown -R root:wheel AppleIntelInfo.kext

 

Load the AppleIntelInfo.kext with "kextload" and "cat" the info-results with the following terminal commands:
sudo kextload AppleIntelInfo.kext
sudo cat /tmp/AppleIntelInfo.dat

 

The cat command should reveal something like the following result:
AppleIntelInfo.kext v2.5 Copyright © 2012-2017 Pike R. Alpha. All rights reserved.

Settings:
------------------------------------------
logMSRs..................................: 1
logIGPU..................................: 0
logCStates...............................: 1
logIPGStyle..............................: 1
InitialTSC...............................: 0x11d3a1760ecb2 (10453 MHz)
MWAIT C-States...........................: 8480

Processor Brandstring....................: Intel(R) Core(TM) i7-6950X CPU @ 3.00GHz

Processor Signature..................... : 0x406F1
------------------------------------------
 - Family............................... : 6
 - Stepping............................. : 1
 - Model................................ : 0x4F (79)

Model Specific Registers (MSRs)
------------------------------------------

MSR_CORE_THREAD_COUNT............(0x35)  : 0x0
------------------------------------------
 - Core Count........................... : 10
 - Thread Count......................... : 20

MSR_PLATFORM_INFO................(0xCE)  : 0x20080C3BF3811E00
------------------------------------------
 - Maximum Non-Turbo Ratio.............. : 0x1E (3000 MHz)
 - Ratio Limit for Turbo Mode........... : 1 (programmable)
 - TDP Limit for Turbo Mode............. : 1 (programmable)
 - Low Power Mode Support............... : 1 (LPM supported)
 - Number of ConfigTDP Levels........... : 1 (additional TDP level(s) available)
 - Maximum Efficiency Ratio............. : 12
 - Minimum Operating Ratio.............. : 8

MSR_PMG_CST_CONFIG_CONTROL.......(0xE2)  : 0x1E000005
------------------------------------------
 - I/O MWAIT Redirection Enable......... : 0 (not enabled)
 - CFG Lock............................. : 0 (MSR not locked)
 - C3 State Auto Demotion............... : 1 (enabled)
 - C1 State Auto Demotion............... : 1 (enabled)
 - C3 State Undemotion.................. : 1 (enabled)
 - C1 State Undemotion.................. : 1 (enabled)
 - Package C-State Auto Demotion........ : 0 (disabled/unsupported)
 - Package C-State Undemotion........... : 0 (disabled/unsupported)

MSR_PMG_IO_CAPTURE_BASE..........(0xE4)  : 0x10414
------------------------------------------
 - LVL_2 Base Address................... : 0x414
 - C-state Range........................ : 1 (C-States not included, I/O MWAIT redirection not enabled)

IA32_MPERF.......................(0xE7)  : 0xACF485063
IA32_APERF.......................(0xE8)  : 0xB96AC7BB7
MSR_0x150........................(0x150) : 0x0

MSR_FLEX_RATIO...................(0x194) : 0xE0000
------------------------------------------

MSR_IA32_PERF_STATUS.............(0x198) : 0x204900001E00
------------------------------------------
 - Current Performance State Value...... : 0x1E00 (3000 MHz)

MSR_IA32_PERF_CONTROL............(0x199) : 0x2A00
------------------------------------------
 - Target performance State Value....... : 0x2A00 (4200 MHz)
 - Intel Dynamic Acceleration........... : 0 (IDA engaged)

IA32_CLOCK_MODULATION............(0x19A) : 0x0

IA32_THERM_INTERRUPT.............(0x19B) : 0x0

IA32_THERM_STATUS................(0x19C) : 0x883D0000
------------------------------------------
 - Thermal Status....................... : 0
 - Thermal Log.......................... : 0
 - PROCHOT # or FORCEPR# event.......... : 0
 - PROCHOT # or FORCEPR# log............ : 0
 - Critical Temperature Status.......... : 0
 - Critical Temperature log............. : 0
 - Thermal Threshold #1 Status.......... : 0
 - Thermal Threshold #1 log............. : 0
 - Thermal Threshold #2 Status.......... : 0
 - Thermal Threshold #2 log............. : 0
 - Power Limitation Status.............. : 0
 - Power Limitation log................. : 0
 - Current Limit Status................. : 0
 - Current Limit log.................... : 0
 - Cross Domain Limit Status............ : 0
 - Cross Domain Limit log............... : 0
 - Digital Readout...................... : 61
 - Resolution in Degrees Celsius........ : 1
 - Reading Valid........................ : 1 (valid)

MSR_THERM2_CTL...................(0x19D) : 0x0

IA32_MISC_ENABLES................(0x1A0) : 0x850089
------------------------------------------
 - Fast-Strings......................... : 1 (enabled)
 - FOPCODE compatibility mode Enable.... : 0
 - Automatic Thermal Control Circuit.... : 1 (enabled)
 - Split-lock Disable................... : 0
 - Performance Monitoring............... : 1 (available)
 - Bus Lock On Cache Line Splits Disable : 0
 - Hardware prefetch Disable............ : 0
 - Processor Event Based Sampling....... : 0 (PEBS supported)
 - GV1/2 legacy Enable.................. : 0
 - Enhanced Intel SpeedStep Technology.. : 1 (enabled)
 - MONITOR FSM.......................... : 1 (MONITOR/MWAIT supported)
 - Adjacent sector prefetch Disable..... : 0
 - CFG Lock............................. : 0 (MSR not locked)
 - xTPR Message Disable................. : 1 (disabled)

MSR_TEMPERATURE_TARGET...........(0x1A2) : 0x640A00
------------------------------------------
 - Turbo Attenuation Units.............. : 0
 - Temperature Target................... : 100
 - TCC Activation Offset................ : 0

MSR_MISC_PWR_MGMT................(0x1AA) : 0x402000
------------------------------------------
 - EIST Hardware Coordination........... : 0 (hardware coordination enabled)
 - Energy/Performance Bias support...... : 1
 - Energy/Performance Bias.............. : 0 (disabled/MSR not visible to software)
 - Thermal Interrupt Coordination Enable : 1 (thermal interrupt routed to all cores)

MSR_TURBO_RATIO_LIMIT............(0x1AD) : 0x2A2A2A2A2A2A2A2A
------------------------------------------
 - Maximum Ratio Limit for C01.......... : 2A (4200 MHz)
 - Maximum Ratio Limit for C02.......... : 2A (4200 MHz)
 - Maximum Ratio Limit for C03.......... : 2A (4200 MHz)
 - Maximum Ratio Limit for C04.......... : 2A (4200 MHz)
 - Maximum Ratio Limit for C05.......... : 2A (4200 MHz)
 - Maximum Ratio Limit for C06.......... : 2A (4200 MHz)
 - Maximum Ratio Limit for C07.......... : 2A (4200 MHz)
 - Maximum Ratio Limit for C08.......... : 2A (4200 MHz)

MSR_TURBO_RATIO_LIMIT1...........(0x1AE) : 0x2222222222222A2A
------------------------------------------
 - Maximum Ratio Limit for C09.......... : 2A (4200 MHz)
 - Maximum Ratio Limit for C10.......... : 2A (4200 MHz)

IA32_ENERGY_PERF_BIAS............(0x1B0) : 0x5
------------------------------------------
 - Power Policy Preference...............: 5 (balanced performance and energy saving)

MSR_POWER_CTL....................(0x1FC) : 0x2904005B
------------------------------------------
 - Bi-Directional Processor Hot..........: 1 (enabled)
 - C1E Enable............................: 1 (enabled)

MSR_RAPL_POWER_UNIT..............(0x606) : 0xA0E03
------------------------------------------
 - Power Units.......................... : 3 (1/8 Watt)
 - Energy Status Units.................. : 14 (61 micro-Joules)
 - Time Units .......................... : 10 (976.6 micro-Seconds)

MSR_PKG_POWER_LIMIT..............(0x610) : 0x7FFF80015FFF8
------------------------------------------
 - Package Power Limit #1............... : 4095 Watt
 - Enable Power Limit #1................ : 1 (enabled)
 - Package Clamping Limitation #1....... : 1 (allow going below OS-requested P/T state during Time Window for Power Limit #1)
 - Time Window for Power Limit #1....... : 10 (2560 milli-Seconds)
 - Package Power Limit #2............... : 4095 Watt
 - Enable Power Limit #2................ : 1 (enabled)
 - Package Clamping Limitation #2....... : 1 (allow going below OS-requested P/T state setting Time Window for Power Limit #2)
 - Time Window for Power Limit #2....... : 3 (20 milli-Seconds)
 - Lock................................. : 0 (MSR not locked)

MSR_PKG_ENERGY_STATUS............(0x611) : 0xC06AC
------------------------------------------
 - Total Energy Consumed................ : 48 Joules (Watt = Joules / seconds)

MSR_PKGC3_IRTL...................(0x60a) : 0x0
MSR_PKGC6_IRTL...................(0x60b) : 0x0
MSR_PKG_C2_RESIDENCY.............(0x60d) : 0x298ED1EE0
MSR_PKG_C3_RESIDENCY.............(0x3f8) : 0xD638F0
MSR_PKG_C2_RESIDENCY.............(0x60d) : 0x298ED1EE0
MSR_PKG_C3_RESIDENCY.............(0x3f8) : 0xD638F0
MSR_PKG_C6_RESIDENCY.............(0x3f9) : 0x44911A9AC

IA32_TSC_DEADLINE................(0x6E0) : 0x11D3A1BDB3826

CPU Ratio Info:
------------------------------------------
Base Clock Frequency (BLCK)............. : 100 MHz
Maximum Efficiency Ratio/Frequency.......: 12 (1200 MHz)
Maximum non-Turbo Ratio/Frequency........: 30 (3000 MHz)
Maximum Turbo Ratio/Frequency............: 42 (4200 MHz)
P-State ratio * 100 = Frequency in MHz
------------------------------------------
CPU P-States [ (12) 27 30 ]
CPU C3-Cores [ 1 2 4 6 8 10 12 14 16 18 ]
CPU C6-Cores [ 0 2 4 6 8 10 12 14 16 18 ]
CPU P-States [ 12 17 27 (30) ]
CPU C3-Cores [ 1 2 3 4 6 7 8 10 11 12 14 15 16 18 19 ]
CPU C6-Cores [ 0 2 4 6 8 9 10 12 14 16 17 18 ]
CPU P-States [ (12) 17 27 30 31 ]
CPU C3-Cores [ 0 1 2 3 4 6 7 8 9 10 11 12 14 15 16 18 19 ]
CPU P-States [ (12) 14 17 27 30 31 ]
CPU C3-Cores [ 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 18 19 ]
CPU C6-Cores [ 0 2 4 6 8 9 10 12 14 15 16 17 18 ]
CPU P-States [ (12) 14 17 20 27 30 31 ]
CPU C3-Cores [ 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 ]
CPU C6-Cores [ 0 1 2 4 6 7 8 9 10 12 14 15 16 17 18 ]
CPU P-States [ (12) 14 16 17 20 27 30 31 ]
CPU P-States [ (12) 14 16 17 18 20 27 30 31 ]
CPU P-States [ (12) 14 16 17 18 20 27 30 31 32 ]
CPU P-States [ (12) 14 16 17 18 20 22 27 30 31 32 ]
CPU C6-Cores [ 0 1 2 3 4 6 7 8 9 10 12 14 15 16 17 18 ]
CPU P-States [ (12) 13 14 16 17 18 20 22 27 30 31 32 ]
CPU C6-Cores [ 0 1 2 3 4 6 7 8 9 10 12 13 14 15 16 17 18 19 ]
CPU P-States [ (12) 13 14 16 17 18 20 22 23 27 30 31 32 ]
CPU P-States [ 12 13 14 (15) 16 17 18 20 22 23 27 30 31 32 ]
CPU P-States [ (12) 13 14 15 16 17 18 20 22 23 25 27 30 31 32 ]
CPU P-States [ (12) 13 14 15 16 17 18 20 21 22 23 25 27 30 31 32 ]
CPU C6-Cores [ 0 1 2 3 4 6 7 8 9 10 11 12 13 14 15 16 17 18 19 ]
CPU P-States [ 12 13 14 15 16 17 18 20 21 22 23 (24) 25 27 30 31 32 ]
CPU P-States [ (12) 13 14 15 16 17 18 19 20 21 22 23 24 25 27 30 31 32 ]
CPU P-States [ 12 13 14 15 16 17 18 19 20 21 22 23 24 25 27 29 (30) 31 32 ]
CPU C6-Cores [ 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 ]
CPU P-States [ 12 13 14 15 16 17 18 19 20 21 22 23 24 25 27 28 29 30 31 32 (42) ]
CPU P-States [ 12 13 14 15 16 17 18 19 20 21 22 23 24 25 27 28 29 30 31 32 36 (42) ]
CPU P-States [ 12 13 14 15 16 17 18 19 20 21 22 23 24 25 27 28 29 30 31 32 34 36 (42) ]
CPU P-States [ 12 13 14 15 16 17 18 19 20 21 22 23 24 25 27 28 29 30 31 32 34 35 36 (42) ]
CPU P-States [ 12 13 14 15 16 17 18 19 20 21 22 23 24 25 27 28 29 30 31 32 34 35 36 41 (42) ]
CPU P-States [ 12 13 14 15 16 17 18 19 20 21 22 23 24 25 27 28 29 30 31 32 34 35 36 37 41 (42) ]
CPU P-States [ 12 13 14 15 16 17 18 19 20 21 22 23 24 25 27 28 29 30 31 32 34 35 36 37 38 41 (42) ]
CPU P-States [ 12 13 14 15 16 17 18 19 20 21 22 23 24 25 27 28 29 30 31 32 34 35 36 37 38 39 41 (42) ]
CPU P-States [ (12) 13 14 15 16 17 18 19 20 21 22 23 24 25 27 28 29 30 31 32 34 35 36 37 38 39 40 41 42 ]
CPU P-States [ (12) 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 34 35 36 37 38 39 40 41 42 ]
CPU P-States [ 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 (42) ]

 

To unload the AppleIntelInfo.kext, enter the terminal command:
sudo kextunload AppleIntelInfo.kext

 

E.2) Graphics Configuration

 

Most ATI GPUs, e.g. RX Vega 64, RX Vega Frontier, RX 580, RX 560 are supposed to be "natively" implemented. It is commonly recommended not to use RX 560 and RX 580 GPUs due to the lacking iGPU implementation when using SMBIOS iMacPro1,1.
 
With macOS 10.14.5 Beta 1, also the new Radeon VII is now natively implemented.  

By means of my RadeonVII/Vega64/Vega56/RX560/RX580 SSDTs, available in my respective X99 SSDT Github repository, and Whatevergreen.kext, all available DP and HDMI ports, including multi-monitor support, display HotPlug and system sleep/wake should be automatically and successfully implemented. Whatevergreen.kext only seems required for all Vegas possessing less than 6 physical ports (including the original Vegas like Frontier and Vega 64), else the current AMD SSDTs do pretty well their job.
 
Important additional comment for all Vega users with 4K monitors though: when connecting a Vega with e.g. the LG 38UC99-W (WUHD, 3840 pix x 1600 pix) via one of the Display Ports (DPs), the screen resolution is fine under both Windows 10 and macOS High Sierra but is totally at odd during boot (VGA like boot screen resolution). The VEGA DP 4K boot screen resolution issue is neither related with the fact that the LG 38UC99-W is an ultra-wide (3840x1600) and not a true UHD (3840x2160) monitor nor related to any likely apparent issue with the ASUS X99-A II firmware. It is definitely a Vega firmware problem in combination with most 4K displays, as the DP 4K boot screen resolution issue is totally absent with any Nvidia GPU and the problem also does not only affect the ASUS Splash Screen but also spreads over the entire boot process until the login screen is reached (Windows and macOS). Splash Screen, Apple logo or verbose boot messages are not stretched but rather have VGA like resolution. Any fix of the AMD vBIOS would be highly appreciated. It is more than disappointing to witness such issues with 600-1000$ GPUs... Fortunately, the 4K boot screen issue is restricted to the Vega DP ports and likely due to the fact that the LG 38UC99-W only supports DP 1.2. Solution: Connect your Vega and your 4K display via the HDMI port. The 30 Hz HDMI monitor frequency issue under 10.13 is successfully removed under Mojave: monitor frequency of 60 Hz with the display connected via HDMI (in contrary to 75 Hz via DP).
 
Also Nvidia Kepler Graphics Cards are natively implemented.
 
All Users with Nvidia Maxwell and Pascal Graphics Cards Users still have to wait for the official release of 10.14 Web Drivers. I was actively requesting Web Driver development for macOS 10.14 Public Betas from Nvidia, which has been rejected. I really hope that Nvidia will not leave again the respective community without Web Driver support. In the meanwhile, Nvidia GPU users have to live with e.g. patched Web Driver xxx.40.105 for macOS High Sierra 10.13.6 after a simple patching procedure detailed below, although the latter Web Driver is not really suited for 10.14 and works without hardware acceleration. 

 

How to patch an Nvidia WebDriver:
 
Download the Nvidia WebDriver-Payload Repackager from InsanelyMac. Credits to @Chris111 and @Pavo. 
 
The patch procedure is simple and fully described in the implemented Readme.txt and will reveal a Repackaged-WebDriver.pkg, which can be used for installing the patched Nvidia Web Driver xxx.35.106 under macOS Mojave 10.14.
 
Nvidia Web Driver Installation and Black Screen Prevention:
 
Apparently with SMBIOS iMacPro1,1, the Nvidia Black Screen Prevention has become obsolete. Thanks to @fabiosun for this finding. Thus, NvidiaGraphicsFixup.kext, subverting AppleMobileFileIntegrity banning the driver can be theoretically removed from the /EFI/CLOVER/kexts/Other/ directory of your macOS Flash Drive Installer and 10.13 System Disk. However, actual releases of Whatevergreen.kext and Lilu.kext apparently also help in fixing the Nvidia HDAU implementation and sporadic black screen issues while wake from sleep. Thus, the latter kext combination might still represent potential workarounds for few likely remaining system issues. 
 
a.) Install the patched Nvidia 10.13 Web Driver Package.
 
b.) Now perform the following additional steps:
 
i.) Copy /L/E/NVDAStartupWeb.kext to your Desktop.
 
ii.) Right-click on NVDAStartupWeb.kext and select show package content.
 
iii.) Change to "Contents" and edit the "Info.plist" with Xcode.
 
iv.) Go to IOKitPersonalities -> NVDAStartup -> change "NVDARequiredOS" from "17F77" to "18D42", the corresponding build number of MacOS Mojave 10.14.3.
 
v.) Save the "Info.plist" file and copy the modified "NVDAStartupWeb.kext" to /L/E/ with root permission.
 
vi.) Open a terminal and enter the following commands:
sudo chmod -R 755 /Library/Extensions/NVDAStartupWeb.kext
sudo chown -R root:wheel /Library/Extensions/NVDAStartupWeb.kext
sudo touch /System/Library/Extensions && sudo kextcache -u /
sudo touch /Library/Extensions && sudo kextcache -u /

 

vii.) Reboot.

 
viii.) The patched Web Driver might not be active yet. Therefore, open the Nvidia Driver Manager and select "Nvidia Web Driver".
 
ix.) Now reboot as requested and you will have a fully functional patched Web Driver for MacOS Mojave 10.14.1.

 

 

E.3) Audio Configuration

 

My actual respective X99 EFI-Folder distribution contains an already fully functional AppleALC audio configuration. The latter consist of:

 

1.) Actual versions of codeccommander.kext AppleALC.kext and Lilu.kext in "/EFI/CLOVER/kexts/Other/ 

 

Boot.thumb.png.daf25e090ae9e8e81f0a1b2b1c7b7d68.png 

 

2.)  Note that ALZA -> HDEF ACPI patch needs to be added to the config.plist in Section "ACPI" of Clover Configurator, in case one does not use the adopted system SSDT discussed in Section 9.2).    

Comment:                Find:           Replace:
ALZA -> HDEF            414c5a41        48444546

 

3.) Audio ID Injection "5" in the config.plist under Audio/Inject in Section "Devices" of Clover Configurator. 

 
Devices.thumb.png.0e332473c6d6fb99f0643f166cebf818.png
 
This audio configuration provides a correct analogue onboard audio chipset system implementation. 
 
The correct digital HDMI/DP HDAU PCI device implementation will be detailed in Section E.9) in line with the HDEF and GPU PCI device implementation.
 
Thanks to @nmano for helping me with the initial AppleALC audio setup for 10.14 Mojave. 

 

E.4) USB Configuration 
 
Since 10.13.SU and with AppleIntelPCHPMC, macOS should properly implement all external and internal XHC USB 3.0 (USB 3.1 Gen 1 Type-A) and USB 2.0 (USB 2.0 Gen 1 Type-A) connectors, always provided that one uses working USB port limit patches.
 

Valid USB port limit patch for 10.14.4 provided by @PMHeart (hardwired but yet disabled in my respective EFI-Folder distribution) by following USB port limit patch approach for 10.14.3 by [USER=1614363]@ydeng[/USER]:

 

USB port limit patch for 10.14.4 provided by @PMheart:

kext     : com.apple.iokit.IOUSBHostFamily
Find     : 83FB0F0F 87
Replace  : 83FB3F0F 87
Name     : USB Port Limit Patch 1 ©PMHeart
kext     : com.apple.driver.usb.AppleUSBXHCI
Find     : 4183FF0F 0F83
Replace  : 4183FF3F 0F83
Name     : USB Port Limit Patch 2 ©PMHeart
kext     : com.apple.iokit.IOUSBHostFamily
Find     : 83E30FD3 E34109DF
Replace  : 83E33FD3 E34109DF
Name     : USB Port Limit Patch 3 ©PMHeart

 

Former USB port limit patches for 10.14.3 provided by ©ydeng:

kext     : com.apple.iokit.IOUSBHostFamily
Find     : 83FB0F0F 871604 00
Replace  : 83FB3F0F 871604 00
Name     : USB Port Limit Patch 1 ©ydeng
kext     : com.apple.driver.usb.AppleUSBXHCI
Find     : 83FB0F0F 838F0400 00
Replace  : 83FB3F0F 838F0400 00
Name     : USB Port Limit Patch 2 ©ydeng
kext     : com.apple.iokit.IOUSBHostFamily
Find     : 83E30FD3 E34109DF
Replace  : 83E33FD3 E34109DF
Name     : USB Port Limit Patch 3 ©ydeng

However, it is strongly recommended to use board-specific XHC USB kexts in addition. Such board-specific XHC USB kexts can be easily created for any motherboard of any brand by following my respective XHC USB Kext Creation guideline. Being mainboard specific, a XHC USB kext is only valid for one particular mainboard model although users of the same mainboard model naturally can share the same XHC USB kext, if complete and properly implemented without any additional efforts.
 
KGP-iMacPro-ASUS-X99AII-XHCI.kext would be the XHC USB kext for the ASUS X99-A II with all 20 ports implemented.
 
However, it is strongly recommend to keep respective USB port limit patches disabled and to use a truncated 15-port kext instead, which might avoid buffer overruns and makes your system more vanilla with respect to future macOS updates.
 
For the truncated 15-port kext, we have to drop some of the 20 HS and SS ports implemented from the kext to stay within Apple's 15 USB port limit. For truncating a fully implemented XHC USB kext (all 20 HS and SS ports implemented), I usually recommend to drop one out of usually two internal USB3.0 connectors (which already reduces the number of implemented ports to 16 for the ASUS ASUS X99-A II):
 
1162604037_Screenshot2018-11-05at10_01_25.thumb.png.3cb09d03115eb0c79668fd1f6f17f2cc.png
 
 
To remain within the 15 USB port limit, I also recommend to drop one of the four USB2.0 ports at the backside of the mainboard from the kext (HS05, HS06, HS13 or HS14), which further reduces the number of implemented USB ports by one.
 
2030425144_Screenshot2018-10-31at17_04_34.png.5d7cd5a1909e09855604c6c9eeb47504.png
 
Thus, in total we have now 15 implemented HS and SS ports and we just stay within the 15 USB port limit. In the truncated KGP-iMacPro-ASUS-X99AII-XHCI-15port.kext attached below, I removed HS03, HS04, SSP3, SSP4 (assigned to the internal USB3.0 header USB3_34) and HS05 (assigned to the most right USB2.0 connector in the second column from top on the back panel of the mainboard) from the kext. By this, all other USB2.0 and USB3.0 ASUS-A II onboard connectors remain fully functional. Alternatively, one could also drop e.g. HS01, HS01, SSP1, SSP1 (assigned to the internal USB3.0 header USB3_12) and either HS13, HS14 or HS06 from KGP-iMacPro-ASUS-X99AII-XHCI.kext. Up to your personal taste.
 
All experienced users are kindly invited to provide their fully implemented XHC USB kext and truncated 15-port XHC USB kext for a motherboard not yet being part of the respective XHC USB Kext Library with an implemented port-layout.rtf and by else following the correct kext nomenclatures defined in my XHC USB Kext creation guidelines in line with full motherboard and SMBIOS denominations.
 
Remaining USB ejection issues during sleep/wake likely can be fixed by 3rd party software tools like e.g. mountain.app

 

 

E.5) M.2/NVMe Configuration

 

In contrary to macOS Sierra 10.12, and like already in case of macOS High Sierra 10.13, also macOS 10.14 Mojave provides native support of non-4Kn NVMe SSDs, like my Samsung EVO 960 M.2/NVMe. All patches applied under macOS Sierra 10.12 are obsolete. The native support of non-4Kn NVMe SSDs enables the unique opportunity to directly perform a clean-install of macOS High Sierra 10.13 on M.2 NVMEs like the Samsung EVO 960.
 
The only current drawback consists in the external drive implementation of NVMEs. This minor issue should be easily solved by adding the actual External NVME Icon KextToPatch entry to the config.plist by means of the Clover Configurator.
[code]
Name*            Find* [HEX]           Replace* [HEX]        Comment
IONVMeFamily     4885c074 07808b20     4885c090 90808b20     External NVME Icon Patch[/code]

Not however that within the actual 10.14 Mojave distribution, this approach does not seem to work anymore, despite the KextToPatch entry detailed above. If you still have your NVMe implemented in form of an external drive you have to perform the following workaround, detailed below.

 
1.) Disable the not working External NVME Icon KextToPatch entry.
 
2.) Open the IORegistryExplorer, in the upright search field type nvme and take not of values in the left column, i.e. indicated as v.1, v.2 and v.3 and marked by red rectangles in the figure below. As you can see by following these entries, your nvme device shows up in PCI0@0 > BR1B@1,1 > H000@0
 
NVMe-Patch.thumb.png.7419c27665d147f09e9005f6e68bb436.png
 
3.) Download and unzip the SSDT-NVMe-extern-icon-patch.aml.zip, and open the SSDT-NVMe-extern-icon-patch.aml with MaciASL-DSDT.app, both attached towards the end of this guide. For deviating system configurations, replace the values highlighted in blue color in the figure below with those of your IOReg, marked by red rectangles and indicated by v.1, v.2 and v.3 in the figure of my IOReg above.
 
nvme-patch_aml.thumb.png.934605ac1e4df04401d591d4de66b67b.png
 
4.) Save and copy the modified SSDT-NVMe-extern-icon-patch.aml to the /EFI/CLOVER/ACPI/patched/ folder of your system drive.
 
5.) Reboot
 
Now your NVMe drive should correctly show up as internal.

 

 

E.6) SSDT/NVMe TRIM Support 

 
Macs only enable TRIM for Apple-provided solid-state drives they come with. If you upgrade a Mac with an aftermarket SSD/NVMe, the Mac won’t use TRIM with it. The same applies for SSDs/NVMes used by a Hackintosh. When an operating system uses TRIM with a solid-state drive, it sends a signal to the SSD/NVMe every time you delete a file. The SSD/NVMe knows that the file is deleted and it can erase the file’s data from its flash storage. With flash memory, it’s faster to write to empty memory — to write to full memory, the memory must first be erased and then written to. This causes your SSD/NVMe to slow down over time unless TRIM is enabled. TRIM ensures the physical NAND memory locations containing deleted files are erased before you need to write to them. The SSD/NVMe can then manage its available storage more intelligently.
 
Note that the config.plist of my actual respective X99 EFI-Folder distribution contains an SSD/NVMe "TRIM Enabler" KextsToPatch entry, which can be found in the " Kernel and Kext Patches" Section of the Clover Configurator.
 
Trim.thumb.png.456c6498268abcb97a40536927fc1690.png
 
Name*                   Find*[HEX]                  Replace*[HEX]               Comment
IOAHCIBlockStorage      4150504c 45205353 4400      00000000 00000000 0000      Trim Enabler

 

With this KextToPatch entry, SSD/NVMe TRIM should be  fully enabled also on your 10.14 System. See your Apple's System Report.

 

E.7) GC-Titan Ridge / GC-Alpine Ridge or ASUS TBEX 3 Add-in PCIe Adapter Implementation

 

For the successful implementation of the GC-Titan Ridge (recommended), GC-Alpine Ridge (compatible) or ASUS Thunderbolt EX3 (R.I.P) PCIe Add-In Adapters, a fully working Dual Boot System with an UEFI Windows Implementation is unfortunately absolutely mandatory. You will not be able to configure your Thunderbolt 3 Adapter in the mainboard BIOS, until the Adapter has been successfully recognised and initialised by the UEFI Windows System. Fortunately legal and official License Keys for the actual Windows 10 Pro distribution can be purchased with a little bit of temporal effort on Google for an actual price of 20 $ or even below! Thus, the installation of a dual boot system with Windows will require some additional temporal user effort but will not noticeably further affect the users's budget.
 
Please note that I especially emphasize the term UEFI, when speaking about the parallel Windows implementation. Don't use or perform a Legacy Implementation of Windows! In order to properly implement your Windows partition later-on in the Clover Bootloader and to comply with the actual Mainbaord-BIOS settings requirements, it is absolutely mandatory to run or perform an UEFI Windows implementation!
 
So if not already implemented, how to achieve a fully working UEFI Windows Implementation and Dual boot System with Windows?
 
1.) Important Note! For the implementation of the UEFI Windows Distribution disconnect all usually plugged macOSDrives from your rig! The Windows installer will implement a Windows Boot Loader! If you have any macOS Drive connected during installation, the latter Windows Boot Loader might overwrite and destroy your current Clover Boot Loader. This is the last thing you want! Thus for the windows installation just connect the destination drive for the installation and the Windows USB Flash Drive Installer your will create in the subsequent step below!
 
2.) This Tutorial explains in all necessary detail how to download an actual Windows 10 Creator distribution,  and how tosubsequently create a bootable USB Flash Drive Installer for a subsequent UEFI Windows 10 installation by means RUFUS! Don't put emphasis on alternative optional methods and always take care that you just follow the instructions for a successful subsequent UEFI Windows Installation!
 
3.) This Tutorial explains in all necessary detail how to properly perform the actual Windows 10 Pro Creator UEFIInstallation, subsequent to the a bootable Windows USB Flash Drive Installer realisation detailed in 2.) above.
 
4.) This Tutorial explains in all necessary detail, how to migrate/clone/backup your Windows 10 UEFI System Disk afterinstallation for future maintenance and safety.
 
5.) After successfully performing the UEFI Windows 10 Pro Creator Implementation, you can reconnect your macOS driveto your rig. The newly created UEFI Windows 10 Pro Creator Partition will automatically appear as a further boot option in both BIOS Boot Option Menu (F8) and Clover Boot Menu! No additional or further actions or measurements have to be taken!
 
6.) Once your Windows 10 Pro Creator Partition is fully operational, install all mainboard drivers and programs implemented on the DVD attached to your mainboard. 
 
7.) Now switch off your rig and start with the installation of our Thunderbolt 3 Add-In PCIe Adapter

I recommend to install the Thunderbolt 3 Add-In PCIe Adapter in the 4th PCIe Slot from top, which is PCIEX_3
 
8.) Reboot into windows and install accompanying TB3 PCIe Drivers and Software.

9.) Reboot and enter the Mainboard BIOS (F2)

Go to /Advanced/ Thunderbolt(TM) Configuration/ and apply the following BIOS Settings detailed below:
 
IMG_0451.jpg.57fda26eec65f7b36fac62e6b53fdc4d.jpg
IMG_0452.jpg.eac7940255e1027cb7b3113840f69db9.jpg
 
10.) Shut down your rig, connect the Thunderbolt Device to your Thunderbolt 3 Adaptor and boot your system. 

11.) You are done! Your Thunderbolt 3 Adapter and the connected device should now be fully implemented and functional.

12.) We will add TB XHC USB and TB HotPlug functionality in Section E.9.2) of this guide. Note that with the GC-Titan Ridge, HotPlug functionality can be gained with the THB_C connected. For HotPlug with the other TB adaptors, the THB-C must be removed from most of the available mainboards.
 
E.8) Gigabit and 10-Gbit Ethernet Implementations 
 
Section E.8.1) and and E.8.2.) below, describe in all necessary detail how to gain full Gbit and 10-Gbit LAN functionality on X99 systems.

 

E.8.1) ASUS X99-A onboard Gbit functionality   

 

The Intel I218-V2 Gigabit on-board LAN controller of the ASUS X99-A II is implemented by means of IntelMausiEthernet.kext (already part of my EFI-Folder distributions).

 

E.8.2) 10-Gbit Lan Implementations  

 

E.8.2.1) ASUS XG-C100C Aquantia AQC 10-Gbit NIC   

 

Starting with 10.13.2 there is native support for the Aquantia AQTION AQC107 10-GBit NIC of the iMac Pro in form of vanilla kext "AppleEthernetAquantiaAqtion.kext", which is further part of "IONetworkingFamily.kext/Contents/PlugIns/" placed in /System/Library/Extensions/ (credits to @mikeboss). First success with the ASUS XG-C100C Aquantia AQTION AQC107 10-GBit PCIe x4 NIC under MacOS 10.13.3 has been reported by @d5aqoep. @Mieze finally came up with a AppleEthernetAquantiaAqtion KextPatch for the use of the ASUS XG-C100C Aquantia AQTION AQC107 10-GBit PCIe x4 NIC also under 10.13.4 and and later macOS versions.
 
For further information and discussion see 

How to successfully implement the ASUS XG-C100C Aquantia AQTION AQC107 10-GBit PCIe x4 NIC:
 
1.) A temporal macOS High Sierra 10.13.3 (17D2047 in case of the iMac Pro) installation is absolutely mandatory at first place. Only within the latter macOS High Sierra build, the ASUS XG-C100C Aquantia AQTION AQC107 10-GBit PCIe x4 NIC will receive the proper AQC107 Apple firmware to be recognised and fully implemented by OSX. The firmware update will be performed during system boot. Several boot intents might be necessary until the firmware update finally succeeds. Only subsequently, the ASUS XG-C100C Aquantia AQTION AQC107 10-GBit PCIe x4 NIC will be natively implemented in macOS High Sierra 10.13.3 and fully functional.
 
2.) To finally use the ASUS XG-C100C with macOS builds >10.13.4, one has to implement the built-in AppleEthernetAquantiaAqtion KextPatch provided by [USER=389154]@Mieze[/USER]:
Name*                            Find*[HEX]           Replace*[HEX]      Comment										
AppleEthernetAquantiaAqtion      6275696C 742D696E    62626262 62626262  Aquantia "built-in" patch ©Mieze
 
3.) The proper XGBE ASUS XG-C100C PCI SSDT implementation is detailed in Section E.9.2)
 
4.) Note that after the firmware update under macOS High Sierra 10.13.3, the ASUS XG-C100C Aquantia AQTION AQC107 10-GBit PCIe x4 NIC will refuse the official Windows Lan drivers provided by ASUS and will only work with Apple's customised Aquantia64.zip boot camp drivers attached below.
 
Preferable AQC107 10-Gbit NIC PCIe solutions now available on the market are the Syba 1 Port PCIe x4 10GB  Aquantia AQTION AQC107 NIC (thanks to @mirwaiz for his respective discovery and for all subsequent confirmation of his findings by @mm2margaret , who also pointed me to this extremely valid approach) and the 1 Port PCIe x4 10GB Aquantia AQtion AQC107 10G Gaming NIC (thanks to @izo1 for respective findings and advises), which are natively implemented under macOS OoB and neither need the above firmware update nor the respective AppleEthernetAquantiaAqtion kext patch.
 
E.8.2.2) Intel X540-T1 10-Gbit NIC   
 
Thanks to some Ubuntu EEPROM modding, I also achieved the successful implementation of the Intel X540-T1 single port 10GB LAN PCIe Adapter by means of the Small-Tree 10GB macOS 10.13 driver.
 
Important additional notes to the EEPROM modding guideline linked above can be assessed in Section E.8.2.2) of my iMac Pro Skylake-XX299 macOS 10.14 Mojave Build and Desktop guide.
 
The proper Intel X540-T1 PCI SSDT implementation is detailed in Section E.9.2)
 
E.8.2.3) Small-Tree P2EI0G-2T 10-GBit NIC   

 

The Small-Tree P2EI0G-2T 2-Port 10GB LAN PCIe Adapter constitutes now the actual base line in my iMac Pro X299 10Gbit LAN configuration. It works OoB with the Small-Tree 10GB macOS 10.13 driver.
 
The proper Small-Tree P2EI0G-2T PCI SSDT implementation is detailed in Section E.9.2)
 
E.8.2.4) NetGear ProSave XS508M 8-port 10-Gbit Switch   

 

As already mentioned above, the NetGear ProSave XS508M 8-port 10GBit switch constitutes the turntable of my 10-GBit Ethernet Network. It further connects with a QNAP TS-431X2 Quad-core 4-Bay NAS tower with Built-in 10GbE SFP+ Port.

 

E.8.2.5) QNAP TS-431X2 Quad-core 4-Bay NAS

 

The QNAP TS-431X2 Quad-core 4-Bay NAS tower finally harbours 4x 12 TB Seagate IronWolf drives in RAID 0 configuration (as I rather opt for read/write speed than redundancy).

 

E.8.2.5) 10-Gbit Ethernet Optimization

 

1.) Use SMB 3.0 instead of AFS for your Ethernet communication.
2.) Enable Jumbo Frames on your NAS and macOS network settings.
3.) The service order in your macOS network settings should have your 10-Gbit NIC at first position.
4.) You can turn off the SMB packet signing of the client and server in a secure network.
 
Incoming SMB
 
Enter the following terminal commands:
sudo -s

echo "[default]" >> /etc/nsmb.conf

echo "signing_required=no" >> /etc/nsmb.conf

exit

 

Outgoing SMB:
 
Enter the following terminal commands:
smbutil statshares -a

sudo defaults write /Library/Preferences/SystemConfiguration/com.apple.smb.server SigningRequired 0

 

 

E.9) ASUS X99-A II PCI Device Implementation

 

In order to properly implement all PCI device drivers on his/her system and build, one needs adequate ACPI DSDT Replacements and a sophisticated system SSDTs. Both requirements have been originally successfully implemented for the ASUS Prime X299 Deluxe by our gorgeous @apfelnico with partial contributions of @TheOfficialGypsy. Many thanks for the extensive efforts and extremely fruitful and brilliant work! Subsequently, I adopted the ACPI DSDT Replacements and system SSDTs in concordance with SMBIOS iMacPro1,1. Some ACPI DSDT Replacements are still part of the config.plist contained in my actual respective X99 EFI-Folder distribution. Others are part of my System SSDTs provided in my X99-System-SSDTs Github repository.
 
Note that the ACPI DSDT Replacements in config.plist, System SSDTs and TB-SSDTs are build and PCIe slot population dependent and have to be verified and adopted or modified for all mainboards different from the ASUS X99-A II and builds or PCIe slot populations different from the one that constitutes the baseline of this guide.
 
For the ASUS X99-A II I will use in the following the PCIe Slot nomenclature depicted below:

 

357090044_ASUSX99-AII.thumb.png.688cde6aff1d15242d1a9efb55757c93.png

 

The verification and likely adaptation/modification can be performed by the help of IORegistryExplorer.

 

How to adopted or modify the ACPI DSDT Replacement Patches and System SSDT implementations is detailed within this short guideline by means of the OSXWIFI PCIe Adaptor implementation in PCIe Slot-3. I hope that by this specific example it rapidly becomes evident that the correct PCI Device implementation cannot be outlined for each individual "build-in" or "slot-specific" PCI device within this guide. The complexity and effort would just exceed by far all available capacities and indeed require the implementation of a separate guide and thread in addition. I therefore hope on your skills and flexibility to extend and apply the approach and methodology detailed above to any other "build-in" or "slot-specific" PCI device yet to be adopted or implemented

 

Important Note: It is strongly recommend to perform a stepwise SSDT PCI Device implementation, starting with one single specific PCI device. Once this PCI device has been successfully implemented, another SSDT PCI Device module can be added and verified. In case that the implementation of a specific PCI Device would be erroneous and fail, it would simply disappear from Section "PCI" of Apple's System report. To facilitate the stepwise PCI device implementation, the former SSDT-X99-iMacPro.aml has been split into separated modules now forming part of my X99-System-SSDTs Github repository.

 

Also keep always in mind to modify/adopt the ACPI replacements in your config.plist in parallel when ever necessary!
 
Note once more that the ACPI DSDT Replacements in config.plist and System SSDTs require SMBIOS iMacPro1,1.
 
E.9.1) ACPI DSDT Replacement Implementation

 

Note once more that all required ACPI DSDT Replacements are already implemented in the config.plist of my actual respective X99 EFI-Folder distribution or are directly part of of the System SSDTs provided in my X99-System-SSDTs Github repository. In the config.plist, the ACPI DSDT Replacements are disabled by default, thus we will now open the config.plist in the /EFI/CLOVER/ directory of our 10.14 System Disk EFI-Folder with Clover Configurator and stepwise adopt (if necessary) and enable the different required DSDT replacement patches in Clover Configurator Section "ACPI" under "DSDT patches", by also discussing their respective function and impact..
 
a.) OSI -> XOSI and EC0_ -> EC__ or H_EC  -> EC__ are DSDT replacement patches to achieve consistency with a real Mac variable naming.
 
i.) The XOSI functionality is required as explained by @RehabMan. Thus please enable the OSI -> XOSI DSDT Replacement patch.
 
ii.) On the ASUS X99-A II and ASUS X99 Deluxe II we have EC0 and H_EC controllers, which have to be renamed to 'EC' for proper USB power management. Thus enable both EC0_ -> EC__  and H_EC  -> EC__ DSDT Replacement Patches.
Comment:             Find*[Hex]      Replace [Hex]
OSI -> XOSI          5f4f5349        584f5349
EC0_ -> EC__         4543305f        45435f5f
H_EC  -> EC__        485f4543        45435f5f

 

b.) The HEC1 -> IMEI and IDER->MEID DSDT Replacement patches are Intel Management Engine Interface related and are vital as MacOS requires the variable names "IMEI" and "MEID" to load the 'AppleIntelMEIDriver'. The latter functionality solves the 'iTunes/Apple Store Content Access Problem' which is discussed here.
Please enable now both DSDT Replacement patches independent from your mainboard.
Comment:             Find*[Hex]       Replace [Hex]
HECI -> IMEI         48454331         494d4549
IDER->MEID           49444552         4d454944

 

c.) The LPC0 -> LPCB DSDT Replacement Patch is AppleLPC and SMBus related and is applied for consistency with the variable naming on a real Mac.
 
Please enable now this DSDT replacement patch independent from your mainboard.
Comment:             Find*[Hex]         Replace [Hex]
LPC0 -> LPCB         4c504330           4c504342

 

d.) FPU_->MATH, TMR_->TIMR, PIC_->IPIC are all DSDT Replacement Patches for consistency with the variable naming on a real Mac. The variables are however functionless on either X99 systems or real Macs.
 
Please enable now all three DSDT Replacement Patches independent from your mainboard.
Comment:             Find*[Hex]        Replace [Hex]
FPU_ -> MATH         4650555f          4d415448
TMR_ -> TIMR         544d525f          54494d52
PIC_ -> IPIC         5049435f          49504943

 

e.) The DSM -> XDSM DSDT replacement patch will be vital for loading the SSDT-ASUS-X99-A-II.aml, as all DSM methods used in the original DSDT do have a not compatible structure totally different from the real Mac environment. Without any fix, all DSM methods would be simply ignored. Note that one single device can have only one DSM method, which can assign additional properties to the respective device.
Thus please enable the latter DSDT replacement patch completely independent from your mainboard!
Comment:             Find*[Hex]         Replace [Hex]
_DSM -> XDSM         5f44534d            5844534d

 

f.) The 48 CPxx -> PRxx replacements are i7-6950X specific and result in a proper CPU core reordering as well as in a iMac Pro specific CPU core variable naming.
 
All i7-6950X users can now enable all 48 CPxx -> PRxx replacements. All users of CPUs different from the i7-6950X have to adopt/modify the 48 CPxx -> PRxx replacements in concordance with their original IOREG CPU core values.
Comment:             Find*[Hex]        Replace [Hex]
CP00 -> PR00         43503030          50523030
CP01 -> PR01         43503031          50523031
CP02 -> PR02         43503032          50523032
CP03 -> PR03         43503033          50523033
CP04 -> PR04         43503034          50523034
CP05 -> PR05         43503035          50523035
CP06 -> PR06         43503036          50523036
CP07 -> PR07         43503037          50523037
CP08 -> PR08         43503038          50523038
CP09 -> PR09         43503039          50523039
CP0A -> PR10         43503041          50523130
CP0B -> PR11         43503042          50523131
CP0C -> PR12         43503043          50523132
CP0D -> PR13         43503044          50523133
CP0E -> PR14         43503045          50523134
CP0F -> PR15         43503046          50523135
CP10 -> PR16         43503130          50523136
CP11 -> PR17         43503131          50523137
CP12 -> PR18         43503132          50523138
CP13 -> PR19         43503133          50523139
CP14 -> PR20         43503134          50523230
CP15 -> PR21         43503135          50523231
CP16 -> PR22         43503136          50523232
CP17 -> PR23         43503137          50523233
CP18 -> PR24         43503138          50523234
CP19 -> PR25         43503139          50523235
CP1A -> PR26         43503141          50523236
CP1B -> PR27         43503142          50523237
CP1C -> PR28         43503143          50523238
CP1D -> PR29         43503144          50523239
CP1E -> PR30         43503145          50523330
CP1F -> PR31         43503146          50523331
CP20 -> PR32         43503230          50523332
CP21 -> PR33         43503231          50523333
CP22 -> PR34         43503232          50523334
CP23 -> PR35         43503233          50523335
CP24 -> PR36         43503234          50523336
CP25 -> PR37         43503235          50523337
CP26 -> PR38         43503236          50523338
CP27 -> PR39         43503237          50523339
CP28 -> PR40         43503238          50523430
CP29 -> PR41         43503239          50523431
CP2A -> PR42         43503241          50523432
CP2B -> PR43         43503242          50523433
CP2C -> PR44         43503243          50523434
CP2D -> PR45         43503244          50523435
CP2E -> PR46         43503245          50523436
CP2F -> PR47         43503246          50523437

 

Resulting CPU Core Implementation

 

CPU-order.thumb.png.f34142f8958e09b50ca0c0011aa07ce9.png

 

 

E.9.2) System SSDT PCI Device Implementation

 

PCI.thumb.png.f7222d6e561efc28002fdc14375bf396.png

 

For the proper PCI device driver implementation (detailed in the figure above), we now have to revise and likely adopt or modify all System SSDTs provided within my X99-System-SSDTs Github repository.
 
Note that each SSDT contains a DefinitionBlock entry and the underlying PCI device implementation. In case of necessary modifications/adaptations, don't forget to also modify/adapt the respective DefinitionBlock entries in concordance with your IOREG entries. The entire SSDT structure is now completely module like. Each module can be independently added, changed or removed in dependence of your specific build, needs and requirements. A stepwise implementation of the individual PCI device modules is highly recommended!
 
E.9.2.1) HDEF - onboard Audio Controller PCI Implementation:
 
The SSDT-X99-HDEF.aml onboard Realtek ALC 1150 Audio Controller HDEF PCI device implementation is valid for the ASUS X99-A II and likely for all other mainboards with the same Audio Controller chipset. It is a build in device and does not have any slot specific dependency. Note the ALZA -> HDEF ACPI Replacement within the SSDT!
 
E.9.2.2) GFX0, HDAU - GPU and HDMI/DP Audio PCI implementation 
 
A.) Radeon RX Vega 64 GPUs
 
The SSDT-X99-Vega.aml GFX0 and HDAU PCI device implementation is valid for SMBIOS iMacPro1,1 (GFX0), the ASUS X99-A II and any Radeon RX Vega 64 GPU implemented in PCIe Slot 1.
 
It is a build and PCIe slot population dependent device implementation. Vega GPU users with more than one graphics card, with a Vega graphics card in a PCIe slot different from PCIe Slot 1, or with a mainboard different from the ASUS X99-A II will have to adopt the respective device path entries PCI0.BR3C, H000, H001, D077 and respective ACPI replacements by following their respective IOREG entries.
 
The above default Vega PCI device implementation performs an OC of an air-flow Nitro+ Vega 64 GPU of up to 1630 Mhz while considering an IDLE fan speed of 1500 Mhz. This seems sufficient to remain with GPU temps of about 80 deg C under GPU load conditions (e.g. Valley Benchmark), while not exceeding any comfortable noise level.
 
The latter Vega properties are achieved by means of a sophisticated "PP_PhmSoftPowerPlayTable", "PP_DisablePowerContainment" and "PP_FuzzyFanControl" SSDT implementation.
 
Everybody can change the respective Vega properties by means of VGTab-en.app, which provides a modified "PP_PhmSoftPowerPlayTable" (output-file VegaTab_64_data.txt), which can replace the "PP_PhmSoftPowerPlayTable", currently implemented in my SSDT-X99-Vega.aml distribution. E.g. users with a water-blocked Nitro+ Vega 64 like myself want to further screw the max. GPU OC frequencies, etc, while others might want to further improve the fan speed behaviour on air-flow Vegas..
 
Below the "PP_PhmSoftPowerPlayTable" for my custom water-blocked Sapphire Nitro+ Vega 64 8B (used on my Skylake-X/X299 system), with P7 Core Frequency of 1680 Mhz, P7 Core Voltage of 1200 mV, P3 Memory Frequency of 1050 Mhz and a Memory Voltage of 1350 mV.
 
PP_PhmSoftPowerPlayTable:

 

  0x9d, 0x02, 0x08, 0x01, 0x00, 0x5c, 0x00, 0x37,
  0x07, 0x00, 0x00, 0xec, 0x2b, 0x00, 0x00, 0x1b,
  0x00, 0x48, 0x00, 0x00, 0x00, 0x80, 0xa9, 0x03,
  0x00, 0xf0, 0x49, 0x02, 0x00, 0x32, 0x00, 0x08,
  0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
  0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x02, 0x01,
  0x5c, 0x00, 0x36, 0x02, 0x2d, 0x02, 0x94, 0x00,
  0x85, 0x01, 0xaf, 0x00, 0x19, 0x01, 0x7a, 0x00,
  0x8c, 0x00, 0xa3, 0x01, 0x00, 0x00, 0x00, 0x00,
  0x59, 0x02, 0x00, 0x00, 0x90, 0x00, 0x8f, 0x02,
  0x54, 0x01, 0x2a, 0x01, 0x7e, 0x01, 0x00, 0x71,
  0x02, 0x00, 0x71, 0x02, 0x02, 0x02, 0x00, 0x00,
  0x00, 0x00, 0x00, 0x00, 0x08, 0x00, 0x00, 0x00,
  0x00, 0x00, 0x00, 0x00, 0x04, 0x00, 0x07, 0x00,
  0x03, 0x00, 0x05, 0x00, 0x00, 0x00, 0x00, 0x00,
  0x00, 0x00, 0x01, 0x08, 0x20, 0x03, 0x84, 0x03,
  0xb6, 0x03, 0xe8, 0x03, 0x1a, 0x04, 0x4c, 0x04,
  0x7e, 0x04, 0xb0, 0x04, 0x01, 0x01, 0x46, 0x05,
  0x01, 0x01, 0x84, 0x03, 0x00, 0x05, 0x60, 0xea,
  0x00, 0x00, 0x00, 0xdc, 0x4a, 0x01, 0x00, 0x01,
  0x00, 0x77, 0x01, 0x00, 0x02, 0x90, 0x91, 0x01,
  0x00, 0x03, 0x6c, 0xb0, 0x01, 0x00, 0x04, 0x01,
  0x08, 0xd0, 0x4c, 0x01, 0x00, 0x00, 0x00, 0x80,
  0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x88, 0xbc,
  0x01, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00, 0x00,
  0x00, 0x00, 0x00, 0x98, 0xfc, 0x01, 0x00, 0x02,
  0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
  0x90, 0x0e, 0x02, 0x00, 0x03, 0x00, 0x00, 0x00,
  0x00, 0x00, 0x00, 0x00, 0x00, 0xc4, 0x2f, 0x02,
  0x00, 0x04, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
  0x00, 0x00, 0x70, 0x56, 0x02, 0x00, 0x05, 0x00,
  0x00, 0x00, 0x00, 0x01, 0x00, 0x00, 0x00, 0x60,
  0x7a, 0x02, 0x00, 0x06, 0x00, 0x00, 0x00, 0x00,
  0x01, 0x00, 0x00, 0x00, 0x40, 0x90, 0x02, 0x00,
  0x07, 0x00, 0x00, 0x00, 0x00, 0x01, 0x00, 0x00,
  0x00, 0x00, 0x03, 0x60, 0xea, 0x00, 0x00, 0x00,
  0xdc, 0x4a, 0x01, 0x00, 0x00, 0x90, 0x5f, 0x01,
  0x00, 0x00, 0x00, 0x08, 0x28, 0x6e, 0x00, 0x00,
  0x00, 0x2c, 0xc9, 0x00, 0x00, 0x01, 0xf8, 0x0b,
  0x01, 0x00, 0x02, 0x80, 0x38, 0x01, 0x00, 0x03,
  0x90, 0x5f, 0x01, 0x00, 0x04, 0xf4, 0x91, 0x01,
  0x00, 0x05, 0xd0, 0xb0, 0x01, 0x00, 0x06, 0xc0,
  0xd4, 0x01, 0x00, 0x07, 0x00, 0x08, 0x6c, 0x39,
  0x00, 0x00, 0x00, 0x24, 0x5e, 0x00, 0x00, 0x01,
  0xfc, 0x85, 0x00, 0x00, 0x02, 0xac, 0xbc, 0x00,
  0x00, 0x03, 0x34, 0xd0, 0x00, 0x00, 0x04, 0x68,
  0x6e, 0x01, 0x00, 0x05, 0x08, 0x97, 0x01, 0x00,
  0x06, 0xec, 0xa3, 0x01, 0x00, 0x07, 0x00, 0x01,
  0x68, 0x3c, 0x01, 0x00, 0x00, 0x01, 0x04, 0x3c,
  0x41, 0x00, 0x00, 0x00, 0x00, 0x00, 0x50, 0xc3,
  0x00, 0x00, 0x00, 0x00, 0x00, 0x60, 0x35, 0x01,
  0x00, 0x01, 0x00, 0x00, 0x28, 0x9a, 0x01, 0x00,
  0x02, 0x00, 0x00, 0x01, 0x08, 0x00, 0x98, 0x85,
  0x00, 0x00, 0x78, 0xb4, 0x00, 0x00, 0x60, 0xea,
  0x00, 0x00, 0x50, 0xc3, 0x00, 0x00, 0x01, 0x78,
  0xff, 0x00, 0x00, 0x40, 0x19, 0x01, 0x00, 0xb4,
  0x27, 0x01, 0x00, 0x50, 0xc3, 0x00, 0x00, 0x02,
  0x80, 0x38, 0x01, 0x00, 0xdc, 0x4a, 0x01, 0x00,
  0xdc, 0x4a, 0x01, 0x00, 0x50, 0xc3, 0x00, 0x00,
  0x03, 0xdc, 0x4a, 0x01, 0x00, 0x90, 0x5f, 0x01,
  0x00, 0x90, 0x5f, 0x01, 0x00, 0x50, 0xc3, 0x00,
  0x00, 0x04, 0x90, 0x5f, 0x01, 0x00, 0x00, 0x77,
  0x01, 0x00, 0x90, 0x5f, 0x01, 0x00, 0x50, 0xc3,
  0x00, 0x00, 0x05, 0x00, 0x77, 0x01, 0x00, 0x90,
  0x91, 0x01, 0x00, 0x90, 0x5f, 0x01, 0x00, 0x50,
  0xc3, 0x00, 0x00, 0x06, 0x6c, 0xb0, 0x01, 0x00,
  0x6c, 0xb0, 0x01, 0x00, 0x00, 0x77, 0x01, 0x00,
  0x50, 0xc3, 0x00, 0x00, 0x07, 0xc0, 0xd4, 0x01,
  0x00, 0xc0, 0xd4, 0x01, 0x00, 0x90, 0x91, 0x01,
  0x00, 0x50, 0xc3, 0x00, 0x00, 0x01, 0x18, 0x00,
  0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x0b, 0xe4,
  0x12, 0xdc, 0x05, 0xfc, 0x08, 0x41, 0x00, 0x0f,
  0x00, 0x54, 0x03, 0x90, 0x01, 0x90, 0x01, 0x90,
  0x01, 0x90, 0x01, 0x90, 0x01, 0x90, 0x01, 0x90,
  0x01, 0x00, 0x00, 0x00, 0x00, 0x00, 0x02, 0x04,
  0x21, 0x07, 0x08, 0x01, 0x08, 0x01, 0x08, 0x01,
  0x2c, 0x01, 0x00, 0x00, 0x4a, 0x00, 0x69, 0x00,
  0x4a, 0x00, 0x4a, 0x00, 0x5f, 0x00, 0x73, 0x00,
  0x73, 0x00, 0x64, 0x00, 0x40, 0x00, 0x90, 0x92,
  0x97, 0x60, 0x96, 0x00, 0x90, 0x46, 0x00, 0x00,
  0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
  0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x02,
  0x02, 0xd4, 0x30, 0x00, 0x00, 0x02, 0x10, 0x60,
  0xea, 0x00, 0x00, 0x02, 0x10

 

Note that I also changed the Nitro+ Vega 64 firmware to https://www.techpowerup.com/vgabios/200283/200283 (at BIOS jumper position 1). Don't forget to backup the original firmware, in case you return it to the seller! This thread might provide additional information in this context: https://forums.macrumors.com/threads/amd-polaris-vega-gpu-macos-support.2083168/.
 
As already mentioned before, within my current Vega SSDT PCI device implementation, all available ports on the Gigabyte Vega 64 (3x HDMI, 3x DP), including multi-monitor support and display hot plug are automatically and successfully implemented. However, it seems that DP-port issues (black screen) remain, when employing the respective Vega SSDT PCI device implementation on Sapphire Nitro+ Vega 64 (2x HDMI, 2xDP) or ASUS Strix Vega 64 (2x HDMI, 2x DP, 1x DVI) GPUs, which only can be removed by adding Whatevergreen.kext v.1.2.1. Within such configuration, multi-monitor support and display hot plug can be fully achieved also in case of the latter custom Vegas (both 10.13.6 SU and 10.14.1). Whatevergreen.kext only seems required for all Vegas possessing less than 6 physical ports (including the original Vegas like Frontier and Vega 64), else the current Vega SSDT PCI device implementation does pretty well it's job, including sleep/wake. 
 
SSDT-X99-Vega-Frontier.aml contains former Kamarang frame buffer SSDT implementation by @apfelnico for 1x Radeon Vega Frontier in PCIe Slot 1 of ASUS X99-A II.
 
B.) Radeon VII, Vega56, RX560 and RX580 GPUs

Note that there also Radeon VII, Vega56, RX580 and RX560 SSDTs available in my X99 SSDT Github repository, which likely need to be adopted depending on your motherboard and GPU PCIe slot population by following your original IOREG ACPI table information.
 
C.) Nvidia GPUs 
 
The actual SSDT-X99-Nvidia.aml GFX0 and HDAU PCI device implementation is valid for SMBIOS iMacPro1,1 (GFX0), the ASUS X99-A II and any Nvidia Graphics Card implemented in PCIe Slot 1.
 
It is a build and PCIe slot population dependent device implementation. Nvidia Graphics Card users with more than one GPU, with a Nvidia graphics card in a PCIe slot different from PCIe Slot 1 or on a mainboard different from ASUS, will have to adopt the respective PCI0, BR3C, H000, H001, D077, GFX0 ACPI path and ACPI replacements following their respective IOREG entries. 
 
Also note that with 10.13.4, Apple changed the com.apple.driver.AppleHDAController implementation. To make the NVIDIA HDAU PCI device driver work for e.g. a GeForce GTX 1080 Ti, one needs to add the following KextToPatch entry in Section "Kernel and kext Patches" of Clover Configurator, as already implemented but yet disabled in the config.plist contained in my actual respective X99 EFI-Folder distribution:
 
Name*                                 Find* [HEX]         Replace* [HEX]        Comment
com.apple.driver.AppleHDAController   DE100B0E            DE10EF10              FredWst DP/HDMI patch
 
Thus, please all Nvidia users enable and like adopt the NVIDIA HDAU patch for your particular Nvidia GPU in dependence of the respective device-id.
 
Credits to @FreedWst and thanks to @fabiosun for pointing me to this solution.
 
With Whatevergreen.kext, mis Nvidia users might be able to drop this KextToPatch entry, as the latter kext already properly implements the Nvidia HDAU PCI driver

 

 
E.9.2.3) XGBE - 10GBit NIC PCI Implementation:
 
SSDT-X99-ACQU.aml, SSDT-X99-X540-T1.aml and SSDT-X99-P2EI0G-2T.aml perform a 10-Gigabit NIC XGBE (XGBF) PCI implementation of an Acquantia AQC107-AFW, Intel X540-T1 or Small-Tree P2EI0G-2T 10GB NIC, respectively and are mainly of cosmetic nature. For each PCIe Adapter and for different PCIe slot populations or mainboard implementations, the XGBE PCI device implementation needs to be adopted/modified accordingly. This also states for the respective ACPI path entries "PCI0", "BR3A" and respective H000 -> D07C and D07C -> XGBE ACPI Replacements (in compliance with the iMac Pro 10GB ACPI variable nomenclature), directly performed within each SSDT. Those not employing any 10-GBit NIC in their system, can simply skip the corresponding SSDT PCI device implementation.
 
 
E.9.2.4) ETH0 - onboard LAN Controller PCI Implementation:
 
The SSDT-X99-ETH0.aml onboard Intel i218-V Ethernet controller ETH0 PCI implementation is of pure cosmetic nature and valid for the ASUS X99-A II or X99 mainboards with the same LAN Controller configuration. Owners of different X99 mainboards have to verify and adopt/modify the ACPI path and the PCI device implementations by means of their IOREG entries. Note the GLAN -> ETH0 ACPI replacement directly performed within the SSDT.
 
 
E.9.2.5) SAT1 - Intel AHCI SATA Controller PCI Implementation:
 
The SSDT-X99-SAT1.aml onboard Intel AHCI SATA controller SAT1 PCI device implementation is valid for the ASUS X99-A II and for all other X99 mainboards with the same AHCI SATA controller chipset.
 
 
E.9.2.6) EVSS - Intel X99 sSata Controller PCI Implementation:
 
The SSDT-X99-EVSS.aml onboard Intel X99 sSATA controller EVSS PCI device implementation is valid for the ASUS X99-A II and for all other X99 mainboards with the same X99 sSATA controller chipset. Verify and adopt/modify if necessary device path "PCI0.EVSS" and PCI device implementations by means of IOREG.
 
 
E.9.2.7)  ANS1 - NVMe Controller PCI Implementation:
 
The SSDT-X99-ANS1.aml Apple NVMe Controller ANS1 PCI implementation is of purely cosmetic nature and is valid for the ASUS X99-A II. Note  ACPI Replacements D075 -> D081 and D081 -> ANS2 directly performed within the SSDT, in concordance with the respective SMBIOS iMacPro1,1 variable naming!
 
 
E.9.2.8) - USBX:
 
When using the XHCI device name for USB (see the XHCI PCI Device Implementation below), one observes a bunch of USB Power Errors when booting the system. The SSDT-X99-USBX.aml PCI device implementation fixes this errors.
 
 
E.9.2.9) XHCI - onboard Extended Host Controller Interface (XHCI) PCI Implementation:
 
The SSDT-X99-XHCI.aml onboard USB3.0 controller XHCI PCI device implementation is valid for the ASUS X99-A II and for all other X99 mainboards with the same XHCI controller chipset. Verify and adopt/modify if necessary device path "PCI0.XHCI" and PCI device implementations by means of IOREG.
 
 
E.9.2.10) XHC2 - ASMedia ASM1142 USB 3.1 Controller PCI Implementation:
 
The SSDT-X99-XHC2.aml onboard ASMedia ASM1142 USB 3.1 AHCI SATA controller XHC2 PCI device implementation is valid for the ASUS X99-A II and for all other X99 mainboards with the same XHC USB3.1 controller chipset configuration. Note the D07D -> D082 and D082 -> XHC2 ACPI replacements directly performed within the SSDT!
 
 
E.9.2.11) ARPT - OSX WIFI Broadcom BCM94360CD 802.11 a/b/g/n/ac + Bluetooth 4.0 AirPort Controller PCI Implementation:
 
The SSDT-X99-ARPT.aml OSX WIFI Broadcom BCM94360CD 802.11 a/b/g/n/ac + Bluetooth 4.0 AirPort Controller PCI device implementation is of pure cosmetic nature and only valid for users of the latter WIFI/Bluetooth PCIe Adapter in PCIe Slot 5 of the ASUS X99-A II. Users of this PCIe Adapter within a PCIe slot population different from PCIe Slot 5 or on a mainboard different form the ASUS X99-A II  have to likely adapt/modify the respective device path "PCI0","RP07","ARPT". Users with a completely different WIFI/Bluetooth configuration have to adopt the entire Airport PCI implementation by means of IOREG.
 
 
E.9.2.12) GC-Titan Ridge / GC-Alpine Ridge / ASUS TBEX 3 Thunderbolt HotPlug System Implementation:
 
The current Thunderbolt development carefully focuses on iMac Pro SSDT-9.aml and DSDT.aml from @TheOfficialGypsy 's  iMac Pro dump, which appear to be the cornerstone for a correct, proper and complete Thunderbolt Hackintosh Local Node implementation.
 
The current development status is briefly reflected in posts

 and 

 

Constructive contributions by experts are highly desired.

 
Until reaching a complete Thunderbolt Hackintosh Local Node implementation, SSDT-X99-TB3HP-TTR.aml (for GC-Titan Ridge and ASUS TBEX 3) and SSDT-X99-TB3HP-APR.aml (for GC-Alpine Ridge) constitute workarounds for achieving TB HotPlug and TB XHC USB HotPlug functionality with the respective TB3 PCIe Add-In adopters. Note once more that with the GC-Titan Ridge, HotPlug functionality can be reached with the THB_C connected. For HotPlug with the other TB adaptors, the THB_C must be removed from most of the available mainboards.

For all TB3 SSDTs provided above, partial contributions by  by @apfelnico, @nmano, @Mork vom Ork, @Matthew82, @maleorderbride and @TheRacerMaster shall be mentioned and outlined. Their use with mainboards different from ASUS and within PCIe slot populations different from PCIe Slot 4 requires the adaptation/modification of respective ACPI path definitions ("PC01", "BR1A") or ACPI DSDT Table replacements (SL01 -> PEGP and PEGP -> UPSB), directly performed within the SSDTs.
 
 
 
E.9.2.13) DTGP Method:
 
SSDT-DTPG.aml is mandatory for all SSDT implementations listed above (note the external DTPG method call in the definition block of each respective SSDT) and must be always part of /EFI/Clover/ACPI/patched..
 
 
    External (DTGP, MethodObj)    // 5 Arguments (from opcode)
 
 
 
E.9.2.14) - Debugging Sleep Issues
 
For debugging sleep issues as proposed by Pike Alpha, one can add SSDT-SLEEP.aml to /EFI/CLOVER/ACPI/patched and follow Pike's comment and advices provided at https://pikeralpha.wordpress.com/2017/01/12/debugging-sleep-issues/
 
E.10) iMac Pro Boot Splash Screen Cosmetics 
 
Based on the ideas and instructions of @Matthew82, I achieved an iMacPro ASUS Boot Splash Screen
 
ASUS-Splash-Screen.png.19b30cd11094e87f395d7c1d9c2e8c79.png
 
by means of the following procedure:
 
1.) Installation of the BREW distribution:
 
a.) Open a terminal and change to "bash" shell.
bash

 

b.) Now enter the following "bash" terminal command and follow the standard BREW installation instructions:
/usr/bin/ruby -e "$(curl -fsSL https://raw.githubusercontent.com/Homebrew/install/master/install)"

 

2.) After the successful installation of the BREW distribution, we have to implement the QT5 distribution, again by using a "bash" terminal shell. Enter the following "bash" terminal commands:
brew install qt5
brew link qt5 --force

 

3.) After successfully implementing BREW and QT5 and if not already performed in Section B.1), we can now download the actual CodeRush UEFIPatch distribution from Github to our home directory with the following terminal command:
git clone https://github.com/LongSoft/UEFITool

 

4.) Now compile the UEFI Tool distribution with the following terminal commands:
cd /UEFITools/
qmake uefitool.pro
make

 

5.) Download and unzip iMacPro.raw to your Desktop.
 
6.) Now launch by UEFITool by clicking on the newly compiled UEFITool.app in the UEFITools Folder in your home directory.
 
a.) Select "File" -> "Open image file" and load your patched or unpatched BIOS Firmware distribution.
 
Select "Search.." in the UEFITool "Edit" Menu and perform a "GUID" search of "7BB28B99-61BB-11D5-9A5D-0090273FC14D" with "Header only"...
 
Guid-Search.png.3f8df668ab943fdd9305a6c283ef7649.png
 
You will receive a message "GUID pattern "7BB28B99-61BB-11D5-9A5D-0090273FC14D" found as .... in 7BB28B99-....". Double click on that message and search for the "Raw section" accompanying the "7BB28B99-...." entry, which indeed is the Boot Image, which you can easily verify by extracting the raw section body (right-click on "Raw section" and select "Extract body") to your Desktop and by subsequently opening the extracted raw-file directly with Apple's "Preview.app" (right-click an the raw file and select "Open with.." -> Preview.app).
 
b.) To exchange the default original ASUS Boot Logo image file stored in "Raw Section" by the iMacPro.raw image file that you previously downloaded to your Desktop,  right-click again on "Raw section", select this time "Replace body"  and select the iMacPro.raw image file on your Desktop.
 
UefiTool.png.757acdabe4f1de99964ad83bc9fb30a6.png
 
Note that the actual image dimension of iMacPro.raw (2131pix x 1457pix) was adopted for its use on my 38" LG 38UC99. For monitors with reduce screen resolution, iMacPro.raw might have to be adopted to an image dimension that suites your particular screen resolution, before its upload to "Raw section". If the Boot Logo image dimension is too big for your Monitor's screen resolution, you might just end up with a black screen during the BIOS initialisation at boot.
 
To do so, select in the Preview.app Menu -> "Tools" -> "Adjust Size". Change the image dimension and save the modified image with "File" -> "Export". In the "Export menu" press "Save", after selecting "JPEG" under "Format" , after choosing "Desktop" as the place to store the image, and after entering the new file name, which has to end with ".jpg".
 
Double-check by right-clicking on the resulting jpg image file and selecting "Get Info" that its file size does no exceed 200KB by far. If the latter would be the case, you would not be able to save the modified BIOS Firware file subsequently.
 
Finally just rename your new "XXXX.jpg" file to "XXXX.raw....
 
I guess, that by following the procedure detailed above, it is obvious that iMacPro.raw also can be substituted by any other image of your personal choice. Just be aware that it's background colour should be black (ecstatic reason for a its nice integration within the else black ASUS BIOS Boot Screen)
 
c.)  After replacing "Raw Section" with iMacPro.raw or the XXX.raw image of your choice, save your modified BIOS Firmware File with the Option "File" -> "Save Image File..."
 
d.) Copy your modified BIOS Firmware file to a USB3.0 Flash Drive, formatted with FAT32.
 
e.) Reboot, enter the Mainboard BIOS and save your BIOS settings to the USB Flash Drive
 
f.) Flash your mainboard BIOS with the modified BIOS Firmware
 
g.) Renter the Mainboard BIOS and restore your BIOS settings from the USB Flash Drive
 
h.) Save your restored BIOS settings with (F7) and (F10), reboot and you are done.
 
Just don't forget to set BIOS Setting "Boot Logo Display" to "Auto", when using this new approach. Any different setting might result in a black screen during BIOS initialisation.
 
 
E.11) iMac Pro Desktop Background Cosmetics 
 
It might be nice to equip your iMac Pro X299 also with the adequate iMac Pro Desktop Background.
 
1.) Download, unzip and copy imac-pro-wallpaper.jpg.zip to your Dektop
 
2.) Right-click with the mouse on your Desktop and select "Change Desktop Background.."
 
3.) In the left column click on the "+" and add your Desktop Folder
 
4.) Select imac-pro-wallpaper.jpg to be your new Desktop Background 
 
E.12) iStatMenus Hardware Monitoring
 
Thanks to extended tweet session between @BJango, @gxsolace and myself, we achieved a major step forward in properly monitoring Skylake-X/X299 Hardware with iStatMenus. iStatMenus v6.2 now correctly interfaces with the HWSensor and FakeSMC kext distribution provided by @interferenc and can now be also used for Broadwell-E/EP, Haswell-E/EP, X99 system monitoring. My distributed EFI-Folder already contains all necessary HWSensor and FakeSMC kexts.
 
The actual iStatMenus v6.2 distribution can be assessed at https://bjango.com/mac/istatmenus/
 
The actual HWSensor and FakeSMC kext distribution of @interferenc can be separately assessed at https://github.com/interferenc/HWSensors
 
To compile the the HWSensor and FakeSMC kexts of @interferenc, perform the individual steps detailed below:
 
1.)
git clone https://github.com/interferenc/HWSensors

2.)

cp HWSensors ~/Desktop/

3.)

cd ~/Desktop/HWSensors

4.)

xcodebuild -project Versioning\ And\ Distribution.xcodeproj/

5.)

xcodebuild -project HWMonitor.xcodeproj/

6.)

xcodebuild -project HWSensors.xcodeproj -alltargets

 

Subsequently, one finds the all compiled binaries in ~/Desktop/HWSensors/Binaries/.
 
Many thanks to both @interferenc and @Bjango for their awesome and extensive contributions and brilliant work!
 
Note that I recently modified the Kozlek/Interferenc Source Code distribution locally to also support GPU Temp sensor information for all Vegas and the new Radeon VII. In my recent 10.14 X99 EFI-Folder distributions, the resulting FakeSMC.kext and HWSensor.kexts supporting all Vegas already have been implemented by default in /EFI/CLOVER/kexts/Other. The actual 10.14.5 Beta X99 EFI-Folder distribution contains FakeSMC.kext and HWSensor.kexts also supporting the new Radeon VII.
 
Broadwell-E/EP, Haswell-E/EP, X99 iStatMenus Hardware Sensor Data:
 
1348105832_Screenshot2018-06-08at16_28_11.thumb.png.ac677c4b140308f5ed5893c899003ca4.png
 
Broadwell-E/EP, Haswell-E/EP CPU Thread Utilisation Graphs:
 
1265785417_Screenshot2018-06-08at16_33_40.png.4e7467ff6e4f4b5ec9bef07361618068.png
 
To change from CPU core to thread utilisation monitoring, uncheck "Hide Hyper-Threading cores" in Section "CPU & GPU" of iStatMenus Preferences.
 
iStatMenus-Preferences-1.png.642bb6d0282f23067347035e6d2d5064.png
 
Temperature unites can be adjusted between Celsius, Fahrenheit and Kelvin in Section "Sensors" of iStatMenus Preferences.
 
iStatMenus-Preferences-2.png.192f47c3202c8f8dc3b49438d8714b3b.png
 
 
F.) Benchmarking
 
F.1) i7-6950X CPU Benchmarks
 
 
xcpm.thumb.png.d32bd3df23f113177d6f298457a52e85.png
 
Geekbench-CPU.thumb.png.baecf0e42e8aa5950f9ac342ae4c7b45.png
 
Cinebench-CPU.png.32b70afaff9ca460ee66c12b0f29ed1d.png
 
 
 
F.2) Sapphire Nitro+ Radeon RX Vega 64 8GB (Air-Flow) OpenGL and Metal Benchmarks
 
LuxMark-OpenGL.png.f64cb889d9c37fbcff466cd6e571b7c5.png
 
438985678_LuxMark-OpenGLCPU.png.a01506912491b677f77a772abadd9cb8.png
 
Cinebench-OpenGL.png.f1227120ffc2161890338281a5e52e9e.png
 
Geekbench-OpenGL.thumb.png.fc3e4b2e41024bbedb71edebe8cb6d18.png
 
Geekbench-Metal2.thumb.png.77a46b2054028b20c0ecf8a9adb9e5b9.png
 
Heaven.png.cb8b6917afeb05e50a2aa9e72352aa1e.png
 
Valley.png.951eb90748520cc2e742d87bf1ad75ef.png
 
G.) Summary and Conclusions
 
Already under macOS 10.12 Sierra and macOS 10.13 High Sierra, Broadwell-E/EP, Haswell-E/EP, X99 systems reached full functionality together with flawless stability. Now with macOS 10.14 Mojave, it might be another opportunity to follow my iMac Pro Build and Desktop Guide to unfold the unbelievable Broadwell-E/EP, Haswell-E/EP, X99 potential!
 
High-end builds based on Broadwell-E/EP, Haswell-E/EP, X99 technology have found manifold application, not only in science and research at universities or research institutions, engineering facilities, or medical labs, etc... Broadwell-E/EP, Haswell-E/EP, X99 with up to 22 cores (44 threads) and turbo frequencies up to 4.4 GHz have made X99 to a "relatively cheap" but really serious alternative to real iMac Pro's and Mac Pro's. The principal intention of my desktop guides is to demonstrate, that we are able to build and configure fully functional and relatively "low-cost" high-end systems, which go far beyond of what Apple is able to offer at present or will be ever able to offer for some reasonable pricing. Broadwell-E/EP, Haswell-E/EP, X99 Systems that allow the use of all software-packages developed for MacOS, Unix, Linux or even Windows at the same time (e.g. think on Vine, Parallels, or a dual boot system configuration). The flexibility between different mainboards (Asus, Gigabyte, ASRock, MSI, etc.), different Broadwell-E/EP, Haswell-E/EP processors, and different RAM memory configurations (16-128GB) make such systems affordable for anybody (also home office, audio and video editing/production, etc.) and allows their perfect adaptation for each specific purpose, requirement and available budget. It might not be necessary to outline, that current Broadwell-E/EP, Haswell-E/EP, X99 Systems perform absolutely stable on a 24/7/365 basis.
 
I am a scientist, expert in solar physics, space weather forecast and related telescope/instrument/space-mission development. In the frame of my scientific research, I developed parallelized image reconstruction, spectral line inversion and numerical modeling algorithms/applications, which require tremendous parallelized calculation power, RAM memory and storage capacities to reduce, analyze and interpret extensive and pioneering scientific ground-based or space-born observational data sets. This basically was also the professional motivation for developing innovative iMac Pro macOS Builds iSPOR-S (imaging Spectropolarimetric Parallel Organized Reconstruction Servers running iSPOR-DP, the Imaging Spectropolarimetric Parallel Organized Reconstruction Data Pipeline software package for the GREGOR Fabry-Pérot Interferometer, located at the 1.5m GREGOR Solar Telescope (Europe's largest solar telescope) on Tenerife, Canary Islands, Spain) as well as for the entire related iMac Desktop Guide Development, which naturally shall also be of benefit for others.  Anybody interested can find more details on my personal webpage.
 

post-1362934-0-41431100-1516222345.png

 

 

Edited by KGP-iMacPro
Guide update 10.14.3

Share this post


Link to post
Share on other sites
Advertisement

Guide History Log:

 

06.06.2018: Writing up Guide

 

08.06.2018: Guide setup complete. Enjoy and have fun.. :wink_anim:

 

10.06.2018: Implementation of new EFI-Folder EFI-X99-10.14-DP1-Release-iMacPro1,1-100618.

EFI-Folder related changes: Adding SMCHelper-64.efi and VBoxHfs-64.efi in /EFI/Clover/drivers64UEFI/ solved the issue with the USB macOS Installer partition being invisible in the Clover Boot Loader Menu. Sorry for any inconvenience caused by the previous EFI-Folder distribution

 

16.06.2018: Implementation of new EFI-Folder EFI-X99-10.14-DP1-Release-iMacPro1,1-160618.

EFI-Folder related changes:  Implementation of Boot Loader Clover_v2.4k_r4548; Removal of aspf.efi from /EFI/CLOVER/drivers64UEFI/; Adding ApfsDriverLoader.efi to /EFI/CLOVER/drivers64UEFI/; Adding AGPMEnabler.kext to/EFI/CLOVER/kexts/Other (thanks to @apfelnico)

Guide related changes:  Update of Section C.3) with explanations to aspf.efi, ApfsDriverLoader.efi and Clover Package Creation.

 

18.06.2018: Modifications of Vega 64 and Frontier SSDT implementations.  

 

24.09.2018: System and Guide Update to 10.14.0 (18A391); Guide related changes: New Section D.2) with manual and automatic "Install macOS Mojave.app" full package installer creation approach; Revised Section E.7) GC-Titan Ridge / GC-Alpine Ridge /Asus TBEX 3 PCIe Add-In Implementation; Revised Section E.9.2) with new System SSDTs; Revised Section E.9.13) GC-Titan Ridge / GC-Alpine Ridge / Asus TBEX 3 Thunderbolt HotPlug System Implementation;  New EFi-Folder EFI-X99-10.14.0-Release-iMacPro1,1-240918.zip; EFI-Folder related changes: Implementation of Clover_v2.4k_r4674; Removal of Beta Boot Flags for Lilu and Lilu Plugins from config.plist; Implementing 10.14.0 _xcpm performance patch in config.plist. 

 

31.10.2018: Guide update to macOS Mojave 10.14.1 (18B75). Modified section E.4 - USB Configuration for 10.14.1 USB2.0 and USB3.0 compatibility. New EFI-Folder EFI-X99-10.14.1-Release-iMacPro1,1-311018.zip. EFI-Folder related changes: Implementation of Clover_v2.4k_r4726; Adding Lilu.kext 1.2.8 and AppleALC.kext 1.3.3; Disabling AppleUSBXHCI USB port limit kexts patch in config.plist..non functional under 10.14.1.

 

05.11.2018: Another revision of Section E.4) - USB Configuration.

 

06.12.2018: Guide update to macOS Mojave 10.14.2 (18C54). New EFI-Folder EFI-X99-10.14.2-Release-iMacPro1,1-101218.zip . EFI-Folder related changes: Implementation of Clover_v2.4k_r4805; Implementation of new FakeSMC and HWSensor distribution; Implementation of 10.14.2 xcpm_performance_patch.

 

23.01.2019: Guide update to macOS Mojave 10.14.3 (18D42). New EFI-Folder EFI-X99-10.14.3-Release-iMacPro1,1-230119.zip. EFI-Folder related changes: Implementation of Clover_v2.4k_r4859; Implementation of latest AppleALC and Lilu distributions; Implementation of 10.14.3 xcpm_performance_patch.

 

02 February 2019: New EFI-Folders EFI-X99-10.14.3-Release-iMacPro1,1-020219.zip and EFI-X99-10.14.4-Beta1-Release-iMacPro1,1-020219.zip with Clover_v2.4k_r4862, working USB port limit patches and a macOS independent XCPM_performance patch valid for 10.13.4+ and all version of 10.14. Fully vanilla EFI-Folders that should work with 10.13.4+ and all versions of 10.14, always provided that one also uses a truncated 15-port XHC USB kext in addition, with disabled USB port limit patches in the config.plist. There are still separate EFI-Folders for 10.14.3 and 10.14.4 Beta1, in case that somebody still wants to use a fully implemented XHC USB kext and the necessary respective USB port limit patches, which are disabled by default in the config.plist of each respective EFI-Folder distribution.

 

25 March 2019: Guide update to 10.14.4. New 10.14.4 EFI-Folder distribution EFI-X99-10.14.4-Release-iMacPro1,1-250319.zip in the X99 EFI-Folder Github repository. Clover_v2.4k_r4903 and new 10.14.4 USB port limit patch implementation. Updated FakeSMC and HWSensor distribution. Implementation of latest Lilu.kext and AppleALC.kext distributions. One should also add latest and Whatevergreen.kext distribution. Still no native vanilla Radeon VII macOS implementation (still no default Radeon VII device-ID 0x66AF1002 in the vanilla AMDRadeonX5000.kext). Also note new Xcode 10.2 and Xcode 10.2 Command Line distributions.

 

05 April 2019: New X99 10.14.5 Beta EFI-Folder distribution EFI-X99-10.14.5-Beta-iMacPro1,1-050419.zip. EFI-Folder related changes: Clover_v2.4k_r4918, Lilu.kext v.1.3.5 + AppleALC.kext v1.3.6, new XCPM_pkg_scope kernel patch for 10.14.5. I also modified Kozlek/Interferenc FakeSMC/HWSensor source code distribution for adding Radeon VII GPU Temp sensor information and subsequently added new FakeSMC.kext and HWSensor.kexts to /EFI/Clover/kexts/Other. The new GPU Sensor kext should now support all Vegas and also the new Radeon VII, when using iStatMenus.

Edited by KGP-iMacPro

Share this post


Link to post
Share on other sites

@KGP-iMacPro Just a quick note for:

2.) With the macOS Mojave 10.14 DP1 (18A293u) Installer Package in your /Application Folder,  connect your USB Flash Drive (named USB) and run the following terminal command:

sudo /Applications/Install\ macOS\ 10.14\ Beta.app/Contents/Resources/createinstallmedia --volume /Volumes/USB --applicationpath /Applications/Install\ macOS\ 10.14\ Beta.app --nointeraction

is now:

sudo /Applications/Install\ macOS\ 10.14\ Beta.app/Contents/Resources/createinstallmedia --volume /Volumes/USB --nointeraction

--applicationpath is deprecated for 10.14.

Share this post


Link to post
Share on other sites
6 hours ago, Pavo said:

@KGP-iMacPro Just a quick note for:

2.) With the macOS Mojave 10.14 DP1 (18A293u) Installer Package in your /Application Folder,  connect your USB Flash Drive (named USB) and run the following terminal command:


sudo /Applications/Install\ macOS\ 10.14\ Beta.app/Contents/Resources/createinstallmedia --volume /Volumes/USB --applicationpath /Applications/Install\ macOS\ 10.14\ Beta.app --nointeraction

is now:


sudo /Applications/Install\ macOS\ 10.14\ Beta.app/Contents/Resources/createinstallmedia --volume /Volumes/USB --nointeraction

--applicationpath is deprecated for 10.14.

 

Thanks, man! corrected !

Share this post


Link to post
Share on other sites

If anyone Intel Gadget not work well try this patch

EIST Performance fix by @PMheart for 10.14 Edit by NMano

Find

C1E30848 63D389D0 48C1EA20 B9990100 000F3048 FF057348 73004883 C4085B5D C30F1F40 00

Replace

BB00FF00 004863D3 89D048C1 EA20B999 0100000F 3048FF05 73487300 4883C408 5B5DC390 90

Share this post


Link to post
Share on other sites
On 6/19/2018 at 7:36 AM, nmano said:

If anyone Intel Gadget not work well try this patch

EIST Performance fix by @PMheart for 10.14 Edit by NMano

Find

C1E30848 63D389D0 48C1EA20 B9990100 000F3048 FF057348 73004883 C4085B5D C30F1F40 00

Replace

BB00FF00 004863D3 89D048C1 EA20B999 0100000F 3048FF05 73487300 4883C408 5B5DC390 90

 

That's exactly the patch I am using in my EFi-Folder distributions anyway.... Stopped working again with 10.14 DP2, despite the updated Broadwell-E Performance Kernel patch. No OC with 10.14 DP2 so far. BTW... I would not call it EIST Performance fix, as it does not work with EIST enabled anyway. 

Edited by KGP-iMacPro

Share this post


Link to post
Share on other sites

If you Can please upload DP2 kernel

Thanks.

Share this post


Link to post
Share on other sites

Try this

Performance patch PMHeart DP2 Edit By N.Mano

C1E30848 63D389D0 48C1EA20 B9990100 000F3048 FF0593AE 76004883 C4085B5D C30F1F40 00

 

 

BB00FF00 004863D3 89D048C1 EA20B999 0100000F 3048FF05 73487300 4883C408 5B5DC390 90

Share this post


Link to post
Share on other sites
2 hours ago, nmano said:

Try this

Performance patch PMHeart DP2 Edit By N.Mano

C1E30848 63D389D0 48C1EA20 B9990100 000F3048 FF0593AE 76004883 C4085B5D C30F1F40 00

 

 

BB00FF00 004863D3 89D048C1 EA20B999 0100000F 3048FF05 73487300 4883C408 5B5DC390 90

 

Already implemented as provided to me by @PMheart yesterday night.. Does not work at all, as the original performance patch in 10.14 DP1 also only worked in conjunction with the SMT_scope kernel patch and EIST disabled.  Like in case of 10.13.5, I also need the pkg_scope kernel patch for successfully booting my X99 system.

Edited by KGP-iMacPro

Share this post


Link to post
Share on other sites

With patches in 10.13 I have 27K in Geekbench, and in 10.14 with patches from the first post only 20K. Someone compared the results?

Share this post


Link to post
Share on other sites
22 minutes ago, ACIDSky said:

With patches in 10.13 I have 27K in Geekbench, and in 10.14 with patches from the first post only 20K. Someone compared the results?

 

The EFI-Folder in the first post has not been updated yet for 10.14 DP2. As implemented currently, it provided perfect OC along 10.14 DP1. BTW.. similar issues also state for 10.13.6 Beta 2 and 3, while OC was working perfectly fine under 10.13.6 Beta 1, just by applying the respective performance patches. 

 

Your current poor benchmark results under 10.14 DP2 are in line with what we are just discussing right now here above..    

Edited by KGP-iMacPro

Share this post


Link to post
Share on other sites
2 hours ago, KGP-iMacPro said:

 

The EFI-Folder in the first post has not been updated yet for 10.14 DP2. As implemented currently, it provided perfect OC along 10.14 DP1. BTW.. similar issues also state for 10.13.6 Beta 2 and 3, while OC was working perfectly fine under 10.13.6 Beta 1, just by applying the respective performance patches. 

 

Your current poor benchmark results under 10.14 DP2 are in line with what we are just discussing right now here above..    

such result in 10.14 dp1, I did not update to dp2

 

 

Edited by ACIDSky

Share this post


Link to post
Share on other sites
54 minutes ago, ACIDSky said:

such result in 10.13 dp1, I did not update to dp2

 

 

 

10.13 DP1? You mean 10.14 DP1?  What about your mainboard BIOS firmware? Up-to-date? I don't know about your BIOS settings or any additional EFI-Folder configuration.. I even don't know, which mainboard or CPU you actually employ.. Difficult to trace back your issues.. 

Edited by KGP-iMacPro

Share this post


Link to post
Share on other sites
Upcoming iStatMenus v.6.20
 
Note the release of a iStatMenus 6.20 Beta for testing purposes: files.bjango.com/istatmenus6/is…
 
Many former bugs have been apparently removed. 
 
If you still witness remaining issues, report back to @bjango on twitter. 
 
Enjoy and have fun,
 
kgp.png.75676e26a1d9badd5daf66f7f02ded65.png

Share this post


Link to post
Share on other sites

Does this guide work for the X99-A USB 3.1 board as well? I don't know if the USB 3.1 edition and the Mk II version (which this article is about) would work with the same everything. I'm trying to get my X99-A USB 3.1 edition working with Mojave but there's not much info on it. I'd rather not squander many more of my scarce hours if i don't have to. following this guide alone would take enough time as it is. 

Share this post


Link to post
Share on other sites
3 hours ago, kobe80 said:

Does this guide work for the X99-A USB 3.1 board as well? I don't know if the USB 3.1 edition and the Mk II version (which this article is about) would work with the same everything. I'm trying to get my X99-A USB 3.1 edition working with Mojave but there's not much info on it. I'd rather not squander many more of my scarce hours if i don't have to. following this guide alone would take enough time as it is. 

 

Why not? My guide should be compatible with all X99 mainboards..  

Share this post


Link to post
Share on other sites

macOS Mojave 10.14.2 Beta 2 (18C38b)

 

1412434780_Screenshot2018-11-08at12_27_15.png.97c9b985a3a8f150859283a1e289f0e1.png

 

macOS: 10.14.2
Build: 18C38b
_xcpm performance_patch
Find: C1E3084863D389D048C1EA20B9990100000F3048FF05B37076004883C4085B5DC30F1F4000
Repl: B800FF00004863D389D048C1EA20B9990100000F3048FF05B37076004883C4085B5DC39090

 

468699017_Screenshot2018-11-08at12_33_37.thumb.png.b0d59aaac778c26bc39720b0df3f35e7.png

 

1517265653_Screenshot2018-11-08at12_34_28.thumb.png.51fd00c0c29e324fcde58eb3d82ec7a1.png

 

549027000_Screenshot2018-11-08at12_37_51.thumb.png.e5e932c4f5183dcc4751b4ca7b7cf551.png

 

1167253746_Screenshot2018-11-08at12_38_11.thumb.png.e961b1b8e01d35f190a5b56451ce9aa5.png

 

 

Enjoy and have fun,

 

 kgp.png.d56e1490a215b13090c3925e757c635a.png

Share this post


Link to post
Share on other sites

Question: KGP does not tells me to install clover boot loader to the usb installer, am I correct? Or do I miss something here? I want to update my Asrock X99m Extreme4 hackintosh from El Capitan to Mojave but I always have problems with creating the usb installer to boot from. Do I really just need to copy the EFI folder decribed in C and D Section to the EFI Partition? in the past, clover was always needed for bootup. 

Share this post


Link to post
Share on other sites
15 minutes ago, Multisaft said:

Question: KGP does not tells me to install clover boot loader to the usb installer, am I correct? Or do I miss something here? I want to update my Asrock X99m Extreme4 hackintosh from El Capitan to Mojave but I always have problems with creating the usb installer to boot from. Do I really just need to copy the EFI folder decribed in C and D Section to the EFI Partition? in the past, clover was always needed for bootup. 

 

Dude, the Clover boot loader is already part of my EFI-Folder distribution.... :wink_anim:

Share this post


Link to post
Share on other sites
On 11/15/2018 at 3:17 AM, 8car said:

Hi,KGP. I'm back. I have a supermico board x10dai, with dual E5 2683v3. It's easy to install the Mojave 10.14.1,  I tried all of the performance patches but none of them  did work.  XCPM  does not registered. Can you help me ? Here is all my files.

https://www.insanelymac.com/forum/applications/core/interface/file/attachment.php?id=313398

 

Did you download and implement my actual X99 10.14.1 EFI-Folder distribution: https://github.com/KGP/X99-EFI-Folder-Distributions/blob/master/EFI-X99-10.14.1-Release-iMacPro1%2C1-221118.zip

 

What about adopting and enabling the _xcpm_bootstrap Kernel patch in the config.plist? See README.md of https://github.com/KGP/X99-EFI-Folder-Distributions!  

Share this post


Link to post
Share on other sites
On 11/24/2018 at 9:57 PM, KGP-iMacPro said:

 

Did you download and implement my actual X99 10.14.1 EFI-Folder distribution: https://github.com/KGP/X99-EFI-Folder-Distributions/blob/master/EFI-X99-10.14.1-Release-iMacPro1%2C1-221118.zip

 

What about adopting and enabling the _xcpm_bootstrap Kernel patch in the config.plist? See README.md of https://github.com/KGP/X99-EFI-Folder-Distributions!  

sure, When I used the _xcpm_bootstrap Kernel patch,I will stop at here.  XCPM  registered. but stoped here.

 221101.thumb.jpg.44aafa72f2a5e583fa3f9d2f9951f1c8.jpg

 

 

 

 

Share this post


Link to post
Share on other sites
1 minute ago, 8car said:

sure, When I used the _xcpm_bootstrap Kernel patch,I will stop at here.  XCPM  registered. but stoped here.

 221101.thumb.jpg.44aafa72f2a5e583fa3f9d2f9951f1c8.jpg

 

 

 

 

 

Did you properly adopt and add TSCAdjustReset.kext

Share this post


Link to post
Share on other sites
Guest
This topic is now closed to further replies.

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By fusion71au
      Run Vanilla OS X El Capitan, Sierra, High Sierra or Mojave in VirtualBox 5.x.x on a Windows Host
      Following on from my previous guide on how to create a VMware virtual machine running Vanilla OS X El Capitan in Windows, I’ve decided to write a similar guide for creating a VirtualBox El Capitan VM. 
       
      The virtual machine should be useful for testing El Capitan and also for creating installers for use on a real machine/hackintosh.
       
      There are other tutorials and videos on the net about running OS X on Windows machines using pre-made VMDK disk images but you can never guarantee what else is in there….
       
      I’ve gathered info for this guide from several threads in the Multibooting and Virtualisation section of this forum and also the wider internet eg
       
      @colt2 HOW TO: Create a bootable El Capitan ISO for VMware
      @dsmccombs comment on faking Ivybridge Processor
      @E:V:A http://forum.xda-developers.com/showpost.php?p=55572430&postcount=6
      @Tech Reviews video tutorial https://www.youtube.com/watch?v=t7X07U63lwg.
      VirtualBox Forum: Status of OSX on OSX
       
      Requirements
         Intel PC with four or more CPU cores running Windows 7 X64 or later OS (2 or more cores needed for OS X)    4GB or more RAM (2GB or more will be needed for OS X)    Hard Disk with at least 40GB free for Virtual Machine    Oracle VM VirtualBox v 5.0.34    Install OS X El Capitan app and Mac or Hack to prepare installation iso <-- Now, no longer necessary to have previous access to a Mac or Hack by building the Installer.app from scratch - see post#75    16GB or larger exFAT formatted USB stick to transfer El Capitan iso from Mac/Hack to Host PC  
      Prepare Installation ISO on your Mac or Hack
      1.  On your Mac or Hack, download "Install OS X El Capitan.app" from the App Store into your Applications folder.
      2.  Download and unzip the CECI.tool (attached to this post) into your ~/Downloads folder. The commands in this executable script are shown below for informational purposes.  Note: you will need approx 16GB of free space on your hard disk for the script to complete.
       
       
       
      3.  Open OS X terminal, then run the following commands to execute the script:
      cd downloads chmod +x CECI.tool ./CECI.tool 4.  At the end of the process, you will have an El Capitan iso on your desktop - copy this onto an exFAT formatted USB for use on the PC Host later.
       
       
      Create an El Capitan Virtual Machine in VirtualBox
      1.  Open the VirtualBox program and click the "New" button to create a new VM.
       

       
      2.  Select Mac OS X and Mac OS X 10.11 El Capitan (64 -bit) for Operating System type and version.  I named my Virtual Machine "El_Capitan", then clicked next...
       

       
      3.  Leave the Memory size at the recommended 2048 MB, then click next.
       

       
      4.  Choose to "Create a virtual hard disk now", then click the create button.
       

       
      5.  For the hard disk file type, the default is VDI (VirtualBox Disk Image) but I have selected VMDK for inter-operability with VMWare.  Click next...
       

       
      6.  For Storage on physical hard disk, I have chosen the default Dynamically allocated (grows larger to a set limit as you need more disk space).
       

       
      7.  On the File location and size screen, you can set the location of the new virtual hard disk and its size - I recommend changing disk size to 40GB or larger.  When you click the create button, you will now see your new VM in the VirtualBox main GUI.
       

       
      8.  Click the settings button on the Main Menu to tweak a few settings....
         a.  On the System/Motherboard tab in Boot Order, you can uncheck the Floppy Drive (who has these now?)
       

       
         b.  On the System/Processor tab, you can increase the allocated CPU cores to 2
       

       
         c.  On the Display tab, you can increase the allocated Video Memory to 128MB
       

       
         d.  On the Storage tab, click on the icon of the Optical Drive and select "Choose Virtual Optical Disk File". 
       

       
      Navigate and select the El Capitan ISO we created earlier...
       

       
         e.  Click the OK button to finalise the VM settings.
       
       
      Patch El Capitan vbox configuration file with DMI Settings from a Mac
      1.  From the start menu, type cmd and click run as administrator to open an administrative command prompt. 
       

       
      2.  Choose a Mac Model similar to your host system, then type the following lines, followed by <enter>  after each line.  Make sure you first close all VirtualBox Windows and the VirtualBox program, otherwise any changes you make won't stick...
       
      Eg iMac11,3
      cd "C:\Program Files\Oracle\VirtualBox\" VBoxManage setextradata "El_Capitan" "VBoxInternal/Devices/efi/0/Config/DmiSystemProduct" "iMac11,3" VBoxManage setextradata "El_Capitan" "VBoxInternal/Devices/efi/0/Config/DmiSystemVersion" "1.0" VBoxManage setextradata "El_Capitan" "VBoxInternal/Devices/efi/0/Config/DmiBoardProduct" "Mac-F2238BAE" VBoxManage setextradata "El_Capitan" "VBoxInternal/Devices/smc/0/Config/DeviceKey" "ourhardworkbythesewordsguardedpleasedontsteal(c)AppleComputerInc" VBoxManage setextradata "El_Capitan" "VBoxInternal/Devices/smc/0/Config/GetKeyFromRealSMC" 1 MacBookPro11,3
      cd "C:\Program Files\Oracle\VirtualBox\" VBoxManage setextradata "El_Capitan" "VBoxInternal/Devices/efi/0/Config/DmiSystemProduct" "MacBookPro11,3" VBoxManage setextradata "El_Capitan" "VBoxInternal/Devices/efi/0/Config/DmiSystemVersion" "1.0" VBoxManage setextradata "El_Capitan" "VBoxInternal/Devices/efi/0/Config/DmiBoardProduct" "Mac-2BD1B31983FE1663" VBoxManage setextradata "El_Capitan" "VBoxInternal/Devices/smc/0/Config/DeviceKey" "ourhardworkbythesewordsguardedpleasedontsteal(c)AppleComputerInc" VBoxManage setextradata "El_Capitan" "VBoxInternal/Devices/smc/0/Config/GetKeyFromRealSMC" 1 Macmini6,2
      cd "C:\Program Files\Oracle\VirtualBox\" VBoxManage setextradata "El_Capitan" "VBoxInternal/Devices/efi/0/Config/DmiSystemProduct" "Macmini6,2" VBoxManage setextradata "El_Capitan" "VBoxInternal/Devices/efi/0/Config/DmiSystemVersion" "1.0" VBoxManage setextradata "El_Capitan" "VBoxInternal/Devices/efi/0/Config/DmiBoardProduct" "Mac-F65AE981FFA204ED" VBoxManage setextradata "El_Capitan" "VBoxInternal/Devices/smc/0/Config/DeviceKey" "ourhardworkbythesewordsguardedpleasedontsteal(c)AppleComputerInc" VBoxManage setextradata "El_Capitan" "VBoxInternal/Devices/smc/0/Config/GetKeyFromRealSMC" 1 3.  Optional- For some host systems eg those with Haswell and newer CPUs, you might have to spoof an older CPU to avoid VirtualBox errors.  You can try from one of the following if this happens:

      To spoof Lynnfield i5 750 CPU
      VBoxManage.exe modifyvm "El_Capitan" --cpuidset 00000001 000106e5 06100800 0098e3fd bfebfbff To spoof IvyBridge CPU
      VBoxManage.exe modifyvm "El_Capitan" --cpuidset 00000001 000306a9 04100800 7fbae3ff bfebfbff or
      VBoxManage.exe modifyvm "El_Capitan" --cpuidset 00000001 000306a9 00020800 80000201 178bfbff 4.  Close the command prompt window.
       
       
      Installation of El Capitan
      We are now ready to start the El_Capitan Virtual Machine....
       



       
      Installation should be relatively straight forward, just following the prompts of the OS X installer:
      1.  Select language, agree to legal terms
       

       
      2.  Use Disk Utility from the Utilities Menu to erase and format the virtual hard drive as a single partition GUID Mac OS X Extended.  I named my drive "Macintosh HD" but you can enter whatever you like eg El_Capitan.
       

       
      3.  Quit DU and choose Macintosh HD to install El Capitan on.
      4.  After 20-30 min (depending on how fast your system is), the installation will complete.  At this point, unmount the El Capitan ISO by clicking the Devices menu from the VM window, click Optical Drives, then choose Remove disk from virtual drive.  The VM is now ready to reboot into OS X from the virtual hard drive.
      5.  At the welcome screen, choose your country and keyboard layout.  You can skip transfer information, location services and logging in with your Apple ID if you wish…
      6.  Create a User Account and select your Time Zone.  You can skip sending diagnostics and usage data to Apple….
      7.  Finally, you will arrive at the El Capitan Desktop.
       

       
      8.  Network/internet and audio should work OOB but on my system, the sounds were distorted.  Unfortunately, there is no QE/CI and the VM resolution will be fixed without the ability to dynamically resize the VM window (no VirtualBox additions for OS X guests atm). 
       
       
      Customization with VBoxManage
      1.  You can change the default resolution of 1024*768 (after shutting down the VM) with the VBoxManage command from the Windows Administrative Command Prompt:
      cd "C:\Program Files\Oracle\VirtualBox\" VBoxManage setextradata "El_Capitan" VBoxInternal2/EfiGopMode N (Where N can be one of 0,1,2,3,4,5) referring to the 640x480, 800x600, 1024x768, 1280x1024, 1440x900, 1920x1200 screen resolution respectively.
       
      Update:  For VirtualBox 5.2.x, the command for changing screen resolution has changed...
       
      VBoxManage setextradata "<MyVM>" VBoxInternal2/EfiGraphicsResolution XxY (where X=Horizontal screen resolution, Y=Vertical screen resolution)
      eg
      VBoxManage setextradata "<MyVM>" VBoxInternal2/EfiGraphicsResolution 1280x1024 2.  Adding serials and other SMBIOS details for the System Information Screen
      VBoxManage setextradata "El_Capitan" "VBoxInternal/Devices/efi/0/Config/DmiSystemSerial" "W8#######B6" VBoxManage setextradata "El_Capitan" "VBoxInternal/Devices/efi/0/Config/DmiBoardSerial" "W8#########1A" VBoxManage setextradata "El_Capitan" "VBoxInternal/Devices/efi/0/Config/DmiSystemVendor" "Apple Inc." VBoxManage setextradata "El_Capitan" "VBoxInternal/Devices/efi/0/Config/DmiSystemFamily" "iMac" VBoxManage setextradata "El_Capitan" "VBoxInternal/Devices/efi/0/Config/DmiBIOSVersion" "IM112.0057.03B" A listing of known issues with Mac OS X guests can be found in the VirtualBox Manual - link https://www.virtualbox.org/manual/ch14.html.
       
      Vanilla Mavericks and Yosemite, Snow Leopard from Retail DVD
      The same VM settings for El Capitan will also boot and run vanilla installations of OS X Mavericks and Yosemite .  Attached to this post are installer scripts to create bootable Mavericks (CMI.tool) and Yosemite (CYI.tool) ISOs for VirtualBox and VMware.
       
      With the respective OS X installer apps in the Applications folder, download and run the installer tools using terminal ie
       
      To create a Mavericks ISO on your desktop
      cd downloads chmod +x CMI.tool ./CMI.tool To create a Yosemite ISO on your desktop
      cd downloads chmod +x CYI.tool ./CYI.tool Here is a screenshot of the VM running Mavericks 10.9.5...
       

       
      Finally, those without a Mac/Hack to prepare the install media can purchase a retail Snow Leopard DVD directly from Apple and install OSX 10.6.3 on their virtual machines (Snow Leopard, Lion and Mountain Lion run quite happily in VirtualBox with 1 CPU, 1-2 GB of RAM and the rest of the settings unchanged from above).  Once you update by combo update to SL 10.6.8, you can directly download El Capitan from the App Store for free .
       

       
      UPDATE macOS Sierra 10.12 to 10.12.6: For macOS Sierra, use CSI.tool in post#51.
      UPDATE macOS High Sierra 17A365:  For macOS High Sierra, use CHSI.tool in post#73.
      UPDATE macOS Mojave 18A391:  For macOS Mojave or High Sierra, use macOS_iso_creator.tool on page 4 of thread.
      UPDATE macOS Catalina Beta DP3_19A501i:  For Catalina, @jpz4085 has made an automated batch file to create a Catalina VM in Windows with iMac 14,2 SMBIOS.  You can still use my macOS_iso_creator.tool on page 5 to make an installer ISO to attach to the VM.
       
       
       
      Good luck and enjoy
      CECI.tool.zip
      CYI.tool.zip
      CMI.tool.zip
    • By fusion71au
      Run Vanilla OS X El Capitan, Sierra, High Sierra or Mojave in VMware Workstation on a Windows Host
       
      I wanted to make a simple guide on how to create a vanilla OS X El Capitan virtual machine running on a Windows host.  The virtual machine should be useful for testing El Capitan and also for creating installers for use on a real machine/hackintosh.
       
      There are many guides and videos on the net about running OS X on Windows machines using pre-made VMWare disk images but you can never guarantee what else is in there….
       
      I’ve gathered info for this guide from various threads in the Multibooting and Virtualisation section of this forum eg
       
      Workstation 11/12, Player 7/12, Fusion 7/8 and ESXi 6 Mac OS X Unlocker 2 by @Donk How to Install OS X 10.x from Snow Leopard to El Capitan in VMware Workstation 10/12, Player 6/8 or ESXi 5/6 by @MSOK HOW TO: Create a bootable El Capitan ISO for VMware Credit and thanks to @Donk, @Albert Nietsnie and @MSOK for all their hard work in creating and testing the VMware Unlocker program.
       
      Requirements
      Intel PC with four or more CPU cores running Windows 7 X64 or later OS (2 or more cores needed for OS X) 4GB or more RAM (2GB or more will be needed for OS X) Hard Disk with at least 40GB free for Virtual Machine VMware Workstation 12 or later VMware Unlocker 2.0.7 or later Install OS X El Capitan app and Mac or Hack to prepare installation iso <-- Now, no longer necessary to have previous access to a Mac or Hack by building the Installer.app from scratch - see post#41 16GB or larger exFAT formatted USB stick to transfer El Capitan iso from Mac/Hack to Host PC Prepare Installation ISO on your Mac or Hack
      1.  On your Mac or Hack, download "Install OS X El Capitan.app" from the App Store into your Applications folder.
      2.  Unmount any attached install image/InstallESD.dmg (if currently mounted) by rebooting the system or running the hdiutil unmount command in terminal eg
       
      3.  Download and unzip the CECI.tool (attached to this post) into your ~/Downloads folder. The commands in this executable script are shown below for informational purposes….
       
       
       
      4.  Open OS X terminal, then run the following commands to execute the script:
      cd downloads chmod +x CECI.tool ./CECI.tool 5.  At the end of the process, you will have an El Capitan iso on your desktop - copy this onto an exFAT formatted USB for use on the PC Host later.
       
      Updates:
      @shela has created an ISO generating script compatible with OS X 10.6-10.12: create_osx_iso post #362.
      See post#30 for macOS_iso_cim.tool script to create ISO for macOS 10.13+ using Apple's createinstallmedia utility.
       
      Install and Patch VMware Workstation 12 on your PC
      1.  Download and install VMWare Workstation Player 12 or later
      2.  Download and extract Unlocker 2.0.7 or later to your USB stick…
      3.  Run the win-install.cmd as administrator by right clicking the file in Windows explorer or run it from an Administrative Command Prompt.
       



       
      Create an El Capitan Virtual Machine
      1.  Double click on the VMware Workstation 12 Player icon on your desktop and click “Create a New Virtual Machine”.  Choose “I will install the operating system later” at the How will you install screen….
       

      2.  Select Apple Mac OS X as the Guest operating system and OS X 10.11 as the version.  By default, an OS X 10.11 folder will be created in your Documents\Virtual Machines folder.
       


      3.  Under Specify Disk Capacity, you can leave the default 40GB or set a larger value.  I personally store the virtual disk as a single file.  Click Finish and you will see OS X 10.11 on the Main Screen of Workstation 12.
       


      4.  Next, we need to edit the virtual machine settings to map the virtual SATA CD/DVD drive to the El Capitan installation iso we created earlier.
       


       
      5.  To prevent the virtual machine from crashing in Windows, the virtualHW.version set in the vmx configuration file needs to be changed from 12 to 10 (alternatively, the line smc.version = "0" can be added to the file).  The OS X 10.11.vmx file can be edited with the WordPad program (navigate to the OS X 10.11 virtual machine folder with Windows Explorer and right click on the file to open in WordPad).
       


       
      6.  For HW10, set USB compatibility to USB 2.0, otherwise your mouse and keyboard might not work in the virtual machine.
       

      7.  Finally click “Play virtual machine”
       

      Installation of El Capitan
      Installation should be relatively straight forward, just following the prompts of the OS X installer:
      1.  Select language, agree to legal terms
       

      2.  Use Disk Utility from the Utilities Menu to erase and format the virtual hard drive as a single partition GUID Mac OS X Extended.  I’ve named the drive Macintosh HD but you can enter whatever you like eg El_Capitan.
       



      3.  Quit DU and choose Macintosh HD to install El Capitan on.
       

      4.  After 20-30 min (depending on how fast your system is), the installation will complete and the VM will automatically reboot…
       

      5.  At the welcome screen, choose your country and keyboard layout.  You can skip transfer information, location services and logging in with your Apple ID if you wish…
       


      6.  Create a User Account and select your Time Zone.  You can skip sending diagnostics and usage data to Apple….
       


      7.  Finally, you will arrive at the El Capitan Desktop.  You should eject the Installation iso now by right clicking and selecting “Eject OS X Base System”.  This will allow you to install VMware Tools….
       



      8.  After rebooting, the VM can now be resized or run at full screen resolution.  Audio and network/internet should also work OOB.
       

       
      SMBIOS Customization and iMessage Vars
      To make the Virtual Machine more "Mac like", you can edit the vmx file to add unique identifiers from a real Mac's SMBIOS -
      eg for an iMac 11,3 SMBIOS, you can enter the following lines....
      smbios.reflectHost = "FALSE" board-id.reflectHost = "FALSE" board-id = "Mac-F2238BAE" hw.model.reflectHost = "FALSE" hw.model = "iMac11,3" serialNumber.reflectHost = "FALSE" serialNumber = "W80#######6" Refer How to spoof real Mac in VMware - Multi-booting and Virtualisation.
       
      The critical variables for iMessage/Facetime activation are MLB & ROM.  By default, VMware "reflects" the host's MLB and ROM since it assumes you are running the OSX guest on a real Mac host - see post#42 by @Donk.
       
      If the host is a Windows PC, the following lines need to be added to the vmx file (requires virtualHW.version 12 and smc.version = "0")....
      efi.nvram.var.ROM.reflectHost = "FALSE" efi.nvram.var.MLB.reflectHost = "FALSE" system-id.enable = "TRUE" and the MLB, ROM and optionally system-id entered manually eg
      efi.nvram.var.MLB = "W80######BA1A" (MLB can be 13 or 17 characters long, alphanumeric string) efi.nvram.var.ROM = "<=>?@A" (ROM is entered here as a 6 character ASCII string) uuid.bios = "## ## ## ## ## ## ## ##-## ## ## ## ## ## ## ##" <---Optional (if you want to inject a given system-id hexadecimal value) Note the output for ROM from imessage_debug is a 12 character hexadecimal that needs to be entered here as a 6 character ASCII string eg using an Hex to ASCII converter we find that "3c3d3e3f4041" hex is equivalent to   "<=>?@A".
       
      Vanilla Mavericks and Yosemite
      The same VM settings for El Capitan will also boot and run vanilla installations of OS X Mavericks and Yosemite .  Attached to this post are installer scripts to create bootable Mavericks (CMI.tool) and Yosemite (CYI.tool) ISOs for VirtualBox and VMware.
       
      With the respective OS X installer apps in the Applications folder, download and run the installer tools using terminal ie
       
      To create a Mavericks ISO on your desktop
      cd downloads chmod +x CMI.tool ./CMI.tool To create a Yosemite ISO on your desktop
      cd downloads chmod +x CYI.tool ./CYI.tool Here is a screenshot of the VM running Mavericks 10.9.5...
       

       
      Enjoy
       
      Update for macOS 10.12 Sierra
      The above settings still work for macOS Sierra after upgrading to VMware Workstation 12.5 and unlocker 2.0.8 - see post #13.
       
      Update for macOS 10.13 High Sierra and 10.14 Mojave
      See post#30 for macOS_iso_cim.tool script to create ISO for macOS using Apple's createinstallmedia utility.
      Post#41 describes how to build "Install macOS ******.app" on the fly from installer files downloaded beforehand in /SharedSupport folder.
       
      Update for macOS 10.15beta Catalina
      See post Update for macOS Catalina 10.15beta
       
      CECI.zip
      CYI.tool.zip
      CMI.tool.zip
    • By crazybirdy
      Patched OSInstaller.framework to allow macOS 10.14 installation on MBR HFS+ partition.
       
      To use those patched files you must follow HowTo to create an USB installer. You can't just run the app downloaded from Mac App Store.
      The patch is made base on 落下爱@pcbeta 10.10.x MBR patch method, and more patch for 10.14 HFS Firmware check by crazybirdy.
       
      What is this patched OSInstaller doing?
      1. Patch the MBR check, allow macOS 10.14 installation on MBR partition.
      2. Patch the Firmware check, bypass the error of "An error occurred while verifying firmware".
      3. Patch to stop auto-convert to APFS , "ConvertToAPFS=false" is no longer worked with 10.14.
      4. This patched MBR OSInstaller will never convert to APFS, and will always install as HFS+ partition.
      5. This patched MBR OSInstaller method works with both MBR HFS+ and GPT HFS+ partition (GPT+recovery).
      No longer need to set new SMbiosversion, FirmwareFeatures, and FirmwareFeaturesMask with this MBR-patch.
       
      What's the difference between createinstallmedia method, MBR-Manual-Method, and MBR-Automatic-Method?
      As the following....
      1. createinstallmedia method,
          needs stage 1, stage 2 installation process, which is worked with GUID partition only, always convert to APFS format.
      2. MBR-Manual-Method (same as 10.12),
          install via stage 2 manually, which is worked with both MBR and GUID, HFS+ and APFS, will never convert the partition format.
          We can manually format as MBR or GPT, HFS+ or APFS on installation screen like as 10.12.
          We can manually select MBR HFS+ partition to install 10.13 and 10.14 on installation screen now.
          Needn't to update the MBR-Manual-Method files, it will still work on 10.13, and 10.14 future versions, I think so.
          It can be installed as Fresh installation on formated blank partition only, but can't be installed as update from previous version.
      3. MBR-Automatic-Method (new for 10.13+),
          install via stage 2 automatically, which is worked with both MBR and GUID, HFS+ and APFS, will never convert the partition format.
          It can be installed as Fresh installation on formated blank partition, and can be installed as update from previous version.

      How to make 10.14 installer for MBR (MBR-Manual-Method)?
      Just use EasyMBR-InstallerMaker to make installer, it works with both MBR and GPT.
      Read HowTo inside the dmg first, same as 10.12.
      Read HowTo Q/A Q5. How to patch to work with CPU SSE4.1 only for Mojave?
      Read HowTo Q/A Q6. How to download the full installer app via swscan.apple.com, instead of App Store?
      Read HowTo Q/A Q7. How to update 10.14.x combo-update to MBR and GPT with installScript directly?
       
      How to make 10.14 installer for MBR (MBR-Automatic-Method)?
      Just use 14MBRinstallerMaker to make installer, it works with both MBR and GPT.
      Read HowTo inside the dmg first, same as 10.13.
      Read HowTo Q/A Q5. How to patch to work with CPU SSE4.1 only for Mojave?
      Read HowTo Q/A Q6. How to download the full installer app via swscan.apple.com, instead of App Store?
      Read HowTo Q/A Q7. How to update 10.14.x combo-update to MBR and GPT with installScript directly?
       
      And, need a SMBIOS supported with /System/Library/CoreServices/PlatformSupport.plist.
       


       
      Q6. How to download the full installer app via swscan.apple.com, instead of App Store?
      A6. Some people download installer app from App Store, and get only 18 MB size, not the complete installer app (5.68 GB). You should boot to 10.12, or 10.13 to download it again from App Store, or use script Q6-DownloadFullApp/installScript_1014fullapp to download the full installer app via swscan.apple.com.
       

       
    • By fusion71au
      Patch Catalina or Mojave macOS Installer App for Unsupported Machines
       
      Often for economic reasons, Apple prevents the Installer.app for its latest macOS from installing on older machines perfectly capable of running it eg macOS 10.14 Mojave on Unsupported Macs Thread.
       

       
      In Mojave 10.14, @ASentientBot posted a method to patch the distribution file in OSInstall.mpkg to enable the Mojave installer to install on unsupported machines (with or without graphics card metal support). 
       
      In Catalina 10.15beta, the above method no longer works since Apple is checking OSInstall.mpkg for its file signature and the mandatory requirement in Catalina to install to 2 separate apfs volumes necessitates using the original Catalina macOS Base System Installer.  Fortunately, it is still possible to substitute High Sierra’s Apple Signed OSInstall.mpkg inside the Catalina or Mojave InstallESD.dmg by making it R/W.
       
      The procedure below will allow Macs or Hacks able to install High Sierra to also install Catalina or Mojave (eg SMBIOS MacPro5,1, iMac11,3, MacBook Pro7,1 which have been unsupported in macOS 10.14.x and 10.15beta) -credit to @ASentientBot's post.
       
      Prerequisites
      1. Mac or Hack capable of and running High Sierra 10.13.x
      2. An original, untouched copy of OSInstall.mpkg from High Serra InstallESD.dmg - attached OSInstall_10.13.6.mpkg.zip save to your ~/Downloads folder
      3. macOS Installer App eg for Catalina beta or Mojave downloaded to /Applications
      4. Add NVRAM boot arg (or Clover config.plist boot arg on a hack) -no_compat_check to enable system to boot to final completed Mojave or Catalina install.
       
      Procedure
      1. Open Terminal and type the following
       
      open /Applications/Install*/Contents/SharedSupport/InstallESD.dmg (assuming the Catalina or Mojave Installer App is in /Applications)  
      2. Open Disk Utility, click File|New Image|Image from ‘InstallESD”
      3. Save as read/write image, no encryption in /Applications
      4. Unmount InstallESD in DU by clicking the "eject" icon next to it
       
       
      5. Open the R/W InstallSD.dmg in /Applications and replace Catalina’s/Mojave's OSInstall.mpkg with High Sierra’s version by typing in terminal
       
      open /Applications/InstallESD.dmg cp ~/Downloads/OSInstall_10.13.6.mpkg /Volumes/InstallESD/Packages/OSInstall.mpkg  
      6. Unmount InstallESD in DU by clicking the "eject" icon next to it
      7. Replace original Catalina/Mojave InstallESD.dmg with our patched one, making a backup of the original.  In terminal, type
       
      sudo mv /Applications/Install*/Contents/SharedSupport/InstallESD.dmg /Applications/InstallESD_orig.dmg sudo mv /Applications/InstallESD.dmg /Applications/Install*/Contents/SharedSupport/  
      8.  Test the newly patched installer!…

    • By mfkk
      I install Mojave by following RehabMan Guide. After install I copy the Intel HD4000 7 series Config.plist from RehabMan. In my system configuration shows 1536MB graphics but I don't get the graphics performance . I have graphics related problems and lags issues. dock don't have transperancy, browsers have black shade and don't see fonts etc. I try many config files but I can't fix the issue still now. When I try some config file it will be fix until restart or shutdown. After that I have still graphics problem. Over a month I try to fix this I didn't get any result still now. Please help me to fix this . I'm first time in Hackintosh and I don't have knowledge about it.
       
      Intel HD4000 Graphics with 1366x786 (8086/0166)
      i3 processor
      6gb ram
      123gb ssd