Jump to content
Sign in to follow this  
Followers 0
zcmckenna

Graphics Artifacting/Broken Graphics

1 post in this topic

Recommended Posts

I have been having a pretty major issue with my new Hackintosh lately. It has been displaying broken link images in safari (See image 1). It has also had certain areas of artifacting such as the storyboard in Xcode (See image 2). and finally PDFs have been showing up completely blacked out (See image 3). This has been a big issue for me and I was wondering if any of you have had the same problem and have had any luck fixing it. I have already tried display calibration and switching to integrated graphics. Thanks in advance!

(See attached for config.plist)

Specs:

CPU: i5-8600k

MB: Gigabyte Z370XP SLI

GPU: ASUS 1070 Dual

RAM: 16GB Ballistix (8GB x 2)

HDD: WD Blue 1TB

426044060_ScreenShot2018-05-13at3_58_48PM.thumb.png.776d2f98d8b515a955c06ef80e4d8eb5.png

510403337_ScreenShot2018-05-13at10_03_37PM.thumb.png.7e2c0ae537c93a7e0072e6d41380a1d8.png

1912812770_ScreenShot2018-05-15at7_49_50PM.thumb.png.9c5eb367759d307a9049e1067e1400e9.png

config.plist

Edited by zcmckenna
Fixed CPU model

Share this post


Link to post
Share on other sites
Advertisement

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  
Followers 0

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By metaphysician
      hi folks! i'm just checking for opinions here on a Clover based install of High Sierra. currently i can't boot directly from the internal drive on my hackbook, an ASUS ROG GL502-VS laptop (with the replaced WiFi card), though i can boot from the USB bootloader/installer

      i installed 10.13.6 fine using a prepared vanilla installer on HFS+ (not APFS), but my configuration is somewhat unusual. i have two drives. the first SSD has the Windows system, the second has two partitions with the 2nd partition holding the macOS system. when i ran Clover installer i could not use the UEFI option to copy to the EFI partition because it couldn't find one on that drive. so it installed the EFI folder on the root of the macOS partition instead.
       
      however, after a bit of tinkering around, i found out that there is an existing EFI partition on the primary drive called SYSTEM. it has a EFI folder and underneath that is a Windows folder, a Boot folder, and one called APPLE. i can mount this partition with Clover Configurator and copy files to it, but i don't know if this is a good or risky solution. i was thinking i would manually copy the CLOVER folder and the uefi64.boot file to this partition , making sure not to overwrite anything existing. using the UEFI setup, i can create a boot path from the SYSTEM partition to the Clover boot file, but i'm just curious if this is a useful solution or not, and i don't want to ruin the existing Windows 10 installation for sure. any advice appreciated!
    • By wmchris
      This tutorial has been updated on GITHUB to 10.14 and 10.15
      the tutorial on insanelymac got too fragmented for a simple forum thread and will not be updated, but still be used for discussion and hints, tips and tricks
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
      Dell XPS 15 (9550, Version of 2016) Sierra 10.13.1 Tutorial

       

       
       
       
       
       
      Before we start:
      this installation includes real time DSDT/SSDT patching from within clover. This is pretty easy to install. But it is NOT suited for people with no or only few knowledge in Hackintosh Systems. If you only know how to copy commands in your shell and you dont know what they're doing, then stop the tutorial and revert to windows or buy a real mac. Even if you get it running: this system is not failsafe and will be broken multiple times in its usage time, where you have to fix it without a tutorial.
      Optional steps are marked in GREEN, System dependent steps are BLUE

      English is not my mother-tongue and i'm writing this without proof reading, so please forgive my bad spelling
      If you've questions or something doesn't work: first check if you've done all steps of this tutorial! If yes: please read the whole thread (doesn't matter how long it is) before asking to prevent multiple questions. Additionally do a search in google and this forum.


      Credits:
      Many knowledge of "how to hackintosh a dell in the first place" by the tutorial of @Gymnae http://www.insanelymac.com/forum/topic/319766-dell-xps-9550-detailled-1011-guide/
      Using many kexts and solutions from @RehabMan

      What's not working:
      Hibernation (works somehow, but high chance to destroy your whole data), Sleep works fine! SD-Card reader Killer 1535 Wifi (rarely used, need replace) nVidia Graphics card (Intel works) FileVault 2 (full HDD encryption) Requirements:
      one working MAC OS X Enviroment 16GB USB Stick (larger is sometimes not bootable and/or requires advanced partitioning) MacOS High Sierra 10.13.1 installation file from the app store (redownload, just in case) Knowledge in PLIST editing USB Harddrive for backup - you'll loose all data on your computer! Step 1: Prepare Installation
      Use the existing Mac to download the Sierra installer from the App Store and create a bootable USB stick with CLOVER. You can do this with the App "Pandora's Box" of insanelymac (use google for download link), which is pretty easy to use.
      Optional: check if your SSD can be switched to 4k sector size. This prevents NVMe corruption. See https://github.com/wmchris/DellXPS15-9550-OSX/blob/10.13/4k_sector.md
      After you've finished you need to download the Dell XPS 15 specific configurations for clover.
      Link: https://github.com/wmchris/DellXPS15-9550-OSX/archive/10.13.zip and unzip this file or checkout git directly:
      git clone https://github.com/wmchris/DellXPS15-9550-OSX.git You only need the folder 10.13, you can delete the 10.11. I'll refer to this folder by "git/"
      Now mount the hidden EFI partition of the USB Stick by entering
      diskutil mount EFI Inside the terminal. Mac OS will automaticly mount the EFI partition of the USB stick, but just in case: make sure it really is
      Overwrite everything in the CLOVER folder of the partition EFI with the content of git/10.13/CLOVER.
      If your PC has a Core i5 processor, you'll have to modify your config.plist in EFI/EFI/CLOVER/: search for the Key ig-platform-id: 0x191b0000 and replace it with 0x19160000.
      If you could use the 4k sector patch, replace the config.plist with the 4kconfig.plist. 
      If you use a hynix device and you didnt do the 4k sector switch, you'll have to add the following patch to your config.plist
      <key>Comment</key> <string>IONVMeFamily Pike R. Alpha Hynix SSD patch</string> <key>Disabled</key> <false/> <key>Find</key> <data>9sEQD4UcAQAA</data> <key>Name</key> <string>IONVMeFamily</string> <key>Replace</key> <data>9sECD4UcAQAA</data> Go into the EFI Configuration (BIOS) of your Dell XPS 15:
       
      Also disable the SD-Card Reader to reduce the power consumption drastically. Insert the stick on the Dell XPS 15 and boot it up holding the F12 key to get in the boot-menu and start by selecting your USB-Stick (if you've done it correctly it's named "Clover: Install macOS Sierra", otherwise it's just the brandname of your USB-Drive). You should get to the MacOS Installation like on a real mac. If you're asked to log-in with your apple-id: select not now! Reason: see Step 5.


      Step 2: Partition and Installation
      INFORMATION: after this step your computer will loose ALL data! So if you haven't created a backup, yet: QUIT NOW!

      Dont install macOS yet. Select the Diskutil and delete the old partitions. Create a new HFS partition and name it "OSX". If you want to multiboot with Windows 10, then you'll have to create a second partition, too (also HFS! Dont use FAT or it will not boot! You have to reformat it when installing Windows). Make sure to select GUID as partition sheme.
      Close the Diskutil and install OSX normally. You'll have to reboot multiple times, make sure to always boot using the attached USB stick. So dont forget to press F12. After the first reboot you should see a new boot option inside clover, which is highlighted by default. Just press enter. If you only see one, then something went wrong.


      Step 3: Make it bootable
      After a few reboots you should be inside your new macOS enviroment. You can always boot into it using the USB stick. Remove the USB drive after successful bootup. Enter
      diskutil mount EFI in your terminal, which should mount the EFI partition of your local installation.

      install git/Additional/Tools/Clover_v2.4k_r4003.pkg. Make sure to select "Install Clover in ESP". Also select to install the RC-Scripts. This should install the Clover Boot System. Now copy everything from git/10.13/CLOVER to EFI/CLOVER like you did before by creating the usb stick. (if you had to modify the config.plist in step 1, do it here, too). Your system should be bootable by itself. Reboot and check if your system can boot by itself.

       
      Step 4: Post Installation
      Because all DSDT/SSDT changes are already in the config.plist, you dont need to recompile your DSDT (albeit i suggest doing it anyway to make your system a lil bit more failsafe, see gymnaes El-Capitan tutorial for more informations). So we can skip this part and go directly to the installation of the required kexts. Open a terminal and goto the GIT folder.
      sudo cp -r ./Post-Install/LE-Kexts/* /Library/Extensions/ sudo mv /System/Library/Extensions/AppleACPIPS2Nub.kext /System/Library/Extensions/AppleACPIPS2Nub.bak 2> /dev/null sudo mv /System/Library/Extensions/ApplePS2Controller.kext /System/Library/Extensions/ApplePS2Controller.bak 2> /dev/null sudo ./AD-Kexts/VoodooPS2Daemon/_install.command Now you'll have to replace the config.plist. Because you'll install modified kexts you'll HAVE TO replace the config.plist in your installation. Otherwise your PC will not boot anymore.
      diskutil mount EFI replace EFI/CLOVER/config.plist with git/Post-Install/CLOVER/config.plist. Again: if your PC has a Core i5 processor, search the config.plist for the Key ig-platform-id: 0x191b0000 and replace it with 0x19160000.

      OPTIONAL (in case you've audio problems):
      AppleHDA has some problems after Wake-Up. You'll have to plug in a headphone to get your speakers working again. You can use VoodooHDA instead, which breaks the headphone jack most of the time, but makes the rest much more stable.
      sudo rm -r /Library/Extensions/CodecCommander.kext sudo rm /EFI/EFI/CLOVER/ACPI/patched/SSDT-ALC298.aml then remove from your config.plist from the key "KextsToPatch" the elements "AppleHDA#1" to "AppleHDA#7". Install the package: git/Post-Install/AD-Kexts/VoodooHDA-2.8.8.pkg
      i also suggest moving some of the kext from EFI/CLOVER/kexts/10.13 to /Library/Extensions. It's just more stable.
      Finalize the kext-copy by recreating the kernel cache:
      sudo rm -rf /System/Library/Caches/com.apple.kext.caches/Startup/kernelcache sudo rm -rf /System/Library/PrelinkedKernels/prelinkedkernel sudo touch /System/Library/Extensions && sudo kextcache -u / sometimes you'll have to redo the last command if your system shows "Lock acquired".
      OSX 10.12.2 removed the posibility to load unsigned code. You can enable this by entering
      sudo spctl --master-disable If you're using the 4K monitor, you'll have to copy the UHD enabling kexts to your clover directory:
      sudo cp ./Post-Install/AD-Kexts/UHD-Kexts/* /EFI/EFI/CLOVER/kexts/10.13/ To enable GPU acceleration: Edit your clover config file again and remove the following block from it:
       
      To prevent getting in hibernation (which can and will corrupt your data), just set the default sleep mode to "suspend to ram" (sleep) instead of "suspend to disk" (hibernation)
      sudo pmset -a hibernatemode 0 To get HDMI Audio working:
      Search for your Boarrd-ID in the config.plist and open /S/E/AppleGraphicsControl.kext/contents/plugin/AppleGraphicePolicy.kext/contents/info.plist with a texteditor. Search for your board-id in there and change the value of it from "Config2" to "none"
       
      OPTIONAL (alternative power management):
      the whole power management is done by intels speed step technology (HWP), which is enabled in the clover config. If you want to let OSX manage the power management, you'll have to do these steps:
      sudo cp ./Post-Install/CLOVER/ACPI/optional/SSDT.aml /EFI/EFI/CLOVER/ACPI/patched/ then open the config.plist (/EFI/EFI/CLOVER/config.plist) and change <key>HWPEnable</key><true/> to <key>HWPEnable</key><false/>.
       
      Step 5: iServices (AppStore, iMessages etc.)
       
      WARNING! DONT USE YOUR MAIN APPLE ACCOUNT FOR TESTING! It's pretty common that apple BANS your apple-id from iMessage and other services if you've logged in on not well configured hackintoshs!
      If you want to use the iServices, you'll have to do some advanced steps, which are not completly explained in this tutorial. First you need to switch the faked network device already created by step 4 to be on en0. Goto your network settings and remove every network interface.
      sudo rm /Library/Preferences/SystemConfiguration/NetworkInterfaces.plist Reboot, go back in the network configuration and add the network interfaces (LAN) before Wifi.

      You also need to modify your SMBIOS in the config.plist of Clover in your EFI partition with valid informations about your "fake" mac. There are multiple tutorials which explain how to do it like "http://www.fitzweekly.com/2016/02/hackintosh-imessage-tutorial.html".

      It's possible you have to call the apple hotline to get your fake serial whitelisted by telling a good story why apple forgot to add your serial number in their system. (aka: dont do it if you dont own a real mac). I personally suggest using real data from an old (broken) macbook.


      Step 6: Upgrading to macOS 10.13.2 or higher / installing security updates
      Each upgrade will possibly break your system!
      (Update: after the latest updates in this tutorial the system should be update-proof.) 
       
      Step 7: Fixes / Enhancements / Alternative Solutions / Bugs
      See: https://github.com/wmchris/DellXPS15-9550-OSX/blob/10.13/Tutorial_10.13_Step7.md
       
      Afterword and fixes
      as i said before: this is not a tutorial for absolute beginners, albeit it's much easier then most other tutorials, because most is preconfigured in the supplied config.plist. Some Dells have components included, which are not supported by these preconfigured files. Then i can only suggest using Gymnaes tutorial which explains most of the DSDT patching, config.plist editing and kexts used in detail and use the supplied files here as templates.
      Warning: Some people have reported multiple data losses on this machine. I suggest using time-machine whenever possible! If your device is detected as "Model Name: Apple Device", see: http://www.insanelymac.com/forum/topic/319764-guide-dell-xps-15-9550-sierra-10122-quick-installation/page-13?do=findComment&comment=2362337 If you want to save the settings of the display brightness: downgrade to clover 3899, in the never versions the nvram restore is broken. USBInjectAll is not intended for permanent use. You should check which USB are really required to be injected and modify your DSDT/SSDT. 4K Touchscreen only: Multitouch can be achieved with the driver from touch-base.com, but it's not open source - costs > 100 $ Not a bug: if you REALLY want to use the 4K Display natively and disable the Retina Mode (max 1920x1080), see: http://www.everymac.com/systems/apple/macbook_pro/macbook-pro-retina-display-faq/macbook-pro-retina-display-hack-to-run-native-resolution.html Tutorial Updates
      27. March 2017: UHD Kexts added, replaces perl command 23. March 2017: 4k sector tutorial against NVMe corruption added   7. March 2017: Suggestion to disable the SD Card Reader for reduced power consumption 4. February 2017: Dell SMBIOS Truncation workaround added 23. January 2017: Hynix SSD fix added 31. December 2016: USB-C Hotplug Fix and USB InjectAll Removed 28. December 2016: NVMe SSDT Spoof precreated, FakeID already preset in installation config.plist. VoodooHDA added as alternative to SSDT-ALC298 patch as well as color coding in tutorial 22. December 2016: FakeSMBios added Accessories Appendix:
      The official Dell adaptor DA200 (http://accessories.euro.dell.com/sna/productdetail.aspx?c=at&l=de&s=dhs&cs=atdhs1&sku=470-abry) works completly on Sierra 10.2.2. You can use the Network, USB, HDMI and VGA. Everything is Hot-Pluggable a cheap 3rd party noname USB-C -> VGA adaptor didnt work you can charge the Dell with a generic USB-C Power Adaptor, but USB-C has only a maximum power of 100W, so it's either charging OR usage, not both. Dont forget you need a special USB-C cable (Power Delivery 3.0) for charging.
    • By BALDY_MAN
      I've just got my hack. to were I'm happy with it.
      its been a long road. and up to this point was always evolving. and from the software side. id Like to thank EVERYONE that as given there time help and support  in my Hackintosh adventure.
      the hardware side. as at times been a bit of a challenge (learning to bent stainless tubing) I got the powder coating done by a local company
      Please comment. Had to change the tubing around 
                                                                            Best regards 
                                                                                             Baldy
       












    • By glasgood
      GLASGOOD'S
       
      MOJAVE HACKINTOSH GUIDE 
       

       
       
       
      **FOR**  GIGABYTE Z390 AORUS PRO
       
       
       
       
      CREDITS & THANKS
       
      @MaLd0n
      His help with EFI configuration and DSDT
       
      CLOVER  TEAM
      Slice, Kabyl, usr-sse2, jadran, Blackosx, dmazar, STLVNUB, pcj, apianti, JrCs, pene, FrodoKenny, skoczy, ycr.ru, Oscar09, xsmile, SoThOr, rehabman, Download-Fritz, Zenit432, cecekpawon Et al
       
      APPLEALC
      Acidanthera, vit9696
       
      VOODOOHDA
      autumnrain, slice2009, zenith432
       
      ESP PRO MOUNTER
      @Micky1979 
       
      HACKINTOOL
      @headkaze
       
      CLOVER CONFIGURATOR
      Mackie100
       
      THEME ENGINE
      Alex Zielenski
       
      INSANELYMAC
      OLARILA
       
      Hackintool Tutorial
      daliansky
       
      Hackintosh Vanilla Desktop Guide
      /r/Hackintosh - corpnewt
       
       
      MONITORCONTROL
      JoniVR & theOneyouseek
       
       
       
      ------------------------------------------------------------------------------------------------------------------------------------------------------------
       
      UPDATES
       
       
      ------------------------------------------------------------------------------------------------------------------------------------------------------------
       
       
      PART LIST
       
      • Intel I7 8700 
      • Gigabyte Z390 AORUS PRO
      • Gigabyte AORUS RADEON RX 580 8GB ( connected to monitor with DisplayPort )
       
      • Corsair Vengeance LPX 16GB ( 2 x 8GB ) 2666MHz – CMK16GX4M2A2666C16  In this build, both memory modules are installed in memory slots DDR4_A1  and DDR4_B1 
       
      • Corsair RM650x 80 Plus Gold Power Supply Unit
      • Corsair H100i V2 AIO Hydro/Water RGB LED CPU Cooler
      • Samsung EVO 500GB SSD (2.5) macOS Mojave
      • Samsung EVO 250 GB SSD (2.5) Windows 10 Pro
      • NZXT H500 Mid Tower ATX Case
       
      • RECOMMENDED WIFI CARD → ABWB 802.11AC WI-FI With Bluetooth 4.0 PCI-Express (PCI-E) BCM943602CS  
      OR
      • WIFI and Bluetooth with BCM94331CD with PCI-e adapter (but will require AirportBrcmFixup.kext for AirDrop.. )
       
      ** Avoid Samsung EVO 970 PLUS as Hackintosh has problem with that device **
       
       
      WORKING
       
      • Sound 
      • HDMI Port on AMD RX580 / 590 ( Ensure you disable BIOS CSM if using HDMI on RX580 / RX590 )
      • HDMI Port on Aorus Z390 Motherboard ( Ensure you have correct BIOS settings as per this guide for Intel only)
      • Ethernet Port
      • WiFi
      • SSD Trim
      • USB 3.0 & 2.0 
      • AirDrop
      • iCloud
      • Hardware Acceleration
      • iMessages
      • Facetime
      • Handoff
      • Continuity
       

       

       
       
       

       
       
       
       
       
      PREAMBLE - BEFORE YOU START 
       
      Here detailed, is all the  steps towards building a successful and stable Aorus Pro Z390 Hackintosh, if you are a first time Hackintosher, this guide will have you quickly up and running with the Aorus Pro Z390 Hackintosh. To rule out any problems from the go,
      only have the disc that you plan to install macOS Mojave connected to the Aorus Pro, disconnect any other Windows / Linux or data drives, external drives from your Aorus Pro. Windows / Linux and data drives can be connected after successful installation of macOS Mojave
      If you have more than 16 GB of memory, then install macOS Mojave with just 16GB, you can later add any additional memory. Install memory modules in slots DDR4_A1  and DDR4_B1. This build has the Wi-Fi combo PCI-e card installed in slot PCIEX1_3
      with its 9 pin USB cable attached to motherboard header F_USB2. 
       
      If using the Corsair H100i v2 AIO cooler with USB cable connected to motherboard header F_USB1, you will need to enable hot-patch ( explained in guide ) in config.plist for working sleep, wake from sleep will only work by pressing Power Button.
      However, If not using the Corsair H100i v2  USB cable, then you have wake from sleep using Keyboard / Mouse or Power Button.
      The Corsair USB cable is only required if using Corsair Link software in Windows for custom Fan or LED settings.
       
      Install macOS Mojave on its own physical drive, so do not try and install macOS Mojave onto a free partition on a disc that contains Windows.
      Remove any Thunderbolt cards, Thunderbolt card can be reinserted after installation.  Double check your BIOS settings are the same as this guide. 
       
       
      AMD Vega card's  will work with this guide, but If you plan to use a Sapphire Pulse Vega 56 then please read @AudioGod ==>post  regarding the Sapphire Pulse 56.
       
       
       
      Following are unsupported / problematic
       
      • Intel Optane ( if you have this, remove it before installation of macOS Mojave )
       
      • Samsung EVO Plus drives ( firmware problem with macOS )
       
      • XFX Radeon RX 580
       
      • NVIDIA GTX / RTX not supported in macOS Mojave
       
      • Fenvi T919 Wireless Card, it seems Bluetooth is not working out of box for some users ( Maybe the USB port attached to Fenvi bluetooth is wrongly configured, or the SSDT-UIAC.aml port connector was not configured as Internal, or maybe some other reason )
         Save yourself a headache --->  RECOMMENDED WIFI CARD WORKING OUT OF BOX (OOB)  is ---> ABWB 802.11AC WI-FI With Bluetooth 4.0 PCI-Express (PCI-E) BCM943602CS 
       
       
       
      Q - WILL THIS GUIDE WORK WITH MY NON AORUS Z390 PRO MOTHERBOARD ?
      A - Possibly may work with other Z390 chipset motherboards. See very bottom of page for PRE & POST - INSTALL AORUS X 390 EFI's ( will require USB SSDT fix  )
       
      Q - I notice you have the Aorus Pro Z390 version, will this guide work with Aorus Pro Z390 WiFi version ?
      A - Yes, but onboard Intel / Intel CNVi WIFII /Bluetooth will not work with macOS and you will have to disable HS14 for Bluetooth to function properly on BCM943602CS or BCM94331CD WiFi/Bluetooth Combo cards ( more info at bottom of guide) .
       
       
       
       
       
       
      PART 1 - DOWNLOAD 
       
       
      Download the following:
       
      • CLOVER
       
      • PRE-INSTALL Aorus Pro Z390 EFI - RX580.zip
       
      •  POST-INSTALL Aorus Pro Z390 EFI - RX580.zip
       
       
      //OPENCORE EXPERIMENTAL EFI FOR RX580==> EFI.zip
       
       
       
       
       
       
      // INTEL UHD 630 EFI  Aorus Pro Z390 EFI's below. For those who do not have a Graphics Card Installed in PCIe Slot, requires Initial Display Output BIOS setting to be changed to IGFX  spoiler below!
       
      •  PRE-INSTALL Aorus Pro Z390 EFI - Intel UHD630.zip
       
      •  POST-INSTALL Aorus Pro Z390 EFI - Intel UHD630.zip
       
       
       
       
       
       
      • ESP MOUNTER PRO v1.9
       
      • macOS MOJAVE 
       
      • CLOVER CONFIGURATOR
       
      • EmuVariableUefi-64.efi  ( Used only to initialise iMessages. It then must be removed from Clover drivers64UEFI folder as will cause intermittent memory allocation errors on boot, explained in guide)
       
       
      OPTIONAL DOWNLOADS
       
      • Native Display Brightness with MonitorControl
       
      • VoodooHDA.kext.zip 

      • ThemeEngine 
       
      • Assets.car 
       
       
      // Not really needed but IF no sound on Wake from Sleep then use SSDT-ALC1220 and CodecCommander
      • SSDT-ALC1220.aml  ( Resolves Audio Sound on Wake, place in Clover / ACPI / Patched )
       
      • CodecCommander.kext.zip ( Resolves Audio Sound on Wake, place in Clover / Kexts / Other )
       
       
       
       
      PART 2 - BIOS SETTINGS (version F9 )
       
       
      Here is a list of the BIOS settings that I have used ( Screenshots in spoiler below )
       
      • Enter BIOS → Press F12 → Enter Setup
      • Save & Exit → Load Optimized Defaults
       
      • BIOS → Windows 8/10 Features → Other OS
      • BIOS → CSM Support → Enabled
       
      • Peripherals → Initial Display Output → PCIe 1 Slot
      • Peripherals → Trusted Computing → Security Device Support →  Disable
      • Peripherals → Intel(R)Bios Guard → Intel BIOS Guard Support →  Disable
      • Peripherals → USB Configuration → Legacy USB Support →  Enabled
      • Peripherals → USB Configuration → XHCI Hand-off →  Enabled
      • Peripherals → Network Stack Configuration → Network Stack →  Disabled
      • Peripherals → SATA And RST Configuration → SATA Mode Selection →  AHCI
       
      • Chipset → Vt-d → Disabled
      • Chipset → Internal Graphics → Enabled
      • Chipset → DVMT Pre-Allocated → 256M
      • Chipset → DVMT Total Gfx Mem → MAX 
      • Chipset → Audio Controller → Enabled
      • Chipset → Above 4G Decoding → Disabled 
       
      • Power → Platform Power Management → Disabled ( Change to enabled after macOS is installed )
      • Power → ErP → Disabled  ( Can be enabled if you have RGB lighting that you want to power off when shutting down Hackintosh. Thanks @AudioGod for flagging this up)
      • Power → RC6 (Render Standby) → Disabled
       
       
      • MIT → Advanced Memory Settings  → Extreme Memory Profile (X.M.P) → Disabled
      // IF USING  CORSAIR H100i V2 AIO CPU WATER COOLER 
      • MIT → Smart Fan 5 Settings → CPU Fan Control mode → PWM 
       
      • Save & Exit → Save & Exit Setup
       
      SCREEN DUMP SPOILERS
       
       
       
       
       
      PART 3 – CREATE A MOJAVE USB FLASH INSTALLER
       
      Prepare USB Installer for Mojave ( Video below )
       
      • Insert USB drive
      • Launch /Applications/Utilities/Disk Utility
      • Disk Utility → View → Show All Devices
      • On Left-hand panel → External →(Identify your USB device in left hand panel)
      • Click and highlight your USB device in the left-hand panel.
      • Click erase button.
      • Name: USB
      • Format: Mac OS Extended (Journaled )
      • Scheme: GUID Partition Map
      • Click Erase button.
       
      • Place the downloaded MacOS Mojave app into Applications folder.
      • Open Terminal copy and paste:
       
      sudo /Applications/Install\ macOS\ Mojave.app/Contents/Resources/createinstallmedia --volume /Volumes/USB --nointeraction && say Mojave Drive Created  • Enter
       
       
       
       
       
       
       
       
       
       
       
      PART 4 – INSTALL CLOVER ON THE MOJAVE USB INSTALLER 
       
      Make Mojave USB flash drive installer bootable.( Video below )
       
      • Launch Clover application, double click.
      • Click Continue → Continue → Continue 
      • Click Change Install Location button.
      • Click Install macOSMojave USB installer → Continue
      • Click Customise button
      • Choose:
      Clover for UEFI booting only Install Clover in the ESP Themes UEFI Drivers • Click Install button
      • Installation Complete!
       
      Video:
       
       
       
       
       
       
      PART 5 – CUSTOMIZE MOJAVE USB INSTALLER FOR AORUS Z390 PRO
       
      Replace Clover EFI folder with PRE-INSTALL Aorus Pro Z390 EFI - RX580.zip  OR  if NO graphics card installed in PCIe slot, then use PRE-INSTALL Aorus Pro Z390 EFI - Intel UHD630.zip( Video below ) 
       
      • Install ESP Mounter Pro v1.9
      • Using ESP Mounter Pro, Mount ESP on disk2s1 ( Your disk name may be different )
       

       

       
       
       
      • Open mounted EFI partition found on desktop
      • Copy all the contents from Aorus 390 Pro EFI folder
      • Replace USB EFI folder with all the contents inside the Aorus 390 Pro EFI folder.
       
       

       
       
       
       
       
       
       
      PART 6 – INSTALL MAC OS MOJAVE ON INTERNAL DRIVE
       
      INSTALL NOTE
       
      ENSURE BIOS: Above 4G Decoding is set to Disabled 
      if Above 4G decoding is set to enabled then macOS Mojave install will freeze at 2 mins remaining and will not shut down properly!!!!
       
      Please be patient during install, so when install gets to 2 or 3 mins remaining then it may take extra time. Be ready to boot from UEFI USB installer by pressing F12 when install initiates restarts. 

      • INSERT USB INSTALLER INTO THE USB 2.0 PORT  
       
       
       Here is a walkthrough of the full process using the macOS Mojave USB Installer on the Aorus Z390 Pro. 
       
       
       
       
      • Power on PC and press F12• Choose bootable USB drive from boot menu.
       
       
       
      • Install macOS Mojave to internal solid state or hard drive.
       
       
       
      When system returns to the Clover boot menu choose:
       
      • Boot macOS Install from Macintosh
       
       
       
      At next restart, press F12 and boot from external UEFI USB device and choose:
       
      • Boot macOS Install from Macintosh
       
       
       
      Proceed with macOS Mojave install
       
       
      macOS Mojave is now installed, but it can only boot at this moment thanks to FakeSMC and Clover on the Mojave USB flash drive installer.
       

       
       
       
       
       
       
      PART 7 – MAKE AORUS Z390 PRO INTERNAL DRIVE BOOTABLE
       
      Make internal drive bootable ( Video below )
       
      So far, the Aorus Pro can only boot the internal system drive with the aid of the Mojave USB Installer.
      To boot from the internal system drive without the installer: 
       
      Download and install Clover with RC Scripts on target volume.  
      If your Aorus Pro Z390 has AMD RX 580 then copy the EFI folder from inside POST-INSTALL Aorus Pro Z390 EFI - RX580.zip  folder and paste it inside the the System Drive EFI partition.          OR
      If your Aorus Pro Z390 has no graphics card installed in PCIe slot, then copy the EFI folder from inside POST-INSTALL Aorus Pro Z390 EFI - Intel UHD630.zip  folder and paste it inside the the System Drive EFI partition.   
       

       
       
       
      • Remove USB Mojave installer and shut down and restart.
       
      Aorus Hackintosh should now be able to boot to macOS Mojave, Done, well almost ! 
       
       
       
       
       
      PART 8 – ENABLE IMESSAGES & FACETIME 
       
       
      // UPDATE 21st MAY 2019
       
      Possibly Clover Configurator now automatically populates correct values for working iMessages when you select an SMBIOS.  
       

       
      After selecting SMBIOS, example iMac19,1 for Aorus Pro with RX580 ( image above ) then go to Apple and ensure you have the "serial number is not valid " message. Done!
       
      If you still have problems connecting to iMessage, test and ensure that AirDrop is working, then follow instructions inside spoiler. 

       
       
      • Mount internal drive EFI/ESP partition
      • Go to folder CLOVER → drivers64UEFI 
      • Place both EMUVariableUefi-64.efi inside → drivers64UEFI
       
       
      Using Clover Configurator, add the following argument to config.plist using Clover Configurator.
       
      • Slide = 0
       

       
       
      Shutdown and then press power on button on PC.
       
      • You should now be able to Log into iCloud, iMessages and FaceTime
       
       
       
      • NOW delete EMUVariableUefi-64.efi from CLOVER → drivers64UEFI Folder 
      • Shutdown and restart Aorus Pro hackintosh. iMessages etc is now operational without EMUVariableUefi-64.efi ( EMUVariableUefi-64.efi only needed to initialise iMessages )
       
       
      // UPDATE 22nd May 2019 
       
      • It seems that there are no "Couldn't allocate runtime area"  errors when continuing to use EMUVariableUefi-64.efi since updating to macOS Mojave 10.14.5 and using Clover version r4920. 
      • It is important to delete EMUVariableUefi-64.efi, this will avoid very intermittent boot errors such as: “Couldn’t allocate runtime area”  post errors.
       
       
       
       
      PART 9 – ENABLE TRIM for Solid State Flash Drives
       
      Open Terminal and enter the following command:
      sudo trimforce enable  
       
       
       
       
      DEFAULT SSDT –  USB PORTS FIX CONFIGURATION WITH FRONT USB-C - SSDT USBPorts.kext ALREADY INSIDE AORUS Z390 EFI FOLDER  – Provided by @AudioGod  
       
       

       

       
      If you have USBC on Computer Chassis / Case, then SS01 and SS02 is mapped to that USB C port 
       

       
       
       
       
       
       
      ------------    GUIDE FINISHED YOU SHOULD NOW HAVE WORKING AORUS Z390 PRO HACKINTOSH  WITH SSDT USB FIX   ------------
       
       
       
      OPTIONAL: Set Wi-Fi Country Code
       
       
       
       
       
       
      OPTIONAL: System Information - PCI
       
       
       
       
       
       
       
      External USB Storage:  Fix "disk did not eject properly" message upon wake from sleep
       
       
       
       
       
       
       
      OPTIONAL:  Native Display Brightness - with MonitorControl

       
       
       
       
       
       
      OPTIONAL:  Dual Boot macOS Mojave & Windows 10 
       
       
       
       
       
       
       
       
      OPTIONAL:  Replace the default "About This Mac" Apple Logo with RED AORUS APPLE
       
       

       
       
       
       
      OPTIONAL - ALTERNATIVE SSDT 1 –  SSDT Ports configuration below - replace SSDT inside Clover /ACPI/PATCHED folder 
       
       
       
       
       

      OPTIONAL - ALTERNATIVE SSDT 2 -  SSDT Ports configuration below - replace SSDT inside Clover /ACPI/PATCHED folder 
       
       
       
       
       

      OPTIONAL - ALTERNATIVE SSDT 3 – Create your own SSDT
       
       
       
       
       
      FRAMEBUFFER PATCHING  – For working Intel UHD 630 Graphics, working HDMI Port, working HDMI Audio on Aorus Z390 Pro
       


       
       
       
       
       
       
      FINAL CUT PRO  – Configuration for AMD RX5xx 
       
       
       
       
      AORUS PRO Z390 WIFI version with Intel CNVi  – Disable Bluetooth on HS14
       
      Resolve bluetooth issue  reported by @eSaF 
       
       
       
       
       
       
      CLOVER  – Updating / Upgrade Clover boot loader 
       
       
       
       
       
       
      SLEEP  – Sleep and Automatic Sleep

       
       
       
       
       
       
       
       
      SLEEP  – Resolving Instant Wake ( Corsair H100i v2 AIO )
       
       
       
       
       
       
       
       
      WIFI  – Clover Hotpatch PXSX to ARPT
       
       
       
       
       
       
       
       
       
       
      RECOMMENDED READING  – Excellent Hackintosh Vanilla guide created by CorpNewt with in depth tutorial on Clover.  
       
      https://hackintosh.gitbook.io/-r-hackintosh-vanilla-desktop-guide/config.plist-per-hardware/coffee-lake
       
       
       
       
       
       
       
       
       
      AORUS Z390 MOTHERBOARD X  – EFI WITH NO USB SSDT, WITH PORTS LIMIT PATCH, WITH SSDT-GPRW SLEEP / WAKE FIX
       
      Q - I notice you have the Aorus Pro Z390 version, will this guide work with other Gigabyte Aorus Z390  motherboards ?
      A - Possibly, but it is not guaranteed that these EFI folders below may work. 
       
       
      PRE-INSTALL Aorus X Z390 EFI - RX580.zip
      POST-INSTALL Aorus X Z390 EFI - RX580.zip
       
      PRE-INSTALL Aorus X Z390 EFI - Intel UHD630.zip
      POST-INSTALL Aorus X Z390 EFI - Intel UHD630.zip
       
       
       
       
       
       
       
       
       
       
       
       

       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
      SSDT-UIAC.aml.zip
      SSDT-UIAC.dsl.zip
       
      CodecCommander.kext.zip
      SSDT-ALC1220.aml.zip
       
       
    • By Amit Meena
      This card is working OOB, but it has some graphical issues as per attachments.

      If someone has a solution please share.






×