Jump to content
MaLd0n

High Sierra on Supermicro X10DAI / Dual Xeon E5-2690V4 / DSDT

191 posts in this topic

Recommended Posts

21 hours ago, MaLd0n said:

try with MacPro6,1 smbios, press O clover boot screen and change in smbios section

Identical kernel panic using MacPro6,1

Share this post


Link to post
Share on other sites
Advertisement
1 hour ago, schrodinger said:

Identical kernel panic using MacPro6,1

send me ur clover folder inside usb stick

Share this post


Link to post
Share on other sites
3 hours ago, MaLd0n said:

send me ur clover folder inside usb stick

Here you go. Thanks for the help! If we can get this working 100% I'll donate much more.

CLOVER.zip

Share this post


Link to post
Share on other sites
58 minutes ago, schrodinger said:

Here you go. Thanks for the help! If we can get this working 100% I'll donate much more.

CLOVER.zip

a default config for ur chipset, try

EFI.zip

Share this post


Link to post
Share on other sites
4 hours ago, schrodinger said:

Just replace files in installer?

replace full efi

Share this post


Link to post
Share on other sites
46 minutes ago, MaLd0n said:

replace full efi

 

OK! Mounted EFI partition under High Sierra using:

diskutil list

sudo diskutil mount /dev/disk11s1

Where disk11 was the device and s1 pointed to the EFI partition. I then replaced the files completely. Got the panic screen below.

IMG_4296.JPG

Share this post


Link to post
Share on other sites

Blowing off the dust on this one but think anyone could give me a hand with an X10DRH? I got it mostly up and running but I had to drop the custom DSDT posted on this tread. Curious if someone could perhaps make a custom one (or know if there is one that I couldnt find. Thanks!

Share this post


Link to post
Share on other sites
45 minutes ago, Dasoslukos said:

Blowing off the dust on this one but think anyone could give me a hand with an X10DRH? I got it mostly up and running but I had to drop the custom DSDT posted on this tread. Curious if someone could perhaps make a custom one (or know if there is one that I couldnt find. Thanks!

drop edited dsdt(is not for ur mobo) and extract one send_me

--Run_Me
RunMe.app
https://www.youtube.com/watch?v=k9wmIfGLe3A

Share this post


Link to post
Share on other sites
1 hour ago, MaLd0n said:

try without "kernel to patches" patches

Rodger that, little confused though. Is that clover boot option or an install option? (excuse my ignorance, first time getting back into the scene in many, many years lol)

Share this post


Link to post
Share on other sites
17 hours ago, MaLd0n said:

try without "kernel to patches" patches

Okay, derp, I figured what you meant (i think at least). So I booted without injecting any kexts. The system hangs here for a while then reboots.

 

image0.thumb.jpeg.dbd725dfaf15424fc759c224c1c5cc51.jpeg

image0 2.jpeg

Share this post


Link to post
Share on other sites
1 hour ago, Dasoslukos said:

Okay, derp, I figured what you meant (i think at least). So I booted without injecting any kexts. The system hangs here for a while then reboots.

smc emulate is mandatory for all hacks

 

use fakesmc or virtualsmc

Share this post


Link to post
Share on other sites
24 minutes ago, MaLd0n said:

smc emulate is mandatory for all hacks

 

use fakesmc or virtualsmc

Makes sense. So booting with injected kexts only with FakeSMC I get this.

image0.jpeg

Share this post


Link to post
Share on other sites

Hello! Thank you for posting this. I have Supermicro X10DAI /

Microprocessor 2 x 3.2 GHz 6-Core Intel Xeon    E5-2643V3 QS

Total Number of Cores: 12

Video Card Nvidia Quadro FX 5600 ( 1536 MB / Nvidia )

hard disk WDC WD5003ABYX-01WERA0 ( 500 GB / 7200  )

 

Apple macOS Mojave 10.14.1 and 10.14.6

1. I used your EFI document to access hard disk tools, it got stuck at final part of disk reformatting process.

2. The last installation got stuck in the last 22 minutes in the second restart, so the installation didnt complete. Hope I can get your help and advice on how to proceed. Please see attached photos. Thanks.

PICT0354.JPG

Share this post


Link to post
Share on other sites

Hello! Thank you for posting this. I have Supermicro X10DAI /

Microprocessor 2 x 3.2 GHz 6-Core Intel Xeon    E5-2643V3 QS

Total Number of Cores: 12

Video Card Nvidia Quadro FX 5600 ( 1536 MB / Nvidia )

hard disk WDC WD5003ABYX-01WERA0 ( 500 GB / 7200  )

 

Apple macOS Mojave 10.14.1 and 10.14.6

1. I used your EFI document to access hard disk tools, it got stuck at final part of disk reformatting process.

2. The last installation got stuck in the last 22 minutes in the second restart, so the installation didnt complete. Hope I can get your help and advice on how to proceed. Please see attached photos. Thanks.

PICT0354.JPG

Share this post


Link to post
Share on other sites
4 hours ago, YangJsheng said:

Hello! Thank you for posting this. I have Supermicro X10DAI /

Microprocessor 2 x 3.2 GHz 6-Core Intel Xeon    E5-2643V3 QS

Total Number of Cores: 12

Video Card Nvidia Quadro FX 5600 ( 1536 MB / Nvidia )

hard disk WDC WD5003ABYX-01WERA0 ( 500 GB / 7200  )

 

Apple macOS Mojave 10.14.1 and 10.14.6

1. I used your EFI document to access hard disk tools, it got stuck at final part of disk reformatting process.

2. The last installation got stuck in the last 22 minutes in the second restart, so the installation didnt complete. Hope I can get your help and advice on how to proceed. Please see attached photos. Thanks.

 

use -v

Share this post


Link to post
Share on other sites

The last installation got stuck in the last 22 minutes in the second restart, so the installation didnt complete. Hope I can get your help and advice on how to proceed. Please see attached photos. Thanks.

WeChatbb12f2ca736a84b97b93e9625e1778b5.png

PICT0010.JPG

Share this post


Link to post
Share on other sites
20 hours ago, YangJsheng said:

The last installation got stuck in the last 22 minutes in the second restart, so the installation didnt complete. Hope I can get your help and advice on how to proceed. Please see attached photos. Thanks.

 

 

send me ur efi folder

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By bilbo
      THE GREAT GUIDE
      HIGH SIERRA + Z820

       
      ********
      10/07/2018
       
       
      *********************************************************************************
      ————————————————————————————————————————
      ————————————————————————————————————————
       
      (from El Capitan's guide)
      (from Sierra's guide)
       
      Introduction:
       
      Hi everybody. 
      Again, a new guide version, updated to High Sierra. I hope it will be useful for you all. This time, the update is easy. Basically, the 100% of Sierra’s guide is still valid for High Sierra. The guide has been updated to update links, kexts versions … etc, and some parts try to be more clear. Just there are some important topic to keep in mind:
       
      1. What's new?.
      There is a new and absolute important setting to install High Sierra. We have to activate “legacy ACPI cpu tables” in Advanced Section, in BIOS. Without this option enabled, we will get a KP. 
      This option changes completely the structure of the SSDT needed for PM. We have to get rid old SSDT versions, if you extracted them with this option disabled. And all SSDT generated by ssdtPRGen, too. And, if your DSDT has the “SSDT-1-CpuDef” code injected, (following my previous guides, to skip "No ACPI Processor declarations found in the DSDT!" error, (see PM section) ) you will have to delete that part, because the DSDT will cause a KP. A better method is described in this guide. No need of add strange code into DSDT.

       
      2.Can I use my old files from Sierra´s EFI folder?
      The most important, yes. You can keep your config.plist and your DSDT(see point N.1) … saving tons of time. You have to use the new drivers64Uefi files installed by new clover version, and update the kexts versions of main kexts. The specific kexts for our dear machine, USB3, Astek driver, remains in same version.Of course, I provide of all links and files (into my stuff folder) in this guide.
       
      3. So, do I Need repeat again every step of this guide?.
      If you comes from Sierra´s guide, no. After 1stboot and graphics divers install, you can use your previous files (see point 1.) reboot and jump directly to PM section. 
      For new users, Yes, sure.

      4. Consider any part of this guide open to discuss.
      If you see something wrong, or which could be improved, please, just say it, and I’ll fix it. English is not my native language. If you can’t understand some step, or something could be best written, please, just say it and I’ll fix it too
       

      FOR 26x7 and 26x3 USERS!!!. Finally, there a Fix to this models. It´s under test, but I think it should work. Check out FIRST the last section of this guide.
       
      5. And please, (this is for "anonymous" users) don't PM me with personalquestions. No need for that.Any question can be answered openly.
       
       
      Ok, let’s go.
       
       
       
      PART I
       
      1-BIOS SETUP
       
       
      This guide is for UEFI systems. This is not important to follow this guide except in Clover installation section. Keep in mind it to adapt some settings if you need use legacy-bios mode. 
       
      If you don’t need any special option, and you have been playing with options, reset the bios to default settings.Later, you will be able to change and test, if you need some specific option. The next section describe the essential options. 
       
      6. The main BIOS options are:
       
      In storage: 
      set ACHI mode (IMPORTANT).
       

       
       
      Set boot order. UEFI first, (for me), USB first and HD second. 
       


       
      Security : 
      Device Security: I like disable unused devices (scu controller and serial port). Optional.



       
      Disable Vt-d: Disabled. IMPORTANT. 
       

       

       
      Secure boot. Disabled (...to boot with non signed OS). 
      I use UEFI boot, but I keep legacy support active. This is optional.
       

       
       
      In Power :
      Set Runtimepower management to Enabled. This option will allow Power Management later. About the rest of options, I’m not sure of the impact in performance. Set them by default by the moment. Not important for the guide. Only remeber for further tests that with Pcie Performance Mode enabled, power boost is disabled. Idle Power Savings manage sleep policies.


       
       
      In Advanced:
       
      Set PXE, Storage and Video to EFI. (for me) , or legacy, as your want. If you have a graphic card non EFI-compliant, you can set video in Legacy, keeping an UEFI boot.
      Don’t forget set thunderbolt policy in Legacy mode.
       

       

       
      And Now, the essential setting for High Sierra: 
       
      -Enable “Legacy ACPI CPU Tables”
       


       

       

      _________________________________________________________________________________________________________________________________
       
       
       
      PART II:
       
      INSTALLATION
       
      7- MEDIA CREATION
       
      (This guide assume you have a MacOs running. I have no idea how do it on PC)
       
      -Important: Download HighSierra dmg only from Apple.Don´t use suspicious dmgs or Isos. It’s not longer available to search in Apple Store, since Mojave release. Go to this link, and click in “Get macOS high Sierra” (at mid of the page). It will open the apple store download link. The dmg is downloaded in /Applications folder. Let the file in Applications folder. (and keep one compressed copy for future attempts)

       
      -Format one USB stick with common settings:
       


       
      Go to erase tab, select GUID partition table in options, and Mac Os Extended (Journaled) as Filesystem. Name the partition as “USB”. Ok to Apply.   
      On a terminal window, type (copy and paste) :  
      sudo /Applications/Install\ macOS\ High\ Sierra.app/Contents/Resources/createinstallmedia --volume /Volumes/USB --applicationpath /Applications/Install\ macOS\ High\ Sierra.app --nointeraction  
      Enter and type your admin password. It will take 10-15 minutes. (When it finish, you’ll see the prompt again)  
      8. INSTALLING CLOVER.
       
      -Download Clover from here. Version used to make this guide: Clover_v2.4k_r4658.
      -Download Clover Configurator from here. It makes easier edit config.plist file and we can use a lot of clover features easily. Now there is a “global edition”
      -Download plisteditor pro demo for edit info.plist files.
      -Download my High Sierra stuff folder. (at the end of the guide)
      -Additional tools: One tool for install kexts, fix permission and rebuild cache. I use Kext helper from rampage’s dmg, although I need always force quit. I don´t like the rest of utilities. This is a personal option. Also you can download  EFI mounter (from download sections of this site). CloverConfigurator mounts EFI too, but maybe with this utility is easier.
       
      -Install Clover in the USB. On first screen, don’t forget change the install location in order to do not install on your Internal HD. Select your USB stick.
      Click on Customize. Choose “Install for UEFI booting only” and “Install Clover in the ESP” as main options (if your system is UEFI-based) This is optional: choose your favorite Theme. In Drivers64UEFI select: Now is longer section. It´s only because is more exact showing the drivers installed. We have to keep selected the default options and add the same additional drivers. Keep in mind two important things:                   -There is a new driver, APFS driver, for the “new” filesystem. This driver is now essential, in order to allow clover “see” HDs formatted with this FS. It´s activated by default. 
                       -The OSxAptiopnFix2Drv has a new version, v3.
                ... The conclusion of this long explanation, is that we have to add to the default selection of drivers: 
       
                                - EmuVariableUefi-64
                               - OsxAptionFix3Drv
       

      Let the rest of option unselected and Click on Install.
       
       
      9- CONFIGURE CLOVER

      When clover finishes, it will mount EFI partition. Time to modify it. You’ll find all necessary files in my folder. There are three things to modify: config.plist, drivers, and kexts
       
      9.1 Config.plist
       
      The default config.plist is not useful for us. Replace it by mine (folder n.2)
      But take a look to options (with clover configurator) to understand my options in order to be able to adapt them for your specs or your preferences. It’s a basic config.plist. I could add more options or fixes. but is a good idea install with minimum options. 
       
           Acpi section.
          All fixes in ACPI section has been removed except some minor fixes in 2 subsection, smart ups option, etc. SmartUps it’s not important now, but it will be later. So I prefer activate this option. 
          The most important, The rename usb devices patches are included. 
       
          

          Boot section
          Bootflags needed are only -v and npci=0x2000. Of course -v is optional only to see the boot process. You can deactivate it when you finish.
       
          
       
          Any option activated in Boot Graphics/ Cpu/Device/Disable driver
       
          Gui options. These are only personal preferences.
       
          
       
          Graphics. AnyGraphic injection annd any option activated. At least, no needed for my 1080ti card. Check it out for your card video.
       
          
       
          An essential section. Kernels Patches needed.
       
          
       
          RT Variables. BooterConfig, and Csr to deactivate security policy in Sierra. The info values are taken from smbios.
       
          
       
          SMBIOS.  Set it to Mac Pro 6,1. 
       
          
       
                    IMPORTANT—>press “generate new” repeatedly to get one random fresh serial number
       
          System parameter: 
       
          
       
       
      9.2 -Drivers64UEFI folder.
       
      As usual, delete VBoxHfs-64driver and replace it by HFSPlus.efi. (from my folder).

           
       
       
      9.3 Kexts folder:
       
      Add my Kexts from my stuff to /EFI/CLOVER/Kexts/10.13
       
      They are:

           
       
      These are the versions Updated since Sierra´s guide.
       
      FakeSMC.kext. If you remember, I have some unexpected KP due to fake smc sensors. Well, I have searched a bit about this, and testing. The main topic is keep the fake smc version and sensors kext of same version or branch. There are several branchs developing              different versions (slice, rehabman, kozleck, etc), after test, and test, I think the most stables and those which gives me best sensor readings is kozeck version. I attach the v1440 from kozleck. In this step I only use FakeSMC kext, withput sensors kexts. Anyway, if you have a better version, use it. Just, don´t forget no use the sensors Kexts.   
      VoodooTSCync.kext, to avoid boot with -x (from rampagdev, dual cpu dmg). You’ll find several versions into my folder.I haven’t noticed any change using the generic or the specific version. I think that is not important for our platform.                  The customize method is:

       

       
               Anyway, I provided the generic version and customized versions for every cpu.

       
      IntelMausiEthernet.kext . Kext for the ethernet card from rehabman. (2018-0424version). It will allow have internet connection on first boot.  AppleIntelE1000e.kext. Kext for ethernet card from here (2017-10-18 version). (Change of  server if you have problems downloading) <<<< update. Use this better than IntelMausiEthernet.kext
       
      UsbInjectall, for USB2 from rehabman( 2018-0822version)  
      And add to /EFI/CLOVER/Kexts/others
       
       

       
       
      Lilu kext (from here, 1.2.7version) NOTE: The kext for download is available in " LILU-X.X.X-RELEASE.zip" link  
      WhateverGreen.kext (from here, 1.2.2 version) old NvidiaGraphicsFixup proyect has been integrated into this proyect. It's useful for nvidia and amd graphics cards.  NOTE: The kext for download is available in " WhateverGreen-X.X.X-RELEASE.zip" link  
      This couple of kexts avoid black screen booting with 6,1 smbios. Is quite important keep in mind the versions of these kexts keeping the right versions among this kexts. Prior to update some of them, you have to check in original websites if it's is compatible with the rest. These versions are ready to work with 10.13.6. 
       
      Thats all. We have our usb installer ready. Copy in a folder all stuff necessary to repeat the process and copy it to the USB stick. You will have it available after first boot.
       
      Reboot from the USB stick and install High Sierra. 

       
      10- INSTALLATION

       
      Some advices:
           -Use only USB2 ports, preferably the front USB2 port.
           -Don’t use USB hubs, or cable extenders… (personal issues)
           -Unplug any other usb device
           -Be sure that you have plugged your internal sata drive to one of the two internal achi sata controller.
       

       
           -The boot process may be slow, (and with terrible and apocalyptic errors). Be patient
           -Maybe, the boot stucks with the error “consideredRebuildKernel …. blabla”. Just reboot again.
           -If you have two monitors, shutdown one can help with graphical errors.
           -Plug your graphic card in PCI Slot 2.
           -For inexperienced users: On first screen, go to disk utility and erase the Volume. (APFS and GPT). Quit the utility and return to first screen. Choose Install.
           -The process is splitted in two steps. The first step promises take only 4 or 5minutes … and now, it’s true!!!. It will take4 or 5 minutes(with a SSD).
           -After this first reboot, in clover boot screen, you will see more partitions than expected. APFS file system manage more partitions in a more complex way (physical layer, logical layer… bla, bla). Select  the new internal HighSierra boot installer partition, not the usb installer. It will finish the  process. This step, takes 10-15min aprox (using a SSD).
       
      Note.I had some unexpected reboot in this step. Only re-trying if you have it also.
       
      -To boot again after installation, keep booting from USB , ant then choose internal HD as clover boot screen.
       
       
      ---------------------------------------------------------------------------------------------------------------------------------
       
       
       
      PART III:
       
      FIRST BOOT
       
      11. Optional updates.
      Finally, we are on High Sierra's Dektop. The Mac os Version is 17G65. In the date of this guide (oct/2018) is the last version. (there is an optional update only for real macbook laptops). For future security updates, this is the moment to update. Set up the internet options and update the system, but remember check if the Lilu and whatevergreen kexts are compatible or if you need use a new version, or you will geta KP or a black screen on boot. Update using the update app, reboot, and wait for the update installation.
       
      12- Install Clover.
      On first reboot, install clover again on HDD, repeating same process and same options than with the USB installer, but keep in mind you have to add some options on clover’s screen install:
       


       

           -Install RC scripts on target volume
           -Optional RC scripts
           -Install Clover Preference Panel.

      …and install clovermanager.app. This is optional but it’s the best way to manage the themes and find a good theme. I provide of one nice High Sierra Theme and the Bootcamp theme. Of course, left this for later. 
       
      Install clover and add same files used on the USB: config.plist , hfsplus driver and kexts. Reboot. You can now extract the USB installer and reboot from the internal HDD.
      After boot, go to clover preference panel and set it to auto mount EFI partition. It will be useful along this process. Disable this when you finish and you get stable your system.
       
       
    • By MaLd0n
      Now have a Olarila app, just download app and clover folder for your Chipset! https://olarila.com/forum/viewtopic.php?f=81&amp;t=6771   Nehalem, SandyBridge, IvyBridge, Haswell, Broadwell     Skylake, Kabylake and Coffeelake is here http://www.insanelymac.com/forum/topic/321872-guide-sierra-on-gigabyte-mobos-serie-200-kabylake-dsdt/   Install MacOS with Olarila Image, Step by Step, Install and Post Install
       
      https://olarila.com/forum/viewtopic.php?f=50&t=8685
        Mojave Full DSDT patch   http://olarila.com/forum/viewtopic.php?f=59&amp;t=6428   First...   ***Update bios to last available version!***   If you need a full patched DSDT...  -Extract tables with F4 key in Clover boot screen! -Run it and send me files! RunMe.app   Installation   --Create a bootable copy of macOS Sierra / High Sierra / Mojave   https://github.com/chris1111/Create-Install-Media/releases   --Install Clover in USB stick   https://sourceforge.net/projects/cloverefiboot/files/Installer/   --Replace with my Clover folder https://olarila.com/files/Clover.Folder/CLOVER.SERIES.CHIPSET.zip   --Install Sierra/High Sierra and boot into system!   Post Installation --Install Clover and replace with my folder   https://olarila.com/forum/viewtopic.php?f=28&t=8222   --Reboot and activate video!   Bingo!   Now you need a fine tune! DSDT time!   --DSDT   Patches -FIX ERRORS AND WARNINGS -HPET -SATA -DMAC -SLPB -DARWIN -LPC -XHCI -PLUGIN TYPE -XXXX to HDEF -HDEF -RTC -IRQs -SBUS -BUS1 -MCHC -ALS0 -SHUTDOWN -LAN -USBX -PMCR -EC -PNLF -HDMI
       
      --Power Management
      - 1 Generation Intel Processors, use Generate P and C States in config.plist
      - 2 and 3 Generations Intel Processors, Generate SSDT with Piker script and drop CpuPm and Cpu0Ist SSDTs
      ssdtPRGen.command.zip
      Credits-https://github.com/Piker-Alpha/ssdtPRGen.sh
      - 4 Generation+ Intel Processors, use PluginType=1 in DSDT, SSDT or Clover config.plist
       
      for check Power, Frequency, Temperature and Utilization, use it
       
      Install Intel Power Gadget.pkg.zip
       
      --Brightness
      Install .app, select the required permission and reboot. Work in F1 / F2 keys!
      NativeDisplayBrightness.app.zip


      https://github.com/Bensge/NativeDisplayBrightness/releases
      *in some cases .app don't work, check patches in config.plist inside Clover folder Post Install
       
      --Clover
       
      https://sourceforge.net/projects/cloverefiboot/files/Installer/
       
      --AUDIO
       
      Use DSDT + AppleAlc
       
      --install Lan driver by Mieze
        -Atheros   http://www.insanelymac.com/forum/files/file/313-atherose2200ethernet/   -Intel   http://www.insanelymac.com/forum/files/file/396-intelmausiethernet/   -Realtek   http://www.insanelymac.com/forum/files/file/88-realtekrtl8111-binary/   --Links   -FakeSMC   https://bitbucket.org/RehabMan/os-x-fakesmc-kozlek   -Audio   https://github.com/vit9696/AppleALC http://www.insanelymac.com/forum/topic/314406-voodoohda-289/   -USB   https://bitbucket.org/RehabMan/os-x-usb-inject-all/downloads   It's time to Rock   -Credits and thanks to the old and new people in the community who developed patches, kexts and bootloaders!   Apple, Slice, Kabyl, usr-sse2, jadran, Blackosx, dmazar, STLVNUB, pcj, apianti, JrCs, pene, FrodoKenny, skoczy, ycr.ru, Oscar09, xsmile, SoThOr, RehabMan, Download-Fritz, Zenit432, cecekpawon, Intel, Oracle, Chameleon Team, crazybirdy, Mieze, Mirone, Oldnapalm, netkas, Elconiglio, artut-pt, ErmaC, Pavo, Toleda, Master Chief and family, bcc9, The King, PMheart, Sherlocks, Micky1979, vit9696, vandroiy2013, Voodoo Team, Pike R. Alpha, lvs1974, Austere.J, CVad and many, many, many others!   We're all here to have fun and learn from each other!  
    • By MaLd0n
      Now have a Olarila app, just download app and clover folder for your Chipset! https://olarila.com/forum/viewtopic.php?f=81&amp;t=6771   Install MacOS with Olarila Image, Step by Step, Install and Post Install
       
      https://olarila.com/forum/viewtopic.php?f=50&t=8685
        First... If you need DSDT edits... -Extract tables with F4 key in Clover boot screen! -Run it and send me files! RunMe.app   Installation --Create a bootable copy of El Capitan /  Sierra / High Sierra / Mojave   https://github.com/chris1111/Create-Install-Media/releases   --Install Clover in USB stick https://sourceforge.net/projects/cloverefiboot/files/Installer/   --Replace with my Clover folder   https://olarila.com/files/Clover.Folder/CLOVER.LGA775.zip   --Install EL Capitan / Sierra / High Sierra and boot into system!     Post Installation   --Install Clover and replace with my folder   https://olarila.com/forum/viewtopic.php?f=28&t=8222     --Reboot and activate video!   Bingo! Now you need a fine tune! DSDT Time!   My DSDT GA P35-DS3   DSDT.MaLd0n.zip     Patches -FIX ERRORS AND WARNINGS -HPET -SATA -SLPB -DARWIN -LPC -HDEF -RTC -EHCI -UHCI -IRQs -SBUS -BUS1 -MCHC -ALS0 -SHUTDOWN -LAN -EC -PNLF --Native Power Management
       
      Use Clover, check Generate P and C States
       
      --Brightness
      Install .app, select the required permission and reboot. Work in F1 / F2 keys!
      NativeDisplayBrightness.app.zip


      https://github.com/Bensge/NativeDisplayBrightness/releases
      *in some cases .app don't work, check patches in config.plist inside Clover folder Post Install
       
      --AUDIO
       
      Device HDEF + AppleAlc + Lilu
       
      --install Lan driver by Mieze
        -Atheros   http://www.insanelymac.com/forum/files/file/313-atherose2200ethernet/   -Intel   http://www.insanelymac.com/forum/files/file/396-intelmausiethernet/   -Realtek   http://www.insanelymac.com/forum/files/file/88-realtekrtl8111-binary/   --Links   -FakeSMC   https://bitbucket.org/RehabMan/os-x-fakesmc-kozlek   -Audio   https://github.com/vit9696/AppleALC http://www.insanelymac.com/forum/topic/293863-applehda-patch-requests/   -Credits and thanks to the old and new people in the community who developed patches, kexts and bootloaders!   Slice, Kabyl, usr-sse2, jadran, Blackosx, dmazar, STLVNUB, pcj, apianti, JrCs, pene, FrodoKenny, skoczy, ycr.ru, Oscar09, xsmile, SoThOr, RehabMan, Download-Fritz, Zenit432, cecekpawon, Intel, Apple, Oracle, Chameleon Team, crazybirdy, Mieze, Mirone, Oldnapalm, netkas, Elconiglio, artut-pt, ErmaC, Pavo, Toleda, Master Chief and family, bcc9, The King, PMheart, Sherlocks, Micky1979, vit9696, vandroiy2013, Voodoo Team, Pike R. Alpha, lvs1974, Austere.J, CVad and many, many, many others!   We're all here to have fun and learn from each other!   ENJOY!  
    • By kylon
      ACPI and Clover config for Acer Aspire v5-571PG
       
      Tested on Catalina 10.15.1 and Clover EFI 5098 (Should work on MacOS 10.9.x - 10.15.x)
       
      Not Working:
      - sd card reader
      - Atheros AR9462 (use a compatible USB wireless adapter, see below)
      - Touchscreen (MacOS 10.15 only)
       
       
      Notes:
      Disable Secure Boot and enable Legacy Boot. Legacy Mode is recommended.  
      **To reset your BIOS, power on the pc and hold the power button for about 30-40 seconds or you can short G2101 (RAM SLOT 1)**
       
       
      About the Atheros card:
      You can install ATH9KFixup (you will also need additional patches on 10.14+ to restore Atheros support) to enable this card, however,
      it will break sleep on MacOS 10.14+, it can freeze your OS at any time and it can freeze your network settings.
      Because of its instability it is highly recommended to buy a USB wireless adapter.
       
      You can find a list of working adapters, and the drivers, here.
       
       
      Additional things you will need:
      Latest Clover config (AcerAspireV5-571pg - CCE Bank) from here CloverEFI (download) or OpenCore (download - Untested) WhateverGreen (download) VoodooPS2 (download) VirtualSMC + SMCBatteryManager (download) AppleALC (download) Lilu (download) Mieze Realtek RTL8111 (download)  
      CloverEFI drivers you will need:
      ApfsDriverLoader EmuVariableUefi FSInject DataHubDxe VBoxHfs (if you have hfs partitions)  
      Remember to install BIOS drivers if you enable Legaby Boot.
       
       
       
      Feel free to ask for help.
      Please send me a PM if you have fixes or improvements, thanks.
    • By zkingtut
      Hello Everyone ,,
       
      I'd  like to share with you my experience with Lenovo ThinkPad P50 ( EFI , and Installation Process with some tips ) Hopefully to be useful for anyone who own Lenovo ThinkPad P50 
       
      Before start I want to show you my device specs , and I'm  sure 99% this will work too with any P50 have different spec. specially Intel i7 CPUs:
       
      - Intel Xeon E-3 1535 v5 ( P530 Intel HD Graphics )
      - 32 GB RAM
      - 256 GB SK Hynix Nvme SSD pc401 hfs256gd9tng-62a0a - for Mac OS  ( be careful not all nvme ssd are compatible)
      - 256 GB Samsung Evo 850 SSD - for Windows 
      - 4K Screen 
      - Nvidia Quadro M2000M 4 GB ( Useless - Disabled )
      - Intel WiFi Card ( Should be change to a compatible Broadcom one )
       
      BIOS SETUP :
       
      I highly recommend this steps before going to BIOS SETUP according to my experience with this Laptop :
       
            *( Update your BIOS Firmware to the latest one using windows )
       
            *( Remove Battery , Open the back cover and unplug the small CMOS BATTERY for about  4~5 minutes and put everything back again )
       
             * ( Remove any SSD HDD Nvme disks , USB , DisplayPort , Dock .. etc during installation, keep only the target Disk )
       
      -------------------------------------------
      Now Power your PC and Press F1 to enter the BIOS SETUP
       
         - Reset BIOS to its defaults
         - Adjust Date and Time 
         - Config ----> Network ---> Wake Up on Lan ( AC Only )
                                                         Network Stack ( Disabled )
       
        - USB ----> USB UEFI support  ( Enabled)
       
        - Display ------> Total Graphic Memory (256 MB)
                                     Graphic Device ( Hybrid)
       
        - RAID -----> Disabled
       
        - Security -----> Security Chip Selection ( Discrete TPM )
                                     Secure BOOT ( Disabled )
                                     Intel SGX Control ( Software Control )
       
        - Start Up ------>BOOT Priority order ( USB HDD - Mac OS Disk - Windows - and so on ....... with this order )
                                     UEFI/Legacy ( UEFI Only )
                                     CSM Support  ( NO )
      ----------------------------------------------------------------------------------------------------------------------------------
       
      **   F1 to Enter Bios - F12 for Boot Menu
      ***   Delete the EFI Folder in your Installation USB and replace it with the Attached one 
      ****   Generate new serial for SMBIOS MacBook Pro 13.1
      *****    If your CPU is XEON then go to Config.plist CPU Section and Add 0x05A5 under Type ( Fix for Unknown CPU )
      ****** You can delete boot-args "brcmfx=1 & brcmfx-driver=#a" if you want , I used it in my case with 1820A card to fix wifi issue
      ******    After you successfully installed OS , now Copy the same EFI Folder to your main EFI Boot Disk Partition 
      *******    Now install all the attached KEXTS to "Library / Extensions"  using Hackintool.app or by any method and rebuild cache and repair permissions
      ********    Check and compare the KEXTS in Library/ Extensions and Delete the repeated ones from Clover / Kexts / Others ( Important don't duplicate the same kexts here and there )
       
      FYI : LiluFriend.kext include ( Lilu , WhatEverGreen, AppleALC , AirportBrcmFixup ) All In One 
       
       
       
      You are Done 
      ---------------------------------------------------------------------------------------------------------------------------------
       
      What is working :
       
      - 4K Intel HD P530 2048 MB 
      - AUDIO
      - CAMERA 
      - ALL USB 3 PORTS , NO THUNDERBOLTS 
      - Keyboard and TouchPad 
      - Battery indicator 
      - Display Brightness 
      - Sleep 
      - DSDT has been patched , USB Ports modified only to MacBookPro 13.1
       
                   See the Screen Shot 
       
      Important Notice For Future OS Updates Installations : 
       
      To avoid Kernel Panic during install any future updates process please remove ( FakeSMC.kext and LiluFriend.kext ) from Library/Extensions directory to Clover / Kexts / Others .
      After update process finish put them back to Library/Extensions and delete them from clover . I hope this is clear enough
      ---------------------------------------------------------------------------------------------------------------------------------
       
      Happy Hackintosh , Let me know if you have any issue or difficulties during installation or later , I will try to help you
       
       
      EDITED :
       
      Catalina 10.15.1 Update :
                     ( download the attached files for Catalina 10.15.1 if you like to update Mojave or to do a clean fresh update  )
       
       
      EFI.zip
      kexts.zip

×