Jump to content
glasgood

[SUCCESS][GUIDE] Glasgood's High Sierra CoffeeLake: ASUS STRIX Z370-G - i7-8700 - GTX1080ti - UHD

317 posts in this topic

Recommended Posts

Thanks for the guide! I've followed it and it's got me up and running using the same part specs. Using this PCIe and adaptor.

Research says Broadcom chip (4331) is supported.

WiFi is not working. 

 

- used your EFI-NVIDEA & removed the on board wifi chip.

- see info in the USB and PCI of System Report. But nothing in Network->WiFi. I cannot add a wifi interface in System Prefs->Network.

 

Would post screenshots, but right now I'm wiping and reinstalling because of a new panic around the the AppleACPICPU...

I've had lots of panics at the "IO80211controller" in the past when booting.

 

In addition: 

- added RehabMan's FakePCIID + FakePCIID_Broadcom_WiFi kexts. (both with kext wizard and in the EFI/Clover )

- modified the config.plist following the guide-airport-pcie-half-mini-v2, with "the-darkvoid KextsToPatch"

Any ideas?
 

Share this post


Link to post
Share on other sites
Advertisement

Hi Selie,

 

What motherboard are you using, is it the Asus ROG Z370-G Strix ? if so try:

 

1. Check BIOS settings

2. Update BIOS to version 0430 ( confirmed working with DSDT)

3. Reseat WIFI card / test if is seen in Windows Device manager or Linux Live Distro

 

If not using Asus ROG Z370-G Strix motherboard and using POST-INSTALL-EFI folder and you haven't already then..

 

1. Remove DSDT from EFI/CLOVER/ACPI/PATCHED

2. Remove SSDT-UIAC.aml  from EFI/CLOVER/ACPI/PATCHED

 

Do you really need to wipe and reinstall High Sierra because of a kernel panic ?  Why not just use your bootable USB installer to boot into OSX and remove offending kext etc..

I had no need to use FakePCIID etc for my build. Your card should work out of the box.

 

:)

Share this post


Link to post
Share on other sites

oh snap. cant boot at all now. get prohibited symbol. verbose seems to show 'still waiting for boot device'

I cant even boot from the USB. it throws the same error (although after different things)

 

is it worth changing the EFI folder on the stick to the pre install version ?

 

 

post-2351905-0-93926400-1515012248_thumb.jpg
post-2351905-0-78268600-1515012224_thumb.jpg

 

post-2351905-0-78268600-1515012224_thumb.jpg

post-2351905-0-93926400-1515012248_thumb.jpg

Share this post


Link to post
Share on other sites

oh snap. cant boot at all now. get prohibited symbol. verbose seems to show 'still waiting for boot device'

I cant even boot from the USB. it throws the same error (although after different things)

 

is it worth changing the EFI folder on the stick to the pre install version ?

 

 

 

I had same problem, boot back into High Sierra using USB installer. Then download the latest POST-INSTALL EFI folder that I have uploaded two hours ago, It has latest Clover boot-loader. 

Share this post


Link to post
Share on other sites

so pre-install EFI folder?

 

No, boot with USB installer, when you log into High Sierra then replace EFI folder on system EFI/ESP partiton with >>POST-INSTALL-EFI

Out of curiosity, try booting as normal.. but when you reach the Clover boot screen wait for a minute before clicking on High Sierra icon at Clover Boot Screen.

so pre-install EFI folder?

 

Just found out about the major flaw>> in Intel Chips

So far, everything seems ok with Clover v r4359 no intermittent prohibited symbol. 

Share this post


Link to post
Share on other sites

that seems to be me trouble, I cant boot from the USB - in fact Im not sure its actually trying to boot from the USB, its to the same point in verbose mode which is PTIDSensors: started.

stays there for a minute then symbol - do disk activity light either


i saw the thing about Intel too. also that 10.13.2 already mitigates the issue and that 10.13.3 will do more 

http://appleinsider.com/articles/18/01/03/apple-has-already-partially-implemented-fix-in-macos-for-kpti-intel-cpu-security-flaw

Share this post


Link to post
Share on other sites

that seems to be me trouble, I cant boot from the USB - in fact Im not sure its actually trying to boot from the USB, its to the same point in verbose mode which is PTIDSensors: started.

stays there for a minute then symbol - do disk activity light either

i saw the thing about Intel too. also that 10.13.2 already mitigates the issue and that 10.13.3 will do more 

http://appleinsider.com/articles/18/01/03/apple-has-already-partially-implemented-fix-in-macos-for-kpti-intel-cpu-security-flaw

 

Did you try booting to Clover boot screen, then wait for about 1 minute then click on the High Sierra icon ? I also again just got the prohibited symbol using updated Clover version, but was able to restart and boot back into High Sierra. I think that if you try and boot to quickly into High Sierra from Clover screen is why the prohibited sign appears, could be that some other process has not had enough time to load. Try waiting for about 1 minute at Clover screen then see if you can enter High Sierra.

Share this post


Link to post
Share on other sites

yep tried that, the main problem is that it just won't boot from USB, throws the same error at the same point. I've got no way of checking its actually booting from the device - is there anyway of stepping through the boot, i can see ACPI errors shooting past.

Share this post


Link to post
Share on other sites

yep tried that, the main problem is that it just won't boot from USB, throws the same error at the same point. I've got no way of checking its actually booting from the device - is there anyway of stepping through the boot, i can see ACPI errors shooting past.

You could try entering the bios, change usb setting from auto to enabled. Then try and boot, if you can’t boot go back to BIOS and reset usb back to auto then try and boot. I’m thinking a change in BIOS might reset ACPI / DSDT or the order it loads.

Share this post


Link to post
Share on other sites

Hi Selie,

 

What motherboard are you using, is it the Asus ROG Z370-G Strix ? if so try:

 

1. Check BIOS settings

2. Update BIOS to version 0430 ( confirmed working with DSDT)

3. Reseat WIFI card / test if is seen in Windows Device manager or Linux Live Dist

Same mobo as you. I've updated to 0430 as directed and checked the settings.

I'm at the same spot as @bifterx.

he Post-EFI has been copied over to the SSD.

I also got the prohibited screen during boot in verbose mode even after waiting. I'll wait longer and see.

 

Screenshot right before the prohibited boot fail. 

 

I saw you screenshot of the wifi card. I only have 2 cables where you have 3. Is this normal?

 

Share this post


Link to post
Share on other sites

Same mobo as you. I've updated to 0430 as directed and checked the settings.

I'm at the same spot as @bifterx.

he Post-EFI has been copied over to the SSD.

I also got the prohibited screen during boot in verbose mode even after waiting. I'll wait longer and see.Screenshot right before the prohibited boot fail. 

I saw you screenshot of the wifi card. I only have 2 cables where you have 3. Is this normal?

 

The cable that connects from card to the motherboard usb connector is for Bluetooth, do you have Bluetooth and is your WiFi card working ? I will have to do some testing to find out cause of intermittent acpi errors.

Share this post


Link to post
Share on other sites

The cable that connects from card to the motherboard usb connector is for Bluetooth, do you have Bluetooth and is your WiFi card working ? I will have to do some testing to find out cause of intermittent acpi errors.

Thanks for looking into the ACPI errors. I also will experiment with removing my 1070 ti, and booting with -nv_disable=1. 

 

As for the wifi card, it's possible it's a faulty one unless you know anything about this. Booting stops here if the wifi card is fixed to mobo.

So when you go to system prefs > network > + , you can see wifi? I cannot.

Share this post


Link to post
Share on other sites

phew, that was a bit of a butt clencher for a while! I had to change the CSM settings in the the bios from Legacy Only to UEFI and Legacy - dont know how/why it was set to legacy only, that allowed the boot from USB. Up to Desktop - swapped in new EFI folder etc. Success! Thanks for the help Glasgood - Im conscious that this isn't meant to be a support line so many thanks.

 

Just as an aside, whilst watching in verbose mode, the boot sequence takes a long time as it goes through this check multiple times (each time takes a while)

apfs_vfsop_sync:2928: failed to finish all  transactions in sync()! (err 16)

this appears to be related to TRIM being enabled by default on an SSD - whether it supports it or not. (the EVO 960 does support it) but that seems to be the big holdup during boot.

 

Anyway Thanks again.

Cheers

Rob

Share this post


Link to post
Share on other sites

 

I saw you screenshot of the wifi card. I only have 2 cables where you have 3. Is this normal?

 

 

If you have Bluetooth enabled then the cable with two wires is working, I'm not an electronics expert or amature, but if you have two cable's and I have three then I possibly may have an earth cable. Test WiFi card with Linux or Windows to confirm fault.  :)

Share this post


Link to post
Share on other sites

nuts. came back this morn and the machine had restarted back to clover boot. won't boot again. prohibit symbol. stops at PTID sensors: started. won't boot boot from USB.

The only thing I changed from the new EFI and boot loader was added Rehabmans  HW monitor kexts.

Share this post


Link to post
Share on other sites

nuts. came back this morn and the machine had restarted back to clover boot. won't boot again. prohibit symbol. stops at PTID sensors: started. won't boot boot from USB.

The only thing I changed from the new EFI and boot loader was added Rehabmans  HW monitor kexts.

 

Can you update BIOS to this >> latest version then boot with USB installer and replace system EFI  folder with >> this one  . I have removed HW monitor kexts .

Share this post


Link to post
Share on other sites

Thanks for the awesome guide, glasgood. I've been following along with the updates and it's a great journey.

 

Some improvements I made to my own EFI that could work for everyone:

- Replaced apfs.efi with the latest version in 10.13.2, this removes the apfs related error messages when booting into Clover. apfs.efi.zip

- Added kexts to enable hardware video encoding/decoding using the Intel iGPU with Nvidia. Need to add shikigva=12 in boot args videodecodekexts.zip

- Added CodecCommander to fix audio issues after sleep. CodecCommander.kext.zip

 

Hope this helps!

Share this post


Link to post
Share on other sites

bios ver 0605 or 0606 (on asus site)?

 

On the Asus UK site it only has Version 0605 listed, thats the one I'm using.

Share this post


Link to post
Share on other sites

I'll go lockstep with your setup.

ASUS Uk now showing 0606 updated today

 

https://www.asus.com/uk/Motherboards/ROG-STRIX-Z370-G-GAMING-WI-FI-AC/HelpDesk_BIOS/

 

I tried to update to  v0606 via BIOS internet update, but got Asus message saying that v0605 was the most unto date BIOS. So far using latest EFI folder that I have uploaded, I have shutdown and restarted my machine numerous times and no ACPI related errors have been able to sucessfully boot into High Sierra. No prohibited signs, fingers crossed. Looks like old BIOS update and combined possibly with DSDT may be causing the ACPI errors. I think the HWsensors may have caused a separate system halt.

Thanks for the awesome guide, glasgood. I've been following along with the updates and it's a great journey.

 

Some improvements I made to my own EFI that could work for everyone:

- Replaced apfs.efi with the latest version in 10.13.2, this removes the apfs related error messages when booting into Clover. attachicon.gifapfs.efi.zip

- Added kexts to enable hardware video encoding/decoding using the Intel iGPU with Nvidia. Need to add shikigva=12 in boot args attachicon.gifvideodecodekexts.zip

- Added CodecCommander to fix audio issues after sleep. attachicon.gifCodecCommander.kext.zip

 

Hope this helps!

 

 

Hi ryokun6,

 

Thanks for sharing this, will try out the updated apfs.efi. I did have CodecCommander.kext installed, but removed it whilst troubleshooting the prohibited boot sign.

I have got hardware encoding working, I tried shake.kext and different flags to try and get iTunes streams working but had no success. As it stands I have Hardware Encoding enabled

using MacX Video Convertor Pro.  Will add CodecCommander soon  :)

Thanks for the awesome guide, glasgood. I've been following along with the updates and it's a great journey.

 

Some improvements I made to my own EFI that could work for everyone:

- Replaced apfs.efi with the latest version in 10.13.2, this removes the apfs related error messages when booting into Clover. attachicon.gifapfs.efi.zip

- Added kexts to enable hardware video encoding/decoding using the Intel iGPU with Nvidia. Need to add shikigva=12 in boot args attachicon.gifvideodecodekexts.zip

- Added CodecCommander to fix audio issues after sleep. attachicon.gifCodecCommander.kext.zip

 

Hope this helps!

 

The new apfs.efi is good, the verbose text just before Clover boot screen is gone. Boot seem slightly faster. Again, thanks for sharing this.  :thumbsup_anim:  :thumbsup_anim:  :thumbsup_anim:

Share this post


Link to post
Share on other sites

Why is Atheros E2200 Ethernet in the zipfile? 

Why is the older (1.2.0, not 1.2.1) of Apple ALC in there? 

Realtek 8111 driver - why? 

 

 Questions  :) I've just recreated the USB installer will update it, been busy this morning . Use --> Post Install Folder at top of listing. 

Share this post


Link to post
Share on other sites

I tried your updated EFI earlier this morning and I didn't get the prohibited sign once.

 

Everything went so well until just a moment ago I restarted and couldn't load the Nvidia Web Driver. I removed the DSDT and it worked, now the computer can't recover from sleep.

 

Haha. Gotta keep trying.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By glasgood
      GLASGOOD'S
       
      MOJAVE HACKINTOSH GUIDE 
       

       
       
       
      **FOR**  GIGABYTE Z390 AORUS PRO
       
       
       
       
      CREDITS & THANKS
       
      @MaLd0n
      His help with EFI configuration and DSDT
       
      CLOVER  TEAM
      Slice, Kabyl, usr-sse2, jadran, Blackosx, dmazar, STLVNUB, pcj, apianti, JrCs, pene, FrodoKenny, skoczy, ycr.ru, Oscar09, xsmile, SoThOr, rehabman, Download-Fritz, Zenit432, cecekpawon Et al
       
      APPLEALC
      Acidanthera, vit9696
       
      VOODOOHDA
      autumnrain, slice2009, zenith432
       
      ESP PRO MOUNTER
      @Micky1979 
       
      HACKINTOOL
      @headkaze
       
      CLOVER CONFIGURATOR
      Mackie100
       
      THEME ENGINE
      Alex Zielenski
       
      INSANELYMAC
      OLARILA
       
      Hackintool Tutorial
      daliansky
       
      Hackintosh Vanilla Desktop Guide
      /r/Hackintosh - corpnewt
       
       
      MONITORCONTROL
      JoniVR & theOneyouseek
       
       
       
      ------------------------------------------------------------------------------------------------------------------------------------------------------------
       
      UPDATES
       
       
      ------------------------------------------------------------------------------------------------------------------------------------------------------------
       
       
      PART LIST
       
      • Intel I7 8700 
      • Gigabyte Z390 AORUS PRO
      • Gigabyte AORUS RADEON RX 580 8GB ( connected to monitor with DisplayPort )
       
      • Corsair Vengeance LPX 16GB ( 2 x 8GB ) 2666MHz – CMK16GX4M2A2666C16  In this build, both memory modules are installed in memory slots DDR4_A1  and DDR4_B1 
       
      • Corsair RM650x 80 Plus Gold Power Supply Unit
      • Corsair H100i V2 AIO Hydro/Water RGB LED CPU Cooler
      • Samsung EVO 500GB SSD (2.5) macOS Mojave
      • Samsung EVO 250 GB SSD (2.5) Windows 10 Pro
      • NZXT H500 Mid Tower ATX Case
       
      • RECOMMENDED WIFI CARD → ABWB 802.11AC WI-FI With Bluetooth 4.0 PCI-Express (PCI-E) BCM943602CS  
      OR
      • WIFI and Bluetooth with BCM94331CD with PCI-e adapter (but will require AirportBrcmFixup.kext for AirDrop.. )
       
      ** Avoid Samsung EVO 970 PLUS as Hackintosh has problem with that device **
       
       
      WORKING
       
      • Sound 
      • HDMI Port on AMD RX580 / 590 ( Ensure you disable BIOS CSM if using HDMI on RX580 / RX590 )
      • HDMI Port on Aorus Z390 Motherboard ( Ensure you have correct BIOS settings as per this guide for Intel only)
      • Ethernet Port
      • WiFi
      • SSD Trim
      • USB 3.0 & 2.0 
      • AirDrop
      • iCloud
      • Hardware Acceleration
      • iMessages
      • Facetime
      • Handoff
      • Continuity
       

       

       
       
       

       
       
       
       
       
      PREAMBLE - BEFORE YOU START 
       
      Here detailed, is all the  steps towards building a successful and stable Aorus Pro Z390 Hackintosh, if you are a first time Hackintosher, this guide will have you quickly up and running with the Aorus Pro Z390 Hackintosh. To rule out any problems from the go,
      only have the disc that you plan to install macOS Mojave connected to the Aorus Pro, disconnect any other Windows / Linux or data drives, external drives from your Aorus Pro. Windows / Linux and data drives can be connected after successful installation of macOS Mojave
      If you have more than 16 GB of memory, then install macOS Mojave with just 16GB, you can later add any additional memory. Install memory modules in slots DDR4_A1  and DDR4_B1. This build has the Wi-Fi combo PCI-e card installed in slot PCIEX1_3
      with its 9 pin USB cable attached to motherboard header F_USB2. 
       
      If using the Corsair H100i v2 AIO cooler with USB cable connected to motherboard header F_USB1, you will need to enable hot-patch ( explained in guide ) in config.plist for working sleep, wake from sleep will only work by pressing Power Button.
      However, If not using the Corsair H100i v2  USB cable, then you have wake from sleep using Keyboard / Mouse or Power Button.
      The Corsair USB cable is only required if using Corsair Link software in Windows for custom Fan or LED settings.
       
      Install macOS Mojave on its own physical drive, so do not try and install macOS Mojave onto a free partition on a disc that contains Windows.
      Remove any Thunderbolt cards, Thunderbolt card can be reinserted after installation.  Double check your BIOS settings are the same as this guide. 
       
      Following are unsupported / problematic
       
      • Intel Optane ( if you have this, remove it before installation of macOS Mojave )
       
      • Samsung EVO Plus drives ( firmware problem with macOS )
       
      • XFX Radeon RX 580
       
      • NVIDIA GTX / RTX not supported in macOS Mojave
       
      • Fenvi T919 Wireless Card, it seems Bluetooth is not working out of box for some users ( Maybe the USB port attached to Fenvi bluetooth is wrongly configured, or the SSDT-UIAC.aml port connector was not configured as Internal, or maybe some other reason )
         Save yourself a headache --->  RECOMMENDED WIFI CARD WORKING OUT OF BOX (OOB)  is ---> ABWB 802.11AC WI-FI With Bluetooth 4.0 PCI-Express (PCI-E) BCM943602CS 
       
       
       
      Q - WILL THIS GUIDE WORK WITH MY NON AORUS Z390 PRO MOTHERBOARD ?
      A - Possibly may work with other Z390 chipset motherboards. See very bottom of page for PRE & POST - INSTALL AORUS X 390 EFI's ( will require USB SSDT fix  )
       
      Q - I notice you have the Aorus Pro Z390 version, will this guide work with Aorus Pro Z390 WiFi version ?
      A - Yes, but onboard Intel / Intel CNVi WIFII /Bluetooth will not work with macOS and you will have to disable HS14 for Bluetooth to function properly on BCM943602CS or BCM94331CD WiFi/Bluetooth Combo cards ( more info at bottom of guide) .
       
       
       
       
       
       
      PART 1 - DOWNLOAD 
       
       
      Download the following:
       
      • CLOVER
       
      • PRE-INSTALL Aorus Pro Z390 EFI - RX580.zip
       
      •  POST-INSTALL Aorus Pro Z390 EFI - RX580.zip
       
       
      //OPENCORE EXPERIMENTAL EFI FOR RX580==> EFI.zip
       
       
       
       
       
       
      // INTEL UHD 630 EFI  Aorus Pro Z390 EFI's below. For those who do not have a Graphics Card Installed in PCIe Slot, requires Initial Display Output BIOS setting to be changed to IGFX  spoiler below!
       
      •  PRE-INSTALL Aorus Pro Z390 EFI - Intel UHD630.zip
       
      •  POST-INSTALL Aorus Pro Z390 EFI - Intel UHD630.zip
       
       
       
       
       
       
      • ESP MOUNTER PRO v1.9
       
      • macOS MOJAVE 
       
      • CLOVER CONFIGURATOR
       
      • EmuVariableUefi-64.efi  ( Used only to initialise iMessages. It then must be removed from Clover drivers64UEFI folder as will cause intermittent memory allocation errors on boot, explained in guide)
       
       
      OPTIONAL DOWNLOADS
       
      • Native Display Brightness with MonitorControl
       
      • VoodooHDA.kext.zip 

      • ThemeEngine 
       
      • Assets.car 
       
       
      // Not really needed but IF no sound on Wake from Sleep then use SSDT-ALC1220 and CodecCommander
      • SSDT-ALC1220.aml  ( Resolves Audio Sound on Wake, place in Clover / ACPI / Patched )
       
      • CodecCommander.kext.zip ( Resolves Audio Sound on Wake, place in Clover / Kexts / Other )
       
       
       
       
      PART 2 - BIOS SETTINGS (version F9 )
       
       
      Here is a list of the BIOS settings that I have used ( Screenshots in spoiler below )
       
      • Enter BIOS → Press F12 → Enter Setup
      • Save & Exit → Load Optimized Defaults
       
      • BIOS → Windows 8/10 Features → Other OS
      • BIOS → CSM Support → Enabled
       
      • Peripherals → Initial Display Output → PCIe 1 Slot
      • Peripherals → Trusted Computing → Security Device Support →  Disable
      • Peripherals → Intel(R)Bios Guard → Intel BIOS Guard Support →  Disable
      • Peripherals → USB Configuration → Legacy USB Support →  Enabled
      • Peripherals → USB Configuration → XHCI Hand-off →  Enabled
      • Peripherals → Network Stack Configuration → Network Stack →  Disabled
      • Peripherals → SATA And RST Configuration → SATA Mode Selection →  AHCI
       
      • Chipset → Vt-d → Enabled
      • Chipset → Internal Graphics → Enabled
      • Chipset → DVMT Pre-Allocated → 256M
      • Chipset → DVMT Total Gfx Mem → MAX 
      • Chipset → Audio Controller → Enabled
      • Chipset → Above 4G Decoding → Disabled 
       
      • Power → Platform Power Management → Disabled ( Change to enabled after macOS is installed )
      • Power → ErP → Disabled  ( Can be enabled if you have RGB lighting that you want to power off when shutting down Hackintosh. Thanks @AudioGod for flagging this up)
      • Power → RC6 (Render Standby) → Disabled
       
      // IF USING  CORSAIR H100i V2 AIO CPU WATER COOLER 
      • MIT → Smart Fan 5 Settings → CPU Fan Control mode → PWM 
       
      • Save & Exit → Save & Exit Setup
       
      SCREEN DUMP SPOILERS
       
       
       
       
       
      PART 3 – CREATE A MOJAVE USB FLASH INSTALLER
       
      Prepare USB Installer for Mojave ( Video below )
       
      • Insert USB drive
      • Launch /Applications/Utilities/Disk Utility
      • Disk Utility → View → Show All Devices
      • On Left-hand panel → External →(Identify your USB device in left hand panel)
      • Click and highlight your USB device in the left-hand panel.
      • Click erase button.
      • Name: USB
      • Format: Mac OS Extended (Journaled )
      • Scheme: GUID Partition Map
      • Click Erase button.
       
      • Place the downloaded MacOS Mojave app into Applications folder.
      • Open Terminal copy and paste:
       
      sudo /Applications/Install\ macOS\ Mojave.app/Contents/Resources/createinstallmedia --volume /Volumes/USB --nointeraction && say Mojave Drive Created  • Enter
       
       
       
       
       
       
       
       
       
       
       
      PART 4 – INSTALL CLOVER ON THE MOJAVE USB INSTALLER 
       
      Make Mojave USB flash drive installer bootable.( Video below )
       
      • Launch Clover application, double click.
      • Click Continue → Continue → Continue 
      • Click Change Install Location button.
      • Click Install macOSMojave USB installer → Continue
      • Click Customise button
      • Choose:
      Clover for UEFI booting only Install Clover in the ESP Themes UEFI Drivers • Click Install button
      • Installation Complete!
       
      Video:
       
       
       
       
       
       
      PART 5 – CUSTOMIZE MOJAVE USB INSTALLER FOR AORUS Z390 PRO
       
      Replace Clover EFI folder with PRE-INSTALL Aorus Pro Z390 EFI - RX580.zip  OR  if NO graphics card installed in PCIe slot, then use PRE-INSTALL Aorus Pro Z390 EFI - Intel UHD630.zip( Video below ) 
       
      • Install ESP Mounter Pro v1.9
      • Using ESP Mounter Pro, Mount ESP on disk2s1 ( Your disk name may be different )
       

       

       
       
       
      • Open mounted EFI partition found on desktop
      • Copy all the contents from Aorus 390 Pro EFI folder
      • Replace USB EFI folder with all the contents inside the Aorus 390 Pro EFI folder.
       
       

       
       
       
       
       
       
       
      PART 6 – INSTALL MAC OS MOJAVE ON INTERNAL DRIVE
       
      INSTALL NOTE
       
      ENSURE BIOS: Above 4G Decoding is set to Disabled 
      if Above 4G decoding is set to enabled then macOS Mojave install will freeze at 2 mins remaining and will not shut down properly!!!!
       
      Please be patient during install, so when install gets to 2 or 3 mins remaining then it may take extra time. Be ready to boot from UEFI USB installer by pressing F12 when install initiates restarts. 

      • INSERT USB INSTALLER INTO THE USB 2.0 PORT  
       
       
       Here is a walkthrough of the full process using the macOS Mojave USB Installer on the Aorus Z390 Pro. 
       
       
       
       
      • Power on PC and press F12• Choose bootable USB drive from boot menu.
       
       
       
      • Install macOS Mojave to internal solid state or hard drive.
       
       
       
      When system returns to the Clover boot menu choose:
       
      • Boot macOS Install from Macintosh
       
       
       
      At next restart, press F12 and boot from external UEFI USB device and choose:
       
      • Boot macOS Install from Macintosh
       
       
       
      Proceed with macOS Mojave install
       
       
      macOS Mojave is now installed, but it can only boot at this moment thanks to FakeSMC and Clover on the Mojave USB flash drive installer.
       

       
       
       
       
       
       
      PART 7 – MAKE AORUS Z390 PRO INTERNAL DRIVE BOOTABLE
       
      Make internal drive bootable ( Video below )
       
      So far, the Aorus Pro can only boot the internal system drive with the aid of the Mojave USB Installer.
      To boot from the internal system drive without the installer: 
       
      Download and install Clover with RC Scripts on target volume.  
      If your Aorus Pro Z390 has AMD RX 580 then copy the EFI folder from inside POST-INSTALL Aorus Pro Z390 EFI - RX580.zip  folder and paste it inside the the System Drive EFI partition.          OR
      If your Aorus Pro Z390 has no graphics card installed in PCIe slot, then copy the EFI folder from inside POST-INSTALL Aorus Pro Z390 EFI - Intel UHD630.zip  folder and paste it inside the the System Drive EFI partition.   
       

       
       
       
      • Remove USB Mojave installer and shut down and restart.
       
      Aorus Hackintosh should now be able to boot to macOS Mojave, Done, well almost ! 
       
       
       
       
       
      PART 8 – ENABLE IMESSAGES & FACETIME 
       
       
      // UPDATE 21st MAY 2019
       
      Possibly Clover Configurator now automatically populates correct values for working iMessages when you select an SMBIOS.  
       

       
      After selecting SMBIOS, example iMac19,1 for Aorus Pro with RX580 ( image above ) then go to Apple and ensure you have the "serial number is not valid " message. Done!
       
      If you still have problems connecting to iMessage, test and ensure that AirDrop is working, then follow instructions inside spoiler. 

       
       
      • Mount internal drive EFI/ESP partition
      • Go to folder CLOVER → drivers64UEFI 
      • Place both EMUVariableUefi-64.efi inside → drivers64UEFI
       
       
      Using Clover Configurator, add the following argument to config.plist using Clover Configurator.
       
      • Slide = 0
       

       
       
      Shutdown and then press power on button on PC.
       
      • You should now be able to Log into iCloud, iMessages and FaceTime
       
       
       
      • NOW delete EMUVariableUefi-64.efi from CLOVER → drivers64UEFI Folder 
      • Shutdown and restart Aorus Pro hackintosh. iMessages etc is now operational without EMUVariableUefi-64.efi ( EMUVariableUefi-64.efi only needed to initialise iMessages )
       
       
      // UPDATE 22nd May 2019 
       
      • It seems that there are no "Couldn't allocate runtime area"  errors when continuing to use EMUVariableUefi-64.efi since updating to macOS Mojave 10.14.5 and using Clover version r4920. 
      • It is important to delete EMUVariableUefi-64.efi, this will avoid very intermittent boot errors such as: “Couldn’t allocate runtime area”  post errors.
       
       
       
       
      PART 9 – ENABLE TRIM for Solid State Flash Drives
       
      Open Terminal and enter the following command:
      sudo trimforce enable  
       
       
       
       
      DEFAULT SSDT –  USB PORTS FIX CONFIGURATION WITH FRONT USB-C - SSDT USBPorts.kext ALREADY INSIDE AORUS Z390 EFI FOLDER  – Provided by @AudioGod  
       
       

       

       
      If you have USBC on Computer Chassis / Case, then SS01 and SS02 is mapped to that USB C port 
       

       
       
       
       
       
       
      ------------    GUIDE FINISHED YOU SHOULD NOW HAVE WORKING AORUS Z390 PRO HACKINTOSH  WITH SSDT USB FIX   ------------
       
       
       
      OPTIONAL: Set Wi-Fi Country Code
       
       
       
       
       
       
      OPTIONAL: System Information - PCI
       
       
       
       
       
       
       
      External USB Storage:  Fix "disk did not eject properly" message upon wake from sleep
       
       
       
       
       
       
       
      OPTIONAL:  Native Display Brightness - with MonitorControl

       
       
       
       
       
       
      OPTIONAL:  Dual Boot macOS Mojave & Windows 10 
       
       
       
       
       
       
       
       
      OPTIONAL:  Replace the default "About This Mac" Apple Logo with RED AORUS APPLE
       
       

       
       
       
       
      OPTIONAL - ALTERNATIVE SSDT 1 –  SSDT Ports configuration below - replace SSDT inside Clover /ACPI/PATCHED folder 
       
       
       
       
       

      OPTIONAL - ALTERNATIVE SSDT 2 -  SSDT Ports configuration below - replace SSDT inside Clover /ACPI/PATCHED folder 
       
       
       
       
       

      OPTIONAL - ALTERNATIVE SSDT 3 – Create your own SSDT
       
       
       
       
       
      FRAMEBUFFER PATCHING  – For working Intel UHD 630 Graphics, working HDMI Port, working HDMI Audio on Aorus Z390 Pro
       


       
       
       
       
       
       
      FINAL CUT PRO  – Configuration for AMD RX5xx 
       
       
       
       
      AORUS PRO Z390 WIFI version with Intel CNVi  – Disable Bluetooth on HS14
       
      Resolve bluetooth issue  reported by @eSaF 
       
       
       
       
       
       
      CLOVER  – Updating / Upgrade Clover boot loader 
       
       
       
       
       
       
      SLEEP  – Sleep and Automatic Sleep

       
       
       
       
       
       
       
       
      SLEEP  – Resolving Instant Wake ( Corsair H100i v2 AIO )
       
       
       
       
       
       
       
       
      WIFI  – Clover Hotpatch PXSX to ARPT
       
       
       
       
       
       
       
       
       
       
      RECOMMENDED READING  – Excellent Hackintosh Vanilla guide created by CorpNewt with in depth tutorial on Clover.  
       
      https://hackintosh.gitbook.io/-r-hackintosh-vanilla-desktop-guide/config.plist-per-hardware/coffee-lake
       
       
       
       
       
       
       
       
       
      AORUS Z390 MOTHERBOARD X  – EFI WITH NO USB SSDT, WITH PORTS LIMIT PATCH, WITH SSDT-GPRW SLEEP / WAKE FIX
       
      Q - I notice you have the Aorus Pro Z390 version, will this guide work with other Gigabyte Aorus Z390  motherboards ?
      A - Possibly, but it is not guaranteed that these EFI folders below may work. 
       
       
      PRE-INSTALL Aorus X Z390 EFI - RX580.zip
      POST-INSTALL Aorus X Z390 EFI - RX580.zip
       
      PRE-INSTALL Aorus X Z390 EFI - Intel UHD630.zip
      POST-INSTALL Aorus X Z390 EFI - Intel UHD630.zip
       
       
       
       
       
       
       
       
       
       
       
       

       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
      SSDT-UIAC.aml.zip
      SSDT-UIAC.dsl.zip
       
      CodecCommander.kext.zip
      SSDT-ALC1220.aml.zip
       
      POST-INSTALL Aorus Pro Z390 EFI - RX580 2.zip
    • By fusion71au
      Clover r4961 ISO compiled with GCC and minimal config.plist compatible for use in VMWare Workstation.
       
      Tested with unlocked Workstation 15 running OSX 10.9 -->10.14 guest in Windows X64 host.
       
      Installation
      1. Download and unzip "EFI_Clover_r4961 for VMware.zip". Mount Clover-v2.4k-4961-X64.iso by double clicking on it.
      2. Mount your VM's EFI System Partition eg in terminal
      sudo diskutil mount disk0s1   3. Copy EFI folder from step 1 into the EFI partition
      4. Shutdown the VM, add bios.bootDelay = "3000" to your VM's vmx file
      5. Reboot your VM, press <F2> to access the VMware Boot Manager and add CLOVERX64.efi to the boot menu.
       
      Substitute your own unique and valid MLB and ROM variables in the /EFI/CLOVER/config.plist (Rt Variables section) to activate iMessage/Facetime on your VM.
    • By gengik84
      Ciro82==>>Thanks
      Uno dei tre Requisiti:
      Hack funzionante Mac vero Macchina virtuale Impostazioni Bios per il boot:
      Cercate una voce  del tipo “Sata Mode”e settatela  in AHCI
      Secure Boot: disabilitare o altri sistemi operativi
      CSM: UEFI o LEGACY, oppure a secondo del tipo di installazione
      VT-x / VT-d disable
      *Nota: Secure boot e csm valido solo per bios UEFI
      Materiale Occorrente 
      "OS X (Versione App.Store)”
      USB 8GB  *nota: nel caso di usb superiori dovrà essere partizionata, in modo da avere una partizione su cui "lavoreremo,di questa dimensione
      ShowAllfiles 
      kext Wizard 
      Bootloader Clover_2.3k_r xxx:                   http: //sourceforge.n.../cloverefiboot/
      Clover Configurator:                                    http: //mackie100proj...a.org/download/
      FakeSmc.kext:                                            https://github.com/kozlek/HWSensors/releases
      In allegato,a fondo pagina troverete un "pacchetto" contenente : ShowAllfiles, Kext Wizard, FakeSmc.kext: 
      App alternative:
      ESP Mounter Pro: per montare la partizione EFI
      Vi illustrerò tre metodi per creare la usb, ma sono ben distinti… quindi usatene soltanto uno
      Metodo 1: “Install Mac_OS_X.command” Metodo 2: “Create Install Media di Apple” Metodo 3:  Metodo Manuale Alla fine delle preparazione dell’installer, tutti i metodi necessitano l’installazione del Bootloader Clover sulla a vostra USB.
      “CONDIZIONI OBBLIGATORIE”
      PUNTO 1: che la vostra usb sia stata preventivamente nominata USB (caratteri maiuscoli) Tabella di partizione GUID e la formattazione in  Mac esteso Journaled.
      PUNTO 2: che l’installer di OSX si trovi in Applicazioni
      Utility Disco 
      Selezionate la pendrive, andate su “partizione”, selezionate “1 partizione”, impostate Mac OS esteso journaled e date il nome USB, poi in basso cliccate su opzioni e scegliete Tabella partizione (GUID), poi “applica”.
      Immagine 
      Riporto nuovamente l’operazione sopra citata adoperando dal nuovo Utility Disco introdotto su El Capitan.
      Rimane ovviamente invariato nome della usb in ==>> USB (maiuscolo), la formattazione in Mac esteso Journaled e sia la mappa partizione in GUID
      Da utility disco selezionate la usb, cliccate su inizializza.
      dal menù a tendina scegliete la relative impostazioni
      Immagine  
      Procedura effettua da High Sierra è la stessa della precedente, l'unica attenzione e operazione da aggiungere in primis  è cliccare nel menù a tendina in alto sulla sinistra di utility disco e selezionare "mostra tutti i dispositivi"
      Immagine 
       
      =====================
        METODO 1: "Install_Mac_OS_X.Command" Lo script che trovate allegato in fondo alla guida permette la creazione dell’installer in maniera automatica
      Include la possibilità di scelta di tre versioni di osx
      Yosemite El Capitan Sierra Il risultato finale è come quello del metodo "manuale" descritto nella guida, per cui l'installazione avverrà in un solo passaggio, non in due come con il metodo createinstallmedia. 
      Offre inoltre la possibilità di inserire un kernel patchato, utile, per esempio, per chi usa AMD.
      Rimane invariato il nome dato alla usb in USB, mappa partizione e tipo di formattazione
      Se la vostra usb non sarà rinominata nel modo corretto, verrete avvisati dal terminale, quindi non dovrete far altro che apportare la relativa modifica e rilanciare nuovamente lo script
      Esempio
      ===========================
      Metodo 2 
      L'intento è quello di usare la procedura fornitaci direttamente da Apple, "createinstallmedia", introdotta  con Mavericks. 
      Tale metodo prevede l’uso del terminale che via via se ne sta perdendo il “valore e l’uso”
      Inizialmente per i neofiti potrà sembrare problematico ma alla fine non è così.
      Durante il post installazione alcune operazioni ne richiedono l’ uso.
      Perciò mi sono chiesto perchè, qualora uno volesse, non far conoscere da subito un po’ questo “strumento”???
      Per favorirvi vi ho allegato i comandi già  “pronti”, i quali li potrete copiare ed incollare sul terminale.
      A questo punto aprite il terminale, copiate ed incollate il comando sottostante e premete invio, digitate la vostra password e premete nuovamente invio.
      Comando per creare USB con Yosemite:
      sudo /Applications/Install\ OS\ X\ Yosemite.app/Contents/Resources/createinstallmedia --volume /Volumes/USB --applicationpath /Applications/Install\ OS\ X\ Yosemite.app --nointeraction  
      Comando per creare USB con El Capitan
      sudo /Applications/Install\ OS\ X\ El\ Capitan.app/Contents/Resources/createinstallmedia --volume /Volumes/USB --applicationpath /Applications/Install\ OS\ X\ El\ Capitan.app --nointeraction Comando per creare USB con Sierra 
      sudo /Applications/Install\ macOS\ Sierra.app/Contents/Resources/createinstallmedia --volume /Volumes/USB --applicationpath /Applications/Install\ macOS\ Sierra.app/ --nointeraction Per creare USB con Hight Sierra o Mojave usate --> C_I_M (aggiornato per 10.14)
       
      Funziona con il drag & drop sul terminale, in questo caso non vi è necessità che la usb sia nominata in un determinato modo ed essendo basato su create install media ovviamente funziona da 10.9 a 10.14.... 
      BENE…IL PROCESSO DI CREAZIONE E’ INIZIATO…
      AVREMO CIRCA 20/30 MINUTI DI TEMPO LIBERO A CUI DEDICARSI A CIO’ CHE VOGLIAMO………………………………………..  
      COLGO L’OCCASIONE PER FARVI NOTARE LA VELOCITA’ E LA SICUREZZA DI QUESTO METODO
      CONFRONTATE QUESTO CON IL TERZO METODO E NOTERETE CHE CON UN SOLO PASSAGGIO, OSSIA IL COMANDO DATO AL TERMINALE, FACCIAMO IN UNA SINGOLA OPERAZIONE TUTTI I VARI STEP DESCRITTI SULL’ ALTRO METODO.
      DETTO QUESTO, MOLTO IMPORTANTE E’ SOTTOLINEARE CHE COSI’ FACENDO EVITEREMO ERRORI  DI DISTRAZIONE RIGUARDO AI PASSAGGI O FRAINTENDIMENTI.
      Immagine 
      Potete adesso passare ad installare il bootloader Clover sulla vostra usb.
      *NOTA*:
      Avendo usato questo metodo l'installazione si dividerà in due fasi, perciò dopo il primo riavvio e necessario far partire nuovamente l'installer, selezionare lo stesso disco senza formattarlo.
      Finita questa ulteriore fase , l'installazione sarà terminata
      =========================
      METODO "MANUALE"....  (lascio per futura memoria-Compatibile fino a 10.12)
      ==========================
      Bootloader
      **Nota:** Installazione in UEFI  dipenderà dalla scheda madre in vostro possesso, quindi se non supporta tale opzione , il bootloader dovrà essere installato in  modalità Legacy.
       Vi invito, qualora non sapeste questa informazione, a recarvi nel sito ufficiale del produttore e controllare le informazioni a riguardo
      Fatto questo dobbiamo installare  Clover sulla usb.
      A seconda del tipo di Bios o al tipo di installazione che vogliamo fare UEFI o Legacy avremo ovviamente configurazioni diverse in questa fase.
      Lanciate il pkg.
      Immagine 

       
      Cambiate la destinazione di installazione ad USB oppure Install Mac_OS_X (a secondo del tipo di creazione eseguita)
      Successivamente clicchiamo su "Ad Hoc"
      Per Installazione UEFI
      Mettete i flag   : Installazione solo per avvio UEFI
                               : installare Clover nella ESP
                               : Driver64UEFI  AptioMemory --> (consigliato) 
                               : Driver64UEFI  ApfsDriverLoader --> (consigliato) --> sostituisce l'uso del driver apfs.efi
                               : Selezionate l'altri driver come da successiva immagine,
       
      *Nota: Altri driver che si possono usare  al suo posto  sono:
       informazioni 
       
      Proseguite con l’installazione.
      Immagine 
      ** Ricordate che avrete accesso a questa cartella dopo aver montato la partizione EFI**
      ===========================
      Per installazione Legacy
      Immagine 
      ===========================
      Impostazione per config.plist:
      Con clover configurator “montate” la partizione EFI della usb.
      1) Per fare questo nel menù di sinistra, cliccate su “Mount EFI”
      2) individuate la partizione relativa alla vostra usb, a questo punto montiamo la relativa partizione EFI  selezionando l’apposito pulsante “Mount Partition”
      Immagine 
      3) Successivamente cliccate su “Open Partition”.. recatevi in EFI/Clover ed aprite il config.plist
      4) Sezione ACPI: Disabilitate tutti i fix sia del menù 1 che del menù 2
      Immagine 
      5) Sezione BOOT: Sole se si sta installando Yosemite mettete il flag su kext-dev-mode=1
      Immagine 
      6) Sezione RT Variables: Se si sta installando El Capitan oppure Sierra, aggiungere i valori: BooterConfig= 0x28, CsrActiveConfig= 0x67
      Immagine 
      7) Sezione System Parameters: Su inject kext mettete YES
      Immagine 
      ===========================
      Nota: Su El Capitan, è stato introdotto SIP (System Integrity Protection)
      Info:
      ===========================
      Recatevi in EFI/Clover/kext/10.x 
      X= alla versione di osx che state installando. Per esempio se installerete Yosemite dovrete recarvi nella cartella 10.10, con El Capitan in 10.11….ecc
      Se non ci fosse tale cartella, createla e nominatela voi a “modo”.
      Copiatevi all’interno FakeSmc.kext
      *Nota se venite già da altre vostre configurazioni, oltre kext sopra citato ,potete mettere gli altri necessari per il vostro hardware
      Stessa cosa se avete DSDT e/o SSDT potete copiarli in EFI/Clover/Acpi/Patched
      Immagine 
      
      Per High Sierra:
      Scaricare il driver apfs.efi a fine guida, collocarlo:
          --> EFI/clover/Driver64UEFI se stiamo usando UEFI
      --> EFI/Clover/Driver64 se stiamo usando Legacy
       
      Per chi volesse continuare ad usare HFS vi rimando a questo post:
        Come installare High Sierra in HFS direttamente dalla usb  
      Utenti Laptop:  Nel 99% è obbligatorio disattivare la grafica discreta Nvidia/Amd per installare questo nuovo osx
                                     Quindi aggiungete --> SSDT-Disable_DGPU.aml.zip
                                     in EFI/Clover/acpi/Patched della usb
      --------------------------------------------------------------------
      Per Mojave:
      Scaricare il driver apfs.efi per 10.14 a fine guida, collocarlo:
          --> EFI/clover/Driver64UEFI se stiamo usando UEFI
      --> EFI/Clover/Driver64 se stiamo usando Legacy
      Versione di clover non antecedente a V_4015
      Volete usare HFS?
      E' possibile fare un installazione diretta su altro disco o partizione, nel caso può essere usato anche per effettuare aggiornamenti...
      nel caso guardate...
       Mojave in HFS 
       Oppure direttamente da usb  
       
      Fatto questo avrete la vostra USB bootable per installare OSX.
      ………Non scordatevi Fakesmc.kext da mettere nella relativa cartella…. senza il quale non farete mai il Boot......
      *NOTA: se usato il terminale per la creazione della usb, l'installazione si dividerà in due fasi, perciò dopo il primo riavvio e necessario far partire nuovamente l'installer, selezionare lo stesso disco senza formattarlo.
      Finita questa ulteriore fase , l'installazione sarà terminata
      **NOTA** Se avete processori Broadwell,Skylake o Kabylake...usate FakeSmc.kext e relativi sensors che trovate all'interno del secondo pacchetto.. (potete usarlo anche sui precedenti senza problemi, essendo una versione più aggiornata ha ulteriore supporto per le cpu più recenti)
      Update: Fakesmc e sensors versione 6.26
      Post installazione... post #2           
       Buon Hack….. 
      Aggiornamento:Install_Mac_OS_X.command.zip (compatibile da 10.10 a 10.12)
      le info le trovate a questo post
      Ringrazio @Ciro82 che mi ha aiutato nel preparare questa guida.
      Pacchetto.zip
      Pacchetto-2.zip
      Pacchetto-Fake+Sensors 6.26.1440.zip
      C_I_M.zip
       
      apfs.efi-10.14-beta1_No_Log.zip





       

    • By kushwavez
      Acer Aspire V15 V5-591G - Mojave 10.14.5
       
      (Note: mine is 55TU version, but the bootpack will work fine with another versions of 591G, for example: V5-591G-71K2, -764Z, -59PU, etc.)
      Specifications:
      - Motherboard: USOPP_SLS (Skylake-H PCH)
      - BIOS:Insyde Corp. v 1.15
      - CPU:Intel Core i5-6300HQ 2.3 GHz (Skylake)
      - GPU: NVIDIA GeForce GTX 950M 2 GB (Optimus) & Intel HD Graphics 530
      - RAM:SK hynix 4 GB DDR4 (Later I bought + KINGSTON 4 GB) 2133 MHz
      - WiFi + Bluetooth:Qualcomm Atheros QCNFA344A 5 GHz (Later -> Broadcom BRCM94352Z M.2 5 GHz WiFi + 4.0 Bluetooth)
      - Audio:Realtek HD Audio: ALC 255 
      - Ethernet: Realtek RTL8168/8111
      - Card Reader:Realtek USB 2.0 Card Reader (USB2.0-CRW)
      - Webcam:HD Webcam
      - HDD:TOSHIBA MQ01ACF032 320 GB HDD
      - SSD:SPCC M.2 230 GB SSD
      - Display:1366x768 (15.6", Matte)
      - Battery: 6 cell 56Wh / 5040mAh
      - Connectors: 
      1x SD Card Reader 2x USB 3.0 (1x USB Charging), 1x USB 2.0 1x VGA 1x HDMI 1x 3.5mm microphone/audio combined jack connector 1x Ethernet (Rj-45) - Keyboard & Touchpad:Multi-Touch & Multi-gestures ELAN 501 Touchpad, Backlight Keyboard.
      Working:  
      - Wi-Fi (with BCM94352Z)
      - Bluetooth hand-off (With BCM94352Z)
      -Full Graphics enabled on HD 530: ig-platform-id: 0x191b0000 (HD 530 Mobile)
      - Display: if default colour profile is corrupted (blue is not actual blue but purplish) Use "Rec. ITU-R BT. 709-5" Color Profile (System Pref. -> Displays -> Color)
      -HDMI & VGA Outputs: AppleGraphicsDevicePolicy.kext Clover patch
      - Audio (ALC 255):(Internal Speakers, Internal Microphone, Headphone jack with AppleALC, ALCPlugFix -> layout-id=17)
      - Ethernet Realtek 8168/8111: RealtekRTL8111.kext
      - App Store, Messages, FaceTime, Siri, iCloud(native)
      - Integrated webcam(native)
      - 3.0 USB (native)
      - Touchpad and Keyboard(ELAN501): Fn keys are good, the weird thing is the Brightness key. On my keyboard it's Pause Break:Br-up, Fn+F12:Br-dwn-> To fix this try Karabiner (VoodoPS2Controller.kext), - for gestures try SmartTouchpad drivers
      - Battery info:Install ACPIBatteryManager.kext with Kext Utility or other installer.
      - Sleep Mode
      - SSD with TRIM enabled (to enable trim, open Terminal and write "sudo trimforce enable")
      Not working:
      - Original Wi-Fi (Qualcomm Atheros QCNFA344A):  unsupported, you need switch to BCM94352Z or just use a mini usb wifi dongle.
      - NVIDIA GeForce GTX 950M: Optimus not supported.
      - Card Reader: Unsupported -> Can't really fix because I don't have any SD Card at the moment, maybe can be fixed by adding Prod & Ven IDs to AppleStorageDevices.kext, I never used it anyway. name: "USB2.0-CRW" Prod ID: "0x0129" Ven ID: "0x0bda  (Realtek Semiconductor Corp.)"
      For Wi-Fi:
      - 1st method:You can choose an external USB wifi dongle (I used TP-Link Archer T1U (5GHz support), TP-Link has official macOS drivers, you just need to install it
      -2nd and I think the best method:Replace your M.2 Qualcomm Card with a compatible BCM94352Zcard (you will have hand-off Bluetooth too), just install the kexts (enabled with BrcmFirmwareData.kext, BrcmPatchRAM2.kext, FakePCIID.kext, FakePCIID_Broadcom_WiFi.kext, they're all in my attached zip). You could buy this card from ebay, aliexpress, or amazon
       
      Issues:
      - None
      BIOS Settings:
      - BIOS version 1.15 (irrelevant)
      - Secure Boot: Disabled
      - Touchpad: Advanced
      - Boot mode:UEFI
      Getting ready for Installation:
      - Download the install zip (bootpack & postinstall): Click here -> acer_aspire_v591g_installfiles.zip
      Installation:
      - Create an installer with any method you know (- Mac: createinstallmedia - Windows: Transmac, Vmware, Win32diskimager)
      - Copy my Clover folder to the USB's EFI folder
      - Boot with the Installer USB
      - If you stuck in boot, reboot and in the Clover bootloader select "config_debug.cfg" -> you'll have more informations about the freeze
       
      Please open the README.rtf in my install zip for more informations about the USB Installer & Post installation!
      If you have a single RAM and getting panic at boot, then you need to edit the "config.plist" with these (SMBIOS->after "Version 1.0"):
      ->Edit "Frequency" and "Size" to match your RAM values
      <key>Version</key> <string>1.0</string> <key>Memory</key> <dict> <key>Channels</key> <integer>1</integer> <key>SlotCount</key> <integer>1</integer> <key>Modules</key> <array> <dict> <key>Slot</key> <integer>0</integer> <key>Size</key> <integer>8192</integer> <key>Frequency</key> <integer>2133</integer> <key>Type</key> <string>DDR4</string> </dict> </array> </dict> </dict>  
      PowerManagement  fix:
      Set HWPEnable=YES in Clover (already set), CPUFloor to "700", Frequency to "2300" and "3200"(Normal and Turbo, if you have i7-6700HQ version then it should be "2600", "3500") and "FrequencyVectors" from "0x0d000000" to "0x07000000" in "S/L/E/IOPlatformPluginFamily.kext/Contents/PlugIns/X86PlatformPlugin.kext/Contents/Resources/Mac-A5C67F76ED83108C.plist", MSR _xcpm_idle Patch to KernelToPatch in Clover (If you have High Sierra, change "MatchOS" to 10.13):

      <key>KernelToPatch</key> <array> <dict> <key>Comment</key> <string>MSR 0xE2 _xcpm_idle instant reboot(c) Pike R. Alpha</string> <key>Disabled</key> <false/> <key>Find</key> <data> ILniAAAADzA= </data> <key>MatchOS</key> <string>10.14</string> <key>Replace</key> <data> ILniAAAAkJA= </data> </dict> </array> Reboot, and it's 800MHz in idle state, same on Windows.
       

       
      Elan SmartTouchpad
      I only use scrolling, one-, double- & tripletap
      If you want to try other gestures go to this link for more informations, options (v4.7 beta 5) ->  DETAILS ABOUT THE SMART TOUCHPAD DRIVER FEATURES
      Fn Brightness keys not working with this, tried several things without success. With VoodoPS2Controller it's working, but you'll have no gestures (neither scrolling).
       
       
      Before updating to a new version of Mojave please update kexts (and clover if necessary) to newer versions to avoid kernel panics.
      Generate a serial number with Clover Configurator.app (open up your config.plist with CC then -> SMBIOS -> Serial Number -> Generate New)
       
      Mojave & Windows 10 Dual-Boot:
      Dual-boot clean install (on one drive), UEFI Only:
       
       Boot into your Mac installer, Create 2 partitions in GUID table (1 for Win (I used FAT32 but I think it doesn't matter what you choose), 1 for Mac),   Install Mac, boot with your USB, mount your EFI partition (use terminal or an EFI mounter app), create an EFI folder (if there is no folder), copy the CLOVER folder I attached to the EFI folder, restart,  Boot into your Win installer, Format the partition you created for Win, install.   Now, it's automatically booting into Windows. To use Clover open cmd in administrator, type:  bcdedit /set {bootmgr} path \EFI\CLOVER\CLOVERX64.efi       5.  You're done! It will booting into Clover when you start the system, and you can select Win or Mac (or another OS if installed on a 3rd partition).
       
      Dual-boot with Windows installed first (on one drive), UEFI Only:
      If you already have Windows and you don't want to lose all your data there is a hope:
      I created a video from this restore method: [Hackintosh] Dual-Boot High Sierra & Windows - when Windows already installed - no data waste - UEFI
      You need bootable Mac Installer and a full system restore image (link is in my video's description).
      (You may see errors if your EFI partition is not 200 MB)
       Boot into your Windows, resize your partition or create one for Mac.  Boot into your Mac installer and in Disk Utility format the partition you created.  Restore from image: select your full system restore image.  When it's finished restoring you just need to restart, then boot to the system with your usb.  When you successfully booted to Mac desktop, mount your EFI partition (use terminal or an EFI mounter app), open EFI, you will see there is a Microsoft folder already (don't touch that!). Copy my CLOVER folder to the EFI folder then Restart.  Now, it's automatically booting into Windows. To use Clover open cmd in administrator, type:  bcdedit /set {bootmgr} path \EFI\CLOVER\CLOVERX64.efi       7.  You're done! You can select your old Windows and your new macOS!
      (Only tried with Windows 8/8.1/10. I don't know Windows 7,etc.)
       
      IF YOU GETTING ERRORS DURING MAC RESTORE:
      - Make sure you have partitions in GPT
      - Windows using 100 MB EFI and will annoy the Mac restore. Don't worry, just ignore the errors.
       
      IF YOU GETTING ERRORS DURING WINDOWS INSTALLATION (could not be formatted, etc):
      - Make sure you have GPT partitions, and GPT (UEFI) installer, also disconnect all external storage drives (except the installer USB)
       
      IF YOU USED RESTORE METHOD THEN CAN'T MOUNT YOUR EFI PARTITION (No EFI partition found):
      - It's because your EFI is not 200 MB or not an "Apple" original EFI,  but do not worry, try another EFI mounter, or mount from terminal (I used EFI mounter v3: Getting errors, but you can mount and use without problem)
      - You also could "mount" the EFI from Windows:
      1st method: open cmd in administrator mode and type:
      diskpart
      list vol (Now select the "System" volume,(FAT 32) For example I select 4)
      sel vol 4
      list part(Select System type partition, for example 2)
      sel part 2
      assign letter=b(This will "mount" your EFI partition)
      Open Explorer++ or TotalCommander in administrator mode to manage EFI
      remove letter=b (This will "unmount" your EFI)
      2nd method: open cmd in administrator mode and type:
      mountvol b: /s (This will mount your EFI)
      Open Explorer++ or TotalCommander in administrator mode to manage EFI
      mountvol b: /d (This will unmount your EFI)
      Thanks to all OSXLatitude members for helping me out! (Jake Lo, Hervé, Bronxteck, black.dragon74)!
      Notes:
      2019.06.05: Updated to 10.14.5 -> no problem when/after installing
      2019.04.25: Optimized touchpad scrolling -> updated install files
      2019.03.30: Fixed USB 3.0 ports, fixed Bluetooth crashes after sleep -> updated bootpack
      2019.03.28: Updated to 10.14.4. Unexpected crashes while updating to 10.14.4 -> fixed by updating Clover to the latest (v4910) version. Bluetooth crashes appeared -> fixed by downgraded Brcm*.kexts. Updated bootpack.
      2019.02.24: Bluetooth crashes after sleep -> fixed, updated bootpack. 
      2019.02.22: Updated to 10.14.3. Fixed HDMI Audio by installing "FakePCIID_Intel_HDMI_Audio.kext" -> fixed freezing during boot. Fixed brightness levels by installing "AppleBacklightFixup.kext". Also updated bootpack & postinstall zip down in attachments.
      2019.01.21: Removed FakeSMC.kext, SMCHelper-64.efi, replaced by VirtualSMC.kext, VirtualSMC.efi because I got random freezes when booting system (kextd stall[0], (120s): 'AppleACPICPU' -> CPU is at 100%, fans are spinning fast), also updated bootpack in the attachments "acer_aspire_v591g-55tu_clover.zip"-> Freeze continued, brought back FakeSMC, deleted VirtualSMC (caused BT crashes).
      2019.01.18: HDMI Audio is fixed, I didn't do anything HDMI Audio is not fixed, sometimes it worked but most likely not. (no idea why)
      2018.12.09: Updated to 10.14.2 -> did without any complication
      2018.11.28: Fixed combo-jack garbage sound output by installing ALCPlugFix and CodecCommander.kext
      2018.11.01: Updated to 10.14.1 -> HDMI & VGA ports are gone again. -> Fixed by "AppleIntelSKLGraphicsFramebuffer.kext" rollback from 10.14.
      2018.09.28: Updated to Mojave 10.14 -> Fixed HDMI & VGA Outputs by adding "AppleGraphicsDevicePolicy.kext" patches to config.plist, HDMI audio not working
×