Hi to all of you happy users of hackintosh community !
This is my first post here on InsanelyMac and it will be a bit longer because I have a problems that I couldn't solve without someones help who's a bit more experianced then me in tweaking and patching a hackintosh.
This laptop will be a present to someone and I have only one week from now to finish it up and then I have to send it abroad. Thanks in advance.
The configuration is dual boot with prior Widows 10 installed on Samsung EVO 850 - 250 GB partitioned like:
1st partion was 100 MB EFI and is now 550 MB after deleting second Windows MSR partition
2nd partiton is still 16 MB MSR Windows
3th partition is Windows 10 NTFS with 99 GB
4th partiton is Downloads NTFS with 70 GB
5th partition is OSX Extended journaled with 35 GB
6th partition is OSX Recovery Extended journaled with 620 MB
7th partition is Acronis FAT32 with 27GB
It's a Dell Inspiron 7537 Notebook:
Motherboard Product: 038M0M - Intel Lynx Point-LP, Intel Haswell
BUS ratio: min 8 max 20, 20, 28, 31 x 100 MHz
CPU and RAM: Mobile DualCore Intel Core i7-4510U CPU @ 2.00GHz - RAM: 16GB DDR3 - 1600MHz
Graphics: Intel HD Graphics 4400 and nVIDIA GeForce GT 750M 2GB
Monitor: LP156WF4 Dell 890N5 @ 1920 x 1080 - Touchscreen
BIOS: A14 - Audio: Realtek ALC283 - Intel 8 Series Chipset SATA AHCI
WiFi: Intel Wireless N7260/Bluetooth is changed for Broadcom BCM94352HM
CardReader RTL8411B - 4 Intel USB 3.0 ports
Webcam - DWGV8
SSD 850 EVO 250GB
I have found on the internet working installer image with Sierra 10.12.4 and I placed it on the USB with TransMac and I tried to install it, but it didn't work right from the box untill I didin't find a "good" .config file with good flags for this laptop and I replaced it in the Clover. It has Clover 4049 in the EFI partition on the USB installer.
That was my first problem to get Clover working on SSD but after some time I succeed to install the newest Clover 4128 on the SSD - EFI partition.
I have installed at least 10 times this Sierra image on this laptop before I came here to post all of this because apparently I make always same mistake and I can't go any further with it. I hope that I did not messed too much with all of this because there is still working Windows 10 with working 4128 Clover. The only problem is that in biginning after first few times unsuccessful install of OSX I had different behavior then now of OSX if I would like to start it from SSD.
In beginning, if I check flag -V and I try to start from SSD it will come to one point and it will hang enternally at that point and I must to restart notebook via the power button because it will never boot to OSX desktop without USB installer. I "played" apparently a bit too much and after changing and putting the same . config to EFI partition on Clover and sometimes even Clover will not show up untill I don't swich off the power on notebook.
I went further and I thought, O.K. I will continue with installing kexts to see what I can get working. It was also not so easy and acctually I still don't know exactly which kext I really need to install and what I should avoid to install assuming I didn't use any patched DSDT cause I never make it so far.
What I got it to work somehow till now with Pandora's Box (Before that I tried and other post install tools as Vietnam tool 1.9.6 with not so much succes, actually after using the Vietnam tool I got this kernel panic and immediate rebooting if I try to boot from SSD and it's never gone even after deleting the whole OSX partition and Pandora's box is noob's friendly tool) is:
Booting from USB installer, Sound, Ethernet, USB (but I don't know if it's full speed or not) Some hardware monitoring info, touch pad and keyboard, trimming.
I changed internal WiFi Intel N7260 card with bluetooth for the one Broadcom BCM94352HM WiFi+Bluetooth card which is here and overall advertised as working out the box with OSX but I didn't get it working untill now.
Dedicated Nvidia GT 750M video card is not working and also Intel HD 4400 looks a bit too slow by opening applicatons box in the OSX.
Webcam doesn't work, hibernate doesn't work, touchscreen doesn't work and booting from SSD doesn't work.
This time I have installed OSX again and I have pressed F4 to extract my original DSDT file from this notebook(I don't know if it does a metter that I pulled DSDT.aml file after install of OSX and not before installation, I mean after rebooting) but I didn't boot to finish installing until I don't get good information from someone who knows where I make mistake. I only tried to boot once from SSD to see if something is changed with immediate kernel panic, but there is still one there waiting to be removed.
- I have attached here Clover config file which is in the EFI partition on the USB and it's a same config file from EFI on the SSD.
- Also I have attached an already patched DSDT file for Dell Inspiron 7537 which I found here in Download section but it is patched for El Capitane and is not from this laptop so I don't know if it can help.
- I also added a full folder of Clover from the EFI partition on the SSD.
Who can help me to bring this installation to the end ?
I have not so much time to finish it so please don't hesitate to help me in it. Thanks !
Greetings from Holland !
Config file from EFI partition in Clover.7z
Patched DSDT from InsanelyMac for El Capitan.7z
Not patched DSDT from this Dell 7537.7z
CLOVER from EFI partition on the SSD .7z
The is the Post-Install topic following the Ryzen Clover Installation Guide for macOS Sierra.
If you have yet to install Sierra on your Ryzen machine, check out that thread for help installing.
Here we can discuss post install troubleshooting such as well known issues with NVIDIA Drivers, audio interfaces, etc.
Here is one workaround for audio that I am using - My audio was not working and I spent days trying to get it to work (ASUS Prime X370 Pro) to no avail. Eventually I bought this for $10 and it worked immediately with no drivers or setup: https://www.amazon.com/gp/product/B072BMG9TB/ref=oh_aui_detailpage_o02_s00?ie=UTF8&psc=1
One question for starters, I am using a Radeon R9 280x with no graphics injection. If I put my Ryzen build to sleep, it changes power states correctly. When Powered back on, the monitors don't turn on. I don't know if this is related to the GPU, or just an issue in general, but in any case I would appreciate any help!
Hi, this was supposed to be weekend project,well not so much now, I'm throwing in the towel... for now. I have a perfectly working sierra box, network, video, etc. BUT I can't get clover to boot from the HD without using the flash drive. I have tried moving kelts around, multibeasts tweaks, you name it, can anybody see what I'm missing?
Brand American Megatrends Inc.
video: ATI AMD RADEON HD 6450
mobo:ASRock B75M-DGS R2.0 (CPUSocket)
Intel Core i3 2100 @ 3.10GHz 39 °C
Sandy Bridge 32nm Technology
please look at my attached jpegs, help appreciated!! (sorry can't get them rotated)
This is what i have done so far to get my SP3 i5 256 working. Booting from SSD in USB3 Case as I am testing I do not want to mess with my Internal SP3 SSD.
The build in not perfect but works. still early days.
chat with us and share https://gitter.im/julianjc84/jc84_SP3_hookups
I require the use of USBInjectAll.kext to fix the USBports for USB wifi adapter. Seems to only effect me with USB booting. OS,s installed on internal SSD seem to not have usb issue.
minor video artifacts once system is booted below menu bar.
What work and work great
Intel 4400HD QI QE, Accelerated Video
Sound build in.
Touch, Single input http://monstersoft.com/sp3/VoodooI2C.kext.5ms.zip do not use DSDT
Surface Pro 4 Touch Cover, Single Input
Hello, I have recently update my customac from Yosemite to El Capitan.
I have successfully boot up El Capitan using Enoch bootloader. After boot up in El Capitan my Wi-Fi stopped working and battery is not showing in menu bar. Except this two function my customac has no other problem. I have tried to find new kext for this two function but unable to find single one of working kext. My laptop configuration is given below :-
System Model :- Lenovo Z560. Bios Version :- Unlocked InsydeH2O. Processor :- Core i5 M480 @ 2.67 GHz. RAM :- 4 GB DDR 3. Graphics :- NVidia GeForce 310M (working fine with NVclox kext). Audio :- Conexant CX20671 ( working fine with patched appleHDA kext). Ethernet Card :- Realtek PCIe FE Family. Wi-Fi :- Qualcomm Atheros AR9285 Wireless Network Adapter. (which is very important but not working for me).
I have attached all of my kext and extra folder which are recently used by me in El Capitan Customac, Wi-Fi details in text clipping and also CPU Z extracted text in attachment.
Any one Please! Help me. Otherwise I have to go back Yosemite again. Also thanks in advance. :yes: