Jump to content
dark_hacker

Helps to create correct dsdt for my hardware

59 posts in this topic

Recommended Posts

Advertisement

OK , i'm the friend of CHRIS :)

See attached file

for config.plist - kexts 10.13 clover - kexts in S/L/E 

for wifi i use a usb key GO-USB-N150

my laptop is an ACER ASPIRE 5733 

good hack  :thumbsup_anim:

 

Thank you. I use your config.plist as well?

Share this post


Link to post
Share on other sites

Thank you. I use your config.plist as well?

try and say 

the first time boot  you must delete in S/L/E

AppleIntelHDGraphics.kext

AppleIntelHDGraphicsGA.plugin ( if present )

and when you are on your desktop 

you install the five kexts who are in the folder S/L/E off archive

Share this post


Link to post
Share on other sites

try and say 

the first time boot  you must delete in S/L/E

AppleIntelHDGraphics.kext

AppleIntelHDGraphicsGA.plugin ( if present )

and when you are on your desktop 

you install the five kexts who are in the folder S/L/E off archive

 

 

I installed as 5 kexts on S / L / B after eleminating as the original kexts of the system. I tried with your config to boot after adding cpus = 1 ms of the system was the same with your problem with your setup was slow I got the istats and it with your config was always the blinking would appreciate and disappeared my repos config and it got good this part more holds the same problem.

Share this post


Link to post
Share on other sites

I installed as 5 kexts on S / L / B after eleminating as the original kexts of the system. I tried with your config to boot after adding cpus = 1 ms of the system was the same with your problem with your setup was slow I got the istats and it with your config was always the blinking would appreciate and disappeared my repos config and it got good this part more holds the same problem.

what is exactly your processor intel ???

Share this post


Link to post
Share on other sites

what is exactly your processor intel ???

 

Core i5 460M

 

I have not installed kexts as a one with the kext utility I pasted as 5 kexts in S / L / E and then I executed the kext utility can this be?

Share this post


Link to post
Share on other sites

CPU: Core i5 460M  :D 

i think is the same that me 

but have you see that in the tuto ; Intel HD Graphics Kexts 10.12 L package is compatible with macOS High Sierra 10.13.

 

captur10.jpg

Share this post


Link to post
Share on other sites

i think is the same that me 

but have you see that in the tuto ; Intel HD Graphics Kexts 10.12 L package is compatible with macOS High Sierra 10.13.

 

captur10.jpg

He try Sierra 10.12.6 ?

Share this post


Link to post
Share on other sites

i think is the same that me 

but have you see that in the tuto ; Intel HD Graphics Kexts 10.12 L package is compatible with macOS High Sierra 10.13.

 

captur10.jpg

 

 

I'm not using 10.13 I'm on 10.12.6

Share this post


Link to post
Share on other sites

SORRY  :yes:  :yes:

 FOR SIERRA DL : Intel HD Graphics QECI Legacy 10.12.zip

And try another frame buffer 

here : http://www.insanelymac.com/forum/files/download/208-1st-gen-intel-hd-graphics-kexts/

 

 

I have tried several buffers and have always tried the same ones but I have tested the same thing. Said, download 10.13 to install and test with kexts how to me direct

SORRY  :yes:  :yes:

 FOR SIERRA DL : Intel HD Graphics QECI Legacy 10.12.zip

And try another frame buffer 

here : http://www.insanelymac.com/forum/files/download/208-1st-gen-intel-hd-graphics-kexts/

 

I do not know if you are with the idea that the graph does not work, it works with the kexts only that it does not work well it shows some distortions in some parts of the system like in the image that I put to your friend

 

the problem is this

 

https://imgur.com/UTuoIss

Share this post


Link to post
Share on other sites

I have tried several buffers and have always tried the same ones but I have tested the same thing. Said, download 10.13 to install and test with kexts how to me direct

 

I do not know if you are with the idea that the graph does not work, it works with the kexts only that it does not work well it shows some distortions in some parts of the system like in the image that I put to your friend

 

the problem is this

 

https://imgur.com/UTuoIss

you have changed your processor , the I3 was also arrandale 

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By Slice
      I successfully installed macOS 10.11.6 and Windows 7 Pro SP1 in UEFI mode on the laptop.
      I know, there are detailed guides here and on osxlatitude.com but I was not agree with them and carefully check and test every step to tune my Mac.
       
      Hardware
      Intel® Core� i5-3320M CPU @ 2.60GHz, speedstep works with Clover default settings
      Chipset Intel 7 series, no patches needed
      Video: IntelHD4000 or NVS5200M switchable in BIOS, work in both cases
      LAN; Intel 82579LM, works with IntelMausiEthernet.kext v2.2.1
      Audio: IDT 92HD93BXX, works with VoodooHDA 2.9.0.
      SDHC reader O2Micro; works with native AppleSDHC.kext with Clover Arbitrary properties.
      USB3.0 works natively if not disabled in DSDT
      PS2 keyboard and touchpad works with VoodooPS2.
      WiFi: Dell Intel WiFi was replaced by Dell DW1520, Broadcom BCM943224HMS. DeviceID=4353
      LCD Screen 1366x768
      BIOS A12. Initially was A02. Then I flashed A23 and found it is quite bad. The screen is full of artefacts. Flash A12 and all is OK. Not tested other versions.
      For some reason BIOS can switched from Intel to Nvidia by itself so I have to do my solution working independent on this state.
       
      WiFi
      It is not working OOB although it has DeviceID known to Apple. The reason is WhiteList in the driver.
      I set MacModel as MacBookPro10,1 while the WiFi will work on MacBookAir. I make a patch in Clover.
      As well a patch for channels.
      I deleted a kext Brcm4331 because it has the same DeviceID. Let kext Brcm4360 to work alone.
       
      VideoCards
      In Bios we can set Optimus = Enable/Disable
      If Enable then we have two videocards Intel first and Nvidia second. In this case additional SSDT-3.aml will switch off Nvidia.
      If Disable then we have only Nvidia card. It will work if Board-ID taken from iMac13,2.
      But here there is contradiction with WiFi with required Board-ID from MacBookAir.
      So I take MacModel as MacBookPro10,1 which is most close by CPU IvyBridge.
      Set BoardID like iMac13,2 to make Nvidia working.
      Patch BoardID in Brcm4360 to make WiFi working.
      Now I have
      Inject->
      ->Intel=YES
      ->Nvidia=YES
      and SSDT-3.aml in ACPI\patched folder. This SSDT will switch off Nvidia if Intel card ON.
      For Intel graphics there is a patch against 8 apples at start.
      This Nvidia 5200 is Fermi and works in ElCapitan.
       
      Brightness
      No special kexts.
      The brightness controlled by keys F1,F2 and slider in Control Panel in both case Intel or Nvidia. Details here  #72 
       
      DSDT and SSDT
      This is very long story and finally I have working sleep in both cases Intel or Nvidia.
       
      Sensors
      I use my HWSensors3 with FakeSMC 3.5.2.
      I got monitoring:
      CPU temperature
      GPU temperature
      GPU main frequency
      GPU shader frequency
      Battery state % full, time to charged or time to empty.
      Battery voltage dinamically.
      Battery amperage dynamically. I can see it changes on heavy games.
      HDD temperature.

       
      Audio
      I like VoodooHDA and have no problems with it.
      The sound is clear, loud, and switchable between internal speaker and headphone.
      Mic is working.
       
      Bluetooth
      Just tested with BTFirmwareUpdate.kext and it works in 10.11.6. I not needed it so switched off by wireless switch at right side.
      For 10.13.6 there is other kext BRCMInjector.
       
      Keyboard, Touchpad and Touchstick
      Post #14
      I made my fork of the VoodooPS2 driver, take here sources and release version
      https://github.com/SergeySlice/VoodooPS2-for-ALPS
       
      My config, ACPI files and kexts are in attachment.
      05.12.2017
      EFI.7z
       
      EDITED:
      Better DSDT in the post #6.
      Sleep working even when AC inserted.
       
      EDITED 06.12.2018
      Now I have HighSierra and this is my EFI folder. Note, HighSierra is possible only with Intel graphics (Optimus is enabled in BIOS)
       

       
       
      Welcome to discussion!
      EFI-E6430.7z
      BRCMInjector.kext.zip
    • By MaLd0n
      ---INSTALLATION TUTORIAL---
       
      ---Original Post---
      https://olarila.com/forum/viewtopic.php?f=45&t=9172
       
      ---USB---
      https://pikeralpha.wordpress.com/2016/07/13/simple-skylake-usb-fix-no-kexts-required/
       
      ---CLOVER FOLDER---
       
      CLOVER.zip
       
       
      --MOBO
      GigaByte Z390 M Gaming



      --PROCESSOR
      Intel Core i9-9900K


      --COOLER
      CoolerMaster MasterLiquid ML120R RGB


      --MEMORY
      Corsair Dominator Platinum 16GB (2 x 8GB)


      --GPU
      Sapphiretech Radeon RX 590 8 GB GDDR5


       
      --SSD
      Samsung 970 EVO NVMe M2 Flash Drive


      --POWER SUPPLY
      EVGA 750 N1, 750W


      --WIRELESS
      TP-Link Archer T9E


      --BLUETOOTH
      Orico BTA-403


      --CASE
      Thermaltake View 21 Tempered Glass Edition


      --DSDT Patches--
      -FIX ERRORS AND WARNINGS -FIX ACPI ERRORS -REMOVE UNUSED SCOPES / DEVICES -HIGH PRECISION EVENT TIMER -SATA SERIE 10 ID -DMAC -REMOVE 22K LINES, PROBLEMATIC and UNUSED -FIX K.P in REBOOT -NVRAM / REAL TIME CLOCK -SLPB -DARWIN / WINDOWS 2015 -XHCI -PLUGIN TYPE -HDAS to HDEF -HDEF -REAL TIME CLOCK -ARTC -IRQs -SBUS -MIKEY -BUS1 -MCHC -ALS0 -SHUTDOWN -UAR1 -LAN -FWHD -USBX -PMCR -PPMC -XSPI -GMM -IMEI -EC -PNLF -ARPT -GFX0 -NVME -DTGP -ACQUIRE MUT0 0XFFFF -OPERATION REGION GPIO -MUTEX MUT0 0x00 -EXTERNAL REFERENCES -UNKNOWNOBJ -HDMI / HDAU -FULL RENAMED DEVICES  
      --SCREENSHOTS--





























      --BruceX--
       
      --USB-C-- test with SanDisk Ultra USB-STICK 128gb


       
      -Credits and thanks to the old and new people in the community who developed patches, kexts and bootloaders!
      Slice, Kabyl, usr-sse2, jadran, Blackosx, dmazar, STLVNUB, pcj, apianti, JrCs, pene, FrodoKenny, skoczy, ycr.ru, Oscar09, xsmile, SoThOr, RehabMan, Download-Fritz, Zenit432, cecekpawon, Intel, Apple, Oracle, Chameleon Team, crazybirdy, Mieze, Mirone, Oldnapalm, netkas, Elconiglio, artut-pt, ErmaC, Pavo, Toleda, Master Chief and family, bcc9, The King, PMheart, Sherlocks, Micky1979, vit9696, vandroiy2013, Voodoo Team, Pike R. Alpha, lvs1974, Austere.J, CVad, Sampath007, onemanosx, erroruser, Jenny David, Olarila Facebook Community, Hackintosh Facebook Community and many others!
      We're all here to have fun and learn from each other!
    • By Gabigeek
      Hi everybody,
      First this is my first post on this forum so I hope Im creating a topic at the right place 
      Im french, so sorry for my bad english 
       
      So I recently made a Hackintosh Laptop (on a ROG GL553VD-DM078T )
      This laptop is based on a i7 7700HQ and a GTX1050.
      I installed MacOS Sierra using the Clover bootloader and succesfully installed  the kexts needed but one of them is causing trouble.
       
      I Broke my internal ethernet Port so I must use a USB-C ethernet dongle in order to acces the internet ( The Integrated Wifi chipset isn't compatible so that's my only way to connect.)
      Without the UsbInjectAll.kext everything works exept my laptop keyboard wich use USB (yes, the internal ASUS Aura keyboard use USB interface, not PS2 or IC2 ).
      But if I load the UsbInjectAll kext the keyboard works, but the USB-C ethernet dongle is no more recognized at all ( not even in the system report menu)
      The weird thing is that if I plug a USB stick in the USB-C port, it works, but the ethernet dongle won't.
       
      So now I have 2 options :
      -or I load the UsbInjectAll kext and I get my keyboard to work
      -or I disable the UsbInjectAll kext so i can get back my ethernet USB-C dongle to work, but no more keyboard....
       
      Can someone explain why do this happen ? Is there a way to get both The Ethernet dongle and my internal keyboard to work at the same time ?
      If Needed, I can provide more information about the hardware Used etc.
       
      Have a good Day/night 
×