Jump to content

16 posts in this topic

Recommended Posts

Hello guys!

I Have my hackintosh finally working with 12.5.

All seems to work, but dual screen is not working at all.

 

There are 2 vga monitors connected  in Displayport and HDMi (with connectors)

 

I can use both only if first I boot with one of them.

then in desktop I can plug the other monitor and works.

 

If I boot with both monitors connected , the hackintosh boot showing image in only one monitor, and after of the apple screen it stops showing image  (only colors)

 

The components are:

-Asus Z170-A

-i7 7770k (Kabylake)

-32 GB Ram 2400 DDR4 GSkill Ripjaws

-Kingston SSD.

 

What could happen?

 

Thanks you so much!

Share this post


Link to post
Share on other sites
Advertisement

I'd recommend you do the following:

1) when both displays are operational, take an IOReg dump with IORegistryExplorer and lookup the ports and connector type for both outputs

2) take a note of the layout-id used to obtain graphics acceleration

3) apply patch to the graphics Framebuffer (binary mod of the kext file or Clover on-the-fly patch) to get each desired output port configured with the target settings

 

There's probably a conflict of ports in your initial case.

Share this post


Link to post
Share on other sites

Hi! Thanks for your reply!

Im new with ioreg. And im trying to learn how it works.

could you help me to find graphic lines in my ioreg?

 

after of that, how can I apply the changes???

 

here is my ioreg:

iMac.zip

 

Thanks you for your help!!!

Share this post


Link to post
Share on other sites

Your iGPU is found in IOReg as device GFX0 located at address 0x00020000 (GFX0@2 under PCI0@0). IOReg shows iGPU PCI id 8086:5912 and model "Intel HD Graphics 630" (in Hex) which is totally inline with Intel ARK info for i7-7770K CPU. IOReg also shows that you're using layout-id 0x19120000.

post-851564-0-81979000-1497616416_thumb.png

 

IOReg info shows a display (labelled display0) under 2 x framebuffers: FB@1 and FB@2,

post-851564-0-20237200-1497616430_thumb.png post-851564-0-66552100-1497616438_thumb.png

 

In terms of attached displays, IOREg shows:

  • FB@1 -> connector type 0x00040000 (i.e. DP output) + port number 0x05
  • FB@2 -> connector type 0x00040000 (i.e. DP output) + port number 0x06

 

Connector types are of the following range:

  • 0100 0000 for VGA
  • 0200 0000 for LVDS (built-in LCD of laptops)
  • 0400 0000 for eDP (built-in LCD of laptops)
  • 0002 0000 for DVI
  • 0004 0000 for DP
  • 0008 0000 for HDMI

 

At this stage, all you would normally need to do would be to identify which output really is DP and which really is HDMI. How? Simple: whilst running IORegistryExplorer, disconnect one of your external screen, refresh IORegistryExplorer and check which port has disconnected (-> no display0 seen under the FB@x).

 

You may then patch your framebuffer kext accordingly so that the system knows what gets attached to each port. To patch the framebuffer kext, you would open its binary file (found in Contents/MacOS folder of the kext package) with a Hex editor (apps such as 0xED or HexFiend for instance), look for the 19120000 layout and edit the code for the port as required (change DP connector type 00 04 00 00 to HDMI connector type 00 08 00 00 to begin with). In your case, we're talking about Skylake framebuffer kext, i.e. AppleIntelSKLGraphicsFramebuffer.kext found in /S/L/E.

 

I've no Skylake of Kaby Lake platform and have not looked much into patching this specific framebuffer but, building on previous SNB/Capri/Azul frambebuffer experience, I'm pretty sure you need to look at patching the following layout in the kext binary file:

00001219 00000000 4F880800 00000000          // layout 19120000 ...
01030303 00002002 00005001 00000060
6C050000 6C050000 00000000 00000000
FF000000 01000000 20000000 01050900
00040000 87010000 02040A00 00040000
87010000 03060A00 00040000 87010000
0F110000 00000000 00000000 00000000
00000000 00000000 00000000 00000000
00000000 00000000 00000000 00000000

`

In the same fashion as connector types, port numbers fall within the following typical range:

  • 0000 ... for framebuffer #0 / port #0
  • 0105 ... for framebuffer #1 / port #5
  • 0204 ... for framebuffer #2 / port #6
  • 0306 ... for framebuffer #4 / port #7

 

You will therefore play with the code starting by 0105 (port #5) or 0204 (port #6), i.e. :

01050900 00040000 87010000          // port #5, priority 09, DP output
02040A00 00040000 87010000          // port #6, priority 0A, DP output

and, for instance, if port #6 is HDMI, you would try and change the line starting by 0204 to:

02040A00 00080000 87010000          // port #6, HDMI output

to reflect the correct HDMI connector type. The priorities differ so you should be Ok on that front.

 

Can't guarantee 100% it'll work, but I'm sure this would put you on the correct path.

Share this post


Link to post
Share on other sites

Oh , wow ! It's difficult! Let me try to learn more about it. Thanks you so much!

 

 

Enviado desde mi iPhone utilizando Tapatalk

Share this post


Link to post
Share on other sites
On 6/16/2017 at 2:34 PM, Hervé said:

Your iGPU is found in IOReg as device GFX0 located at address 0x00020000 (GFX0@2 under PCI0@0). IOReg shows iGPU PCI id 8086:5912 and model "Intel HD Graphics 630" (in Hex) which is totally inline with Intel ARK info for i7-7770K CPU. IOReg also shows that you're using layout-id 0x19120000.

post-851564-0-81979000-1497616416_thumb.png

 

IOReg info shows a display (labelled display0) under 2 x framebuffers: FB@1 and FB@2,

post-851564-0-20237200-1497616430_thumb.png post-851564-0-66552100-1497616438_thumb.png

 

In terms of attached displays, IOREg shows:

  • FB@1 -> connector type 0x00040000 (i.e. DP output) + port number 0x05
  • FB@2 -> connector type 0x00040000 (i.e. DP output) + port number 0x06

 

Connector types are of the following range:

  • 0100 0000 for VGA
  • 0200 0000 for LVDS (built-in LCD of laptops)
  • 0400 0000 for eDP (built-in LCD of laptops)
  • 0002 0000 for DVI
  • 0004 0000 for DP
  • 0008 0000 for HDMI

 

At this stage, all you would normally need to do would be to identify which output really is DP and which really is HDMI. How? Simple: whilst running IORegistryExplorer, disconnect one of your external screen, refresh IORegistryExplorer and check which port has disconnected (-> no display0 seen under the FB@x).

 

You may then patch your framebuffer kext accordingly so that the system knows what gets attached to each port. To patch the framebuffer kext, you would open its binary file (found in Contents/MacOS folder of the kext package) with a Hex editor (apps such as 0xED or HexFiend for instance), look for the 19120000 layout and edit the code for the port as required (change DP connector type 00 04 00 00 to HDMI connector type 00 08 00 00 to begin with). In your case, we're talking about Skylake framebuffer kext, i.e. AppleIntelSKLGraphicsFramebuffer.kext found in /S/L/E.

 

I've no Skylake of Kaby Lake platform and have not looked much into patching this specific framebuffer but, building on previous SNB/Capri/Azul frambebuffer experience, I'm pretty sure you need to look at patching the following layout in the kext binary file:


00001219 00000000 4F880800 00000000          // layout 19120000 ...
01030303 00002002 00005001 00000060
6C050000 6C050000 00000000 00000000
FF000000 01000000 20000000 01050900
00040000 87010000 02040A00 00040000
87010000 03060A00 00040000 87010000
0F110000 00000000 00000000 00000000
00000000 00000000 00000000 00000000
00000000 00000000 00000000 00000000

`

In the same fashion as connector types, port numbers fall within the following typical range:

  • 0000 ... for framebuffer #0 / port #0
  • 0105 ... for framebuffer #1 / port #5
  • 0204 ... for framebuffer #2 / port #6
  • 0306 ... for framebuffer #4 / port #7

 

You will therefore play with the code starting by 0105 (port #5) or 0204 (port #6), i.e. :


01050900 00040000 87010000          // port #5, priority 09, DP output
02040A00 00040000 87010000          // port #6, priority 0A, DP output

and, for instance, if port #6 is HDMI, you would try and change the line starting by 0204 to:


02040A00 00080000 87010000          // port #6, HDMI output

to reflect the correct HDMI connector type. The priorities differ so you should be Ok on that front.

 

Can't guarantee 100% it'll work, but I'm sure this would put you on the correct path.

 

my external monitor is plugget on the only hdmi but System Profiler show this like DP port. I tried to patch the framebuffer but it doens't work, how to?

debug_30585.zip

Schermata 2018-08-13 alle 11.00.03.png

Share this post


Link to post
Share on other sites

Your IOReg shows your external display connected to port #5 on DP connector-type 0004 0000, i.e. your patch seems ineffective.

 

Looking at your posted Clover config, you've applied the following patches to SKL layout-id 19160000:

                   \/
Before: 01050900 00040000 87000000
After:  01050900 00080000 87000000
                   /\

and

                   \/
Before: 02040A00 00040000 87000000
After:  02040A00 00080000 87000000
                   /\

I could not see any mistake in the patches, whether in the binary code or the kext name, though I'm wondering if the version of Clover you use requires the "com.apple.driver." prefix or not... You could try without and re-check IOReg.

 

This being said, since port #5 is identified as the connected port, you only need to patch that port. As such, you could revise your patch as follows:

                                                                                                                                           \/
Find:    0000161900000000E381080000000000010303030000200200005001000000606C0500006C0500000000000000000000000008000200000098000000010509000004000087010000
Replace: 0000161900000000E381080000000000010303030000200200005001000000606C0500006C0500000000000000000000000008000200000098000000010509000008000087010000
                                                                                                                                           /\

Where we basically only replace 01050900 00040000 by 01050900 00080000 in layout 0x19160000 and leave port #6 untouched,

 

If that still does not work, we can try to modify the priority byte too and the patch would be:

                                                                                                                                     \/    \/
Find:    0000161900000000E381080000000000010303030000200200005001000000606C0500006C0500000000000000000000000008000200000098000000010509000004000087010000
Replace: 0000161900000000E381080000000000010303030000200200005001000000606C0500006C0500000000000000000000000008000200000098000000010512000008000087010000
                                                                                                                                     /\    /\

where we basically replace 01050900 00040000 by 01051200 00080000 in layout 0x19160000. Why? Well, because that's the value I required on my Haswell system for HDMI to work...

 

Rebuild your cache before rebooting. If the patch remains ineffective, we can try a direct binary modded kext with an increased kext version that we'll place in /L/E for caching in replacement of the Clover on-the-fly patch.

Edited by Hervé

Share this post


Link to post
Share on other sites

Many thanx for reply Hervé!

 

I tried what you wrote to me ... it seems to work, but when I connect the external monitor it goes back to 00040000 .... I do not understand why! Look Yourself in the attacched.

 

I ask you something else, you can tell me why if you imposed as SMBIOS MacBook Pro 13.3 the external monitor is not right, while with the other SMBIOS works (example, works with Macbook pro 13.1 - 13.2 - 9, 1)

MacBook Pro with HDMI.ioreg

MacBook Pro No connection HDMI.ioreg

Share this post


Link to post
Share on other sites

Looking at your IORef "before" I see that you still patched both ports #5 and #6 when I said #5 should suffice... Anyway, it seems to work now, even though connector-type switches to DP for some reason when you connect the HDMI cable as seen in IOReg "after". Dp you use a HDMI cable all the way? I mean HDMI cable at the output of the computer and at the entry of the external monitor? No HDMI-to-DP or DP-to-HDMI adapter involved?

 

With regards to lack of external monitor with MBP13,3 SMBIOS, that'll be due to the specs of each model. MPB13,3 is dual graphics (Intel iGPU + AMD Radeon) where the others are Intel iGPU only. You can check the specs of the various models at everymac.com.

Edited by Hervé

Share this post


Link to post
Share on other sites

 

I use a Mini HDMI to HDMI adapter, as the output port is HDMI only. Now I correct and put the patch 1. Thanks for the help. Regarding the MacBook Pro 13.3 maybe I have not explained well. If I use this SMBIOS and connect an external monitor, nothing is detected but only the integrated notebook screen works. This model has two Thunderbolt ports as video outputs, so I ask you where I need to change to change from Thunderbolt to HDMi and activate video output

 

You need some output files from my system?

Edited by gigibatt

Share this post


Link to post
Share on other sites

It seems you misunderstand... You patch framebuffers to match your own hardware, not to pretend/fake hardware you don't have. If your output port is HDMI, that's what you have to patch the FB for.

 

I'm pretty certain the reason why connector-type changes to DP is due to your mini-HDMI output port. Maybe it's a mini-DP port, not mini-HDMI. Anyway, if you're getting video output on your HDMI monitor, I guess that all is Ok, isn't it?

 

Edited by Hervé

Share this post


Link to post
Share on other sites

mmm ok...

 

I do not know any non-Apple notebook with two thunderbolt outputs. So you're telling me that it makes no sense to use the SMBIOS MacBook Pro 13.3 because there are no notebooks with thunderbolt outputs? I thought it was possible to simply say to use an HDMI port instead of a thunderbolt ....

Share this post


Link to post
Share on other sites

No, that's not what I'm saying, it's not just a matter of output ports; as I said MBP13,3 is dual graphics with Intel iGPU + AMD Radeon dGPU. Some output may be directly wired to the dGPU. I don't know.

 

Use the SMBIOS of MBP13,1 or 13,2 if that's what works for your system. It's a Hackintosh, not everything works as on a real Mac you know...

Edited by Hervé

Share this post


Link to post
Share on other sites

 

Thank you for what you taught me and for the time you spent for me!

 

the last question: Rehab says the lags / pauses / unresponsiveness shortly after boot is caused from unused 
connectors. Do you think I have to remove connectors from the ig-platform? How to?
Edited by gigibatt

Share this post


Link to post
Share on other sites
On 8/13/2018 at 11:01 PM, Hervé said:

I would leave things as they are.

Herve! I have a pc clone of the notebook of which I asked you above. The only problem I have is that if I start with the external 
monitor connected to the HDMI output, the internal monitor remains black and only the external one works. Can you tell me what I 
have to do for you? Mount an Intel HD620 (framebuffer 59160000)

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By kylon
      A big thanks to wegface for teaching me a lot of things.
       
       
      Tested on Catalina 10.15.4 and Clover EFI 5104 (Catalina Patcher)
       
      Not Working:
      - realtek sd card reader (pm me if you have a fix)
       
      Notes:
      **CPU patches are disabled, if you are using a locked BIOS you must enable them**
       
      Clover EFI:
      - Install it in UEFI Mode and change your hdd partition table to GPT.
      - You will be able to install ANY OS in EFI mode, even if this pc does not support EFI at all! (No guide available for this)
       
      You will need:
      My unlocked BIOS (OPTIONAL) (here) Latest Clover config from CCE Bank (here) (asus k53sj-kylon) Rehabman Voodoo PS2 Controller (here) acidanthera AppleALC (here) acidanthera Lilu (here) acidanthera VirtualSMC (here) acidanthera SMCBatteryManager (here) acidanthera SMCLightSensor (here) acidanthera WhateverGreen (here) Mieze Realtek RTL8111 (here)
    • By kushwavez
      A really good motherboard with macOS compatible bult-in Wifi & Bluetooth

      ASUS Z170-Deluxe (with Wifi)
      BIOS: v3801
      CPU: i7-6700K 4.0 to 4.2 GHz (w/o OC)
      RAM: 1x 16 GB Corsair DDR4 2400 MHz
      GPU: Intel HD 530 (Headless) & ASUS Radeon RX 5700 OC 8 GB
      Audio: ALC 1150
      Ethernet: I219V2, I211-AT
      WiFi & Bluetooth: Broadcom BCM94360HMB Half-Mini-PCI-E
      More Specs: https://www.asus.com/Motherboards/Z170-DELUXE/specifications/
       
      Catalina 10.15.4 - Windows 10
      What is working:
      BCM94360HMB Wifi and Bluetooth AirDrop, Handoff, FaceTime, Messages, App Store, iCloud, etc. Intel HD 530 (QE/CI tested, but now I'm using it in headless) Sleep RX 5700 (QE/CI with 2 1080p monitors connected) Sound USB Ports Two Ethernet ports macOS with a light OC (4.12 GHz - 4.5 Ghz, XMP, ASUS optimal) No problem so far ASUS HyperKit with a KINGSTON NVMe SSD - 250 GB  
      What is not working:
      -  
       
      Not tested:
      VideoProc says that Hardware Decoding\Encoding is fully supported and enabled on both HD 530 and RX 5700 but I didn't test it Thunderbolt (no equipment)  
      Issues:
      None  
      BIOS Settings:
      Boot\CSM (Compatibility Support Module): Launch CSM: Disabled Boot\Secure Boot: OS type: Other OS Secure Boot State: Disabled Advanced\System agent (sa) Configuration: VT-d: Enabled Graphics Configuration: Primary Display: Auto iGPU Multi-monitor: Enabled RC6(Render Standby): Enabled DVMT Pre-Allocated: 128M Advanced\PCH Storage Configuration: SATA Mode Selection: AHCI HyperKit: Enable (if you have NVMe SSD with ASUS HyperKit) Advanced\CPU Configuration: Intel Virtualization Technology: Enabled CPU- Power Management Control: Intel SpeedStep: Enabled CPU- C-States: Enabled Intel SpeedShift: Enabled  
      Getting ready for installation:
      Download the bootpack (Clover v5106): Click here -> asus-z170_clover_5107.zip  
      Installation:
      Create an installer with any method you know (- Mac: createinstallmedia - Windows: Transmac, Vmware, Win32diskimager) Copy my Clover folder to the USB's EFI folder Boot with the Installer USB If you have any problem (kp or freeze) boot with config_debug.plist to see what causes the issue  
      Post Installation:
      Download Clover Configurator and generate a new Serial Number for yourself  
      Some pictures:
       

       




       
       
       
      Catalina & Windows 10 Dual-Boot (clean install, on one drive):
       Boot into your Mac installer, Create 2 partitions in GUID table (1 for Win (I used FAT32 but I think it doesn't matter what you choose), 1 for Mac)
       Install Mac, boot with your USB, mount your EFI partition (use terminal or an EFI mounter app), create an EFI folder (if there is no folder), copy the CLOVER folder I attached to the EFI folder, restart
      Boot into your Win installer, Format the partition you created for Win, install. 
      Now, it's automatically booting into Windows. To use Clover open cmd in administrator, type: 
      bcdedit /set {bootmgr} path \EFI\CLOVER\CLOVERX64.efi  
      You're done! It will booting into Clover when you start the system, and you can select Win or Mac (or another OS if installed on a 3rd partition).
       
      IF YOU GETTING ERRORS DURING WINDOWS INSTALLATION (could not be formatted, etc):
      Make sure you have GPT partitions, and GPT (UEFI) installer, also disconnect all external storage drives (except the installer USB)  
      Mounting EFI from Windows:
      Open cmd in administrator mode and type: mountvol b: /s (This will mount your EFI) Open Total Commander or Explorer++ in administrator mode to manage EFI mountvol b: /d (This will unmount your EFI)  
      Notes:
       
      2020.03.26: Updated to 10.15.4 -> Updated WhateverGreen, Lilu -> Updated Clover to v5107
      2020.03.23: Removed "EmuVariableUefi.efi" -> deleted, caused false nvram map, now it's native, updated Clover to v5106
      2020.02.11: Updated to 10.15.3 -> No problem when/after installing
      2020.01.19: Added ASUS HyperKit NVMe SSD to the "What is working" list
      2020.01.12: Tested system with OC, added more informations to BIOS settings
      2020.01.11: Added SmallTreeIntel82576.kext for 2nd Ethernet, Tested Ethernet ports
      2020.01.11: First upload
       
    • By ludufre
      Installing macOS Catalina 10.15.4 on Asus VivoBook S400CA
       
       
      There are several versions of this laptop.
       
      These are the versions I've seen so far:
      - S400CA-BRA-CA206H = i3-2375M with ALC269VB
      - S400CA-BRA-CA178H = i5-3317U with VT1802P
       
      I believe that all models are practically identical except the variations i3 and i5 that have particularities, because one is Sandy Bridge platform and another Ivy Bridge.
       

      Changelog:
       
      03/24/2019 20:35h GMT-0
      - Added update 10.15.4 instructions.
       
      12/11/2019 04:35h GMT-0
      - Added update 10.15.2 instructions.
       
      11/11/2019 04:41h GMT-0
      - Merged Core i3 and i5 config.plist.
      Same SMBIOS now. Core i3 version need to remove: Devices - Properties - PciRoot(0x0)/Pci(0x2,0x0). - Just one USBPorts.kext now, since SMBIOS are same. 
       
      11/10/2019 20:41h GMT-0
      - Updated USB 3.0 injection. (Removed USBInjectAll.kext and SSDT-UIAC.aml and added USBPorts.kext)
      - Replaced AtherosE2200Ethernet.kext with version 2.3.0 RELEASE. (Previously was DEBUG build)
       
      11/10/2019 00:22h GMT-0
      - Added Battery's DSDT patch.
      - Fixed USB 3.0. (Replaced USB's DSDT patch, removed FakePCIID.kext and FakePCIID_XHCIMux.kext and added SSDT-EC.aml and SSDT-UIAC.aml)
      - Updated config.plist. (Removed PNP0C09 to PNPFFFF, not needed with SSDT-EC.aml)
       
      11/08/2019 14:33h GMT-0
      - First version.
       
      What works and what does not
       
      Core i3 Version specific
      - Processor: Intel Core i3-2375M ->  Work. All SpeedStep stages.
      - Video Card: Intel HD3000 ->  Work. QE/CI without Metal. (additional step bellow)
      - Audio: ALC269VB ->  Work. But no earphone. (more details)
       
      Core i5 Version specific
      - Processor: Intel Core i5-3317U ->  Work. All SpeedStep stages.
      - Video Card: Intel HD4000 ->  Work. QE/CI and Metal.
      - Audio: VT1802P ->  Work.
       
      Common
      - Chipset: Intel HM76 ->  Work.
      - HDMI ->  Work.
      - VGA ->  Not work. Normal.
      - WiFi/Bluetooth: Intel AC 3160 ->  Not work. Replaced with DW1560 / AW-CE123H.
      - Ethernet: Intel AR8161 ->  Work.
      - Card Reader: Unknow ->  Not work.
      - Keyboard and Touchpad ->  Work.
      - FN keyboards keys ->  Not work yet.
      - Webcam ->  Work.
      - Battery ->  Work.
      - Touch screen ->  Not work.
      - USB3.0 ->  Work.
      - Sleep ->  Work.
      - Airdrop, Handoff and Continuity ->  Work after replaced wireless.
      - Instant Hotspot ->  Not work even after replaced wireless.
       
       
      Todo
       
      - Make earphone work in Core i3 version.
      - Fix FN keyboard keys.
      - Convert DSDT patches to hotpatch.
      - Make touch screen work.
      - Make card reader work.
      - Make trackpad appear in System Preferences
       
       
      What you need to install

      - Running install of macOS
      - One USB flash drive of 8GB or bigger
      - macOS Catalina install app
      - Clover EFI
      - Clover Configurator
      - Some KEXTs and SSDT patches


      How create create the install flash drive
       
      Prepare install flash drive

      Format the flash drive with GUID partition mapping and name it "Install".

      - Open Disk Utility.
      - Click in View, then "Show All Devices".
      - Select the destination flash drive, then Erase.
      - Name: Install, Format: Mac OS Extended (Journaled) and Scheme: GUID Partition Map
       
      Create install flash drive

      Open terminal and run this command:
      sudo /Applications/Install\ macOS\ Catalina.app/Contents/Resources/createinstallmedia --volume /Volumes/Install --nointeraction This will take about 30 minutes.
       


      Install bootloader

      Download the CloverEFI from official repository (used 5098) and install only with these options on "Install macOS Catalina":
       
      - Install for UEFI booting only
      - Install Clover in the ESP
      - UEFI Drivers - Recommended Drivers - FSInject (I still don't know if it's really necessary)
      - UEFI Drivers - File System drivers - ApfsDriverLoader (Support to APFS partitions)
      - UEFI Drivers - File System drivers - VBoxHfs (Support HFS/HFS+ partitions)
      - UEFI Drivers - Memory fix drivers - AptioMemoryFix (Fix the memory management of de UEFI/BIOS)
      - UEFI Drivers - Additional drivers - CsmVideoDxe
       
      FileVault 2
       
      If you plan to use FileVault 2, you need to download additional drivers, since what comes with Clover is not up to date and use VirtualSMC instead of FakeSMC.
      Follow instructions bellow:
       
      From current Clover installation, check these options to USB keyboard/mouse work on password screen:
      - UEFI Drivers - Human Interface Devices - UsbKbDxe
      - UEFI Drivers - Human Interface Devices - UsbMouseDxe
       
      After Clover install will be created a partition named EFI and mounted in Desktop. Usually the path is /Volumes/EFI/.
       
      Download the versions 2.1.0 and 2.0.9 of AppleSupportPkg from: https://github.com/acidanthera/AppleSupportPkg/releases
      We need the last version of AppleGenericInput.efi that is inside 2.1.0 and last version of AppleUiSupport.efi that is inside 2.0.9.
      OR download attached bellow.
       
      Put in /Volumes/EFI/EFI/CLOVER/drivers/UEFI/
       
      That's it! FileVault 2 will work without problems.
       

       
       
      Make things works
       
      After Clover install will be created a partition named EFI and mounted in Desktop. Usually the path is /Volumes/EFI/.
       
      - Replace the /Volumes/EFI/EFI/CLOVER/config.plist with mine attached below according to your processor version.
      - Put all SSDT-*.aml attached below in /Volumes/EFI/EFI/CLOVER/ACPI/patched/
       
      Generate your Serial, MLB and SmUUID
       
      - Open the replaced config.plist with Clover Configurator (used 5.7.0.0)
      - Go to SMBIOS, click few times in "Generate New" in Serial Number and SmUUID.
       
      Core i3 version:
      - Go to Devices - Properties.
      - Remove: PciRoot(0x0)/Pci(0x2,0x0).
       
      Core i5 version:
      - Remove: /Volumes/EFI/EFI/CLOVER/ACPI/patched/SSDT-PWR.aml
       
      Copy the Clover Configurator to flash drive because you will need later.
       
      Download those Kexts and put in /Volumes/EFI/EFI/CLOVER/kexts/Other/
       
      - Download the VirtualSMC.kext, SMCProcessor.kext, SMCBatteryManager.kext and UEFI driver (put VirutalSmc.efi inside /Volumes/EFI/EFI/drivers/UEFI/). I used the version 1.0.9.
      - Download the Lilu.kext from here. I used the version 1.3.9.
      - Download the VoodooPS2Controller.kext from here. I used version 2.0.4.
      - Download the AtherosE2200Ethernet.kext from here. I used the version 2.3.0 compiled from source (attached below), but the release 2.2.2 works too.
      - Download the AppleALC.kext from here. I used the version 1.4.3.
      - Download the WhateverGreen.kext from here. I used the version 1.3.4.
      - Download the USBPorts.kext attached bellow to properly inject USBs.
       
       
      Keyboard swap Command with Option (optional)
       
      - If you prefer, you can swap Command and Option keys, to map Win Key - Command and Alt - Option.
      - Change /Volumes/EFI/EFI/CLOVER/OEM/S400CA/UEFI/kexts/10.15/VoodooPS2Controller.kext/Contents/PlugIns/VoodooPS2Keyboard.kext/Contents/Info.plist:
      <key>Swap command and option</key> <true/> to:
      <key>Swap command and option</key> <false/> Or, download the version 2.0.4 already adjusted attached bellow.
       
       
      Wifi and Bluetooth (DW1560 / AW-CE123H)
       
      After replaced the wireless card. Download those Kexts and put in /Volumes/EFI/EFI/CLOVER/kexts/10.15/
       
      - Download the AirportBrcmFixup.kext from here. I used the version 2.0.4. (To enable Wireless)
      - Download the BrcmBluetoothInjector.kext, BrcmFirmwareRepo.kext and BrcmPatchRAM3.kext from here. I used the version 2.5.0. (To enable Bluetooth)
      - Download the BT4LEContinuityFixup.kext from here. I used the version 1.1.4. (To enable Handoff and Continuity)
       
      Keep in mind that the bluetooth kexts are currently in development and the official releases will be available in future in the repository: https://github.com/acidanthera/BrcmPatchRAM/releases
       
      Now you can start the installation without problem (I guess).
       
       
      How install
       
      UEFI Setup Configuration and Installation

      UEFI configuration
       
      My BIOS is the latest: 210
       
      - Shutdown and insert the flash drive.
      - Power on with F2 pressed to enter BIOS setup.
      - Change value: Advanced - Intel Virtualization Technology to DISABLED
      - Change value: Advanced - Intel(R) Anti-Theft Technology Configuration to DISABLED
      - Save & Exit Setup (F10)
       
      - Now, hold the ESC
      - In the list, select your flash drive.
      - Choose the flash drive (white icon).
       
      The installer will start. 
      
      Format destination disk

      Format the disk with GUID partition mapping and name it "Macintosh".

      - Select Disk Utility in the list, then press Continue.
      - Click in View, then "Show All Devices".
      - Select the destination Disk, then Erase.
      - Name: HD, Format: APFS and Scheme: GUID Partition Map

      Close Disk Utility.
      
      Select "Install macOS", then Continue.
      Follow instructions in screen.

      After install

      After first part install the system will reboot. Maybe you have to press ESC again and select the flash drive.
       
      Choose the internal disk (gray hdd icon) if not already selected.

      The second part of the installation will begin. This will take 16 minutes.
       

      Post installation
       
      Bootloader

      When the second part of install finish, the system will reboot again.

      After performing the user initial setup and go to the desktop, you need to make the system disk bootable.

      Open the Clover Configurator from flash drive that you copied before.

      Mount and open the flash drive EFI partition. (Inside Clover Configurator, Mount EFI -> Select flash drive in Efi Partitions list -> Mount Partition -> Open Partition)
       
      Copy the EFI folder to desktop.
       
      Go back to Clover Configurator, unmount the EFI partition of the flash drive and mount and open the EFI partition of internal disk.
       
      Move the EFI folder from Desktop to EFI partition of the internal disk.
       
      Eject the flash drive.
       
      Move all Kexts from EFI partition of internal disk to /Library/Extensions and make kext cache, with those commands in Terminal:
      sudo mv -R /Volumes/EFI/EFI/CLOVER/kexts/10.15/* /Library/Extensions/ sudo chmod -R 755 /Library/Extensions sudo chown -R root:wheel /Library/Extensions sudo kextcache -i / Restart the system.
       
      If you go directly to BIOS you have to add Clover entry manually:
       
      - Go to "Boot" and press "Add New Boot Option".
      - Select "Add boot option", write CLOVER and press Enter.
      - In "Select Filesystem", choose the option that contains "HD". Like "PCI(1F|2)\DevicePath(Type 3, SubType 12)HD(Part1,Sig2a0127c1-ea5d-44d3-8967-57e59c1f0e3b)".
      - Select "Path for boot option", write EFI\BOOT\BOOTX64.efi and press Enter.
      - Select "Create" and press enter.
      - Go to "Save & Exit" and select "Save Changes and Exit".
       
      Intel HD 3000 - Core i3 version only
       
      If you have the i3 version with HD 3000 iGPU you have to do an additional step:
       
      - Download latest Legacy Video Patch from: https://github.com/chris1111/Legacy-Video-patch/releases
      - Always use the version compatible with your current Catalina build!
      - Run the installer and reboot.
      - Graphics acceleration now works. But you'll have some rare artifacts because of lack support of Metal.
       
       
      Battery, USB & Sleep DSDT patch
       
      First we need dump current DSDT/SSDT tables:
      - Restart.
      - On Clover menu, press F4 to dump.
      - Select internal disk and start normally.
       
      Prepare files:
      - Open the Clover Configurator from flash drive that you copied before.
      - Mount and open the internal disk EFI partition. (Inside Clover Configurator, Mount EFI -> Select internal disk in Efi Partitions list -> Mount Partition -> Open Partition)
      - Navigate to EFI/CLOVER/ACPI/origin/.
      - Copy DSDT.aml to EFI/CLOVER/ACPI/patched/.
      - You'll have DSDT.aml, SSDT-EC.aml, SSDT-PWR.aml (if Core i3 version) and SSDT-PNLF.aml in EFI/CLOVER/ACPI/patched/.
       
      Apply patches to DSDT.aml:
      - Download the MacIASL from here. I used the version 2018-0507.
      - Open the DSDT.aml from patched/ with MacIASL.
      - Click in "Patch" button.
      - Paste and "Apply" each patches below.
       
      Battery patch
      #Maintained by: RehabMan for: Laptop Patches #battery_ASUS-N55SL.txt # created by RehabMan 8/12/2013 # created originally for jesselid # works for: # ASUS N55SL, BIOS rev. 204 # ASUS VivoBook series # ASUS Zenbook UX31A # ASUS UX301LA # ASUS X553E-SX399V # ASUS F501A # ASUS K55VM # ASUS U46SV, BIOS rev. 2.04 # ASUS N43 # ASUS PU500CA (90NB00F1-M01120) # ASUS N73SV # ASUS X401A-WX108 # ASUS F551CA Bios rev. 207 # ASUS S551LB VivoBook # ASUS ZenBook UX32VD # ASUS ZenBook UX32V # ASUS F550L-X455H # ASUS X53S # ASUS K550JD-XX003H # ASUS G53SX # ASUS K56CB # ASUS UX305 # ASUS N550LF (per gabberZ) # ASUS TP300LA # ASUS X200LA # ASUS TP500LA (per haimann951) # ASUS U46E (per jacopers) # ASUS N550JK (per sonicmule) # ASUS K46CM # ASUS N76-VB-T4038H (per Tamshiii) # ASUS Zenbook Pro UX501VW (per Jingu) # ASUS G751JY (per Going Bald) # ASUS S300CA (per mugen441) # ASUS F556UA-AB32 (per Jdazzle44) # ASUS UX306UA (per MaraficeEye) # ASUS N550JV (per Xracer99) # ASUS X540LA (per arg274) # ASUS X540LJ (per palash) # ASUS X550VX (per vualeks) # ASUS UX330UA (per fluxo) # ASUS UX303UB (per CyanTech) # ASUS K550JK (per m3ftwz) # ASUS TP500LB (per Archangeliques) # ASUS X556UA (per ben9923) # ASUS UX410 (per minhquang211090) # ASUS N552VW (per nicolas2121) # ASUS Vivobook NV752 (per tmazzoni) # ASUS Strix FX502VM/GL502VM (per benspoonder) # ASUS X53E (per REvandenBerg) # ASUS UX430 (per starcentral) # ... # and many others into method label B1B2 remove_entry; into definitionblock code_regex . insert begin Method (B1B2, 2, NotSerialized) { Return (Or (Arg0, ShiftLeft (Arg1, 8))) }\n end; # not really for battery, but might come in handy to read fan speed(s) into device label EC0 code_regex TAH0,\s+16 replace_matched begin TH00,8,TH01,8 end; into device label EC0 code_regex TAH1,\s+16 replace_matched begin TH10,8,TH11,8 end; into method label TACH code_regex \(TAH0, replace_matched begin (B1B2(TH00,TH01), end; into method label TACH code_regex \(TAH1, replace_matched begin (B1B2(TH10,TH11), end; into method label GFAN code_regex \(\\_SB\.PCI0\.LPCB\.EC0\.TAH0, replace_matched begin (B1B2(\\_SB.PCI0.LPCB.EC0.TH00,\\_SB.PCI0.LPCB.EC0.TH01), end; # battery EC into device label EC0 code_regex B0SN,\s+16 replace_matched begin B0S0,8,B0S1,8 end; into device label EC0 code_regex B1SN,\s+16 replace_matched begin B1S0,8,B1S1,8 end; into method label BIFA code_regex \(B0SN, replace_matched begin (B1B2(B0S0,B0S1), end; into method label BIFA code_regex \(B1SN, replace_matched begin (B1B2(B1S0,B1S1), end; into device label EC0 code_regex DT2B,\s+16 replace_matched begin T2B0,8,T2B1,8 end; into method label SMBR code_regex \(DT2B, replace_matched begin (B1B2(T2B0,T2B1), end; into method label SMBW code_regex Store\s+\(([^,]*),\s+DT2B\) replace_matched begin Store(%1,T2B0) Store(ShiftRight(%1,8),T2B1) end; into device label EC0 insert begin Method (RDBA, 0, Serialized)\n {\n Name (TEMP, Buffer(0x20) { })\n Store (BA00, Index(TEMP, 0x00))\n Store (BA01, Index(TEMP, 0x01))\n Store (BA02, Index(TEMP, 0x02))\n Store (BA03, Index(TEMP, 0x03))\n Store (BA04, Index(TEMP, 0x04))\n Store (BA05, Index(TEMP, 0x05))\n Store (BA06, Index(TEMP, 0x06))\n Store (BA07, Index(TEMP, 0x07))\n Store (BA08, Index(TEMP, 0x08))\n Store (BA09, Index(TEMP, 0x09))\n Store (BA0A, Index(TEMP, 0x0A))\n Store (BA0B, Index(TEMP, 0x0B))\n Store (BA0C, Index(TEMP, 0x0C))\n Store (BA0D, Index(TEMP, 0x0D))\n Store (BA0E, Index(TEMP, 0x0E))\n Store (BA0F, Index(TEMP, 0x0F))\n Store (BA10, Index(TEMP, 0x10))\n Store (BA11, Index(TEMP, 0x11))\n Store (BA12, Index(TEMP, 0x12))\n Store (BA13, Index(TEMP, 0x13))\n Store (BA14, Index(TEMP, 0x14))\n Store (BA15, Index(TEMP, 0x15))\n Store (BA16, Index(TEMP, 0x16))\n Store (BA17, Index(TEMP, 0x17))\n Store (BA18, Index(TEMP, 0x18))\n Store (BA19, Index(TEMP, 0x19))\n Store (BA1A, Index(TEMP, 0x1A))\n Store (BA1B, Index(TEMP, 0x1B))\n Store (BA1C, Index(TEMP, 0x1C))\n Store (BA1D, Index(TEMP, 0x1D))\n Store (BA1E, Index(TEMP, 0x1E))\n Store (BA1F, Index(TEMP, 0x1F))\n Return (TEMP)\n }\n end; into device label EC0 insert begin Method (WRBA, 1, Serialized)\n {\n Name (TEMP, Buffer(0x20) { })\n Store (Arg0, TEMP)\n Store (DerefOf(Index(TEMP, 0x00)), BA00)\n Store (DerefOf(Index(TEMP, 0x01)), BA01)\n Store (DerefOf(Index(TEMP, 0x02)), BA02)\n Store (DerefOf(Index(TEMP, 0x03)), BA03)\n Store (DerefOf(Index(TEMP, 0x04)), BA04)\n Store (DerefOf(Index(TEMP, 0x05)), BA05)\n Store (DerefOf(Index(TEMP, 0x06)), BA06)\n Store (DerefOf(Index(TEMP, 0x07)), BA07)\n Store (DerefOf(Index(TEMP, 0x08)), BA08)\n Store (DerefOf(Index(TEMP, 0x09)), BA09)\n Store (DerefOf(Index(TEMP, 0x0A)), BA0A)\n Store (DerefOf(Index(TEMP, 0x0B)), BA0B)\n Store (DerefOf(Index(TEMP, 0x0C)), BA0C)\n Store (DerefOf(Index(TEMP, 0x0D)), BA0D)\n Store (DerefOf(Index(TEMP, 0x0E)), BA0E)\n Store (DerefOf(Index(TEMP, 0x0F)), BA0F)\n Store (DerefOf(Index(TEMP, 0x10)), BA10)\n Store (DerefOf(Index(TEMP, 0x11)), BA11)\n Store (DerefOf(Index(TEMP, 0x12)), BA12)\n Store (DerefOf(Index(TEMP, 0x13)), BA13)\n Store (DerefOf(Index(TEMP, 0x14)), BA14)\n Store (DerefOf(Index(TEMP, 0x15)), BA15)\n Store (DerefOf(Index(TEMP, 0x16)), BA16)\n Store (DerefOf(Index(TEMP, 0x17)), BA17)\n Store (DerefOf(Index(TEMP, 0x18)), BA18)\n Store (DerefOf(Index(TEMP, 0x19)), BA19)\n Store (DerefOf(Index(TEMP, 0x1A)), BA1A)\n Store (DerefOf(Index(TEMP, 0x1B)), BA1B)\n Store (DerefOf(Index(TEMP, 0x1C)), BA1C)\n Store (DerefOf(Index(TEMP, 0x1D)), BA1D)\n Store (DerefOf(Index(TEMP, 0x1E)), BA1E)\n Store (DerefOf(Index(TEMP, 0x1F)), BA1F)\n }\n end; into device label EC0 code_regex BDAT,\s+256 replace_matched begin //BDAT, 256,\n BA00,8,BA01,8,BA02,8,BA03,8,\n BA04,8,BA05,8,BA06,8,BA07,8,\n BA08,8,BA09,8,BA0A,8,BA0B,8,\n BA0C,8,BA0D,8,BA0E,8,BA0F,8,\n BA10,8,BA11,8,BA12,8,BA13,8,\n BA14,8,BA15,8,BA16,8,BA17,8,\n BA18,8,BA19,8,BA1A,8,BA1B,8,\n BA1C,8,BA1D,8,BA1E,8,BA1F,8\n end; into method label SMBR code_regex \(BDAT, replaceall_matched begin (RDBA(), end; into method label SMBR code_regex Store\s\((.*),\sBDAT\) replaceall_matched begin WRBA(%1) end; into method label SMBW code_regex Store\s\((.*),\sBDAT\) replaceall_matched begin WRBA(%1) end; into method label ECSB code_regex Store\s\((.*),\sBDAT\) replaceall_matched begin WRBA(%1) end; into method label ECSB code_regex \(BDAT, replaceall_matched begin (RDBA(), end; into device label EC0 insert begin Method (RDBB, 0, Serialized)\n {\n Name (TEMP, Buffer(0x20) { })\n Store (BB00, Index(TEMP, 0x00))\n Store (BB01, Index(TEMP, 0x01))\n Store (BB02, Index(TEMP, 0x02))\n Store (BB03, Index(TEMP, 0x03))\n Store (BB04, Index(TEMP, 0x04))\n Store (BB05, Index(TEMP, 0x05))\n Store (BB06, Index(TEMP, 0x06))\n Store (BB07, Index(TEMP, 0x07))\n Store (BB08, Index(TEMP, 0x08))\n Store (BB09, Index(TEMP, 0x09))\n Store (BB0A, Index(TEMP, 0x0A))\n Store (BB0B, Index(TEMP, 0x0B))\n Store (BB0C, Index(TEMP, 0x0C))\n Store (BB0D, Index(TEMP, 0x0D))\n Store (BB0E, Index(TEMP, 0x0E))\n Store (BB0F, Index(TEMP, 0x0F))\n Store (BB10, Index(TEMP, 0x10))\n Store (BB11, Index(TEMP, 0x11))\n Store (BB12, Index(TEMP, 0x12))\n Store (BB13, Index(TEMP, 0x13))\n Store (BB14, Index(TEMP, 0x14))\n Store (BB15, Index(TEMP, 0x15))\n Store (BB16, Index(TEMP, 0x16))\n Store (BB17, Index(TEMP, 0x17))\n Store (BB18, Index(TEMP, 0x18))\n Store (BB19, Index(TEMP, 0x19))\n Store (BB1A, Index(TEMP, 0x1A))\n Store (BB1B, Index(TEMP, 0x1B))\n Store (BB1C, Index(TEMP, 0x1C))\n Store (BB1D, Index(TEMP, 0x1D))\n Store (BB1E, Index(TEMP, 0x1E))\n Store (BB1F, Index(TEMP, 0x1F))\n Return (TEMP)\n }\n end; into device label EC0 insert begin Method (WRBB, 1, Serialized)\n {\n Name (TEMP, Buffer(0x20) { })\n Store (Arg0, TEMP)\n Store (DerefOf(Index(TEMP, 0x00)), BB00)\n Store (DerefOf(Index(TEMP, 0x01)), BB01)\n Store (DerefOf(Index(TEMP, 0x02)), BB02)\n Store (DerefOf(Index(TEMP, 0x03)), BB03)\n Store (DerefOf(Index(TEMP, 0x04)), BB04)\n Store (DerefOf(Index(TEMP, 0x05)), BB05)\n Store (DerefOf(Index(TEMP, 0x06)), BB06)\n Store (DerefOf(Index(TEMP, 0x07)), BB07)\n Store (DerefOf(Index(TEMP, 0x08)), BB08)\n Store (DerefOf(Index(TEMP, 0x09)), BB09)\n Store (DerefOf(Index(TEMP, 0x0A)), BB0A)\n Store (DerefOf(Index(TEMP, 0x0B)), BB0B)\n Store (DerefOf(Index(TEMP, 0x0C)), BB0C)\n Store (DerefOf(Index(TEMP, 0x0D)), BB0D)\n Store (DerefOf(Index(TEMP, 0x0E)), BB0E)\n Store (DerefOf(Index(TEMP, 0x0F)), BB0F)\n Store (DerefOf(Index(TEMP, 0x10)), BB10)\n Store (DerefOf(Index(TEMP, 0x11)), BB11)\n Store (DerefOf(Index(TEMP, 0x12)), BB12)\n Store (DerefOf(Index(TEMP, 0x13)), BB13)\n Store (DerefOf(Index(TEMP, 0x14)), BB14)\n Store (DerefOf(Index(TEMP, 0x15)), BB15)\n Store (DerefOf(Index(TEMP, 0x16)), BB16)\n Store (DerefOf(Index(TEMP, 0x17)), BB17)\n Store (DerefOf(Index(TEMP, 0x18)), BB18)\n Store (DerefOf(Index(TEMP, 0x19)), BB19)\n Store (DerefOf(Index(TEMP, 0x1A)), BB1A)\n Store (DerefOf(Index(TEMP, 0x1B)), BB1B)\n Store (DerefOf(Index(TEMP, 0x1C)), BB1C)\n Store (DerefOf(Index(TEMP, 0x1D)), BB1D)\n Store (DerefOf(Index(TEMP, 0x1E)), BB1E)\n Store (DerefOf(Index(TEMP, 0x1F)), BB1F)\n }\n end; into device label EC0 code_regex BDA2,\s+256 replace_matched begin //BDA2, 256,\n BB00,8,BB01,8,BB02,8,BB03,8,\n BB04,8,BB05,8,BB06,8,BB07,8,\n BB08,8,BB09,8,BB0A,8,BB0B,8,\n BB0C,8,BB0D,8,BB0E,8,BB0F,8,\n BB10,8,BB11,8,BB12,8,BB13,8,\n BB14,8,BB15,8,BB16,8,BB17,8,\n BB18,8,BB19,8,BB1A,8,BB1B,8,\n BB1C,8,BB1D,8,BB1E,8,BB1F,8\n end; into method label SMBR code_regex \(BDA2, replaceall_matched begin (RDBB(), end; into method label SMBR code_regex Store\s\((.*),\sBDA2\) replaceall_matched begin WRBB(%1) end; into method label SMBW code_regex Store\s\((.*),\sBDA2\) replaceall_matched begin WRBB(%1) end; into method label ECSB code_regex Store\s\((.*),\sBDA2\) replaceall_matched begin WRBB(%1) end; into method label ECSB code_regex \(BDA2, replaceall_matched begin (RDBB(), end; # additional work for _BIX method present in some ASUS laptops into device label EC0 code_regex B0C3,\s+16 replace_matched begin XC30,8,XC31,8 end; into device label EC0 code_regex B1C3,\s+16 replace_matched begin YC30,8,YC31,8 end; into_all method label _BIX code_regex \(\^\^LPCB\.EC0\.B0C3, replaceall_matched begin (B1B2(^^LPCB.EC0.XC30,^^LPCB.EC0.XC31), end; into_all method label _BIX code_regex \(\^\^LPCB\.EC0\.B1C3, replaceall_matched begin (B1B2(^^LPCB.EC0.YC30,^^LPCB.EC0.YC31), end; into_all method label _BIX code_regex \(B0C3, replaceall_matched begin (B1B2(XC30,XC31), end; # or could remove the _BIX method if it turns out not to work #into_all method label _BIX remove_entry; #fix logic error in some newer ASUS DSDTs (issue #23) into method label FBST code_regex If\s\(CHGS\s\(Zero\)\)[\s]+\{[\s]+Store\s\(0x02,\sLocal0\)[\s]+\}[\s]+Else[\s]+\{[\s]+Store\s\(One,\sLocal0\)[\s]+\} replaceall_matched begin If (CHGS (Zero))\n {\n Store (0x02, Local0)\n }\n Else\n {\n Store (Zero, Local0)\n } end;  
      USB 3.0 & Instant wake fix
      #Maintained by: RehabMan for: Laptop Patches #usb_prw_0x0d_xhc.txt # remove _PRW methods to prevent instant wake # delete any existing XHC1 device into device label XHC1 name_adr 0x00140000 remove_entry; # delete any existing USB2 device into device label USB2 name_adr 0x001D0000 remove_entry; # if _PRW objects are methods into method label _PRW parent_adr 0x001D0000 remove_entry; into method label _PRW parent_adr 0x001A0000 remove_entry; into method label _PRW parent_adr 0x00140000 remove_entry; into method label _PRW parent_adr 0x001B0000 remove_entry; # some other LAN cards use 0x00190000 into method label _PRW parent_adr 0x00190000 remove_entry; # if _PRW methods are stuffed into a separate scope into method label _PRW parent_label _SB.PCI0.EHC1 remove_entry; into method label _PRW parent_label _SB.PCI0.EHC2 remove_entry; into method label _PRW parent_label _SB.PCI0.XHC remove_entry; into method label _PRW parent_label \_SB.PCI0.EHC1 remove_entry; into method label _PRW parent_label \_SB.PCI0.EHC2 remove_entry; into method label _PRW parent_label \_SB.PCI0.XHC remove_entry; # if _PRW objects are names into device name_adr 0x001D0000 code_regex Name.*_PRW.*\n.*\n.*\n.*\n.*\}\) remove_matched; into device name_adr 0x001A0000 code_regex Name.*_PRW.*\n.*\n.*\n.*\n.*\}\) remove_matched; into device name_adr 0x00140000 code_regex Name.*_PRW.*\n.*\n.*\n.*\n.*\}\) remove_matched; into device name_adr 0x001B0000 code_regex Name.*_PRW.*\n.*\n.*\n.*\n.*\}\) remove_matched; into device name_adr 0x00190000 code_regex Name.*_PRW.*\n.*\n.*\n.*\n.*\}\) remove_matched; # some _PRW have three entries in the Package into device name_adr 0x001D0000 code_regex Name.*_PRW.*\n.*\n.*\n.*\n.*\n.*\}\) remove_matched; into device name_adr 0x001A0000 code_regex Name.*_PRW.*\n.*\n.*\n.*\n.*\n.*\}\) remove_matched; into device name_adr 0x00140000 code_regex Name.*_PRW.*\n.*\n.*\n.*\n.*\n.*\}\) remove_matched; into device name_adr 0x001B0000 code_regex Name.*_PRW.*\n.*\n.*\n.*\n.*\n.*\}\) remove_matched; into device name_adr 0x00190000 code_regex Name.*_PRW.*\n.*\n.*\n.*\n.*\n.*\}\) remove_matched; # seems to work better if _PRW is present, but returns 0 (original was 3) for sleep state into device name_adr 0x001D0000 insert begin Name(_PRW, Package() { 0x0D, 0 }) end; into device name_adr 0x001A0000 insert begin Name(_PRW, Package() { 0x0D, 0 }) end; into device name_adr 0x00140000 insert begin Name(_PRW, Package() { 0x0D, 0 }) end; into device name_adr 0x001B0000 insert begin Name(_PRW, Package() { 0x0D, 0 }) end; into device name_adr 0x00190000 insert begin Name(_PRW, Package() { 0x0D, 0 }) end; # USB property injection for 7-series boards (originally HM76) # Insert Apple USB properties into EHC1 into method label _DSM parent_adr 0x001D0000 remove_entry; into device name_adr 0x001D0000 insert begin Method (_DSM, 4, NotSerialized)\n {\n If (LEqual (Arg2, Zero)) { Return (Buffer() { 0x03 } ) }\n Return (Package()\n {\n "subsystem-id", Buffer() { 0x70, 0x72, 0x00, 0x00 },\n "subsystem-vendor-id", Buffer() { 0x86, 0x80, 0x00, 0x00 },\n "AAPL,current-available", 2100,\n "AAPL,current-extra", 2200,\n "AAPL,current-extra-in-sleep", 1600,\n "AAPL,device-internal", 0x02,\n "AAPL,max-port-current-in-sleep", 2100,\n })\n }\n end; # Insert Apple USB properties into EHC2 into method label _DSM parent_adr 0x001A0000 remove_entry; into device name_adr 0x001A0000 insert begin Method (_DSM, 4, NotSerialized)\n {\n If (LEqual (Arg2, Zero)) { Return (Buffer() { 0x03 } ) }\n Return (Package()\n {\n "subsystem-id", Buffer() { 0x70, 0x72, 0x00, 0x00 },\n "subsystem-vendor-id", Buffer() { 0x86, 0x80, 0x00, 0x00 },\n "AAPL,current-available", 2100,\n "AAPL,current-extra", 2200,\n "AAPL,current-extra-in-sleep", 1600,\n "AAPL,device-internal", 0x02,\n "AAPL,max-port-current-in-sleep", 2100,\n })\n }\n end; # Insert Apple USB properties into USB 3.0 XHC into method label _DSM parent_adr 0x00140000 remove_entry; into device name_adr 0x00140000 insert begin Method (_DSM, 4, NotSerialized)\n {\n If (LEqual (Arg2, Zero)) { Return (Buffer() { 0x03 } ) }\n Return (Package()\n {\n "subsystem-id", Buffer() { 0x70, 0x72, 0x00, 0x00 },\n "subsystem-vendor-id", Buffer() { 0x86, 0x80, 0x00, 0x00 },\n "AAPL,current-available", 2100,\n "AAPL,current-extra", 2200,\n "AAPL,current-extra-in-sleep", 1600,\n "AAPL,device-internal", 0x02,\n "AAPL,max-port-current-in-sleep", 2100,\n })\n }\n end; # special cases... (not in u430 DSDT) #into scope label _SB.PCI0.XHC.RHUB.HS05 set_label begin _SB.PCI0.XHC1.RHUB.HS05 end; - Finally, click in "Compile" to check for errors.
      - If you get the error Object does not exists (\_SB.PCI0.XHC1) remove the 1 and try compile again.
      - Close and reboot.
       
      Last thing
       
      Run this command in Terminal to disable hibernation (doesn't work in macOS):
      sudo pmset -a hibernatemode 0  
       
      It's done!
       
       
      System Updates
       
      10.15.2
       
      Before install, update the following kexts:
      - Lilu.kext. I used version 1.4.0.
      - WhateverGreen.kext. I used version 1.3.5.
      - AppleALC.kext. I used version 1.4.4.
      - VoodooPS2Controller.kext. I used version 2.1.0.
      (all download links above)
       
      Download the latest CLOVERX64.efi.zip build. I used version 5100.
      Mount EFI partition and unzip to:
      - /Volumes/EFI/EFI/CLOVER/CLOVERX64.efi
      - /Volumes/EFI/EFI/BOOT/BOOTX64.efi (rename the copy of CLOVERX64.efi to BOOTX64.efi
       
      Install update. Will reboot at least four time.
       
       
      10.15.4

       
      Before install, update the following kexts:
      - Lilu.kext. I used version 1.4.2.
      - WhateverGreen.kext. I used version 1.3.7.
      - AppleALC.kext. I used version 1.4.7.
      - VoodooP2Controller.kext. I used versions 2.1.2.
      - VirtualSMC.kext. I used version 1.3.7.
      - Legacy Video Patch (If Core i3 machine)
      (all download links above)
       
      Download the latest CLOVER installer. I used version 5107.
      - Install respecting the configuration mentioned above in "Install bootloader" section.
       
      Install update. Will reboot at least four time.
       
       
       

      And last but not least

      I would like to thank the following community members, by making these dream possible:
      @crushers, @snatch, @apianti, @blackosx, @blusseau, @dmazar, @slice2009, @autumnrain, @phpdev32, @EMlyDinEsH, @RehabMan, @Scellow, @mitch_de, @Shailua, @Andy Vandijck, @maxfierke, @ArturXXX, @LexHimself, @brumas, @"Sniki", @Mieze, @headkaze and all others members involved directly or indirectly.
       
       
      Attachments
       
      config.plist
      SSDTs v3.zip
      USBPorts.kext.zip
      VoodooPS2Controller.kext.zip
      Filevault 2 additional drivers.zip
      AtherosE2200Ethernet.kext v2.zip
       
    • By tluck
      Lenovo T460 macOS with Clover Guide
      Latest Release on GitHub (March 2020) Updated to Clover r5105 Updated Lilu based kexts - Lilu, ALC, WEG Added AirportBrcmFixup.kext
        Various Tweaks over Last months The zip file is a complete Clover ESP (/EFI) bundle and kext pack for the Lenovo T460. The current file bundle is tested on Sierra. 
      Note: I never got the GFX fully working on El Capitan. 
      Full Clover file set - config.plist etc. Includes all custom kexts Includes custom DSDT/SSDT scripts and patches Utility scripts The zip bundles are posted to GitHub: https://github.com/tluck/Lenovo-T460-Clover/releases
      Caveat: The T460 systems used here was configured with: i5-6300U, Intel HD Graphics 520, 1920x1080 touch screen. If you have a different system model, then extract the ACPI files and use the included scripts to create a set of files consistent with your system type and BIOS version. See below for details.
      Credits: RehabMan, Shmilee, vusun123, TimeWalker, Mieze from which, much of their work and help is/was was used to get the T460 to this point.
      Devices and aspects working:
      Ethernet -  Intel I219LM is enabled via IntelMausiEthernext.kext WiFi/BT - substitute the Intel WiFi/BT with a compatible Broadcom or Atheros chip Audio - ALC293 codec implemented via AppleALC.kext (the old AppleHDA_ALC293 and CodecCommander kexts are not needed) PS2 - ClickPad + TrackPoint + all 3 buttons - using a modified VoodooPS2Controller to support new layouts - and added some custom Fn key maps based on 440/450 dsdt USB - implemented via custom SSDT + USBInjectAll kext. All USB3/USB2 ports are intel-based and work -  3 external USB and internal Camera, BT, etc  Sleep/Wake - the sleepwatcher package and custom sleep/wake scripts are used to help with sleep/wake for BT and PS2 devices. Note: have not tried to implement the SD card reader - no driver found.
      ACPI Files
      New Installation - Steps and Details
      Part 1 - OS Installation
      Part 2- Post OS Installation and Setup
      Notes on Custom Kexts
       
    • By Ramirez71
      Buongiorno a tutti sono Paolo e volevo ringraziare tutta la comunità per le risorse che mette a disposizione e grazie alle quali ho da poco realizzato un Hackintosh Mojave con metodo "Vanilla" quasi del tutto funzionante.
      Come da titolo il problema- l'unico per adesso- da me rilevato consiste in una grafica del macOS e delle app molto sgranata. Se apro un video su YouTube il problema non esiste mentre sul resto dell'interfaccia (comprese immagini aperte su anteprima o Foto) persiste.
      Andiamo per gradi con la presentazione: mobo Asus P8B75plus, I53470S (grafica integrata Hd2500), 8GB ram (2X4gb), SSD 256 GB, Sapphire nitro RX480, per schermo sto usando una TV full hd  collegata con cavo Hdmi (sulla quale duplico anche un iMac Mid2011 con successo e senza alcun problema di grafica).
      Istallazione con Clover impostato come da guida su Gitbook (che poi mi pare simile a quella di Gengik se non erro) usando i kext soliti in "other" (lilu, whatewer, applealc, virtualscm anzichè fakescm con flaggate tutte le opzioni, RLT8111, usbinkjet etc) config.plist quella per Ivybridge scaricata dal RAW di Gitbook e modificata in post istallazione solo nei tempi di start del boot. Bios dettato come da guida nei limiti delle opzioni offerte da questa mobo: grafica principale su PCLe ma non c'è un comando diretto per disabilitare quella integrata. Provato anche altre modifiche nel settario della partizione eri cercando soluzioni in rete che nel migliore dei casi non hanno portato risultati (nel peggiore non ripartiva).
      Sono un po incavolato perché se non fosse per questo tutto sarebbe andato a meraviglia al primo colpo!!!!!!
×