High Sierra or Mojave on HP 800 G1 USDT,SFF and tower PC's, 10.14

[Donw35 56]

 

10.14 using Intel onboard iGPU

 

1. Install Sierra from a real MAC to the hard drive going into the HP EliteDesk 800 G1

2. Install Clover v4813 from real MAC to hard disk with the below options checked

   * Clover for UEFI booting only

   * Install Clover in the ESP

   * Themes

   * drivers64UEFI

              ApfsDrvierLoader-64..efi

              AptioMemoryFix-64.efi

   * Install RC scripts on target volume

   * Optional RC Scripts - All

   * Install Clover Preference Pane

3 Use Clover Configurator to Edit config.plist but see below for the code or just use mine and rename to config.plist 

4 Added the following Kext's to \EFI\CLOVER\kexts\Other

   *** Versions are important, use these or higher ***

   FakeSMC_ACPISensors.kext version 6.25-333-g05e0f4be.1759

   FakeSMC_CPUSensors.kext version 6.25-333-g05e0f4be.1759

   FakeSMC_GPUSensors.kext version 6.25-333-g05e0f4be.1759

   FakeSMC_LPCSensors.kext version 6.25-333-g05e0f4be.1759

   FakeSMC.kext 6.26-357-gceb835ea.1800

   IntelMausiEthernet.kext 2.4.0d0

   USBInjectAll.kext 0.6.7

   VoodooHDA.kext 2.9.1

   Lulu.kext 1.2.8

   WhateverGreen.kext 1.24

5 Reboot and setup

6 Sleep working, wake up using keyboard  -- open terminal and type sudo pmset -a standby 0   to resolve issues with waking up

 

I only tested video using the DP port

4k does not work

 

 

10.13.6 

Note: this will probably work for other EliteDesk Towers, Small Form Factor and Ultra Small Form Factor

 

Working -- here is what I did with some help from others

 

1. Installed Sierra from a real MAC to the hard drive going into the HP EliteDesk 800 G1

2. Installed Clover v4630 from real MAC to hard disk

       Bootloader - Install boot0af in MBR

       CloverEFI - CloverEFI 64-bits SATA

       Drivers64UEFI

              ApfsDrvierLoader-64..efi

              AptioMemoryFix-64.efi

       Install all RC scripts on target volume

       Install Clover Preference Pane

3 Used Clover Configurator to Edit config.plist but see below for the code

4 Added the following Kext's to \EFI\CLOVER\kexts\Other

      F akeSMC.kext

      IntelMausiEthernet.kext

      Lili.kext

5 Sound working with VoodooHDA 2.8.9 Clover-V6 (sound comes out of the internal speaker and green jack)

6 WiFi working OOB (AR9280 AR5BHB92 PCIe) Amazon $17

7 Sleep working, wake up using keyboard  -- open terminal and type sudo pmset -a standby 0   to resolve issues with waking up

 

 

UPDATE 11/17/2018 *** Speed step was not working FIXED *** EFI zip is a copy of the settings I am using. create your own serial number.

As of this date, my Mojave 10.14.1 is solid, I did do a test and 4k @ 60hz is not working. Not a problem at this moment and once we have Nvidia drives I have a 1050ti for this machine that I will go back to, then I will get my 4k monitor for. this machine.

 

Clover 4813

 

Below version or higher required to boot

 

EFI/CLOVER/kexts/Other

FakeSMC_ACPISensors.kext version 6.25-333-g05e0f4be.1759

FakeSMC_CPUSensors.kext version 6.25-333-g05e0f4be.1759

FakeSMC_GPUSensors.kext version 6.25-333-g05e0f4be.1759

FakeSMC_LPCSensors.kext version 6.25-333-g05e0f4be.1759

FakeSMC.kext version 6.25-333-g05e0f4be.1800

IntelMausiEthernet.kext version 2.3.0b0

Lilu.kext version 1.2.8

USBinjectAll.kext version 0.6.8

WhatEverGreen.kext 1.2.4

VoodooHDA.kext version 2.9.1

 

EFI/CLOVER/drivers64UEFI

AppleDriverLOader-64.efi

AptioMemoryFix-64.efi

 

 

 

 

 

 

 

HP_800_G1_Elitedesk.zip

Edited January 6 by Donw35
added tag

[Allan 5,177]

Edit your config.plist and add these values:

 

config.plist/Devices/FakeID/IntelGFX=0x04128086

 

Or use FakePCIID.kext and FakePCIID_Intel_HD_Graphics.kext

 

Credits: RehabMan.

[Donw35 56]

tried both methods, Clover boots but when tries to boot of the drive I just get back screen and +++++++++++++++++++++++++++++++++++++++++++++++++++++ across the top

resolved, see above

[MaLd0n 5,877]

Use KernelPm in config.plist

[Donw35 56]

Working, I will add it to the list, Thanks of the help

[wishie 3]

I followed this guide today, but found that the machine still wouldn't boot.. i had to manually select "KernelPM" patch when booting, even though it was in the config.plist (as copy/pasted from this thread).

What I ended up doing was formatting the config.plist, and now it all works.. odd, I know, but hey, the machine is now working.

Also, it should be mentioned that VGA output isn't supported at all by macOS so you must use the DisplayPort outputs to get to the desktop. Some users might not realise this.

All in all, now that its working, its working really well.. this is a neat little replacement for a MacMini. I have a 256Gb Samsung SSD in mine, and its nice and zippy.

[Donw35 56]

the plist I posted lost its formatting when I pasted it into the thread but it should be easy for user to figure out what I did

[Donw35 56]

Currently the same process for High Sierra, I am using newer versions of the following 

 

CLOVER 4233

USBInjectAll.kext 0.6.2

Lilu.kext 1.1.7

FakeSMC.kext 6.25-333

 

although I do not know if that is required.

[erak 0]

Thanks for this, works great!

 

I didn't add USBInjectAll as I haven't noticed any USB issues. And Lilu is unnecessary without a plugin afaik.

 

 

BUT, HD4600 is affected by the PAVP freeze, which I noticed when surfing with Safari. Complete system freeze when playing certain videos. Lilu + IntelGraphicsFixup fixes the issue.

 

Lilu - kext and process patcherLilu - kext and process patcher

[fruity_looper 0]

Is installing from a real Mac to the hard drive going into the HP EliteDesk 800 G1 the only way to make this work?

 

EDIT: I'm currently using a HP EliteDesk 800 G1 SFF with a i5 4590 with 8GB Ram and here's what I'm getting even with trying to install it from a real mac to the hard drive going into the PC

 

I've followed all the steps, added the parts that were highlighted in red in the config.plist using Clover Configurator 2 

 

I've added the kexts to \EFI\CLOVER\kexts\Other:

FakeSMC.kext

nullCPUPowerManagement.kext

IntelMausiEthernet.kext

USBInjectAll.kext

Lilu.kext

FakePCIID.kext

FakePCIID_Intel_HD_Graphics.kext

 

 

EDiT 2: The cause for the panic seemed to have been all the fixes were selected in my config.plist when I had a look on clover configurator so I unchecked all of them except for the ones you had in your config.plist and bingo! Working! 

 

Thank you!

[cgreg 1]

Thanks for the write-up! I got it installed on my HP ElitrDesk 800 G1 USDT and booted properly on the first try although it took a while to get everything right in clover and cover configurator.

 

The only issue was not knowing that I was supposed to do everything with the config.plist from my real MacBook Pro when setting up. After I realized that it was much easier. I had never used clover configurator so I had to learn where everything was like the text option at the bottom where I was able to copy pasta your plist.

 

Now if I could get the audio to come through the HDMI I'll be all set! But the speaker from the machine will work fine.

[Donw35 56]

@erak -I haven't experienced any issues with the video using this method.

 

@cgreg - your welcome. glad you got it working

 

if anyone comes up with better working results please post..

[erak 0]

@erak - I haven't experienced any issues with the video using this method.

 

Visit for example https://www.clover.com/(which I did by mistake) with Safari. It completely froze my system. Afaik, this should affect all HD 4600. But if you browse with chrome, you're unaffected.

[pagolo 1]

Hello,

I'm French and new on this topic.

So excuse me if I don't write english as well as a native english guy!

I hope that I can get help from you.

I'm new on hackintosh : I already try wth partial success on shuttle barebone.

And now I would like to try on this elitedesk 800 G1 usdt (i5-4570S)

I try to do as the first post (with high sierra instead).

I downloaded clover configurator but I do not know how it's work. So I tried to copy/paste the proposal on first page.

 

When I start the hackintosh (I have clover page) I start on the SSD where MacOS is and after many lines I have a message about a problem with the CPU.

 

May I ask you  a download of your config.plist or a help to use cloverconfigurator?

 

Many thanks

 

[Donw35 56]

if you are going to upgrade from 10.13.1 to 10.13.2 follow these steps for a efforts free upgrade

 

first upgrade clover to r4334

then download the follow kext and put the in your kexts EFI folder

Lilu.txt version 1.2.1

NvidiaGraphicsFixup.kext 1.2.1 <- if you have an Nvidia graphics card

 

The reboot

now you can upgrade from the App Store to 10.13.2 - failing to do so will cause your 800 G1 to not boot

Hello,

 

 

May I ask you  a download of your config.plist or a help to use cloverconfigurator?

 

Many thanks

I added the config.txt, this is the one I user for the USDT 

[wishie 3]

So im having issues with my HP EliteDesk 800 G1 USDT machine. I can make it crash by viewing certain websites in Safari.. it causes a hard lockup.

 

 

Hi all,

So I have built quite a few hackintoshes over the last decade, and have usually ended up with rock solid machines. Currently, I have 2 hackintoshes, my main one being a liquid cooled i7-4770, 32Gb RAM, 240Gb m.2 SSD, GTX 980, and a bunch of other SATA SSD's for photoshop caches, after effects etc.. this machine has been rock solid, and never skips a beat. Currently on macOS 10.13.2..

However, my other hackintosh is where I am having some issues. It's a HP EliteDesk 800 G1 - i5-4570T, 16Gb RAM, 256Gb EVO 850 SSD, with onboard Intel 4600 graphics. Now, for every day tasks, this machine has been very stable, and even handles my 'at home' photoshop/after effects/final cut pro x workload. The issue I have been facing though, is that certain websites seem to make the machine hard lock. This ONLY happens in Safari, and it seems to be triggered by some sites that have video players on them. Oddly, YouTube/Facebook etc do NOT cause the issue.

An example URL that causes the hardware lockup is https://shareably.net/cat-takes-back-treats-ducks/ . If I view that URL in Safari on the HP EliteDesk, the machine hard locks within about 5 seconds. The same URL works perfectly fine on Chrome though. Also, its not just this one URL, but quite a few sites, and they all seem to use some sort of video player.

Now, the HP EliteDesk 800 G1 is currently running macOS High Sierra 10.13.2. The only (non-standard) kexts I have loaded, are FakeSMC, IntelMausiEthernet and VoodooHDA.

Please let me know what other information you might need to help me figure out why Safari crashes the machine.

 

 

[wishie 3]

I really should have checked this thread more thoroughly before posting.. I found the comment about PAVP issue, installed Lilu and IntelGraphicsFixup and no more freezes!

 

Now im wondering if its possible to use some other audio kext, instead of VoodooHDA? Perhaps AppleALC plugin for Lilu? Anyone tried?

[Donw35 56]

I haven't tried that, for my HP 800 G1 I am using a USB (works OOB) for sound, VoodooHDA has some issues for basic sounds its ok, for movies and music I prefer the USB sound device.

[pagolo 1]

it's alive ! 

thank you so much.

It's work

I need to find the little screw for the wifi card and it will be perfect!

[Donw35 56]

Those little screws are hard to find, I found one in a laptop for the wifi card, it had two so I took on from that.. 

[wishie 3]

Anyone tried using two monitors with the 800 G1?

 

I currently have 1 x HP EliteDisplay E232 and I'm thinking of getting another one soon.. if it will work

[Donw35 56]

I can confirm that two monitors work using the display ports (2), I tried using one Display port and the VGA but that did not work. 

[wishie 3]

yeah, the VGA port doesn't work at all, because no Mac's capable of running High Sierra have a VGA output, as far as I know.

 

I'll be using both DisplayPort anyway, as I have just acquired another EliteDisplay E232

 

Thanks for confirming.

[Donw35 56]

Good deal, these little HP's are turning into Mac mini killers... lol

[Donw35 56]

Did the latest update for 10.3.2 and all went well, no issues.