Jump to content
MaLd0n

[Guide] Sierra / High Sierra on Gigabyte GA-H97M-D3H / DSDT

149 posts in this topic

Recommended Posts

Advertisement

if you mean CPU graphics card ? no i don't disable it

during the installation the HD 4600 of my i7 4770 S is activated

I must disable it ?

Edited by moonbase70

Share this post


Link to post
Share on other sites

Sorry, but what are the settings to pre configure BIOS on this MOBO ?

Sorry, but what are the settings to pre configure BIOS on this MOBO ?

Share this post


Link to post
Share on other sites
21 hours ago, klausbartu said:

Sorry, but what are the settings to pre configure BIOS on this MOBO ?

Sorry, but what are the settings to pre configure BIOS on this MOBO ?

default

Share this post


Link to post
Share on other sites

Hi MaLd0n ,
I have a problem with my hackintosh :

Today i have try to upgrade my system from Sierra 10.12.6 to High Sierra but i could not make the update from the Hackintosh because is stuck on apple logo , so i try to start in verbose mode but without success ... (in attached some picture of the logs).

After that i disconnect the SSD from the hackintosh and i tried the update from my macbook pro and the update goes fine , after that i reconnect the SSD to the hackintosh but still don't start and the error in verbose mode is the same.

The SM bios is Mac pro 5.1 and i use the SSDT tha you make for me for Sierra (i have tried to remove the SSDT but without success the hack still not start)

This is the configuration of my sistem

MOBO   GA Z87X UD7 TH rev 2.0
CPU       i7 4790k
GPU       GTX 760 4gb
32 GB RAM

What can i do for solve the problem ?
Thank you in advance

 

 

65901952_10220543310599596_2774083741142745088_n.jpg

IMG-20190630-WA0013.jpg

IMG-20190630-WA0011.jpg

IMG-20190630-WA0009.jpg

IMG_20190630_155409.jpg

Share this post


Link to post
Share on other sites
27 minutes ago, moonbase70 said:

Hi MaLd0n ,
I have a problem with my hackintosh :

Today i have try to upgrade my system from Sierra 10.12.6 to High Sierra but i could not make the update from the Hackintosh because is stuck on apple logo , so i try to start in verbose mode but without success ... (in attached some picture of the logs).

After that i disconnect the SSD from the hackintosh and i tried the update from my macbook pro and the update goes fine , after that i reconnect the SSD to the hackintosh but still don't start and the error in verbose mode is the same.

The SM bios is Mac pro 5.1 and i use the SSDT tha you make for me for Sierra (i have tried to remove the SSDT but without success the hack still not start)

This is the configuration of my sistem

MOBO   GA Z87X UD7 TH rev 2.0
CPU       i7 4790k
GPU       GTX 760 4gb
32 GB RAM

What can i do for solve the problem ?
Thank you in advance

use a fresh install

https://olarila.com/forum/viewtopic.php?f=50&t=8685

Share this post


Link to post
Share on other sites

Hi MaLd0n ,

Finally Solved !!

dropping the ACPI MATS/DMAR tables

Now it start correctly , i can use the SAME SSDT you make for sierra or not ?

Let me know

Thank you !!

 

Share this post


Link to post
Share on other sites
Just now, moonbase70 said:

Hi MaLd0n ,

Finally Solved !!

dropping the ACPI MATS/DMAR tables

Now it start correctly , i can use the SAME SSDT you make for sierra or not ?

Let me know

Thank you !!

 

extract new

--Run_Me
RunMe.app

have some updates

Share this post


Link to post
Share on other sites
2 minutes ago, moonbase70 said:

How can i send you ?

here the max limit i 10 mb and my EFI folder is 27 mb compressed

google drive, zippyshare or other service

Share this post


Link to post
Share on other sites

I have two curiosities to ask you:

1- I noticed that you changed the SM BIOS configuration from Mac Pro 5.1 to iMac 14.1, can I ask you why you didn't choose iMac 15.1 (27 inch retina 5K) which has the same i7 4790K processor?

2 - on my machine are installed plugins that go to read the serial number of the motherboard can I put back the old serial so as not to have problems?

 

Let me know

Thank you in advance

Share this post


Link to post
Share on other sites
34 minutes ago, moonbase70 said:

I have two curiosities to ask you:

1- I noticed that you changed the SM BIOS configuration from Mac Pro 5.1 to iMac 14.1, can I ask you why you didn't choose iMac 15.1 (27 inch retina 5K) which has the same i7 4790K processor?

2 - on my machine are installed plugins that go to read the serial number of the motherboard can I put back the old serial so as not to have problems?

 

Let me know

Thank you in advance

the correct is iMac14 or 15, but u can use ur old;) 

Share this post


Link to post
Share on other sites
Just now, moonbase70 said:

you mean the old serial number right ?

ur old serial is for macpro5, use ful smbios macpro5

Share this post


Link to post
Share on other sites
Just now, MaLd0n said:

ur old serial is for macpro5, use ful smbios macpro5

ok i use the old sm bios so i cannot loose any plugins :-)

did you receive the new send me files ?

 

Share this post


Link to post
Share on other sites

 

32 minutes ago, moonbase70 said:

ok i use the old sm bios so i cannot loose any plugins :-)

did you receive the new send me files ?

 

ye, looks good;)

Share this post


Link to post
Share on other sites
13 minutes ago, moonbase70 said:

so i only change the SM BIOS parameter an it's done ?

yes

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By shinho73
      Hello everyone. I managed to install AMD Sierra V5(10.12.6) on my old AMD A8 7600 PC(Mother Board-A58M-E, GPU- Palit Geforce GT730 DDR3). Everything is working except the GPU. The GT730 DDR3 GF108 is natively supported on Sierra, but for some reason, it is not working. On Clover Config, "Inject Nvidia" is selected, no Nvidia Web, and nv_disable=1. On "About This Mac" it just says " NVIDIA Chip Model 3 MB".
      I have attached config.plist. Can someone look at it please? Any help will be greatly appreciated. Thank you. 





      config.plist
    • By fusion71au
      Clover r5050 ISO compiled with GCC and minimal config.plist compatible for use in VMWare Workstation.
       
      Tested with unlocked Workstation 15 running OSX 10.9 -->10.15 guest in Windows X64 host.
       
      Installation
      1. Download and unzip "EFI_Clover_r5050 for VMware.zip". Mount Clover-v2.5k-5050-X64.iso by double clicking on it.
      2. Mount your VM's EFI System Partition eg in terminal
      sudo diskutil mount disk0s1   3. Copy EFI folder from step 1 into the EFI partition
      4. Shutdown the VM, add bios.bootDelay = "3000" to your VM's vmx file
      5. Reboot your VM, press <F2> to access the VMware Boot Manager and add CLOVERX64.efi to the boot menu.
       
      Substitute your own unique and valid MLB and ROM variables in the /EFI/CLOVER/config.plist (Rt Variables section) to activate iMessage/Facetime on your VM.
    • By Slice
      I successfully installed macOS 10.11.6 and Windows 7 Pro SP1 in UEFI mode on the laptop.
      I know, there are detailed guides here and on osxlatitude.com but I was not agree with them and carefully check and test every step to tune my Mac.
       
      Hardware
      Intel® Core� i5-3320M CPU @ 2.60GHz, speedstep works with Clover default settings
      Chipset Intel 7 series, no patches needed
      Video: IntelHD4000 or NVS5200M switchable in BIOS, work in both cases
      LAN; Intel 82579LM, works with IntelMausiEthernet.kext v2.2.1
      Audio: IDT 92HD93BXX, works with VoodooHDA 2.9.0.
      SDHC reader O2Micro; works with native AppleSDHC.kext with Clover Arbitrary properties.
      USB3.0 works natively if not disabled in DSDT
      PS2 keyboard and touchpad works with VoodooPS2.
      WiFi: Dell Intel WiFi was replaced by Dell DW1520, Broadcom BCM943224HMS. DeviceID=4353
      LCD Screen 1366x768
      BIOS A12. Initially was A02. Then I flashed A23 and found it is quite bad. The screen is full of artefacts. Flash A12 and all is OK. Not tested other versions.
      For some reason BIOS can switched from Intel to Nvidia by itself so I have to do my solution working independent on this state.
       
      WiFi
      It is not working OOB although it has DeviceID known to Apple. The reason is WhiteList in the driver.
      I set MacModel as MacBookPro10,1 while the WiFi will work on MacBookAir. I make a patch in Clover.
      As well a patch for channels.
      I deleted a kext Brcm4331 because it has the same DeviceID. Let kext Brcm4360 to work alone.
       
      VideoCards
      In Bios we can set Optimus = Enable/Disable
      If Enable then we have two videocards Intel first and Nvidia second. In this case additional SSDT-3.aml will switch off Nvidia.
      If Disable then we have only Nvidia card. It will work if Board-ID taken from iMac13,2.
      But here there is contradiction with WiFi with required Board-ID from MacBookAir.
      So I take MacModel as MacBookPro10,1 which is most close by CPU IvyBridge.
      Set BoardID like iMac13,2 to make Nvidia working.
      Patch BoardID in Brcm4360 to make WiFi working.
      Now I have
      Inject->
      ->Intel=YES
      ->Nvidia=YES
      and SSDT-3.aml in ACPI\patched folder. This SSDT will switch off Nvidia if Intel card ON.
      For Intel graphics there is a patch against 8 apples at start.
      This Nvidia 5200 is Fermi and works in ElCapitan.
       
      Brightness
      No special kexts.
      The brightness controlled by keys F1,F2 and slider in Control Panel in both case Intel or Nvidia. Details here  #72 
       
      DSDT and SSDT
      This is very long story and finally I have working sleep in both cases Intel or Nvidia.
       
      Sensors
      I use my HWSensors3 with FakeSMC 3.5.2.
      I got monitoring:
      CPU temperature
      GPU temperature
      GPU main frequency
      GPU shader frequency
      Battery state % full, time to charged or time to empty.
      Battery voltage dinamically.
      Battery amperage dynamically. I can see it changes on heavy games.
      HDD temperature.

       
      Audio
      I like VoodooHDA and have no problems with it.
      The sound is clear, loud, and switchable between internal speaker and headphone.
      Mic is working.
       
      Bluetooth
      Just tested with BTFirmwareUpdate.kext and it works in 10.11.6. I not needed it so switched off by wireless switch at right side.
      For 10.13.6 there is other kext BRCMInjector.
       
      Keyboard, Touchpad and Touchstick
      Post #14
      I made my fork of the VoodooPS2 driver, take here sources and release version
      https://github.com/SergeySlice/VoodooPS2-for-ALPS
       
      My config, ACPI files and kexts are in attachment.
      05.12.2017
      EFI.7z
       
      EDITED:
      Better DSDT in the post #6.
      Sleep working even when AC inserted.
       
      EDITED 06.12.2018
      Now I have HighSierra and this is my EFI folder. Note, HighSierra is possible only with Intel graphics (Optimus is enabled in BIOS)
       

       
       
      Welcome to discussion!
      EFI-E6430.7z
      BRCMInjector.kext.zip
    • By shinho73
      I need a good vanilla guide for AMD A8 7600 with A58M-E FM2+ mother board and Palit GEforce GT 730. Any help will be greatly appreciated. Thank you.



    • By Pedro Diniz
      Hello Friends, how are ya?

      Could you help me with a problem?

      I followed some guides like: https://www.insanelymac.com/forum/topic ... coffeelake -dsdt /

      and the installation of high Sierra 10.13.6 (17G8030) and nvidia webdrivers (correspondent to OS version) went smoothly, the problem starts when I try to boot the GPU.

      Hardware:
      MOBO: Aorus B360M gaming 3 (rev.1)
      CPU: i5 8400
      GPU: GTX 1060 OC Galax redblack

      BIOS:
      Fast boot - disabled
      windows 8/10 features - other os
      lan pxe - disabled
      storage boot option - UEFI
      other pci devices - UEFI
       
      Initial display output - PCie 1 slot
      Intel's Platform Trust Technology (PTT) - disabled
      sata mode selection - AHCI
      XHCI hand off - enabled
      VT-d - disabled
      internal graphics - auto


      The problem is:
      I can log into the system normally without using my nvidia GPU but when I boot the system with the flags for webdrivers to work I fall into the login screen but it keeps flashing, I can see the mouse and I can move it but the screen flashes and the following error appears when the screen goes "black": IOConsoleUsers: gIOScreenLockState 3, hs 0, bs 0, now 0, sm 0x0. I searched for this error on the internet and tried to solve but to no avail so far.

      If someone can help me I would be extremely grateful! thanks in advance!

      Clover file attached.
      CLOVER.zip
×