Jump to content
MaLd0n

[Guide] Sierra / High Sierra / Mojave / Catalina on mobos Serie 100 / 200 / 300 / SkyLake / KabyLake / CoffeeLake DSDT

5,288 posts in this topic

Recommended Posts

Hey MaLd0n, Awesome guide, thank you so much, here are my clover files+ACPI+IORegistry.
My specs are the following:

 

Mobo: GA-Z270-HD3P Rev 1.0 Bios F7

CPU: i5 7500

GFX: Gigabyte GT 1030 OC 2GB
Ram: 1x16GB

Storage: Kingston SSD 120GB for system and i will throw in another 2TB HDD as soon as I'm done with the system setup

 

I installed El Captain 1st and then upgraded using the app store so that i can have the final update of Sierra with kabylake support, after installing Sierra, i removed fakeCPU ID, and changed my smbios to 18,2 as that specific model uses the same CPU that i have at the moment, so i don't really understand, do i need any PM hacks, or is my CPU OOB?

Here are the files you requested, can't wait to have this beast up and running, I've been on 10.8.5 on a C2Q Q6600 for the past couple of years.... lol (might upgrade it to El Captain using your other guide :)

Send to Maldon.zip

Share this post


Link to post
Share on other sites
Advertisement

Hi. I just built the pc in the signature.

I installed high sierra, so if you can't help me can you please show where are the patches you list in the first post?

It works, but i thinks it's not perfect and i'm not able to edit my dsdt properly as i did with my laptop.

Thanks!

CLOVER.zip

Paolo’s iMac.ioreg.zip

Send me Paolo’s iMac.zip

Share this post


Link to post
Share on other sites

Thanks for your guide. I, too would like to know about your patches. If you could post them I would try to patch my own myself. :)

 

 

Board: Z270N Gaming 5

Ram: 16gb

CPU: 7700k

GPU: MSI 1060 6gb OC

 

Attached is the disassembled (and assembled) DSDT and SSDTs along with my Clover sans the theme folder.

Thank you for taking the time to look at it.

GA-z270n gaming 5 -TrustAugustus.zip

TrustAugustus iMac IOREG.zip

Share this post


Link to post
Share on other sites

So I followed everything and have a working system!

I dont suite understand the DSDT, but I have done everything else.

 

MOBO: GA-Z270X-UD5

CPU: i7700k

GPU: 1080 Ti

 

OS: 10.12.6

 

Clover Folder:

https://www.dropbox.com/s/ynraiilcxezaqwg/CLOVER.zip?dl=0

 

"Send me file"

https://www.dropbox.com/s/9oku4sftx9hjduc/Send%20me%20superflex%E2%80%99s%20iMac.zip?dl=0

 

Ioregistry:

https://www.dropbox.com/s/n98vs3wc1w5om76/ioregistry.ioreg?dl=0

 

thank you so very much for making this possible!

 

 

Edit. The only issue im experiencing, is that 1 disk doesnt show up after reboot. When i shut down, and power on again, all disks are back.. How come?

Share this post


Link to post
Share on other sites

Hi it would be awesome if you could help me out as well.

 

On High Sierra

 

I got a i7 7700k @5100mhz on a

GA z270-UD5.   F5 BIOS

16gig 3000mhz

and a 

GTX1070

 

Getting some proper mA to the USB would be epic.

 

I hope I added all necessary files.

 

Mille Grazie

CLOVER.zip

Send me test’s iMac.zip

SSDT 7700k 5.1ghz.zip

IOREG test’s iMac.zip

Share this post


Link to post
Share on other sites

Hi sir Maldon

 

I built a hackintosh

my specs MB GA-B250M-D3H

Cpu Core i5 7500 intel HD 630

send me clover UEFI for installation macOS Sierra and 

post installation advise

 

Thanks in Advance.

Share this post


Link to post
Share on other sites

Hi Maldon,

 

you dont need to do the DSDT edits like this editing the actual file.  Clover has sections in it called drop dsdt tables and then patch each item from the clover config.plist file alone.  just an update for people who keep posting their dsdt's and you dont need to edit every dsdt file people post.

 

What program and patches are you using to do the patches?

Share this post


Link to post
Share on other sites

Hi Maldon,

 

you dont need to do the DSDT edits like this editing the actual file.  Clover has sections in it called drop dsdt tables and then patch each item from the clover config.plist file alone.  just an update for people who keep posting their dsdt's and you dont need to edit every dsdt file people post.

 

What program and patches are you using to do the patches?

lol

clover have a very basic patches, all hacks need a good edited DSDT ;)

check clover page and see slice talkin' about it

create patches with datasheet, ioreg and tables real macs and tests, many tests and time.

see u

I am having trouble with my new setup. 

I have a 7600K, MSI Z270 Gaming M5, GTX 1070.

I am unable to see SATA or NVMe drives. That and I cannot get the Nvidia Web Drivers to load. 

 

I've tried a handful of patches, SSDT-SATA from Rehabman, SATA-200-Unsupported.kext, and a handful others. The SATA controller is 8086:A282, which is apparently unsupported. I'm at my wits end as my first hackintosh with my skylake went beautifully. Hopefully someone can help me out here.

 

Here are the support files. I appreciate anyone's help they can offer!

Nvme, use pike patches

CLOVER superchase9000.zip

dear Mald0n please help me with DSDT,

my info

i5 7500

ASUS B250-Plus

GTX1060 6G

 

this is my files

if u use HS, check patch USB for HS in config.plist

CLOVER angel88.zip

Hey MaLd0n, thank you for your work , it helped me a lot. I use your DSDT file on my hackintosh, but I thought maybe I need a patch because I don't have the same MotherBoard. Here is my config : 

 

MB : MSI Z270 SLI Plus

CPU : Intel 7700K 4.2 GHz

GPU : Inno3D GeForce GTX 1060 6GB

RAM : Kingston HyperX Fury 2x8 Gb in 2666MHz

OSX : 10.12.6

 

The DSDT is a thing a don't understand so much , so I just take your file and put it into ACPI/Origin

 

Thank You.

i need ur table

check first post

 

Hi MaLd0n here is my zip file and please help me on the DSDT. I couldn't get my sound to work.

 

Thanks

 

my pc is as blow:

 

MB: MSI-Z270-TOMAHAWK-OPT-BOOST Bios 3.10

CPU: i7-6700K

RAM:16G x2

VGA: Nvidia GTX750 TI

Sound: ALC892

 

CLOVER Li Tan.zip

if dont work need use other id

Hey again MaLd0n, I just have issues with my ALC1220 audio. I try all way to get it : Lilu , VoodooHDA , Toleda's way. And there is nothing who works. If you can help me it will be nice. 

 

MB : MSI Z270 SLI Plus

CPU : Intel 7700K 4.2 GHz

GPU : Inno3D GeForce GTX 1060 6GB

RAM : Kingston HyperX Fury 2x8 Gb in 2666MHz

OSX : 10.12.6

 

Thank you ! 

CLOVER Delecta.zip

Hello MaLd0n, thanks for this guide.

 

I have a problem with speed of the lan controller, if i transfert a big file from my nas the data speed is average 22MB/s, but the lan negotiation is 1000 in the Sierra setting and the led of my gibagit switch is green (1000).

 

If i transfert the same file with Windows  or Ubuntu the data speed is 80-90MB/s.

 

I have used the kext in first page:

http://www.insanelymac.com/forum/files/file/313-atherose2200ethernet/

 

My mainboard is GA Z270 Gaming K3

 

You can help me please?  ^_^

;) done

Hi Maldon,

 

I'm getting ready to go to High Sierra.

can I leave you here the clover to make it compatible?

 

My specs :

 

- Asus Rog Strix Z270G Gaming

- i7-7700K

- 16GB DDR4

- Nvidia 1080ti

- Wifi+Bt Broadcom BCM943602CS with pci card

- Nvme Samsung 256GB

 

 

At this time I am using the DSDT.aml from the old main board Z270i Strix...

 

:)

 

Thnks Sir!

just use usb port limit for high sierra and update kexts like applealc ;)

Hello Maldon,

 

 

All resolved. Fix DSDT. I put my clover configuration with DSDT and SSDT

 

 

I have

GA-z270x-ud5

32Gb Memory

500 SSD 850 EVO M2

255 SSD 830 

GC-Alpine ridge

radeon 580x 4gb

LG 5K with full 5k resolution + webcam + sounds + mic

all USB3/USB2 port working

Bluetooth and Wifi Works

DSDT.marlboro Lights.zip

Hi again MaLd0n. I changed some hardware in my rig. Could you do your magic?

 

Asus Z270M-plus

Intel 7600K

Geforce 1060 3GB

 

Amazing work! Thanks in advance!

 

EDIT. I managed to edit my DSDT after reading a lot. Thanks anyway!

DSDT.lolost.zip

Hey MaLd0n, Awesome guide, thank you so much, here are my clover files+ACPI+IORegistry.

My specs are the following:

 

Mobo: GA-Z270-HD3P Rev 1.0 Bios F7

CPU: i5 7500

GFX: Gigabyte GT 1030 OC 2GB

Ram: 1x16GB

Storage: Kingston SSD 120GB for system and i will throw in another 2TB HDD as soon as I'm done with the system setup

 

I installed El Captain 1st and then upgraded using the app store so that i can have the final update of Sierra with kabylake support, after installing Sierra, i removed fakeCPU ID, and changed my smbios to 18,2 as that specific model uses the same CPU that i have at the moment, so i don't really understand, do i need any PM hacks, or is my CPU OOB?

 

Here are the files you requested, can't wait to have this beast up and running, I've been on 10.8.5 on a C2Q Q6600 for the past couple of years.... lol (might upgrade it to El Captain using your other guide :)

 

attachicon.gifSend to Maldon.zip

CLOVER SLim Nasr.zip

welcome

Hi. I just built the pc in the signature.

I installed high sierra, so if you can't help me can you please show where are the patches you list in the first post?

It works, but i thinks it's not perfect and i'm not able to edit my dsdt properly as i did with my laptop.

Thanks!

Check usb port limit patch in config.plist

CLOVER Paolo7297.zip

Thanks for your guide. I, too would like to know about your patches. If you could post them I would try to patch my own myself. :)

 

 

Board: Z270N Gaming 5

Ram: 16gb

CPU: 7700k

GPU: MSI 1060 6gb OC

 

Attached is the disassembled (and assembled) DSDT and SSDTs along with my Clover sans the theme folder.

Thank you for taking the time to look at it.

CLOVER TrustAugustus.zip

So I followed everything and have a working system!

I dont suite understand the DSDT, but I have done everything else.

 

MOBO: GA-Z270X-UD5

CPU: i7700k

GPU: 1080 Ti

 

OS: 10.12.6

 

Clover Folder:

https://www.dropbox.com/s/ynraiilcxezaqwg/CLOVER.zip?dl=0

 

"Send me file"

https://www.dropbox.com/s/9oku4sftx9hjduc/Send%20me%20superflex%E2%80%99s%20iMac.zip?dl=0

 

Ioregistry:

https://www.dropbox.com/s/n98vs3wc1w5om76/ioregistry.ioreg?dl=0

 

thank you so very much for making this possible!

 

 

Edit. The only issue im experiencing, is that 1 disk doesnt show up after reboot. When i shut down, and power on again, all disks are back.. How come?

CLOVER lecycliste.zip

Hi it would be awesome if you could help me out as well.

 

On High Sierra

 

I got a i7 7700k @5100mhz on a

GA z270-UD5.   F5 BIOS

16gig 3000mhz

and a 

GTX1070

 

Getting some proper mA to the USB would be epic.

 

I hope I added all necessary files.

 

Mille Grazie

CLOVER blackbird_n1.zip

Hi sir Maldon

 

I built a hackintosh

my specs MB GA-B250M-D3H

Cpu Core i5 7500 intel HD 630

send me clover UEFI for installation macOS Sierra and 

post installation advise

 

Thanks in Advance.

same procedure

CLOVER majoract100.zip

use 10.12.6 or High Sierra

Hi MaLd0n. If you would be so kind as to help me I would really appreciate it! Thanks for all that you do around here. My build is in my signature.  :)

CLOVER leon.blackmail.zip

--------------------------------------------------------------

 

tomorrow i'll check others topics

see around guys/ladies

Share this post


Link to post
Share on other sites

 

just use usb port limit for high sierra and update kexts like applealc ;)

 

 

Please I have updated the bios and the old dsdt I had done was for a different motherboard (before I had z270i I Z270G)

 

I'd ask the courtesy to give me a new dsdt as follows (see my signature)

 

- Mobo : Asus Z270G

- Video : Nvidia 1080Ti

- Wifi+BT : pci card 

 

currently with the config of clover I can use HighSierra but I notice a slight "lag" and do not know what is due 

 

 

THHHHAAAAANKS!

 

PS: in the folder of clover (in origin) all aml extracted with F4

CLOVER.zip

Send me iMac di UltraLaser.zip

Share this post


Link to post
Share on other sites

 

Hello MaLd0n !
I have changed the motherboard with Gigabyte GA Z270 Gaming K3 + Gtx 1070 .Please help me.
thank you very much. ( High Sierra )

PS:in the folder of clover (in origin)all aml extracted with F4 

 


High’s iMac.ioreg


 

    RunMe.app - Send me High’s iMac.zip

EFI.zip

High’s iMac.ioreg.zip

Send me High’s iMac.zip

Share this post


Link to post
Share on other sites

Please I have updated the bios and the old dsdt I had done was for a different motherboard (before I had z270i I Z270G)

 

I'd ask the courtesy to give me a new dsdt as follows (see my signature)

 

- Mobo : Asus Z270G

- Video : Nvidia 1080Ti

- Wifi+BT : pci card 

 

currently with the config of clover I can use HighSierra but I notice a slight "lag" and do not know what is due 

 

 

THHHHAAAAANKS!

 

PS: in the folder of clover (in origin) all aml extracted with F4

CLOVER UltraLaser.zip

 

Hello MaLd0n !
I have changed the motherboard with Gigabyte GA Z270 Gaming K3 + Gtx 1070 .Please help me.
thank you very much. ( High Sierra )

PS:in the folder of clover (in origin)all aml extracted with F4 

 

High’s iMac.ioreg

 

    RunMe.app - Send me High’s iMac.zip

 

CLOVER gagaraz.zip

Share this post


Link to post
Share on other sites

Hi MaLd0n. I Updated Bios to version F7( High Sierra) .If you would be so kind  to help me . Thanks in Advance

Archive.zip

Share this post


Link to post
Share on other sites

 

Thanks again, i shall give it a try later tonight and let you know how it goes with bench scores.

 

Keep an eye on your 775 El Capitan guide, i shall upgrade my old machine as soon as this one is up and running :D:yes:  :angel_not: 

Share this post


Link to post
Share on other sites

Hi MaLd0n. I Updated Bios to version F7( High Sierra) .If you would be so kind  to help me . Thanks in Advance

if u have a stable system and bios, dont need update bios, just gain ur money and enjoy ur hack :D

DSDT.IUTniun.zip

Thanks again, i shall give it a try later tonight and let you know how it goes with bench scores.

 

Keep an eye on your 775 El Capitan guide, i shall upgrade my old machine as soon as this one is up and running :D:yes:  :angel_not:

welcome

enjoy

Share this post


Link to post
Share on other sites

Hi again!

Everything works perfectly except for a couple of things. 

The computer seems to wake itself randomly and stick on a black screen. I then have to force reset  and when I reset it is in hibernate at the clover menu. 

Also, my thunderbolt device seems to only work sometimes, and I need to power it on right as I power on the computer.

Is there anything I can do to fix these issues?

Thank you!

Share this post


Link to post
Share on other sites

if u have a stable system and bios, dont need update bios, just gain ur money and enjoy ur hack :D

attachicon.gifDSDT.IUTniun.zip

welcome

enjoy

You are amazing, thank you very much.

Share this post


Link to post
Share on other sites

lol

clover have a very basic patches, all hacks need a good edited DSDT ;)

check clover page and see slice talkin' about it

create patches with datasheet, ioreg and tables real macs and tests, many tests and time.

see u

Nvme, use pike patches

attachicon.gifCLOVER superchase9000.zip

if u use HS, check patch USB for HS in config.plist

attachicon.gifCLOVER angel88.zip

i need ur table

check first post

attachicon.gifCLOVER Li Tan.zip

if dont work need use other id

attachicon.gifCLOVER Delecta.zip

;) done

just use usb port limit for high sierra and update kexts like applealc ;)

attachicon.gifDSDT.marlboro Lights.zip

attachicon.gifDSDT.lolost.zip

attachicon.gifCLOVER SLim Nasr.zip

welcome

Check usb port limit patch in config.plist

attachicon.gifCLOVER Paolo7297.zip

attachicon.gifCLOVER TrustAugustus.zip

attachicon.gifCLOVER lecycliste.zip

attachicon.gifCLOVER blackbird_n1.zip

same procedure

attachicon.gifCLOVER majoract100.zip

use 10.12.6 or High Sierra

attachicon.gifCLOVER leon.blackmail.zip

--------------------------------------------------------------

 

tomorrow i'll check others topics

see around guys/ladies

Hi! i tried and got the screen attached repeating continuosly... I don't know what to do...

Can you send me the patches you use? I cannot find them...

Thanks a lot!

post-969329-0-06699300-1507847597_thumb.jpg

Share this post


Link to post
Share on other sites

Hi Mald0n!

 

the system is almost perfect! does not work only the sleep mode (stop)

What could it be? Anyway thank you so much for everything!

what happens with sleep?

try a darkwake?

Hi again!

Everything works perfectly except for a couple of things. 

The computer seems to wake itself randomly and stick on a black screen. I then have to force reset  and when I reset it is in hibernate at the clover menu. 

Also, my thunderbolt device seems to only work sometimes, and I need to power it on right as I power on the computer.

Is there anything I can do to fix these issues?

Thank you!

disable auto sleep

TH, hot plug dont work, power ur computer with device connect

Hi! i tried and got the screen attached repeating continuosly... I don't know what to do...

Can you send me the patches you use? I cannot find them...

Thanks a lot!

use a fresh install, just install clover and replace folder

MaLd0n You are amazing!!!

attachicon.gif未命名.jpeg

welcome

enjoy

Share this post


Link to post
Share on other sites

is a kext inject problems, use kexts in LIbrary/Extensions

 

Hmmm very strange, I tried without dsdt.aml and the sound card is seen. Might be something in dsdt.aml?

else: could you tell me what is the kext to patch for my ahci controller? :)

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   1 member

  • Similar Content

    • By tonyx86
      I was inspired by @duduclx post here for installing El Capitan on a Dell Latitude E6410, so I decided to install Mojave 10.14.5 and subsequently 10.14.6.  Everything works perfectly (including sleep).  I'm starting this thread hoping to help others install Mojave on their E6410s.  A brief installation guide is provided later in this first post.  The interested reader is encouraged to read the other posts in this thread to see how this solution evolved and to learn additional tips/details not provided in this first post (including dual-booting with macOS and Windows).
       
      My system is as follows:
      Dell Latitude E6410 (I7-620m, Nvidia 3100M, 8GB DDR3, 512GB SSD, 1440x900 display, BIOS: A17) MacOS: Mojave 10.14.6 (APFS) (Patched with DosDude Mojave Patcher 1.3.3) MacModel: MacBookPro 6,2 (LPCB._DSM.Name "pci8086,3b09") Kexts: Lilu 1.3.6, VoodooHDA 2.9.2, AirportBrcmFixup 2.0.0, IntelMausiEthernet 2.4.1d1, ACPIBatteryManager 1.90.1, BrcmPatchRam2.kext, BrcmFirmwareRepo.kext, VoodooPS2Controller (the "Refined ALPS Touchpad" version - release 6 developed by @Dr. Hurt and compiled by @bronxteck), not the original version), USBInjectAll (with custom SSDT-UIAC), VoodooSDHC.kext (configured as shown here). Wi-Fi: Broadcom BCM 94352HMB (with AirportBrcmFixup.kext) CLOVER (Legacy): R4961  
      Configuration items that may be different from what you have seen in other E6410 configurations
      Addition of _OFF and _ON methods to _PTS and _WAK methods respectively (to control discrete graphics in order to enable sleep/wake) LPCB._DSM patched with device-id "3b09" AND "name", "pci8086,3b09" for native Nehalem power management with MacBookPro 6,2 ECDV renamed to EC so that AppleBusPowerController loads AGP.VID._DSM patched with device-id "0a29" so that AppleGraphicsPowerManagement loads No CLOVER Generate P or Generate C States (with the correct LPCB._DSM and MacBookPro 6,2, these CLOVER options are unnecessary for this architecture and only limit max multiplier and reduce number of P states) DSDT patched to include HDAU device (device-id 0x0be3)  
      What is NOT working:
      Display brightness can be controlled with keyboard keys, but cannot be controlled with slider in Display settings. Graphics Power Management - AGPM loads (because 10de,0a29 device is injected), but there's no evidence that 3100m frequency and voltage is changing.
        What is NOT tested:
      Smartcard Reader eSata (I have this disabled in my BIOS) Firewire Port (it does appear in the Network settings, just haven't tried it) Microphone Jack PC Card Slot (I have this disabled in my BIOS)  
      What IS working:
      SLEEP IS WORKING! Everything else not mentioned above.   Speedstep/CPUPowerManagement is perfect, system temps are low, CPU multiplier operates as expected, battery life is long Shutdown is fast Display/graphics acceleration is perfect (thanks to DosDude's Mojave patcher) Brightness (adjusted with brightness keys on keyboard) works perfectly Battery Manager works (battery status is displayed in menu bar) simply by installing ACPIBatterManager.kext. Wi-Fi (after changing to Broadcom BCM94352HMB and installing AirportBrcmFixup.kext) Audio (volume adjustable, volume indicator appears in menu bar).  Switched to VoodooHDA from AppleALC after AppleALC caused slow boot due to "IOHDACodecFunction timeout." Ethernet port (with IntelMausiEthernet.kext) Broadcom BCM20702A0 Bluetooth (with BrcmPatchRam2.kext and BrcmFirmwareRepo.kext) Optical Drive External VGA (with corrected NVCAP.  Need NVCAP 04000000 00000100 0E000000 00000007 00000000 (credit: here) for working external VGA display. Headphone jack Display Port (tested using DP > HDMI adapter) Camera SD Card Reader  
      Known issues and their solutions (These issues have all been resolved, with the solutions incorporated into the attached config files.  The issues are listed here for historical purposes and no further work is needed unless stated otherwise).
      AAPL,clock-id and device_type do not appear in IORegistry for EHC1.  Solution is to use CLOVER on-the-fly patching/fixing/renaming for EHC1 and EHC2.  Thank you, @feartech, for this tip. ALPS trackpad performance is not good with the "standard" VoodooPS2Controller.kext that I initially used.  Switching to the "Refined ALPS TouchPad driver" is a big improvement.  I've implemented and tested this on my system.  The ALPS version of VoodooPS2Controller.kext mixes up a few keys.  Need to switch the Command and Option keys (System Preferences > Keyboard > Modifier Keys) and change keyboard type to ISO European. This configuration (captured in the attached config files) uses an injected device-id (10de,0a29) for NVidia 3100m to get AGPM to load.  While I haven't observed any performance differences, a better approach may be to inject AGPM properties for device 10de,0a6c (the actual device-id for the 3100m).  This AGPM method is discussed later in this thread.  I have briefly tested this "FakeSMC.kext method" for injecting AGPM attributes without any noticeable changes in laptop/graphics behavior. IOHWControl is not loaded under AGPM (Should be AGP > VID > NVDA,Display-A@0 > NVDATesla > AGPM > gpu-control > IOHWControl as viewed in IORegistryExplorer).  It is loaded on a real MacBookPro6,2 running Mojave and is loaded on this Dell Latitude E6410 running High Sierra.  If I "Inject NVidia" via CLOVER, IOHWControl loads properly. The Dell Latitude DSDT (BIOS A17) has a bug in Method (GNOT).  In the method, the expression  If (LOr (LGreater (OSYS, 0x07D0), LLess (OSYS, 0x07D6))) always evaluates to TRUE, so the patched DSDT has no dependency on the value of OSYS.  I suspect that LOr should be replaced with LAnd, so that this expression is TRUE for variants of Windows 2001 and False for any other OS.  While this may have no affect on MacOS, it makes one wonder how such an obvious bug made it through Dell QA and is still present in BIOS A17.  Also makes one wonder whether the sleep problem (which no one has solved) was fixed in Windows to address another DSDT bug. The assigned value of ACOS and OSYS in the DSDT are conditional on the operating system.  There is no condition for "Darwin."  The solution is to add a condition for "Darwin" (making it equivalent to one of the defined operating systems (e.g. Linux, Win7, etc).  The attached config hard-codes ACOS and OSYS values equivalent to those for Linux.  Another way to handle this (different from the method employed in the attached config files) might be to override _OSI with XOSI (defined in a custom SSDT). The portType of the Internal Bluetooth device is portType=0 which, according to Rehabman's comments in SSDT-UIAC-All.dsl, is an external USB 2 port.  This should be an internal USB port (portType=2).  I learned through trial and error that the HUB1 and HUB2 definitions in Rehabman's SSDT-UIAC-ALL.dsl apply to the ports on the EHCx USB hubs.  The solution is to include the HUB1 definition in SSDT-UIAC.dsl and change portType to 2 for HP15.  This change doesn't appear to affect/fix sleep, but it may prevent instant wake if we get sleep working. There are minor differences between a real MacBookPro6,2 IORegistry dump and this HackBookPro6,2 IORegistry dump that can be resolved with simple DSDT edits.  I am now running with these changes, but haven't found these changes to make any difference in operational behavior.
      Rename Device (AC) -> Device (ADP1) Remove UID from Device (HPET) Add compatible ID "PNP0C01" to Device (HPET) Change ADP1:_STA from 0x0F to 0xFFFFFFFF Enable Ambient Light Sensor and renamed to Device (ALS0) from Device (ALS) Add compatible ID "smc-als" to ALS0 Rename LID -> LID0 Change "name" definitions to Buffers in _DSM methods Rename Device (PBTN) to PWRB Rename Device (SBTN) to (SLPB) Change HDAU.hda-gfx from "onboard-1" to "onboard-2" Change GFX0.hda-gfx from "onboard-1" to "onboard-2" Sleep / Wake does not work with the basic DSDT edits.  I have discovered that Sleep / Wake can be made to work by adding discrete graphics _OFF and _ON methods to _PTS and _WAK methods respectively (borrowed the concept and code from a working E6430 DSDT: Credit here: https://osxlatitude.com/forums/topic/9248-working-sleep-on-intel-hd-and-nvidia-nvs-on-dell-latitude-e6430-optimus-enabled-or-disabled/page/6/. LCD screen is blank when waking laptop by opening lid (screen is not blank when waking with power button).  Solution is to add darkwake=8 to CLOVER boot args.  Thank you @Hervé for this tip.  
      Brief Installation Guide:
      Configure BIOS (version A17) as follows (leave default unless listed here): Boot Sequence: USB, Internal HDD, CD/DVD, Modular Bay HDD; Boot List Option: Legacy; Integrated NIC: Enabled; Parallel Port: Disabled; Serial Port: Disabled; SATA Operation: AHCI; Misc Devices: Enable Modular Bay, Camera, External USB, Microphone, Media Card and 1394; Latitude ON Reader: Disabled; Keyboard Illumination: Auto ALS and Input; Ambient Light Sensor: Enabled; OROM Keyboard Access: Disable; TPM Security: Disable; Computrace: Deactivate; CPU XD Support: Enable; Performance: Enable all options; Power Management: Disable Wake on AC, Disable Wake on LAN/WAN, Express Charge: Standard, Charge Behavior: Enabled; Keypad: Fn Key Only; Mouse/Touchpad: Touchpad/PS-2 Mouse; USB Emulation: Enable Legacy; Fn Key Emulation: Disabled; Fastboot: Thorough; Virtualization: Enable Intel Virtualization, Disable VT for Direct I/O, Disable Trusted Execution; Wireless Switch: Bluetooth and WLAN; Wireless Device Enable: Bluetooth and WLAN;  Create your MacOS installer USB (Use DosDude's Mojave Patcher for Mojave) (start with High Sierra and not Mojave if you're new to hackintosh). Install CLOVER (Legacy) on installer USB using attached EFI as your guide for patched ACPI, kexts and config.plist Install MacOS to your SSD.  When you run DosDude's Mojave Patcher, DO NOT install LegacyUSBInjector.kext - you're going to use Rehabman's USBInjectAll.kext.  Also, do not install the DosDude SIP kext (you're using CLOVER to manage SIP). Install the following kexts in /Library/Extensions:  ACPIBatteryManager.kext, AirportBrcmFixup.kext, BrcmFirmwareRepo.kext, BrcmPatchRAM2.kext, FakeSMC.kext, FakeSMC_ACPISensors.kext, FakeSMC_CPUSensors.kext, FakeSMC_GPUSensors.kext, FakeSMC_LPCSensors.kext, IntelMausiEthernet.kext, Lilu.kext, USBInjectAll.kext, VoodooPS2Controller.kext (the "Refined ALPS Touchpad driver," not the original), VoodooSDHC.kext (configured as shown here). Switch Command and Option keys to compensate for Refined ALPS driver issue (System Preferences > Keyboard > Modifier Keys).  Also change keyboard type to ISO European to fix the [ ` ~ ] key (to the left of the "1" (one) key. Install VoodooHDA Install HWMonitor application  
      Tips for Improved Performance (on this and other older systems)
      System Preferences > Spotlight > Search Results: Uncheck all options System Preferences > Spotlight > Privacy: Add all Volumes System Preferences > Accessibility > Display: Check "Reduce motion" System Preferences > Accessibility > Display: Check "Reduce transparency"  
      Other tips
      If your fan is always running and temps are good, try pressing Fn + z After applying Mojave updates, HWMonitor may not display discrete graphics attributes.  On systems with multiple displays, a second (or third display) may not be active after applying the Mojave update.  The solution to this is to run "sudo kextcache -i /" (in a terminal window) and reboot.  This will usually fix the issue.  If the issue is not fixed, run DosDude's Post Install Utility, apply the Legacy Graphics Patch, reboot and then run "sudo kextcache -i /" if necessary.  
      Credits
      In addition to those mentioned in this first post and in subsequent posts in this thread, much of this solution for the Latitude E6410 was made possible by the numerous contributions of @RehabMan.  I hope he's doing well, wherever he is.  Hopefully he has long since forgotten what a PIA I was (and still am) as I was (and still am) learning hackOS.

      E6410.zip
    • By gusbemacbe
      Hello,
       
      I am a former user of MacBook and Mac mini. Both died. One in 2014 and another last year.  I will think of giving my Hackintosh-compatible laptop to my brother that I purchased years ago, because he wants to play more than one computer, so he is a Twitch/YouTube streamer and a hardcore gamer and I will not need to lend him many times. If he wants, from my former laptop I will take only one 240GB SSD Samsung Evo with installed Arch Linux and leave one 500GB HDD for him. In the future, I will purchase a new Alienware laptop.
       
      As I got newly graduated, I moved to a new super PC with AMD Ryzen™ 7 2700X CPU and with NVIDIA GeForce™ 1660 Ti GPU. More details, you can see my signature below, that provides the complete details. I own an external SSD m.2 2280 with installed Windows 10.
       
      I will reconsider purchasing 4th drive – an external 480GB SSD m.2 2280 SATA WD Green 545MB/s or an external 1TB SSD SATA WD Green 545MB/s – for installing Hackintosh. But purchasing, I need to make sure.
       
      1. Is it worth to install Hackintosh on an external SSD m.2 2280? If I partition two partitions, one for Insansely's MyHack/Chameleon/Clover and another for Hackintosh and my new super-PC boot is natively BIOS and Grub, is it worth? Maybe I will try to install reFind on Arch Linux to replace the Grub if it is worth.
      2. I know that it will run on macOS High Sierra, Mojave and Catalina, but if I need Metal 2 to run the latest version of Sketch (the which I own an original licence) and of other apps the which I own original licences? Is NVIDIA GeForce™ 1660 Ti compatible with Metal 2?
      3. Since it be an external SSD, will I able to run Hackintosh as a portable OS in other computers?
       
       
    • By verdazil
      This is not intended to be a complete and comprehensive installation guide. There are many installation guides on the forum and installing macOS is no different from installing on other desktop builds. Rather, this is supplemental information specific to the my hardware listed below. I hope you find this information useful and this will save you a little time.
       
      Hardware
      MB: Huananzhi X79-ZD3
      CPU: Intel® Xeon E5-2689, 1.2-3.6 GHz
      Chipset: Sandy Bridge-E Q65 (C600/C200)
      Memory: Samsung 4x8 Gb ECC/REG DDR3, 1866 MHz
      Video: Saphire Nitro+ Radeon RX 590
      Monitor: BENQ-BL2711U + LG TV 42LF650V
      SSD + HDD: NVMe M.2 Samsung 970 EVO 250 Gb + HDD Seagate 2 Tb
      WiFi: Fenvi FV-T919 BCM94360CD
      Mac model: MacPro6,1
      MacOS version tested: Mojave 10.14.6 (18G1012)
       
      What works?
      - Video: 4K x 60Hz on BENQ-BL2711U + Full HD x 60Hz on LG TV 42LF650V
      - Sound: audio jack + HDMI audio on both monitors
      - Wi-Fi (out of the box)
      - USB2 && USB3 ports
      - LAN
      - Bluetooth (out of the box)
       
      What does not work?
      - Sleep mode: not tested / I don't need
       
      BIOS Configuration, what's important:
      Bios Version: 4.6.5.4
      Legacy USB Support: [Enabled]
      XHCI Hand-off: [Enabled]
      EHCI Hand-off: [Enabled]
      USB Mass Storage Driver Support: [Enabled]
      Hyper-threading: [Enabled]
      Active Processor Cores: [All]
      Serial Port: [Disabled]
      Intel(R) VT-d : [Disabled]
      Launch CSM: [Enabled]
      Boot option filter: [UEFI only]
      Launch Storage OpROM policy : [UEFI only]
      Launch Video OpROM policy : [UEFI only]
       
      Here is what I used to install and configure the system:
      Clover: make with Clover Builder https://github.com/Dids/clover-builder/releases Audio: https://github.com/vit9696/AppleALC Video: https://github.com/acidanthera/WhateverGreen/releases USB: https://bitbucket.org/RehabMan/os-x-usb-inject-all/downloads + PMHeart/DalianSky patches LAN: http://www.insanelymac.com/forum/topic/287161-new-driver-for-realtek-rtl8111/ CPU Power management: https://www.insanelymac.com/forum/topic/324270-sandy-bridge-e-ivy-bridge-e-power-management-1013-appstore-release   Clover configuration:
      Clover version: v2.5k r5088
      You can get the configuration file and the necessary kexts from the link at the end of the message
      Note: you must insert your own SeralNumber && MLB && ROM && SmUUID in the config.plist file.
       
      How to use
      To make a bootable flash drive, you can use my EFI directory (link at the end of the message). Tested for Mojave 10.14.6 installation.
      https://drive.google.com/file/d/1tjbwuUWg_PlQCVt5PTRFG6HsNby_BcgN
    • By hackinhacker
      First time trying hackintosh.  Upon Mojave (10.14.6) installation on my pc, it first reboots then goes to panic state...  Here is my BIOS settings, config.plist, and list of kexts.  Can someone please help?  
       
      my machine spec:
       
      MOBO:  Gigabyte Z390 Pro 
      CPU:  i5 9600k
      GPU:  Sapphire Radeon Pulse RX 570 4GB
      Memory:  Crucial 2 X 16GB 2666 Mhz
       
      BIOS setting
      • Save & Exit → Load Optimized Defaults
      • Chipset → Vt-d → Disabled 
      • Chipset → Internal Graphics → Disabled
      • Chipset → Above 4G Decoding → Disabled 
      • BIOS → Windows 8/10 Features → Other OS
      • BIOS → CSM Support → DISABLED  
      • Initial Display Output → PCIe 1 Slot
      • Trusted Computing → Security Device Support →  Disable
      • USB Configuration → Legacy USB Support →  Enabled
      • USB Configuration → XHCI Hand-off →  Enabled
      • Network Stack Configuration → Network Stack →  Disabled
      • SATA And RST Configuration → SATA Mode Selection →  AHCI
      • Extreme Memory Profile (X.M.P) → Disabled ( Optionally, can be enabled after macOS is installed, your choice )
       
       
      config.plist.1211.plist.zip
      kext.zip

    • By ludufre
      Installing macOS Catalina 10.15.2 on Asus VivoBook S400CA
       
       
      There are several versions of this laptop.
       
      These are the versions I've seen so far:
      - S400CA-BRA-CA206H = i3-2375M with ALC269VB
      - S400CA-BRA-CA178H = i5-3317U with VT1802P
       
      I believe that all models are practically identical except the variations i3 and i5 that have particularities, because one is Sandy Bridge platform and another Ivy Bridge.
       

      Changelog:
       
      12/11/2019 04:35h GMT-0
      - Added update 10.15.2 instructions.
       
      11/11/2019 04:41h GMT-0
      - Merged Core i3 and i5 config.plist.
      Same SMBIOS now. Core i3 version need to remove: Devices - Properties - PciRoot(0x0)/Pci(0x2,0x0). - Just one USBPorts.kext now, since SMBIOS are same. 
       
      11/10/2019 20:41h GMT-0
      - Updated USB 3.0 injection. (Removed USBInjectAll.kext and SSDT-UIAC.aml and added USBPorts.kext)
      - Replaced AtherosE2200Ethernet.kext with version 2.3.0 RELEASE. (Previously was DEBUG build)
       
      11/10/2019 00:22h GMT-0
      - Added Battery's DSDT patch.
      - Fixed USB 3.0. (Replaced USB's DSDT patch, removed FakePCIID.kext and FakePCIID_XHCIMux.kext and added SSDT-EC.aml and SSDT-UIAC.aml)
      - Updated config.plist. (Removed PNP0C09 to PNPFFFF, not needed with SSDT-EC.aml)
       
      11/08/2019 14:33h GMT-0
      - First version.
       
      What works and what does not
       
      Core i3 Version specific
      - Processor: Intel Core i3-2375M ->  Work. All SpeedStep stages.
      - Video Card: Intel HD3000 ->  Work. QE/CI without Metal. (additional step bellow)
      - Audio: ALC269VB ->  Work. But no earphone. (more details)
       
      Core i5 Version specific
      - Processor: Intel Core i5-3317U ->  Work. All SpeedStep stages.
      - Video Card: Intel HD4000 ->  Work. QE/CI and Metal.
      - Audio: VT1802P ->  Work.
       
      Common
      - Chipset: Intel HM76 ->  Work.
      - HDMI ->  Work.
      - VGA ->  Not work. Normal.
      - WiFi/Bluetooth: Intel AC 3160 ->  Not work. Replaced with DW1560 / AW-CE123H.
      - Ethernet: Intel AR8161 ->  Work.
      - Card Reader: Unknow ->  Not work.
      - Keyboard and Touchpad ->  Work.
      - FN keyboards keys ->  Not work yet.
      - Webcam ->  Work.
      - Battery ->  Work.
      - Touch screen ->  Not work.
      - USB3.0 ->  Work.
      - Sleep ->  Work.
      - Airdrop, Handoff and Continuity ->  Work after replaced wireless.
      - Instant Hotspot ->  Not work even after replaced wireless.
       
       
      Todo
       
      - Make earphone work in Core i3 version.
      - Fix FN keyboard keys.
      - Convert DSDT patches to hotpatch.
      - Make touch screen work.
      - Make card reader work.
      - Make trackpad appear in System Preferences
       
       
      What you need to install

      - Running install of macOS
      - One USB flash drive of 8GB or bigger
      - macOS Catalina install app
      - Clover EFI
      - Clover Configurator
      - Some KEXTs and SSDT patches


      How create create the install flash drive
       
      Prepare install flash drive

      Format the flash drive with GUID partition mapping and name it "Install".

      - Open Disk Utility.
      - Click in View, then "Show All Devices".
      - Select the destination flash drive, then Erase.
      - Name: Install, Format: Mac OS Extended (Journaled) and Scheme: GUID Partition Map
       
      Create install flash drive

      Open terminal and run this command:
      sudo /Applications/Install\ macOS\ Catalina.app/Contents/Resources/createinstallmedia --volume /Volumes/Install --nointeraction This will take about 30 minutes.
       


      Install bootloader

      Download the CloverEFI from official repository (used 5098) and install only with these options on "Install macOS Catalina":
       
      - Install for UEFI booting only
      - Install Clover in the ESP
      - UEFI Drivers - Recommended Drivers - FSInject (I still don't know if it's really necessary)
      - UEFI Drivers - File System drivers - ApfsDriverLoader (Support to APFS partitions)
      - UEFI Drivers - File System drivers - VBoxHfs (Support HFS/HFS+ partitions)
      - UEFI Drivers - Memory fix drivers - AptioMemoryFix (Fix the memory management of de UEFI/BIOS)
      - UEFI Drivers - Additional drivers - CsmVideoDxe
       
      FileVault 2
       
      If you plan to use FileVault 2, you need to download additional drivers, since what comes with Clover is not up to date and use VirtualSMC instead of FakeSMC.
      Follow instructions bellow:
       
      From current Clover installation, check these options to USB keyboard/mouse work on password screen:
      - UEFI Drivers - Human Interface Devices - UsbKbDxe
      - UEFI Drivers - Human Interface Devices - UsbMouseDxe
       
      After Clover install will be created a partition named EFI and mounted in Desktop. Usually the path is /Volumes/EFI/.
       
      Download the versions 2.1.0 and 2.0.9 of AppleSupportPkg from: https://github.com/acidanthera/AppleSupportPkg/releases
      We need the last version of AppleGenericInput.efi that is inside 2.1.0 and last version of AppleUiSupport.efi that is inside 2.0.9.
      OR download attached bellow.
       
      Put in /Volumes/EFI/EFI/CLOVER/drivers/UEFI/
       
      That's it! FileVault 2 will work without problems.
       

       
       
      Make things works
       
      After Clover install will be created a partition named EFI and mounted in Desktop. Usually the path is /Volumes/EFI/.
       
      - Replace the /Volumes/EFI/EFI/CLOVER/config.plist with mine attached below according to your processor version.
      - Put all SSDT-*.aml attached below in /Volumes/EFI/EFI/CLOVER/ACPI/patched/
       
      Generate your Serial, MLB and SmUUID
       
      - Open the replaced config.plist with Clover Configurator (used 5.7.0.0)
      - Go to SMBIOS, click few times in "Generate New" in Serial Number and SmUUID.
       
      Core i3 version:
      - Go to Devices - Properties.
      - Remove: PciRoot(0x0)/Pci(0x2,0x0).
       
      Core i5 version:
      - Remove: /Volumes/EFI/EFI/CLOVER/ACPI/patched/SSDT-PWR.aml
       
      Copy the Clover Configurator to flash drive because you will need later.
       
      Download those Kexts and put in /Volumes/EFI/EFI/CLOVER/kexts/Other/
       
      - Download the VirtualSMC.kext, SMCProcessor.kext, SMCBatteryManager.kext and UEFI driver (put VirutalSmc.efi inside /Volumes/EFI/EFI/drivers/UEFI/). I used the version 1.0.9.
      - Download the Lilu.kext from here. I used the version 1.3.9.
      - Download the VoodooPS2Controller.kext from here. I used version 2.0.4.
      - Download the AtherosE2200Ethernet.kext from here. I used the version 2.3.0 compiled from source (attached below), but the release 2.2.2 works too.
      - Download the AppleALC.kext from here. I used the version 1.4.3.
      - Download the WhateverGreen.kext from here. I used the version 1.3.4.
      - Download the USBPorts.kext attached bellow to properly inject USBs.
       
       
      Keyboard swap Command with Option (optional)
       
      - If you prefer, you can swap Command and Option keys, to map Win Key - Command and Alt - Option.
      - Change /Volumes/EFI/EFI/CLOVER/OEM/S400CA/UEFI/kexts/10.15/VoodooPS2Controller.kext/Contents/PlugIns/VoodooPS2Keyboard.kext/Contents/Info.plist:
      <key>Swap command and option</key> <true/> to:
      <key>Swap command and option</key> <false/> Or, download the version 2.0.4 already adjusted attached bellow.
       
       
      Wifi and Bluetooth (DW1560 / AW-CE123H)
       
      After replaced the wireless card. Download those Kexts and put in /Volumes/EFI/EFI/CLOVER/kexts/10.15/
       
      - Download the AirportBrcmFixup.kext from here. I used the version 2.0.4. (To enable Wireless)
      - Download the BrcmBluetoothInjector.kext, BrcmFirmwareRepo.kext and BrcmPatchRAM3.kext from here. I used the version 2.5.0. (To enable Bluetooth)
      - Download the BT4LEContinuityFixup.kext from here. I used the version 1.1.4. (To enable Handoff and Continuity)
       
      Keep in mind that the bluetooth kexts are currently in development and the official releases will be available in future in the repository: https://github.com/acidanthera/BrcmPatchRAM/releases
       
      Now you can start the installation without problem (I guess).
       
       
      How install
       
      UEFI Setup Configuration and Installation

      UEFI configuration
       
      My BIOS is the latest: 210
       
      - Shutdown and insert the flash drive.
      - Power on with F2 pressed to enter BIOS setup.
      - Change value: Advanced - Intel Virtualization Technology to DISABLED
      - Change value: Advanced - Intel(R) Anti-Theft Technology Configuration to DISABLED
      - Save & Exit Setup (F10)
       
      - Now, hold the ESC
      - In the list, select your flash drive.
      - Choose the flash drive (white icon).
       
      The installer will start. 
      
      Format destination disk

      Format the disk with GUID partition mapping and name it "Macintosh".

      - Select Disk Utility in the list, then press Continue.
      - Click in View, then "Show All Devices".
      - Select the destination Disk, then Erase.
      - Name: HD, Format: APFS and Scheme: GUID Partition Map

      Close Disk Utility.
      
      Select "Install macOS", then Continue.
      Follow instructions in screen.

      After install

      After first part install the system will reboot. Maybe you have to press ESC again and select the flash drive.
       
      Choose the internal disk (gray hdd icon) if not already selected.

      The second part of the installation will begin. This will take 16 minutes.
       

      Post installation
       
      Bootloader

      When the second part of install finish, the system will reboot again.

      After performing the user initial setup and go to the desktop, you need to make the system disk bootable.

      Open the Clover Configurator from flash drive that you copied before.

      Mount and open the flash drive EFI partition. (Inside Clover Configurator, Mount EFI -> Select flash drive in Efi Partitions list -> Mount Partition -> Open Partition)
       
      Copy the EFI folder to desktop.
       
      Go back to Clover Configurator, unmount the EFI partition of the flash drive and mount and open the EFI partition of internal disk.
       
      Move the EFI folder from Desktop to EFI partition of the internal disk.
       
      Eject the flash drive.
       
      Move all Kexts from EFI partition of internal disk to /Library/Extensions and make kext cache, with those commands in Terminal:
      sudo mv -R /Volumes/EFI/EFI/CLOVER/kexts/10.15/* /Library/Extensions/ sudo chmod -R 755 /Library/Extensions sudo chown -R root:wheel /Library/Extensions sudo kextcache -i / Restart the system.
       
      If you go directly to BIOS you have to add Clover entry manually:
       
      - Go to "Boot" and press "Add New Boot Option".
      - Select "Add boot option", write CLOVER and press Enter.
      - In "Select Filesystem", choose the option that contains "HD". Like "PCI(1F|2)\DevicePath(Type 3, SubType 12)HD(Part1,Sig2a0127c1-ea5d-44d3-8967-57e59c1f0e3b)".
      - Select "Path for boot option", write EFI\BOOT\BOOTX64.efi and press Enter.
      - Select "Create" and press enter.
      - Go to "Save & Exit" and select "Save Changes and Exit".
       
      Intel HD 3000 - Core i3 version only
       
      If you have the i3 version with HD 3000 iGPU you have to do an additional step:
       
      - Download latest Legacy Video Patch from: https://github.com/chris1111/Legacy-Video-patch/releases
      - Always use the version compatible with your current Catalina build!
      - Run the installer and reboot.
      - Graphics acceleration now works. But you'll have some rare artifacts because of lack support of Metal.
       
       
      Battery, USB & Sleep DSDT patch
       
      First we need dump current DSDT/SSDT tables:
      - Restart.
      - On Clover menu, press F4 to dump.
      - Select internal disk and start normally.
       
      Prepare files:
      - Open the Clover Configurator from flash drive that you copied before.
      - Mount and open the internal disk EFI partition. (Inside Clover Configurator, Mount EFI -> Select internal disk in Efi Partitions list -> Mount Partition -> Open Partition)
      - Navigate to EFI/CLOVER/ACPI/origin/.
      - Copy DSDT.aml to EFI/CLOVER/ACPI/patched/.
      - You'll have DSDT.aml, SSDT-EC.aml, SSDT-PWR.aml (if Core i3 version) and SSDT-PNLF.aml in EFI/CLOVER/ACPI/patched/.
       
      Apply patches to DSDT.aml:
      - Download the MacIASL from here. I used the version 2018-0507.
      - Open the DSDT.aml from patched/ with MacIASL.
      - Click in "Patch" button.
      - Paste and "Apply" each patches below.
       
      Battery patch
      #Maintained by: RehabMan for: Laptop Patches #battery_ASUS-N55SL.txt # created by RehabMan 8/12/2013 # created originally for jesselid # works for: # ASUS N55SL, BIOS rev. 204 # ASUS VivoBook series # ASUS Zenbook UX31A # ASUS UX301LA # ASUS X553E-SX399V # ASUS F501A # ASUS K55VM # ASUS U46SV, BIOS rev. 2.04 # ASUS N43 # ASUS PU500CA (90NB00F1-M01120) # ASUS N73SV # ASUS X401A-WX108 # ASUS F551CA Bios rev. 207 # ASUS S551LB VivoBook # ASUS ZenBook UX32VD # ASUS ZenBook UX32V # ASUS F550L-X455H # ASUS X53S # ASUS K550JD-XX003H # ASUS G53SX # ASUS K56CB # ASUS UX305 # ASUS N550LF (per gabberZ) # ASUS TP300LA # ASUS X200LA # ASUS TP500LA (per haimann951) # ASUS U46E (per jacopers) # ASUS N550JK (per sonicmule) # ASUS K46CM # ASUS N76-VB-T4038H (per Tamshiii) # ASUS Zenbook Pro UX501VW (per Jingu) # ASUS G751JY (per Going Bald) # ASUS S300CA (per mugen441) # ASUS F556UA-AB32 (per Jdazzle44) # ASUS UX306UA (per MaraficeEye) # ASUS N550JV (per Xracer99) # ASUS X540LA (per arg274) # ASUS X540LJ (per palash) # ASUS X550VX (per vualeks) # ASUS UX330UA (per fluxo) # ASUS UX303UB (per CyanTech) # ASUS K550JK (per m3ftwz) # ASUS TP500LB (per Archangeliques) # ASUS X556UA (per ben9923) # ASUS UX410 (per minhquang211090) # ASUS N552VW (per nicolas2121) # ASUS Vivobook NV752 (per tmazzoni) # ASUS Strix FX502VM/GL502VM (per benspoonder) # ASUS X53E (per REvandenBerg) # ASUS UX430 (per starcentral) # ... # and many others into method label B1B2 remove_entry; into definitionblock code_regex . insert begin Method (B1B2, 2, NotSerialized) { Return (Or (Arg0, ShiftLeft (Arg1, 8))) }\n end; # not really for battery, but might come in handy to read fan speed(s) into device label EC0 code_regex TAH0,\s+16 replace_matched begin TH00,8,TH01,8 end; into device label EC0 code_regex TAH1,\s+16 replace_matched begin TH10,8,TH11,8 end; into method label TACH code_regex \(TAH0, replace_matched begin (B1B2(TH00,TH01), end; into method label TACH code_regex \(TAH1, replace_matched begin (B1B2(TH10,TH11), end; into method label GFAN code_regex \(\\_SB\.PCI0\.LPCB\.EC0\.TAH0, replace_matched begin (B1B2(\\_SB.PCI0.LPCB.EC0.TH00,\\_SB.PCI0.LPCB.EC0.TH01), end; # battery EC into device label EC0 code_regex B0SN,\s+16 replace_matched begin B0S0,8,B0S1,8 end; into device label EC0 code_regex B1SN,\s+16 replace_matched begin B1S0,8,B1S1,8 end; into method label BIFA code_regex \(B0SN, replace_matched begin (B1B2(B0S0,B0S1), end; into method label BIFA code_regex \(B1SN, replace_matched begin (B1B2(B1S0,B1S1), end; into device label EC0 code_regex DT2B,\s+16 replace_matched begin T2B0,8,T2B1,8 end; into method label SMBR code_regex \(DT2B, replace_matched begin (B1B2(T2B0,T2B1), end; into method label SMBW code_regex Store\s+\(([^,]*),\s+DT2B\) replace_matched begin Store(%1,T2B0) Store(ShiftRight(%1,8),T2B1) end; into device label EC0 insert begin Method (RDBA, 0, Serialized)\n {\n Name (TEMP, Buffer(0x20) { })\n Store (BA00, Index(TEMP, 0x00))\n Store (BA01, Index(TEMP, 0x01))\n Store (BA02, Index(TEMP, 0x02))\n Store (BA03, Index(TEMP, 0x03))\n Store (BA04, Index(TEMP, 0x04))\n Store (BA05, Index(TEMP, 0x05))\n Store (BA06, Index(TEMP, 0x06))\n Store (BA07, Index(TEMP, 0x07))\n Store (BA08, Index(TEMP, 0x08))\n Store (BA09, Index(TEMP, 0x09))\n Store (BA0A, Index(TEMP, 0x0A))\n Store (BA0B, Index(TEMP, 0x0B))\n Store (BA0C, Index(TEMP, 0x0C))\n Store (BA0D, Index(TEMP, 0x0D))\n Store (BA0E, Index(TEMP, 0x0E))\n Store (BA0F, Index(TEMP, 0x0F))\n Store (BA10, Index(TEMP, 0x10))\n Store (BA11, Index(TEMP, 0x11))\n Store (BA12, Index(TEMP, 0x12))\n Store (BA13, Index(TEMP, 0x13))\n Store (BA14, Index(TEMP, 0x14))\n Store (BA15, Index(TEMP, 0x15))\n Store (BA16, Index(TEMP, 0x16))\n Store (BA17, Index(TEMP, 0x17))\n Store (BA18, Index(TEMP, 0x18))\n Store (BA19, Index(TEMP, 0x19))\n Store (BA1A, Index(TEMP, 0x1A))\n Store (BA1B, Index(TEMP, 0x1B))\n Store (BA1C, Index(TEMP, 0x1C))\n Store (BA1D, Index(TEMP, 0x1D))\n Store (BA1E, Index(TEMP, 0x1E))\n Store (BA1F, Index(TEMP, 0x1F))\n Return (TEMP)\n }\n end; into device label EC0 insert begin Method (WRBA, 1, Serialized)\n {\n Name (TEMP, Buffer(0x20) { })\n Store (Arg0, TEMP)\n Store (DerefOf(Index(TEMP, 0x00)), BA00)\n Store (DerefOf(Index(TEMP, 0x01)), BA01)\n Store (DerefOf(Index(TEMP, 0x02)), BA02)\n Store (DerefOf(Index(TEMP, 0x03)), BA03)\n Store (DerefOf(Index(TEMP, 0x04)), BA04)\n Store (DerefOf(Index(TEMP, 0x05)), BA05)\n Store (DerefOf(Index(TEMP, 0x06)), BA06)\n Store (DerefOf(Index(TEMP, 0x07)), BA07)\n Store (DerefOf(Index(TEMP, 0x08)), BA08)\n Store (DerefOf(Index(TEMP, 0x09)), BA09)\n Store (DerefOf(Index(TEMP, 0x0A)), BA0A)\n Store (DerefOf(Index(TEMP, 0x0B)), BA0B)\n Store (DerefOf(Index(TEMP, 0x0C)), BA0C)\n Store (DerefOf(Index(TEMP, 0x0D)), BA0D)\n Store (DerefOf(Index(TEMP, 0x0E)), BA0E)\n Store (DerefOf(Index(TEMP, 0x0F)), BA0F)\n Store (DerefOf(Index(TEMP, 0x10)), BA10)\n Store (DerefOf(Index(TEMP, 0x11)), BA11)\n Store (DerefOf(Index(TEMP, 0x12)), BA12)\n Store (DerefOf(Index(TEMP, 0x13)), BA13)\n Store (DerefOf(Index(TEMP, 0x14)), BA14)\n Store (DerefOf(Index(TEMP, 0x15)), BA15)\n Store (DerefOf(Index(TEMP, 0x16)), BA16)\n Store (DerefOf(Index(TEMP, 0x17)), BA17)\n Store (DerefOf(Index(TEMP, 0x18)), BA18)\n Store (DerefOf(Index(TEMP, 0x19)), BA19)\n Store (DerefOf(Index(TEMP, 0x1A)), BA1A)\n Store (DerefOf(Index(TEMP, 0x1B)), BA1B)\n Store (DerefOf(Index(TEMP, 0x1C)), BA1C)\n Store (DerefOf(Index(TEMP, 0x1D)), BA1D)\n Store (DerefOf(Index(TEMP, 0x1E)), BA1E)\n Store (DerefOf(Index(TEMP, 0x1F)), BA1F)\n }\n end; into device label EC0 code_regex BDAT,\s+256 replace_matched begin //BDAT, 256,\n BA00,8,BA01,8,BA02,8,BA03,8,\n BA04,8,BA05,8,BA06,8,BA07,8,\n BA08,8,BA09,8,BA0A,8,BA0B,8,\n BA0C,8,BA0D,8,BA0E,8,BA0F,8,\n BA10,8,BA11,8,BA12,8,BA13,8,\n BA14,8,BA15,8,BA16,8,BA17,8,\n BA18,8,BA19,8,BA1A,8,BA1B,8,\n BA1C,8,BA1D,8,BA1E,8,BA1F,8\n end; into method label SMBR code_regex \(BDAT, replaceall_matched begin (RDBA(), end; into method label SMBR code_regex Store\s\((.*),\sBDAT\) replaceall_matched begin WRBA(%1) end; into method label SMBW code_regex Store\s\((.*),\sBDAT\) replaceall_matched begin WRBA(%1) end; into method label ECSB code_regex Store\s\((.*),\sBDAT\) replaceall_matched begin WRBA(%1) end; into method label ECSB code_regex \(BDAT, replaceall_matched begin (RDBA(), end; into device label EC0 insert begin Method (RDBB, 0, Serialized)\n {\n Name (TEMP, Buffer(0x20) { })\n Store (BB00, Index(TEMP, 0x00))\n Store (BB01, Index(TEMP, 0x01))\n Store (BB02, Index(TEMP, 0x02))\n Store (BB03, Index(TEMP, 0x03))\n Store (BB04, Index(TEMP, 0x04))\n Store (BB05, Index(TEMP, 0x05))\n Store (BB06, Index(TEMP, 0x06))\n Store (BB07, Index(TEMP, 0x07))\n Store (BB08, Index(TEMP, 0x08))\n Store (BB09, Index(TEMP, 0x09))\n Store (BB0A, Index(TEMP, 0x0A))\n Store (BB0B, Index(TEMP, 0x0B))\n Store (BB0C, Index(TEMP, 0x0C))\n Store (BB0D, Index(TEMP, 0x0D))\n Store (BB0E, Index(TEMP, 0x0E))\n Store (BB0F, Index(TEMP, 0x0F))\n Store (BB10, Index(TEMP, 0x10))\n Store (BB11, Index(TEMP, 0x11))\n Store (BB12, Index(TEMP, 0x12))\n Store (BB13, Index(TEMP, 0x13))\n Store (BB14, Index(TEMP, 0x14))\n Store (BB15, Index(TEMP, 0x15))\n Store (BB16, Index(TEMP, 0x16))\n Store (BB17, Index(TEMP, 0x17))\n Store (BB18, Index(TEMP, 0x18))\n Store (BB19, Index(TEMP, 0x19))\n Store (BB1A, Index(TEMP, 0x1A))\n Store (BB1B, Index(TEMP, 0x1B))\n Store (BB1C, Index(TEMP, 0x1C))\n Store (BB1D, Index(TEMP, 0x1D))\n Store (BB1E, Index(TEMP, 0x1E))\n Store (BB1F, Index(TEMP, 0x1F))\n Return (TEMP)\n }\n end; into device label EC0 insert begin Method (WRBB, 1, Serialized)\n {\n Name (TEMP, Buffer(0x20) { })\n Store (Arg0, TEMP)\n Store (DerefOf(Index(TEMP, 0x00)), BB00)\n Store (DerefOf(Index(TEMP, 0x01)), BB01)\n Store (DerefOf(Index(TEMP, 0x02)), BB02)\n Store (DerefOf(Index(TEMP, 0x03)), BB03)\n Store (DerefOf(Index(TEMP, 0x04)), BB04)\n Store (DerefOf(Index(TEMP, 0x05)), BB05)\n Store (DerefOf(Index(TEMP, 0x06)), BB06)\n Store (DerefOf(Index(TEMP, 0x07)), BB07)\n Store (DerefOf(Index(TEMP, 0x08)), BB08)\n Store (DerefOf(Index(TEMP, 0x09)), BB09)\n Store (DerefOf(Index(TEMP, 0x0A)), BB0A)\n Store (DerefOf(Index(TEMP, 0x0B)), BB0B)\n Store (DerefOf(Index(TEMP, 0x0C)), BB0C)\n Store (DerefOf(Index(TEMP, 0x0D)), BB0D)\n Store (DerefOf(Index(TEMP, 0x0E)), BB0E)\n Store (DerefOf(Index(TEMP, 0x0F)), BB0F)\n Store (DerefOf(Index(TEMP, 0x10)), BB10)\n Store (DerefOf(Index(TEMP, 0x11)), BB11)\n Store (DerefOf(Index(TEMP, 0x12)), BB12)\n Store (DerefOf(Index(TEMP, 0x13)), BB13)\n Store (DerefOf(Index(TEMP, 0x14)), BB14)\n Store (DerefOf(Index(TEMP, 0x15)), BB15)\n Store (DerefOf(Index(TEMP, 0x16)), BB16)\n Store (DerefOf(Index(TEMP, 0x17)), BB17)\n Store (DerefOf(Index(TEMP, 0x18)), BB18)\n Store (DerefOf(Index(TEMP, 0x19)), BB19)\n Store (DerefOf(Index(TEMP, 0x1A)), BB1A)\n Store (DerefOf(Index(TEMP, 0x1B)), BB1B)\n Store (DerefOf(Index(TEMP, 0x1C)), BB1C)\n Store (DerefOf(Index(TEMP, 0x1D)), BB1D)\n Store (DerefOf(Index(TEMP, 0x1E)), BB1E)\n Store (DerefOf(Index(TEMP, 0x1F)), BB1F)\n }\n end; into device label EC0 code_regex BDA2,\s+256 replace_matched begin //BDA2, 256,\n BB00,8,BB01,8,BB02,8,BB03,8,\n BB04,8,BB05,8,BB06,8,BB07,8,\n BB08,8,BB09,8,BB0A,8,BB0B,8,\n BB0C,8,BB0D,8,BB0E,8,BB0F,8,\n BB10,8,BB11,8,BB12,8,BB13,8,\n BB14,8,BB15,8,BB16,8,BB17,8,\n BB18,8,BB19,8,BB1A,8,BB1B,8,\n BB1C,8,BB1D,8,BB1E,8,BB1F,8\n end; into method label SMBR code_regex \(BDA2, replaceall_matched begin (RDBB(), end; into method label SMBR code_regex Store\s\((.*),\sBDA2\) replaceall_matched begin WRBB(%1) end; into method label SMBW code_regex Store\s\((.*),\sBDA2\) replaceall_matched begin WRBB(%1) end; into method label ECSB code_regex Store\s\((.*),\sBDA2\) replaceall_matched begin WRBB(%1) end; into method label ECSB code_regex \(BDA2, replaceall_matched begin (RDBB(), end; # additional work for _BIX method present in some ASUS laptops into device label EC0 code_regex B0C3,\s+16 replace_matched begin XC30,8,XC31,8 end; into device label EC0 code_regex B1C3,\s+16 replace_matched begin YC30,8,YC31,8 end; into_all method label _BIX code_regex \(\^\^LPCB\.EC0\.B0C3, replaceall_matched begin (B1B2(^^LPCB.EC0.XC30,^^LPCB.EC0.XC31), end; into_all method label _BIX code_regex \(\^\^LPCB\.EC0\.B1C3, replaceall_matched begin (B1B2(^^LPCB.EC0.YC30,^^LPCB.EC0.YC31), end; into_all method label _BIX code_regex \(B0C3, replaceall_matched begin (B1B2(XC30,XC31), end; # or could remove the _BIX method if it turns out not to work #into_all method label _BIX remove_entry; #fix logic error in some newer ASUS DSDTs (issue #23) into method label FBST code_regex If\s\(CHGS\s\(Zero\)\)[\s]+\{[\s]+Store\s\(0x02,\sLocal0\)[\s]+\}[\s]+Else[\s]+\{[\s]+Store\s\(One,\sLocal0\)[\s]+\} replaceall_matched begin If (CHGS (Zero))\n {\n Store (0x02, Local0)\n }\n Else\n {\n Store (Zero, Local0)\n } end;  
      USB 3.0 & Instant wake fix
      #Maintained by: RehabMan for: Laptop Patches #usb_prw_0x0d_xhc.txt # remove _PRW methods to prevent instant wake # delete any existing XHC1 device into device label XHC1 name_adr 0x00140000 remove_entry; # delete any existing USB2 device into device label USB2 name_adr 0x001D0000 remove_entry; # if _PRW objects are methods into method label _PRW parent_adr 0x001D0000 remove_entry; into method label _PRW parent_adr 0x001A0000 remove_entry; into method label _PRW parent_adr 0x00140000 remove_entry; into method label _PRW parent_adr 0x001B0000 remove_entry; # some other LAN cards use 0x00190000 into method label _PRW parent_adr 0x00190000 remove_entry; # if _PRW methods are stuffed into a separate scope into method label _PRW parent_label _SB.PCI0.EHC1 remove_entry; into method label _PRW parent_label _SB.PCI0.EHC2 remove_entry; into method label _PRW parent_label _SB.PCI0.XHC remove_entry; into method label _PRW parent_label \_SB.PCI0.EHC1 remove_entry; into method label _PRW parent_label \_SB.PCI0.EHC2 remove_entry; into method label _PRW parent_label \_SB.PCI0.XHC remove_entry; # if _PRW objects are names into device name_adr 0x001D0000 code_regex Name.*_PRW.*\n.*\n.*\n.*\n.*\}\) remove_matched; into device name_adr 0x001A0000 code_regex Name.*_PRW.*\n.*\n.*\n.*\n.*\}\) remove_matched; into device name_adr 0x00140000 code_regex Name.*_PRW.*\n.*\n.*\n.*\n.*\}\) remove_matched; into device name_adr 0x001B0000 code_regex Name.*_PRW.*\n.*\n.*\n.*\n.*\}\) remove_matched; into device name_adr 0x00190000 code_regex Name.*_PRW.*\n.*\n.*\n.*\n.*\}\) remove_matched; # some _PRW have three entries in the Package into device name_adr 0x001D0000 code_regex Name.*_PRW.*\n.*\n.*\n.*\n.*\n.*\}\) remove_matched; into device name_adr 0x001A0000 code_regex Name.*_PRW.*\n.*\n.*\n.*\n.*\n.*\}\) remove_matched; into device name_adr 0x00140000 code_regex Name.*_PRW.*\n.*\n.*\n.*\n.*\n.*\}\) remove_matched; into device name_adr 0x001B0000 code_regex Name.*_PRW.*\n.*\n.*\n.*\n.*\n.*\}\) remove_matched; into device name_adr 0x00190000 code_regex Name.*_PRW.*\n.*\n.*\n.*\n.*\n.*\}\) remove_matched; # seems to work better if _PRW is present, but returns 0 (original was 3) for sleep state into device name_adr 0x001D0000 insert begin Name(_PRW, Package() { 0x0D, 0 }) end; into device name_adr 0x001A0000 insert begin Name(_PRW, Package() { 0x0D, 0 }) end; into device name_adr 0x00140000 insert begin Name(_PRW, Package() { 0x0D, 0 }) end; into device name_adr 0x001B0000 insert begin Name(_PRW, Package() { 0x0D, 0 }) end; into device name_adr 0x00190000 insert begin Name(_PRW, Package() { 0x0D, 0 }) end; # USB property injection for 7-series boards (originally HM76) # Insert Apple USB properties into EHC1 into method label _DSM parent_adr 0x001D0000 remove_entry; into device name_adr 0x001D0000 insert begin Method (_DSM, 4, NotSerialized)\n {\n If (LEqual (Arg2, Zero)) { Return (Buffer() { 0x03 } ) }\n Return (Package()\n {\n "subsystem-id", Buffer() { 0x70, 0x72, 0x00, 0x00 },\n "subsystem-vendor-id", Buffer() { 0x86, 0x80, 0x00, 0x00 },\n "AAPL,current-available", 2100,\n "AAPL,current-extra", 2200,\n "AAPL,current-extra-in-sleep", 1600,\n "AAPL,device-internal", 0x02,\n "AAPL,max-port-current-in-sleep", 2100,\n })\n }\n end; # Insert Apple USB properties into EHC2 into method label _DSM parent_adr 0x001A0000 remove_entry; into device name_adr 0x001A0000 insert begin Method (_DSM, 4, NotSerialized)\n {\n If (LEqual (Arg2, Zero)) { Return (Buffer() { 0x03 } ) }\n Return (Package()\n {\n "subsystem-id", Buffer() { 0x70, 0x72, 0x00, 0x00 },\n "subsystem-vendor-id", Buffer() { 0x86, 0x80, 0x00, 0x00 },\n "AAPL,current-available", 2100,\n "AAPL,current-extra", 2200,\n "AAPL,current-extra-in-sleep", 1600,\n "AAPL,device-internal", 0x02,\n "AAPL,max-port-current-in-sleep", 2100,\n })\n }\n end; # Insert Apple USB properties into USB 3.0 XHC into method label _DSM parent_adr 0x00140000 remove_entry; into device name_adr 0x00140000 insert begin Method (_DSM, 4, NotSerialized)\n {\n If (LEqual (Arg2, Zero)) { Return (Buffer() { 0x03 } ) }\n Return (Package()\n {\n "subsystem-id", Buffer() { 0x70, 0x72, 0x00, 0x00 },\n "subsystem-vendor-id", Buffer() { 0x86, 0x80, 0x00, 0x00 },\n "AAPL,current-available", 2100,\n "AAPL,current-extra", 2200,\n "AAPL,current-extra-in-sleep", 1600,\n "AAPL,device-internal", 0x02,\n "AAPL,max-port-current-in-sleep", 2100,\n })\n }\n end; # special cases... (not in u430 DSDT) #into scope label _SB.PCI0.XHC.RHUB.HS05 set_label begin _SB.PCI0.XHC1.RHUB.HS05 end; - Finally, click in "Compile" to check for errors.
      - If you get the error Object does not exists (\_SB.PCI0.XHC1) remove the 1 and try compile again.
      - Close and reboot.
       
      Last thing
       
      Run this command in Terminal to disable hibernation (doesn't work in macOS):
      sudo pmset -a hibernatemode 0  
       
      It's done!
       
       
      System Updates
       
      10.15.2
       
      Before install, update the following kexts:
      - Lilu.kext. I used version 1.4.0.
      - WhateverGreen.kext. I used version 1.3.5.
      - AppleALC.kext. I used version 1.4.4.
      - VoodooPS2Controller.kext. I used version 2.1.0.
      (all download links above)
       
      Download the latest CLOVERX64.efi.zip build. I used version 5100.
      Mount EFI partition and unzip to:
      - /Volumes/EFI/EFI/CLOVER/CLOVERX64.efi
      - /Volumes/EFI/EFI/BOOT/BOOTX64.efi (rename the copy of CLOVERX64.efi to BOOTX64.efi
       
      Install update. Will reboot at least four time.
       
       
       

      And last but not least

      I would like to thank the following community members, by making these dream possible:
      @crushers, @snatch, @apianti, @blackosx, @blusseau, @dmazar, @slice2009, @autumnrain, @phpdev32, @EMlyDinEsH, @RehabMan, @Scellow, @mitch_de, @Shailua, @Andy Vandijck, @maxfierke, @ArturXXX, @LexHimself, @brumas, @"Sniki", @Mieze, @headkaze and all others members involved directly or indirectly.
       
       
      Attachments
       
      config.plist
      SSDTs v3.zip
      USBPorts.kext.zip
      VoodooPS2Controller.kext.zip
      Filevault 2 additional drivers.zip
      AtherosE2200Ethernet.kext v2.zip
       
×