Jump to content
ricola

[pre-release] macOS Sierra 10.12.4

235 posts in this topic

Recommended Posts

You are first reporter now!!!! Thank you so much.

 

KernelToPatch Enable or disable not working right? Or work like r3974? I dont have good english.

Okay reversed enable/disable in KernelPatch. I will check

 

If have problem about enable/disable in KernelToPatch, i will give you file to fix this issue.

 

나의 LG-F410S 의 Tapatalk에서 보냄

I'm using Clover r3994 and Sierra 12.4

Since I made the update for Clover r3994 and for Sierra 12.4, I was without sound and without XCPM.

I did some tests and discovered the following:

With xcpm patchs enabled in Plist - Cpu blocks at maximum frequency. (No XCPM)

With xcpm patchs disabled in Plist - Everything went back to normal, XCPM working, Speedsteps working, Freq.Vectors loaded, everything loaded.

With your Fix, the sound worked fine again, but the xcpm remains the same. I only have speedsteps if I disable all the xcpm patchs in Clover.

Now I'm going to test your r3995 fix and then report as it ran :yes: 

Tanks

Share this post


Link to post
Share on other sites
Advertisement

Updating to 10.12.4 Public Beta 1 I have a deep trouble.

My screen is flickering. 

If I attach two monitors, one to Intel embedded and second to Radeon then Radeon flickering.

New system has two new kexts AMDLegacy*** and they are attached to my Radeon.

If I move them to trash them no signal.

This is deadened for my AMD Radeon HD6670. It is no more supported since 10.12.4.

As I temporary solution I work in 10.12.2 now.

Nothing new.

I currently have to to content myself with Intel HD Graphics 4600, removing AMD, injecting the id and with intel true in Clover .plist.

Share this post


Link to post
Share on other sites

Hi Sherlock,

I just tested the r3994 Fix and the r3995 Fix and the behavior was the same in both.

With both, the sound (AppleHDA) worked perfect again, but about XCPM, it only works if I disable all the patches in plist.

If I activate them, XCPM stops working. Sounds like the enable/disable are reversed in Clover r3994.

If you want, check out my latest EFI and confirm on my last plist.
BTW, according to my hardware, if you think I should change anything at EFI, please let me know! :) 

Once again, thank you.

EFI.rar

Share this post


Link to post
Share on other sites

Hi @Fergarth.

I just noticed that you set all patches' MatchOS to 10.12, but I was not sure what they mean.

Because if you want to patch something for 10.12.0 and then the MatchOS should be '10.12.0' instead of '10.12'.

But you said that AppleHDA is working and patches for kernel not, this meant that '10.12' just made no difference. (If '10.12' means '10.12.0' then your patches for AppleHDA will not be allowed.)

So I'd like to know that the patches are allowed actually? I checked your /EFI/CLOVER/misc/preboot.log but there must be something missing. May share a new one via "Clover Configurator ==> TOOLS ==> Boot.log ==> Save boot.log to desktop"?

BTW. It seems that your XCPM patches are wrong and therefore this can be a reason for why you said that XCPM not working. You just patched _cpuid_set_info() but actually this made no difference on Haswell-E. It was just required by Broadwell-E cuz we missed some data for it in kernel. So. You have to patch _xcpm_bootstrap() for Haswell-E. But I saw you had disabled it. (# XCPM Bootstrap Sierra © Pike R. Alpha) Also. Some patches for early reboot, performance, were also disabled now. I didn't know which patch for early reboot is necessary to you and thus I enabled all of them. Anyway. Less is more.

I patched your config.plist and you might check whether XCPM would be working. FYI.

No... You mean that KernelToPatch is reversed/broken... Right? Sorry for my brain got messed. In this case, give me some time to check what's wrong...

Edited by PMheart

Share this post


Link to post
Share on other sites

Hi Sherlock,

I just tested the r3994 Fix and the r3995 Fix and the behavior was the same in both.

With both, the sound (AppleHDA) worked perfect again, but about XCPM, it only works if I disable all the patches in plist.

If I activate them, XCPM stops working. Sounds like the enable/disable are reversed in Clover r3994.

If you want, check out my latest EFI and confirm on my last plist.

BTW, according to my hardware, if you think I should change anything at EFI, please let me know! :)

Once again, thank you.

 

 

i want to test 2 times.

 

first

for r3974.zip

download. and install r3974 official pkg, and replace config.plist from "for r3974.zip". before reboot, you can see what i did(i did enable your all kernel patch). then reboot.

r3974 link

https://sourceforge.net/projects/cloverefiboot/files/Installer/

 

two

r3995 newfix.zip

download. install r3994 official pkg, and replace efi files. before reboot, you use your pure config.plist(you used it before) with enable kernel patch.

 

 

report please. also i want to know when you install 10.12.3 official with r3974,  is enable kernel patch no problem?

 

 

thank you for report and effort.

Share this post


Link to post
Share on other sites

Hi @Fergarth.

I just noticed that you set all patches' MatchOS to 10.12, but I was not sure what they mean.

Because if you want to patch something for 10.12.0 and then the MatchOS should be '10.12.0' instead of '10.12'.

But you said that AppleHDA is working and patches for kernel not, this meant that '10.12' just made no difference. (If '10.12' means '10.12.0' then your patches for AppleHDA will not be allowed.)

So I'd like to know that the patches are allowed actually? I checked your /EFI/CLOVER/misc/preboot.log but there must be something missing. May share a new one via "Clover Configurator ==> TOOLS ==> Boot.log ==> Save boot.log to desktop"?

BTW. It seems that your XCPM patches are wrong and therefore this can be a reason for why you said that XCPM not working. You just patched _cpuid_set_info() but actually this made no difference on Haswell-E. It was just required by Broadwell-E cuz we missed some data for it in kernel. So. You have to patch _xcpm_bootstrap() for Haswell-E. But I saw you had disabled it. (# XCPM Bootstrap Sierra © Pike R. Alpha) Also. Some patches for early reboot, performance, were also disabled now. I didn't know which patch for early reboot is necessary to you and thus I enabled all of them. Anyway. Less is more.

I patched your config.plist and you might check whether XCPM would be working. FYI.

No... You mean that KernelToPatch is reversed/broken... Right? Sorry for my brain got messed. In this case, give me some time to check what's wrong...

attachicon.gifconfig.plist.zip

Yes, I can even change the MatchOS, but from what I've seen, it's just a question of cosmetics. As it is or with nothing, it always worked well lol. I only started to have stress since I installed Sierra 12.4 and last Clover r3994 that appears to have a bug, for the reason I mentioned.

I tried it with Clover r3974, but it did not finish the boot in 12.4 and that's why I installed r3994.

As for the Patchs, they were always the ones I used in 10.12.1, 12.2, 12.3 (betas included) and I never had problems, reboots, freezes... etc

But if you think I should change anything on my EFI, feel free to tell me. I appreciate it :) 

Share this post


Link to post
Share on other sites

Yes, I can even change the MatchOS, but from what I've seen, it's just a question of cosmetics. As it is or with nothing, it always worked well lol. I only started to have stress since I installed Sierra 12.4 and last Clover r3994 that appears to have a bug, for the reason I mentioned.

I tried it with Clover r3374, but it did not finish the boot in 12.4 and that's why I installed r3994.

As for the Patchs, they were always the ones I used in 10.12.1, 12.2, 12.3 (betas included) and I never had problems, reboots, freezes... etc

But if you think I should change anything on my EFI, feel free to tell me. I appreciate it :)

This means if Clover got an illegal MatchOS then it may set MatchOS to "" (Null string.) and thus the patch will be allowed.

IMHO. Before Clover gets stable, just revert back to 3974 and add a KernelToPatch that I mentioned in PM. And 10.12.4 should work fine with Clover r3974 w/ KernelToPatch for InjectKext.

Share this post


Link to post
Share on other sites

i want to test 2 times.

 

first

attachicon.giffor r3974.zip

download. and install r3974 official pkg, and replace config.plist from "for r3974.zip". before reboot, you can see what i did(i did enable your all kernel patch). then reboot.

r3974 link

https://sourceforge.net/projects/cloverefiboot/files/Installer/

 

two

attachicon.gifr3995 newfix.zip

download. install r3994 official pkg, and replace efi files. before reboot, you use your pure config.plist(you used it before) with enable kernel patch.

 

 

report please. also i want to know when you install 10.12.3 official with r3974,  is enable kernel patch no problem?

 

 

thank you for report and effort.

 

Thank you for your attention Sherlocks,

I'm not really sure, but if I'm not mistaken, r3974 already had it with 12.3 betas until 12.3 Final. One thing I'm sure, EFI / Plist Patchs has always been the same, but as soon as new versions of Clover or OS come out I do the updates and in fact, it has always gone well. It just went bad now with the last Clover r3994, for the reasons I said.

I have not had a chance yet, but as soon as I can, I'll try out these new FIX attached and then report it. :) 

Share this post


Link to post
Share on other sites

Thank you for your attention Sherlocks,

I'm not really sure, but if I'm not mistaken, r3974 already had it with 12.3 betas until 12.3 Final. One thing I'm sure, EFI / Plist Patchs has always been the same, but as soon as new versions of Clover or OS come out I do the updates and in fact, it has always gone well. It just went bad now with the last Clover r3994, for the reasons I said.

I have not had a chance yet, but as soon as I can, I'll try out these new FIX attached and then report it. :)

 

confirmed your report content before by myself in my laptop.

right. disable and enable become reverse. i reported it to clover team. 

 

until clover update, we have to wait.

 

thank you. have a good day

Share this post


Link to post
Share on other sites

Hi PMheart, Hi Sherlocks, (by alphabetical order) :P 

Ok, I already installed Clover r3998 on OS 12.4 and the Enable/Disable bug has been fixed. Everything went back to normal except the sound. With the same plist that always worked well, the sound stopped working. If i use the (r3994 Fix) suggested by Sherlocks, the sound works, but XCPM stops working, (unless I disable the patches as in r3994).
At this point everything works fine except the ALC1150 sound.
For sound, I use the patchs that are in the zip attachment and have been added by audio_cloverALC-120.command.zip, which always worked fine.
About the patchs for XCPM, given your knowledge, I would like to have your opinion!
If you can see my attachment and tell me which of the two plist suits my system better. One has 4 patches and the other has 7 patches, but in both XCPM works fine.
Thank you for your attention, for your knowledge, for everything... :) 

Zip.rar

Share this post


Link to post
Share on other sites

Hi PMheart, Hi Sherlocks, (by alphabetical order) :P

Ok, I already installed Clover r3998 on OS 12.4 and the Enable/Disable bug has been fixed. Everything went back to normal except the sound. With the same plist that always worked well, the sound stopped working. If i use the (r3994 Fix) suggested by Sherlocks, the sound works, but XCPM stops working, (unless I disable the patches as in r3994).

At this point everything works fine except the ALC1150 sound.

For sound, I use the patchs that are in the zip attachment and have been added by audio_cloverALC-120.command.zip, which always worked fine.

About the patchs for XCPM, given your knowledge, I would like to have your opinion!

If you can see my attachment and tell me which of the two plist suits my system better. One has 4 patches and the other has 7 patches, but in both XCPM works fine.

Thank you for your attention, for your knowledge, for everything... :)

Okay. I think you should acquaint how the patches work. I shall tell you how they work based on the comment of each patch.

Since all the patches are included in config2.plist and I won't tell anything about config1.plist, is that okay?  ;)

1. "XCPM Bootstrap Sierra © Pike R. Alpha". This is necessary. It will patch CPUID definition under _xcpm_bootstrap() and thus XCPM will be enabled on your Haswell-E.

2. "XCPM SMT Scope MSRS © Pike R. Alpha" This will prevent SMT Scope MSRs from calling. You may need this to fix early reboot issue. But typically. We don't need it. Note: You should do some experiments to know whether you need it.

3. "XCPM Idle Replace All Fix © Pike R. Alpha" This will make a difference if your 0xe2 register get locked. If your 0xe2 is okay. Just get rid of it. Else you will get an early reboot. Also. Do some experiments.

4. "XCPM PKG Scope MSRS © Pike R. Alpha" This will prevent PKG Scope MSRs from calling. Typically this is necessary. But if you can even remove this and then... Just remove it!  :P

5. "XCPM Performance Fix 1 (Fix CPU Max) © Okrasit" If you have any performance issues, just enable this one. IMHO. You ought to take a mess on here after all XCPM is okay. (So. Don't take a look at here until XCPM works.)

6. "XCPM Core Scope MSRS © Pike R. Alpha" is similar to "2. XCPM SMT Scope MSRS © Pike R. Alpha". Do some experiments to decide whether you need it.

7. "XCPM SMT Scope MSRS © Pike R. Alpha". Just the same as 2 & 6.  ^_^

 

IMHO. I don't own your case and thus I don't know details. But nevertheless. I think 1 & 3 & 4 & 5 are enough. Enable other ones if you encounter further issues...

Share this post


Link to post
Share on other sites

Also lost brightness after updating my Ivy Bridge/HD4000 Latitude E6230 to 10.12.4.b1. The brightness bar is there (thanks to IntelBacklight kext) but ineffective.

 

On rebuilding the cache, I've noticed what seems to be the culprits:

kxld[com.apple.driver.AppleMCCSControl]: The following symbols are unresolved for this kext:
kxld[com.apple.driver.AppleMCCSControl]: _gIODisplayBrightnessProbeKey
kxld[com.apple.driver.AppleMCCSControl]: _gIODisplayLinearBrightnessProbeKey
Link failed (error code 5).
Prelink failed for com.apple.driver.AppleMCCSControl; omitting from prelinked kernel.
kxld[com.apple.driver.AppleMuxControl]: The following symbols are unresolved for this kext:
kxld[com.apple.driver.AppleMuxControl]: _gIODisplayBrightnessProbeKey
kxld[com.apple.driver.AppleMuxControl]: _gIODisplayLinearBrightnessProbeKey
Link failed (error code 5).
Prelink failed for com.apple.driver.AppleMuxControl; omitting from prelinked kernel.
kxld[com.apple.driver.AppleBacklight]: The following symbols are unresolved for this kext:
kxld[com.apple.driver.AppleBacklight]: _gIODisplayBrightnessProbeKey
kxld[com.apple.driver.AppleBacklight]: _gIODisplayLinearBrightnessProbeKey
Link failed (error code 5).
Prelink failed for com.apple.driver.AppleBacklight; omitting from prelinked kernel.

Share this post


Link to post
Share on other sites
Hi PMheart, hi Sherlocks, hi RehabMan, hi others coders,

 

no way to be able to use yet adequately amd hd 5000 series and to avoid the flickering colors on the screen?

 

Help or expert advice would be very welcome.

Thanks.

Share this post


Link to post
Share on other sites

Okay. I think you should acquaint how the patches work. I shall tell you how they work based on the comment of each patch.

Since all the patches are included in config2.plist and I won't tell anything about config1.plist, is that okay?  ;)

1. "XCPM Bootstrap Sierra © Pike R. Alpha". This is necessary. It will patch CPUID definition under _xcpm_bootstrap() and thus XCPM will be enabled on your Haswell-E.

2. "XCPM SMT Scope MSRS © Pike R. Alpha" This will prevent SMT Scope MSRs from calling. You may need this to fix early reboot issue. But typically. We don't need it. Note: You should do some experiments to know whether you need it.

3. "XCPM Idle Replace All Fix © Pike R. Alpha" This will make a difference if your 0xe2 register get locked. If your 0xe2 is okay. Just get rid of it. Else you will get an early reboot. Also. Do some experiments.

4. "XCPM PKG Scope MSRS © Pike R. Alpha" This will prevent PKG Scope MSRs from calling. Typically this is necessary. But if you can even remove this and then... Just remove it!  :P

5. "XCPM Performance Fix 1 (Fix CPU Max) © Okrasit" If you have any performance issues, just enable this one. IMHO. You ought to take a mess on here after all XCPM is okay. (So. Don't take a look at here until XCPM works.)

6. "XCPM Core Scope MSRS © Pike R. Alpha" is similar to "2. XCPM SMT Scope MSRS © Pike R. Alpha". Do some experiments to decide whether you need it.

7. "XCPM SMT Scope MSRS © Pike R. Alpha". Just the same as 2 & 6.  ^_^

 

IMHO. I don't own your case and thus I don't know details. But nevertheless. I think 1 & 3 & 4 & 5 are enough. Enable other ones if you encounter further issues...

Hi friend,

When I asked, I was just curious to hear your opinion. But everything is fine, whether with 7 patches or 4, the system works perfect and stable as I want. Actually, I've mostly used only 4 and it's always been okay.

Thank you very much for your clarification :) 

Share this post


Link to post
Share on other sites

this thread about brightness working or not is getting very long haha anyway beta 1 was nice but how about beta 2 this week and my hack has been flawless with ozmosis 

Share this post


Link to post
Share on other sites

Ok, the cache rebuilding errors went away after I replaced my patched IOGraphicsFamily of 10.12.3 origin by 10.12.4.b1's patched version. I'm using Enoch so no on-the-fly patching like with Clover and I place up-versioned patched kexts in /L/E.

 

And the brightness issue was due to a simple error in DSDT's PNLF device (UID set to 0x0E instead of 0x0A)...  :blush:

 

All Ok now.

Share this post


Link to post
Share on other sites

Ok, the cache rebuilding errors went away after I replaced my patched IOGraphicsFamily of 10.12.3 origin by 10.12.4.b1's patched version. I'm using Enoch so no on-the-fly patching like with Clover and I place up-versioned patched kexts in /L/E.

 

And the brightness issue was due to a simple error in DSDT's PNLF device (UID set to 0x0E instead of 0x0A)...  :blush:

 

All Ok now.

You have brightness adjustment using Intelbacklight.kext?

Share this post


Link to post
Share on other sites

Following PNLF _UID value change, full brightness adjustment is available natively. I no longer require the IntelBacklight kext which, indeed, does not seem to work under 10.12.4.b1 (it worked Ok up to 10.12.3).

 

NB: the PNLF device of the DSDT includes the brightness definition code, i.e. the various _BCM, _BQC and _BCL methods.

Share this post


Link to post
Share on other sites

Hi friend,

When I asked, I was just curious to hear your opinion. But everything is fine, whether with 7 patches or 4, the system works perfect and stable as I want. Actually, I've mostly used only 4 and it's always been okay.

Thank you very much for your clarification :)

Oops. First of all sorry for delaying replying...

I think you can use even less than 4 patches, let's talk about the details:

"XCPM Bootstrap Sierra © Pike R. Alpha" is necessary and you have to keep it.

The rest 3 patches, which may be deleted, you may need to do some experiments to delete some of them, IMHO, "XCPM PKG Scope MSRS © Pike R. Alpha" could be not useful and thus you may disable/delete it. And the 2 other patches... Just do some experiments...

 

Hi PMheart, hi Sherlocks, hi RehabMan, hi others coders,
 
no way to be able to use yet adequately amd hd 5000 series and to avoid the flickering colors on the screen?
 
Help or expert advice would be very welcome.
Thanks.

 

Sorry. I don't have any AMD device and thus I must have no idea...

Share this post


Link to post
Share on other sites
Guest
This topic is now closed to further replies.

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By fantomas
      macOS Catalina 10.15.5
       
      macOS Catalina 10.15.5 introduces battery health management in the Energy Saver settings for notebooks, a new option to disable automatic prominence in Group FaceTime calls, and controls to fine-tune the built-in calibration of your Pro Display XDR. The update also improves the stability, reliability, and security of your Mac. 
       
      Battery Health Management
      Battery health management to help maximize battery lifespan for Mac notebooks Energy Saver preference pane now displays battery condition and recommends if the battery needs to be serviced Option to disable battery health management For more information, please visit https://support.apple.com/kb/HT211094
       
      FaceTime Prominence Preference 
      New option to control automatic prominence on Group FaceTime calls, so video tiles do not change size when a participant speaks  
      Calibration Fine-Tuning for Pro Display XDR
      Controls to fine-tune the built-in calibration of your Pro Display XDR by adjusting the white point and luminance for a precise match to your own display-calibration target  
      This update also includes bug fixes and other improvements:
      Fixes an issue that may prevent Reminders from sending notifications for recurring reminders Addresses an issue that may prevent password entry on the login screen Fixes an issue where System Preferences would continue to show a notification badge even after installing an update Resolves an issue where the built-in camera may not be detected when trying to use it after using a video conferencing app Addresses an issue for Mac computers with the Apple T2 Security Chip where internal speakers may not appear as a sound output device in Sound preferences Fixes a stability issue with uploading and downloading media files from iCloud Photo Library while your Mac is asleep Resolves a stability issue when transferring large amounts of data to RAID volumes Fixes an issue where the Reduced Motion Accessibility preference did not reduce the speed of animations in a Group FaceTime call  
      Enterprise content:
      Improves performance on certain Mac models when enabling hardware acceleration in GPU-intensive apps such as those used for video conferencing Addresses an issue where Microsoft Exchange accounts were unable to sign in during account setup when using Conditional Access Apple Push Notification Service traffic now uses a web proxy when specified in a PAC file via the Proxies payload Resolves an issue that prevented some displays connected to MacBook Pro (16-inch, 2019) from waking from sleep when the Mac wakes Major new releases of macOS are no longer hidden when using the softwareupdate(8) command with the  --ignore flag This change also affects macOS Mojave and macOS High Sierra after installing Security Update 2020-003.
       
      macOS Catalina 10.15.5 (19F96)
       
      Update
      Combo
       
      View full article
       
    • By fantomas
      macOS Catalina 10.15.5
      macOS Catalina 10.15.5 introduces battery health management in the Energy Saver settings for notebooks, a new option to disable automatic prominence in Group FaceTime calls, and controls to fine-tune the built-in calibration of your Pro Display XDR. The update also improves the stability, reliability, and security of your Mac. 
      Battery Health Management
      Battery health management to help maximize battery lifespan for Mac notebooks Energy Saver preference pane now displays battery condition and recommends if the battery needs to be serviced Option to disable battery health management For more information, please visit https://support.apple.com/kb/HT211094
      FaceTime Prominence Preference 
      New option to control automatic prominence on Group FaceTime calls, so video tiles do not change size when a participant speaks Calibration Fine-Tuning for Pro Display XDR
      Controls to fine-tune the built-in calibration of your Pro Display XDR by adjusting the white point and luminance for a precise match to your own display-calibration target This update also includes bug fixes and other improvements:
      Fixes an issue that may prevent Reminders from sending notifications for recurring reminders Addresses an issue that may prevent password entry on the login screen Fixes an issue where System Preferences would continue to show a notification badge even after installing an update Resolves an issue where the built-in camera may not be detected when trying to use it after using a video conferencing app Addresses an issue for Mac computers with the Apple T2 Security Chip where internal speakers may not appear as a sound output device in Sound preferences Fixes a stability issue with uploading and downloading media files from iCloud Photo Library while your Mac is asleep Resolves a stability issue when transferring large amounts of data to RAID volumes Fixes an issue where the Reduced Motion Accessibility preference did not reduce the speed of animations in a Group FaceTime call Enterprise content:
      Improves performance on certain Mac models when enabling hardware acceleration in GPU-intensive apps such as those used for video conferencing Addresses an issue where Microsoft Exchange accounts were unable to sign in during account setup when using Conditional Access Apple Push Notification Service traffic now uses a web proxy when specified in a PAC file via the Proxies payload Resolves an issue that prevented some displays connected to MacBook Pro (16-inch, 2019) from waking from sleep when the Mac wakes Major new releases of macOS are no longer hidden when using the softwareupdate(8) command with the  --ignore flag This change also affects macOS Mojave and macOS High Sierra after installing Security Update 2020-003.
       
      macOS Catalina 10.15.5 (19F96)
       
      Update
      Combo
    • By fantomas
      Version finale... macOS Catalina 10.15.5 (19F96)
    • By mavifree
      Sir 
      I am new in this, i try to make my hp laptop in hackintosh but i facing some error in clover boot manager while installing but unable to understand it. I really try hard but not able to get there, something i noticed that i facing same kind of error every time. I just watched youtube and visitied so forum like tonymac86, InsanelyMac, Noobsplanate and so on but nothing solved. So Please Please I Request All of You If you can help me to resolve my problem.
      Here Is my Laptop Specs:
      --------------------------------------------------------------------
      Laptop : HP cs2082tx
      Mobo : HP84C1
      Southbridge : Coffee Lake-U/Y PCH
      CPU : Intel Core i5 8265U @ 1.60GHz Kaby Lake- U/Y
      Ram : 8 Gb
      HDD : 256GB SSD & 1TB HDD
      Graphics : Intel UHD Graphic 620 with nvidia MX250
      ----------------------------------------------------------------------
       
      I even don't is my laptop is compatible or not, and don't have MacBook or Mac Desktop so if you can provide important driver and other stuff for installation. I really be very thankful to you.
      Please Reply me if any other information about my laptop hardware i will attached it i only have this info right now. 
       
      and i here attached my screenshot while installation error in clover.
      Sorry for my English.
       
      Please Help Me 
       



    • By MaLd0n
      -Donations with PayPal
      https://tinyurl.com/r2bvzm7
       
      -Donations with Bitcoin
      33HeGCuCSh4tUBqdYkQqKpSDa1E7WeAJQ3
       
      -Donations with PicPay 
      @danielnmaldonado
       
      -Donation with Mercado Livre 
      https://tinyurl.com/y9evkj5u
       
       
      --Original Topic--
      https://www.olarila.com/topic/6874-olarila-hackbook-lenovo-ideapad-s145-mojave-catalina-full-dsdt-patches/
       

       
      -Perfect HackBook, HDMI Audio/Video, Bluetooth, AirPlay, Sleep, Lid Sleep, Auto Sleep, Audio, etc!
      -Wifi card has been replaced with Dell DW1560!
      -I'm using a S145-15IWL Model with Intel Core i5 8265u / Intel UHD Graphics 620
      -Update bios/uefi to last version
       
      --Installation--
      https://www.olarila.com/topic/5794-guide-install-macos-with-olarila-image-step-by-step-install-and-post-install-windows-or-mac/
       
      --Clover Folder--
      Just paste EFI folder inside EFI partition
      https://tinyurl.com/rkqmpd9
       
      Bluetooth Broadcom
      Bluetooth Broadcom.zip
       
      CPUFriend for i5-8265U
      CPUFriend i5-8265U.zip
       
      --Full DSDT Patches--
      -My DSDT
      DSDT Lenovo IdeaPad S145.zip
       
      This DSDT work on S145-14IWL, S145-15IWL, V14-IWL, V15-IWL models
      -Patches
      -FIX ERRORS AND WARNINGS -REMOVE UNUSED SCOPES / DEVICES -HIGH PRECISION EVENT TIMER -SATA SERIE 11 ID -DMAC -REMOVE LINES, PROBLEMATIC and UNUSED -SLPB -DARWIN / WINDOWS 2015 -XHCI -PLUGIN TYPE -HDAS to HDEF -HDEF -REAL TIME CLOCK -ARTC -IRQs -SBUS -BUS1 -MCHC -ALS0 -SHUTDOWN -FWHD -USBX -PMCR -PPMC -XSPI -GMM -IMEI -EC -PRWs -_DSMs -PNLF -BRIGHTNESS KEYS -I2C -NATIVE USB -ARPT -GFX0 -DTGP -kUSBCompanionIndex -io-device-location -FULL RENAMED DEVICES   --IGPU Patch--
      Video solution with HDMI Audio and Video
      <key>PciRoot(0x0)/Pci(0x2,0x0)</key> <dict> <key>AAPL,GfxYTile</key> <data> AQAAAA== </data> <key>AAPL,ig-platform-id</key> <data> CQClPg== </data> <key>device-id</key> <data> pT4AAA== </data> <key>enable-hdmi20</key> <data> AQAAAA== </data> <key>framebuffer-con0-alldata</key> <data> AAAIAAIAAACYAAAA </data> <key>framebuffer-con0-enable</key> <integer>1</integer> <key>framebuffer-con1-alldata</key> <data> AQEJAAAIAADHAQAA </data> <key>framebuffer-con1-enable</key> <integer>1</integer> <key>framebuffer-con2-alldata</key> <data> AgYKAAAEAADHAQAA </data> <key>framebuffer-con2-enable</key> <integer>1</integer> <key>framebuffer-fbmem</key> <data> AACQAA== </data> <key>framebuffer-patch-enable</key> <data> AQAAAA== </data> <key>framebuffer-stolenmem</key> <data> AAAwAQ== </data> <key>framebuffer-unifiedmem</key> <data> AAAAgA== </data> <key>hda-gfx</key> <string>onboard-1</string> <key>model</key> <string>Intel Corporation, Iris Plus Graphics 655</string> </dict>   --Native USB Fix for Notebooks - No Injector/Kext Required--
      https://www.olarila.com/topic/6878-guide-native-usb-fix-for-notebooks-no-injectorkext-required/
      https://www.olarila.com/topic/6181-guide-native-usb-fix-for-desktops-no-injectorkext-required-skylake/
       
       
      -ScreenShots

































      -Links
       
       
      Clover https://github.com/CloverHackyColor/CloverBootloader
      AirportBrcmFixup.kext https://github.com/acidanthera/AirportBrcmFixup
      AppleALC.kext https://github.com/acidanthera/AppleALC
      Brcm Bluetooth https://github.com/acidanthera/BrcmPatchRAM
      Lilu.kext https://github.com/acidanthera/Lilu
      SystemProfilerMemoryFixup.kext https://github.com/Goldfish64/SystemProfilerMemoryFixup
      VirtualSMC.kext https://github.com/acidanthera/VirtualSMC
      VoodooI2C.kext https://github.com/alexandred/VoodooI2C
      VoodooPS2Controller.kext https://github.com/acidanthera/VoodooPS2
      WhateverGreen.kext https://github.com/acidanthera/WhateverGreen
      MaciASL - https://github.com/acidanthera/MaciASL
      acpica - https://github.com/acpica/acpica
      AptioMemoryFix.efi https://github.com/acidanthera/AptioFixPkg
      ApfsDriverLoader.efi https://github.com/acidanthera/AppleSupportPkg
      HFSPlus.efi https://github.com/JrCs/CloverGrowerPro/blob/master/Files/HFSPlus/X64/HFSPlus.efi?raw=true
      Hackintool https://github.com/headkaze/Hackintool
       
      -Credits and thanks to the old and new people in the community who developed patches, kexts and bootloaders!
       
      Slice, Kabyl, usr-sse2, jadran, Blackosx, dmazar, STLVNUB, pcj, apianti, JrCs, pene, FrodoKenny, skoczy, ycr.ru, Oscar09, xsmile, SoThOr, RehabMan, Download-Fritz, Zenit432, cecekpawon, Intel, Apple, Oracle, Chameleon Team, crazybirdy, Mieze, Mirone, Oldnapalm, netkas, Elconiglio, artut-pt, ErmaC, Pavo, Toleda, Master Chief and family, bcc9, The King, PMheart, Sherlocks, Micky1979, vit9696, vandroiy2013, Voodoo Team, Pike R. Alpha, lvs1974, Austere.J, CVad, Sampath007, onemanosx, erroruser, Jenny David, Olarila Facebook Community, Hackintosh Facebook Community and many others!
       
      We're all here to have fun and learn from each other!
×