Jump to content
InsanelyMac Forum
pepto

[GUIDE] Run macOS Sierra on a Dell Latitude E6320

Recommended Posts

Hi,

I need some help i hope you guys can help me out.

I installed the sierra on my computer, and it works perfect. Only problem I have that it's not boot only with the installer pendrive. I installed clover but it doesent mount EFI partition, I installed with an app, and copied the the EFI folder to the partition. I cant boot even in Legacy or UEFI.

Share this post


Link to post
Share on other sites
Advertisement

Hi,
thank you for this tuto very clear. OS sierra woks fine on dell e6320 i3.
But, I have a problem if you can help me. the step 14 for tuto doesn't works for me. the PC can't boot without the USB.
After type :
sudo diskutil corestorage revert /

error message :
/ is not a coreStorage Logical Volume

Thank you in advance

Share this post


Link to post
Share on other sites

The command should be:

sudo diskutil coreStorage revert <disk n>

not

sudo diskutil corestorage revert /

Simply check things 1st with command:

diskutil list

`

Eg:

sudo diskutil coreStorage revert disk1

or

sudo diskutil cs revert disk1

Share this post


Link to post
Share on other sites

I own the E6420, so far i know it has the same hardware. Do you have smooth scrolling at Sierra, or it is jumping line by line ?, i have rarely used it lately, and can't remember if it was so from the beginning.

Share this post


Link to post
Share on other sites

Wern, your signature shows an E6420 with the nVidia GPU... This guide is for the E6320 with HD3000 only and its principles are applicable to the E6220, E6420 and E6520 with HD3000 only.

Share this post


Link to post
Share on other sites

thx for reply

I type these command and the result below :

 

homes-MBP:~ home$ diskutil list

/dev/disk0 (internal, physical):

   #:                       TYPE NAME                    SIZE       IDENTIFIER

   0:      GUID_partition_scheme                        *250.1 GB   disk0

   1:                        EFI EFI                     209.7 MB   disk0s1

   2:                  Apple_HFS mac                     124.6 GB   disk0s2

   3:                  Apple_HFS Laptop                  124.3 GB   disk0s3

   4:                  Apple_HFS Untitled                650.0 MB   disk0s4

 

homes-MBP:~ home$ sudo diskutil coreStorage revert disk0

disk0 is not a CoreStorage Logical Volume

homes-MBP:~ home$ sudo diskutil coreStorage revert disk0s1

disk0s1 is not a CoreStorage Logical Volume

homes-MBP:~ home$ sudo diskutil coreStorage revert disk0s2

disk0s2 is not a CoreStorage Logical Volume

homes-MBP:~ home$ sudo diskutil coreStorage revert disk0s3

disk0s3 is not a CoreStorage Logical Volume

 
Finally no logical volume.
I don't understand, the EFI partition exists but no boot without USB.
 
 

Share this post


Link to post
Share on other sites

Well, you already were without logical volume when you listed them all... If the HDD still does not boot, try and re-install the bootloader on it.

Share this post


Link to post
Share on other sites

The E6x20 do not support UEFI mode well with OS X. Make sure you've kept your BIOS to Legacy mode or you'll have trouble booting OS X.

Share this post


Link to post
Share on other sites
Hi all,

Finally the issue is fixed after a full re-install.

Now, the e6320 i3 boots on the hard disk without need the USB key.

 

but, still no logical volume part --> this is no impact for the good functioning of hackintosh.

the last news, sierra is upgraded with app store without any trouble.

 

Big thx for your help.

Share this post


Link to post
Share on other sites

Install Dr Hurt's driver Release 4 + the posted PrefSettings & script. You may then adjust track speed through the TrackPad PrefPane.

How come the touchpad settings in the touchpad section dont work like it used to be in Yosemite and also the audio sounds distorted, I try your recommended solution but the touchpad setting gives me a error, any ideas?

Share this post


Link to post
Share on other sites

can someone help me on how to get the trackpad settings because is running laggy?

thanks in advance!!

For working trackpad settings copy the 10.11 "OldTrackpadTab.nib" from /System/Library/PreferencePanes/Trackpad.prefPane/Contents/Resources/YOURLANGUAGE.lproj to the same path @Sierra.

 

Maybe with this kext, the pointer is less laggy ApplePS2Controller.kext.zip

Share this post


Link to post
Share on other sites

For working trackpad settings copy the 10.11 "OldTrackpadTab.nib" from /System/Library/PreferencePanes/Trackpad.prefPane/Contents/Resources/YOURLANGUAGE.lproj to the same path @Sierra.

 

Maybe with this kext, the pointer is less laggy attachicon.gifApplePS2Controller.kext.zip

Can I do this with Yosemite instead of el Capitan because I don't have 10.11?

Share this post


Link to post
Share on other sites

I don't know, try it, or tell me what language you need, and i'll upload it.

I did and it works, thanks man! ,do I upload the kext you post it in system/library/extensions?

Share this post


Link to post
Share on other sites

Thanks Pepto for the Wonderfull guide. I was able to install Sierra 10.12.1 on a Dell E6420 with intel graphics and everything works fine. Only issue I faced is the machines goes into sleep mode after  logging in. When I press the power button, it comes back fine. Can you advise what could be the reason. Also the trackpad is not working. How to make it work.

 
Thanks again for the wonderful  guide

Share this post


Link to post
Share on other sites

I need advise on how to get clover to dual boot Sierra and windows 10 on E6420. I have installed Sierra first and after that installed Windows 10 on the same HDD. The DIsk is GPT and BIOS is set as legacy. Installed clover on the EFI partition but its unable to boot to windows 10. It says BOOTMGR is missing whenever i select windows 10. I can confirm windows 10 is booting whenever i choose the windows 10 partition as active. To boot to Sierra i have to make the EFI partition as active.

Share this post


Link to post
Share on other sites

hey, everything seemed to work great, i am on 10.12.1 now.. only issue i have is no sound. Sound buttons work, but it just shows speaker with a "no" sign. when i go into systems settings>sound there is nothing or sound output.... i tried installing VoodooHDA kext using the kext Wiz and it says it was installed but also says "no UUID"..... any help would be great! thanks for the great write up!!!

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.



  • Similar Content

    • By MaLd0n
      Nehalem, SandyBridge, IvyBridge, Haswell, Broadwell     Skylake, Kabylake and Coffeelake is here http://www.insanelymac.com/forum/topic/321872-guide-sierra-on-gigabyte-mobos-serie-200-kabylake-dsdt/   First...   ***Update bios to last available version!***   If you need a full patched DSDT...  -Extract tables with F4 key in Clover boot screen! -Run it and send me files! RunMe.app   Installation   --Create a bootable copy of macOS Sierra Check out the link http://www.insanelymac.com/forum/files/file/559-flash-drive-maker/   --Create a bootable copy of macOS HighSierra Check out the link http://diskmakerx.com/   --Install Clover in USB stick https://sourceforge.net/projects/cloverefiboot/files/Installer/   --Replace with my Clover folder CLOVER Install.zip   --Install Sierra/High Sierra and boot into system!   Post Installation --Install Clover and replace with my folder CLOVER Post Install.zip   --Reboot and activate video!   Bingo!   Now you need a fine tune! DSDT time!   --DSDT   Patches -FIX ERRORS AND WARNINGS -HPET -SATA -DMAC -SLPB -DARWIN -LPC -XHCI -PLUGIN TYPE -XXXX to HDEF -HDEF -RTC -IRQs -SBUS -BUS1 -MCHC -ALS0 -SHUTDOWN -LAN -USBX -PMCR -EC -PNLF -HDMI
       
      --Power Management
      - 1 Generation Intel Processors, use Generate P and C States in config.plist
      - 2 and 3 Generations Intel Processors, Generate SSDT with Piker script and drop CpuPm and Cpu0Ist SSDTs
      ssdtPRGen.command.zip
      Credits-https://github.com/Piker-Alpha/ssdtPRGen.sh
      - 4 Generation+ Intel Processors, use PluginType=1 in DSDT, SSDT or Clover config.plist
       
      for check Power, Frequency, Temperature and Utilization, use it
      Install Intel Power Gadget.pkg.zip
       
      --Brightness
      Install .app, select the required permission and reboot. Work in F1 / F2 keys!
      NativeDisplayBrightness.app.zip


      https://github.com/Bensge/NativeDisplayBrightness/releases
      *in some cases .app don't work, check patches in config.plist inside Clover folder Post Install
       
      --Clover
       
      https://sourceforge.net/projects/cloverefiboot/files/Installer/
       
      --AUDIO
       
      Use DSDT + AppleAlc
       
      --install Lan driver by Mieze
        -Atheros http://www.insanelymac.com/forum/files/file/313-atherose2200ethernet/   -Intel http://www.insanelymac.com/forum/files/file/396-intelmausiethernet/   -Realtek http://www.insanelymac.com/forum/files/file/88-realtekrtl8111-binary/   --Links   -FakeSMC https://bitbucket.org/RehabMan/os-x-fakesmc-kozlek   -Audio https://github.com/vit9696/AppleALC http://www.insanelymac.com/forum/topic/314406-voodoohda-289/   -USB https://bitbucket.org/RehabMan/os-x-usb-inject-all/downloads   It's time to Rock   -Credits and thanks to the old and new people in the community who developed patches, kexts and bootloaders!   Apple, Slice, Kabyl, usr-sse2, jadran, Blackosx, dmazar, STLVNUB, pcj, apianti, JrCs, pene, FrodoKenny, skoczy, ycr.ru, Oscar09, xsmile, SoThOr, RehabMan, Download-Fritz, Zenit432, cecekpawon, Intel, Oracle, Chameleon Team, crazybirdy, Mieze, Mirone, Oldnapalm, netkas, Elconiglio, artut-pt, ErmaC, Pavo, Toleda, Master Chief and family, bcc9, The King, PMheart, Sherlocks, Micky1979, vit9696, vandroiy2013, Voodoo Team, Pike R. Alpha, lvs1974, Austere.J, CVad and many, many, many others!   We're all here to have fun and learn from each other!  
    • By MaLd0n
      First... If you need DSDT edits... -Extract tables with F4 key in Clover boot screen! -Run it and send me files! RunMe.app   Installation --Create a bootable copy of El Capitan and Sierra Check out the link http://www.insanelymac.com/forum/files/file/559-flash-drive-maker/   --Create a bootable copy of macOS HighSierra Check out the link http://diskmakerx.com/   --Install Clover in USB stick https://sourceforge.net/projects/cloverefiboot/files/Installer/   --Replace with my Clover folder CLOVER Install.zip   --Install EL Capitan / Sierra / High Sierra and boot into system! for Sierra/High Sierra you need a Processor with SSE4.1 instruction   Post Installation --Install Clover and replace with my folder CLOVER Post Install.zip   --Reboot and activate video!   Bingo! Now you need a fine tune! DSDT Time! -Post your full Clover folder with original tables in Origin folder(Extract with F4 in Clover boot screen) and tell me what your hardware! -Post Ioreg, extract with Ioreg Explorer http://www.insanelymac.com/forum/index.php?app=core&module=attach&section=attach&attach_id=222606 -Run it, post files generate in your desktop http://www.insanelymac.com/forum/index.php?app=core&module=attach&section=attach&attach_id=222609    My DSDT GA P35-DS3 DSDT.MaLd0n LGA775.zip   Patches -FIX ERRORS AND WARNINGS -HPET -SATA -SLPB -DARWIN -LPC -HDEF -RTC -EHCI -UHCI -IRQs -SBUS -BUS1 -MCHC -ALS0 -SHUTDOWN -LAN -EC -PNLF --Native Power Management
       
      Use Clover, check Generate P and C States
       
      --Brightness
      Install .app, select the required permission and reboot. Work in F1 / F2 keys!
      NativeDisplayBrightness.app.zip


      https://github.com/Bensge/NativeDisplayBrightness/releases
      *in some cases .app don't work, check patches in config.plist inside Clover folder Post Install
       
      --AUDIO
       
      Device HDEF + AppleAlc + Lilu
       
      --install Lan driver by Mieze
        -Atheros http://www.insanelymac.com/forum/files/file/313-atherose2200ethernet/   -Intel http://www.insanelymac.com/forum/files/file/396-intelmausiethernet/   -Realtek http://www.insanelymac.com/forum/files/file/88-realtekrtl8111-binary/   --Links   -FakeSMC https://bitbucket.org/RehabMan/os-x-fakesmc-kozlek   -Audio https://github.com/vit9696/AppleALC http://www.insanelymac.com/forum/topic/293863-applehda-patch-requests/   -Credits and thanks to the old and new people in the community who developed patches, kexts and bootloaders!   Slice, Kabyl, usr-sse2, jadran, Blackosx, dmazar, STLVNUB, pcj, apianti, JrCs, pene, FrodoKenny, skoczy, ycr.ru, Oscar09, xsmile, SoThOr, RehabMan, Download-Fritz, Zenit432, cecekpawon, Intel, Apple, Oracle, Chameleon Team, crazybirdy, Mieze, Mirone, Oldnapalm, netkas, Elconiglio, artut-pt, ErmaC, Pavo, Toleda, Master Chief and family, bcc9, The King, PMheart, Sherlocks, Micky1979, vit9696, vandroiy2013, Voodoo Team, Pike R. Alpha, lvs1974, Austere.J, CVad and many, many, many others!   We're all here to have fun and learn from each other!   ENJOY!  
    • By Gymnae
      This guide guide is a work in progress
       
      Introduction
      The H370 chipset powers 8th generation Core-i CPUs by Intel and is actually much newer than the Z370, even though it name implies otherwise. The H370 requires new approaches compared to the Z370, since it includes newer or different components. An example would be on-die USB 3.1 and WiFi support.
      Since this guide is not a "hold-your-hand-every-step" guide, I assume you know:
      Clover installation and configuration How to create an install medium BIOS configuration and access Have heard of ACPI patching (I'm a newb at this myself)  
      What works
      Sleep (via DSDT edits and emulated NVRAM) on-board Audio (via CloverALC script) Native PM (without any kext or patch) All USB ports iGPU for both acceleration and display dGPU (I'm running an Nvidia GTX 1080)  
      Untested
      NIC --> I'm using WiFi only  
      What doesn't work
      Native NVRAM via AptioMemoryFix.efi DMVT Pre-alloc higher than 64MB (but not necessary)  
      1. Installation
      This guide heavy inspired by the work of /u/corpnewt of /r/hackintosh and his (sorta) Vanilla guide
       
      1.1 Create the install media for MacOS
      Follow this, if you are using a Mac to start off with. If you are totally new to MacOS, then please check the basic guide Creation of an installer media in windows or linux
       
      1.2 Install Clover on the install media
      Using the Clover installer, ensure you are installing to the USB medium you are using for the installer.
      Chose the following options:
      AptioMemoryFix UEFI booting only Install to ESP You have to get your hands on an apfs.efi. A google search can help, or extracting it from the Installer package. Make sure you procure a version matching the MacOS version you are about to install. Place the apfs.efi in drivers64UEFI.
       
      1.2 Adjust the config.plist for the installer
      You can use the config.plist attached as a guideline, but take a look at it before and at least adjust the SMBIOS - otherwise it won't boot.
      Attention: The attached plist contains audio patches introduced by a post-install step. If you run into problems, you might remove those. It also contains a manual slide value, which should normally not be needed, but works fine for me. It is also tuned for usage with an Nvidia Pascal dGPU as main GPU.
       
      The config you create now should serve you nicely for install and running the system.
       
      Take care of adding the following basics:
      SMBIOS: iMac18,3 - You can generate a serial number via Clover Configurator. The creation of a proper SMBIOS is covered in many guides to good extend Look at the graphics section and adjust the injection for Intel to your situation  
      Fixes

      Patches

      Devices

      Graphics

      Kernel and Kext patches
       
      1.3 kexts and friends
      Add the supplied SSDT-UAIC.aml to "patched" - it limits the injected USB Ports to the actual number and ports valid for this board.
       
      Required kexts on "Other":
      FakeSMC.kext IntelGraphicsFixup.kext Lilu.kext When having an Nvidia card: NvidiaGraphicsFixup.kext IntelMausiEthernet.kext in case you're running Ethernet USBInjectAll.kext with the HCI-300-series-injector.kext --> These two should be installed to /L/E after install  
      We are leaving sound out at the moment, this is something for post-install. Please note the absence of Shiki, I don't find it necessary. Video material I tried made use of the iGPU without shiki.
       
      1.4 Check BIOS and install
      You should be ready for install. But before you reboot, please take a look at your BIOS and set it up accordingly (copied from the aforementioned guide and adapted):
      Load Optimized Defaults Disable VT-d setting If your system has Secure Boot Mode, disable it Set OS Type to Windows 8/10 or OtherOS - I have not seen a difference Turn off internal Serial and Parallel port Turn off Network stack for boot Turn off wake-on-lan (for now) Set XHCI Handoff to Enabled Don't enable decode over 4G Depending on your GPU, set priority for boot Set internal GPU to enable Set DMVT pre-alloc to 64MB Set USB legacy to enabled Activate XMP profile 1 f your Ram has it (mine doesn't and I added the timings manually) Set ERP to enable, disable platform power management (I need to do more research if this could be enabled)  
      I've attached my current BIOS config "hack2". You can place that on a fat32 drive (the EFI partition of your install USB drive might be an idea) and see if it loads. It's made for and with the F2 BIOS.
       
      The install itself should be like other MacOS Hackintosh installs with it several reboots and ensuring to select the correct boot device in Clover.
       
      2. Post-install
       
      2.1 Install clover on target
      This is a no-brainer, but install a fresh copy of Clover on your target medium.
       
      During install select again AptioMemoryFix but also additionally
      EmuVariableUefi-64.efi Install RC scripts on target volume because otherwise NVRAM doesn't seem to work
       
      After the install, copy
      config.plist contents of "Other" content of "patched" apfs.efi from drivers64UEFI to your new clover install.
       
      2.1 Edit DSDT for slumber
      This is necessary only once on initial install and every time, you edit or upgrade the BIOS. The DSDT.aml attached to this post might work for your system or give you a file to compare to. Don't expect it to work for you, though.
      I won't go into the details of DSDT extraction and patching. There are better guides (the linked guide is a rip-off of rehabman's guide from a different forum). Please follow such a guide to extract your ACPI data.
       
      Locate and disassemble the DSDT with the newest iasl binary you can put your hands on, then open it with MacIASL in its newest version you can find (Hint: Here is a good source) You can check if the version is new enough if MacIASL doesn't throw error upon compiling a freshly extracted DSDT.aml or DSDT.dst
       
      Add rehabmans repo (as per linked guide) and apply the following patches:
      Rename _DSM to _XDSM Fix _WAK Arg0 v2 USB3 _PRW 0x6D Skylake (instant wake) Find the CNVW device and remove the _PWR function there.
       
      Compile the DSDT and place it in "patched".
       
      2.2 Install kexts to system
      As mentioned in the install section, it's better to follow rehabman's instruction and install USBinjectAll.kext to /L/E:
      sudo cp -R Release/USBInjectAll.kext /Library/Extensions sudo touch /System/Library/Extensions && sudo kextcache -u / 2.3 Enable onboard Audio
      This is where I'm not so happy currently, I'd like it to work without altering AppleHDA. But currently I find no other way.
       
      2.3.1 Install FakePCIID & FakePCIID_Intel_HDMI_Audio
      Rehabman tells us to use a kext installer to install it to /S/L/E. Chose the RELEASE folder
       
      2.3.2 Run CloverALC command
      Ensure your EFI partition is mounted before running this command
      Get the newest version of CloverALC command (audio_cloverALC-xxx.sh) and run it. Our Audio codec is RTL887 and I'm running with layout ID 1
       
      2.4 Optional steps
      If you have a dGPU, now it's the time to install its drivers and adjust the config.plist for it.
      This is out of scope of this guide. Yet, my supplied config.plist is ready to be used with Nvidia Pascal cards and using the Nvidia web driver.
       
      3. ToDo
      Move away from static DSDT patching to SSDT hotpatching --> requires my work Native NVRAM --> requires developer work Audio without AppleHDA patching --> requires developer work  
      4. Thanks to
      @MaLd0nfor helping finding the right way with the DSDT
      @RehabMan, for being a legend and helping me out patching
      @toleda, for audio patches for the 300 series
      /u/corpnewt, for his superb vanilla guide
      @wmchris for his super XPS 9550 guide and introducing me to hot-patching
      all the developers of clover and it's awesomeness
       
      SSDT-UIAC.aml
      config.plist
      DSDT.aml
      hack2
    • By frankiee
      Hi there, time for my first guide after asking so many things
       
      Updated for newer Clover versions and with additional instructions for more apps: gdisk and RU.
       
      So what may be overlooked sometimes in the whole boot loader discussion is the ability of UEFI to do more than just loading an OS. This is why I see ".efi" files as "apps" because in fact they just are, built on a special kind of API: UEFI. So, you can actually do stuff like editing, diagnosing, testing certain stuff at the lowest possible system level without booting to any OS.
       
      DISCLAIMER: Use this guide at your own risk! For educational purposes only! Should do not any harm, but remember you are dealing with rather low level stuff. But at least for me everything went flawless.
       
      Prerequisites:
      Working clover installation Clover Configurator or some app to edit the config.plist  
      1) Memtest
       
      This is how to install the UEFI version of Memtest with Clover:
      Download memtest, I used this link: Image for creating boot-able USB Drive Open the archive by double clicking on it. Mount the file memtest86-usb.img within by double clicking again. Now, you should see a folder named EFI in this volume, containing a folder BOOT. Open it. The files containing it are the actual app, in 32 and 64 bit versions. Think in almost all cases we want to use the 64 bit version. Now, mount your EFI partition, using Clover configurator. Create a folder named MemTest86 in the EFI folder on your main drive. Copy all files in the EFI/BOOT folder from the mounted image to your newly created folder. That ends the basic setup! Now, we add the correct Menu entry to the clover boot menu, so that we can actually start this app.
       
      Get into clover configurator, open your standard config.plist from your boot drive and go to the GUI section. Under "Custom Entries", add an entry like this:
       

       
      Please note while the path you enter is not case sensitive, you must make sure you use the backslash "\" for entering paths, and not a slash. So basically what we do is tell clover where it can find the app, give it a name, and tell clover it is a "Windows" app. Note: with older Clover versions we had to set this to "Linux", but for now "Windows" is the setting that works.
       
      If you prefer to do a manual config, add this entry to your config.plist, under GUI/Custom/Entries:
      <dict> <key>CustomLogo</key> <true/> <key>Disabled</key> <false/> <key>FullTitle</key> <string>MemTest86</string> <key>Hidden</key> <false/> <key>Ignore</key> <false/> <key>Image</key> <string>\EFI\CLOVER\themes\Icons\os_mint.png</string> <key>Path</key> <string>\EFI\MemTest86\BOOTX64.efi</string> <key>Type</key> <string>Windows</string> <key>VolumeType</key> <string>Internal</string> </dict> Now, save and reboot and you should see the newly created entry. Note that I also used a custom Icon - this is optional - in case you don't you will just see a generic windows icon instead:
       

       
      And this is how it looks like:
       

       

       
      PS: also noticeably faster and you get also more features with this version than with the older version, for example it does now write a log file. For more Information, see: http://www.passmark.com/forum/showthread.php?4315-Memtest86-Version-5-Beta-%28Pure-UEFI%29
       
       
      2) gdisk
       
      Another app you can use is the UEFI version of gdisk (aka GPT fdisk), which you can use to edit and change your partitions.
       
      Warning! Install and use this app at your own risk! If you do something wrong here you might nuke your drive(s), so only use that if you know what you are doing.
       
      This is how to do it (even easier):
      Download here: https://sourceforge.net/projects/gptfdisk/files/gptfdisk/1.0.1/gdisk-binaries/gdisk-efi-1.0.1.zip/download Mount your EFI partition Unzip the file and copy the resulting folder to your EFI Folder, so your path goes like this "/Volumes/EFI/EFI/gdisk-efi" Get into clover configurator, open your standard config.plist from your boot drive and go to the GUI section. Add an entry like this:  
      If you prefer to do a manual config, add this entry to your config.plist, under GUI/Custom/Entries:
      <dict> <key>CustomLogo</key> <false/> <key>Disabled</key> <false/> <key>FullTitle</key> <string>GDisk</string> <key>Hidden</key> <false/> <key>Ignore</key> <false/> <key>Image</key> <string></string> <key>Path</key> <string>\EFI\gdisk-efi\gdisk_x64.efi</string> <key>Type</key> <string>Windows</string> <key>VolumeType</key> <string>Internal</string> </dict> When everything went OK you should see this after selecting the respective entry in Clover:
       

       
       
      3) RU
       
      I recently found one more app that might be interesting to some, and thats "Read Universal" or in short "RU". This is a tool that enables you to debug your BIOS and read (and modify!) every imaginable data, including UEFI variables, ACPI Tables etc.
       
      Warning, again! I think blindly messing around with this app is even more dangerous, but on the other hand it gives you access to a lot of potentially interesting stuff.
      Download here: http://ruexe.blogspot.de/ The next steps are basically the same as above so make a folder in your EFI partition, copy the .EFI files and make another custom entry in your config.plist Here are some screens:
       

       

       

       
       
      So this is what you also can do with UEFI and clover. I am curious which other useful applications might exist!
       
      Anybody who knows, maybe post it here?
    • By fantomas1
      Hi InsanelyMacaholics   

      Use this thread to link / talk about of the future Nvidia Web Driver updates for macOS Sierra.
       
      10.12.6
      Nvidia Web Driver - 378.02.02.25f08 --> build 16G1314 (thanks to BreBo)  New!
      Nvidia Web Driver - 378.02.02.25f07 --> build 16G1314 (thanks to haring)
      Nvidia Web Driver - 378.05.05.25f06 --> build 16G1212 (thanks to WeBeRiO)
      Nvidia Web Driver - 378.05.05.25f04 --> build 16G1114 (thanks to lukazm)
      Nvidia Web Driver - 378.05.05.25f03 --> build 16G1036 (thanks to Gradou)
      Nvidia Web Driver - 378.05.05.25f01 --> build 16G29 (thanks to Badruzeus)
       
       
      10.12.5
      Nvidia Web Driver - 378.05.05.15f01 --> build 16F73 (see this post)
       
       
      10.12.4
      Nvidia Web Driver - 378.05.05.05f02 --> build 16E195(thanks to crachmaster4999)
      Nvidia Web Driver - 378.05.05.05f01 --> build 16E195 (thanks to Moviemakergr)  Pascal support!!!
      Nvidia Web Driver - 367.15.10.45f01 --> build 16E195 (thanks to Lanc)
       
       
      10.12.3

      Nvidia Web Driver - 367.15.10.35f01 --> build 16D32 (thanks to shatterhenner)
       
       
      10.12.2
      Nvidia Web Driver - 367.15.10.25f02 --> build 16C68 (see this post)
      Nvidia Web Driver - 367.15.10.25f01 --> build 16C67 (see this post)
      Nvidia Web Driver - 367.15.10.25b06 --> build 16C60b/16C63a (see this post)
       
       
      10.12.1
      Nvidia Web Driver - 367.15.10.15f03 --> build 16B2657/16B2659 (thanks to Moviemakergr).
      Nvidia Web Driver - 367.15.10.15f01 --> build 16B2555 (thanks to Moviemakergr)
       
       
      10.12.0
      Nvidia Web Driver - 367.15.10.05f01 --> build 16A323 (thanks to phi777)
       
       
      GM
      Nvidia Web Driver - 367.10.10.05b01 --> build 16A323 (same driver since DP4/PB3)
      Nvidia Web Driver - 367.10.10.05b01 --> build 16A322 (see this post)
      Nvidia Web Driver - 367.10.10.05b01 --> build 16A320 (see this post)
       
       
      DP/PB
      Nvidia Web Driver - 367.10.10.05b01 --> build 16A313a (DP8 & PB7) (see this post)
      Nvidia Web Driver - 367.10.10.05b01 --> build 16A304a (DP7 & PB6) (see this post)
      Nvidia Web Driver - 367.10.10.05b01 --> build 16A294a (DP6 & PB5) (see this post)
      Nvidia Web Driver - 367.10.10.05b01 --> build 16A286a (DP5 & PB4) (see this post)
      Nvidia Web Driver - 367.10.10.05b01 --> build 16A270f (DP4 & PB3) (thanks to TheRacerMaster)
      Nvidia Web Driver - 367.05.10.05b07 --> build 16A254g (DP3 & PB2) (see this post)
      Nvidia Web Driver - 367.05.10.05b07 --> build 16A238m (PB1) (thanks to Faun) 
      Nvidia Web Driver - 367.05.10.05b07 --> build 16A239j (DP2) (thanks to Faun)
      Nvidia Web Driver - 367.05.10.05b03 --> build 16A201w (DP1) (thanks to Xmedik)
       
×