Jump to content
tluck

[GUIDE] Lenovo T460 macOS with Clover

855 posts in this topic

Recommended Posts

On 8/27/2018 at 2:41 AM, beatifullive said:

how did u disable nvida?

Did not need to. My t470 is i5-6300u with only intel 520 graphics. I do not have any discrete graphics.

Share this post


Link to post
Share on other sites
Advertisement
5 hours ago, kolodzieski said:

Did not need to. My t470 is i5-6300u with only intel 520 graphics. I do not have any discrete graphics.

Fixed by hotpatch with RehabMan's driver.

1. Use the SSDT-DDGPU.dsl in https://github.com/RehabMan/OS-X-Clover-Laptop-Config/tree/master/hotpatch

2. Find out special 940mx device name in _ini and _off method in the disasemble *.dsl file(follow this link:https://www.tonymacx86.com/threads/guide-disabling-discrete-graphics-in-dual-gpu-laptops.163772/)

3. Follow the grammar of example in SSDT-DDGPU.dsl , add _off method and external method lines.

4. attach file will be upload later..

Edited by beatifullive

Share this post


Link to post
Share on other sites

Hello

 

I have done a clean install from High Sierra 10.13.6 on T460

 

I follow exactly your steps. I have several issues :

- the following instruction :

sudo diskutil corestage revert /

doesn't work

 

- I have no sound at all

- trackpad is working strangely

- in Clover, there are several choices (prebooter). Is it normal?

- in Safari, sometimes it's a bit laggy when there are ads with video for instance

 

Thank you for your help and nice job tluck

Share this post


Link to post
Share on other sites
On 9/2/2018 at 6:07 AM, Mat said:

Hello

 

I have done a clean install from High Sierra 10.13.6 on T460

 

I follow exactly your steps. I have several issues :

- the following instruction :


sudo diskutil corestage revert /

doesn't work

 

- I have no sound at all

- trackpad is working strangely

- in Clover, there are several choices (prebooter). Is it normal?

- in Safari, sometimes it's a bit laggy when there are ads with video for instance

 

Thank you for your help and nice job tluck

 

I have a t470, and needed to inject 29 instead of 28 for sound on my laptop. My trackpad was not working well. I installed the latest VoodoPS2Controller kext from RehabMan on tonymac, and my trackpad works great. Your milage may vary. 

Share this post


Link to post
Share on other sites
On 8/20/2018 at 12:01 PM, verleihnix said:

 

@Blaggah Could you please share your voodoops2 kext from x1 carbon

I apologize for the delay, I will uploaded the kext later when I get home. Just recently moved to a new place and have been super busy with that. 

Here's the voodoops2 kext you requested @verleihnix

VoodooPS2Controller.kext.zip

Edited by Blaggah

Share this post


Link to post
Share on other sites

Here is a new T470.zip to use an an overly on the @tluck repository. 

 

The battery path for the dsdt has changed to support fan reporting. Also the SSDT-XHC-T470 supports just the ports on my T470, so the clover patch to inject more USB port is no longer required. 

 

Cheers,

Scott. 

T470.zip

Share this post


Link to post
Share on other sites

Hi guys,

 

Got my hands on a T470s and got high Sierra working - as is it boots fine and seems to be ok, however:

 

Trackpad does not act great, no option in sys prefs to change

 

Also battery indicator in menu bar unable to show.

 

Not really versed on DSDT edits however am keen to learn.

 

Anybody have one of these machines that can offer any advice?

 

2.9ghz i7

Intel HD 620

Share this post


Link to post
Share on other sites
On 9/8/2018 at 7:31 PM, kolodzieski said:

Here is a new T470.zip to use an an overly on the @tluck repository. 

 

The battery path for the dsdt has changed to support fan reporting. Also the SSDT-XHC-T470 supports just the ports on my T470, so the clover patch to inject more USB port is no longer required. 

 

Cheers,

Scott. 

T470.zip

I get 500 error when try to download file. Can you check please??

 

Thanks!!

Share this post


Link to post
Share on other sites
5 hours ago, m1gue said:

Finally you can download the ZIP.
After following the steps I have a KP unless I use noSKL.

IMG_1507.thumb.jpg.8bbdfafe43a8d9dd685f8217387d356e.jpg

Thanks

I would try an get the install done without any ACPI/patched files. I think the supplied config.plist should be okay for first time boots. 

 

Do you have a T470? T460? What processor? I am have a i5-6300u, with HD520 graphics.

Share this post


Link to post
Share on other sites
2 hours ago, kolodzieski said:

I would try an get the install done without any ACPI/patched files. I think the supplied config.plist should be okay for first time boots. 

 

Do you have a T470? T460? What processor? I am have a i5-6300u, with HD520 graphics.

Now...

T470

i5-7200U

 

I have followed this guide + Readme on: https://github.com/tluck/Lenovo-T460-Clover/tree/master/DSDT.T470

Content similar to T470.zip

Share this post


Link to post
Share on other sites

Seems solved with: IntelGraphicsDVMTFixup.kext_1.2.2 and without glinchs with this ig-platform-id: 0x591b0000.

 

Also download last versions from: Lilu, WhateverGreen and AppleALC

 

With Graphics ok I can get DisplayID for patch AppleBacklightInjector and get brightness control: F10T243d

  

 

Edited by m1gue

Share this post


Link to post
Share on other sites

Finally I went back to Sierra...

 

Do you have troubles after sleep with Bluetooth?

 

Other point : we can see the change between the first and second battery (it goes like putting on power)

 

Anyone else?

Share this post


Link to post
Share on other sites
On 9/18/2018 at 2:07 PM, Mat said:

Finally I went back to Sierra...

 

Do you have troubles after sleep with Bluetooth?

 

Other point : we can see the change between the first and second battery (it goes like putting on power)

 

Anyone else?

With a stock BrcmPatchFix2 yes I had blootooh randomly stop after wake. It seems much better using the distributed BrcmPatchFix2 from @tluck. 

 

Dual batteries work fine with my patched DSDT, and the BATC SSDT. Those are setup for a T470 with i5-6500u. You may have to create your own patches or blend some together. 

Share this post


Link to post
Share on other sites
On 9/19/2018 at 7:57 PM, lisnake said:

Anyone managed to install Mojave on T460/T470?

Yes, booted in to Mojave having acceleration enabled.

I used native lilu, applealc and whatevergreen kext.

Delete IntelGraphicsDVMTFixup and IntelGraphicsFixup kext.

That works fine for High Sierra as well.

Edit config.plist:

Change Graphics Inject Intel to false

Add under Devices

        <key>Properties</key>
        <dict>
            <key>PciRoot(0x0)/Pci(0x2,0x0)</key>
            <dict>
                <key>AAPL,ig-platform-id</key>
                <data>
                AAAWGQ==
                </data>
                <key>device-id</key>
                <data>
                FhkAAA==
                </data>
                <key>enable-hdmi20</key>
                <data>
                AQAAAA==
                </data>
                <key>framebuffer-fbmem</key>
                <data>
                AACQAA==
                </data>
                <key>framebuffer-patch-enable</key>
                <data>
                AQAAAA==
                </data>
                <key>framebuffer-stolenmem</key>
                <data>
                AAAwAQ==
                </data>
                <key>framebuffer-unifiedmem</key>
                <data>
                AAAAgA==
                </data>
            </dict>
        </dict>
 

 

Edited by verleihnix

Share this post


Link to post
Share on other sites
On 9/20/2018 at 5:06 PM, kolodzieski said:

With a stock BrcmPatchFix2 yes I had blootooh randomly stop after wake. It seems much better using the distributed BrcmPatchFix2 from @tluck. 

 

Dual batteries work fine with my patched DSDT, and the BATC SSDT. Those are setup for a T470 with i5-6500u. You may have to create your own patches or blend some together. 

Hello

 

Thank you for your help. I have done my own ACPI files extract, is it what you're talking about when you say "my patched DSDT"? And the BATC SSDT is included in tluck package?

 

And as I use tluck package so I have the BrcmPatchFix2 from tluck ?

 

Thanks!

Share this post


Link to post
Share on other sites
On 9/21/2018 at 10:25 PM, verleihnix said:

Yes, booted in to Mojave having acceleration enabled.

 

Hi, I'm on a T460 and I tried an upgrade from 10.13 to 10.14 (after upgrading Clover, updating Lilu and installing whatevergreen, etc.) and now I'm not able to boot into Mojave even with those config.plist changes you mentioned. Can I see your EFI/Clover folder? I feel like I'm missing something. From what I saw in verbose mode the problems seem to be related to the framebuffer patches

Share this post


Link to post
Share on other sites

I used clover 4670 from tluck t420 pack.

And the the new virtualsmc.

but that should not be the problem.

To get back into OS you can mod graphics platform ID to 0x12345678 manually during clover boot.

EFI.zip

Share this post


Link to post
Share on other sites
1 hour ago, giovahkiin said:

 

Hi, I'm on a T460 and I tried an upgrade from 10.13 to 10.14 (after upgrading Clover, updating Lilu and installing whatevergreen, etc.) and now I'm not able to boot into Mojave even with those config.plist changes you mentioned. Can I see your EFI/Clover folder? I feel like I'm missing something. From what I saw in verbose mode the problems seem to be related to the framebuffer patches 

something output in verbose similar like this?

also need help, please enlight me what the problem is.....:help:

2075565418_IMG_20180927_154241_.thumb.jpeg.5d5068b39e0ad8a67311d5d22f288de1.jpeg

Share this post


Link to post
Share on other sites
3 hours ago, verleihnix said:

I used clover 4670 from tluck t420 pack.

And the the new virtualsmc.

but that should not be the problem.

To get back into OS you can mod graphics platform ID to 0x12345678 manually during clover boot.

EFI.zip

Yeah, I'm also using 4670 but from the latest push to tluck's T460/70 repo. I tried matching some of my kexts with yours (such as VirtualSMC) but that didn't have much of an effect. I even tried outright using your entire EFI/Clover folder and it still bootloops. Even injecting the platform ID to 0x12345678 doesn't work. I guess I'll be forced to clean install Mojave?

Share this post


Link to post
Share on other sites
5 hours ago, verleihnix said:

I used clover 4670 from tluck t420 pack.

And the the new virtualsmc.

but that should not be the problem.

To get back into OS you can mod graphics platform ID to 0x12345678 manually during clover boot.

EFI.zip

 

2 hours ago, giovahkiin said:

Yeah, I'm also using 4670 but from the latest push to tluck's T460/70 repo. I tried matching some of my kexts with yours (such as VirtualSMC) but that didn't have much of an effect. I even tried outright using your entire EFI/Clover folder and it still bootloops. Even injecting the platform ID to 0x12345678 doesn't work. I guess I'll be forced to clean install Mojave?

 

I eventually figured it out. It's really silly, but while I did update my EFI before updating to Mojave, I didn't update the kexts in /L/E. I ended up fixing the problem using Windows and the macOS Recovery (thank God for that). I copied over the new kexts, touch /L/E and kextcache. I might still have to fix a few things, but so far Mojave runs with essentially everything from High Sierra working.

 

image.thumb.png.67fc7b130e54468ce0e23d9c81b7c33a.png

Share this post


Link to post
Share on other sites
21 hours ago, fudaming said:

something output in verbose similar like this?

also need help, please enlight me what the problem is.....:help:

 

 

after update kexts and rebuild the cache, got Mojave installed finally. but I believe there is something wrong with graphic driver....

854082298_2018-09-2814_10_09.png.2a59c7d085a143807d1fc37f5536c849.png

Share this post


Link to post
Share on other sites
6 hours ago, Fleshboy55 said:

that is very useful, I think seems to be installed properly, very big thanks to Fleshboy55.

 

However, I still want to figure out whats the problem of my config, Kext files, or config.plist.

I will try to write a config.plist of myself with your kexts, and see if it can bootup in a right way.

 

thanks again Fleshboy55!!

908496548_2018-10-0118_48_51.png.0b23e7f24b9a6308c34e476c63e89d4e.png

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Content

    • By ludufre
      Installing macOS Mojave on Lenovo ThinkPad L440

       
      There are two version of this laptop:
      - 20AS = Chipset QM87, without Express Card (mine).
      - 20AT = Chipset HM86, with Express Card.
      I strong believe is the same thing...
       

      Changelog:
       
      06/09/2019 14:16h GMT-0
      - Added missing parts in the post-install step. 
       
      06/04/2019 17:19h GMT-0
      - Updated Clover link. 
       
      06/02/2019 18:08h GMT-0
      - Added info about update 10.14.5. 
       
      03/13/2019 13:15h GMT-0
      - Updated info about touchpad replacement and CPU and 4G LTE modem.
       
      02/05/2019 18:47h GMT-0
      - Updated info about CPU replacement and 4G LTE modem.
       
      02/04/2019 15:24h GMT-0
      - Sometimes the VoodooHDA.kext doesn't work.
      - Added AppleHDADisabler.kext to fix that (attached bellow).
       
      01/24/2019 14:42h GMT-0
      - Added more adjustments to use of VoodooHDA.
      - Updated VoodooHDA links to 2.9.1 official (without installer).
      - Changed PCM volume from 90 to 180 in Info.plist (attached modified VoodooHDA.kext bellow)
      - Updated SSDT-L440.aml (Removed HDEF and HDAU, not needed).
      - Updated config.plist (Changed to user Audio layout to 1).
       
      01/22/2019 20:47h GMT-0
      - I gave up on the AppleALC.
      - Headset does not work.
      - Now with VoodooHDA is perfect and the sound even louder.
       
      01/22/2019 14:37h GMT-0
      - Added info about update 10.14.3. 
       
      01/22/2019 13:46h GMT-0
      - Added link to BIOS reassing guide.
       
      01/20/2019 11:49h GMT-0
      - First version.
       
      What works and what does not
       
      - Processor: Intel Core i5-4300M ->  Work. All SpeedStep stages.
      - Video Card: Intel HD4600 ->  Work. QE/CI and Metal.
      - Chipset: Intel QM87 ->  Work.
      - Mini DisplayPort ->  Work. But no audio, yet.
      - VGA ->  Not work. Normal.
      - Audio: ALC292 ->  Work.
      - WiFi/Bluetooth: Intel AC 7260 ->  Not work. Replaced with DW1560 (need whitelist removal).
      - Ethernet: Intel I217-LM ->  Work.
      - Card Reader: Realtek RTS5227 ->  Not work.
      - Keyboard and Touchpad ->  Work.
      - Webcam ->  Work.
      - Fingerprint Reader ->  Not work. Normal.
      - USB3.0 ->  Work.
      - Sleep ->  Work.
      - Airdrop, Handoff, Instant Hotspot and Continuity ->  Work after replaced wireless.
       
       
      Extras
       
      - FullHD 1920x1080 display upgrade: 
      Replaced with AU Optronics B140HAN01.1 30pin eDP (B140HAN01.2 and B140HAN01.3 also compatible).
      Apparently same screen as Dell Latitude E6440, E7440, Lenovo Ideapad U430 and E129.
       
      - CPU upgrade:
      Replaced the stock Intel Core i5 4300M 2.6Ghz (3.3Ghz turbo) 6M cache with Intel Core i7 4700MQ 2.4Ghz (3.4Ghz turbo) 6MB.
      I initially had problems with overheating. The processor ran at full load above 90 degrees.
      After using a quality thermal paste I can work between 70 and 80 degrees.
      Acceptable taking into consideration that the new processor has 47TDP versus 37TDP which is recommended.
      I also had no problem consuming the battery while charging. The original 65W source seems to have figured out.
       
      - Touchpad upgrade:
      Replaced the stock with T460 touchpad.
      This is serious: you have to do it! It should be stock. Touchpad with precision and absurd quality!
      Just do it!
       
      - RAM upgrade:
      No mistery here. Just upgade.
       
       
      Todo
       
      - Make DP audio work.
      - Make Card Reader work.
      - Upgrade CPU to i7-4712MQ (Ordered. It's on the way) Done, but received i7-4700MQ (47w TDP, with good paste I have no overheating)
      - Replace touchpad with T460 model (Ordered. It's on the way) Done. Sensitivity and perception of quality much better. I recommend 100%!
      - Sierra Gobi5000 4G LTE modem EM7355 (Ordered. It's on the way. I hope works. ) Done, but not work. Recognize but not connect. I already gave up...
      - Upgrade to 16GB RAM Done
      - Make trackpad appear in System Preferences
       
       
      What you need to install

      - Running install of macOS
      - One USB flash drive of 8GB or bigger
      - macOS Mojave install app
      - Clover EFI
      - Clover Configurator
      - Some KEXTs and SSDT patches


      How create create the install flash drive
       
      Prepare install flash drive

      Format the flash drive with GUID partition mapping and name it "Install".

      - Open Disk Utility.
      - Click in View, then "Show All Devices".
      - Select the destination flash drive, then Erase.
      - Name: Install, Format: Mac OS Extended (Journaled) and Scheme: GUID Partition Map
       
      Create install flash drive

      Open terminal and run this command:
      sudo /Applications/Install\ macOS\ Mojave.app/Contents/Resources/createinstallmedia --volume /Volumes/Install --nointeraction This will take about 30 minutes.
       


      Install bootloader

      Download the CloverEFI from SourceForge (used 4934) and install with this options on "Install macOS Mojave":
       
      - Install for UEFI booting only
      - Install Clover in the ESP
      - UEFI Drivers - ApfsDriverLoader-64
      - UEFI Drivers - AptioMemoryFix-64


       
       
      Make things works

      Will be created a partition named EFI and mounted in Desktop.
      - Replace the /Volumes/EFI/CLOVER/config.plist with mine attached below
                    If you have modded BIOS with Advanced Menu and enabled 128MB DRAM-prealloc use 128MB_DRAM-prealloc_config.plist.zip
                    If no, then use 32MB_DRAM-prealloc_config.plist.zip
      - Put SSDT-L440.aml attached below in /Volumes/EFI/CLOVER/ACPI/patched/
       
      Generate your Serial, MLB and SmUUID
       
      - Open the replaced config.plist with Clover Configurator (used 5.3.2.0)
      - Go to SMBIOS, click few times in "Generate New" in Serial Number and SmUUID.
       
      Download those Kexts and put in /EFI/CLOVER/kexts/Other/
       
      - Download the HWSensors 3 from here. I used the FakeSMC.kext, ACPIMonitor.kext and IntelCPUMonitor.kext inside of DMG version r196.
      - Download the VoodooPS2Controller.kext from here. I used version 2018-1008.
      - Download the IntelMausiEthernet.kext from here. I used the version 2018-1031.
      - Download the Lilu.kext from here. I used the version 1.3.6.
      - Download the VoodooHDA from here. I used the version 2.9.1 and patched the sound volume (attached below).
      - Download the WhateverGreen.kext from here. I used the version 1.2.9.
      - Download the AppleBacklightFixup.kext from here. I used the version 2018-1013.
      - Download the USBInjectAll.kext from here. I used the version 2018-1108.
      - Download the ACPIBatteryManager.kext from here. I used the version 2018-1005.
       
      - Download the VirtualSMC.kext from here. I used version 1.0.2. Replaced with FakeSMC of the HWSensors 3 r196 package.
      - Download the FakeSMC.kext from here. I used the version 2018-0915. Replaced with VirtualSMC.kext due 10.14.4 issues on update.
      - Download the AppleALC.kext from here. I used the version 1.3.4. Replaced with VoodooHDA.kext due mic not working.
       
       
      Wifi and Bluetooth (DW1560 / BCM94352Z)
       
      Unfortunately, some notebook manufacturers are currently blocking the replacement of wireless cards. They want you to only use the models sold by them. And of course, none of them from Lenovo for this notebook model is compatible with MacOS.
       
      If you try to start with an unauthorized wifi card for them, you will receive a screen error:
      1802: Unauthorized network card is plugged in - Power off and remove the network card. Since this check is done directly in the BIOS, the only solution is to modify it.
      But since nothing is easy in this life, there is one small big problem:
      - The BIOS update procedure does not allow you to use modded files as it used to be.
      - You will need to physically reach your BIOS on the motherboard and make use of a USB BIOS reader/writer.
       
      So what you need to do:
      1. Disassembly your laptop;
      2. Dump your BIOS with an USB BIOS reader with SOIC8 clip (to not desolder from the motherboard);
      3. Patch it (In addition to removing the whitelist, add the advanced menu);
      4. Fix RSA signature;
      5. Reflash BIOS;
      6. Replace wireless card;
      7. Remount your laptop;
      8. Done.
       
      Soon, I'll provide step by step in this process. Probably until end of this week.
      In the meantime, if you need to, send me your dump that I do steps 3 and 4 for you.
      I also add the Advanced Menu so you can increase to 128MB the DRAM-prealloc.
       
      To fix a Modded BIOS to remove the 5 beeps on boot, you need this guide: https://www.insanelymac.com/forum/topic/337333-guide-fix-insyde-h2o-bios-signature-5-beeps-on-lenovo (traduzido: pt-BR)
       
       
      After replaced the wireless card. Download those Kexts and put in /EFI/CLOVER/kexts/Other/
       
      - Download the AirportBrcmFixup.kext from here. I used the version 2.0.0.
      - Download the BrcmFirmwareRepo.kext and BrcmPatchRAM2.kext from here. I used the version 2018-0505.
      - Download the BT4LEContinuityFixup.kext from here. I used the version 1.1.2.
       
       
      Now you can start the instalation without problem (I guess).
       
       
      How install
       
      UEFI Setup Configuration and Installation

      UEFI configuration
       
      My BIOS is the latest: 1.93 (J4ET93WW) 

      - Shutdown and insert the flash drive.
      - Power on with F1 pressed to enter BIOS setup.
      - Change value: Config - Intel(R) AMT - Intel(R) AMT Control to DISABLED
      - Change value: Security - Security Chip to DISABLED
      - Change value: Security - Anti-Theft - Intel(R) AT Module Activation to DISABLED
      - Change value: Security - Anti-Theft - Computrace to DISABLED
      - Change value: Security - Secure Boot to DISABLED
      - Change value: Startup - UEFI/Legacy Boot to BOTH, Legacy First and CSM Support = Yes
      - Save & Exit Setup (F10)
       
      - Now, hold the F12
      - In the list, select your flash drive.
       
      The installer will start. 
      
      Format destination disk

      Format the disk with GUID partition mapping and name it "Macintosh".

      - Select Disk Utility in the list, then press Continue.
      - Click in View, then "Show All Devices".
      - Select the destination Disk, then Erase.
      - Name: HD, Format: APFS and Scheme: GUID Partition Map

      Close Disk Utility.
      
      Select "Install macOS", then Continue.
      Follow instructions in screen.

      After install

      After first part install the system will reboot. Maybe you have to press F12 again and select the flash drive.
      
      The second part of the installation will begin. This will take 16 minutes.
       

      Post installation

      Install bootloader
       
      When the second part of install finish, the system will reboot again.

      After performing the user initial setup and go to the desktop, you need to install Clover on internal disk.

      Open the Clover installer inside flash drive that you copied before.

      Use same options above but choose the system partition this time.

      Now you need to replace the EFI folder inside your destination disk EFI parittion, with EFI folder inside flash card EFI partition.

      If the flash drive EFI partition of your destination disk or flash drive is unmounted:
      Mount with terminal "sudo diskutil mount /dev/rdiskXs1". To know what X is, use "diskutil list", most likely is 0 for destination disk and 1 for flash drive.
       
      Then, eject the flash drive.
       
      Last step
       
      Move all Kexts from EFI partition to /Library/Extensions, with those commands in Terminal:
      sudo mv -R /Volumes/EFI/EFI/CLOVER/kexts/Other/* /Library/Extensions/ sudo chmod -R 755 /Library/Extensions sudo chown -R root:wheel /Library/Extensions sudo kextcache -i / Restart the system.
       
       
      It's done!
       
       
      Updates
       
      System update 10.14.3
       
      - Updated with success;
      - Everything works perfectly after reboot;
       

       
       
      System update 10.14.4
       
      - Updated Clover to 4910.
      - Updated Lilu.kext to 1.3.5 and WhateverGreen to 1.2.7.
      - After first reboot the update progress stoped with:
      GTrace synchronization point 4 Unsupported CPU Unsupported PCH hmm.. mismatch sizes: 3100 vs 20 It was still possible to start the previous installation, selecting "Macintosh" as opposed to "macOS Install" in Clover.
      So I created a flash drive with Clover 4910 and put only my config.xml, SSDT-L440.aml, the updated Lilu.kext and WhateverGreen.kext. And I decided to test VirtualSMC instead of FakeSMC.kext.
      With this I was able to install update 10.14.4. After installation I can boot normally, even with FakeSMC.kext that already in /Library/Extensions.
      I do not know what exactly happened, but now works everything like was previously.
       


       
       
      System update 10.14.5
       
      - Updated Clover to 4934.
      - Updated Lilu.kext to 1.3.6 and WhateverGreen to 1.2.9.
      - After first reboot the update progress stoped again (like 10.14.4 update) with:
      GTrace synchronization point 4 Unsupported CPU Unsupported PCH hmm.. mismatch sizes: 3100 vs 20 It was still possible to start the previous installation, selecting "Macintosh" as opposed to "macOS Install" in Clover.
      I decided to rollback to FakeSMC.kext but this time with the version of HWSensors 3. Link above.
      With this I was able to install update 10.14.5. After installation I can boot normally.
       

       
       

      And last but not least
       
      I would like to thank the following community members, by making these dream possible:
      @crushers, @snatch, @apianti, @blackosx, @blusseau, @dmazar, @slice2009, @autumnrain, @phpdev32, @EMlyDinEsH, @RehabMan, @Scellow, @mitch_de, @Shailua, @Andy Vandijck, @maxfierke, @ArturXXX, @LexHimself, @brumas, @Shiki and all others members involved directly or indirectly.
       
       
       
       
       
       
      32MB_DRAM-prealloc_config.plist.zip
      128MB_DRAM-prealloc_config.plist.zip
      SSDT-L440.aml
      VoodooHDA.kext.zip
      AppleHDADisabler.kext.zip
    • By kushwavez
      Hi!
       
      I have everything working on my Acer notebook, except FN + Brightness keys using VoodoPS2Controller.kext
       
      Now the brightness keys are "Pause+Break = Brightness Up" and "Fn+F12 = Brightness Down" working right now but they are not the actual keys. 
      The actual brightness keys are "Fn+RightArrow = Brightness Up" and "Fn+LeftArrow = Brightness Down" but they are not working.
      The problem is I don't know the codes.
      Installed ioio and enabled debugging to console:
      Pause/Break is generating: "ApplePS2Keyboard: sending key e045=71" which upper the brightness
      Fn+F12 is generating: "ApplePS2Keyboard: sending key 46=6b" which lower the brightness
      Fn+RightArrow/LeftArrow generates nothing.
      Keyboard attached to PS2K
      Then I used rehabman's guide to enable ACPIDebugging, Installed kext to L/E, Debug methods (Instrument EC Queries, Add DSDT Debug Methods) to DSDT, but there are no codes generated to the log.
       
      Attaching debug folder.
      Also I don't know if it will help, but on Linux I got a code from decreasing/rising brightness with Fn+Left/RightArrow keys:
      Fn+RightArrow: "0xe0 0x54 0xe0 0xd4"
      Fn+Left: "0xe0 0x4c 0xe0 0xcc"
       
      Also I love using EMlyDinEsH's SmartTouchpad Driver, with that all of my Fn keys are working except Brigtness keys ofc. If there are any fix I would like to use that with the smarttouchpad driver. 
      EMlyDinEsH's SmartTouchpad Driver: https://osxlatitude.com/forums/topic/1948-elan-focaltech-and-synaptics-smart-touchpad-driver-mac-os-x/
       
      Specs in my signature. 
      Please help me fix this very last issue on my acer.
       
      debug_4751.zip
    • By Angelo_
      Hi, I followed the rehabman guide (linked in the vanilla guide on the side of r/Hackintosh, not sure if I can link it) for laptops for my yoga 730ILW13 with an 8265u, Conexant 11870, 8gb of ram, 13.3" fhd and I found that upon booting the installer usb I get this weird issue where the screen displays what it should but the screen is incredibly dim (though it was off before using a flashlight on it) and it flashes every few seconds for a few milliseconds to the correct brightness, I used the plist for hd615-650 (including my 620), not quite sure what could be the culprit, first time hackintoshing a laptop so it might be a stupid brightness kext I forgot but didn't find any in that post or in this forum :c 
      Attached the clover zip so that anyone with more experience than me might give an idea in what could be a way to fix this.
      Thank you in advance 
       
       
       
      CLOVER.zip
    • By SepehrM
      I'm trying to install High Sierra 10.13.3 on an ASUS N552VW laptop, and I get stuck after this message:
      "could not recover SATA HDD after 5 attempts, terminating" 
      And some other warnings afterwards.
      Specs:
      CPU: Intel Skylake 6700HQ 2.6GHz
      RAM: 16GB DDR4
      2TB HDD + 128GB SSD
      GPU: Intel HD Graphics 530 + Nvidia GTX960m
      I'm installing using a 16GB USB3 flash drive on one of HDD volumes (UEFI Mode)
       
      I uploaded the verbose log and clover config.plist
      config-new.plist

    • By Leinad12
      Olá a todos.
      Estou com o macOS Mojave instalado num Lenovo 305 (com um i3 5005 e uma HD 5500) porém tou com um problema.
      Sempre que o computador entra em pausa (Sleep) não consigo voltar a "acordar" (Wake).
      Alguém pode me ajudar pf?
×