Jump to content
MacPeet

[Guide] macOS Sierra 10.12 - Dell Optiplex 780 (760) (755) (790) (990)

1,542 posts in this topic

Recommended Posts

Yes, the EVGA Geforce 210 works with Sierra and full graphics acceleration in my Esprimo.

My HD5450 in Dell since DP1 works without problems.

Share this post


Link to post
Share on other sites
Advertisement

Has anyone tried running Sierra with CPU without SSE4.1 support?

My Optiplex is at my friend's house at the moment.

 

 

Sent from my iPhone using Tapatalk

Share this post


Link to post
Share on other sites

Yes, without SSE4 support it does not work.

 

Update:

macOS Sierra 10.12.1 Beta 1 (16B2327e) works without problems

Works without SSE4? What do you mean? At which machine works? With which cpu?

Share this post


Link to post
Share on other sites

Yes, without SSE4 support it does not work.

Ok, had to check if someone personally have tried because of this post from Pike:

"What I found in the kernel is the old fpu switch for SSE/SSE2 but the string SSE4(.1/2) is not used anywhere in the kernel. The SSE4.2 CRC32 instruction is also not used in the kernel so it may actually not be that bad for old hardware after all."

Share this post


Link to post
Share on other sites

I may try this out on my Optiplex 755 to see if 10.12 works if not then 10.11.6 will be the end of the road for the 755.

Naah, for a few bucks just buy a E8400 or E8600 (both have SSE4.1 instruction set) put it in a 755 and go with macOS Sierra! :

Share this post


Link to post
Share on other sites

Ok, had to check if someone personally have tried because of this post from Pike:

"What I found in the kernel is the old fpu switch for SSE/SSE2 but the string SSE4(.1/2) is not used anywhere in the kernel. The SSE4.2 CRC32 instruction is also not used in the kernel so it may actually not be that bad for old hardware after all."

What exactly system do you have? If you have success please make an new thread or pm me. Thanks. 

 

Last night i tried to install Stable version of Sierra with Clover 3659 and 3761 at my Optiplex 760 and i had no success. Beta was installed , stable it was impossible. Maybe it is Clover, or maybe it is fake smc kext who need update. 

Any ideas?

Did someone tried the first stable with success?

Share this post


Link to post
Share on other sites

@owbp I actually have the q9650 in this hackintosh already which has sse4.1 instruction set. So hopefully I shouldn't have an issue to put Sierra on this machine. 

Share this post


Link to post
Share on other sites

@Theoprofil

my Clover is 3650 and works with:

macOS Sierra GM (16A322) and (16A323) and 10.12.1 Beta 1 (16B2327e)

my FakeSMC is 6.21.1412

Share this post


Link to post
Share on other sites

Hi, thanks for great guide, but I'm getting no sound.

Optiplex 760 E8400

I installed your kext and added the kext to patch in Cloverconfig, do I have to do the DSDT Code insert or is it just optional?

 

Error.rtf

Share this post


Link to post
Share on other sites

It now just shows HDMI sound  :(  I installed the AppleHDA to S/L/E, do I have to do something in clover despite Identity 1? 

Got it to work! :thumbsup_anim:  Thanks for your work!

Share this post


Link to post
Share on other sites

The alternative:

 
I use on my Dell Optiplex already AppleALC method:
 
AppleALC_1.0.14.RELEASE.zip or later (LayoutID 11 for Dell Optiplex 780/760)
 
1. Install back the original AppleHDA to S/L/E
2. Install the AppleALC to S/L/E
3. Delete all AppleHDA Kext-to-patch entries in Clover
4. delete realtekALC.kext of Clovers kext folder
5. add bootflag -alcbeta
post-1358580-0-93495800-1474794523_thumb.png
6. Change LayoutID of 1 to 11 (DSDT HDEF 0B)
7. rebuild cache and reboot
 
Edit:
With AppleALC 1.0.16.Release and macOS-Final the bootflag -alcbeta is no longer necessary.

Share this post


Link to post
Share on other sites

I have been patiently waiting for this Guide to be Updated to the stable Sierra released on 20 September.

​When will it be updated?

​Step 2 will be different path.

Step 6 assumes we have El Capitan "kexts", what if it is a fresh install with no prior installation of El Capitan?

​How do I install if I have no access to a mac to begin with?

Share this post


Link to post
Share on other sites

@runo, I'm sure MacPeet will polsh the guide as soon as he grabs some time for it.

In the meantime, don't be so lazy :P

Step 2 - createinstallmedia is here since Mavericks and the guideline is

createinstallmedia --volume volumepath --applicationpath installerpath

So in this case it is

sudo /Applications/Install\ macOS\ Sierra.app/Contents/Resources/createinstallmedia --volume /Volumes/Untitled --applicationpath /Applications/Install\ macOS\ Sierra.app

If we assume that you erased your USB without any change in Disk Utility, so the name of it is Untitled.

If you don't want Terminal to ask you if you would like to erase your USB named Untitled, than you add -nointeraction at the end of the line.

 

Step 6. All you need is in the .zip file at the end of this first post.

Lastly, you can make OS X Install USB from Windows and Linux, which ever you prefer, just search the forum for the guides.

Share this post


Link to post
Share on other sites

Hi  :D 

Please help me, I just installed macOS Sierra on HP Compaq DC7900 CMT but usb mouse and any usb drive I inserted not working, I don't know how but I think the usb hub is the problem please help me  :( .

Share this post


Link to post
Share on other sites

Lastly, you can make OS X Install USB from Windows and Linux, which ever you prefer, just search the forum for the guides.

 

I searched for this and found no success. There is a Install USB from Windows utility made by chris1111 but he closed the thread and deleted all download links! And another utility BDutility.exe tries to download some strange recovery file instead of using the "Install macOS Sierra.app" file I downloaded from torrent website. And the virtualbox way I dont know what mac ISO is safe and virus-free to use. With Transmac.exe utility I cant use the .app file, it requires a .dmg file I dont have.

Is this site for Sierra download trustworthy? http://www.mac-torrent-download.net/application/utility/macos-sierra-10-12-16a323-installer/

I am confused. I thought mac is supposed to be user friendly. Please help me. I have both Windows and Linux, no Mac yet.

Share this post


Link to post
Share on other sites

 Macs and OS X are very user friendly, but you  have to remember that we're not dealing with Macs here, we're building hackintosh machines (doing something that isn't meant to be done). :)

 

Here's tutorial for Windows (post number 18): http://www.insanelymac.com/forum/topic/288795-guide-creating-os-x-usb-installer-using-a-windows-pc-only/?p=2012539

and here is for Linux: http://www.insanelymac.com/forum/topic/293168-guide-how-to-make-a-bootable-os-x-109-mavericks-usb-install-drive-on-linux/

 

P.S. I too didn't have Mac or Hack at the time of my first hackintosh attempt, so i have built installer from Linux. I was using Mountain Lion, but it worked.

 

Edit:

One more thing i see you're having trouble with - OS X apps are mostly standalone packages, so you have to look at them almost like Windows folders... Sort of...

So dmg file (image file) is located in Install Mac OS X "what ever".app/Contents/Shared Support/InstallESD.dmg

That is what you're looking for here.

Share this post


Link to post
Share on other sites

Here's tutorial for Windows (post number 18): http://www.insanelymac.com/forum/topic/288795-guide-creating-os-x-usb-installer-using-a-windows-pc-only/?p=2012539

and here is for Linux: http://www.insanelymac.com/forum/topic/293168-guide-how-to-make-a-bootable-os-x-109-mavericks-usb-install-drive-on-linux/

 Mac OS X "what ever".app/Contents/Shared Support/InstallESD.dmg

That is what you're looking for here.

 

Thanks! Those links are for installing Mavericks, do they work for Sierra too?

And steps 3 and 9 for Optiplex talk on installing Clover to the hard drive, without saying how, how to do that? What on earth is DP1/2/3, when I downloaded Clover from sourceforge it has no DP on it.

Do I install the Clover after or before installing Sierra using a bootable USB when I have successfully made one?

I tried extracting the InstallESD.dmg using linux and it had error during extracting, I think I need to try it using 7zip or something.

Share this post


Link to post
Share on other sites

Naah, for a few bucks just buy a E8400 or E8600 (both have SSE4.1 instruction set) put it in a 755 and go with macOS Sierra! :

 

Works on my 755 with an E7300 ;)  E7600 has the highest multiplier (11.5) if you want to do the BSEL mod from 1066 to 1333 fsb for approx 3.8ghz (I don't think 755's can do 1600 fsb).

Share this post


Link to post
Share on other sites

@runo

I don't think they will work in Sierra - Linux one doesn't work for Yosemite and up and i have never tried Windows method.

 

You should forget about this topic, for now, and get your Optiplex up and running with something older that you have links for Win/Linux installation.

After that, Sierra will be breeze, because you will have working Mac so to speak.

 

DP i short for Developer Preview and it has nothing to do with Clover, it's version of Mac OS before it reaches GM (Gold Master) a.k.a Final Release.

Why MacPeet is mentioning that is that older Clover versions can't boot newer OS's.

 

You can use your bootable USB after installation to boot your hackintosh (because you'll have boot files already on USB, Clover or Chameleon).

 

In Linux you will use 7zip for all your extractions, so i don't really know what you mean by that? Just be sure to install "p7zip-full" from terminal or synaptic package manager (whatever you're using).

 

We're really going OFF topic here, so it would be best to open topic about your problem or give it a good read and install Mountain Lion or Mavericks on your Optiplex, so you could work with Sierra and ask for help  in here.

 

 

Works on my 755 with an E7300 ;)  E7600 has the highest multiplier (11.5) if you want to do the BSEL mod from 1066 to 1333 fsb for approx 3.8ghz (I don't think 755's can do 1600 fsb).

For the moment i fainted here! :)

E7300 still has the SSE4.1 instruction set, so no surprises there. Yes, AFAIK, 1333fsb is max for 755.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By plasticworld
      After a long run, I successfully upgraded High Sierra to mojave 10.14 on an intel 5 series chipset MotherBoard.
       
      MotherBoard: H55ms2
      RAM: 6GB
      GPU1: Saphire AMD RX 460
      GPU2: Nvidia 8400GS
      Storage: 500 GB HDD WD Green.
       
      The requirement:
      1) macOS pre mojave.
      2) macOS mojave installer from Apple store.
      3) Empty partition or USB to upgrade from.
      4) Un-mout all unused dmgs.
      5) GPT/GUID HDD.
       
      HOWOT:
      1) Prepare an empty partition or USB with at least 6 GB.
      2) Format the partition or USB with GUID partition table and HFS+ partition with a name BootablePartition.
      3) Go to /Application/Install macOS Mojave.app.
      4) Show Package Contents.
      5) Go to Contents/SharedSupport you will find BaseSystem.dmg.
      6) Double click on BaseSystem.dmg to mount.
      7) From Disk Utilty click on your partition or the USB that you prepared from number (2).
      8) Click on restore, and chose OS X Base System (BaseSystem.dmg image), then restore it to that partition or USB.
      9) After restoring rename the partition back to BootablePartition.
      9) Run this command:
      rm -rfv /Volumes/BootablePartition/System/Installation/Packages 10) Create a new folder instead of the broken link and name it Packages, run this command:
      mkdir -v /Volumes/BootablePartition/System/Installation/Packages 11) Go back to /Application/Install macOS Mojave.app and repeat number 2.
      12) Go to Contents/SharedSupport you will find InstallESD.dmg.
      13) Mount InstallESD.dmg.
      14) Run this command:
      cp -v /Volumes/InstallESD/Packages/OSInstall.mpkg /Volumes/BootablePartition/System/Installation/Packages/ 15) Download the latest clover from https://sourceforge.net/projects/cloverefiboot/
      16) Install clover on your USB BootablePartition or in a different USB to boot from it. delete all your CLOVER/kext/10.xx and keep others, make sure you don't have any extra kext rather than FakeSMC.kext in the other folder.
      in my case I used FakeSMC.kext and my lan kext RealtekRTL8111.kext.
      17) known Problems in my build: 
      If I updated directly from the apple store the installer in clover will boot with a cross circle sign.
      The FIX is to add this to Clover KextToPatch Thanks to @sunKi http://www.insanelymac.com/forum/topic/327488-macos-high-sierra-final-release-is-out-17a365/page-10?do=findComment&comment=2505086 this fix is still working for me in mojave.
      <key>KextsToPatch</key> <array> <dict> <key>Comment</key> <string>fix IO error ICH10 for 10.13, credit SunKi</string> <key>Disabled</key> <false/> <key>Find</key> <data> RYX2D5XCiciD4P5mhcl4D4TSdQs= </data> <key>Name</key> <string>AppleAHCIPort</string> <key>Replace</key> <data> iciD4P5mhckPmMFBCMyQkJCQdQs= </data> </dict> <dict> <key>Comment</key> <string>fix hotplug ICH10 for 10.13, credit SunKi</string> <key>Disabled</key> <false/> <key>Find</key> <data> icglQGACAD1AIAAAdQyB4b9///+Ji1EBAAA= </data> <key>Name</key> <string>AppleAHCIPort</string> <key>Replace</key> <data> kJCQkJCQkJCQkJCQkJCQkJCQkJCQkJCQkJA= </data> </dict> <dict> <key>Comment</key> <string>External icons patch</string> <key>Disabled</key> <false/> <key>Find</key> <data> RXh0ZXJuYWw= </data> <key>Name</key> <string>AppleAHCIPort</string> <key>Replace</key> <data> SW50ZXJuYWw= </data> </dict> </array> 18) make sure you have apfs.efi copy it from /Volumes/BootablePartition/usr/standalone/i386/apfs.efi to your EFI/CLOVER/drivers64/ and EFI/CLOVER/drivers64UEFI/.
      19) SMBIOS mac model that I use is iMac13,2.
      20) Go to /Application/Install macOS Mojave.app click on it and chose to install to your macOS Mojave partition.
      21) Reboot.
      22) From clover chose BootablePartion.
      23) If everything is okie BootablePartition will boot to install macOS mojave, wait wait wait till it finish it might take to 1 hour just wait it will reach the auto reboot soon .
      24) Boot to your old macOS Hight Sierra that will be your mojave partition now and enjoy.
       
      POST Install:
      1) audio: 
      a) Download Lilu.kext and AppleALC.kext or build them from source (which I did).
      b) place them in your /EFI/CLOVER/kext/others/
      c) add your audio layout in clover/Devices dict options in my case it's ALC888B which has the layout of 1:
      <key>Audio</key> <dict> <key>Inject</key> <string>1</string> </dict> d) I had to add beta args to clover/Boot dict, argument (-lilubeta -alcbeta):
       
      <key>Arguments</key> <string>-lilubeta -alcbeta</string> 2) Add number 14 KextsToPath array to your clover as well.

      Anything else is working for me I didn't need any extra clover kext so far, I tried whatevergreen.kext to fire up my rx 460 without the helper card but no success, So I am just sticking with booting from Nvidia as a first GPU from my motherboard configuration then swap the cables after choosing my macOS partion from clover.
       
      After upgrading my HFS+ High Sierra partition converted to APFS, no know problem so far.

      Happy build and more info about the partitioning method with a more detailed instructions in this post that I used to update my Sierra to High Sierra
       
      Special thanks to crazybirdy, sunKi and all of you out there that make this happens.
    • By NoEnd
      Hi team,
       
      I have tried to update to security update 2019-001 multiple time with no luck, today I've booted the update with -verbose and attached videos shows the details.
       
      Appreciate your help
       
      Thanks
      Untitled.mov
    • By JhonneR
      Good morning, everyone, I'm sorry if I was wrong in choosing the topic but I need help.
      I have found it extremely difficult to mount a Hackintosh in my acer.
      Setup;
      I5 2430m 2.4 6GB RAM
      Mobo P5we0 - Intel intel Graphics 3000
      At the moment I have not found out what my audio codecs are.
      but I'll leave the link on the motherboard.
      however, my real problem is several.
      I have already used the itakos image, I have already used several images that could be installed normally and that after installing the image I do not have internet via cable or wireless.
      And another, I already looked in other forums and I know that I will be called a donkey in the logical question but I have not been able to install the [url=&quot;http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/&quot;]#####[/url] or clover to start from the Hard Disk, so I do not know what to do.At the moment I still do not know if there has already been someone who has already installed the High Sierra or just the Sierra in this notebook model and obtained permanent success.
      If anyone can help me, I'll be grateful.
      Installations without success, but with the system already installed in ACER;
      SIERRA
      HIGH SIERRA
      MOJAVE
      All with the same symptom. Starting only by the bootable USB stick and without internet connection via cable and wireless.
      Appreciate ! Acer 5750 Official Page
    • By gengik84
      Ciro82==>>Thanks
      Uno dei tre Requisiti:
      Hack funzionante Mac vero Macchina virtuale Impostazioni Bios per il boot:
      Cercate una voce  del tipo “Sata Mode”e settatela  in AHCI
      Secure Boot: disabilitare o altri sistemi operativi
      CSM: UEFI o LEGACY, oppure a secondo del tipo di installazione
      VT-x / VT-d disable
      *Nota: Secure boot e csm valido solo per bios UEFI
      Materiale Occorrente 
      "OS X (Versione App.Store)”
      USB 8GB  *nota: nel caso di usb superiori dovrà essere partizionata, in modo da avere una partizione su cui "lavoreremo,di questa dimensione
      ShowAllfiles 
      kext Wizard 
      Bootloader Clover_2.3k_r xxx:                   http: //sourceforge.n.../cloverefiboot/
      Clover Configurator:                                    http: //mackie100proj...a.org/download/
      FakeSmc.kext:                                            https://github.com/kozlek/HWSensors/releases
      In allegato,a fondo pagina troverete un "pacchetto" contenente : ShowAllfiles, Kext Wizard, FakeSmc.kext: 
      App alternative:
      ESP Mounter Pro: per montare la partizione EFI
      Vi illustrerò tre metodi per creare la usb, ma sono ben distinti… quindi usatene soltanto uno
      Metodo 1: “Install Mac_OS_X.command” Metodo 2: “Create Install Media di Apple” Metodo 3:  Metodo Manuale Alla fine delle preparazione dell’installer, tutti i metodi necessitano l’installazione del Bootloader Clover sulla a vostra USB.
      “CONDIZIONI OBBLIGATORIE”
      PUNTO 1: che la vostra usb sia stata preventivamente nominata USB (caratteri maiuscoli) Tabella di partizione GUID e la formattazione in  Mac esteso Journaled.
      PUNTO 2: che l’installer di OSX si trovi in Applicazioni
      Utility Disco 
      Selezionate la pendrive, andate su “partizione”, selezionate “1 partizione”, impostate Mac OS esteso journaled e date il nome USB, poi in basso cliccate su opzioni e scegliete Tabella partizione (GUID), poi “applica”.
      Immagine 
      Riporto nuovamente l’operazione sopra citata adoperando dal nuovo Utility Disco introdotto su El Capitan.
      Rimane ovviamente invariato nome della usb in ==>> USB (maiuscolo), la formattazione in Mac esteso Journaled e sia la mappa partizione in GUID
      Da utility disco selezionate la usb, cliccate su inizializza.
      dal menù a tendina scegliete la relative impostazioni
      Immagine  
      Procedura effettua da High Sierra è la stessa della precedente, l'unica attenzione e operazione da aggiungere in primis  è cliccare nel menù a tendina in alto sulla sinistra di utility disco e selezionare "mostra tutti i dispositivi"
      Immagine 
       
      =====================
        METODO 1: "Install_Mac_OS_X.Command" Lo script che trovate allegato in fondo alla guida permette la creazione dell’installer in maniera automatica
      Include la possibilità di scelta di tre versioni di osx
      Yosemite El Capitan Sierra Il risultato finale è come quello del metodo "manuale" descritto nella guida, per cui l'installazione avverrà in un solo passaggio, non in due come con il metodo createinstallmedia. 
      Offre inoltre la possibilità di inserire un kernel patchato, utile, per esempio, per chi usa AMD.
      Rimane invariato il nome dato alla usb in USB, mappa partizione e tipo di formattazione
      Se la vostra usb non sarà rinominata nel modo corretto, verrete avvisati dal terminale, quindi non dovrete far altro che apportare la relativa modifica e rilanciare nuovamente lo script
      Esempio
      ===========================
      Metodo 2 
      L'intento è quello di usare la procedura fornitaci direttamente da Apple, "createinstallmedia", introdotta  con Mavericks. 
      Tale metodo prevede l’uso del terminale che via via se ne sta perdendo il “valore e l’uso”
      Inizialmente per i neofiti potrà sembrare problematico ma alla fine non è così.
      Durante il post installazione alcune operazioni ne richiedono l’ uso.
      Perciò mi sono chiesto perchè, qualora uno volesse, non far conoscere da subito un po’ questo “strumento”???
      Per favorirvi vi ho allegato i comandi già  “pronti”, i quali li potrete copiare ed incollare sul terminale.
      A questo punto aprite il terminale, copiate ed incollate il comando sottostante e premete invio, digitate la vostra password e premete nuovamente invio.
      Comando per creare USB con Yosemite:
      sudo /Applications/Install\ OS\ X\ Yosemite.app/Contents/Resources/createinstallmedia --volume /Volumes/USB --applicationpath /Applications/Install\ OS\ X\ Yosemite.app --nointeraction  
      Comando per creare USB con El Capitan
      sudo /Applications/Install\ OS\ X\ El\ Capitan.app/Contents/Resources/createinstallmedia --volume /Volumes/USB --applicationpath /Applications/Install\ OS\ X\ El\ Capitan.app --nointeraction Comando per creare USB con Sierra 
      sudo /Applications/Install\ macOS\ Sierra.app/Contents/Resources/createinstallmedia --volume /Volumes/USB --applicationpath /Applications/Install\ macOS\ Sierra.app/ --nointeraction Per creare USB con Hight Sierra o Mojave usate --> C_I_M (aggiornato per 10.14)
       
      Funziona con il drag & drop sul terminale, in questo caso non vi è necessità che la usb sia nominata in un determinato modo ed essendo basato su create install media ovviamente funziona da 10.9 a 10.14.... 
      BENE…IL PROCESSO DI CREAZIONE E’ INIZIATO…
      AVREMO CIRCA 20/30 MINUTI DI TEMPO LIBERO A CUI DEDICARSI A CIO’ CHE VOGLIAMO………………………………………..  
      COLGO L’OCCASIONE PER FARVI NOTARE LA VELOCITA’ E LA SICUREZZA DI QUESTO METODO
      CONFRONTATE QUESTO CON IL TERZO METODO E NOTERETE CHE CON UN SOLO PASSAGGIO, OSSIA IL COMANDO DATO AL TERMINALE, FACCIAMO IN UNA SINGOLA OPERAZIONE TUTTI I VARI STEP DESCRITTI SULL’ ALTRO METODO.
      DETTO QUESTO, MOLTO IMPORTANTE E’ SOTTOLINEARE CHE COSI’ FACENDO EVITEREMO ERRORI  DI DISTRAZIONE RIGUARDO AI PASSAGGI O FRAINTENDIMENTI.
      Immagine 
      Potete adesso passare ad installare il bootloader Clover sulla vostra usb.
      *NOTA*:
      Avendo usato questo metodo l'installazione si dividerà in due fasi, perciò dopo il primo riavvio e necessario far partire nuovamente l'installer, selezionare lo stesso disco senza formattarlo.
      Finita questa ulteriore fase , l'installazione sarà terminata
      =========================
      METODO "MANUALE"....  (lascio per futura memoria-Compatibile fino a 10.12)
      ==========================
      Bootloader
      **Nota:** Installazione in UEFI  dipenderà dalla scheda madre in vostro possesso, quindi se non supporta tale opzione , il bootloader dovrà essere installato in  modalità Legacy.
       Vi invito, qualora non sapeste questa informazione, a recarvi nel sito ufficiale del produttore e controllare le informazioni a riguardo
      Fatto questo dobbiamo installare  Clover sulla usb.
      A seconda del tipo di Bios o al tipo di installazione che vogliamo fare UEFI o Legacy avremo ovviamente configurazioni diverse in questa fase.
      Lanciate il pkg.
      Immagine 

       
      Cambiate la destinazione di installazione ad USB oppure Install Mac_OS_X (a secondo del tipo di creazione eseguita)
      Successivamente clicchiamo su "Ad Hoc"
      Per Installazione UEFI
      Mettete i flag   : Installazione solo per avvio UEFI
                               : installare Clover nella ESP
                               : Driver64UEFI  AptioMemory --> (consigliato) 
                               : Driver64UEFI  ApfsDriverLoader --> (consigliato) --> sostituisce l'uso del driver apfs.efi
                               : Selezionate l'altri driver come da successiva immagine,
       
      *Nota: Altri driver che si possono usare  al suo posto  sono:
       informazioni 
       
      Proseguite con l’installazione.
      Immagine 
      ** Ricordate che avrete accesso a questa cartella dopo aver montato la partizione EFI**
      ===========================
      Per installazione Legacy
      Immagine 
      ===========================
      Impostazione per config.plist:
      Con clover configurator “montate” la partizione EFI della usb.
      1) Per fare questo nel menù di sinistra, cliccate su “Mount EFI”
      2) individuate la partizione relativa alla vostra usb, a questo punto montiamo la relativa partizione EFI  selezionando l’apposito pulsante “Mount Partition”
      Immagine 
      3) Successivamente cliccate su “Open Partition”.. recatevi in EFI/Clover ed aprite il config.plist
      4) Sezione ACPI: Disabilitate tutti i fix sia del menù 1 che del menù 2
      Immagine 
      5) Sezione BOOT: Sole se si sta installando Yosemite mettete il flag su kext-dev-mode=1
      Immagine 
      6) Sezione RT Variables: Se si sta installando El Capitan oppure Sierra, aggiungere i valori: BooterConfig= 0x28, CsrActiveConfig= 0x67
      Immagine 
      7) Sezione System Parameters: Su inject kext mettete YES
      Immagine 
      ===========================
      Nota: Su El Capitan, è stato introdotto SIP (System Integrity Protection)
      Info:
      ===========================
      Recatevi in EFI/Clover/kext/10.x 
      X= alla versione di osx che state installando. Per esempio se installerete Yosemite dovrete recarvi nella cartella 10.10, con El Capitan in 10.11….ecc
      Se non ci fosse tale cartella, createla e nominatela voi a “modo”.
      Copiatevi all’interno FakeSmc.kext
      *Nota se venite già da altre vostre configurazioni, oltre kext sopra citato ,potete mettere gli altri necessari per il vostro hardware
      Stessa cosa se avete DSDT e/o SSDT potete copiarli in EFI/Clover/Acpi/Patched
      Immagine 
      
      Per High Sierra:
      Scaricare il driver apfs.efi a fine guida, collocarlo:
          --> EFI/clover/Driver64UEFI se stiamo usando UEFI
      --> EFI/Clover/Driver64 se stiamo usando Legacy
       
      Per chi volesse continuare ad usare HFS vi rimando a questo post:
        Come installare High Sierra in HFS direttamente dalla usb  
      Utenti Laptop:  Nel 99% è obbligatorio disattivare la grafica discreta Nvidia/Amd per installare questo nuovo osx
                                     Quindi aggiungete --> SSDT-Disable_DGPU.aml.zip
                                     in EFI/Clover/acpi/Patched della usb
      --------------------------------------------------------------------
      Per Mojave:
      Scaricare il driver apfs.efi per 10.14 a fine guida, collocarlo:
          --> EFI/clover/Driver64UEFI se stiamo usando UEFI
      --> EFI/Clover/Driver64 se stiamo usando Legacy
      Versione di clover non antecedente a V_4015
      Volete usare HFS?
      E' possibile fare un installazione diretta su altro disco o partizione, nel caso può essere usato anche per effettuare aggiornamenti...
      nel caso guardate...
       Mojave in HFS 
       Oppure direttamente da usb  
       
      Fatto questo avrete la vostra USB bootable per installare OSX.
      ………Non scordatevi Fakesmc.kext da mettere nella relativa cartella…. senza il quale non farete mai il Boot......
      *NOTA: se usato il terminale per la creazione della usb, l'installazione si dividerà in due fasi, perciò dopo il primo riavvio e necessario far partire nuovamente l'installer, selezionare lo stesso disco senza formattarlo.
      Finita questa ulteriore fase , l'installazione sarà terminata
      **NOTA** Se avete processori Broadwell,Skylake o Kabylake...usate FakeSmc.kext e relativi sensors che trovate all'interno del secondo pacchetto.. (potete usarlo anche sui precedenti senza problemi, essendo una versione più aggiornata ha ulteriore supporto per le cpu più recenti)
      Update: Fakesmc e sensors versione 6.26
      Post installazione... post #2           
       Buon Hack….. 
      Aggiornamento:Install_Mac_OS_X.command.zip (compatibile da 10.10 a 10.12)
      le info le trovate a questo post
      Ringrazio @Ciro82 che mi ha aiutato nel preparare questa guida.
      Pacchetto.zip
      Pacchetto-2.zip
      apfs.efi-10.13-NoLog.zip
      Pacchetto-Fake+Sensors 6.26.1440.zip
      apfs.efi-10.13.1-No_LOG.zip
      apfs.efi-10.13.2_No_Log.zip
      apfs.efi-10.13.3-No_Log.zip
      apfs.efi-10.13.4-No_Log.zip
      apfs.efi-10.13.5_No_Log.zip
      C_I_M.zip
       
      apfs.efi-10.14-beta1_No_Log.zip





       

×