Jump to content
maltex

HELP! After installtion of Yosemite 10.10.5

14 posts in this topic

Recommended Posts

After installtion of Yosemite 10.10.5 on my AMD PC , the system runs smooth and perfect, with the latest kernel 10.10.5_SSEPlus_V3, but i have following issues, which needs your help to be fixed.

 

Sorry, i am bloody new in this sector.

 

1. how can i boot from HDD instead of USB Stick? Enoch is currently installed on USB

2. which bootlader can be installed also? Best one? Enoch, etc... ?

2. how to insert bootflag into bootloader to start automaticlly with these flags, instead of entering flags every boot?

3. Sound is not working -- any kext or etc...? --> Realtek

4. no network -- any kext or etc...? --> 100 mbit/s Realtek

 

My System:

 

AMD Phenom II X6 T1090

ASRock Mainboard

8GB RAM

Nvidia GTX560

WD 500GB

Share this post


Link to post
Share on other sites
Advertisement
to 1)

Use the current Enoch bootloader, see here: http://www.insanelymac.com/forum/files/file/71-enoch/

install the bootloader on your OS X HDD

 

to 2)

in the folder /Extra/ is the org.chameleon.boot.plist, open this file with textEdit or plist Editor, change the line in the field:

 

for Example:

 


Kernel Flags

-v kext-dev-mode=1 npci=0x2000 GraphicsEnabler=No usekernelcache=No

 


and paste this line in to org.chameleon.boot.plist:


 

EthernetBuiltIn

Yes

 


Moreover, reading, how to configure the org.chamleon.boot.plist.

 

Furthermore, install these Ethernet kext driver of Mieze: http://www.insanelymac.com/forum/files/file/88-realtekrtl8111-binary/

 

then Fix the permission and renew the Cache with kext wizard and start the system again and boot from your OS X HDD

 


Edit:

both bootloader work very well.

If everything starts properly and you have enough experience with OS X etc..., then you can try to install with Clover bootloader. But install first on a USB flash disk, test and if everything is OK, then you can install clover with all modifications on your HDD 

 

Share this post


Link to post
Share on other sites

 

to 1)
Use the current Enoch bootloader, see here: http://www.insanelymac.com/forum/files/file/71-enoch/
install the bootloader on your OS X HDD
 
to 2)
in the folder /Extra/ is the org.chameleon.boot.plist, open this file with textEdit or plist Editor, change the line in the field:
 
for Example:
 
<key>Kernel Flags</key>
<string>-v kext-dev-mode=1 npci=0x2000 GraphicsEnabler=No usekernelcache=No</string>
 
and paste this line in to org.chameleon.boot.plist:
 
<key>EthernetBuiltIn</key>
<string>Yes</string>
 
Moreover, reading, how to configure the org.chamleon.boot.plist.
 
Furthermore, install these Ethernet kext driver of Mieze: http://www.insanelymac.com/forum/files/file/88-realtekrtl8111-binary/
 
then Fix the permission and renew the Cache with kext wizard and start the system again and boot from your OS X HDD
 
Edit:
both bootloader work very well.
If everything starts properly and you have enough experience with OS X etc..., then you can try to install with Clover bootloader. But install first on a USB flash disk, test and if everything is OK, then you can install clover with all modifications on your HDD 
 

 

Hi, and thanks for your quick response. I'll try this. Might it also possible to use Chameleon Bootloader instead of Enoch?

Share this post


Link to post
Share on other sites

After install 10.10.5, i want to install the latest update, security, itunes etc..., after installation, reboot got a loopboot, what do i have to do? Before and after, please help me quickly, thanks

Sound is only hearing crizzeling due headphone, not through screen speaker by hdmi, any ideas? Kext? network is working fine

 

Gesendet von meinem LG-D802 mit Tapatalk

Share this post


Link to post
Share on other sites
Start your system again, and make a picture of the situation and upload it here.

Share this post


Link to post
Share on other sites

Start your system again, and make a picture of the situation and upload it here.

Only receive a reboot after whitescreen comes up for a second, thats it.

Is there no workaround to install 2016 - 003 update? Itunes, Safari, Remote Desktop Client are installed, only the update makes problems after install.

 

By the Way, do you have a audio kext, which worked? And maybe a cpu identifier? HDD icons are yellow,orange like external HDD. All other things are running well.

 

2d8c94523c81e62f795917e5af41ab6d.jpg

78cc09341bd5dea1d440e468e5fea8e3.jpg

102be0a4e04b9a1427e1b27a813b1857.jpg

Share this post


Link to post
Share on other sites

install DCPI-manager and upload the images.

The orange icons are no problems that can resolve, create a raw dsdt and upload it here.

I'm just amazed that your CPU is not recognized, although supported by the kernel and should be displayed correctly.

Share this post


Link to post
Share on other sites

install DCPI-manager and upload the images.

The orange icons are no problems that can resolve, create a raw dsdt and upload it here.

I'm just amazed that your CPU is not recognized, although supported by the kernel and should be displayed correctly.

OK; will install DCPI-manager later, is there a workaround to show my CPU`s ?

Share this post


Link to post
Share on other sites

Edit:

upload your full Extra folder if Enoch bootloader is used, otherwise if used clover bootloader then upload the Kexts folder.

Share this post


Link to post
Share on other sites

Edit:

upload your full Extra folder if Enoch bootloader is used, otherwise if used clover bootloader then upload the Kexts folder.

have ENOCH Bootloader, will upload too. We can also make a teamviewer session later if you want to help me by remote, let me know.

Seems you are really in HACK MAC

Share this post


Link to post
Share on other sites

OK; will install DCPI-manager later, is there a workaround to show my CPU`s ?

Yes, that is possible

(....womöglich fehlt ein Treiber, daher folge den oberen Anweisungen)

Share this post


Link to post
Share on other sites

Yes, that is possible

(....womöglich fehlt ein Treiber, daher folge den oberen Anweisungen)

Yes, great -- will follow, will be back online @ 9p.m. Let's stay in contact then

Share this post


Link to post
Share on other sites

Ok

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By karthiksh1989
      can somebody walkthrough with the mojave installation guide?
      i have a mac high sierra 13.6 version on my macbook pro and want to install mojave on my desktop
      Exact config is Gigabyte gaming wifi 7 motherboard amy ryzen 7 2nd gen 2700X processor Gigabyte G1 8GB grapgic card VEGA 64
      running 2 nvme Samsung 256gb cards and 1 intel 180gb ssd internal and 1tb WD HDD, with 64 GB 3200Mhz Ram
       
      https://wa.me/919611736534 (whatsapp)
    • By Fede1132
      Hi guys i have a problem install macOs Mojave on my PC, I have this configuration:

      CPU: Ryzen 7 2700X;
      GPU1: GTX 970 Strix(For game rendering and 144Hz Monitor);
      GPU2: GTX 750ti Strix(For 2nd monitor rendering to get 100% performances from 1st 144Hz Monitor);
      MotherBoard: MSI x470 GAMING PLUS
      Hard Disk 1 (Windows 10): Samsung EVO M.2;
      Hard Disk 2 (For Storage): RAID (1) between two hard disks;
      Hard Disk 3 (For Mojave): Kingston SSD 120GB;

      I have created my USB with this:
       
      Create Bootable USB Code: sudo /Applications/Install\ macOS\ Mojave.app/Contents/Resources/createinstallmedia --volume /Volumes/USB -- /Applications/Install\ macOS\ Mojave.app -- nointeract && say Done. Clover Settings: Boot: Verbose; dart=0; nv_disable=0; kext-dev-mode=1; GraphicsEnabler=No; XMPDetection = No. Cpu: C6. Devices: (Not Enabled = [ ] - Enabled = [-] - Full Enabled [✓]) Inject (Full Enabled); Add ClockID (Full Enabled); FixOwnership (Full Enabled); Gui: (Not Enabled = [ ] - Enabled = [-] - Full Enabled [✓]) Enabled (Full Enabled); Screen Resolution: 1920x1080; Kernel and Kext Patches: (Not Enabled = [ ] - Enabled = [-] - Full Enabled [✓]) Apple RTC (Full Enabled); KernelPm (Full Enabled); SMBIOS: iMac(18,3); System Parameters: Inject Kexts = Yes; Inject System ID; Used Kexts: FakeSMC FakePCIID NVIDIA WEB LILU BIOS: VT-d = Disabled; XHCI Hand-Off = Enabled; Legacy USB Support: Enabled; Hard Disk: AHCI Mode; Selection Mode: Legacy + EUFI; Clover Install Log:
      Full Error Log:
       
    • By tokia
      Hello,
       
      My desktop Hackintosh is running macOS Mojave 10.14.2 with two dedicated GPUs installed: NVIDIA GTX 1080 Ti, AMD Radeon HD 7970.
       
      The AMD GPU is used primarily under macOS and the NVIDIA one under Windows.
       
      macOS boots without issues as long as there are no displays connected to the NVIDIA GPU. If a display is connected then the display connected to the AMD GPU will become blank. The system can be accessed using Screen Sharing/VNC.
       
      There are no problems if I swap PCI-e slots for the GPUs so that the AMD GPU is in the first slot (primary GPU), but I prefer not to do this.
       
      I have tried to remove the whole PCI (bridge) device in the DSDT file and all the lines that refer to it. The PCI entries in ioreg and System Information are gone but System Information still shows an NVIDIA GPU under Graphics/Display.
       
      Many of the suggestions I have found in guides and forum posts do not seem to apply here. My problem with some of the guides and answers is that they give the solution without explaining how anything works, or they tell you what to do without explaining the reasons behind it.
       
      What else can I do? Thank you for any assistance you can provide!
       
      I have attached some files that may help you help me.
       
      DSDT_BIOS_3101.zip contains the original ACPI (*.aml) files without any patches.
      Send me Steffens-iMac.zip is a file produced by RunMe.app, and do contain simple patches to rename some devices.
      DSDT.dsl.patch is a diff of the original DSDT.dsl file and the one with the PCI devices removed (commented out).
       
      Motherboard: ASUS Rampage V Extreme (X99), BIOS version 3101 (macOS does not boot with anything newer).
      Clover version: 4813.
       
      DSDT.dsl.patch:
      --- /Users/sl/Desktop/DSDT_BIOS_3101/DSDT.dsl 2018-12-17 05:24:30.000000000 +0100 +++ /Volumes/EFI/EFI/CLOVER/ACPI/patched/DSDT.dsl 2018-12-17 16:52:08.000000000 +0100 @@ -5,7 +5,7 @@ * * Disassembling to symbolic ASL+ operators * - * Disassembly of DSDT.aml, Mon Dec 17 05:24:30 2018 + * Disassembly of DSDT.aml, Mon Dec 17 04:01:52 2018 * * Original Table Header: * Signature "DSDT" @@ -2128,7 +2128,7 @@ ^^PCI0.BR2B.OSHP () ^^PCI0.BR2C.OSHP () ^^PCI0.BR2D.OSHP () - ^^PCI0.BR3A.OSHP () + //^^PCI0.BR3A.OSHP () ^^PCI0.BR3B.OSHP () ^^PCI0.BR3C.OSHP () ^^PCI0.BR3D.OSHP () @@ -2274,7 +2274,7 @@ ^^PCI0.BR2B.OSHP () ^^PCI0.BR2C.OSHP () ^^PCI0.BR2D.OSHP () - ^^PCI0.BR3A.OSHP () + //^^PCI0.BR3A.OSHP () ^^PCI0.BR3B.OSHP () ^^PCI0.BR3C.OSHP () ^^PCI0.BR3D.OSHP () @@ -2420,7 +2420,7 @@ ^^PCI0.BR2B.OSHP () ^^PCI0.BR2C.OSHP () ^^PCI0.BR2D.OSHP () - ^^PCI0.BR3A.OSHP () + //^^PCI0.BR3A.OSHP () ^^PCI0.BR3B.OSHP () ^^PCI0.BR3C.OSHP () ^^PCI0.BR3D.OSHP () @@ -2570,7 +2570,7 @@ ^^PCI0.BR2B.OSHP () ^^PCI0.BR2C.OSHP () ^^PCI0.BR2D.OSHP () - ^^PCI0.BR3A.OSHP () + //^^PCI0.BR3A.OSHP () ^^PCI0.BR3B.OSHP () ^^PCI0.BR3C.OSHP () ^^PCI0.BR3D.OSHP () @@ -2803,12 +2803,14 @@ If ((CSTA (Arg0, Arg1) == 0x00)) { FLAG = 0x00 - PRID (APID = 0xFF) = 0xFF + APID = 0xFF + PRID = 0xFF } Else { Local0 = APID - PRID (FLAG = 0x01) = Local0 + FLAG = 0x01 + PRID = Local0 } Return (APIC) @@ -15259,7 +15261,7 @@ ^BR2B.OSHP () ^BR2C.OSHP () ^BR2D.OSHP () - ^BR3A.OSHP () + //^BR3A.OSHP () ^BR3B.OSHP () ^BR3C.OSHP () ^BR3D.OSHP () @@ -26861,7 +26863,7 @@ } } - Device (BR3A) + /*Device (BR3A) { Name (_ADR, 0x00030000) // _ADR: Address OperationRegion (MCTL, SystemMemory, 0xE0013188, 0x04) @@ -27496,7 +27498,7 @@ { Name (_ADR, 0xFFFF) // _ADR: Address } - } + }*/ Device (BR3B) { @@ -30267,7 +30269,7 @@ ^^PCI0.BR2B.OSHP () ^^PCI0.BR2C.OSHP () ^^PCI0.BR2D.OSHP () - ^^PCI0.BR3A.OSHP () + //^^PCI0.BR3A.OSHP () ^^PCI0.BR3B.OSHP () ^^PCI0.BR3C.OSHP () ^^PCI0.BR3D.OSHP () @@ -30567,21 +30569,21 @@ WordIO (ResourceProducer, MinFixed, MaxFixed, PosDecode, EntireRange, 0x0000, // Granularity 0x4158, // Range Minimum - 0x0000, // Range Maximum + 0x4158, // Range Maximum 0x0000, // Translation Offset 0x0001, // Length ,, , TypeStatic, DenseTranslation) WordIO (ResourceProducer, MinFixed, MaxFixed, PosDecode, EntireRange, 0x0000, // Granularity 0x5758, // Range Minimum - 0x0000, // Range Maximum + 0x5758, // Range Maximum 0x0000, // Translation Offset 0x0000, // Length ,, , TypeStatic, DenseTranslation) WordIO (ResourceProducer, MinFixed, MaxFixed, PosDecode, EntireRange, 0x0000, // Granularity 0x5858, // Range Minimum - 0x0000, // Range Maximum + 0x5858, // Range Maximum 0x0000, // Translation Offset 0x0000, // Length ,, , TypeStatic, DenseTranslation) @@ -37604,7 +37606,7 @@ ^^PCI0.BR2B.OSHP () ^^PCI0.BR2C.OSHP () ^^PCI0.BR2D.OSHP () - ^^PCI0.BR3A.OSHP () + //^^PCI0.BR3A.OSHP () ^^PCI0.BR3B.OSHP () ^^PCI0.BR3C.OSHP () ^^PCI0.BR3D.OSHP () @@ -37904,21 +37906,21 @@ WordIO (ResourceProducer, MinFixed, MaxFixed, PosDecode, EntireRange, 0x0000, // Granularity 0x4558, // Range Minimum - 0x0000, // Range Maximum + 0x4558, // Range Maximum 0x0000, // Translation Offset 0x0001, // Length ,, , TypeStatic, DenseTranslation) WordIO (ResourceProducer, MinFixed, MaxFixed, PosDecode, EntireRange, 0x0000, // Granularity 0x4259, // Range Minimum - 0x0000, // Range Maximum + 0x4259, // Range Maximum 0x0000, // Translation Offset 0x0000, // Length ,, , TypeStatic, DenseTranslation) WordIO (ResourceProducer, MinFixed, MaxFixed, PosDecode, EntireRange, 0x0000, // Granularity 0x4359, // Range Minimum - 0x0000, // Range Maximum + 0x4359, // Range Maximum 0x0000, // Translation Offset 0x0000, // Length ,, , TypeStatic, DenseTranslation) @@ -44941,7 +44943,7 @@ ^^PCI0.BR2B.OSHP () ^^PCI0.BR2C.OSHP () ^^PCI0.BR2D.OSHP () - ^^PCI0.BR3A.OSHP () + //^^PCI0.BR3A.OSHP () ^^PCI0.BR3B.OSHP () ^^PCI0.BR3C.OSHP () ^^PCI0.BR3D.OSHP () @@ -45241,21 +45243,21 @@ WordIO (ResourceProducer, MinFixed, MaxFixed, PosDecode, EntireRange, 0x0000, // Granularity 0x4958, // Range Minimum - 0x0000, // Range Maximum + 0x4958, // Range Maximum 0x0000, // Translation Offset 0x0001, // Length ,, , TypeStatic, DenseTranslation) WordIO (ResourceProducer, MinFixed, MaxFixed, PosDecode, EntireRange, 0x0000, // Granularity 0x4559, // Range Minimum - 0x0000, // Range Maximum + 0x4559, // Range Maximum 0x0000, // Translation Offset 0x0000, // Length ,, , TypeStatic, DenseTranslation) WordIO (ResourceProducer, MinFixed, MaxFixed, PosDecode, EntireRange, 0x0000, // Granularity 0x4659, // Range Minimum - 0x0000, // Range Maximum + 0x4659, // Range Maximum 0x0000, // Translation Offset 0x0000, // Length ,, , TypeStatic, DenseTranslation) @@ -53823,7 +53825,7 @@ Notify (\_SB.PCI0.BR2D.H007, Local0) } - If ((\_SB.PCI0.BR3A.PMEP == 0x01)) + /*If ((\_SB.PCI0.BR3A.PMEP == 0x01)) { Local0 = \_SB.PCI0.BR3A.PMEH (0x05) } @@ -53848,7 +53850,7 @@ Notify (\_SB.PCI0.BR3A.H005, Local0) Notify (\_SB.PCI0.BR3A.H006, Local0) Notify (\_SB.PCI0.BR3A.H007, Local0) - } + }*/ If ((\_SB.PCI0.BR3B.PMEP == 0x01)) { @@ -54608,11 +54610,11 @@ \_SB.PCI0.BR2D.PMEP = 0x01 } - If ((Local1 == 0x07)) + /*If ((Local1 == 0x07)) { \_SB.PCI0.BR3A.PMES = 0x01 \_SB.PCI0.BR3A.PMEP = 0x01 - } + }*/ If ((Local1 == 0x08)) { @@ -54879,10 +54881,10 @@ Notify (\_SB.PCI0.BR2D, 0x02) } - If ((\_SB.PCI0.BR3A.DEVS () != 0x00)) + /*If ((\_SB.PCI0.BR3A.DEVS () != 0x00)) { Notify (\_SB.PCI0.BR3A, 0x02) - } + }*/ If ((\_SB.PCI0.BR3B.DEVS () != 0x00)) { @@ -55927,10 +55929,10 @@ { Notify (\_SB.PCI0.BR2D, 0x00) } - Case (0x28) + /*Case (0x28) { Notify (\_SB.PCI0.BR3A, 0x00) - } + }*/ Case (0x29) { Notify (\_SB.PCI0.BR3B, 0x00) @@ -56736,11 +56738,11 @@ } } - Scope (_SB.PCI0.BR3A) + /*Scope (_SB.PCI0.BR3A) { Method (_DSM, 4, NotSerialized) // _DSM: Device-Specific Method { - If ((Arg0 == ToUUID ("e5c937d0-3553-4d7a-9117-ea4d19c3434d") /* Device Labeling Interface */)) + If ((Arg0 == ToUUID ("e5c937d0-3553-4d7a-9117-ea4d19c3434d") / * Device Labeling Interface * /)) { If (((Arg1 == 0x02) && (Arg2 == 0x00))) { @@ -56765,7 +56767,7 @@ 0x00 }) } - } + }*/ Scope (_SB.PCI1.QR1A) {  
      DSDT_BIOS_3101.zip
      Send me Steffens-iMac.zip
      DSDT.dsl.patch
    • By twikoffin
      Hello. My hardware is:
      AMD Athlon X2 7750 dual-core
      Gigabyte NVIDIA 8400GS 512MB ( [VGA] ,HDMI,DVI)
      Motherboard Gigabyte based on NFORCE without AHCI support (only IDE)
      I have successfully installed Mac OS Yosemite, Mavericks and El Capitan with AppleNFORCEATA.kext
      But I can't use it with Mac OS 10.8, don't know why, it just gives error and my internal HDD's are not appearing in Disk Utility.

       
         
    • By kamyar1979
      I have bought a 2nd hand AMD Radeon 7750 to fix my Mojave installation problems. Although the Vendor/Device Id is in AMD7000Controller.Kext, I get a black screen and with some changes a yellow screen. I can not find any useful information to fix that. All information are for High Sierra and older macOS versions. Is there any fix to resolve that? What if I buy an RX 650 for example?
×