Jump to content

164 posts in this topic

Recommended Posts

Hey Porkserver, 

 

Sorry about your illness first off.  Feel better soon!  What parts of Andres' files did you copy over to the EFI Partition to be able to get to the OSX Installer?  I can't get the Clover installer USB to boot all of the way.  It usually stops at the slashed zero indication or just reboots.  I have a Z170X-Gaming 7, 6700K, 2 Intel 750 series 400GB NVME drives (most likely my problem), and a Titan X.  Thanks.

Share this post


Link to post
Share on other sites
Advertisement

Hey Porkserver, 

 

Sorry about your illness first off.  Feel better soon!  What parts of Andres' files did you copy over to the EFI Partition to be able to get to the OSX Installer?  I can't get the Clover installer USB to boot all of the way.  It usually stops at the slashed zero indication or just reboots.  I have a Z170X-Gaming 7, 6700K, 2 Intel 750 series 400GB NVME drives (most likely my problem), and a Titan X.  Thanks.

Inside Andres zip he posted there is a UEFI folder.  Once I figured out my own mistakes I used the ACPI and Kext folders located inside plus the config file.  Just be sure once you get installed to NOT use his DSDT file and produce your own clean one using F4 prior to booting.  One thing I also noticed with the BIOS settings is things did not work 100% until I booted into windows once after making the IOAPIC = Disabled, XHCI Handoff =Enabled and Serial = Disabled.  After that I stopped getting hangs on USB during boot.  Using his files is fine for the purposes of the install, after the initial install I used the thumb drive as the boot device and selected my fresh installed drive.  From there you can do the OSX setup assistant and then install a clean Clover bootloader on your drive and place his config.plist, file and Kext folder.  Use your own DSDT file produced and edit as needed.

 

Also be sure to add the Pike AppleAPIC patch to the clover config. https://pikeralpha.wordpress.com/2015/11/06/appleapic-kext-binary-patch-for-skylake/

 

Hope that helps!

 

 

Screen_Shot_2015_12_17_at_3_23_38_PM.png

Screen_Shot_2015_12_17_at_3_23_47_PM.png

Share this post


Link to post
Share on other sites

Sorry guys for my DSDT that make trouble for you.

Tonight i will upload 2 file,,, 
1. With my Full Config (already working)
2. With No DSDT, just set from config.plist. So your graphic card can be detected normally.

I will upload soon tonight  :thumbsup_anim:  :thumbsup_anim:  :thumbsup_anim:  :thumbsup_anim:

Share this post


Link to post
Share on other sites

Im pretty sure that people that can barely speak english should not be allowed to run OS X...

I'm pretty sure you have no place on InsanelyMac.... The majority of people contributing to a lot of the work that happens here are not from Murrica chief.  You should check your privilege and show some respect to the community.

Share this post


Link to post
Share on other sites

Andres ZeroCross: Just noticed in your image files you have Intel 10 SATA/Express showing.

 

Update: Intel 10 Series does indeed work in the G1 Gaming mobo. Stupid cable problem!

Share this post


Link to post
Share on other sites

@Andres, Did you have a chance to upload your most current EFI folder and config?  I'm up and running but I am hoping to resolve some lingering issues.  All my USB devices work but I am having a terrible time with audio from my USB headset.

Share this post


Link to post
Share on other sites

@Andres, Did you have a chance to upload your most current EFI folder and config?  I'm up and running but I am hoping to resolve some lingering issues.  All my USB devices work but I am having a terrible time with audio from my USB headset.

What kind of your audio codec?

 

Wait,, i am wake up at middle night,, now i am on :D

Let upload the file  :thumbsup_anim:  :thumbsup_anim:  :thumbsup_anim:

Share this post


Link to post
Share on other sites

I am not totally sure what the USB headset uses.  Its a Razer Krakken 7.1 headset.  I am posting my system profile, my DSDT and IORegistry dumps for you to look at if you have time to help.  

 

I noticed in the config folders you posted you just have 4 kexts in there.  Do you install your Audio kexts and FakeSMC plugins to S/L/E?

 

ANY help is appreciated!  I am smart enough to be dangerous but could use a nudge in the right direction....

Dumps!.zip

Share this post


Link to post
Share on other sites

I am not totally sure what the USB headset uses.  Its a Razer Krakken 7.1 headset.  I am posting my system profile, my DSDT and IORegistry dumps for you to look at if you have time to help.  

 

I noticed in the config folders you posted you just have 4 kexts in there.  Do you install your Audio kexts and FakeSMC plugins to S/L/E?

 

ANY help is appreciated!  I am smart enough to be dangerous but could use a nudge in the right direction....

Your IOREG Output is corrupt,, you must use IOREG 2.1 not later revision.

 

So, i assume your USB Headset is not detected at Audio Prefences?? How about System Report -> USB. Is your USB Headset detected??

Share this post


Link to post
Share on other sites

Hi Andres,

 

I know you are up late but did you post the file upload you were talking about?

 

Thanks.

Cek first post  :yes: 

 

You can use "General Setting Clover" folder that i have uploaded at drop box.

 

I don't know, i can't edit and upload new file at my post, so i edit the post and give link to dropbox  :thumbsup_anim:

Share this post


Link to post
Share on other sites

My USB headset and all other devbices show up and work.  However when I use apps like Skype and Discord the Audio through my headset is chirpy and garbled.

 

Here is a fresh copy of my dump using IOReg 2.1, I had to go find the right version...  I am poking through some other posts to see if I need to adjust settings in Audio/Midi setup.  The other weird thing with USB devices is I still need to hotplug my mouse and sometimes my webcam and other devbices multiple times to get them to show up on a reboot.

 

I will compare your config file to the one i'm using and see if I have made more Mistakes  :whistle:

Lordaeron.zip

Share this post


Link to post
Share on other sites

My USB headset and all other devbices show up and work.  However when I use apps like Skype and Discord the Audio through my headset is chirpy and garbled.

 

Here is a fresh copy of my dump using IOReg 2.1, I had to go find the right version...  I am poking through some other posts to see if I need to adjust settings in Audio/Midi setup.  The other weird thing with USB devices is I still need to hotplug my mouse and sometimes my webcam and other devbices multiple times to get them to show up on a reboot.

 

I will compare your config file to the one i'm using and see if I have made more Mistakes  :whistle:

Hi, dude

 

Try this file,,, just put in all file inside "Clover" folder to your mine

Then install "AppleHDA.kext" to your System with "kext utility"

 

Let me know if it works for you  :drool:

PorkServer.zip

Share this post


Link to post
Share on other sites

I think I made a mistake somewhere.  I installed the AppleHDA.kext to S/L/E and added the replaced the others in my CLOVER/Kexts folder as you said to do.  I can see the hardware in the system profiler, but nothing is in my Audio settings.  I am currently repairing permissions again and clearing caches manually.  Will see what happens after next reboot.

 

Thanks again for your time and assistance!

 

 

post-87026-0-17136600-1450572220_thumb.png

post-87026-0-61672800-1450572226_thumb.png

Share this post


Link to post
Share on other sites

You need to use DSDT too,,, i have modified your DSDT. Try to use it. Put it at EFI/CLOVER/ACPI/Patched

I am using the DSDT you enclosed.  I had it loading at one point but it stopped.  I am checking extensions folder to assure voodoo and others are gone.

Share this post


Link to post
Share on other sites

Can you uploade image of Verbose log?? I want to see it


Another way is you need to tick "Fix HDA" because default device audio at SkyLake is HDAS, and we need to change it to HDEF so tick "Fix HDA", then you need to DROP OEM DSM of HDA because if you want to set Layout ID "2" at config.plist, first you must remove OEM DSM of your HDAS/HDEF.

Try it

Share this post


Link to post
Share on other sites

post-826544-0-92396500-1450638054_thumb.jpgpost-826544-0-87859200-1450638088_thumb.jpg

 

Andres's Creative setup works in my Gaming G1 Profile too. Just need to sort out my dsdt like above.

Share this post


Link to post
Share on other sites

Andros, Ive hit upon a snag with the GIGABYTE Gaming G1. Id been using a PCIe USB 3 card of recent weeks but decided to see if any of the motherboards USB ports would work since developments and take out the PCIe card. Also one of my front side USB3 blue ports has a pin broken so I have to get round to soldering it back together at some stage but wondered if a missing pin would effect other parts of the USB chain. The fronts list as HS04 4 port from 14410000 to 1440000 and the broken pin means port 14420000 doesn't work. So I should be ok Id have thought with one missing port.

 

What I would like to know.

 

Did all your USBs show up from HS01 all the way upto the USR ports when you used USBInjectAll for your board ? Im only getting HS01 to HS10 and since I have a very similar board to yours I wondered why this was occurring. 

 

In System Information > USB I see the non working device listed as USB 3.0 Bus with;-

USB 3.0 Bus:

 

  Host Controller Driver: AppleUSBXHCIPCI

  PCI Device ID: 0x15b6 

  PCI Revision ID: 0x0000 

  PCI Vendor ID: 0x8086

 

Nothing I do can get it working it seems.

 

Could you take a look?

 

Here attached is my ioregistryexplorer file zipped if you need it.

 

Thanks

 

 

 

 

PS   The other device is fine as in;-

 

USB 3.0 Bus:

 

  Capacity: 15.63 GB (15,631,122,432 bytes)

  Removable Media: Yes

  BSD Name: disk8

  Host Controller Driver: AppleUSBXHCISPT

  Partition Map Type: GPT (GUID Partition Table)

  PCI Device ID: 0xa12f 

  PCI Revision ID: 0x0031 

  PCI Vendor ID: 0x8086 

  Volumes:

EFI:

  Capacity: 209.7 MB (209,715,200 bytes)

  BSD Name: disk8s1

  Content: EFI

  Volume UUID: 0E239BC6-F960-3107-89CF-1C97F78BB46B

USB:

  Capacity: 15.29 GB (15,287,148,544 bytes)

  Available: 4.56 GB (4,556,734,464 bytes)

  Writable: Yes

  File System: HFS+

  BSD Name: disk8s2

  Mount Point: /Volumes/USB

  Content: Apple_HFS

  Volume UUID: C313FE0C-6EF5-30EF-A576-FD4268662199

 

USB Optical Mouse:

 

  Product ID: 0x2510

  Vendor ID: 0x093a  (Pixart Imaging, Inc.)

  Version: 1.00

  Speed: Up to 1.5 Mb/sec

  Manufacturer: PixArt

  Location ID: 0x14800000 / 3

  Current Available (mA): 1000

  Current Required (mA): 100

  Extra Operating Current (mA): 0

  Built-In: Yes

 

Corsair K65 RGB Gaming Keyboard:

 

etc...etc....

gamingG1-ioregistryexplorer.zip

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By glasgood
      GLASGOOD'S
       
      MOJAVE HACKINTOSH GUIDE 
       

       
       
       
      **FOR**  GIGABYTE Z390 AORUS PRO
       
       
       
       
      CREDITS & THANKS
       
      @MaLd0n
      His help with EFI configuration and DSDT
       
      CLOVER  TEAM
      Slice, Kabyl, usr-sse2, jadran, Blackosx, dmazar, STLVNUB, pcj, apianti, JrCs, pene, FrodoKenny, skoczy, ycr.ru, Oscar09, xsmile, SoThOr, rehabman, Download-Fritz, Zenit432, cecekpawon Et al
       
      APPLEALC
      Acidanthera, vit9696
       
      VOODOOHDA
      autumnrain, slice2009, zenith432
       
      ESP PRO MOUNTER
      @Micky1979 
       
      HACKINTOOL
      @headkaze
       
      CLOVER CONFIGURATOR
      Mackie100
       
      THEME ENGINE
      Alex Zielenski
       
      INSANELYMAC
      OLARILA
       
      Hackintool Tutorial
      daliansky
       
      Hackintosh Guide
      CorpNewt
       
       
      MONITORCONTROL
      JoniVR & theOneyouseek
       
       
       
      ------------------------------------------------------------------------------------------------------------------------------------------------------------
       
      UPDATES
       
       
      ------------------------------------------------------------------------------------------------------------------------------------------------------------
       
       
      PART LIST
       
      • Intel I7 8700 
      • Gigabyte Z390 AORUS PRO
      • Gigabyte AORUS RADEON RX 580 8GB ( connected to monitor with DisplayPort )
       
      • Corsair Vengeance LPX 16GB ( 2 x 8GB ) 2666MHz – CMK16GX4M2A2666C16  In this build, both memory modules are installed in memory slots DDR4_A1  and DDR4_B1 
       
      • Corsair RM650x 80 Plus Gold Power Supply Unit
      • Corsair H100i V2 AIO Hydro/Water RGB LED CPU Cooler
      • Samsung EVO 500GB SSD (2.5) macOS Mojave
      • Samsung EVO 250 GB SSD (2.5) Windows 10 Pro
      • NZXT H500 Mid Tower ATX Case
       
      • RECOMMENDED WIFI CARD → ABWB 802.11AC WI-FI With Bluetooth 4.0 PCI-Express (PCI-E) BCM943602CS  
      OR
      • WIFI and Bluetooth with BCM94331CD with PCI-e adapter (but will require AirportBrcmFixup.kext for AirDrop.. )
       
      ** Avoid Samsung EVO 970 PLUS as Hackintosh has problem with that device **
       
       
      WORKING
       
      • Sound 
      • HDMI Port on AMD RX580 / 590 ( Ensure you disable BIOS CSM if using HDMI on RX580 / RX590 )
      • HDMI Port on Aorus Z390 Motherboard ( Ensure you have correct BIOS settings as per this guide for Intel only)
      • Ethernet Port
      • WiFi
      • SSD Trim
      • USB 3.0 & 2.0 
      • AirDrop
      • iCloud
      • Hardware Acceleration
      • iMessages
      • Facetime
      • Handoff
      • Continuity
       

       

       
       
       

       
       
       
       
       
      PREAMBLE - BEFORE YOU START 
       
      Here detailed, is all the  steps towards building a successful and stable Aorus Pro Z390 Hackintosh, if you are a first time Hackintosher, this guide will have you quickly up and running with the Aorus Pro Z390 Hackintosh. To rule out any problems from the go,
      only have the disc that you plan to install macOS Mojave connected to the Aorus Pro, disconnect any other Windows / Linux or data drives, external drives from your Aorus Pro. Windows / Linux and data drives can be connected after successful installation of macOS Mojave
      If you have more than 16 GB of memory, then install macOS Mojave with just 16GB, you can later add any additional memory. Install memory modules in slots DDR4_A1  and DDR4_B1. This build has the Wi-Fi combo PCI-e adapter card installed in slot PCIEX1_3.
      The WiFi/Bluetooth PCI-e Combo card used in this Aorus Pro guide has it's 9 pin USB cable attached to motherboard header F_USB2 and is enabled in SSDT-UIAC.aml ( USB ports fix ). 
       
      Do install macOS Mojave on its own physical drive, so do not try and install macOS Mojave onto a free partition on a disc that contains Windows.
      Remove any Thunderbolt cards, Thunderbolt card can be reinserted after installation.  Double check your BIOS settings are the same as this guide. 
       
      Following are unsupported / problematic
       
      • Intel Optane ( if you have this, remove it before installation of macOS Mojave )
       
      • Samsung EVO Plus drives ( firmware problem with macOS )
       
      • XFX Radeon RX 580
       
      • NVIDIA GTX / RTX not supported in macOS Mojave
       
      • Fenvi T919 Wireless Card, it seems Bluetooth is not working out of box for some users ( Maybe the USB port attached to Fenvi bluetooth is wrongly configured, or the SSDT-UIAC.aml port connector was not configured as Internal, or maybe some other reason )
         Save yourself a headache --->  RECOMMENDED WIFI CARD WORKING OUT OF BOX (OOB)  is ---> ABWB 802.11AC WI-FI With Bluetooth 4.0 PCI-Express (PCI-E) BCM943602CS 
       
      Q - WILL THIS GUIDE WORK WITH MY NON AORUS Z390 MOTHERBOARD ?
      A - Possibly may work with other Z390 chipset motherboards, but you will have to remove SSDT-UIAC.aml from Clover / ACPI / patched from the PRE-INSTALL EFI and enable the ports limit patch.
       
       
       
       
       
      PART 1 - DOWNLOAD 
       
       
      Download the following:
       
      • CLOVER
       
      • PRE-INSTALL Aorus Pro Z390 EFI - RX580.zip
       
      • POST-INSTALL Aorus Pro Z390 EFI - RX580.zip 
       
       
       
       
       
      // INTEL UHD 630 EFI  Aorus Pro Z390 EFI's below. For those who do not have a Graphics Card Installed in PCIe Slot, requires Initial Display Output BIOS setting to be changed to IGFX  spoiler below!
       
      •  PRE-INSTALL Aorus Pro Z390 EFI - Intel UHD630.zip
       
      • POST-INSTALL Aorus Pro Z390 EFI - Intel UHD630.zip
       
       
       
       
       
      • ESP MOUNTER PRO v1.9
       
      • macOS MOJAVE 
       
      • CLOVER CONFIGURATOR
       
      • EmuVariableUefi-64.efi  ( Used only to initialise iMessages. It then must be removed from Clover drivers64UEFI folder as will cause intermittent memory allocation errors on boot, explained in guide)
       
       
      OPTIONAL DOWNLOADS
       
      • Native Display Brightness with MonitorControl
       
      • VoodooHDA.kext.zip 

      • ThemeEngine 
       
      • Assets.car 
       
       
      // Not really needed but IF no sound on Wake from Sleep then use SSDT-ALC1220 and CodecCommander
      • SSDT-ALC1220.aml  ( Resolves Audio Sound on Wake, place in Clover / ACPI / Patched )
       
      • CodecCommander.kext.zip ( Resolves Audio Sound on Wake, place in Clover / Kexts / Other )
       
       
       
       
      PART 2 - BIOS SETTINGS (version F9 )
       
       
      Here is a list of the BIOS settings that I have used ( Screenshots in spoiler below )
       
      • Enter BIOS → Press F12 → Enter Setup
      • Save & Exit → Load Optimized Defaults
       
      • BIOS → Windows 8/10 Features → Other OS
      • BIOS → CSM Support → Enabled
       
      • Peripherals → Initial Display Output → PCIe 1 Slot
      • Peripherals → Trusted Computing → Security Device Support →  Disable
      • Peripherals → Intel(R)Bios Guard → Intel BIOS Guard Support →  Disable
      • Peripherals → USB Configuration → Legacy USB Support →  Enabled
      • Peripherals → USB Configuration → XHCI Hand-off →  Enabled
      • Peripherals → Network Stack Configuration → Network Stack →  Disabled
      • Peripherals → SATA And RST Configuration → SATA Mode Selection →  AHCI
       
      • Chipset → Vt-d → Enabled
      • Chipset → Internal Graphics → Enabled
      • Chipset → DVMT Pre-Allocated → 256M
      • Chipset → DVMT Total Gfx Mem → MAX 
      • Chipset → Audio Controller → Enabled
      • Chipset → Above 4G Decoding → Disabled 
       
      • Power → ErP → Disabled
      • Power → RC6 (Render Standby) → Disabled
       
      // IF USING  CORSAIR H100i V2 AIO CPU WATER COOLER 
      • MIT → Smart Fan 5 Settings → CPU Fan Control mode → PWM 
       
      • Save & Exit → Save & Exit Setup
       
      SCREEN DUMP SPOILERS
       
       
       
       
       
      PART 3 – CREATE A MOJAVE USB FLASH INSTALLER
       
      Prepare USB Installer for Mojave ( Video below )
       
      • Insert USB drive
      • Launch /Applications/Utilities/Disk Utility
      • Disk Utility → View → Show All Devices
      • On Left-hand panel → External →(Identify your USB device in left hand panel)
      • Click and highlight your USB device in the left-hand panel.
      • Click erase button.
      • Name: USB
      • Format: Mac OS Extended (Journaled )
      • Scheme: GUID Partition Map
      • Click Erase button.
       
      • Place the downloaded MacOS Mojave app into Applications folder.
      • Open Terminal copy and paste:
       
      sudo /Applications/Install\ macOS\ Mojave.app/Contents/Resources/createinstallmedia --volume /Volumes/USB --nointeraction && say Mojave Drive Created  • Enter
       
       
       
       
       
       
       
       
       
       
       
      PART 4 – INSTALL CLOVER ON THE MOJAVE USB INSTALLER 
       
      Make Mojave USB flash drive installer bootable.( Video below )
       
      • Launch Clover application, double click.
      • Click Continue → Continue → Continue 
      • Click Change Install Location button.
      • Click Install macOSMojave USB installer → Continue
      • Click Customise button
      • Choose:
      Clover for UEFI booting only Install Clover in the ESP Themes UEFI Drivers Install RC scripts on target volume    NO NEED TO INSTALL RC SCRIPTS ON USB INSTALLER • Click Install button
      • Installation Complete!
       
      Video:
       
       
       
       
       
       
      PART 5 – CUSTOMIZE MOJAVE USB INSTALLER FOR AORUS Z390 PRO
       
      Replace Clover EFI folder with PRE-INSTALL Aorus Pro Z390 EFI - RX580.zip  OR  if NO graphics card installed in PCIe slot, then use PRE-INSTALL Aorus Pro Z390 EFI - Intel UHD630.zip( Video below ) 
       
      • Install ESP Mounter Pro v1.9
      • Using ESP Mounter Pro, Mount ESP on disk2s1 ( Your disk name may be different )
       

       

       
       
       
      • Open mounted EFI partition found on desktop
      • Copy all the contents from Aorus 390 Pro EFI folder
      • Replace USB EFI folder with all the contents inside the Aorus 390 Pro EFI folder.
       
       

       
       
       
       
       
       
       
      PART 6 – INSTALL MAC OS MOJAVE ON INTERNAL DRIVE
       
      INSTALL NOTE
       
      ENSURE BIOS: Above 4G Decoding is set to Disabled 
      if Above 4G decoding is set to enabled then macOS Mojave install will freeze at 2 mins remaining and will not shut down properly!!!!
       
      Please be patient during install, so when install gets to 2 or 3 mins remaining then it may take extra time. Be ready to boot from UEFI USB installer by pressing F12 when install initiates restarts. 

      • INSERT USB INSTALLER INTO THE USB 2.0 PORT  
       
       
       Here is a walkthrough of the full process using the macOS Mojave USB Installer on the Aorus Z390 Pro. 
       
       
       
       
      • Power on PC and press F12• Choose bootable USB drive from boot menu.
       
       
       
      • Install macOS Mojave to internal solid state or hard drive.
       
       
       
      When system returns to the Clover boot menu choose:
       
      • Boot macOS Install from Macintosh
       
       
       
      At next restart, press F12 and boot from external UEFI USB device and choose:
       
      • Boot macOS Install from Macintosh
       
       
       
      Proceed with macOS Mojave install
       
       
      macOS Mojave is now installed, but it can only boot at this moment thanks to FakeSMC and Clover on the Mojave USB flash drive installer.
       

       
       
       
       
       
       
      PART 7 – MAKE AORUS Z390 PRO INTERNAL DRIVE BOOTABLE
       
      Make internal drive bootable ( Video below )
       
      So far, the Aorus Pro can only boot the internal system drive with the aid of the Mojave USB Installer.
      To boot from the internal system drive without the installer: 
       
      Download and install Clover with RC Scripts on target volume.  
      If your Aorus Pro Z390 has AMD RX 580 then copy the EFI folder from inside POST-INSTALL Aorus Pro Z390 EFI - RX580.zip  folder and paste it inside the the System Drive EFI partition.          OR
      If your Aorus Pro Z390 has no graphics card installed in PCIe slot, then copy the EFI folder from inside POST-INSTALL Aorus Pro Z390 EFI - Intel UHD630.zip  folder and paste it inside the the System Drive EFI partition.   
       

       
       
       
      • Remove USB Mojave installer and shut down and restart.
       
      Aorus Hackintosh should now be able to boot to macOS Mojave, Done, well almost ! 
       
       
       
       
       
      PART 8 – ENABLE IMESSAGES & FACETIME 
       
       
      // UPDATE 21st MAY 2019
       
      Past experience suggests Clover Configurator now automatically populates correct values for working iMessages when you select an SMBIOS.  
       

       
      After selecting SMBIOS, example iMac19,1 for Aorus Pro with RX580 ( image above ) then go to Apple and ensure you have the "serial number is not valid " message. Done!
       
      If you still have problems connecting to iMessage, test and ensure that AirDrop is working, then follow instructions inside spoiler. 

       
       
      • Mount internal drive EFI/ESP partition
      • Go to folder CLOVER → drivers64UEFI 
      • Place both EMUVariableUefi-64.efi inside → drivers64UEFI
       
       
      Using Clover Configurator, add the following argument to config.plist using Clover Configurator.
       
      • Slide = 0
       

       
       
      Shutdown and then press power on button on PC.
       
      • You should now be able to Log into iCloud, iMessages and FaceTime
       
       
       
      • NOW delete EMUVariableUefi-64.efi from CLOVER → drivers64UEFI Folder 
      • Shutdown and restart Aorus Pro hackintosh. iMessages etc is now operational without EMUVariableUefi-64.efi ( EMUVariableUefi-64.efi only needed to initialise iMessages )
       
       
      // UPDATE 22nd May 2019 
       
      • It seems that there are no "Couldn't allocate runtime area"  errors when continuing to use EMUVariableUefi-64.efi since updating to macOS Mojave 10.14.5 and using Clover version r4920. 
      • It is important to delete EMUVariableUefi-64.efi, this will avoid very intermittent boot errors such as: “Couldn’t allocate runtime area”  post errors.
       
       
       
       
      PART 9 – ENABLE TRIM for Solid State Flash Drives
       
      Open Terminal and enter the following command:
      sudo trimforce enable  
       
       
       
       
      DEFAULT SSDT –  USB PORTS FIX CONFIGURATION WITH FRONT USB-C - SSDT ALREADY INSIDE AORUS Z390 EFI FOLDER  – Provided by @AudioGod 
       
       

       

       
      If you have USBC on Computer Chassis / Case, then SS01 and SS02 is mapped to that USB C port 
       

       
       
       
       
       
       
      ------------    GUIDE FINISHED YOU SHOULD NOW HAVE WORKING AORUS Z390 PRO HACKINTOSH  WITH SSDT USB FIX   ------------
       
       
       
      OPTIONAL: Set Wi-Fi Country Code
       
       
       
       
       
       
      OPTIONAL: System Information - PCI
       
       
       
       
       
       
       
      OPTIONAL:  Enable HDMI Audio on RX580
       
       
       
       
       
       
       
      OPTIONAL:  Native Display Brightness - with MonitorControl

       
       
       
       
       
       
      OPTIONAL:  Dual Boot macOS Mojave & Windows 10 
       
       
       
       
       
       
       
       
      OPTIONAL:  Replace the default "About This Mac" Apple Logo with RED AORUS APPLE
       
       

       
       
       
       
      OPTIONAL - ALTERNATIVE SSDT 1 –  SSDT Ports configuration below - replace SSDT inside Clover /ACPI/PATCHED folder 
       
       
       
       
       

      OPTIONAL - ALTERNATIVE SSDT 2 -  SSDT Ports configuration below - replace SSDT inside Clover /ACPI/PATCHED folder 
       
       
       
       
       

      OPTIONAL - ALTERNATIVE SSDT 3 – Create your own SSDT
       
       
       
       
       
      FRAMEBUFFER PATCHING  – For working Intel UHD 630 Graphics, working HDMI Port, working HDMI Audio on Aorus Z390 Pro
       


       
       
       
       
       
       
      RECOMMENDED READING  – Excellent Hackintosh Vanilla guide created by CorpNewt with in depth tutorial on Clover.  
       
      https://hackintosh.gitbook.io/-r-hackintosh-vanilla-desktop-guide/config.plist-per-hardware/coffee-lake
       
       
       
       
       
       
       
      FOR MORE HACKINTOSH INFORMATION SUCH AS USB PORTS FIX, CLOVER CONFIGURATOR, HACKINTOSH BACKUP WITH CARBON COPY CLONER .....   THEN SEE MY PREVIOUS GUIDE FOR ASUS Z370-G Strix
       
       
       
       
       
       
       
       
       
       
       

       
       
       
       
       
       
       
       
      SSDT-UIAC.aml.zip
      SSDT-UIAC.dsl.zip
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
    • By MaLd0n
      ---INSTALLATION TUTORIAL---
       
      ---Original Post---
      https://olarila.com/forum/viewtopic.php?f=45&t=9172
       
      ---USB---
      https://pikeralpha.wordpress.com/2016/07/13/simple-skylake-usb-fix-no-kexts-required/
       
      ---CLOVER FOLDER---
       
      CLOVER.zip
       
       
      --MOBO
      GigaByte Z390 M Gaming



      --PROCESSOR
      Intel Core i9-9900K


      --COOLER
      CoolerMaster MasterLiquid ML120R RGB


      --MEMORY
      Corsair Dominator Platinum 16GB (2 x 8GB)


      --GPU
      Sapphiretech Radeon RX 590 8 GB GDDR5


       
      --SSD
      Samsung 970 EVO NVMe M2 Flash Drive


      --POWER SUPPLY
      EVGA 750 N1, 750W


      --WIRELESS
      TP-Link Archer T9E


      --BLUETOOTH
      Orico BTA-403


      --CASE
      Thermaltake View 21 Tempered Glass Edition


      --DSDT Patches--
      -FIX ERRORS AND WARNINGS -FIX ACPI ERRORS -REMOVE UNUSED SCOPES / DEVICES -HIGH PRECISION EVENT TIMER -SATA SERIE 10 ID -DMAC -REMOVE 22K LINES, PROBLEMATIC and UNUSED -FIX K.P in REBOOT -NVRAM / REAL TIME CLOCK -SLPB -DARWIN / WINDOWS 2015 -XHCI -PLUGIN TYPE -HDAS to HDEF -HDEF -REAL TIME CLOCK -ARTC -IRQs -SBUS -MIKEY -BUS1 -MCHC -ALS0 -SHUTDOWN -UAR1 -LAN -FWHD -USBX -PMCR -PPMC -XSPI -GMM -IMEI -EC -PNLF -ARPT -GFX0 -NVME -DTGP -ACQUIRE MUT0 0XFFFF -OPERATION REGION GPIO -MUTEX MUT0 0x00 -EXTERNAL REFERENCES -UNKNOWNOBJ -HDMI / HDAU -FULL RENAMED DEVICES  
      --SCREENSHOTS--





























      --BruceX--
       
      --USB-C-- test with SanDisk Ultra USB-STICK 128gb


       
      -Credits and thanks to the old and new people in the community who developed patches, kexts and bootloaders!
      Slice, Kabyl, usr-sse2, jadran, Blackosx, dmazar, STLVNUB, pcj, apianti, JrCs, pene, FrodoKenny, skoczy, ycr.ru, Oscar09, xsmile, SoThOr, RehabMan, Download-Fritz, Zenit432, cecekpawon, Intel, Apple, Oracle, Chameleon Team, crazybirdy, Mieze, Mirone, Oldnapalm, netkas, Elconiglio, artut-pt, ErmaC, Pavo, Toleda, Master Chief and family, bcc9, The King, PMheart, Sherlocks, Micky1979, vit9696, vandroiy2013, Voodoo Team, Pike R. Alpha, lvs1974, Austere.J, CVad, Sampath007, onemanosx, erroruser, Jenny David, Olarila Facebook Community, Hackintosh Facebook Community and many others!
      We're all here to have fun and learn from each other!
    • By Candrahm
      Hi everybody,
       
      I'm new here and French. 
      I success to hack my Asus X751LJ and pass it to High Sierra 10.13.6, not easily, and everything works except the keyboard and the touchpad.
      I tried VoodooPS2Controller, ApplePS2SmartTouchpad, even VoodooI2C, but nothing works...
      Could someone help me? Is there a DSDT problem? Witch kext should I use?
      I post my ACPI and Kexts folders and my IOReg.
      Please... Help me. I'm desperate...
      MacBook Pro de Candrahm.ioreg
      Archive.zip
    • By rtke333
      Hi!
       
      I have everything working on my Acer notebook, except FN + Brightness keys using VoodoPS2Controller.kext
       
      Now the brightness keys are "Pause+Break = Brightness Up" and "Fn+F12 = Brightness Down" working right now but they are not the actual keys. 
      The actual brightness keys are "Fn+RightArrow = Brightness Up" and "Fn+LeftArrow = Brightness Down" but they are not working.
      The problem is I don't know the codes.
      Installed ioio and enabled debugging to console:
      Pause/Break is generating: "ApplePS2Keyboard: sending key e045=71" which upper the brightness
      Fn+F12 is generating: "ApplePS2Keyboard: sending key 46=6b" which lower the brightness
      Fn+RightArrow/LeftArrow generates nothing.
      Keyboard attached to PS2K
      Then I used rehabman's guide to enable ACPIDebugging, Installed kext to L/E, Debug methods (Instrument EC Queries, Add DSDT Debug Methods) to DSDT, but there are no codes generated to the log.
       
      Attaching debug folder.
      Also I don't know if it will help, but on Linux I got a code from decreasing/rising brightness with Fn+Left/RightArrow keys:
      Fn+RightArrow: "0xe0 0x54 0xe0 0xd4"
      Fn+Left: "0xe0 0x4c 0xe0 0xcc"
       
      Also I love using EMlyDinEsH's SmartTouchpad Driver, with that all of my Fn keys are working except Brigtness keys ofc. If there are any fix I would like to use that with the smarttouchpad driver. 
      EMlyDinEsH's SmartTouchpad Driver: https://osxlatitude.com/forums/topic/1948-elan-focaltech-and-synaptics-smart-touchpad-driver-mac-os-x/
       
      Specs in my signature. 
      Please help me fix this very last issue on my acer.
       
      debug_4751.zip
    • By End3rPower50
      Hi, i've installed on my pc MacOS Mojave but after installation my pc, sometimes, crash giving kernel panic.
      I came to the conclusion that it is a random kernel panic because sometimes it starting up and other times it isn't starting up
       
      My PC:
      CPU: Intel i7 6500U
      LAN: RTL8100
      Wi-Fi & Bluetooth: Dell DW1820A
      USB 3.1
       
      CLOVER.zip
×