Jump to content

164 posts in this topic

Recommended Posts

Hey Porkserver, 

 

Sorry about your illness first off.  Feel better soon!  What parts of Andres' files did you copy over to the EFI Partition to be able to get to the OSX Installer?  I can't get the Clover installer USB to boot all of the way.  It usually stops at the slashed zero indication or just reboots.  I have a Z170X-Gaming 7, 6700K, 2 Intel 750 series 400GB NVME drives (most likely my problem), and a Titan X.  Thanks.

Share this post


Link to post
Share on other sites
Advertisement

Hey Porkserver, 

 

Sorry about your illness first off.  Feel better soon!  What parts of Andres' files did you copy over to the EFI Partition to be able to get to the OSX Installer?  I can't get the Clover installer USB to boot all of the way.  It usually stops at the slashed zero indication or just reboots.  I have a Z170X-Gaming 7, 6700K, 2 Intel 750 series 400GB NVME drives (most likely my problem), and a Titan X.  Thanks.

Inside Andres zip he posted there is a UEFI folder.  Once I figured out my own mistakes I used the ACPI and Kext folders located inside plus the config file.  Just be sure once you get installed to NOT use his DSDT file and produce your own clean one using F4 prior to booting.  One thing I also noticed with the BIOS settings is things did not work 100% until I booted into windows once after making the IOAPIC = Disabled, XHCI Handoff =Enabled and Serial = Disabled.  After that I stopped getting hangs on USB during boot.  Using his files is fine for the purposes of the install, after the initial install I used the thumb drive as the boot device and selected my fresh installed drive.  From there you can do the OSX setup assistant and then install a clean Clover bootloader on your drive and place his config.plist, file and Kext folder.  Use your own DSDT file produced and edit as needed.

 

Also be sure to add the Pike AppleAPIC patch to the clover config. https://pikeralpha.wordpress.com/2015/11/06/appleapic-kext-binary-patch-for-skylake/

 

Hope that helps!

 

 

Screen_Shot_2015_12_17_at_3_23_38_PM.png

Screen_Shot_2015_12_17_at_3_23_47_PM.png

Share this post


Link to post
Share on other sites

Sorry guys for my DSDT that make trouble for you.

Tonight i will upload 2 file,,, 
1. With my Full Config (already working)
2. With No DSDT, just set from config.plist. So your graphic card can be detected normally.

I will upload soon tonight  :thumbsup_anim:  :thumbsup_anim:  :thumbsup_anim:  :thumbsup_anim:

Share this post


Link to post
Share on other sites

Im pretty sure that people that can barely speak english should not be allowed to run OS X...

I'm pretty sure you have no place on InsanelyMac.... The majority of people contributing to a lot of the work that happens here are not from Murrica chief.  You should check your privilege and show some respect to the community.

Share this post


Link to post
Share on other sites

Andres ZeroCross: Just noticed in your image files you have Intel 10 SATA/Express showing.

 

Update: Intel 10 Series does indeed work in the G1 Gaming mobo. Stupid cable problem!

Share this post


Link to post
Share on other sites

@Andres, Did you have a chance to upload your most current EFI folder and config?  I'm up and running but I am hoping to resolve some lingering issues.  All my USB devices work but I am having a terrible time with audio from my USB headset.

Share this post


Link to post
Share on other sites

@Andres, Did you have a chance to upload your most current EFI folder and config?  I'm up and running but I am hoping to resolve some lingering issues.  All my USB devices work but I am having a terrible time with audio from my USB headset.

What kind of your audio codec?

 

Wait,, i am wake up at middle night,, now i am on :D

Let upload the file  :thumbsup_anim:  :thumbsup_anim:  :thumbsup_anim:

Share this post


Link to post
Share on other sites

I am not totally sure what the USB headset uses.  Its a Razer Krakken 7.1 headset.  I am posting my system profile, my DSDT and IORegistry dumps for you to look at if you have time to help.  

 

I noticed in the config folders you posted you just have 4 kexts in there.  Do you install your Audio kexts and FakeSMC plugins to S/L/E?

 

ANY help is appreciated!  I am smart enough to be dangerous but could use a nudge in the right direction....

Dumps!.zip

Share this post


Link to post
Share on other sites

I am not totally sure what the USB headset uses.  Its a Razer Krakken 7.1 headset.  I am posting my system profile, my DSDT and IORegistry dumps for you to look at if you have time to help.  

 

I noticed in the config folders you posted you just have 4 kexts in there.  Do you install your Audio kexts and FakeSMC plugins to S/L/E?

 

ANY help is appreciated!  I am smart enough to be dangerous but could use a nudge in the right direction....

Your IOREG Output is corrupt,, you must use IOREG 2.1 not later revision.

 

So, i assume your USB Headset is not detected at Audio Prefences?? How about System Report -> USB. Is your USB Headset detected??

Share this post


Link to post
Share on other sites

Hi Andres,

 

I know you are up late but did you post the file upload you were talking about?

 

Thanks.

Cek first post  :yes: 

 

You can use "General Setting Clover" folder that i have uploaded at drop box.

 

I don't know, i can't edit and upload new file at my post, so i edit the post and give link to dropbox  :thumbsup_anim:

Share this post


Link to post
Share on other sites

My USB headset and all other devbices show up and work.  However when I use apps like Skype and Discord the Audio through my headset is chirpy and garbled.

 

Here is a fresh copy of my dump using IOReg 2.1, I had to go find the right version...  I am poking through some other posts to see if I need to adjust settings in Audio/Midi setup.  The other weird thing with USB devices is I still need to hotplug my mouse and sometimes my webcam and other devbices multiple times to get them to show up on a reboot.

 

I will compare your config file to the one i'm using and see if I have made more Mistakes  :whistle:

Lordaeron.zip

Share this post


Link to post
Share on other sites
On 12/20/2015 at 6:30 AM, Porkserver said:

My USB headset and all other devbices show up and work.  However when I use apps like Skype and Discord the Audio through my headset is chirpy and garbled.

 

Here is a fresh copy of my dump using IOReg 2.1, I had to go find the right version...  I am poking through some other posts to see if I need to adjust settings in Audio/Midi setup.  The other weird thing with USB devices is I still need to hotplug my mouse and sometimes my webcam and other devbices multiple times to get them to show up on a reboot.

 

I will compare your config file to the one i'm using and see if I have made more Mistakes  :whistle:

Hi, dude

 

Try this file,,, just put in all file inside "Clover" folder to your mine

Then install "AppleHDA.kext" to your System with "kext utility"

 

Let me know if it works for you  :drool:

 

Edited by Andres ZeroCross

Share this post


Link to post
Share on other sites

I think I made a mistake somewhere.  I installed the AppleHDA.kext to S/L/E and added the replaced the others in my CLOVER/Kexts folder as you said to do.  I can see the hardware in the system profiler, but nothing is in my Audio settings.  I am currently repairing permissions again and clearing caches manually.  Will see what happens after next reboot.

 

Thanks again for your time and assistance!

 

 

post-87026-0-17136600-1450572220_thumb.png

post-87026-0-61672800-1450572226_thumb.png

Share this post


Link to post
Share on other sites

You need to use DSDT too,,, i have modified your DSDT. Try to use it. Put it at EFI/CLOVER/ACPI/Patched

I am using the DSDT you enclosed.  I had it loading at one point but it stopped.  I am checking extensions folder to assure voodoo and others are gone.

Share this post


Link to post
Share on other sites

Can you uploade image of Verbose log?? I want to see it


Another way is you need to tick "Fix HDA" because default device audio at SkyLake is HDAS, and we need to change it to HDEF so tick "Fix HDA", then you need to DROP OEM DSM of HDA because if you want to set Layout ID "2" at config.plist, first you must remove OEM DSM of your HDAS/HDEF.

Try it

Share this post


Link to post
Share on other sites

post-826544-0-92396500-1450638054_thumb.jpgpost-826544-0-87859200-1450638088_thumb.jpg

 

Andres's Creative setup works in my Gaming G1 Profile too. Just need to sort out my dsdt like above.

Share this post


Link to post
Share on other sites

Andros, Ive hit upon a snag with the GIGABYTE Gaming G1. Id been using a PCIe USB 3 card of recent weeks but decided to see if any of the motherboards USB ports would work since developments and take out the PCIe card. Also one of my front side USB3 blue ports has a pin broken so I have to get round to soldering it back together at some stage but wondered if a missing pin would effect other parts of the USB chain. The fronts list as HS04 4 port from 14410000 to 1440000 and the broken pin means port 14420000 doesn't work. So I should be ok Id have thought with one missing port.

 

What I would like to know.

 

Did all your USBs show up from HS01 all the way upto the USR ports when you used USBInjectAll for your board ? Im only getting HS01 to HS10 and since I have a very similar board to yours I wondered why this was occurring. 

 

In System Information > USB I see the non working device listed as USB 3.0 Bus with;-

USB 3.0 Bus:

 

  Host Controller Driver: AppleUSBXHCIPCI

  PCI Device ID: 0x15b6 

  PCI Revision ID: 0x0000 

  PCI Vendor ID: 0x8086

 

Nothing I do can get it working it seems.

 

Could you take a look?

 

Here attached is my ioregistryexplorer file zipped if you need it.

 

Thanks

 

 

 

 

PS   The other device is fine as in;-

 

USB 3.0 Bus:

 

  Capacity: 15.63 GB (15,631,122,432 bytes)

  Removable Media: Yes

  BSD Name: disk8

  Host Controller Driver: AppleUSBXHCISPT

  Partition Map Type: GPT (GUID Partition Table)

  PCI Device ID: 0xa12f 

  PCI Revision ID: 0x0031 

  PCI Vendor ID: 0x8086 

  Volumes:

EFI:

  Capacity: 209.7 MB (209,715,200 bytes)

  BSD Name: disk8s1

  Content: EFI

  Volume UUID: 0E239BC6-F960-3107-89CF-1C97F78BB46B

USB:

  Capacity: 15.29 GB (15,287,148,544 bytes)

  Available: 4.56 GB (4,556,734,464 bytes)

  Writable: Yes

  File System: HFS+

  BSD Name: disk8s2

  Mount Point: /Volumes/USB

  Content: Apple_HFS

  Volume UUID: C313FE0C-6EF5-30EF-A576-FD4268662199

 

USB Optical Mouse:

 

  Product ID: 0x2510

  Vendor ID: 0x093a  (Pixart Imaging, Inc.)

  Version: 1.00

  Speed: Up to 1.5 Mb/sec

  Manufacturer: PixArt

  Location ID: 0x14800000 / 3

  Current Available (mA): 1000

  Current Required (mA): 100

  Extra Operating Current (mA): 0

  Built-In: Yes

 

Corsair K65 RGB Gaming Keyboard:

 

etc...etc....

gamingG1-ioregistryexplorer.zip

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.

Announcements

  • Similar Content

    • By ltooz_audis
      This is how I would create my first hackintosh MacBookPro 13,2 on HP EliteBook 820 G3. I selected this one as an example because it has Ethernet and it. can be made as a perfect MacBookPro 13,2. This procedure will actually work with all Laptops and Desktops too. Watch the videos carefully.
      1. Gather all information about the hardware, download solftware, create flash drive installer with Catalina using Clover and OpenCore boot loaders.
       
       
      2. Understand the files inside boot loader and create the config files for both Clover and OpenCore boot loader.
       
       
      3. Actual installation and post installation.
       
       
       
      Install macOS Catalina to External USB Hard Drive.
       
       
      Patch DSDT and SSDTs for perfect Sleep/Wake and USB ports power.
       
      Use External USB Wifi
       
      Install DW1820A instead of DW1560 for BT4.0 and Wifi.
      Patch AppleALC For Audio Codecs
       
      Cheers,
      Louis
    • By ngochoaic3
      Hi everyone, 
      I hava a dell precision m4700 with option dgpu amd firepro m4000, The Intel HD4000 Graphic is disable, i can't enable it on to install Hackintosh
      I'd like to enable it on and ask you for setting custom connectors to get the internal display to work, and enable the iGPU in order to get things like AirPlay screen mirroring to work
      Could you help me?
    • By tluck
      Lenovo T460 macOS with Clover Guide
      Latest Release on GitHub (July 2020) Updated to Clover r5120 Updated Lilu based kexts - Lilu, ALC, WEG Added AirportBrcmFixup.kext
        Various Tweaks over Last months The main branch in my github repo is a complete Clover ESP (/EFI) bundle and kext pack for the Lenovo T460. The current file bundle seems to work on Sierra, HighSierra, Mojave and Catalina. There is an OpenCore branch in the repo as an alternative to Clover. This guide was developed for a Clover implementation. But the thread has evolved to include discussion of both Clover and Opencore for these systems: T460 and T470 family of ThinkPads.
       
      Full Clover file set - config.plist etc. Includes all custom kexts Includes custom DSDT/SSDT scripts and patches Utility scripts The zip bundles are posted to GitHub: https://github.com/tluck/Lenovo-T460-Clover/releases
      Caveat: The T460 systems used here was configured with: i5-6300U, Intel HD Graphics 520, 1920x1080 touch screen. If you have a different system model, then extract the ACPI files and use the included scripts to create a set of files consistent with your system type and BIOS version. See below for details.
      Credits: RehabMan, Shmilee, vusun123, TimeWalker, Mieze from which, much of their work and help is/was was used to get the T460 to this point.
      Devices and aspects working:
      Ethernet -  Intel I219LM is enabled via IntelMausiEthernext.kext WiFi/BT - substitute the Intel WiFi/BT with a compatible Broadcom or Atheros chip Audio - ALC293 codec implemented via AppleALC.kext (the old AppleHDA_ALC293 and CodecCommander kexts are not needed) PS2 - ClickPad + TrackPoint + all 3 buttons - using a modified VoodooPS2Controller to support new layouts - and added some custom Fn key maps based on 440/450 dsdt USB - implemented via custom SSDT + USBInjectAll kext. All USB3/USB2 ports are intel-based and work -  3 external USB and internal Camera, BT, etc  Sleep/Wake - the sleepwatcher package and custom sleep/wake scripts are used to help with sleep/wake for BT and PS2 devices. Note: have not tried to implement the SD card reader - no driver found.
      ACPI Files
      New Installation - Steps and Details
      Part 1 - OS Installation
      Part 2- Post OS Installation and Setup
      Notes on Custom Kexts
       
    • By tonyx86
      **********************************************************************************
      In this thread, I have fully documented the installation of macOS Catalina on my HP EliteDesk 800 G4 Mini. It is a PERFECT HackMini8,1 and is running very well for me without any issues. I hope this documentation helps you to install macOS on your hack. Please leave feedback if you think there is anything I can improve and let me know if you have any questions.
      **********************************************************************************
       
      Background
      This is my first "modern" hack supporting UEFI and my first hack using Clover "on-the-fly" patches.  My previous hacks
      Laptop: Thinkpad T61 / Nvidia NVS 140m Laptop: Dell Latitude E6410 / Nvidia G3100m Desktop: Gigabyte G31 / GeForce 9600 Desktop: Biostar TH55HD / Sapphire Pulse RX580 (Google "Catalina Biostar TH55HD" and look for user name deeveedee)  
      are all perfectly running Catalina and I patched them all "manually" - all DSDT patches applied with MaciSL with virtually no Clover on-the-fly patching and all booted Legacy Clover.  This UEFI hack was MUCH easier and took about 20 hours vs. a combined hundreds of hours for the old hacks.  I wanted a hack that was a little more future proof and I think this is it.  I hope you enjoy this as much as I am enjoying it.  It is a perfect MacMini8,1.
       

       
      My system specs
      HP EliteDesk 800 G4 Mini (I7-8700T / UHD 630 / Q370 Chipset / 32GB DDR4 RAM) 3 x DP Ports (connected to monitors using DP -> DVI adapters) 6 x USB 3.1 1 x USB Type-C 3.1 2 x NVMe SSD (M.2 PCIe x4 2280/2230 combo ports) 1 x SATA6 SSD 1 x Intel Ethernet RJ-45 Conexant CX20632 Audio Codec Unsupported M.2 PCIe x1 2230 Intel Wi-Fi.  A possible solution is here, but I am NOT offering any support for this.  
      macOS Installation 
      Important: You MUST BE LOGGED-IN to download attachments from this forum
      See macOS installation steps here See Known Issues here for additional installation steps that may not yet be included in my attached config files See CLOVER (UEFI) installation later in this first post
      See BIOS configuration in attached BIOS configuration PDF document
      See EFI and /L/E kexts in attached EliteDesk.zip archive See how I developed my installation methodology here See references here See instructions here for installing two M.2 2280 NVMe SSDs and one SATA HD / SSD  
      What is not working
      Microphone port  
      What is not tested
      USB c 3.1 port (I have partially tested the USB 3 functionality of the port and it seems to be working fine with the SSDT-UIAC.aml in the attached EliteDesk800.zip archive) Wi-Fi / Bluetooth (intentional since I have not yet replaced my Intel card). A possible solution is here, but I am not offering any support for this.
       
      What is working
      Everything not mentioned above Sleep / Wake Multiple displays with IGPU graphics acceleration, hot pluggable display ports and DP->DVI adapters USB 3.1 ports Audio (internal speaker and headphone jack) Ethernet Auto-sensing headphone jack automatically switches to internal speaker when headphones removed  
      Known Issues and their solutions - see here
       
      BIOS Version / Configuration
      Version: 02.11.01 Rev.A See attached BIOS configuration in PDF document "HP EliteDesk 800 G4 Mini BIOS Configuration.pdf" Intel ME must be enabled for proper sleep / wake of UHD 630
       
      Clover Configuration
      Clover for UEFI booting only Install Clover in the ESP UEFI Drivers Recommended drivers DataHubDxe FSInject SMCHelper File System drivers ApfsDriverLoader VBoxHfs Memory fix drivers AptioMemoryFix Additional drivers NvmExpressDxe Install RC scripts on target volume Themes Choose your desired theme Install Clover Preference Pane (option not available when installing on USB thumb drive)  
      UHD 630 Framebuffer Patching
      See here and here to understand my graphics properties for use with WhateverGreen.kext Read this to see my attempt at graphics patching without WhateverGreen.kext (WEG) to get a better understanding of what WEG is doing
       
      Current Versions
      Catalina 10.15.6 Clover (UEFI) r5119 Lilu.kext 1.4.5 WhateverGreen.kext 1.4.0 AppleALC.kext 1.5.0 IntelMausi 1.0.3 (Not IntelMausiEthernet)  
      Credits To be provided
       
      ScreenShots
       
       
      HP EliteDesk 800 G4 Mini BIOS Configuration.pdf
       
      EliteDesk800 G4 Mini - Rev 1.0.zip
    • By ISmokeAir
      I am using opencore. I have an asrock z270 și killer and a core i7 7700k. I don't have a dgpu. I am using the integrated igpu(UHD 630). After booting up I get this kernel Panic.
       
×