I have a Dell Vostro 3267 system unit. It has a Skylake processor Intel Core i5-6400 with integrated graphics Intel HD 530, 8 GB RAM, 256 GB SSD. The monitor is connected via HDMI.
I faced a problem that if I enter Hackintosh in a sleep mode, and then I press something on the keyboard, the system unit wakes up (I hear as coolers begin to turn), but the monitor does not react in any way.
I tried to disconnect and reconnect the HDMI cord, tried to inject EDID in config tried to change SMBIOS on MacMini8,1, but it did not change the situation.
How to solve the problem?
All in Mojave 10.14.6
Hi, I want to install MacOS Catalina on my laptop.
I was installed MacOS Mojave previously but i had a lot of problem, for example my wifi's card (Dell DW1820A) had a problem: My pc sometimes doesn't boot up or pc after some minutes crashed or slowed.
Now i want to try again to install macOS.
this is my spec:
CPU: i7 6500U with HD520
SSD: 500GB SSD Samsung
Wifi & Bluetooth: Dell DW1820A (Bluetooth: BCM2045A0) (Wifi: BCM94350ZAE)
Ethernet: Realtek 8100
Attached in this thread, my old clover configuration created by me (CLOVER OLD) and clover with Wifi driver (CLOVER) created by Hervè (I had asked help at insanelymac's community)
P.S SORRY FOR MY BAD ENGLISH.
Thanks in advance
HP 250 G5/Skylake/I5/520 graphics/sunrise point Insyde H20 updated with TPM, virtualizaton and secure boot disabled. 19A546d USB boots -v cpus=1 and begins install ok. After first reboot installer hangs at 14 minutes remaining with high CPU/fan use and no HDD write activity. Same after 4-5 hours. First reboot apparently creates the volume group and writes the installer files to the Data volume ok. Clover shows preboot/installer installer and Recovery icons. It appears that there are no system files being written to the System volume. The reboot USB verbose output screen indicates 'assertion failed 19A546d'. Mojave boots/runs ok on its own partition same HDD. Anyone with similar installer issue on HP notebook and/or Insyde BIOS? Any help appreciated.
Running Mojave 10.14.6 (18G95) on a Dell Precision 7510 and trying to get all framebuffers working properly.
The following CPU is being used: https://ark.intel.com/content/www/us/en/ark/products/89608/intel-xeon-processor-e3-1505m-v5-8m-cache-2-80-ghz.html
The actual Device ID of the iGPU is 0x191D.
There are the following graphical outputs:
Clover 5058 (update to date at time of writing) is being used and up to date versions of Lilu 1.38, WEG 1.3.1
Till now I've been running with the following config:
with Model Name: MacBookPro13,3
When using 191B:
LDVS - Ok
HDMI (no audio) : 1920x1080
Thunderbolt (no audio) : 3440 x 1440
191B-config-ioreg.zip is attached.
When using 1912:
No LDVS (as expected since this arrangement is targeted for iMac17,1
HDMI (with audio): 1920 x 1080
Thunderbolt (with audio) : 3440 x 1440
How can I get audio working as with 1912 on the 191B laptop config ?
I have everything working on my Acer notebook, except FN + Brightness keys using VoodoPS2Controller.kext
Now the brightness keys are "Pause+Break = Brightness Up" and "Fn+F12 = Brightness Down" working right now but they are not the actual keys.
The actual brightness keys are "Fn+RightArrow = Brightness Up" and "Fn+LeftArrow = Brightness Down" but they are not working.
The problem is I don't know the codes.
Installed ioio and enabled debugging to console:
Pause/Break is generating: "ApplePS2Keyboard: sending key e045=71" which upper the brightness
Fn+F12 is generating: "ApplePS2Keyboard: sending key 46=6b" which lower the brightness
Fn+RightArrow/LeftArrow generates nothing.
Keyboard attached to PS2K
Then I used rehabman's guide to enable ACPIDebugging, Installed kext to L/E, Debug methods (Instrument EC Queries, Add DSDT Debug Methods) to DSDT, but there are no codes generated to the log.
Attaching debug folder.
Also I don't know if it will help, but on Linux I got a code from decreasing/rising brightness with Fn+Left/RightArrow keys:
Fn+RightArrow: "0xe0 0x54 0xe0 0xd4"
Fn+Left: "0xe0 0x4c 0xe0 0xcc"
Also I love using EMlyDinEsH's SmartTouchpad Driver, with that all of my Fn keys are working except Brigtness keys ofc. If there are any fix I would like to use that with the smarttouchpad driver.
EMlyDinEsH's SmartTouchpad Driver: https://osxlatitude.com/forums/topic/1948-elan-focaltech-and-synaptics-smart-touchpad-driver-mac-os-x/
Specs in my signature.
Please help me fix this very last issue on my acer.