Jump to content
duduclx

[GUIDE] Dell Latitude E6410 Nvidia El Capitan Clover [ENG]

242 posts in this topic

Recommended Posts

This is totally off topic and should be addressed elsewhere but allow me clarify this: the WLAN/WWAN slots of these older Latitude laptops are mini PCIe/USB only, not mSATA. One must therefore be extremely cautious regarding the mini SSD cards that would installed. True mini PCIe SSDs are quite scarce these days (they also always tend to be PATA type, not SATA -i.e. much reduced performance- and of small capacity) and there is an unfortunate but sustained general confusion between mini PCIe and mSATA on the description of most advertised products. This very matter has been subject to substantial discussion all over the Net throughout the years, you can google for it, we're not going to renew this here...

 

So, mSATA SSDs will never be useable in these slots. True mini PCIe SSDs with on-board PATA or SATA controller are required. If you do find a mini PCIe (not mSATA) SSD of a decent size (say 128 to 256Go) with on-board SATA controller and at a reasonable price, please post the details. Many people will be interested. NB: you'll probably encounter mini SSD cards for Asus Eee PC but these fit an interface specific to those laptops.

 

Just to give you a recap:

E6x00 -> combo mini PCIe/USB slots only

E6x10 -> combo mini PCIe/USB slots only

E6x20 -> combo mini PCIe/USB slots only

E6x30 -> combo mini PCIe/USB slots only

E6x40 -> combo mini PCIe/USB/mSATA slots (1st time support for mSATA, undocumented by Dell)

 

I own a E6220, a E6230 and a E6440 so I can vouch for the above. One can only run an mSATA SSD on those older laptops with an adaptor off the standard SATA HDD slot or the expansion/optical disc bay.

 

and i can confirm that, i've found 128GB's but they are PATA/IDE, and all the advertised mPCIe SATA SSD's are mSata. And the sellers have used this confusion a lot, and still do. I was about to order from alibaba, and on the last second i noticed the msata in a different specs page, but the title did not mention it. Very unfortunate indeed, i cannot see the point of the absence of such technology.

 

MacBookPro6,2

Intel Core i5  2,4 GHz

4GB Ram

ST1000LM014-1EJ164 HDD

Dell NVS 3100M

Atheros 9285: 4.0.74.0-P2P

 

i had to install AtherosWiFiInjector.kext and IO80211Family.kext to activate WLAN i think there is the problem but i don't know where to patch in dsdt

 

Actually i meant the hardware specs from dell, there seem to be a few submodels of e6410, some have i7 some i5, some have nvidia gpu's and some dont. 

 

nvm, having a headache here and things are flying off me.

 

i'll PM you my dsdt laster as we seem to have a similar device (except wifi), also, are you using Clover right?

Share this post


Link to post
Share on other sites
Advertisement

and i can confirm that, i've found 128GB's but they are PATA/IDE, and all the advertised mPCIe SATA SSD's are mSata. And the sellers have used this confusion a lot, and still do. I was about to order from alibaba, and on the last second i noticed the msata in a different specs page, but the title did not mention it. Very unfortunate indeed, i cannot see the point of the absence of such technology.

 

 

Actually i meant the hardware specs from dell, there seem to be a few submodels of e6410, some have i7 some i5, some have nvidia gpu's and some dont.

 

nvm, having a headache here and things are flying off me.

 

i'll PM you my dsdt laster as we seem to have a similar device (except wifi), also, are you using Clover right?

yes i use clover the newest version.

 

If you have an AR9285-based card, you can patch your DSDT as detailed here to get the card to work OOB.

thanks for the info, i have WIFI working now. But still the same when i shut down everything turns of except Power LED and the FAN.

Restart is working fine.

Share this post


Link to post
Share on other sites

for shutdown, the dsdt patch is provided.

#Prepare to Sleep
into method label _PTS code_regex ([\s\S]*) replace_matched
begin
        If (LEqual (Arg0, 0x05))\n
        {\n
            Store (Zero, SLPE)\n
            Sleep (0x10)\n
        }\n
        Else\n
        {\n
            APTS (Arg0)\n
            EV5 (Arg0, Zero)\n
        }\n
end;

## DTGP
into method label DTGP remove_entry;
into definitionblock code_regex . insert
begin
Method (DTGP, 5, NotSerialized)\n
{\n
    If (LEqual (Arg0, Buffer (0x10)\n
            {\n
                /* 0000 */    0xC6, 0xB7, 0xB5, 0xA0, 0x18, 0x13, 0x1C, 0x44, \n
                /* 0008 */    0xB0, 0xC9, 0xFE, 0x69, 0x5E, 0xAF, 0x94, 0x9B\n
            }))\n
    {\n
        If (LEqual (Arg1, One))\n
        {\n
            If (LEqual (Arg2, Zero))\n
            {\n
                Store (Buffer (One)\n
                    {\n
                        0x03\n
                    }, Arg4)\n
                Return (One)\n
            }\n
            If (LEqual (Arg2, One))\n
            {\n
                Return (One)\n
            }\n
        }\n
    }\n
    Store (Buffer (One)\n
        {\n
            0x00\n
        }, Arg4)\n
    Return (Zero)\n
}\n
    OperationRegion (PMRS, SystemIO, 0x0430, One)\n
    Field (PMRS, ByteAcc, NoLock, Preserve)\n
    {\n
            ,   4, \n
        SLPE,   1 \n
    }\n
end;

also, all the patches have their importance.

you should read the guide before asking for something doesn't working.

 

cheers

Share this post


Link to post
Share on other sites

no eSata to test.

 

but it should.

 

have you tested it ?

 

cheers

Share this post


Link to post
Share on other sites

no eSata to test.

 

but it should.

 

have you tested it ?

 

cheers

 

Actually yes. It worked with injecting [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url]'s eSata generic kext.

Same with all my hacks. I will test with docking station eSata port and bet it will work too. 

Cheers.

Share this post


Link to post
Share on other sites

duduclx - thanks! I am typing this from my newish oldish E6410, all is working except audio. This is so amazing. I only spent $80 US on this thing, and moved my 8gb ram from my old beater C2D macbook pro. I call this an upgrade. Except for the audio, but I'll get there. I have other hackintoshes in the house, but this was my first laptop.

Share this post


Link to post
Share on other sites

audio may not working if you have update to 10.11.3 or above.

 

new patches is needed.

you surely can find them easily.

 

my dell E6410 will surely be sold.

i get a E6230.

both are my wife's computer.

 

me, have a HP 820 G2 and an desktop based on gigabyte motherboard.

 

i'll do a interactive coffee table soon, based on a dell optiplex 760 and dual boot android for pc and mac, with IR touch screen.

 

thanks for read and follow this guide.

cheers

Share this post


Link to post
Share on other sites

Thanks for all the guides. I got the audio to work, running 10.11.5. 

 

I have to say, the E6410 is an impressive little machine, but its trackpad and clicker are it's Achilles heel. I'd say it's the worst thing in terms of hardware on this laptop. But it's a fantastic value for anyone trying to hackintosh an i7 or i5 processor laptop.

Share this post


Link to post
Share on other sites

I sure would like to get my 6410 up and running. I started to tinker with it a while back when Mavericks was out and could never get it to boot the installer. Is there a boot package I need in order to get the USB to run and have a full functioning HackBook Pro like bellyface above.

Share this post


Link to post
Share on other sites

Blaggah, follow the steps at the beginning of the guide that duduclx drew up. As long as your E6410 has the nvidia GPU, I'd say it's perfectly doable. I totally doubted at first, but once I saw the apple glowing on that dinky dell, I knew it was possible. There were some hickups for me, keyboard and trackpad didn't work at all at OS X install stage, no issue I just plugged in a mouse and keyboard. In the end it all worked, but I ended up spending $10 on a broadcom wifi card off amazon.

 

It's doable, don't be afraid!

Share this post


Link to post
Share on other sites

bellyface, I'd have to check the laptop again tonight to see if it has the nvidia gpu.. As I'm sure it does but the only thing I remember is that it's the i5 model. I already swapped out the old hard drive to an SSD since I got it but really haven't put it to use..

Share this post


Link to post
Share on other sites

If it does not have the nVidia GPU, please note that the 1st gen Intel HD graphics of the E6410 cannot enjoy full graphics acceleration due to fitted eDP connector. That's unsupported by Apple on that iGPU. This makes the Intel HD E6410 a very poor (and, in my opinion, unworthy) Hackintosh as graphics are only partially supported.

Share this post


Link to post
Share on other sites

Ok i got almost everything to work on my dell but of course wifi no good.

just wondering is my broadcom wifi supported? if so how can i get it to work.

https://s32.postimg.org/mudv9ewat/Screen_Shot_2016_07_19_at_11_39_03_AM.png

https://s31.postimg.org/v6mh1ez1n/Screen_Shot_2016_07_19_at_12_01_13_PM.png

 

 if wifi card not supported is there any cheap wifi cards that will work with this laptop?   :)

Share this post


Link to post
Share on other sites

I checked and it does have the nvidia graphics on board. I left it to charge and probably attack it later on tonight if I get the chance.

Share this post


Link to post
Share on other sites

i have  installed macos sierra and got everything working on the laptop and is running perfect :thumbsup_anim:  the only thing i cant seem to get to fix is booting with out usb i had the same problem in el capitan with this laptop.   :wallbash:  i always get no bootable drive found anyone got any solution on what i'm doing wrong i did install clover in hard drive . :help:  please.

Share this post


Link to post
Share on other sites

LiquidKenpachi - Sounds like your clover install is not complete. Follow the steps exactly on what to check off in clover installer and be sure to select the new Sierra drive.

I installed sierra on one of my partitions on my macbook pro, loving what I see so far. 

Share this post


Link to post
Share on other sites

I managed to install El Capitan 10.11.3 last night and have yet to update it due to my wireless card not working. It keeps saying searching for network idk why it's happening.  I use those cards on all my laptop hackintoshes that support half mini wifi modules. It's the AR5B93, i bought about 30 of them in a lot for about $20 on ebay a few months back.

 

The things I noticed after post installation is that machine won't shut down and sleep doesn't work. If i manually sleep, it wakes right back up within a mili of a second. 

Share this post


Link to post
Share on other sites

Atheros AR5B93 works OOB in all recent or less recent OS X/Mac OS X versions, from SL to Sierra. You must have issues with your DSDT. Check that it does not contain a reference to another wifi card model. That would sure screw things up.

 

For the rest, well... I believe it's been discussed at great length in those 10pages.

Share this post


Link to post
Share on other sites

You may be right Hervé, I'll get down to it tomorrow. I have to get rid of the DSDT.

 

Is there a specific line I should look out for  in the DSDT for the wifi card? 

Share this post


Link to post
Share on other sites
Guest deactivated-2019-07-29

Hello. I have used this guide to install El Capitan on my E6410 with the NVS 3100M, the Intel Core i5, and two 2GB RAM cards, also using the config.plist from here and the DSDT.aml from here. The installation went fine, although it got stuck at "About a second remaining" for a long while. It did, however, eventually reboot the laptop. Afterwards, I deleted the DSDT.aml from the USB and replaced the config.plist with my own version (I took the version from /EFI/CLOVER in the pack, and used a different serial number). When loading back into Clover from the USB, the only entry is the El Capitan USB installer. I think that part of the issue is that I am using El Capitan version 10.11.6, as the installer had said it encountered an error while opening a file including the word "Update" and the phrase "10.11.6", however I do not remember the exact name. I have uploaded my config.plist. I would be very grateful for any and all help, thank you!

 

config.plist : https://drive.google.com/file/d/0B6fMfzYoSCJCc1pzYTkwc2Y4QTA

 

EDIT: Well, I guess I'll try my backup of the 10.11.1 installer. Let's see how this goes!

 

EDIT2: Storing the installer on a Windows FS definitely was not a good idea, as now the installer warns that it can not find the installation application. Oh well, back to the drawing board...

 

EDIT3: I suppose I'll try the Yosemite installer. There's nowhere to go but up! But it sure would be easier to go up with a little help... :(

 

EDIT4: I haven't tried Yosemite yet, but I have tried El Capitan 10.11.4. After the installation, I replaced the EFI folder on my USB with the one from the pack. It still did not show the internal hard drive as a bootable volume. I think my computer has some issues.

 

EDIT5: I suppose I'll switch back to Windows, for now. Every computer I try to hackintosh ends up like this (except my D620, for some reason)... it's like Apple doesn't want me installing their OS on non-Apple software! Crazy! I hope I get help eventually, though. Because I will wait forever.

 

EDIT6: I've been getting more help on a thread I created on OSXLATITUDE, found here. If anyone has the same problem as me, be sure to look there! :)

Share this post


Link to post
Share on other sites

HI Guys (and Girls ?)!

 

Long time no action from my side but am going to try to upgrade 2 E6410 machines (one i5 and one i7) from el capitan to Sierra; I did it as per description on another popular osx site of a guy named Tony  :) but it led to panics in the beginning.

 

Dudu or Hervé; Are you guys in for it to update this guide or is it too much work ? Can I be of any assistance ?

 

Salut from Holland,

 

Bart

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By tonyx86
      This thread for installing Catalina on the Dell Latitude E6410 WITH NVIDIA GRAPHICS (BIOS A17, NVidia 3100m) will help you install a fresh installation of Catalina on your Dell Latitude E6410 and it will also help you upgrade from Mojave 10.14.6 if you have already installed Mojave by following the instructions here.  The instructions in this first post assume that you are installing Catalina in an APFS container.  If you are curious about the evolution of this solution and how sleep/wake was solved, review the Mojave installation thread.
       
      Important: This Thread is NOT intended to help you install macOS on a Latitude E6410 with Intel HD Graphics (without Nvidia graphics).  The DSDT attached to this first post (in E6410-Catalina.zip) is VERY SPECIFIC to the Nvidia graphics implementation and has not been edited for HD Graphics - there are elements required for HD Graphics that are missing from the attached DSDT and there are DSDT mods that have not been tested with HD Graphics.  Also, the kexts attached to this first post are specific to a Broadcom Wi-Fi card which must replace the original Intel Wi-Fi card.
       
      This first post will be modified to reflect lessons learned and to reflect the most current working state of my Latitude E6410 (with NVidia 3100m discrete graphics) running Catalina.  Issues, observations and performance tips are recorded toward the bottom of this first post.  My recommended CLOVER configuration is specified toward the bottom of this first post.
       
      My system is as follows:
      Dell Latitude E6410 (I7-620m, Nvidia 3100M, 8GB DDR3, 512GB SSD, 1440x900 display, BIOS: A17) Wi-Fi: Broadcom BCM 94352HMB (replaced original Wi-Fi card) BIOS (version A17) configured as follows (leave default unless listed here): Boot Sequence: USB, Internal HDD, CD/DVD, Modular Bay HDD; Boot List Option: Legacy; Integrated NIC:Enabled; Parallel Port: Disabled; Serial Port: Disabled; SATA Operation: AHCI; Misc Devices: Enable Modular Bay, Camera, External USB, Microphone, Media Card and 1394; Latitude ON Reader: Disabled; Keyboard Illumination: Auto ALS and Input; Ambient Light Sensor: Enabled; OROM Keyboard Access: Disable; TPM Security: Disable; Computrace:Deactivate; CPU XD Support: Enable; Performance: Enable all options; Power Management: Disable Wake on AC, Disable Wake on LAN/WAN, Express Charge: Standard, Charge Behavior: Enabled; Keypad: Fn Key Only; Mouse/Touchpad: Touchpad/PS-2 Mouse; USB Emulation: Enable Legacy; Fn Key Emulation: Disabled; Fastboot: Thorough; Virtualization: Enable Intel Virtualization, Disable VT for Direct I/O, Disable Trusted Execution; Wireless Switch: Bluetooth and WLAN; Wireless Device Enable: Bluetooth and WLAN;   
      Versions of the software used in this installation are listed below the installation steps.  EFI and kexts for Catalina are attached to this first post in E6410-Catalina.zip.  CLOVER configuration is specified below the installation steps.
       
      Steps to install Catalina on a Dell Latitude E6410 (BIOS A17, NVidia 3100m)
      If performing an upgrade from Mojave, backup your Mojave disk! (Carbon Copy or similar) Download Catalina Installer Download DosDude Catalina Patcher Use DosDude Patcher to create Catalina USB Installer Delete LegacyUSBInjector.kext (we're using @RehabMan's USBInjectAll.kext with custom SSDT) and delete SIPManager.kext (CLOVER is managing SIP) from Catalina USB Installer's /Library/Extensions folder Copy all but the FakeSMC sensor kexts in E6410-Catalina.zip (attached) LE folder to the Catalina USB Installer /Library/Extensions (copy all kexts (including FakeSMC.kext) but not the FakeSMC sensor kexts) Install CLOVER Bootloader (Legacy) on USB Installer using the EFI in the E6410-Catalina.zip (attached).  Use the CLOVER configuration specified below.  Be sure to replace the *** MASKED *** parameters in the attached config.plist with your own values. Boot your Latitude E6410 from the Catalina USB Installer that you created in steps 4-7. Select "Reinstall macOS" (note that I have existing installations of Mojave and High Sierra on my Latitude E6410, so it's possible that this menu item changes to "Install macOS" if you don't have any previous macOS installations). Select your Catalina destination partition (which will be your Mojave partition if you are upgrading) After the Catalina Installer reboots the first time, boot from the "macOS Installer" partition on the disk that you selected as your Catalina destination (not the macOS installer on the USB) After the Catalina Installer reboots the second time, boot the Catalina macOS Installer on the USB Select the Post Install Patcher utility Select only the following Post Install Patches (no other patches / options) Install Patch Updater Legacy Video After the Post Install Patcher reboots,  boot from the newly installed (or upgraded) Catalina partition and complete the macOS configuration Remove these kexts (if they exist) from /Library/Extensions: LegacyUSBInjector.kext, LegacyUSBVideoSupport.kext and SIPManager.kext If you are performing a fresh installation of Catalina: Install CLOVER on your boot disk and configure EFI using files in the attached E6410-Catalina.zip.  Use the CLOVER configuration below.  Your EFI Clover/kexts/Other folder needs only FakeSMC.kext, IntelMausiEthernet.kext, USBInjectAll.kext and VoodooPS2.kext.  Be sure to replace the *** MASKED *** parameters in the attached config.plist with your own values. Install all kexts in the attached E6410-Catalina.zip LE folder to your /Library/Extensions folder.  NOTE: These instructions assume installation of Brcm kexts in /Library/Extensions.  Read the Brcm install instructions if you're installing kexts in EFI/Clover/kexts/Other, since your installation and at least one kext WILL BE DIFFERENT. Copy HWMonitor from the application folder in the attached E6410-Catalina.zip to your Applications folder. Install VoodooHDA (I installed using the Classic method) If you are upgrading from Mojave that you installed using the instructions here: Update Lilu.kext and replace BrcmFirmwareRepo.kext and BrcmPatchRAM2.kext (in /Library/Extensions) with latest BrcmBluetoothInjector.kext, BrcmFirmwareRepo.kext and BrcmPatchRAM3.kext. NOTE: These instructions assume installation of Brcm kexts in /Library/Extensions.  Read the Brcm install instructions if you're installing kexts in EFI/Clover/kexts/Other, since your installation and at least one kext WILL BE DIFFERENT. Update IntelMausiEthernet.kext Remove VoodooSDHC.kext from /Library/Extensions If you're manually installing kexts in /Library/Extensions, make sure that you 'sudo chown -R root:wheel *.kext' and 'sudo chmod -R 755 *.kext' the kexts in /Library/Extensions and you execute 'sudo kextcache -i /'.  After you execute 'sudo kextcache -i /' you should observe that ALL kexts are allowed.  If not, your install is not complete. Reboot from your new/upgraded Catalina partition Welcome to macOS Catalina! Change the keyboard type to ISO (System Preferences > Keyboard > Change Keyboard Type) Swap the Command and Option keys (System Preferences > Keyboard > Modifier Keys)  
      Version Info at the time of this writing:
      Catalina Installer 10.15.2 CLOVER v2.5k r5102 DosDude Catalina Patcher: v1.3.0 Lilu.kext 1.4.0 BrcmFirmwareRepo.kext 2.5.0 BrcmBluetoothInjector.kext 2.5.0 BrcmPatchRAM3.kext 2.5.0 IntelMausiEthernet.kext 2.5.0
      VoodooHDA.kext 2.9.2
       
      What is not working (that was working in Mojave)
      SD Card Slot (had to remove VoodooSDHC.kext which caused system freeze on wake)  
      Known Issues and Their Solutions
      (No solution yet) No SD Card Slot (had to remove VoodooSDHC.kext) - I read somewhere that there is a solution that does not require any kexts (just a DSDT edit).  Haven't yet implemented this fix. (Not a problem that needs to be solved - leaving for historical purposes.  I am running Catalina without this.) - IOHWControl does not load under GFX0 (as observed in IORegistryExplorer).  Solution (if it needs to be solved) is to install AppleHWSensor.kext from a DosDude-patched Mojave /S/L/E in Catalina's /L/E.  Copy and install your own or use the kext attached to this post. (Solved - no further work required) External USB ports do not work after waking from sleep (S3) - Upgrade Lilu.kext and replace BrcmFirmwareRepo.kext and BrcmPatchRAM2.kext (in /L/E) with latest BrcmBluetoothInjector.kext, BrcmFirmwareRepo.kext and BrcmPatchRAM3.kext. (Solved - no further work required) Boot and shut-down time of Catalina is slower than Mojave - Upgrade Lilu.kext and replace BrcmFirmwareRepo.kext and BrcmPatchRAM2.kext (in /L/E) with latest BrcmBluetoothInjector.kext, BrcmFirmwareRepo.kext and BrcmPatchRAM3.kext. (Solved - no further work required) Wi-Fi is not immediately available at OS startup - Upgrade Lilu.kext and replace BrcmFirmwareRepo.kext and BrcmPatchRAM2.kext (in /L/E) with latest BrcmBluetoothInjector.kext, BrcmFirmwareRepo.kext and BrcmPatchRAM3.kext. (Solved - no further work required) Laptop freezes on wake - Remove VoodooSDHC.kext from /Library/Extensions  
      Tips for Improved Performance (on this and other older systems)
      System Preferences > Spotlight > Search Results: Uncheck all options System Preferences > Spotlight > Privacy: Add all Volumes System Preferences > Accessibility > Display: Check "Reduce motion" System Preferences > Accessibility > Display: Check "Reduce transparency"  
      Other tips
      If your fan is always running and temps are good, try pressing Fn + z (I haven't noticed this issue for a while since I completed DSDT edits for Mojave, but keeping this here for historical purposes)  
      CLOVER Installation: Use these configuration options
      Install Clover in the ESP Boot Sectors Install boot0af in MBR Clover for BIOS (legacy) booting Clover EFI 64-bits SATA BIOS Drivers, 64-bit Recommended drivers FSInject File System drivers ApfsDriverLoader Install RC scripts on target volume Themes Choose your desired theme Install Clover Preference Pane After clicking "Continue", if prompted with "This Clover package is incompatible with this version of macOS," install anyway  
      After CLOVER installation is complete Copy the following from the attached E6410-Catalina.zip ACPI patched contents config.plist (change *** MASKED *** values to your own) kexts/Other (remove all other kext folders) Remove christmas and new year folders from themes (if present)  
      Credits
      Thanks to those who contributed to my Mojave solution and to the DosDude team (for the incredible macOS patchers), I think this Catalina installation was the easiest macOS installation that I have experienced (so far).  Many thanks to @Slice and his team for the incredible work on CLOVER and for continuing to support old legacy systems like this.  Also, thanks to @headkaze, @vit9696 and others I'm sure for maintaining the Brcm kexts.
       
       
      E6410-Catalina.zip


      AppleHWSensor.kext.zip
    • By Tushark2
      Hello,
      1st my laptop spec. 
      CPU - 2.53 GHz Intel Core i3 380m
      RAM - 6 GB 1333 MHz DDR3
      GPU -  1st gen Intel HD Graphics 288 MB
      Laptop - Dell Vostro 3500 series
      BT/WIFI - AzureWave BCM94352HMB
       
      I installed Olarila Mojave 10.14.6 and managed to install 1st gen intel HD graphics but it was bit laggy bcos this gnu doest support metal and its a old machine, so I decided to move to Olarila High Sierra.
      I installed it with most of things working fine expect some issues, for that I want to make SSDT and DSDT to make it run without glitches.
       
      I am atteching my sendme.zip , can some take a look to my current settings and suggest me some changes  
      (Olarila down from few days for me )
       
      Send me MacBook-Pro.zip
    • By tlefko
      Now updated for 10.13.6+ Designed for i7 Skylake, QHD+, 256/8GB memory
      https://github.com/tlefko/OSX-XPS13-9350
      INSTALL
      you may want to disable Configure BIOS settings for EFI Booting. Disable RAID, enable AHCI, virtualization, make sure VRAM is over 32. and you should be set. also disable secure boot and enable UEFI booting You should create an EFI folder onto the USB and copy the contents of the USB onto the drive Boot off the usb using external mouse/keyboard (if required) and follow the installer prompts boot off the MAC HDD NOTES
      You may want to remove the DSDT patches if you have an issue. and manually repatch. however if you have the same model it should not be an issue. POST INSTALL
      Copy the folders from the root of the USB onto the computer efi folder. NOTES
      Some sleep bugs Tested with 10.13.6, not with 10.14 DSDT patches may have an issues if not the same model, you can remove them if there is an issue. CREDITS
      @Rehabman @maz-1 @syscl @darkvoid SUPPORT
      feel free to ask questions / open answers, you can also check out my other repository covering a previous mac version for the same model for other files for that / information on this topic Files.zip
    • By kingoffright
      Dear all,
       
      I have a external harddisk about 500GB, I installed the clover into it and the harddisk is GPT format, below is the 3 partitions details:
      FS01: EFI - disk0s1 - fat32
      FS02: install mac  image - disk0s2 -  hfs+
      FS03: install windows 10 - disk0s3 - fat32
       
      I can use this external harddisk to install Mac without issue, I use below steps to install windows 10
      enter the FS03:
      cd to efi/boot/ and excuete bootx64.efi
      after pop up the windows install screen, i click next and it shows error 'A media driver your computer needs is missing...' and the installation can not go any further.
      Firstly I use ultraiso to write the windows 10 image to a flash disk and no issue to start install window 10 so the image is working fine. Since I dont know how to write
      a wiindow installation image into harddisk partition, I used winrar extra all the files into disk0s3, am I missing some steps or actually clover not support to install windows
      by partitions, apprecating any helps.
       
×