Jump to content
chatdeau

HP Z400/Z600/Z800 Workstations OS X 10.10.x/10.11.x Installation

1,317 posts in this topic

Recommended Posts

Great

Have you boot without -x and you haven't any problem with freezes in finder?

Yes. Booted as above without -x and NV_Disable.

 

No issues other than installing the drivers.

Network worked out of box (AppleBCM5701Ethernet.kext) and Graphics (NVDANV50HAL).

 

RAM is reporting wrong amount. Easy fix.

No USB issues.

No Freezes in Finder associated with chipset.

 

Used sil3132.kext from Sonnet to get past legacy AHCI issue. Still troubleshooting that. This may be the cause of finder freezes others are experiencing.

 

I'll report back if I make some headway.

 

01f8c399d27a24492dc2c3ecde7e53ff.jpg

Share this post


Link to post
Share on other sites
Advertisement

OK - I'm 100% running now without issues on 10.11.3!   :thumbsup_anim:

 

Various issues fixed with DSDT (including Intel ESB2 AHCI).

 

My advice is to wait to install DSDT though, only after successful usb install (don't use it on USB extra).

 

Attached you'll see my extra folder. Please disregard sil3132.kext if you don't have that hardware.

 

Keep me posted if anyone gets this working with Clover.

 

Thanks,

 

http://browser.primatelabs.com/geekbench3/5202019

 

Extra.zip

Share this post


Link to post
Share on other sites

OK - I'm 100% running now without issues on 10.11.3!   :thumbsup_anim:

 

Various issues fixed with DSDT (including Intel ESB2 AHCI).

 

My advice is to wait to install DSDT though, only after successful usb install (don't use it on USB extra).

 

Attached you'll see my extra folder. Please disregard sil3132.kext if you don't have that hardware.

 

Keep me posted if anyone gets this working with Clover.

 

Thanks,

 

http://browser.primatelabs.com/geekbench3/5202019

 

attachicon.gifExtra.zip

ok thanks

i will try it

 

Can you make a mini guide with the steps so me and others can install ?

Thanks A lot :)  :)  :)  :)

Share this post


Link to post
Share on other sites

hi djfremen  did you connect a separate sata controller

SiliconImage3132?

Yes. initially I used this card:

 

post-390501-0-67532800-1455047367_thumb.png

 

It's disconnected now though. Use whatever tool is free to get 10.11.3 installed on your target. A real mac would work perfect too.

 

Will try to make a compete write soon but Enoch is the key.

Share this post


Link to post
Share on other sites

Yes. initially I used this card:

 

attachicon.gifScreen Shot 2016-02-09 at 11.42.59 AM.png

 

It's disconnected now though. Use whatever tool is free to get 10.11.3 installed on your target. A real mac would work perfect too.

 

Will try to make a compete write soon but Enoch is the key.

Hi,

 

Do you have audio working as well?

 

Thanks for the great work!

 

-apav

Share this post


Link to post
Share on other sites

Hi,

 

Do you have audio working as well?

 

Thanks for the great work!

 

-apav

 

No love on Audio. I tried the kexts on this thread. AppleHDA is still loading even though I have the disabler in there.

Share this post


Link to post
Share on other sites

I have istall el capitan 10.11.2 with enoch and djfremen guide but i have the same problem again many freezes in finder  :(

i don't know where is the problem

my configurastion is:

2 x xeon 5660

nvidia titan

48 gb ram 

 

i boot with -f and - v only

Share this post


Link to post
Share on other sites

I have istall el capitan 10.11.2 with enoch and djfremen guide but i have the same problem again many freezes in finder :(

i don't know where is the problem

my configurastion is:

2 x xeon 5660

nvidia titan

48 gb ram

 

i boot with -f and - v only

Please tell us what your system console is saying when it "freezes"

 

I hate that term because it can mean several things (kernel panic in finder, mouse lag, complete lock-up). Please be specific which you're experiencing. Also, why did you build a key with 10.11.2 and not the current download of 10.11.3? I'd recommend using the latest. Is your Nvidia Titan fully supported?

Share this post


Link to post
Share on other sites

hi Guys i got it El Capi on z800 with clover

all the credit gose to Chris 1111 and clover team :thumbsup_anim::thumbsup_anim::thumbsup_anim::thumbsup_anim:

Nice! Please briefly describe the process and boot flags for others here.

 

Thanks.

Share this post


Link to post
Share on other sites

i asked for some feedback but nothing happened so that,s why the post is gone


if the people want a good working system then we have to work together and help each other

Share this post


Link to post
Share on other sites

as i said if you need any help most welcome i'm just interested in graphic how it work for other

 

 

 

 

Clover  config.plist and kext that i use

I will try too today.

Share this post


Link to post
Share on other sites

Hey Rockey,

 

I used to run 10.9.5 without problems year ago on z800 I am running windows server on it now but your post gives me hope to try El-Capitan.  Any instructions how to install everything I always used the Chameleon guide ... never used Clover ... what are the steps?  What graphics card do you have I will be trying with ATI 7970.

 

Thanks

Share this post


Link to post
Share on other sites

Hey Rockey,

 

I used to run 10.9.5 without problems year ago on z800 I am running windows server on it now but your post gives me hope to try El-Capitan. Any instructions how to install everything I always used the Chameleon guide ... never used Clover ... what are the steps? What graphics card do you have I will be trying with ATI 7970.

 

Thanks

This should help:

 

http://www.insanelymac.com/forum/topic/307003-clover-os-x-el-capitan-usb/

Share this post


Link to post
Share on other sites

I have a hp Z400 with 6 mem slots, xeon w3520, 8gb ddr3 ecc, hgst 250gb and Ati radeon 6870.

 

I have Installed the latest bios 3.57.

 

I have 2 successful virtual machines installation vbox with Yosemite and VmWare with El Capitain working as guests at w7x64 ult oem hp win host os.

 

I tried many (> 20) times to install El Cap or Yosemite on hdd.

 

The furthest i have got is kernel panic that looks like for me. It looks like when everything is loaded and cpu wants to start protected mode or gui or installation program everything fails an i got following memory dump as pictured here: http://tinypic.com/r/23vhyf6/9

 

I tried all what i could think of in combination of CLOVER flags and bios settings but still cannot make any progress.

 

Tried to be as restrictive as I could but always exactly the same result.

 

It must be that i am doing something really wrong since I cannot see even Installer running.

 

Any help is welcome :)

 

I followed all that i could find in this post or some other places on the internet but w/o any success :(

 

Any suggestions?

 

I feel very frustrated and dumb....

 

I do not have any experience with any OS X, however i do have some exp with windows from 3.11 to 7 :)

as well as some Linux experience. It looks like it did not help at all...

 

Thanks in adv! :)

 

 

 

 

 

Share this post


Link to post
Share on other sites

I have a hp Z400 with 6 mem slots, xeon w3520, 8gb ddr3 ecc, hgst 250gb and Ati radeon 6870.

 

I have Installed the latest bios 3.57.

 

I have 2 successful virtual machines installation vbox with Yosemite and VmWare with El Capitain working as guests at w7x64 ult oem hp win host os.

 

I tried many (> 20) times to install El Cap or Yosemite on hdd.

 

The furthest i have got is kernel panic that looks like for me. It looks like when everything is loaded and cpu wants to start protected mode or gui or installation program everything fails an i got following memory dump as pictured here: http://tinypic.com/r/23vhyf6/9

 

I tried all what i could think of in combination of CLOVER flags and bios settings but still cannot make any progress.

 

Tried to be as restrictive as I could but always exactly the same result.

 

It must be that i am doing something really wrong since I cannot see even Installer running.

 

Any help is welcome :)

 

I followed all that i could find in this post or some other places on the internet but w/o any success :(

 

Any suggestions?

 

I feel very frustrated and dumb....

 

I do not have any experience with any OS X, however i do have some exp with windows from 3.11 to 7 :)

as well as some Linux experience. It looks like it did not help at all...

 

Thanks in adv! :)

I am not aware of anyone who has been able to install El Capitan on an HP Z400 using Clover. It has been done using Enoch Chameleon.

Share this post


Link to post
Share on other sites

Rocky12,  Thanks much for your help. I tried to create usb drive with dell precision clover tool however it says that i don't have .app either for yosemite or el capt...

 

I am also not familiar at all with OS X lingo - jargon so, i am not sure about dsdt, config.plist, ...

 

I would be fine with installation Yosemite or El Capt on z400, does not to be any specific, why did readers conclude that I am asking for El Capt, Thread is called Yosemite..

 

Is there any complete idiot-proof description (straight algorithm) of how to do things without much referencing to other posts, because they also reference to someones else post.

 

After 2. and 3. reference I am lost. 

 

It could be any Os Yose or Elcap.

 

any bootoader that works

 

any parameters that i need to enter - change either before, or after installation of os, boot loader, ...

 

I do have a nVidia quadro that i can put into machine in case (i am not sure for the model now) in case OS X cannot install/start with radeon 6870.

 

So please, be patient and clear as much as possible.

 

10x a lot!

Share this post


Link to post
Share on other sites

Rocky12,  Thanks much for your help. I tried to create usb drive with dell precision clover tool however it says that i don't have .app either for yosemite or el capt...

 

I am also not familiar at all with OS X lingo - jargon so, i am not sure about dsdt, config.plist, ...

 

I would be fine with installation Yosemite or El Capt on z400, does not to be any specific, why did readers conclude that I am asking for El Capt, Thread is called Yosemite..

 

Is there any complete idiot-proof description (straight algorithm) of how to do things without much referencing to other posts, because they also reference to someones else post.

 

After 2. and 3. reference I am lost. 

 

It could be any Os Yose or Elcap.

 

any bootoader that works

 

any parameters that i need to enter - change either before, or after installation of os, boot loader, ...

 

I do have a nVidia quadro that i can put into machine in case (i am not sure for the model now) in case OS X cannot install/start with radeon 6870.

 

So please, be patient and clear as much as possible.

 

10x a lot!

You mentioned El Cap in your initial post and also in this post even though the thread is about installing Yosemite.

Share this post


Link to post
Share on other sites

did u download OSX app from app store if not u have to download without any osx app u cannot make usb installer

 

dear friend jaymack it doesn't make any difference yosemite or El Cap the only thing is to change the boot flag

Share this post


Link to post
Share on other sites

I did. I have two different apps Yosemite and El Capitain.

 

Here is my DSDT fiel in the attachment.

 

I hope it will say more than my words.. :)

 

If i need to submit any other file to clarify further my situation please tell me what i need to upload

and also where is usually located so i can find it.

 

10x a lot!

 

 

DSDT.zip

Share this post


Link to post
Share on other sites

this is my own experience on yosemite and El Cap if u think ur method is batter then i am kindly requesting you to explain how to without dsdt with clover

this is ur patched dsdt

Clover has never worked for me on my HP Z400. I used Chameleon for Mavericks and Yosemite, and Enoch Chameleon for El Capitan. I haven't seen an installation of El Capitan on an HP Z400 using Clover.

Share this post


Link to post
Share on other sites

Clover has never worked for me on my HP Z400. I used Chameleon for Mavericks and Yosemite, and Enoch Chameleon for El Capitan. I haven't seen an installation of El Capitan on an HP Z400 using Clover.

Does anyone have audio working on El Capitan on a z400?  Theres no reason for me to move from Yosemite to El Capitan unless audio is fully working.

 

Thanks

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By gengik84
      Ciro82==>>Thanks
      Uno dei tre Requisiti:
      Hack funzionante Mac vero Macchina virtuale Impostazioni Bios per il boot:
      Cercate una voce  del tipo “Sata Mode”e settatela  in AHCI
      Secure Boot: disabilitare o altri sistemi operativi
      CSM: UEFI o LEGACY, oppure a secondo del tipo di installazione
      VT-x / VT-d disable
      *Nota: Secure boot e csm valido solo per bios UEFI
      Materiale Occorrente 
      "OS X (Versione App.Store)”
      USB 8GB  *nota: nel caso di usb superiori dovrà essere partizionata, in modo da avere una partizione su cui "lavoreremo,di questa dimensione
      ShowAllfiles 
      kext Wizard 
      Bootloader Clover_2.3k_r xxx:                   http: //sourceforge.n.../cloverefiboot/
      Clover Configurator:                                    http: //mackie100proj...a.org/download/
      FakeSmc.kext:                                            https://github.com/kozlek/HWSensors/releases
      In allegato,a fondo pagina troverete un "pacchetto" contenente : ShowAllfiles, Kext Wizard, FakeSmc.kext: 
      App alternative:
      ESP Mounter Pro: per montare la partizione EFI
      Vi illustrerò tre metodi per creare la usb, ma sono ben distinti… quindi usatene soltanto uno
      Metodo 1: “Install Mac_OS_X.command” Metodo 2: “Create Install Media di Apple” Metodo 3:  Metodo Manuale Alla fine delle preparazione dell’installer, tutti i metodi necessitano l’installazione del Bootloader Clover sulla a vostra USB.
      “CONDIZIONI OBBLIGATORIE”
      PUNTO 1: che la vostra usb sia stata preventivamente nominata USB (caratteri maiuscoli) Tabella di partizione GUID e la formattazione in  Mac esteso Journaled.
      PUNTO 2: che l’installer di OSX si trovi in Applicazioni
      Utility Disco 
      Selezionate la pendrive, andate su “partizione”, selezionate “1 partizione”, impostate Mac OS esteso journaled e date il nome USB, poi in basso cliccate su opzioni e scegliete Tabella partizione (GUID), poi “applica”.
      Immagine 
      Riporto nuovamente l’operazione sopra citata adoperando dal nuovo Utility Disco introdotto su El Capitan.
      Rimane ovviamente invariato nome della usb in ==>> USB (maiuscolo), la formattazione in Mac esteso Journaled e sia la mappa partizione in GUID
      Da utility disco selezionate la usb, cliccate su inizializza.
      dal menù a tendina scegliete la relative impostazioni
      Immagine  
      Procedura effettua da High Sierra è la stessa della precedente, l'unica attenzione e operazione da aggiungere in primis  è cliccare nel menù a tendina in alto sulla sinistra di utility disco e selezionare "mostra tutti i dispositivi"
      Immagine 
       
      =====================
        METODO 1: "Install_Mac_OS_X.Command" Lo script che trovate allegato in fondo alla guida permette la creazione dell’installer in maniera automatica
      Include la possibilità di scelta di tre versioni di osx
      Yosemite El Capitan Sierra Il risultato finale è come quello del metodo "manuale" descritto nella guida, per cui l'installazione avverrà in un solo passaggio, non in due come con il metodo createinstallmedia. 
      Offre inoltre la possibilità di inserire un kernel patchato, utile, per esempio, per chi usa AMD.
      Rimane invariato il nome dato alla usb in USB, mappa partizione e tipo di formattazione
      Se la vostra usb non sarà rinominata nel modo corretto, verrete avvisati dal terminale, quindi non dovrete far altro che apportare la relativa modifica e rilanciare nuovamente lo script
      Esempio
      ===========================
      Metodo 2 
      L'intento è quello di usare la procedura fornitaci direttamente da Apple, "createinstallmedia", introdotta  con Mavericks. 
      Tale metodo prevede l’uso del terminale che via via se ne sta perdendo il “valore e l’uso”
      Inizialmente per i neofiti potrà sembrare problematico ma alla fine non è così.
      Durante il post installazione alcune operazioni ne richiedono l’ uso.
      Perciò mi sono chiesto perchè, qualora uno volesse, non far conoscere da subito un po’ questo “strumento”???
      Per favorirvi vi ho allegato i comandi già  “pronti”, i quali li potrete copiare ed incollare sul terminale.
      A questo punto aprite il terminale, copiate ed incollate il comando sottostante e premete invio, digitate la vostra password e premete nuovamente invio.
      Comando per creare USB con Yosemite:
      sudo /Applications/Install\ OS\ X\ Yosemite.app/Contents/Resources/createinstallmedia --volume /Volumes/USB --applicationpath /Applications/Install\ OS\ X\ Yosemite.app --nointeraction  
      Comando per creare USB con El Capitan
      sudo /Applications/Install\ OS\ X\ El\ Capitan.app/Contents/Resources/createinstallmedia --volume /Volumes/USB --applicationpath /Applications/Install\ OS\ X\ El\ Capitan.app --nointeraction Comando per creare USB con Sierra 
      sudo /Applications/Install\ macOS\ Sierra.app/Contents/Resources/createinstallmedia --volume /Volumes/USB --applicationpath /Applications/Install\ macOS\ Sierra.app/ --nointeraction Per creare USB con Hight Sierra o Mojave usate --> C_I_M (aggiornato per 10.14)
       
      Funziona con il drag & drop sul terminale, in questo caso non vi è necessità che la usb sia nominata in un determinato modo ed essendo basato su create install media ovviamente funziona da 10.9 a 10.14.... 
      BENE…IL PROCESSO DI CREAZIONE E’ INIZIATO…
      AVREMO CIRCA 20/30 MINUTI DI TEMPO LIBERO A CUI DEDICARSI A CIO’ CHE VOGLIAMO………………………………………..  
      COLGO L’OCCASIONE PER FARVI NOTARE LA VELOCITA’ E LA SICUREZZA DI QUESTO METODO
      CONFRONTATE QUESTO CON IL TERZO METODO E NOTERETE CHE CON UN SOLO PASSAGGIO, OSSIA IL COMANDO DATO AL TERMINALE, FACCIAMO IN UNA SINGOLA OPERAZIONE TUTTI I VARI STEP DESCRITTI SULL’ ALTRO METODO.
      DETTO QUESTO, MOLTO IMPORTANTE E’ SOTTOLINEARE CHE COSI’ FACENDO EVITEREMO ERRORI  DI DISTRAZIONE RIGUARDO AI PASSAGGI O FRAINTENDIMENTI.
      Immagine 
      Potete adesso passare ad installare il bootloader Clover sulla vostra usb.
      *NOTA*:
      Avendo usato questo metodo l'installazione si dividerà in due fasi, perciò dopo il primo riavvio e necessario far partire nuovamente l'installer, selezionare lo stesso disco senza formattarlo.
      Finita questa ulteriore fase , l'installazione sarà terminata
      =========================
      METODO "MANUALE"....  (lascio per futura memoria-Compatibile fino a 10.12)
      ==========================
      Bootloader
      **Nota:** Installazione in UEFI  dipenderà dalla scheda madre in vostro possesso, quindi se non supporta tale opzione , il bootloader dovrà essere installato in  modalità Legacy.
       Vi invito, qualora non sapeste questa informazione, a recarvi nel sito ufficiale del produttore e controllare le informazioni a riguardo
      Fatto questo dobbiamo installare  Clover sulla usb.
      A seconda del tipo di Bios o al tipo di installazione che vogliamo fare UEFI o Legacy avremo ovviamente configurazioni diverse in questa fase.
      Lanciate il pkg.
      Immagine 

       
      Cambiate la destinazione di installazione ad USB oppure Install Mac_OS_X (a secondo del tipo di creazione eseguita)
      Successivamente clicchiamo su "Ad Hoc"
      Per Installazione UEFI
      Mettete i flag   : Installazione solo per avvio UEFI
                               : installare Clover nella ESP
                               : Driver64UEFI  AptioMemory --> (consigliato) 
                               : Driver64UEFI  ApfsDriverLoader --> (consigliato) --> sostituisce l'uso del driver apfs.efi
                               : Selezionate l'altri driver come da successiva immagine,
       
      *Nota: Altri driver che si possono usare  al suo posto  sono:
       informazioni 
       
      Proseguite con l’installazione.
      Immagine 
      ** Ricordate che avrete accesso a questa cartella dopo aver montato la partizione EFI**
      ===========================
      Per installazione Legacy
      Immagine 
      ===========================
      Impostazione per config.plist:
      Con clover configurator “montate” la partizione EFI della usb.
      1) Per fare questo nel menù di sinistra, cliccate su “Mount EFI”
      2) individuate la partizione relativa alla vostra usb, a questo punto montiamo la relativa partizione EFI  selezionando l’apposito pulsante “Mount Partition”
      Immagine 
      3) Successivamente cliccate su “Open Partition”.. recatevi in EFI/Clover ed aprite il config.plist
      4) Sezione ACPI: Disabilitate tutti i fix sia del menù 1 che del menù 2
      Immagine 
      5) Sezione BOOT: Sole se si sta installando Yosemite mettete il flag su kext-dev-mode=1
      Immagine 
      6) Sezione RT Variables: Se si sta installando El Capitan oppure Sierra, aggiungere i valori: BooterConfig= 0x28, CsrActiveConfig= 0x67
      Immagine 
      7) Sezione System Parameters: Su inject kext mettete YES
      Immagine 
      ===========================
      Nota: Su El Capitan, è stato introdotto SIP (System Integrity Protection)
      Info:
      ===========================
      Recatevi in EFI/Clover/kext/10.x 
      X= alla versione di osx che state installando. Per esempio se installerete Yosemite dovrete recarvi nella cartella 10.10, con El Capitan in 10.11….ecc
      Se non ci fosse tale cartella, createla e nominatela voi a “modo”.
      Copiatevi all’interno FakeSmc.kext
      *Nota se venite già da altre vostre configurazioni, oltre kext sopra citato ,potete mettere gli altri necessari per il vostro hardware
      Stessa cosa se avete DSDT e/o SSDT potete copiarli in EFI/Clover/Acpi/Patched
      Immagine 
      
      Per High Sierra:
      Scaricare il driver apfs.efi a fine guida, collocarlo:
          --> EFI/clover/Driver64UEFI se stiamo usando UEFI
      --> EFI/Clover/Driver64 se stiamo usando Legacy
       
      Per chi volesse continuare ad usare HFS vi rimando a questo post:
        Come installare High Sierra in HFS direttamente dalla usb  
      Utenti Laptop:  Nel 99% è obbligatorio disattivare la grafica discreta Nvidia/Amd per installare questo nuovo osx
                                     Quindi aggiungete --> SSDT-Disable_DGPU.aml.zip
                                     in EFI/Clover/acpi/Patched della usb
      --------------------------------------------------------------------
      Per Mojave:
      Scaricare il driver apfs.efi per 10.14 a fine guida, collocarlo:
          --> EFI/clover/Driver64UEFI se stiamo usando UEFI
      --> EFI/Clover/Driver64 se stiamo usando Legacy
      Versione di clover non antecedente a V_4015
      Volete usare HFS?
      E' possibile fare un installazione diretta su altro disco o partizione, nel caso può essere usato anche per effettuare aggiornamenti...
      nel caso guardate...
       Mojave in HFS 
       Oppure direttamente da usb  
       
      Fatto questo avrete la vostra USB bootable per installare OSX.
      ………Non scordatevi Fakesmc.kext da mettere nella relativa cartella…. senza il quale non farete mai il Boot......
      *NOTA: se usato il terminale per la creazione della usb, l'installazione si dividerà in due fasi, perciò dopo il primo riavvio e necessario far partire nuovamente l'installer, selezionare lo stesso disco senza formattarlo.
      Finita questa ulteriore fase , l'installazione sarà terminata
      **NOTA** Se avete processori Broadwell,Skylake o Kabylake...usate FakeSmc.kext e relativi sensors che trovate all'interno del secondo pacchetto.. (potete usarlo anche sui precedenti senza problemi, essendo una versione più aggiornata ha ulteriore supporto per le cpu più recenti)
      Update: Fakesmc e sensors versione 6.26
      Post installazione... post #2           
       Buon Hack….. 
      Aggiornamento:Install_Mac_OS_X.command.zip (compatibile da 10.10 a 10.12)
      le info le trovate a questo post
      Ringrazio @Ciro82 che mi ha aiutato nel preparare questa guida.
      Pacchetto.zip
      Pacchetto-2.zip
      apfs.efi-10.13-NoLog.zip
      Pacchetto-Fake+Sensors 6.26.1440.zip
      apfs.efi-10.13.1-No_LOG.zip
      apfs.efi-10.13.2_No_Log.zip
      apfs.efi-10.13.3-No_Log.zip
      apfs.efi-10.13.4-No_Log.zip
      apfs.efi-10.13.5_No_Log.zip
      C_I_M.zip
       
      apfs.efi-10.14-beta1_No_Log.zip





       

    • By Lexies
      I had a working Mojave installation on my HP Z400 with clover and from a VMware image.  (Because i had a Nvidia 8800GT with no Metal support.) I found a cheap AMD RX 570 card on the local market.
      So i did a reinstall with a clean Mojave version from de App Store. Before the new card everything worked fijne exept the video card.
      (My Englisch is not great sorry!)
       
      The hardware:
      HP Z400 Motherboard in standard ATX case.  (Some powercable and other hacks needed.) Xeon W3520 (4 cores  2,67Ghz) 6x 2GB DDR3 non ECC Sapphire Radeon RX 570 4G Nitro+ SATA Harddisk BIOS version 03.61 (last)  
      BIOS Settings:
      File\Default Setup
      Restore Factory Settings as Default (You may get some new options) Apply Defaults and Exit (Reboot) Storage\Storage Options
      Legacy Diskette - Write Disable Sata Emulation - RAID+AHCI Security\Device Security
      legacy Diskette - Device hidden Embedded Security - Device Device hidden Power\Hardware Power Management
      Everyting - Enable Advanced\Processors
      Hyper-Threading – Enable  
      Install disk:
      Download the complete Mojeva Install App from de Appstor Make a install USB stick use the Terminal app and command
      “sudo /Applications/Install\ macOS\ Mojave.app/Contents/Resources/createinstallmedia --volume /Volumes/USB -- /Applications/Install\ macOS\ Mojave.app”
      Where USB is te name of the USB stick Install Clover v2.4k r4844
      Change Install Location and choose  “Install macOS Mojave”
      Customize Select:
      Install clover in the ESP Boot Sectors\Install boot0af in MBR Clover for Bios(legacy) booting\ Clover EFI 64-Bits SATA BIOS Drivers, 64 Bit\ApfsDriverLoader-64     (For Apfs in Clover) Everything else unchanged Install
      Open Clover Configurator
      And open config.plist from the EFI on the USB stick
      Select:
      Boot\Arguments   dart=0 Graphics - RadeonDeInit Kernel and Kext Patches   DellSMBIOSPatch SMBIOS Choose Mac Pro 5.1 Save
       
      Kexts:
      And place those kexts in Clover\kexts\Other (Zie Attachments)
      FakeSMC.kext (Mandatory) AHCIPortInjector_v1.0.0_Micky1979.kext (SATA) IOAHCIBlockStorageInjector_v1.0.0_Micky1979.kext (Fix SATA) NullCPUPowerManagement_v1.0.0d2_tgwbd.kext (Support CPU) VoodooHDA_v2.87.kext (Sound)
      And install disk is ready
      .
      My install was Mojave 10.14.2 and with succes updated to 10.14.3
       
      Everything is working great de only problem i have found is Mojave sees 7 memory slots and there are 6 slots in the system.
      When i define te memory slots in Clover the problem is solved see the image.
       
      kexts.zip
      config.plist.zip


    • By bbritton
      Hi
       
      I am trying to create a clean DSDT for my new hackintosh.  It is all working very well and I hope this will make things even better.
      I have a Gigabyte Z390 AORUS MASTER,
      I9-9900K
      32 gb Ram
      gigabyte vega 64 OC
       
      I extracted the DSDT and SSDT files using F4 in Clover.  I have supplied the resulting DSDT below.  THese are the four errors I get when trying to compile in MACIasl.  ALso I am using ACPI 5.1 in maciasl.
       
      12891, 6126, syntax error, unexpected PARSEOP_NAMESEG, expecting '('
      12900, 6126, syntax error, unexpected PARSEOP_CASE
      12904, 6126, syntax error, unexpected PARSEOP_NAMESEG, expecting '('
      12913, 6126, syntax error, unexpected PARSEOP_CASE, expecting $end and premature End-Of-File
       
      I am newbie to hackintosh so am learning as much as I can as i go.  I am not a programmer so the syntax errors I am not sure what to do with yet.  Any assistance would be appreciated.
       
      Thanks
       
      DSDT.dsl
      DSDT.aml
    • By MaLd0n
      Now have a Olarila app, just download app and clover folder for your Chipset! https://olarila.com/forum/viewtopic.php?f=81&t=6771   Install MacOS with Olarila Image, Step by Step, Install and Post Install
       
      https://olarila.com/forum/viewtopic.php?f=50&t=8685
          First... If you need DSDT edits for SkyLake, KabyLake or CoffeeLake... -Post your full Clover folder with original tables in Origin folder(Extract with F4 in Clover boot screen) -Post Ioreg, extract with Ioreg Explorer http://www.insanelymac.com/forum/index.php?app=core&module=attach&section=attach&attach_id=222606 -Run it, post files generated in your desktop http://www.insanelymac.com/forum/index.php?app=core&module=attach&section=attach&attach_id=222609  Installation   --Create a bootable copy of macOS Sierra Check out the link http://www.insanelymac.com/forum/files/file/559-flash-drive-maker/   --Create a bootable copy of macOS HighSierra Check out the link http://diskmakerx.com/   --Install Clover in USB stick https://sourceforge.net/projects/cloverefiboot/files/Installer/   --Replace with my Clover folder  CLOVER.zip   --Install Sierra/High Sierra and boot into system!   Post Installation   --Install Clover in HDD/SSD and replace with my folder CLOVER.zip   --Reboot and activate video!   -Nvidia WebDriver Sierra http://www.insanelymac.com/forum/topic/312525-nvidia-web-driver-updates-for-macos-sierra-update-07212017/ -Nvidia WebDriver High Sierra http://www.insanelymac.com/forum/topic/324195-nvidia-web-driver-updates-for-macos-high-sierra-update-10162017/ -Cuda http://www.insanelymac.com/forum/topic/302795-cuda-90214-is-out-update-10162017/   --DSDT My DSDT with Skylake patches DSDT.MaLd0n GA H110M-S2.zip Patches -FIX ERRORS AND WARNINGS -HPET -SATA -DMAC -SLPB -DARWIN -LPC -XHCI -PLUGIN TYPE -HDAS to HDEF -HDEF -RTC -IRQs -SBUS -BUS1 -MCHC -ALS0 -SHUTDOWN -LAN -USBX -PMCR -EC -PNLF -HDMI --FakeSMC https://bitbucket.org/RehabMan/os-x-fakesmc-kozlek --Audio https://github.com/vit9696/AppleALC --USB https://bitbucket.org/RehabMan/os-x-usb-inject-all/downloads --LAN http://www.insanelymac.com/forum/topic/287161-new-driver-for-realtek-rtl8111/   -Credits and thanks to the old and new people in the community who developed patches, kexts and bootloaders!   Slice, Kabyl, usr-sse2, jadran, Blackosx, dmazar, STLVNUB, pcj, apianti, JrCs, pene, FrodoKenny, skoczy, ycr.ru, Oscar09, xsmile, SoThOr, RehabMan, Download-Fritz, Zenit432, cecekpawon, Intel, Apple, Oracle, Chameleon Team, crazybirdy, Mieze, Mirone, Oldnapalm, netkas, Elconiglio, artut-pt, ErmaC, Pavo, Toleda, Master Chief and family, bcc9, The King, PMheart, Sherlocks, Micky1979, vit9696, vandroiy2013, Voodoo Team, Pike R. Alpha, lvs1974, Austere.J, CVad and many, many, many others!   We're all here to have fun and learn from each other!   ENJOY!  
×