Jump to content

1,793 posts in this topic

Recommended Posts

Advertisement

--------------> Piccola nota per Post Installazione 

Quando avete installato,in caso di necessità di aiuto per post installazione, aprite un topic nella sezione corretta

Ricordatevi, se non l'avete già fatto, di mettere in firma il vostro hardware in modo dettagliato, per farlo andate sul vostro profilo, voce signature.

Scaricate Hack_Info.zip

Doppio click sopra...attendete che abbia terminato.

Allegate sul vostro topic lo zip che avrà creato su vostro desktop --> HackInfo_Report

Scaricate IORegistryExplorer.zip aprite l'app su file, save as, salvate comprimete e postate l'output

Scaricate DPCIManager.zip fate la foto alla parte Status e PCI list,postale entrambe

Tutto questo fornisce informazioni utili a chi vorrà aiutarvi a risolvere i vostri problemi

-------------------------------------------------------------------------------------------------------------------------------------------------

 

 

 

Share this post


Link to post
Share on other sites

Ho eseguito l'installazione di clover uefi per l'avvio in UEFI sulla penna usb per installare osx. Clover configurator NON mi rileva la presenza della partizione EFI nella penna. Cosa ho sbagliato?

 

post-1132694-0-02382900-1437659018_thumb.jpg

 

Risolto formattando la chiave usb e facendo di nuovo l'intero procedimento! ;-)

Share this post


Link to post
Share on other sites

Non sono riuscito a far partire l'installazione dal mio notebook (in firma)... mi da System Uptime in nanoseconds... Ecco lo screen:

 

 

post-1568154-0-88381300-1437670942_thumb.jpg

Share this post


Link to post
Share on other sites

Ottima guida grazie. Una curiosita' sulla SIP. Cosa cambia utilizzando le ottime e funzionali istruzioni che hai riportato abbinandole alla cancellazione delle due linee riguardantii System/Library/Extensions nella lista posta in System/Sandbox/Compatibility.bundle/Contents/Resources/paths? Pongo questa domanda perche' cancellando detta lista mi carica i kexts che non mi fanno avere sfarfallii etc (come riportato nella mia firma) al comntrario non me li carica con nessuna di dette istruzioni, questo avviene solo con la release ufficiale non  con le beta developper o public.

 

Ti ringrazio, e felice che ti sia piaciuta

Ma....hai quotato l'intera guida... :hysterical: ... LOL ...

Per la tua domanda, sei fuori tema... :P

Per chiarimenti o suggerimenti puoi guardare il topic "nuovi Flag" nella sezione El Capitan.

oppure aprire un Topic per chiedere info a riguardo.... ;)

Share this post


Link to post
Share on other sites

          ======> AGGIORNAMENTO GUIDA.... CREATE INSTALL MEDIA

 

                                                                       Aggiunto procedimento creazione usb da terminale.

 

Ringrazio nuovamente @Ciro82....

 

Ringrazio @Jolly per aver contribuito a migliorare tale guida.

 

:thumbsup_anim:  :thumbsup_anim: :thumbsup_anim:   :thumbsup_anim:
 

Share this post


Link to post
Share on other sites

Ciao Gengik, forse ho sbagliato io , ma ho fatto varie prove proprio per evitare l'errore umano e la cosa si ripresenta. Mi sa che la procedura del createinstallmedia funziona solo col clover UEFI, con il legacy la procedura sembra andare a buon fine, il terminale lavora la mezz'oretta copiando i files poi finisce. Sembra tutto ok. Si boota con la pendrive e si installa OSX senza problemi, ma l'installazione è sospettosamente veloce, non il solito quarto d'ora ma pochi minuti. Al successivo riavvio clover non vede la partizione dov'è installato il nuovo OSX. Riavviando ancora e facendo il boot da un'altro sistema già installato, si nota che nella partizione dove dovrebbe essere stato installato OSX c'è solo una cartella con dei files (stasera ti posto la foto). Inoltre nella pendrive di installazione c'è solo il file "installa OSX", uguale a quello che c'è nella cartella applicazioni.

 

Ho provato a:

 

1) cambiare pen drive di installazione

2) cambiare Hard disk di destinazione

3) cambiare hack, ho rifatto la procedura nel portatile, che però ha sempre il vecchio bios.

 

A questo punto l'unica che mi viene in mente è che con clover legacy non funzioni.

Magari puoi specificarlo nella guida oppure vedere se qualcun altro è incorso nei miei stessi risultati (nulli).

Share this post


Link to post
Share on other sites

Ciao, Marco... Hai scaricato  l installer di El Capitan? 

Se lo hai fatto la versione che vai ad installare è  la 10.11.1.

Dalle prove da me fatte per questa versione, devi riavviare per la seconda volta l installazione. 

Il motivo è che nella prima fase viene installata la 10.11 dopo il riavvio facendo, come detto precedentemente,  ripartire per la seconda volta l installazione si va ad installarsi l aggiornamento 10.11.1.

Il motivo che dopo il primo riavvio tu non veda il disco dipende da questo. (provato personalmente) 

Sinceramente non so se dipende da Apple che non ha completamente implementato l aggiornamento nell installer. 

Quindi si pone in due fasi:

1) viene installato osx 10.11

2) viene installato aggiornamento  a 10.11.1

 

Per il discorso del contenuto della usb,... Si è vero, all interno trovi l icona dell installer come trovi in applicazioni dopo il download da app store. 

Ho messo la foto in guida appositamente per far vedere come si presenta il contenuto della usb dopo aver utilizzato quel metodo... 

È sempre  da tenere presente che è il metodo originale che Apple fornisce per creare la usb.. 

Del resto può piacere o meno,  ma dipende anche da cosa noi siamo abituati. 

È nella natura umana essere titubanti nei confronti di qualcosa di nuovo. 

Spero di aver dato quelle risposte che stavi cercando...  :)

Share this post


Link to post
Share on other sites

Più che altro avevo delle remore a scrivere per il fatto che non sapevo se era un errore mio o no,

comunque ti confermo che OSX non viene installato, anche se la schermata lo mostra. Al riavvio la partizione non viene vista in clover e esplorandola da un'altra partizione è vuota. Stasera ti posto le foto, giusto per chiarezza, non che metta in dubbio quanto hai scritto.

Share this post


Link to post
Share on other sites

Più che altro avevo delle remore a scrivere per il fatto che non sapevo se era un errore mio o no,

comunque ti confermo che OSX non viene installato, anche se la schermata lo mostra. Al riavvio la partizione non viene vista in clover e esplorandola da un'altra partizione è vuota. Stasera ti posto le foto, giusto per chiarezza, non che metta in dubbio quanto hai scritto.

Devi fare partire per la seconda volta l installazione di osx... Come detto.

Dopo il primo  riavvio non è terminata l installazione,  quindi nel disco ancora non c'è tutto. 

Clover non vede il disco per fare il boot per questo motivo. 

Rileggi quanto detto.. 

Share this post


Link to post
Share on other sites
Guest
You are commenting as a guest. If you have an account, please sign in.
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By yehia2amer
      Dell Precision T7610 Workstation
      Hackintosh GUIDE (Work in Progress)
       
                        
      Introduction: 
      Hi Everyone,
      This Workstation used to be a Beast with Dual CPUs and tons of RAM, I Know it is now normal to get that much cores in a Desktop but it is still a very decent machine for me (As a Programmer), and I thought it would be a good idea to Install MacOS as the Daily Driver Rather than Linux and It turns out to be a very Great Experience (with Some Challenges ).
       
      Specs:
      CPU: 2x Xeon E5-2680 v2 2.8GHz Ten Core Processors RAM: 128 GB 1333 MHz DDR3 ECC Memory GPU: SAPPHIRE PULSE Radeon RX 580 8GD5 Chipset: Intel C602 Audio: Realtek ALC3220 (ALC280) High Definition Audio SAS Drive Controllers (RAID): LSI 2308 SATA/SAS 6Gb/s controller with host based RAID 0, 1, 10 (4  Network Controller 1: Intel 82579 Gigabit Ethernet controller with Remote Wake UP, PXE and Jumbo frames support
      Network Controller 2: Intel Ethernet Controller I210
      NEC USB3.0 xHCI Controller: Renesas Electronics uPD720201 & uPD720202
       
      Working:
      Both "Xeon E5-2680 v2" and all cores with Power Management and P-States (using VoodooTSCSync & ssdtPRGen.sh) ATI Radeon HD 4870 (Vanilla) Realtek ALC3220 (ALC280)  (using VoodooHDA till Now - it is partially working with AppleALC using layout-id 13) LSI 2308 SAS (using AstekFusion2) Intel 82579 Network Controller (Vanilla) Intel I210 Network Controller (IntelMausiEthernet) USB 2.0  
      Not Working:
      NEC USB3.0 xHCI Controller (Renesas Electronics uPD720201 & uPD720202) Sleep  
      https://github.com/yehia2amer/Dell-Precision-T7610-Workstation-Hackintosh-Guide
    • By RougeOne
      Budget Workstation MacOS 10.14.1 build: z370 AORUS Gaming 5 - i5-8600K - RX 580 - UHD 630
      flawless iGPU/dGPU integration, fast FCPX editing/rendering, great overall performance for ~$1200 / ~£1000
       
      Update: updated WhateverGreen and Lilu, then updated OS to 10.14.3 and everything is fine! Even iMessage, which previously I hadn't been able to make work, is now working - possibly the update flushed the NVRAM?
       
      I'm gonna come straight out and admit it - I used newb tools which are considered taboo on InsanelyMac, and so this isn't so much an installation guide as it is a green flag to anyone considering the same hardware. My first and previous Hackintosh project was just over ten years ago and this site was massively helpful, so this is my (very small) way of giving back.
       
      EFI DIRECTORY
      http://s000.tinyupload.com/index.php?file_id=97606131925137056003
       
      HARDWARE
      CPU: Intel i5-8600K 3.6GHz hexacore (contains UHD 630 iGPU)
      CPU Cooler: be quiet! Pure Rock Slim (no paste needed, and fan facing front)
      Mobo: GIGABYTE z370 AORUS Gaming 5 (WIFI)
      RAM: 1x 8GB CORSAIR Vengeance LPX C16 2666MHz (in first slot)
      GFX Card: Sapphire RX 580 NITRO+ SE
      SATA: used ports 0, 1, 3, 5 (HDD problems when connected to port 4)
      HDD: generic
      DVD Drive: generic
      PSU: EVGA 500W Semi Modular (but you should get 650W!)
      Case: CoolerMaster CM590 III
      Fans: 2x stock case fans (one sucky on front, one blowy on back), 3x be quiet! BL046 120mm fans (two blowy on top, one sucky on front). Airflow near-perfectly balanced.
       
      ADVICE
      With the Clover configuration, you want to pay close attention to all things relating to graphics. There are some specific settings for ACPI, Boot, Devices and Graphics which should be copied exactly in order to get the iGPU and dGPU to work in perfect harmony. For instance, make sure you use ig-platform-id 59120003 rather than 59120000 if you want FCPX to be usable. With the right settings, FCPX will not only run, but run flawlessly.
       
      I was not able to figure out how to make NVRAM/PRAM behave itself, and I got errors when I tried to issue relevant commands. As a result, I could not at first get iMessage to work properly. It worked once on my first installation attempt but not from subsequent attempts. This Clover configuration therefore has no consideration whatsoever toward iMessage reliability - however, iMessage ended up working somehow, anyway - I noticed it after I'd updated to 10.14.3 but this may just have been coincidence.
       
      Onboard WiFi does not work. There is no driver for it. I'm using wired ethernet to a bridge router as it was cheaper than getting a compatible PCI card.
       
      Audio is working well after I installed the z370 audio patch, then the ALC1220 codecs, then AppleALC.
       
      With kexts for generic 3rd party SATA and generic 3rd party eSATA, my HDDs and DVD drive work perfectly well.
       
      Sleep/Wake functions run perfectly. iCloud functions run perfectly. Shutdown leaves the mobo LEDs on, annoyingly.
       
      My USB 3 ports seem to suffer from low power output, and I don't know why.
       
      Overall, this system appears to run about as well under MacOS 10.14 Mojave as it does under Windows 7. I would solidly recommend this build to anyone looking to build a computer for workstation purposes, on a budget.
    • By plasticworld
      After a long run, I successfully upgraded High Sierra to mojave 10.14 on an intel 5 series chipset MotherBoard.
       
      MotherBoard: H55ms2
      RAM: 6GB
      GPU1: Saphire AMD RX 460
      GPU2: Nvidia 8400GS
      Storage: 500 GB HDD WD Green.
       
      The requirement:
      1) macOS pre mojave.
      2) macOS mojave installer from Apple store.
      3) Empty partition or USB to upgrade from.
      4) Un-mout all unused dmgs.
      5) GPT/GUID HDD.
       
      HOWOT:
      1) Prepare an empty partition or USB with at least 6 GB.
      2) Format the partition or USB with GUID partition table and HFS+ partition with a name BootablePartition.
      3) Go to /Application/Install macOS Mojave.app.
      4) Show Package Contents.
      5) Go to Contents/SharedSupport you will find BaseSystem.dmg.
      6) Double click on BaseSystem.dmg to mount.
      7) From Disk Utilty click on your partition or the USB that you prepared from number (2).
      8) Click on restore, and chose OS X Base System (BaseSystem.dmg image), then restore it to that partition or USB.
      9) After restoring rename the partition back to BootablePartition.
      9) Run this command:
      rm -rfv /Volumes/BootablePartition/System/Installation/Packages 10) Create a new folder instead of the broken link and name it Packages, run this command:
      mkdir -v /Volumes/BootablePartition/System/Installation/Packages 11) Go back to /Application/Install macOS Mojave.app and repeat number 2.
      12) Go to Contents/SharedSupport you will find InstallESD.dmg.
      13) Mount InstallESD.dmg.
      14) Run this command:
      cp -v /Volumes/InstallESD/Packages/OSInstall.mpkg /Volumes/BootablePartition/System/Installation/Packages/ 15) Download the latest clover from https://sourceforge.net/projects/cloverefiboot/
      16) Install clover on your USB BootablePartition or in a different USB to boot from it. delete all your CLOVER/kext/10.xx and keep others, make sure you don't have any extra kext rather than FakeSMC.kext in the other folder.
      in my case I used FakeSMC.kext and my lan kext RealtekRTL8111.kext.
      17) known Problems in my build: 
      If I updated directly from the apple store the installer in clover will boot with a cross circle sign.
      The FIX is to add this to Clover KextToPatch Thanks to @sunKi http://www.insanelymac.com/forum/topic/327488-macos-high-sierra-final-release-is-out-17a365/page-10?do=findComment&comment=2505086 this fix is still working for me in mojave.
      <key>KextsToPatch</key> <array> <dict> <key>Comment</key> <string>fix IO error ICH10 for 10.13, credit SunKi</string> <key>Disabled</key> <false/> <key>Find</key> <data> RYX2D5XCiciD4P5mhcl4D4TSdQs= </data> <key>Name</key> <string>AppleAHCIPort</string> <key>Replace</key> <data> iciD4P5mhckPmMFBCMyQkJCQdQs= </data> </dict> <dict> <key>Comment</key> <string>fix hotplug ICH10 for 10.13, credit SunKi</string> <key>Disabled</key> <false/> <key>Find</key> <data> icglQGACAD1AIAAAdQyB4b9///+Ji1EBAAA= </data> <key>Name</key> <string>AppleAHCIPort</string> <key>Replace</key> <data> kJCQkJCQkJCQkJCQkJCQkJCQkJCQkJCQkJA= </data> </dict> <dict> <key>Comment</key> <string>External icons patch</string> <key>Disabled</key> <false/> <key>Find</key> <data> RXh0ZXJuYWw= </data> <key>Name</key> <string>AppleAHCIPort</string> <key>Replace</key> <data> SW50ZXJuYWw= </data> </dict> </array> 18) make sure you have apfs.efi copy it from /Volumes/BootablePartition/usr/standalone/i386/apfs.efi to your EFI/CLOVER/drivers64/ and EFI/CLOVER/drivers64UEFI/.
      19) SMBIOS mac model that I use is iMac13,2.
      20) Go to /Application/Install macOS Mojave.app click on it and chose to install to your macOS Mojave partition.
      21) Reboot.
      22) From clover chose BootablePartion.
      23) If everything is okie BootablePartition will boot to install macOS mojave, wait wait wait till it finish it might take to 1 hour just wait it will reach the auto reboot soon .
      24) Boot to your old macOS Hight Sierra that will be your mojave partition now and enjoy.
       
      POST Install:
      1) audio: 
      a) Download Lilu.kext and AppleALC.kext or build them from source (which I did).
      b) place them in your /EFI/CLOVER/kext/others/
      c) add your audio layout in clover/Devices dict options in my case it's ALC888B which has the layout of 1:
      <key>Audio</key> <dict> <key>Inject</key> <string>1</string> </dict> d) I had to add beta args to clover/Boot dict, argument (-lilubeta -alcbeta):
       
      <key>Arguments</key> <string>-lilubeta -alcbeta</string> 2) Add number 14 KextsToPath array to your clover as well.

      Anything else is working for me I didn't need any extra clover kext so far, I tried whatevergreen.kext to fire up my rx 460 without the helper card but no success, So I am just sticking with booting from Nvidia as a first GPU from my motherboard configuration then swap the cables after choosing my macOS partion from clover.
       
      After upgrading my HFS+ High Sierra partition converted to APFS, no know problem so far.

      Happy build and more info about the partitioning method with a more detailed instructions in this post that I used to update my Sierra to High Sierra
       
      Special thanks to crazybirdy, sunKi and all of you out there that make this happens.
    • By JhonneR
      Good morning, everyone, I'm sorry if I was wrong in choosing the topic but I need help.
      I have found it extremely difficult to mount a Hackintosh in my acer.
      Setup;
      I5 2430m 2.4 6GB RAM
      Mobo P5we0 - Intel intel Graphics 3000
      At the moment I have not found out what my audio codecs are.
      but I'll leave the link on the motherboard.
      however, my real problem is several.
      I have already used the itakos image, I have already used several images that could be installed normally and that after installing the image I do not have internet via cable or wireless.
      And another, I already looked in other forums and I know that I will be called a donkey in the logical question but I have not been able to install the [url=&quot;http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/&quot;]#####[/url] or clover to start from the Hard Disk, so I do not know what to do.At the moment I still do not know if there has already been someone who has already installed the High Sierra or just the Sierra in this notebook model and obtained permanent success.
      If anyone can help me, I'll be grateful.
      Installations without success, but with the system already installed in ACER;
      SIERRA
      HIGH SIERRA
      MOJAVE
      All with the same symptom. Starting only by the bootable USB stick and without internet connection via cable and wireless.
      Appreciate ! Acer 5750 Official Page
    • By Slice
      Since rev 4844 Vector Themes are supported and there are ready-to-use Clovy by Clovy, cesium by Slice and BGM_SVG by Blackosx.
      You may see it's structure to create own theme
      -------------------------------------------------------------------------------------------------------------------------------------------------------
       
       
      Now I want to add vector graphics support in Clover. See rev 4560 and later.
      It is not working yet but designers may begin to create Vector Themes.
      It supposed to consist of SVG elements and has design size. It will be rendered to any screen size scaled from design size.
       
      What application in macOS can create SVG graphics?
      Inkscape is not working in macOS 10.11+. Pity.
      LibreOffice Draw works with SVG but buggy.
      Boxy SVG cost 10$ but looks good enough. It creates the best in simplicity files and have more then enough features.
      Illustrator is good but expensive.
       
      How to improve SVG file?
      Clover has restricted support for SVG. It is your job to make compatible file and as small as possible to speedup rendering.
      Some helps:
      Help:Inkscape – From invalid to valid SVG Inkscape files
      From invalid to valid SVG Adobe Illustrator files
      From invalid to valid SVG files of other editors: BKchem, ChemDraw and CorelDRAW
      Help:Illustrator – Assistance with creating and saving SVG images in Adobe Illustrator that will pass W3C validation
      User:Quibik/Cleaning up SVG files manually
      Later I will write own instructions specific to Clover abilities.
       
      How to create SVG fonts?
      You can google to find ready-to-use SVG fonts.  I found some problems with too beaty fonts: slow rendering and overflow crash. Be careful.
      You can get ttf or otf fonts and convert them into svg by using online WEB services. Not a problem to google.
      But then I want to find a way to simplify the font to reduce a size and speedup rendering.
      You can create own font by FontForge It is opensource and available for Windows, Mac and GNU+Linux. It creates otf font which you can convert to svg font.
       
      Pictures from Badruzeus
      https://www.insanelymac.com/forum/applications/core/interface/file/attachment.php?id=301597
×