Jump to content
ErmaC

Clover Problems and Solutions

3,188 posts in this topic

Recommended Posts

Is it working? I got only blinking underscore while the same compiled by gcc working.

I can confirm that it works well on my hardware. I compile it on El Cap with Xcode 7Beta + command line tools, and comment out these inf's in clover.fdf as I don't need IDE or SCSI controllers:

 

  #INF  Clover/VBoxIdeControllerDxe/VBoxIdeControllerDxe.inf

  #INF  Clover/VBoxIdeBusDxe/VBoxIdeBusDxe.inf
    INF  Clover/SataControllerDxe/SataControllerDxe.inf
  #INF  MdeModulePkg/Bus/Ata/AtaAtapiPassThru/AtaAtapiPassThru.inf
  #INF  Clover/AtaAtapi/AtaAtapiPassThru.inf
  #INF  MdeModulePkg/Bus/Ata/AtaBusDxe/AtaBusDxe.inf
  #INF  Clover/AtaBus/AtaBusDxe.inf
  #INF  MdeModulePkg/Bus/Scsi/ScsiBusDxe/ScsiBusDxe.inf
  #INF  Clover/DVDBus/ScsiBusDxe.inf
  #INF  MdeModulePkg/Bus/Scsi/ScsiDiskDxe/ScsiDiskDxe.inf
  #INF  Clover/DVDDisk/ScsiDiskDxe.inf
  #INF  IntelFrameworkModulePkg/Bus/Pci/IdeBusDxe/IdeBusDxe.inf
 
Then:
 
./ebuild.sh -clang -release --only-sata0 --x64

Share this post


Link to post
Share on other sites
Advertisement

 

I can confirm that it works well on my hardware. I compile it on El Cap with Xcode 7Beta + command line tools, and comment out these inf's in clover.fdf as I don't need IDE or SCSI controllers:

 

  #INF  Clover/VBoxIdeControllerDxe/VBoxIdeControllerDxe.inf

  #INF  Clover/VBoxIdeBusDxe/VBoxIdeBusDxe.inf
    INF  Clover/SataControllerDxe/SataControllerDxe.inf
  #INF  MdeModulePkg/Bus/Ata/AtaAtapiPassThru/AtaAtapiPassThru.inf
  #INF  Clover/AtaAtapi/AtaAtapiPassThru.inf
  #INF  MdeModulePkg/Bus/Ata/AtaBusDxe/AtaBusDxe.inf
  #INF  Clover/AtaBus/AtaBusDxe.inf
  #INF  MdeModulePkg/Bus/Scsi/ScsiBusDxe/ScsiBusDxe.inf
  #INF  Clover/DVDBus/ScsiBusDxe.inf
  #INF  MdeModulePkg/Bus/Scsi/ScsiDiskDxe/ScsiDiskDxe.inf
  #INF  Clover/DVDDisk/ScsiDiskDxe.inf
  #INF  IntelFrameworkModulePkg/Bus/Pci/IdeBusDxe/IdeBusDxe.inf
 
Then:
 
./ebuild.sh -clang -release --only-sata0 --x64

 

But AtaAtapi is a Sata driver provided AHCI mode. You may exclude it only if you set BiosBlockIO.

Share this post


Link to post
Share on other sites

Thanks, this is valuable info!

Accepted into 3248.

I can also note this MacBook uses 

"Intel HD Graphics 5300"

"AAPL,ig-platform-id" = 0x161e0001

May be someone found this info usefull.

The Broadwell info updated by 3248 is reverted in 3249, please push the change of TheRacerMaster again.

Share this post


Link to post
Share on other sites

The Broadwell info updated by 3248 is reverted in 3249, please push the change of TheRacerMaster again.

Oops! Thanks for the note. Restored.

Share this post


Link to post
Share on other sites

Apologies if this is in the wrong section or not a bug!

 

In my "Custom > Entries" section I have separate entries for Yosemite and El Capitan including patches that are unique to each OS but if i check the boot.log file it appears to be running both regardless of which OS I boot into.

 

boot.log (Relevant section only)

0:115  0:000  Copying global patch settings
0:115  0:000  KextsToPatch: 2 requested
0:115  0:000  KextToPatch 0: IOGraphicsFamily (Yosemite Boot Logo: Patch 1) Kext bin patch, data len: 5
0:115  0:000  KextToPatch 1: IOGraphicsFamily (Yosemite Boot Logo: Patch 2) Kext bin patch, data len: 5
0:115  0:000  Filled in patch settings
0:115  0:000  Copying global patch settings
0:115  0:000  Copying global patch settings
0:115  0:000  KextsToPatch: 2 requested
0:115  0:000  KextToPatch 0: IOGraphicsFamily (El Capitan Boot Logo: Patch 1) Kext bin patch, data len: 5
0:115  0:000  KextToPatch 1: IOGraphicsFamily (El Capitan Boot Logo: Patch 2) Kext bin patch, data len: 5
0:115  0:000  Filled in patch settings
0:115  0:000  Copying global patch settings
0:115  0:000  Copying global patch settings
0:115  0:000  Copying global patch settings
0:115  0:000  CustomEDID ok

Custom > Entries > Yosemite Partition

				<dict>
					<key>Volume</key>
					<string>F57C54E7-2E96-4FA9-B73F-A75D3F237432</string>
					<key>Type</key>
					<string>OSX</string>
					<key>Arguments</key>
					<string>kext-dev-mode=1</string>
					<key>FullTitle</key>
					<string>OS X 10.10.5 (14F27) Yosemite</string>
					<key>InjectKexts</key>
					<true/>
					<key>NoCaches</key>
					<false/>
					<key>Hidden</key>
					<false/>
					<key>KernelAndKextPatches</key>
					<dict>
						<key>KextsToPatch</key>
						<array>
							<dict>
								<key>Comment</key>
								<string>Yosemite Boot Logo: Patch 1</string>
								<key>Find</key>
								<data>hcB0a0g=</data>
								<key>Name</key>
								<string>IOGraphicsFamily</string>
								<key>Replace</key>
								<data>McB0W0g=</data>
							</dict>
							<dict>
								<key>Comment</key>
								<string>Yosemite Boot Logo: Patch 2</string>
								<key>Find</key>
								<data>QYjE6xE=</data>
								<key>Name</key>
								<string>IOGraphicsFamily</string>
								<key>Replace</key>
								<data>QYjE6zE=</data>
							</dict>
						</array>
					</dict>
				</dict>

Custom > Entries > El Capitan Partition

				<dict>
					<key>Volume</key>
					<string>B262BC9F-1104-4184-8314-C6943AB0506E</string>
					<key>Type</key>
					<string>OSX</string>
					<key>FullTitle</key>
					<string>OS X 10.11 (15A243d) El Capitan</string>
					<key>InjectKexts</key>
					<true/>
					<key>NoCaches</key>
					<false/>
					<key>Hidden</key>
					<false/>
					<key>KernelAndKextPatches</key>
					<dict>
						<key>KextsToPatch</key>
						<array>
							<dict>
								<key>Comment</key>
								<string>El Capitan Boot Logo: Patch 1</string>
								<key>Find</key>
								<data>hcB0a0g=</data>
								<key>Name</key>
								<string>IOGraphicsFamily</string>
								<key>Replace</key>
								<data>McB0W0g=</data>
							</dict>
							<dict>
								<key>Comment</key>
								<string>El Capitan Boot Logo: Patch 2</string>
								<key>Find</key>
								<data>AQAAdRc=</data>
								<key>Name</key>
								<string>IOGraphicsFamily</string>
								<key>Replace</key>
								<data>AQAAdBc=</data>
							</dict>
						</array>
					</dict>
				</dict>

Share this post


Link to post
Share on other sites

Hi Slice, can I just check that answer wasn't directly in response to my query please?

Yes, I just have no relation to custom entries. Apianti and sothor did this.

Share this post


Link to post
Share on other sites

Clover build broken building against latest edk2:

 

Speedy-OSX:Clover RehabMan$ ./ebuild.sh 
TOOLCHAIN_DIR: /Users/Admin/Projects/clover.git/edk2/Clover/../../toolchain
Initializing workspace
Loading previous configuration from $WORKSPACE/Conf/BuildEnv.sh
WORKSPACE: /Users/Admin/Projects/clover.git/edk2
EDK_TOOLS_PATH: /Users/Admin/Projects/clover.git/edk2/BaseTools

Running edk2 build for CloverX64 using the command:
build  -D USE_LOW_EBDA -p Clover/Clover.dsc  -a X64 -b RELEASE -t GCC49 -n 9 

Build environment: Darwin-14.5.0-x86_64-i386-64bit
Build start time: 08:25:28, Aug.25 2015

WORKSPACE        = /Users/Admin/Projects/clover.git/edk2
ECP_SOURCE       = /Users/Admin/Projects/clover.git/edk2/EdkCompatibilityPkg
EDK_SOURCE       = /Users/Admin/Projects/clover.git/edk2/EdkCompatibilityPkg
EFI_SOURCE       = /Users/Admin/Projects/clover.git/edk2/EdkCompatibilityPkg
EDK_TOOLS_PATH   = /Users/Admin/Projects/clover.git/edk2/BaseTools


Architecture(s)  = X64
Build target     = RELEASE
Toolchain        = GCC49

Active Platform          = /Users/Admin/Projects/clover.git/edk2/Clover/Clover.dsc
Flash Image Definition   = /Users/Admin/Projects/clover.git/edk2/Clover/Clover.fdf

Processing meta-data .

build.py...
/Users/Admin/Projects/clover.git/edk2/Clover/Clover.dsc(...): error 4000: Instance of library class [VarCheckLib] is not found
	in [/Users/Admin/Projects/clover.git/edk2/MdeModulePkg/Universal/Variable/RuntimeDxe/VariableRuntimeDxe.inf] [X64]
	consumed by module [/Users/Admin/Projects/clover.git/edk2/MdeModulePkg/Universal/Variable/RuntimeDxe/VariableRuntimeDxe.inf]
 

- Failed -
Build end time: 08:25:30, Aug.25 2015
Build total time: 00:00:01

Share this post


Link to post
Share on other sites

You can revert to that version by typing following:

svn up -r 18198 ~/path/to/Clover/edk2

If you didn't do any changes to edk2, you should also revert the conflicts with "theirs-conflict" by typing "tc" on every conflict.

Share this post


Link to post
Share on other sites

Attention!

EDK2 must be revision 18198!

 

New EDK2 improvement will not improve Clover.

Thanks for the information. I didn't find it documented anywhere that Clover requires a specific edk2 rev.

 

Is the Clover setup/build process documented somewhere?

You can revert to that version by typing following:

svn up -r 18198 ~/path/to/Clover/edk2

If you didn't do any changes to edk2, you should also revert the conflicts with "theirs-conflict" by typing "tc" on every conflict.

 

Thanks. It was helpful as I'm not used to svn (prefer git). It saved me having to look up the syntax required to checkout (git term) a particular version.

Share this post


Link to post
Share on other sites

svn co -r 18198 https://svn.code.sf.net/p/edk2/code/trunk/edk2 edk2

 

 

Thanks for the information. I didn't find it documented anywhere that Clover requires a specific edk2 rev.

Is the Clover setup/build process documented somewhere?

 

 

http://clover-wiki.zetam.org/Development#Compiling-from-source

But I afraid the instructions are obsolete.

Or here Post#14 Development

Share this post


Link to post
Share on other sites

Hi Slice

Is it possible to update KernelHaswellE to support 10.10.3+. FakeCPUID does not support it too.

Thanks

 

:gun:

Tell me what to do and I will commit this to repo.

Share this post


Link to post
Share on other sites

Hi there !

 

I'd like to report issues with ShutDown and El Capitan :

 

- when select Restart, the system shuts down, the power led stays ON and the system restart

- when I select ShutDown, the system shuts down, the power led switches OFF but 3 secondes later the power led switches ON and the system restart all by itself !

 

I noticed that

- there is no pb on Yosemite (10.10.5 for the time being)

- when I unplug all my USB devices (except BT which is on a mini-PCIe port), the system shuts down normally.

 

Config :

- 10.11. GM

- Clover v3262

- USB injected by SSDT (no change since 10.10)

 

Method (_SB.PCI0.EHC1._DSM, 4, NotSerialized)
{
If (LEqual (Arg2, Zero))
{
Return (Buffer (One)
{
0x03
})
}

Return (Package (0x15)
{
"AAPL,slot-name",
"Built In",
"name",
"Intel EHCI Controller",
"model",
Buffer (0x3E)
{
"Intel 8 Series Chipset Family USB Enhanced Host Controller #1"
},

"device_type",
Buffer (0x0F)
{
"USB Controller"
},

"AAPL,current-available",
0x0834,
"AAPL,current-extra",
0x0A8C,
"AAPL,current-in-sleep",
0x03E8,
"AAPL,current-extra-in-sleep",
0x0834,
"AAPL,max-port-current-in-sleep",
0x0A8C,
"AAPL,device-internal",
0x02,
Buffer (One)
{
0x00
}
})
}

Method (_SB.PCI0.EHC2._DSM, 4, NotSerialized)
{
If (LEqual (Arg2, Zero))
{
Return (Buffer (One)
{
0x03
})
}

Return (Package (0x15)
{
"AAPL,slot-name",
"Built In",
"name",
"Intel EHCI Controller",
"model",
Buffer (0x3E)
{
"Intel 8 Series Chipset Family USB Enhanced Host Controller #2"
},

"device_type",
Buffer (0x0F)
{
"USB Controller"
},

"AAPL,current-available",
0x0834,
"AAPL,current-extra",
0x0A8C,
"AAPL,current-in-sleep",
0x03E8,
"AAPL,current-extra-in-sleep",
0x0834,
"AAPL,max-port-current-in-sleep",
0x0A8C,
"AAPL,device-internal",
0x02,
Buffer (One)
{
0x00
}
})
}

Method (_SB.PCI0.XHC._DSM, 4, NotSerialized)
{
If (LEqual (Arg2, Zero))
{
Return (Buffer (One)
{
0x03
})
}

Return (Package (0x15)
{
"AAPL,slot-name",
"Built In",
"name",
"Intel XHCI Controller",
"model",
Buffer (0x37)
{
"Intel 8 Series Chipset Family USB xHCI Host Controller"
},

"device_type",
Buffer (0x0F)
{
"USB Controller"
},

"AAPL,current-available",
0x0834,
"AAPL,current-extra",
0x0A8C,
"AAPL,current-in-sleep",
0x03E8,
"AAPL,current-extra-in-sleep",
0x0834,
"AAPL,max-port-current-in-sleep",
0x0A8C,
"AAPL,device-internal",
0x02,
Buffer (One)
{
0x00
}
})
}

 

Share this post


Link to post
Share on other sites

Hi there !

 

I'd like to report issues with ShutDown and El Capitan :

 

- when select Restart, the system shuts down, the power led stays ON and the system restart

- when I select ShutDown, the system shuts down, the power led switches OFF but 3 secondes later the power led switches ON and the system restart all by itself !

 

I noticed that

- there is no pb on Yosemite (10.10.5 for the time being)

- when I unplug all my USB devices (except BT which is on a mini-PCIe port), the system shuts down normally.

 

Config :

- 10.11. GM

- Clover v3262

- USB injected by SSDT (no change since 10.10)

 

Method (_SB.PCI0.EHC1._DSM, 4, NotSerialized)

{

If (LEqual (Arg2, Zero))

{

Return (Buffer (One)

{

0x03

})

}

 

Return (Package (0x15)

{

"AAPL,slot-name",

"Built In",

"name",

"Intel EHCI Controller",

"model",

Buffer (0x3E)

{

"Intel 8 Series Chipset Family USB Enhanced Host Controller #1"

},

 

"device_type",

Buffer (0x0F)

{

"USB Controller"

},

 

"AAPL,current-available",

0x0834,

"AAPL,current-extra",

0x0A8C,

"AAPL,current-in-sleep",

0x03E8,

"AAPL,current-extra-in-sleep",

0x0834,

"AAPL,max-port-current-in-sleep",

0x0A8C,

"AAPL,device-internal",

0x02,

Buffer (One)

{

0x00

}

})

}

 

Method (_SB.PCI0.EHC2._DSM, 4, NotSerialized)

{

If (LEqual (Arg2, Zero))

{

Return (Buffer (One)

{

0x03

})

}

 

Return (Package (0x15)

{

"AAPL,slot-name",

"Built In",

"name",

"Intel EHCI Controller",

"model",

Buffer (0x3E)

{

"Intel 8 Series Chipset Family USB Enhanced Host Controller #2"

},

 

"device_type",

Buffer (0x0F)

{

"USB Controller"

},

 

"AAPL,current-available",

0x0834,

"AAPL,current-extra",

0x0A8C,

"AAPL,current-in-sleep",

0x03E8,

"AAPL,current-extra-in-sleep",

0x0834,

"AAPL,max-port-current-in-sleep",

0x0A8C,

"AAPL,device-internal",

0x02,

Buffer (One)

{

0x00

}

})

}

 

Method (_SB.PCI0.XHC._DSM, 4, NotSerialized)

{

If (LEqual (Arg2, Zero))

{

Return (Buffer (One)

{

0x03

})

}

 

Return (Package (0x15)

{

"AAPL,slot-name",

"Built In",

"name",

"Intel XHCI Controller",

"model",

Buffer (0x37)

{

"Intel 8 Series Chipset Family USB xHCI Host Controller"

},

 

"device_type",

Buffer (0x0F)

{

"USB Controller"

},

 

"AAPL,current-available",

0x0834,

"AAPL,current-extra",

0x0A8C,

"AAPL,current-in-sleep",

0x03E8,

"AAPL,current-extra-in-sleep",

0x0834,

"AAPL,max-port-current-in-sleep",

0x0A8C,

"AAPL,device-internal",

0x02,

Buffer (One)

{

0x00

}

})

}

 

 

Try with FakePCIID.kext+FakePCIID_XHCIMux.kext.

Did you create a proper injector for your USB ports? (and rename EHCx->EH0x)?

Share this post


Link to post
Share on other sites

Try with FakePCIID.kext+FakePCIID_XHCIMux.kext.

Did you create a proper injector for your USB ports? (and rename EHCx->EH0x)?

I edited my SSDT :

EHC1 > EH01

EHC2 > EH02

XHC > XHC1

And add your kext to /EFI kext folder 

 

And it seems to work !!! Thanks a lot !  :D

 

So it was not really Clover related ...

Share this post


Link to post
Share on other sites

Not sure if this is the correct thread to post this, but here's a simple change that allows Clover to respect the "bless --nextonly" option.  A next-only boot adds efi-boot-next and efi-boot-next-data to NVRAM, both of which are cleaned up by boot.efi automatically.

Index: rEFIt_UEFI/Platform/Nvram.c
===================================================================
--- rEFIt_UEFI/Platform/Nvram.c (revision 3270)
+++ rEFIt_UEFI/Platform/Nvram.c (working copy)
@@ -465,8 +465,14 @@
     DBG ("already parsed\n");
     return EFI_SUCCESS;
   }
-  
-  gEfiBootDeviceData = GetNvramVariable (L"efi-boot-device-data", &gEfiAppleBootGuid, NULL, &Size);
+
+  gEfiBootDeviceData = GetNvramVariable (L"efi-boot-next-data", &gEfiAppleBootGuid, NULL, &Size);
+  if (gEfiBootDeviceData != NULL) {
+    DBG ("\n");
+    DBG (" efi-boot-next-data: %s\n", FileDevicePathToStr (gEfiBootDeviceData));
+  } else {
+    gEfiBootDeviceData = GetNvramVariable (L"efi-boot-device-data", &gEfiAppleBootGuid, NULL, &Size);
+  }
   if (gEfiBootDeviceData == NULL) {
     DBG (" efi-boot-device-data not found\n");
     return EFI_NOT_FOUND;

Share this post


Link to post
Share on other sites

Not sure, if it's just me or?

 

KextsToPatch never apllied while in other plist (except default: config.plist). Lets say i've 2 plist: "config" as default & "test" for trial & error purposes.

  • Boot to Clover GUI.
  • Goto option: change plist (ex: config -> test) + enter, all settings change to new one (test.plist).
  • Esc back to main menu.
  • Boot to OS partition & patch not applied, never.
  • Copying KextsToPatch values from test to config, boot with config, patch applied.

** with enabled allow kext patch in menu

** maybe: bott-args too

Share this post


Link to post
Share on other sites

 

Not sure if this is the correct thread to post this, but here's a simple change that allows Clover to respect the "bless --nextonly" option.  A next-only boot adds efi-boot-next and efi-boot-next-data to NVRAM, both of which are cleaned up by boot.efi automatically.

Index: rEFIt_UEFI/Platform/Nvram.c
===================================================================
--- rEFIt_UEFI/Platform/Nvram.c (revision 3270)
+++ rEFIt_UEFI/Platform/Nvram.c (working copy)
@@ -465,8 +465,14 @@
     DBG ("already parsed\n");
     return EFI_SUCCESS;
   }
-  
-  gEfiBootDeviceData = GetNvramVariable (L"efi-boot-device-data", &gEfiAppleBootGuid, NULL, &Size);
+
+  gEfiBootDeviceData = GetNvramVariable (L"efi-boot-next-data", &gEfiAppleBootGuid, NULL, &Size);
+  if (gEfiBootDeviceData != NULL) {
+    DBG ("\n");
+    DBG (" efi-boot-next-data: %s\n", FileDevicePathToStr (gEfiBootDeviceData));
+  } else {
+    gEfiBootDeviceData = GetNvramVariable (L"efi-boot-device-data", &gEfiAppleBootGuid, NULL, &Size);
+  }
   if (gEfiBootDeviceData == NULL) {
     DBG (" efi-boot-device-data not found\n");
     return EFI_NOT_FOUND;

Accepted to 3271, although I don't know what is ;) .

 

Not sure, if it's just me or?

 

KextsToPatch never apllied while in other plist (except default: config.plist). Lets say i've 2 plist: "config" as default & "test" for trial & error purposes.

  • Boot to Clover GUI.
  • Goto option: change plist (ex: config -> test) + enter, all settings change to new one (test.plist).
  • Esc back to main menu.
  • Boot to OS partition & patch not applied, never.
  • Copying KextsToPatch values from test to config, boot with config, patch applied.

** with enabled allow kext patch in menu

** maybe: bott-args too

I think it is corrected in 3270. Check, please, again.

Share this post


Link to post
Share on other sites

  • Recently Browsing   0 members

    No registered users viewing this page.

Announcements

  • Similar Content

    • By STLVNUB
      *Put the script into its own folder as it will create other folders*
      What is BTB?
      Script file to clone and help build Clover or Opencore repos
      Script will create link to itself in /usr/local/bin/bob
      Script SHOULD fix up any stray bobs you may have.
      Then you only need to type bob. and a parameter
      "a" for ACID repo, official
      "d" for ACID repo DUET build
      "c" for CLOVER
      "e" to erase UDK Folder
      Easier typing bob than.....usual stuff
      YOU WILL NEED TO cmod+x THE SCRIPT
      Enjoy
       
    • By cvad
      View File Bootdisk Utility
      Make bootable USB Flash Disk for MAC OS X with Latest Clover bootloader revision fast and easy by one click! under OS Windows.
      Special utility from cvad & russian MAC community for new hackintosh users.
       
      Enjoy...
       
      For more information and complete instructions please see this topic.
       
      Anyone who likes the program, please support its Community Score.
       
       
      Feel free to "Rate File"
      Submitter cvad Submitted 04/28/2013 Category Bootloaders  
    • By ALGhackintosh
      Hi @chris1111 i have a tenda w311ma usb wireless adapter , i wanted to make it work with my catalina hackintosh so i installed the driver from the official site , the Rt2870driver.kext file and your wireless panel utility but i have a problem : The software dosent always connect to the acess points and when it does , and everything seems to be ok (even in network section of the system preferences ) when i go to safari for example it tells me that im not connected . I tried to connect the pc to my phone using hotspot , same problem in the pc it shows connected to network but in the phone the pc doesnt appear in the list of the connected devices . What to do ? Please help me !
       
    • By blackosx
      Vector themes for Clover are new and currently still under development. Setting out to re-create my BGM theme to vector I realised there was some learning needed in order to create a theme.svg file for Clover to use. As SVG files are text based, I quickly realised that they could be manipulated from the command line and looking at the Clovy theme I decided to break it down in to parts for creating other themes.
       
      As a result, I've been working on Clover SVG Theme Builder
      https://bitbucket.org/blackosx/cloversvgthemebuilder
       
      Current Version:
      0.4.5
       
      Overview
      The idea is to allow a theme designer to work on individual images and not worry about the required overall file structure which Clover expects. The designer can populate a Theme directory with a settings file and individual .svg files and let the script generate a final theme.svg file for using with Clover.
       
      I've created a basic sample theme to help demonstrate the script.
      https://bitbucket.org/blackosx/cloversvgthemebuilder/downloads/Theme.zip
       
      The Theme directory contains Adobe Illustrator and SVG files for each image in the required folder structure for the script.
       
      Using this sample theme, the script will generate this theme from the files.
       

       
      The idea is these can be used to build new themes and I'm currently using it to build my BGM_SVG theme.
       
      I can imagine far more complicated themes will be generated in the future, but for now I hope this may serve to help kickstart basic vector theme development.
       
      Notes:
      • Clover's SVG theme development is still underway and things are likely to change so this script and it's supporting template file will need to change with Clover.
      • I've only tested this using SVG files saved from Adobe Illustrator using the following settings, for files from other apps may need added support.



      • For the script to correctly inject SVG code in to the template, each SVG image must contain a group of elements.
      • Font files are currently not included in the final theme file but this can be an option.
      • In time, maybe other templates can be added which have different layouts??
       
      These are early days, so I'll update this post when necessary.
    • By zazman
      Bonjour,
       
      Depuis Catalina, l'extention Applebacklightfixup ne fonctionne plus. J'ai trouvé une solution en le supprimant de EFI/CLOVER/KEXT/OTHER/ et en gardant SSDT-PNFL.aml dans EFI/CLOVER/ACPI/Patched.
       
      j'ai pourtant plusieurs soucis :
      - le réglage de luminosité de l'écran ne reste pas toujours en mémoire d'une session à l'autre après un shutdown ou un restart (c'est aléatoire)
      - Le curseur de luminosité du panneau de conf affichage, lorsqu'il est positionné complètement à gauche met la luminosité de mon écran à zéro, donc tout noir... et c'est embêtant si je relache ma souris dans cette position !
      - Dans le paramétrage "clavier" du panneau de conf, onglet raccourcis, je n'ai pas d'item "affichage" pour afffecter le réglage de luminosité à F11 et F12 (ou à F2 et F3 sur mon toshiba satellite).
       
      J'ai essayé de mettre une valeur dans config.plist dans system parameters/backlight level. j'ai saisi 100, il m'a affiché 0x100, mais au redémarrage, mon écran restait noir. J'ai donc effacé cette valeur. Comment fonctionne ce paramétre et quelle valeur faut-il y indiquer ? Existe-il une solution plus propre sur Catalina 10.15.5 pour résoudre ces problèmes (j'utilise le CPU intel de mon toshiba satellite L50B - 1N2, pas le GPU radeon).
       

×