Jump to content
jesusrop

[SUCCESS] GA-H87M-D3H, i5-4670, GTX760, Yosemite 10.10.2, clover

1 post in this topic

Recommended Posts

I'm posting my build to both get suggestions on how to improve it (see what bothers me section below) and for reference to others with similar hardware.

I'm not an expert at all (it is my first successful build) so expect little extra knowledge from me than everything that is written here. Anyway, I'll check this thread from time to time to try to answer questions.

If I change anything, I'll try to reflect it here. Good luck!

 

Hardware

  • MB: GA-H87M-D3H
  • CPU: i5-4670
  • GPU: Gigabyte GTX 760 OC 2GBy
  • RAM: Kingston 8GBy (2*4GBy) (1x Kingston Black, 1x kingston HyperX)
  • Screen: 2x ASUS VS239
  • Sound: SoundBlaster surround omni external USB
  • Corsair CX750M PSU
  • Samsung SSD 840 EVO 120GBy
  • Seagate 500 GBy mechanical drive
  • Other SSD and seagate drives for windows
  • LG DVD drive
  • Logitech wireless desktop MK710

Software

  • OSX 10.10.2
  • Clover r3168. THX to the devs!
  • NVIDIA Web Driver 343.02.02f01 (native drivers work OK as well, but I have the feeling that I get better power management and also they are able to squeeze a few extra points from Luxmark)
  • Cuda driver 6.5.46
  • Creative SoundBlaster surround omni driver v13.1.03.47
  • Hackintosh Vietnam Tool 1.8.1 (for LAN kext and general help). THX to the devs!
  • The forbidden USB creator tool. THX to the devs!
  • HWSensors.6.13.1363.Binaries. THX to the devs!
  • Logitech Control Center 3.9.1

BIOS

  • Version: F10
  • Optimized defaults
  • XHCI handoff: enabled
  • EHCI handoff: enabled
  • XHCI mode: Auto (have not tested Smart Auto, others claim it works too)
  • Internal graphics: disabled
  • On-board audio disabled
  • C6/C7 state disabled
  • Internal parallel and serial ports disabled

What works (short answer: everything I need/use)

  • Sleep (native, ALWAYS 100% guaranteed to work. It is the reason I have different RAM sticks)
  • LAN (with external kext)
  • External sound card (native) (internal sound also works, but is trickier)
  • Graphics acceleration & multi screen (native)
  • Power management (native), 90% of the time works good enough, but:
    • I've seen the graphics card idling at top non-turbo speed a couple of times
    • CPU has only few states (8x, 34x,35x,36x,37x or something like that)
  • SSD trim (or at least it says so), with kext patch (see clover section)
  • App store (native)

What is not tested

  • USB 3.0 (have no devices, but with 2.0 devices the ports work just fine)
  • Messages.app
  • DVD unit. It opens and closes with the keyboard eject key, but I haven't loaded any disc nor tried to burn anything.

What doesn't work or bothers me

  • Have found nothing not working at least to some usable point
  • Sound was a bit buggy using toleda's patch, but you can get good sound most of the time with the clover version of the patch.
  • I need to place the lan kext RealtekRTL8111 in S/L/E. I can't leave it in the clover kexts folder. It just does not load if I do that.
  • The logitech keyboard layout from time to time breaks and I have to reinstall the entire OS. I will buy an apple keyboard when I have the money.
  • I don't understand how is hibernation handled. I marked NeverHibernate on clover config and the computer never hibernates (I don't miss hibernation at all, just want to understand)
  • I don't have a slider to adjust sleep time. I had to manually set it using pmset -a sleep 15
  • Due to having symlinked some home subfolders to the mechanical drive (see below) I lost the fancy icons :(
  • Bothers me that I lost a lot of time to get this thing running. Figuring the memory problem was especially hard.

Benchmarks (please if they are low, tell me how to improve them)

  • GeekBench (intel-32bit) test
    • Singe core: 3439
    • Multi core: 10972
  • Luxmark 2.1 sala: 574 (with native graphics drivers it was about 530)

How-to

  1. I created 2 USB drives:
    1. Clover only drive, following this guide, but skipping the part of copying the installer files to the drive. I also used the same EFI folder I use on my final build. SMBIOS MAC Pro 3,1, but same config as the final clover config. Anyway, in the past that guide gave me good results so you can follow it for installation.
    2. OSX installed in a different USB stick using the forbidden tool
  2. Boot from the clover USB and point it to the installer USB. Install OSX and reboot with the clover USB to the target partition
  3. Install clover on the target partition (see clover config section)
  4. Using Hackintosh Vietnam tool 1.8.1, I installed the LAN kext (indeed, I copied the kext in an earlier build from S/L/E and this time I just installed it with Kext Wizard)
  5. Put FakeSMC and all plugins from HWSensors.6.13.1363.Binaries into the EFI/clover/kexts/10.10 folder
    1. Copied also the HWMonitor app to the applications folder
  6. Installed the NVIDIA web driver (reboot required)
  7. Installed the Logitech Control Center (reboot required)
  8. Installed the creative sound driver
  9. Installed the Cuda driver
  10. Fix permissions and rebuild kext cache (several times during the process just in case)

Clover config

  • No DSDT
  • No SSDT
  • SMBIOS: iMac 14,2
    • in the clover USB i use Mac Pro 3,1 to be able to install the NVIDIA web driver without changing my settings. Both configs work fine, but I stick to iMac just because is closer to my hardware.
  • Kext patches (all from Vietnam Hackintosh Tool):
    • Trim
    • Second Stage patch 10.10
    • USB3 after sleep on intel
    • Disable ECC memory check on MacPro (guess I can remove this one)
  • EFI/CLOVER/drivers64UEFI
    • FSInject-64.efi
    • HFSPlus.efi
    • OsxAptioFix2Drv-64.efi
    • OsxFatBinaryDrv-64.efi
  • EFI/CLOVER/kexts/10.10
    • All kexts from HWSensors.6.13.1363.Binaries
  • config.plist:
    • I used clover configurator for editing this file.
    • I got this result with some trial and error.
    • Don't use Fix_HDA if you disable the integrated sound card.
    • Most ACPI fixes are just guesses. I just marked everything that was "AddXXX", "FixYYY" (if my system has YYY)
    • You can find it at the end of the post

Symlinking special folders

  • Why?
    • I have a small but speedy ssd and a "big" and slow mechanical drive. If I put my documents, pictures and music in the SSD... well, they simply don't fit.
    • I could move the entire home folder to the mechanical drive, BUT my Lybrary folder with all app settings and cache files will also move there slowing down everything
  • My solution has been to symlink the documents, downloads, pictures... folders to somewhere in my mechanical drive, and leave the home folder where it is supposed to be
  • How?
    • I googled it
    • With terminal in your home folder
    • sudo rm -rf Movies
    • ln -s "path to your mech drive mirror of user folders"/Movies/ "path to your home folder"/Movies
  • Does it work?
    • So far, the system is working as expected
    • Mail.app launches instantly (when I had the Library in the mechanical drive it took 5 to 10 secs). The system is a bit more responsive in app launch than before, when the app settings had to be grabbed from the mechanical drive
    • My folder icons are standard folders. Ugly. I don't know how to customize them again (i googled it, but I have no other folder with the standar icons to copy them from)

Clover config.plist

<?xml version="1.0" encoding="UTF-8"?>
<!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd">
<plist version="1.0">
<dict>
	<key>ACPI</key>
	<dict>
		<key>DSDT</key>
		<dict>
			<key>Debug</key>
			<false/>
			<key>DropOEM_DSM</key>
			<false/>
			<key>Fixes</key>
			<dict>
				<key>AddDTGP_0001</key>
				<true/>
				<key>AddMCHC_0008</key>
				<true/>
				<key>AddPNLF_1000000</key>
				<true/>
				<key>DeleteUnused_400000</key>
				<true/>
				<key>FIX_ACST_4000000</key>
				<true/>
				<key>FIX_ADP1_800000</key>
				<true/>
				<key>FIX_RTC_20000</key>
				<true/>
				<key>FIX_S3D_2000000</key>
				<true/>
				<key>FakeLPC_0020</key>
				<true/>
				<key>FiX_TMR_40000</key>
				<true/>
				<key>FixDarwin_0002</key>
				<true/>
				<key>FixDisplay_0100</key>
				<true/>
				<key>FixHPET_0010</key>
				<true/>
				<key>FixIPIC_0040</key>
				<true/>
				<key>FixLAN_2000</key>
				<true/>
				<key>FixRegions_10000000</key>
				<true/>
				<key>FixSBUS_0080</key>
				<true/>
				<key>FixShutdown_0004</key>
				<true/>
				<key>FixUSB_1000</key>
				<true/>
				<key>NewWay_80000000</key>
				<true/>
			</dict>
			<key>ReuseFFFF</key>
			<false/>
			<key>SlpSmiAtWake</key>
			<true/>
		</dict>
		<key>DropTables</key>
		<array>
			<dict>
				<key>Signature</key>
				<string>DMAR</string>
			</dict>
		</array>
		<key>SSDT</key>
		<dict>
			<key>DropOem</key>
			<true/>
			<key>Generate</key>
			<true/>
		</dict>
	</dict>
	<key>Boot</key>
	<dict>
		<key>Arguments</key>
		<string>nvda_drv=1 kext-dev-mode=1</string>
		<key>Debug</key>
		<false/>
		<key>Legacy</key>
		<string>LegacyBiosDefault</string>
		<key>NeverHibernate</key>
		<true/>
		<key>Secure</key>
		<false/>
		<key>Timeout</key>
		<integer>5</integer>
		<key>XMPDetection</key>
		<false/>
	</dict>
	<key>Devices</key>
	<dict>
		<key>USB</key>
		<dict>
			<key>AddClockID</key>
			<true/>
			<key>FixOwnership</key>
			<true/>
			<key>Inject</key>
			<true/>
		</dict>
	</dict>
	<key>GUI</key>
	<dict>
		<key>Custom</key>
		<dict>
			<key>Entries</key>
			<array>
				<dict>
					<key>Disabled</key>
					<false/>
					<key>FullTitle</key>
					<string>UEFI Internal</string>
					<key>Hidden</key>
					<string>Always</string>
					<key>Ignore</key>
					<false/>
					<key>NoCaches</key>
					<false/>
					<key>Type</key>
					<string>Other</string>
				</dict>
			</array>
		</dict>
		<key>Language</key>
		<string>es:0</string>
		<key>Mouse</key>
		<dict>
			<key>DoubleClick</key>
			<integer>500</integer>
			<key>Enabled</key>
			<false/>
			<key>Mirror</key>
			<false/>
			<key>Speed</key>
			<integer>8</integer>
		</dict>
		<key>Scan</key>
		<dict>
			<key>Entries</key>
			<true/>
			<key>Legacy</key>
			<false/>
			<key>Tool</key>
			<true/>
		</dict>
		<key>ScreenResolution</key>
		<string>1920x1080</string>
		<key>Theme</key>
		<string>mac</string>
	</dict>
	<key>Graphics</key>
	<dict>
		<key>Inject</key>
		<dict>
			<key>ATI</key>
			<false/>
			<key>Intel</key>
			<false/>
			<key>NVidia</key>
			<false/>
		</dict>
	</dict>
	<key>KernelAndKextPatches</key>
	<dict>
		<key>AppleRTC</key>
		<true/>
		<key>KernelPm</key>
		<true/>
		<key>KextsToPatch</key>
		<array>
			<dict>
				<key>Comment</key>
				<string>Enable USB3 after wake for Intel 8</string>
				<key>Find</key>
				<data>
				xoDIAAAAAQ==
				</data>
				<key>Name</key>
				<string>AppleUSBXHCI</string>
				<key>Replace</key>
				<data>
				xoDIAAAAAA==
				</data>
			</dict>
			<dict>
				<key>Comment</key>
				<string>Enable Trim on SSD</string>
				<key>Find</key>
				<data>
				QVBQTEUgU1NE
				</data>
				<key>Name</key>
				<string>IOAHCIBlockStorage</string>
				<key>Replace</key>
				<data>
				AAAAAAAAAAAA
				</data>
			</dict>
			<dict>
				<key>Comment</key>
				<string>Second Stage patch 10.10</string>
				<key>Find</key>
				<data>
				AQAAdRc=
				</data>
				<key>Name</key>
				<string>IOGraphicsFamily</string>
				<key>Replace</key>
				<data>
				AQAAdBc=
				</data>
			</dict>
			<dict>
				<key>Comment</key>
				<string>Disable ECC Memory in MacPro SMBIOS</string>
				<key>Find</key>
				<data>
				cgoATWFjUHJvNCwxAE1hY1BybzUsMQBY
				</data>
				<key>Name</key>
				<string>AppleTyMCEDriver</string>
				<key>Replace</key>
				<data>
				cgoAAAAAAAAAAAAAAAAAAAAAAAAAAABY
				</data>
			</dict>
		</array>
	</dict>
	<key>SMBIOS</key>
	<dict>
		<key>BiosReleaseDate</key>
		<string>09/03/2013</string>
		<key>BiosVendor</key>
		<string>Apple Inc.</string>
		<key>BiosVersion</key>
		<string>IM142.88Z.0118.B00.1309031249</string>
		<key>Board-ID</key>
		<string>Mac-27ADBB7B4CEE8E61</string>
		<key>BoardManufacturer</key>
		<string>Apple Inc.</string>
		<key>BoardType</key>
		<integer>10</integer>
		<key>ChassisAssetTag</key>
		<string>iMac-Aluminum</string>
		<key>ChassisManufacturer</key>
		<string>Apple Inc.</string>
		<key>ChassisType</key>
		<string>13</string>
		<key>Family</key>
		<string>iMac</string>
		<key>Manufacturer</key>
		<string>Apple Inc.</string>
		<key>Mobile</key>
		<false/>
		<key>ProductName</key>
		<string>iMac14,2</string>
		<key>SerialNumber</key>
		<string>C02KXKMRF8JC</string>
		<key>Trust</key>
		<false/>
		<key>Version</key>
		<string>1.0</string>
	</dict>
	<key>SystemParameters</key>
	<dict>
		<key>InjectKexts</key>
		<string>YES</string>
	</dict>
</dict>
</plist>

Share this post


Link to post
Share on other sites
Advertisement

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By fusion71au
      Clover r4961 ISO compiled with GCC and minimal config.plist compatible for use in VMWare Workstation.
       
      Tested with unlocked Workstation 15 running OSX 10.9 -->10.14 guest in Windows X64 host.
       
      Installation
      1. Download and unzip "EFI_Clover_r4961 for VMware.zip". Mount Clover-v2.4k-4961-X64.iso by double clicking on it.
      2. Mount your VM's EFI System Partition eg in terminal
      sudo diskutil mount disk0s1   3. Copy EFI folder from step 1 into the EFI partition
      4. Shutdown the VM, add bios.bootDelay = "3000" to your VM's vmx file
      5. Reboot your VM, press <F2> to access the VMware Boot Manager and add CLOVERX64.efi to the boot menu.
       
      Substitute your own unique and valid MLB and ROM variables in the /EFI/CLOVER/config.plist (Rt Variables section) to activate iMessage/Facetime on your VM.
    • By gengik84
      Ciro82==>>Thanks
      Uno dei tre Requisiti:
      Hack funzionante Mac vero Macchina virtuale Impostazioni Bios per il boot:
      Cercate una voce  del tipo “Sata Mode”e settatela  in AHCI
      Secure Boot: disabilitare o altri sistemi operativi
      CSM: UEFI o LEGACY, oppure a secondo del tipo di installazione
      VT-x / VT-d disable
      *Nota: Secure boot e csm valido solo per bios UEFI
      Materiale Occorrente 
      "OS X (Versione App.Store)”
      USB 8GB  *nota: nel caso di usb superiori dovrà essere partizionata, in modo da avere una partizione su cui "lavoreremo,di questa dimensione
      ShowAllfiles 
      kext Wizard 
      Bootloader Clover_2.3k_r xxx:                   http: //sourceforge.n.../cloverefiboot/
      Clover Configurator:                                    http: //mackie100proj...a.org/download/
      FakeSmc.kext:                                            https://github.com/kozlek/HWSensors/releases
      In allegato,a fondo pagina troverete un "pacchetto" contenente : ShowAllfiles, Kext Wizard, FakeSmc.kext: 
      App alternative:
      ESP Mounter Pro: per montare la partizione EFI
      Vi illustrerò tre metodi per creare la usb, ma sono ben distinti… quindi usatene soltanto uno
      Metodo 1: “Install Mac_OS_X.command” Metodo 2: “Create Install Media di Apple” Metodo 3:  Metodo Manuale Alla fine delle preparazione dell’installer, tutti i metodi necessitano l’installazione del Bootloader Clover sulla a vostra USB.
      “CONDIZIONI OBBLIGATORIE”
      PUNTO 1: che la vostra usb sia stata preventivamente nominata USB (caratteri maiuscoli) Tabella di partizione GUID e la formattazione in  Mac esteso Journaled.
      PUNTO 2: che l’installer di OSX si trovi in Applicazioni
      Utility Disco 
      Selezionate la pendrive, andate su “partizione”, selezionate “1 partizione”, impostate Mac OS esteso journaled e date il nome USB, poi in basso cliccate su opzioni e scegliete Tabella partizione (GUID), poi “applica”.
      Immagine 
      Riporto nuovamente l’operazione sopra citata adoperando dal nuovo Utility Disco introdotto su El Capitan.
      Rimane ovviamente invariato nome della usb in ==>> USB (maiuscolo), la formattazione in Mac esteso Journaled e sia la mappa partizione in GUID
      Da utility disco selezionate la usb, cliccate su inizializza.
      dal menù a tendina scegliete la relative impostazioni
      Immagine  
      Procedura effettua da High Sierra è la stessa della precedente, l'unica attenzione e operazione da aggiungere in primis  è cliccare nel menù a tendina in alto sulla sinistra di utility disco e selezionare "mostra tutti i dispositivi"
      Immagine 
       
      =====================
        METODO 1: "Install_Mac_OS_X.Command" Lo script che trovate allegato in fondo alla guida permette la creazione dell’installer in maniera automatica
      Include la possibilità di scelta di tre versioni di osx
      Yosemite El Capitan Sierra Il risultato finale è come quello del metodo "manuale" descritto nella guida, per cui l'installazione avverrà in un solo passaggio, non in due come con il metodo createinstallmedia. 
      Offre inoltre la possibilità di inserire un kernel patchato, utile, per esempio, per chi usa AMD.
      Rimane invariato il nome dato alla usb in USB, mappa partizione e tipo di formattazione
      Se la vostra usb non sarà rinominata nel modo corretto, verrete avvisati dal terminale, quindi non dovrete far altro che apportare la relativa modifica e rilanciare nuovamente lo script
      Esempio
      ===========================
      Metodo 2 
      L'intento è quello di usare la procedura fornitaci direttamente da Apple, "createinstallmedia", introdotta  con Mavericks. 
      Tale metodo prevede l’uso del terminale che via via se ne sta perdendo il “valore e l’uso”
      Inizialmente per i neofiti potrà sembrare problematico ma alla fine non è così.
      Durante il post installazione alcune operazioni ne richiedono l’ uso.
      Perciò mi sono chiesto perchè, qualora uno volesse, non far conoscere da subito un po’ questo “strumento”???
      Per favorirvi vi ho allegato i comandi già  “pronti”, i quali li potrete copiare ed incollare sul terminale.
      A questo punto aprite il terminale, copiate ed incollate il comando sottostante e premete invio, digitate la vostra password e premete nuovamente invio.
      Comando per creare USB con Yosemite:
      sudo /Applications/Install\ OS\ X\ Yosemite.app/Contents/Resources/createinstallmedia --volume /Volumes/USB --applicationpath /Applications/Install\ OS\ X\ Yosemite.app --nointeraction  
      Comando per creare USB con El Capitan
      sudo /Applications/Install\ OS\ X\ El\ Capitan.app/Contents/Resources/createinstallmedia --volume /Volumes/USB --applicationpath /Applications/Install\ OS\ X\ El\ Capitan.app --nointeraction Comando per creare USB con Sierra 
      sudo /Applications/Install\ macOS\ Sierra.app/Contents/Resources/createinstallmedia --volume /Volumes/USB --applicationpath /Applications/Install\ macOS\ Sierra.app/ --nointeraction Per creare USB con Hight Sierra o Mojave usate --> C_I_M (aggiornato per 10.14)
       
      Funziona con il drag & drop sul terminale, in questo caso non vi è necessità che la usb sia nominata in un determinato modo ed essendo basato su create install media ovviamente funziona da 10.9 a 10.14.... 
      BENE…IL PROCESSO DI CREAZIONE E’ INIZIATO…
      AVREMO CIRCA 20/30 MINUTI DI TEMPO LIBERO A CUI DEDICARSI A CIO’ CHE VOGLIAMO………………………………………..  
      COLGO L’OCCASIONE PER FARVI NOTARE LA VELOCITA’ E LA SICUREZZA DI QUESTO METODO
      CONFRONTATE QUESTO CON IL TERZO METODO E NOTERETE CHE CON UN SOLO PASSAGGIO, OSSIA IL COMANDO DATO AL TERMINALE, FACCIAMO IN UNA SINGOLA OPERAZIONE TUTTI I VARI STEP DESCRITTI SULL’ ALTRO METODO.
      DETTO QUESTO, MOLTO IMPORTANTE E’ SOTTOLINEARE CHE COSI’ FACENDO EVITEREMO ERRORI  DI DISTRAZIONE RIGUARDO AI PASSAGGI O FRAINTENDIMENTI.
      Immagine 
      Potete adesso passare ad installare il bootloader Clover sulla vostra usb.
      *NOTA*:
      Avendo usato questo metodo l'installazione si dividerà in due fasi, perciò dopo il primo riavvio e necessario far partire nuovamente l'installer, selezionare lo stesso disco senza formattarlo.
      Finita questa ulteriore fase , l'installazione sarà terminata
      =========================
      METODO "MANUALE"....  (lascio per futura memoria-Compatibile fino a 10.12)
      ==========================
      Bootloader
      **Nota:** Installazione in UEFI  dipenderà dalla scheda madre in vostro possesso, quindi se non supporta tale opzione , il bootloader dovrà essere installato in  modalità Legacy.
       Vi invito, qualora non sapeste questa informazione, a recarvi nel sito ufficiale del produttore e controllare le informazioni a riguardo
      Fatto questo dobbiamo installare  Clover sulla usb.
      A seconda del tipo di Bios o al tipo di installazione che vogliamo fare UEFI o Legacy avremo ovviamente configurazioni diverse in questa fase.
      Lanciate il pkg.
      Immagine 

       
      Cambiate la destinazione di installazione ad USB oppure Install Mac_OS_X (a secondo del tipo di creazione eseguita)
      Successivamente clicchiamo su "Ad Hoc"
      Per Installazione UEFI
      Mettete i flag   : Installazione solo per avvio UEFI
                               : installare Clover nella ESP
                               : Driver64UEFI  AptioMemory --> (consigliato) 
                               : Driver64UEFI  ApfsDriverLoader --> (consigliato) --> sostituisce l'uso del driver apfs.efi
                               : Selezionate l'altri driver come da successiva immagine,
       
      *Nota: Altri driver che si possono usare  al suo posto  sono:
       informazioni 
       
      Proseguite con l’installazione.
      Immagine 
      ** Ricordate che avrete accesso a questa cartella dopo aver montato la partizione EFI**
      ===========================
      Per installazione Legacy
      Immagine 
      ===========================
      Impostazione per config.plist:
      Con clover configurator “montate” la partizione EFI della usb.
      1) Per fare questo nel menù di sinistra, cliccate su “Mount EFI”
      2) individuate la partizione relativa alla vostra usb, a questo punto montiamo la relativa partizione EFI  selezionando l’apposito pulsante “Mount Partition”
      Immagine 
      3) Successivamente cliccate su “Open Partition”.. recatevi in EFI/Clover ed aprite il config.plist
      4) Sezione ACPI: Disabilitate tutti i fix sia del menù 1 che del menù 2
      Immagine 
      5) Sezione BOOT: Sole se si sta installando Yosemite mettete il flag su kext-dev-mode=1
      Immagine 
      6) Sezione RT Variables: Se si sta installando El Capitan oppure Sierra, aggiungere i valori: BooterConfig= 0x28, CsrActiveConfig= 0x67
      Immagine 
      7) Sezione System Parameters: Su inject kext mettete YES
      Immagine 
      ===========================
      Nota: Su El Capitan, è stato introdotto SIP (System Integrity Protection)
      Info:
      ===========================
      Recatevi in EFI/Clover/kext/10.x 
      X= alla versione di osx che state installando. Per esempio se installerete Yosemite dovrete recarvi nella cartella 10.10, con El Capitan in 10.11….ecc
      Se non ci fosse tale cartella, createla e nominatela voi a “modo”.
      Copiatevi all’interno FakeSmc.kext
      *Nota se venite già da altre vostre configurazioni, oltre kext sopra citato ,potete mettere gli altri necessari per il vostro hardware
      Stessa cosa se avete DSDT e/o SSDT potete copiarli in EFI/Clover/Acpi/Patched
      Immagine 
      
      Per High Sierra:
      Scaricare il driver apfs.efi a fine guida, collocarlo:
          --> EFI/clover/Driver64UEFI se stiamo usando UEFI
      --> EFI/Clover/Driver64 se stiamo usando Legacy
       
      Per chi volesse continuare ad usare HFS vi rimando a questo post:
        Come installare High Sierra in HFS direttamente dalla usb  
      Utenti Laptop:  Nel 99% è obbligatorio disattivare la grafica discreta Nvidia/Amd per installare questo nuovo osx
                                     Quindi aggiungete --> SSDT-Disable_DGPU.aml.zip
                                     in EFI/Clover/acpi/Patched della usb
      --------------------------------------------------------------------
      Per Mojave:
      Scaricare il driver apfs.efi per 10.14 a fine guida, collocarlo:
          --> EFI/clover/Driver64UEFI se stiamo usando UEFI
      --> EFI/Clover/Driver64 se stiamo usando Legacy
      Versione di clover non antecedente a V_4015
      Volete usare HFS?
      E' possibile fare un installazione diretta su altro disco o partizione, nel caso può essere usato anche per effettuare aggiornamenti...
      nel caso guardate...
       Mojave in HFS 
       Oppure direttamente da usb  
       
      Fatto questo avrete la vostra USB bootable per installare OSX.
      ………Non scordatevi Fakesmc.kext da mettere nella relativa cartella…. senza il quale non farete mai il Boot......
      *NOTA: se usato il terminale per la creazione della usb, l'installazione si dividerà in due fasi, perciò dopo il primo riavvio e necessario far partire nuovamente l'installer, selezionare lo stesso disco senza formattarlo.
      Finita questa ulteriore fase , l'installazione sarà terminata
      **NOTA** Se avete processori Broadwell,Skylake o Kabylake...usate FakeSmc.kext e relativi sensors che trovate all'interno del secondo pacchetto.. (potete usarlo anche sui precedenti senza problemi, essendo una versione più aggiornata ha ulteriore supporto per le cpu più recenti)
      Update: Fakesmc e sensors versione 6.26
      Post installazione... post #2           
       Buon Hack….. 
      Aggiornamento:Install_Mac_OS_X.command.zip (compatibile da 10.10 a 10.12)
      le info le trovate a questo post
      Ringrazio @Ciro82 che mi ha aiutato nel preparare questa guida.
      Pacchetto.zip
      Pacchetto-2.zip
      Pacchetto-Fake+Sensors 6.26.1440.zip
      C_I_M.zip
       
      apfs.efi-10.14-beta1_No_Log.zip





       

    • By kushwavez
      Acer Aspire V15 V5-591G - Mojave 10.14.5
       
      (Note: mine is 55TU version, but the bootpack will work fine with another versions of 591G, for example: V5-591G-71K2, -764Z, -59PU, etc.)
      Specifications:
      - Motherboard: USOPP_SLS (Skylake-H PCH)
      - BIOS:Insyde Corp. v 1.15
      - CPU:Intel Core i5-6300HQ 2.3 GHz (Skylake)
      - GPU: NVIDIA GeForce GTX 950M 2 GB (Optimus) & Intel HD Graphics 530
      - RAM:SK hynix 4 GB DDR4 (Later I bought + KINGSTON 4 GB) 2133 MHz
      - WiFi + Bluetooth:Qualcomm Atheros QCNFA344A 5 GHz (Later -> Broadcom BRCM94352Z M.2 5 GHz WiFi + 4.0 Bluetooth)
      - Audio:Realtek HD Audio: ALC 255 
      - Ethernet: Realtek RTL8168/8111
      - Card Reader:Realtek USB 2.0 Card Reader (USB2.0-CRW)
      - Webcam:HD Webcam
      - HDD:TOSHIBA MQ01ACF032 320 GB HDD
      - SSD:SPCC M.2 230 GB SSD
      - Display:1366x768 (15.6", Matte)
      - Battery: 6 cell 56Wh / 5040mAh
      - Connectors: 
      1x SD Card Reader 2x USB 3.0 (1x USB Charging), 1x USB 2.0 1x VGA 1x HDMI 1x 3.5mm microphone/audio combined jack connector 1x Ethernet (Rj-45) - Keyboard & Touchpad:Multi-Touch & Multi-gestures ELAN 501 Touchpad, Backlight Keyboard.
      Working:  
      - Wi-Fi (with BCM94352Z)
      - Bluetooth hand-off (With BCM94352Z)
      -Full Graphics enabled on HD 530: ig-platform-id: 0x191b0000 (HD 530 Mobile)
      - Display: if default colour profile is corrupted (blue is not actual blue but purplish) Use "Rec. ITU-R BT. 709-5" Color Profile (System Pref. -> Displays -> Color)
      -HDMI & VGA Outputs: AppleGraphicsDevicePolicy.kext Clover patch
      - Audio (ALC 255):(Internal Speakers, Internal Microphone, Headphone jack with AppleALC, ALCPlugFix -> layout-id=17)
      - Ethernet Realtek 8168/8111: RealtekRTL8111.kext
      - App Store, Messages, FaceTime, Siri, iCloud(native)
      - Integrated webcam(native)
      - 3.0 USB (native)
      - Touchpad and Keyboard(ELAN501): Fn keys are good, the weird thing is the Brightness key. On my keyboard it's Pause Break:Br-up, Fn+F12:Br-dwn-> To fix this try Karabiner (VoodoPS2Controller.kext), - for gestures try SmartTouchpad drivers
      - Battery info:Install ACPIBatteryManager.kext with Kext Utility or other installer.
      - Sleep Mode
      - SSD with TRIM enabled (to enable trim, open Terminal and write "sudo trimforce enable")
      Not working:
      - Original Wi-Fi (Qualcomm Atheros QCNFA344A):  unsupported, you need switch to BCM94352Z or just use a mini usb wifi dongle.
      - NVIDIA GeForce GTX 950M: Optimus not supported.
      - Card Reader: Unsupported -> Can't really fix because I don't have any SD Card at the moment, maybe can be fixed by adding Prod & Ven IDs to AppleStorageDevices.kext, I never used it anyway. name: "USB2.0-CRW" Prod ID: "0x0129" Ven ID: "0x0bda  (Realtek Semiconductor Corp.)"
      For Wi-Fi:
      - 1st method:You can choose an external USB wifi dongle (I used TP-Link Archer T1U (5GHz support), TP-Link has official macOS drivers, you just need to install it
      -2nd and I think the best method:Replace your M.2 Qualcomm Card with a compatible BCM94352Zcard (you will have hand-off Bluetooth too), just install the kexts (enabled with BrcmFirmwareData.kext, BrcmPatchRAM2.kext, FakePCIID.kext, FakePCIID_Broadcom_WiFi.kext, they're all in my attached zip). You could buy this card from ebay, aliexpress, or amazon
       
      Issues:
      - None
      BIOS Settings:
      - BIOS version 1.15 (irrelevant)
      - Secure Boot: Disabled
      - Touchpad: Advanced
      - Boot mode:UEFI
      Getting ready for Installation:
      - Download the install zip (bootpack & postinstall): Click here -> acer_aspire_v591g_installfiles.zip
      Installation:
      - Create an installer with any method you know (- Mac: createinstallmedia - Windows: Transmac, Vmware, Win32diskimager)
      - Copy my Clover folder to the USB's EFI folder
      - Boot with the Installer USB
      - If you stuck in boot, reboot and in the Clover bootloader select "config_debug.cfg" -> you'll have more informations about the freeze
       
      Please open the README.rtf in my install zip for more informations about the USB Installer & Post installation!
      If you have a single RAM and getting panic at boot, then you need to edit the "config.plist" with these (SMBIOS->after "Version 1.0"):
      ->Edit "Frequency" and "Size" to match your RAM values
      <key>Version</key> <string>1.0</string> <key>Memory</key> <dict> <key>Channels</key> <integer>1</integer> <key>SlotCount</key> <integer>1</integer> <key>Modules</key> <array> <dict> <key>Slot</key> <integer>0</integer> <key>Size</key> <integer>8192</integer> <key>Frequency</key> <integer>2133</integer> <key>Type</key> <string>DDR4</string> </dict> </array> </dict> </dict>  
      PowerManagement  fix:
      Set HWPEnable=YES in Clover (already set), CPUFloor to "700", Frequency to "2300" and "3200"(Normal and Turbo, if you have i7-6700HQ version then it should be "2600", "3500") and "FrequencyVectors" from "0x0d000000" to "0x07000000" in "S/L/E/IOPlatformPluginFamily.kext/Contents/PlugIns/X86PlatformPlugin.kext/Contents/Resources/Mac-A5C67F76ED83108C.plist", MSR _xcpm_idle Patch to KernelToPatch in Clover (If you have High Sierra, change "MatchOS" to 10.13):

      <key>KernelToPatch</key> <array> <dict> <key>Comment</key> <string>MSR 0xE2 _xcpm_idle instant reboot(c) Pike R. Alpha</string> <key>Disabled</key> <false/> <key>Find</key> <data> ILniAAAADzA= </data> <key>MatchOS</key> <string>10.14</string> <key>Replace</key> <data> ILniAAAAkJA= </data> </dict> </array> Reboot, and it's 800MHz in idle state, same on Windows.
       

       
      Elan SmartTouchpad
      I only use scrolling, one-, double- & tripletap
      If you want to try other gestures go to this link for more informations, options (v4.7 beta 5) ->  DETAILS ABOUT THE SMART TOUCHPAD DRIVER FEATURES
      Fn Brightness keys not working with this, tried several things without success. With VoodoPS2Controller it's working, but you'll have no gestures (neither scrolling).
       
       
      Before updating to a new version of Mojave please update kexts (and clover if necessary) to newer versions to avoid kernel panics.
      Generate a serial number with Clover Configurator.app (open up your config.plist with CC then -> SMBIOS -> Serial Number -> Generate New)
       
      Mojave & Windows 10 Dual-Boot:
      Dual-boot clean install (on one drive), UEFI Only:
       
       Boot into your Mac installer, Create 2 partitions in GUID table (1 for Win (I used FAT32 but I think it doesn't matter what you choose), 1 for Mac),   Install Mac, boot with your USB, mount your EFI partition (use terminal or an EFI mounter app), create an EFI folder (if there is no folder), copy the CLOVER folder I attached to the EFI folder, restart,  Boot into your Win installer, Format the partition you created for Win, install.   Now, it's automatically booting into Windows. To use Clover open cmd in administrator, type:  bcdedit /set {bootmgr} path \EFI\CLOVER\CLOVERX64.efi       5.  You're done! It will booting into Clover when you start the system, and you can select Win or Mac (or another OS if installed on a 3rd partition).
       
      Dual-boot with Windows installed first (on one drive), UEFI Only:
      If you already have Windows and you don't want to lose all your data there is a hope:
      I created a video from this restore method: [Hackintosh] Dual-Boot High Sierra & Windows - when Windows already installed - no data waste - UEFI
      You need bootable Mac Installer and a full system restore image (link is in my video's description).
      (You may see errors if your EFI partition is not 200 MB)
       Boot into your Windows, resize your partition or create one for Mac.  Boot into your Mac installer and in Disk Utility format the partition you created.  Restore from image: select your full system restore image.  When it's finished restoring you just need to restart, then boot to the system with your usb.  When you successfully booted to Mac desktop, mount your EFI partition (use terminal or an EFI mounter app), open EFI, you will see there is a Microsoft folder already (don't touch that!). Copy my CLOVER folder to the EFI folder then Restart.  Now, it's automatically booting into Windows. To use Clover open cmd in administrator, type:  bcdedit /set {bootmgr} path \EFI\CLOVER\CLOVERX64.efi       7.  You're done! You can select your old Windows and your new macOS!
      (Only tried with Windows 8/8.1/10. I don't know Windows 7,etc.)
       
      IF YOU GETTING ERRORS DURING MAC RESTORE:
      - Make sure you have partitions in GPT
      - Windows using 100 MB EFI and will annoy the Mac restore. Don't worry, just ignore the errors.
       
      IF YOU GETTING ERRORS DURING WINDOWS INSTALLATION (could not be formatted, etc):
      - Make sure you have GPT partitions, and GPT (UEFI) installer, also disconnect all external storage drives (except the installer USB)
       
      IF YOU USED RESTORE METHOD THEN CAN'T MOUNT YOUR EFI PARTITION (No EFI partition found):
      - It's because your EFI is not 200 MB or not an "Apple" original EFI,  but do not worry, try another EFI mounter, or mount from terminal (I used EFI mounter v3: Getting errors, but you can mount and use without problem)
      - You also could "mount" the EFI from Windows:
      1st method: open cmd in administrator mode and type:
      diskpart
      list vol (Now select the "System" volume,(FAT 32) For example I select 4)
      sel vol 4
      list part(Select System type partition, for example 2)
      sel part 2
      assign letter=b(This will "mount" your EFI partition)
      Open Explorer++ or TotalCommander in administrator mode to manage EFI
      remove letter=b (This will "unmount" your EFI)
      2nd method: open cmd in administrator mode and type:
      mountvol b: /s (This will mount your EFI)
      Open Explorer++ or TotalCommander in administrator mode to manage EFI
      mountvol b: /d (This will unmount your EFI)
      Thanks to all OSXLatitude members for helping me out! (Jake Lo, Hervé, Bronxteck, black.dragon74)!
      Notes:
      2019.06.05: Updated to 10.14.5 -> no problem when/after installing
      2019.04.25: Optimized touchpad scrolling -> updated install files
      2019.03.30: Fixed USB 3.0 ports, fixed Bluetooth crashes after sleep -> updated bootpack
      2019.03.28: Updated to 10.14.4. Unexpected crashes while updating to 10.14.4 -> fixed by updating Clover to the latest (v4910) version. Bluetooth crashes appeared -> fixed by downgraded Brcm*.kexts. Updated bootpack.
      2019.02.24: Bluetooth crashes after sleep -> fixed, updated bootpack. 
      2019.02.22: Updated to 10.14.3. Fixed HDMI Audio by installing "FakePCIID_Intel_HDMI_Audio.kext" -> fixed freezing during boot. Fixed brightness levels by installing "AppleBacklightFixup.kext". Also updated bootpack & postinstall zip down in attachments.
      2019.01.21: Removed FakeSMC.kext, SMCHelper-64.efi, replaced by VirtualSMC.kext, VirtualSMC.efi because I got random freezes when booting system (kextd stall[0], (120s): 'AppleACPICPU' -> CPU is at 100%, fans are spinning fast), also updated bootpack in the attachments "acer_aspire_v591g-55tu_clover.zip"-> Freeze continued, brought back FakeSMC, deleted VirtualSMC (caused BT crashes).
      2019.01.18: HDMI Audio is fixed, I didn't do anything HDMI Audio is not fixed, sometimes it worked but most likely not. (no idea why)
      2018.12.09: Updated to 10.14.2 -> did without any complication
      2018.11.28: Fixed combo-jack garbage sound output by installing ALCPlugFix and CodecCommander.kext
      2018.11.01: Updated to 10.14.1 -> HDMI & VGA ports are gone again. -> Fixed by "AppleIntelSKLGraphicsFramebuffer.kext" rollback from 10.14.
      2018.09.28: Updated to Mojave 10.14 -> Fixed HDMI & VGA Outputs by adding "AppleGraphicsDevicePolicy.kext" patches to config.plist, HDMI audio not working
    • By cvad
      View File Bootdisk Utility
      Make bootable USB Flash Disk for MAC OS X with Latest Clover bootloader revision fast and easy by one click! under OS Windows.
      Special utility from cvad & russian MAC community for new hackintosh users.
       
      Enjoy...
       
      For more information and complete instructions please see this topic.
       
       
       
       
      Feel free to "Rate File"
      Submitter cvad Submitted 04/28/2013 Category Bootloaders  
×