Jump to content
zhuzhu881

[Solved] the booting stop in "root device uuid is 'UUID'"

7 posts in this topic

Recommended Posts

Hi guy,

 

I am trying to install Os X 10.9.2 in my new installed PC, the installation is completed, and I have installed Clover in the HDD EFI partition. but while I was trying to boot it with UEFI, it is not able to boot when I am trying to boot it via latest version Clover R2652. facing message "root device uuid is 'UUID'"

 

It could be booted from the Clover built with  http://bbs.pcbeta.com/viewthread-1483106-1-1.html  (Chinese BBS)

the clover version in that pre-build Clover is not up-to-date

 

My PC hardware is

  • Gigabyte Z87x-UD5h
  • Intel i5 4670K
  • Hd4600 Graphic card with 1G ram

 

what i tried:

  1. try my configuration with Clover Configration Tool to build my config.plist and enable to PMPatch of Clover.
  2. update the BOIS version from F8 to the latest F9
  3. try to disable Vt-D in the BOIS setting, but it is grayed out, and unable to be changed to Disable
  4. search  in my regional Chinese forum and this one, did not find solution excepts PMPatch the BOIS file
  5. try PMPatch but i am unable to patch it, which i post my message in that topic
  6. try to boot "without cache" in Clover option when boot
  7. install some kernels include the latest FakeSMC

the issue is not solved

I have attached the plist flles and the screenshot

 

Please help,   thank you for advance.

 

 

update:

Created a new Install image from 10.2.9 install.app.  with no additional driver/kext, except the latest FakeSMC

but i can not boot the OS with the latest Clover(default setting with no editting)... with the same issue, but i can boot the new installed OS with the clover provide with http://bbs.pcbeta.com/viewthread-1483106-1-1.html

 

 

 

UPDATE(Solution): 

 

I can move ahead and successfully boot into OSX now.
 
Previously, there are only 3 drivers in /EFI/Clover/driver64UEFI/
I move the default installing drive to another folder to backup and then  copy drives from the previous version of Clover drivers64UEFI folder.
Now, there are 6 kexts in that folder of EFI
 
FSInject-64
HFSPlus
OsxAptioFixDrv-64
OsxFatbinaryDrv-64
PatitionDxe-64
VBoxHfs

post-1334861-0-00116200-1397973469_thumb.jpg

Report.txt

config.zip

Edited by zhuzhu881

Share this post


Link to post
Share on other sites
Advertisement

What drivers are u using for clover?

are u booting UEFI or legacy ?

thank you for asking

 

I am trying to boot with UEFI. 

and i just erase the HDD. and  create a new installing image with the 10.9.2.app, with no additional driver/kext(but latest FakeSMC.kext), but i met the same issue 

Share this post


Link to post
Share on other sites

thank you for asking

 

I am trying to boot with UEFI. 

and i just erase the HDD. and  create a new installing image with the 10.9.2.app, with no additional driver/kext(but latest FakeSMC.kext), but i met the same issue 

As i see u didnt answer the question..

Again same.

What drivers are u using for clover?

Check your drivers64uefi folder and see if u have aptiofix driver or not.

list all that u have in that folder.

Share this post


Link to post
Share on other sites

As i see u didnt answer the question..

Again same.

What drivers are u using for clover?

Check your drivers64uefi folder and see if u have aptiofix driver or not.

list all that u have in that folder.

@xpamamadeus

Just wanna say thx to you.

I can move ahead and successfully boot into OSX now.
 
Previously, there are only 3 drivers in /EFI/Clover/driver64UEFI/
I move the default installing drive to another folder to backup and then  copy drives from the previous version of Clover drivers64UEFI folder.
Now, there are 6 kexts in that folder of EFI
 
FSInject-64
HFSPlus
OsxAptioFixDrv-64
OsxFatbinaryDrv-64
PatitionDxe-64
VBoxHfs
 
let me update this topic for that issue.
Thank you again. :lol:

Share this post


Link to post
Share on other sites

 

@xpamamadeus

Just wanna say thx to you.

I can move ahead and successfully boot into OSX now.
 
Previously, there are only 3 drivers in /EFI/Clover/driver64UEFI/
I move the default installing drive to another folder to backup and then  copy drives from the previous version of Clover drivers64UEFI folder.
Now, there are 6 kexts in that folder of EFI
 
FSInject-64
HFSPlus
OsxAptioFixDrv-64
OsxFatbinaryDrv-64
PatitionDxe-64
VBoxHfs
 
let me update this topic for that issue.
Thank you again. :lol:

 

delete VBoxHfs since u have HFSPlus

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By Gymnae
      Introduction
      The H370 chipset powers 8th generation Intel Core-i CPUs. Even though the name H370 rings comparable to Z370, the H370 is based on newer silicon. This it also requires some new approaches compared to the Z370. An example would be on-die USB 3.1 and WiFi support.
       
      Since this guide is not a "hold-your-hand-every-step" guide, I assume you know:
      Clover installation and configuration How to create an install medium for MacOS Access and configure the BIOS Have heard of ACPI patching (I'm a newb at this myself)  
      What works
      Sleep (via DSDT edits and emulated NVRAM) On-board Audio (via AppleALC and native AppleHDA) Native power management (without any kext or patch) All USB ports (and only those present are active) iGPU for both acceleration and display dGPU (I'm running an Nvidia GTX 1080)  
      Untested
      NIC --> I'm using WiFi only  
      What doesn't work
      Native NVRAM via AptioMemoryFix.efi DMVT Pre-alloc higher than 64MB (but not necessary)  
      Community additions
      User @Panzerschiffe added a helpful post, altering this guide for user with AMD cards and not needing on-board sound.
      He also runs Mojave, which I don't run yet.
       
       
      Changes to the guide:
      22.5.18: Added SSDT hot-patching to enable sleep, replacing DSDT static patching as an alternative.
      23.5.18: Add iMac18,1 as alternative SMBIOS config for those relying on the iGPU for output
      25.6.18: Added update info
      28.8.18: Small changes for clarity, changed info for afps loading & updated USB patch for 13.6
      04.10.18: Update to Mojave will come once Mojave is more mature
      02.12.18: Removed unnecessary patches, fakepciid and audio patch method & linked to AMD post & added whatevergreen.kext as replacement for previous GPU kexts
      02.03.19: Removed unnecessary fakeid and ig_platform_id injections, ACPI patches - this is all handled by whatevergreen & lilu. In testing is a Framebuffer patch, see this post.
      04.03.19: Added Germany keyboard layout and updated pre-patched DSDT.aml removed DSDT patching
       
       
      1. Installation
      This guide heavy inspired by the work of /u/corpnewt of /r/hackintosh and his (sorta) Vanilla guide
       
      1.1 Create the install media for MacOS
      Follow this, if you are using a Mac to start off with. If you are totally new to MacOS, then please check the basic guide Creation of an installer media in windows or linux
       
      1.2 Install Clover on the install media
      Using the Clover installer, ensure you are installing to the USB medium you are using for the installer.
      Chose the following options, leaving the others on default: 
       
      UEFI driver: AptioMemoryFix UEFI driver: ApfsDriverLoader UEFI booting only Install to ESP  
      You have to get your hands on an apfs.efi. A google search can help, or extracting it from the Installer package. Make sure you procure a version matching the MacOS version you are about to install. Place the apfs.efi in drivers64UEFI.
       
      1.2 Adjust the config.plist for the installer
      You can use the config.plist attached as a guideline, but take a look at it before and at least adjust the SMBIOS - otherwise it won't boot.
      Attention: The attached plist contains audio patches introduced by a post-install step. If you run into problems, you might remove those. It also contains a manual slide value, which should normally not be needed, but works fine for me. It is also tuned for usage with an Nvidia Pascal dGPU as main GPU.
       
      The config you create now should serve you nicely for install and running the system.
       
      Take care of adding the following basics:
      SMBIOS: iMac18,3 - You can generate a serial number via Clover Configurator. The creation of a proper SMBIOS is covered in many guides to good extend Note: If you aim at using the iGPU for output, a user reported that iMac18,1 works better - since iMac18,3 produces severe flicker. I'm now also testing 18,1 Look at the graphics section and adjust the injection for Intel to your situation  
      Fixes

      Patches

      Devices

      Graphics
      Important:
      Change 0x59120003 to 0x59120000 if you don't use a dGPU as your main display Driver and instead use the iGPU for output.
      Also note. SMBIOS iMac18,1 has been reported to work better in this configuration. But 18,3 works fine for me.

      Kernel and Kext patches
       
      1.3 kexts and friends
      Add the supplied SSDT-UAIC.aml to "patched" - it limits the injected USB Ports to the actual number and ports valid for this board.
       
      Required kexts on "Other":
      FakeSMC.kext Whatevergreen.kext Lilu.kext AppleALC.kext IntelMausiEthernet.kext in case you're running Ethernet USBInjectAll.kext with the HCI-300-series-injector.kext --> These two should be installed to /L/E after install  
      We are leaving sound out at the moment, this is something for post-install.
       
      1.4 Check BIOS and install
      You should be ready for install. But before you reboot, please take a look at your BIOS and set it up accordingly (copied from the aforementioned guide and adapted):
      Load Optimized Defaults Disable VT-d setting If your system has Secure Boot Mode, disable it Enable CSM - This is sometimes needed to dual screens to work Set OS Type to Windows 8/10 or OtherOS - I have not seen a difference Turn off internal Serial and Parallel port Turn off Network stack for boot Turn off wake-on-lan (for now) Set XHCI Handoff to enabled Don't enable decode over 4G Depending on your GPU, set priority for boot Set internal GPU (iGPU) to enable - not auto or disabled Set DMVT pre-alloc min to 64MB and max to 128MB. For this selection to appear you might need to reboot after setting iGPU to enable Set USB legacy to enabled Activate XMP profile 1 f your Ram has it (mine doesn't and I added the timings manually) Set ERP to enable, disable platform power management (I need to do more research if this could be enabled)  
      I've attached my current BIOS config "hack2". You can place that on a fat32 drive (the EFI partition of your install USB drive might be an idea) and see if it loads. It's made for and with the F2 BIOS.
       
      The install itself should be like other MacOS Hackintosh installs with it several reboots and ensuring to select the correct boot device in Clover.
       
      2. Post-install
       
      2.1 Install clover on target
      This is a no-brainer, but install a fresh copy of Clover on your target medium.
       
      During install select again AptioMemoryFix but also additionally
      EmuVariableUefi-64.efi Install RC scripts on target volume because otherwise NVRAM doesn't seem to work
       
      After the install, copy
      config.plist contents of "Other" content of "patched" to your new clover install.
       
      2.2 Edit ACPI for slumber
      Choose one option, not both. The hot-patch is experimental, but for the moment it is stable.
       
      2.2.1 Edit DSDT
      No more need for manual DSDT patching. If you still do it, you might run into unstable sleep. SSDT hot-patching + sane clover.config edits are enough
       
      This is necessary only once on initial install and every time, you edit or upgrade the BIOS. The DSDT.aml attached to this post might work for your system or give you a file to compare to. Don't expect it to work for you, though.
      EDIT: Since moving from F2 BIOS to F12 I did not repatch and sleep is still somewhat reliable. But to be 100% sure, you can still follow these steps.
      I won't go into the details of DSDT extraction and patching. There are better guides (the linked guide is a rip-off of rehabman's guide from a different forum). Please follow such a guide to extract your ACPI data.
       
      Locate and disassemble the DSDT with the newest iasl binary you can put your hands on, then open it with MacIASL in its newest version you can find (Hint: Here is a good source) You can check if the version is new enough if MacIASL doesn't throw error upon compiling a freshly extracted DSDT.aml or DSDT.dst
       
      Add rehabmans repo (as per linked guide) and apply the following patches:
      Rename _DSM to _XDSM Fix _WAK Arg0 v2 USB3 _PRW 0x6D Skylake (instant wake) Find the CNVW device and remove the _PWR function there.
       
      Compile the DSDT and place it in "patched".
       
      2.2.2 Use SSDT hot-patching
      Instead of having to re-extract and re-patch the DSDT on every BIOS change or update, Hardware change one can also use ACPI hot-patching.
      It's a combination of config.plist patches and an SSDT, which is hot-patched into the ACPI (if I understand the process correctly)
       
      You need to add this SSDT-GPRW.aml to your Clover folder in the designated position at Clover/ACPI/patched You need to add this patch to your config.plist. It goes into the DSDT patch section  
      Note: This works for me, but the patch removes the _PRW method from all devices in the DSDT. This could have side-effects. So far, I have seen none. At the moment I'm also not applying any other patch, compared with the additional edits I made to the DSDT method before.
       
      2.3 Install kexts to system
      As mentioned in the install section, it's better to follow rehabman's instruction and install USBinjectAll.kext to /L/E:
      sudo cp -R Release/USBInjectAll.kext /Library/Extensions sudo touch /System/Library/Extensions && sudo kextcache -u / 2.4 Enable onboard Audio - Install AppleALC kext
      Make sure your EFI partition is mounted and that you have a vanilla AppleHDA kext available. See below for a guide how to get a vanilla AppleHDA if needed
      Note: Our Audio codec is ALC887 and it's running with layout ID 1.
      Download the newest AppleALC kext from here and install it together with lilu.kext from here into your usual /clover/kexts/others location. Done. No scripts or config.plist patches necessary.
      Add layout ID 1 to config.plist, if it's not there yet:
      <key>Audio</key> <dict> <key>Inject</key> <integer>1</integer> <key>ResetHDA</key> <true/> </dict> If you previously  installed any  audio patches, please follow this guide to "vanilla-ize" your install.
       
      2.5 Optional steps for Graphics
      If you have a dGPU, now it's the time to install its drivers and adjust the config.plist for it. The detaisl are specific to your GPU and thus of scope of this guide. Yet, my supplied config.plist is ready to be used with Nvidia Pascal cards and using the Nvidia web driver.
      Whatevergreen.kext helps with Intel iGPU and NVIDIA dGPU fixes.
       
      At the moment I'm also testing out a special bootflag: 'shikigva=12' to enable faster rendering in Final Cut Pro X. Without whatevergreen.kext and a shikigva bootflag, rendering in final cut seem very slow.
       
      2.5.1 Framebuffers
      If you're facing problems with output from your internal GPU, you can try the framebuffer patches listed by @BackwardMac:
       
      2.6 Install a proper keyboard layout
      You might not be using a fancy Apple branded keyboard. If you use a PC keyboard, you might be annoyed by the differing layout and usage of keys. As a German, you might find yourself quitting applications, since alt gr + Q won't add an @, but quit your current application. To fix this, you can simply install a different keyboard layout. Copy it to /Library/Keyboard Layouts/ and chose the layout in System Preferences, Keyboard in the section "Other". Deleting the previously selecting layout makes sure that only this one is used. Nice little trick.
       
      A keyboard layout for German keyboards is attached and works wonders
       
      3. Updating
      Updating inside 10.3.x/ 10.4.x point updates doesn't require much attention:
      Download the update from the AppStore as any Mac would do Allow the system to reboot Before booting MacOS with Clover, make sure to disable extra drivers for dGPUs which require non-native support. If using an Nvidia dGPU: Remove "nvda_drv=1"  from your boot arguments and disable Nvidia injection If using a non natively supported AMD card, do the same for AMD (I'm not using AMD, thus I cannot be specific) Boot into the newly created Install MacOS partition Repeat this process until the Install partition is gone Boot MacOS again, still following 3., and potentially install updated drivers Your Audio might require re-patching  
      4. ToDo
      Move away from static DSDT patching to SSDT hotpatching --> requires my work Native NVRAM --> requires developer work Audio without AppleHDA patching --> requires developer work  
      5. Thanks to
      @MaLd0nfor helping finding the right way with the DSDT
      @RehabMan, for being a legend and helping me out patching
      @toleda, for audio patches for the 300 series
      /u/corpnewt, for his superb vanilla guide
      @wmchris for his super XPS 9550 guide and introducing me to hot-patching
      @Panzerschiffe for his addition to this guide
      all the developers of clover and it's awesomeness
       
      SSDT-UIAC.aml
       
       
       
      win-germany.keylayout
       
    • By Reel
      All work except camera
      You need SwitchResX that the screen does not freeze
         


    • By RougeOne
      Budget Workstation MacOS 10.14.1 build: z370 AORUS Gaming 5 - i5-8600K - RX 580 - UHD 630
      flawless iGPU/dGPU integration, fast FCPX editing/rendering, great overall performance for ~$1200 / ~£1000
       
      Update: updated WhateverGreen and Lilu, then updated OS to 10.14.3 and everything is fine! Even iMessage, which previously I hadn't been able to make work, is now working - possibly the update flushed the NVRAM?
       
      I'm gonna come straight out and admit it - I used newb tools which are considered taboo on InsanelyMac, and so this isn't so much an installation guide as it is a green flag to anyone considering the same hardware. My first and previous Hackintosh project was just over ten years ago and this site was massively helpful, so this is my (very small) way of giving back.
       
      EFI DIRECTORY
      http://s000.tinyupload.com/index.php?file_id=97606131925137056003
       
      HARDWARE
      CPU: Intel i5-8600K 3.6GHz hexacore (contains UHD 630 iGPU)
      CPU Cooler: be quiet! Pure Rock Slim (no paste needed, and fan facing front)
      Mobo: GIGABYTE z370 AORUS Gaming 5 (WIFI)
      RAM: 1x 8GB CORSAIR Vengeance LPX C16 2666MHz (in first slot)
      GFX Card: Sapphire RX 580 NITRO+ SE
      SATA: used ports 0, 1, 3, 5 (HDD problems when connected to port 4)
      HDD: generic
      DVD Drive: generic
      PSU: EVGA 500W Semi Modular (but you should get 650W!)
      Case: CoolerMaster CM590 III
      Fans: 2x stock case fans (one sucky on front, one blowy on back), 3x be quiet! BL046 120mm fans (two blowy on top, one sucky on front). Airflow near-perfectly balanced.
       
      ADVICE
      With the Clover configuration, you want to pay close attention to all things relating to graphics. There are some specific settings for ACPI, Boot, Devices and Graphics which should be copied exactly in order to get the iGPU and dGPU to work in perfect harmony. For instance, make sure you use ig-platform-id 59120003 rather than 59120000 if you want FCPX to be usable. With the right settings, FCPX will not only run, but run flawlessly.
       
      I was not able to figure out how to make NVRAM/PRAM behave itself, and I got errors when I tried to issue relevant commands. As a result, I could not at first get iMessage to work properly. It worked once on my first installation attempt but not from subsequent attempts. This Clover configuration therefore has no consideration whatsoever toward iMessage reliability - however, iMessage ended up working somehow, anyway - I noticed it after I'd updated to 10.14.3 but this may just have been coincidence.
       
      Onboard WiFi does not work. There is no driver for it. I'm using wired ethernet to a bridge router as it was cheaper than getting a compatible PCI card.
       
      Audio is working well after I installed the z370 audio patch, then the ALC1220 codecs, then AppleALC.
       
      With kexts for generic 3rd party SATA and generic 3rd party eSATA, my HDDs and DVD drive work perfectly well.
       
      Sleep/Wake functions run perfectly. iCloud functions run perfectly. Shutdown leaves the mobo LEDs on, annoyingly.
       
      My USB 3 ports seem to suffer from low power output, and I don't know why.
       
      Overall, this system appears to run about as well under MacOS 10.14 Mojave as it does under Windows 7. I would solidly recommend this build to anyone looking to build a computer for workstation purposes, on a budget.
    • By JhonneR
      Good morning, everyone, I'm sorry if I was wrong in choosing the topic but I need help.
      I have found it extremely difficult to mount a Hackintosh in my acer.
      Setup;
      I5 2430m 2.4 6GB RAM
      Mobo P5we0 - Intel intel Graphics 3000
      At the moment I have not found out what my audio codecs are.
      but I'll leave the link on the motherboard.
      however, my real problem is several.
      I have already used the itakos image, I have already used several images that could be installed normally and that after installing the image I do not have internet via cable or wireless.
      And another, I already looked in other forums and I know that I will be called a donkey in the logical question but I have not been able to install the [url=&quot;http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/&quot;]#####[/url] or clover to start from the Hard Disk, so I do not know what to do.At the moment I still do not know if there has already been someone who has already installed the High Sierra or just the Sierra in this notebook model and obtained permanent success.
      If anyone can help me, I'll be grateful.
      Installations without success, but with the system already installed in ACER;
      SIERRA
      HIGH SIERRA
      MOJAVE
      All with the same symptom. Starting only by the bootable USB stick and without internet connection via cable and wireless.
      Appreciate ! Acer 5750 Official Page
    • By Slice
      Since rev 4844 Vector Themes are supported and there are ready-to-use Clovy by Clovy, cesium by Slice and BGM_SVG by Blackosx.
      You may see it's structure to create own theme
      -------------------------------------------------------------------------------------------------------------------------------------------------------
       
       
      Now I want to add vector graphics support in Clover. See rev 4560 and later.
      It is not working yet but designers may begin to create Vector Themes.
      It supposed to consist of SVG elements and has design size. It will be rendered to any screen size scaled from design size.
       
      What application in macOS can create SVG graphics?
      Inkscape is not working in macOS 10.11+. Pity.
      LibreOffice Draw works with SVG but buggy.
      Boxy SVG cost 10$ but looks good enough. It creates the best in simplicity files and have more then enough features.
      Illustrator is good but expensive.
       
      How to improve SVG file?
      Clover has restricted support for SVG. It is your job to make compatible file and as small as possible to speedup rendering.
      Some helps:
      Help:Inkscape – From invalid to valid SVG Inkscape files
      From invalid to valid SVG Adobe Illustrator files
      From invalid to valid SVG files of other editors: BKchem, ChemDraw and CorelDRAW
      Help:Illustrator – Assistance with creating and saving SVG images in Adobe Illustrator that will pass W3C validation
      User:Quibik/Cleaning up SVG files manually
      Later I will write own instructions specific to Clover abilities.
       
      How to create SVG fonts?
      You can google to find ready-to-use SVG fonts.  I found some problems with too beaty fonts: slow rendering and overflow crash. Be careful.
      You can get ttf or otf fonts and convert them into svg by using online WEB services. Not a problem to google.
      But then I want to find a way to simplify the font to reduce a size and speedup rendering.
      You can create own font by FontForge It is opensource and available for Windows, Mac and GNU+Linux. It creates otf font which you can convert to svg font.
       
      Pictures from Badruzeus
      https://www.insanelymac.com/forum/applications/core/interface/file/attachment.php?id=301597
×