Jump to content
fantomas

[Tuto] QE_CI Exotic Patch via Clover

86 posts in this topic

Recommended Posts

Salut,

 

La DSDT patchée peut être utile même avec les patchs clover.

J'ai un cas sur mon optiplex 745, la compile à la volée se passe mal et donc kernel panic.

Ce qu'il faut vérifier pour être certain que ton problème ne vienne pas de la, c'est extraire ta DSDT sous linux et essayer de compiler.

Si tout se passe sans erreur le patch Clover suffit, sinon il faut que tu corriges la DSDT pour que cela compile sans erreur.

Puis appliquer les patch Clover.

 

 

Fred

Share this post


Link to post
Share on other sites
Advertisement

Oh le mauvais... c'est pas une 4850 mais un 4890... oh le mega mauvais !!


Voila ou j'en suis suite à un post que je viens de lire
 

Fakeid: 0x94401002

+Fixdisplay

+ KernelAndKextPatches : x2000 FF83F91A -> FF83F93A / 0F838A010000 -> 909090909090

Avec ca j'ai bonne réso, acceleration matérielle :) 

sans Inject ATI j'ai le dual screen :)

C'est tout bon :)

Share this post


Link to post
Share on other sites

J'admets ... ce matin je sors la carte pour tester avec un GT610 à la place et la je vois... 4890...


Bon apres j'hésite quand meme avec la 610 qui est fan less ! C'est un peu une turbine la 4890

Share this post


Link to post
Share on other sites

Je mets ce topic à jour pour la sortie de macOS 10.13 Beta

 

J'utilise actuellement la version r4084 de Clover.

 

Alors pour le patch, vous devez comme d'habitude, ajouter votre Device-id dans AMD4800Controller.kext et ATIRadeonX2000.kext et pour la partie "binaire" du patch du ATIRadeonX2000.kext, il faut se rendre à l'offset 0x68d6e et éditer 6 bytes (0F 83 1B 01 00 00) par l'instruction NOP (90 90 90 90 90 90).

 

La particularité cette fois-ci est que ces 6 bytes se trouvent à 2 endroits (le second est à l'offset 0xA2BB5, il ne nous est util), donc pour que notre patch ne soit pris en compte QUE par le premier, on va lui ajouter d'autres bytes (5 bytes pour être exacte) pour qu'il soit différent du second, comme ceci :

 

01 48 0F A3 C1 0F 83 1B 01 00 00  -->  01 48 0F A3 C1 90 90 90 90 90 90

 

 

Une autre particularité est que, dans mon cas (je ne suis pas sûr que cela s'applique à tout le monde), j'ai toujours utilisé Clover Configurator afin d'ajouter des patchs dans mon config.plist et je n'ai jamais eu de problème(s) lié(s) ) à la casse (case sensitive)... jusqu'à présent. Et comme CC utilise que des minuscules, Clover ne pouvait pas patcher mes kexts à la volé. Et c'est juste lié aux patches d'Info.plist (pas de problème pour le patch de la partie binaire du kext).

 

J'ai dû donc utiliser mon p'tit logiciel Base64 Encoder Decoder pour avoir la bonne conversion de mon Device-id.

 

Voici ce que ça donne au finale :

<key>Graphics</key>
	<dict>
		<key>FBName</key>
		<string>Cardinal</string>
		<key>Inject</key>
		<dict>
			<key>ATI</key>
			<true/>
		</dict>
	</dict>
	<key>KernelAndKextPatches</key>
	<dict>
		<key>AppleRTC</key>
		<false/>
		<key>Debug</key>
		<false/>
		<key>KextsToPatch</key>
		<array>
			<dict>
				<key>Comment</key>
				<string>Exotic patch</string>
				<key>Disabled</key>
				<false/>
				<key>Find</key>
				<data>OTQ0YTEwMDI=</data>
				<key>InfoPlistPatch</key>
				<true/>
				<key>Name</key>
				<string>AMD4800Controller</string>
				<key>Replace</key>
				<data>OTQ0YzEwMDI=</data>
			</dict>
			<dict>
				<key>Comment</key>
				<string>Exotic patch</string>
				<key>Disabled</key>
				<false/>
				<key>Find</key>
				<data>OTQ0QTEwMDI=</data>
				<key>InfoPlistPatch</key>
				<true/>
				<key>Name</key>
				<string>ATIRadeonX2000</string>
				<key>Replace</key>
				<data>OTQ0QzEwMDI=</data>
			</dict>
			<dict>
				<key>Comment</key>
				<string>Exotic binary patch</string>
				<key>Disabled</key>
				<false/>
				<key>Find</key>
				<data>AUgPo8EPgxsBAAA=</data>
				<key>Name</key>
				<string>ATIRadeonX2000</string>
				<key>Replace</key>
				<data>AUgPo8GQkJCQkJA=</data>
			</dict>
		</array>
	</dict>

Avec CC

 

8701851013Exoticpatch.png

 

 

Avec Info.plist Editor (Xcode)

 

5180101013Exoticpatch.png

Share this post


Link to post
Share on other sites

Bonsoir!

Je viens de comparer le fichier ATIRadeonX2000 original avec ta patch.

Dans ce post tu n'as pas parlé de ça:

 

"Replace 1 byte at offset 0x68d59 with 1 byte"

 
Il faut donc changer 3E avec 3A?
Merci!

 

post-327171-0-12941100-1512857223_thumb.png

Share this post


Link to post
Share on other sites

Il faut donc changer 3E avec 3A?

 

Salut sughero  ^_^

 

Oui, c'est juste un oubli de ma part. En faite, le patch que tu évoques ne concerne  que certaines HD4890 qui en ont besoin en plus du patch normal, c'est tout.

Share this post


Link to post
Share on other sites

Bonjour, 


Je parcours avec attention ce fil ces derniers jours, et je me demandais s'il était possible de patcher de la même façon ATIRadeonX2000 pour les cartes présentes dans AMD4600Controller. Je prévois en effet d'installer El Capitan sur un petit laptop équipé d'une HD 4330 M (0x95521002).


J'ai quelques questions:


  • Comment la valeur 0F838A010000 a-t-elle été déterminée? Dépend-elle du Device ID? Sera-t-elle la même dans mon cas?
  • Le kext ATIRadeonX2000 est-il un kext présent "naturellement" dans El Capitan? J'ai un Mac sous Sierra et un hackintosh sous High Sierra et cette extension n'est pas présente dans S/L/E. Faut-il l'installer dans ce répertoire ou la mettre avec les autres dans le répertoire 
/kexts/Other de Clover?
  • À certains endroits vous parlez de changer de Framebuffer. Cela se passe dans le config.plist comme dans le post #82?

Si ce n'est pas possible, tant pis, j'installerai Linux! En m'excusant de vous faire perdre votre temps.
 
Je joins mon config.plist envisagé. config_5810T copie.plist.zip

Share this post


Link to post
Share on other sites

Je mets ce topic à jour pour la sortie (encore en bêta version) de macOS Mojave. En faite, Apple a décidé, dans la dernière version majeur de son système d'exploitation favori, de supprimer (partiellement du moins) le support pour tous les Macs qui ont des GPU non-Metal (la nouvelle API propriétaire d'Apple) et de ce fait, de nombreuses cartes graphiques inférieurs aux HD7xxx ne fonctionnent pas, tout simplement parce qu'Apple a retiré les kexts.

 

Après de nombreux retours (sur le site de MacRumors), j'ai décidé de me lancer et ça s'était avéré payant. En réalité, vous aurez juste besoin des kexts de High Sierra et vous pouvez appliquer les mêmes méthodes que j'avais déjà mis en place, çàd patch à la volé (dans mon cas ci-dessous) ou l'ajout du Device-ID manuellement (j'avoue que je n'avais pas encore essayé cette méthode mais je ne vois pas pourquoi elle ne fonctionnerait pas).

 

Capture d’écran 2018-07-13 à 03.45.57.png

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By Simon's InsaneMac
      Hi, I'm kind of lost when scrolling to Clover Configurator, so I decided to use an EFI from the web and just configure the most basic stuff. But that sadly didn't work, im always getting the attached screen IMG_0054.HEIC (and I don't know whether all the errors are listed, as I can't scroll). 
      Anyways I thought it'd be better to do a custom setup. Can anyone give me some help with what to choose in the settings? Here's my rig:
      i7 8700k
      Asus z370-G (Rog Strix)
      gtx 1060 6gb
      samsung ssd (SATA)
      WD hard drive
       
      Your help would be much appreciated!
    • By kylon
      A big thanks to wegface for teaching me a lot of things.
       
       
      Tested on Catalina 10.15.4 and Clover EFI 5104 (Catalina Patcher)
       
      Not Working:
      - realtek sd card reader (pm me if you have a fix)
       
      Notes:
      **CPU patches are disabled, if you are using a locked BIOS you must enable them**
       
      Clover EFI:
      - Install it in UEFI Mode and change your hdd partition table to GPT.
      - You will be able to install ANY OS in EFI mode, even if this pc does not support EFI at all! (No guide available for this)
       
      You will need:
      My unlocked BIOS (OPTIONAL) (here) Latest Clover config from CCE Bank (here) (asus k53sj-kylon) Rehabman Voodoo PS2 Controller (here) acidanthera AppleALC (here) acidanthera Lilu (here) acidanthera VirtualSMC (here) acidanthera SMCBatteryManager (here) acidanthera SMCLightSensor (here) acidanthera WhateverGreen (here) Mieze Realtek RTL8111 (here)
    • By y010204025
      Disclaimer: All files of this article are from itpwd.com and rehabman ’s github.com

       
      After Testing:
       
      Graphics card: NVIDIA K1000M / K2000M / K2100M / K3000M / K3100M / K4000M / M1000M (ordinary TN1600x900 or 1920x1080), AMD W5170M / W7170M (DC2 or 4K), Intel HD4000 (ordinary TN1600x900 or 1920x1080) can be driven normally, but NVIDIA graphics card Brightness adjustment is disabled. AMD W5170m and w7170m are the best choices on 8570W and 8770W. The brightness can be adjusted normally and the graphics performance is very good. For WX7100m and WX4170m, the graphics card fans cannot be controlled, and other methods are required to control the fans. CPU: 3rd generation Intel Core i3, i5 and i7 (Ivy Bridge architecture, including all dual-core and quad-core. Celeron and Pentium are not supported), frequency conversion is normal. In general: If you have 8570W, 8770W, and hope you can get the best Hackintosh experience, it is recommended to replace the CPU with i7-3840QM / i7-3940XM, 8570W is recommended to choose W5170M, 8770W, and it is recommended to choose W7170M. In addition: If you want to have a 4K experience or perfect HIDPI, W5170m / W7170M supports 4K output, you can choose a suitable 4K screen to replace, but because 4K screens are mostly edp interface, and 8570W / 8770W motherboard is lvds interface, This requires a custom screen cable, which seems to be a difficult choice, but you can choose to do it yourself or buy it separately. In China, taobao.com is almighty and may be more suitable for you than eBay.
       
      EFI features:
      out of the box, the relevant hardware can be driven after the OS is installed, and it is easy to use without code operation.
      Supported models: HP EliteBook 8470p, 8570p, 8570w, 8770w (click the model for official specifications)
      Wireless network card: Recommended: BCM94360cd (requires ipex4 to ipex1,3 antenna 1300mbps), BCM94352HMB / DW1550 (2 antennas, 867mbps)
      Wireless characteristics: no white list, wireless network card with Bluetooth does not support the Bluetooth function of the wireless network card (also does not need to shield the pins), but the wireless normal use, you need the Bluetooth function to use this machine comes with Bluetooth:
      Clover version: 5103, keyboard mapping has been added Command key = Alt key, Option key = Win key
      Supported systems: macOS Mojave 10.14.6 (18G103)-macOS Catalina 10.15.x,
       
      Notes on known issues:
      1. The touchpad and the left and right keys under the touchpad are normal, the pointing stick and the left and right keys above the touchpad are temporarily unavailable (recommended to use the second generation of Apple Magic Trackpad)
      2. Indicator display problem (can be ignored, function is normal): Caps light is sometimes not switched in time, mute / wireless key may be yellow
      3.AMD graphics card / Intel nuclear display has supported sleep and 15 levels of brightness adjustment, NVIDIA has no
      4. If the AMD graphics card enters Huaping, refer to editing the Clover startup parameters, and add the Boot parameter radpg = 15 (the EFI file that has been configured with this parameter has been uploaded, refer to the following EFI-guided download link)
      5. Using the above NVIDIA graphics card with a normal TN screen 1600x900 or 1920x1080 can not enter the installation interface, please check whether the VBiOS of the graphics card is exclusively for HP, thank you for your test face K1000M
      6. Due to product design defects, the MSata positions of 8570w and 8770w cannot be used as boot disks, so EFI boot can only be placed on the main hard disk (turn the machine over and open the hard disk in the lower left corner of the cover, which is the main hard disk). Put on msata plate
      +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
      Hardware requirements:
      Model: 8470p, 8570p, 8570W, 8770W 1 or more, it is recommended to use another notebook for emergency Hard disk: It is recommended to choose an SSD hard disk of 240g or more. Samsung or Intel SATA hard disk is a good choice. Wireless card: BCM94352HMB, DW1550, BCM94360CD, miniPCIe slot U disk: 1 for 16g and above, another winPE emergency USB disk is recommended If you use a rescue USB flash drive, it means that you read this post carefully
       
      Make and install a USB flash drive:
      Get the mirror: please do it your way Making and installing a USB flash drive: macOS command line production is recommended, whether it is a real macOS model or a virtual machine (although this is not allowed to be discussed in many forums)Or you can choose to use TransMac or ether under Windows. This is not recommended, but it is simple enough for those new to Hackintosh. Make boot U disk: If you know how to put the boot into the installation U disk, unzip the EFI file and put it in the EFI partition, or you can choose a fat32 format U disk to store the EFI file separately Note: EFI is an unzipped folder, not a zip or ISO suffix file.
       
      BIOS settings From RehabMan
      To start, set BIOS to defaults.
      Then insure:
      UEFI boot is enabled (hybrid/with CSM for best result) secure boot is disabled disable fast boot IGPU graphics memory set to 64mb, if available disable the serial port via BIOS option, if available disable "LAN/WLAN switching", if available disable "Extended Idle Power States" if you find it under "Power Management Options" disable "Wake on LAN" and "Wake on USB" disable Firewire/IEEE 1394, if your laptop has it for Skylake and KabyLake laptop, enable "Launch Hotkeys without Fn keypress" Note: If you have a laptop with switchable graphics, leave it enabled. You can still use it on Windows, although the discrete card will be disabled when running OS X by the ACPI patches provided here. If you want to also disable it in Windows (via BIOS option), make sure you read about the DGPU option in your model specific SSDT (source is in SSDT-HACK.dsl), as in the scenario where the DGPU is disabled by BIOS, DGPU should be set to zero.
       
      Install:
      Please modify according to the above BIOS settings: Press F9 after booting, select the boot efi to file option, which is generally the last item. Enter your boot USB disk to find the location of cloverx64.efi, select cloverx64.efi, press Enter, and enter the clover boot interface. Select the location of the install entry and press Enter. Enter the macOS interface, use the disk tool to format the partition you need to install to hfs + or apfs format, do not choose the encryption option, this will make your efforts in vain. Note: The disk must be in gpt format, and the remaining EFI space is greater than 200M, 300mb + is recommended. If it is not, please try to modify it in WindowsPE environment. This may cause you to lose the Windows system boot and disk data. Please prepare for backup.
      After formatting the partition successfully, close the disk tool and select install, you will find the partition you installed, and follow the interface prompts. When the installation reaches a certain progress, it will restart. When restarting, select F9, enter from the boot U disk, select the disk partition where you installed macOS (no longer the U disk installation), the installation will continue, and it may restart 2 ~ 3 times Every time, you need F9 to select the boot. After entering the installation interface, except for the first installation, select the U disk, and then select the disk installation partition. Eventually you will enter the settings interface. After following the interface prompts, you will enter the macOS system interface. Remember the system password and turn off the Find my mac option.  
      Post install:
       
      After the installation is complete, you need to hang the EFI partition of the disk, copy the EFI file of the U disk to the EFI partition of the disk, so that you can directly use the disk to boot, otherwise you need to select the U disk to boot each time. The mount tool can choose cloverconfigurator. If after copying the EFI file to the disk, the computer cannot recognize your clover boot, you can use the custom boot option of bios: set the custom boot path to \efi\clover\cloverx64.efi, and set it as the first boot, Use bootice or easyUEFI to increase the clover boot option under Windows and set it as the first boot. If you do not have a wireless network card available temporarily, you can use the USB binding function of your Android phone to share the network. This may require the HoRndis driver. It is not recommended to use a US wireless network card. If you need Windows or Linux, you can install it normally. Be careful not to let Windows overwrite your boot files.  
      For other uses of macOS and brew, please pay attention to forums and other communities. Hackintosh is just the beginning.
       
      Finally, I would like to thank rehabman, vit9696 and others who contributed to Hackintosh. I also thank Cwen for his efforts to modify files and hardware tests. I hope that Hackintosh will be eternal.
       
      Please comply with the laws and regulations of your country or region. My description may not be clear or professional, but I think it is necessary. I think the existence of Hackintosh is everyone's technical hobby and experience macOS, not as a substitute for macOS cheap hardware.

      EFI_8x70_5103_W7170m_20200116 .zip
    • By StarFighter_77
      I built this hack years ago now. Started with Lion, now on El Cap. I want to update now to High Sierra.

      I think I messed up my Clover when I downloaded the update .pkg and just installed it without taking my time or customizing the install. Was on Clover r3423, now I think I'm on r5104

      I've been searching and reading this site and others for a few days before making this thread, but I need help compiling what I've learned to get my system running correctly again and ready to update to High Sierra. Then, eventually, I want to update my graphics card, switch to UEFI (if necessary) and update to Mojave.

      I couldn't get system to boot. Could get to Clover and all the options, except the Shell... I hit enter on the Shell and I get black screen and nothing.

      The only way I got it to boot was to add -v to boot args, and change smbios from 14,2 to 13,2. Not sure why that worked still. Also I'm running two monitors, but I can only now run one of them off the Intel 3000 Graphics and the second one off my GFX Card.

      So now I'm afraid to shut down or reboot.... I could really use some help with Clover.

      I'm pretty sure my config file in Clover is not right. Also, some of the files in my Clover backups are not in the new Clover install. (2.5k 5104)

      If someone could please take a look at the files I've attached and help me sort this out, I would be grateful. Thank you, Thank you, Thank you.

      I've attached
      - The last boot log
      - The current Clover folder from the EFI partition after performing Clover update. (.zip)
      - The Clover backup that was working before Clover update (.zip)
      - Library/Extensions Folder (screen shot)
      - System/Library/Extensions Folder (.zip)

      Here is my current hardware:

      Mobo: GIGABYTE GA-Z68MX-UD2H-B3

      CPU: Intel Core i7-2600K

      GPU: GIGABYTE ATI Radeon HD6870 1GB DDR5 2DVI/HDMI/2x

      RAM: Corsair Vengeance Blue 16 GB DDR3 SDRAM Dual Channel Memory Kit CMZ16GX3M4A1600?C9B

      HD0 (for OS and Apps): OCZ Technology 120 GB Vertex Series SATA II Solid State Drive

      HD1 (file storage, Adobe scratch disk): Samsung 1 TB Spinpoint 7200 RPM 32MB Cache SATA

      BURNER: LG CD/DVD Burner Model GH22NS50

      CPU COOLER: Corsair Cooling Hydro Series H50 All in One High-performanc?e CPU Cooler CWCH50-1

      P/S: Antec CP-850 850 Watt CPX Power Supply Unit

      CASE: Antec Performance One P183 V3 Case
      CLOVER.zip
      CloverBackup.zip
      bootlog.txt

      S_L_E.zip
    • By rodrinico19
      Hola a todos, primero que nada estoy muy contento de a ver econtrado un foro de español sobre hackintosh.
      Mi problema consesite en que descargue unos drivers de esta pagina: https://github.com/chris1111/Wireless-USB-Adapter-Clover
      Seguí los pasos instale los kets en la carpeta EFI/CLOVER/OTHERS todo tal cual como dice ahi la instalación. luego segui los pasos de configurar la red dentro de configuracion del sistema etc.
      Lo cual el nombre me quedo en en0.
      El driver o kets funciona bien es reconocible por el S.O de hecho conecta la red, pero me dice que no tiene IP AUTO ASIGNADA Y LA OTRA QUE HAY UNA DESCONEXION A CADA RATO(como que desconectaras y conectaras el dispositvo usb a cada rato)
      Me gustaria que me ayuden con eso si es posible, Muchas Gracias!!
×