Jump to content
Steiak

[Dúvida] Instalação via USB no PC

55 posts in this topic

Recommended Posts

Incrível, na ultima versão do AIDA essa opção não está aparecendo, ou está em algum lugar muito escondido, pois abri opção por opção.

 

Pelo DSDT Patcher eu posso fazer o mesmo procedimento diretamente no Mac?

Share this post


Link to post
Share on other sites
Advertisement

Mesmo clicando na barra abaixo no Aida com o botão direito, não aparece essas opções?

 

DSDT Patcher, já está desatualizado, ninguem usa mais ele.

 

Tenta no DSDT editor:

Screen Shot 2014-03-20 at 3.05.28 PM.png

Share this post


Link to post
Share on other sites

Aparecem várias opções, mas não a que precisamos, vou tentar, mas agora só a noite, obrigado pela força e até mais!

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By TimothyF
      My steps so far:
      Set up Catalina install USB exactly according to Plain Vanilla guide. Disconnect my Windows drive in PC, so that only the empty Hard Drive is connected to Motherboard. Boot to USB, select Install Catalina option. BIOS set to UEFI, Safe mode Off. Always get stuck at the same IOconsoleUsers: GIOScreenLockState point. Tried -radvesa, -radoff, nv-disable=0 boot options (separately), and disabling BIOS virtualization (vt-d) -> NO luck. This from the top search result https://www.reddit.com/r/hackintosh/comments/b5a6ry/ioconsoleusersgioscreenlockstate_3_blackscreen/  
      Screen pics attached. Here are the last couple of lines that could be important:
      GTrace synchronization point 4
      Unsupported CPU
      Unsupported PCH
      Adding ADGP mode validate property
      hmm.. mismatch sizes 3100 vs 20
      IOConsoleUsers: time(0) 0->0, lin 0, llk 1,
      IOconsoleUsers: gIOScreenLockState 3, hs 0, bs 0, now 0, sm 0x0
       
      Please give me some ideas what else might work. Thank you.


       
       
      Other details of Clover and Desktop PC below:
       
      Clover USB specs OS installer used: Catalina (10.15) Clover revision: 5103 Kexts included: ATH9KFixup.kext AppleALC.kext Lilu.kext RealtekRTL8111.kext USBInjectAll.kext VirtualSMC.kext WhateverGreen.kext config.plist: config.plist ------------------------------------------ Target Desktop specs: Dell Inspiron 3847 (64 bit) CPU: Intel Core i5-4460, 3.2 GHz, 4 cores Architecture: Haswell GPU: Intel HD 4600 Motherboard: Dell 088DT1 (version A01) Chipset: Intel H81 Install method: with USB, configured with Clover, 100% following Plain Vanilla guide for Desktops RAM: 12 GB, 2 slots Hard drive for installation: SATA HDD 4TB, by HGST LAN: RTL8111/8168/8411 WLAN: AR9565 (atheros) Audio: Realtek ALC661 (not 100% sure this is correct)  
    • By Vyzantion
      I have just re-made the Catalina installer, with the updated OS. It could not install from it, like it could not copy. Then I have tried to reinstall Mojave, it worked pretty cleary last year the exact pen drive. It failed as well, saying something like: not package found, contact the system administrator. I was able to boot from USB pen drive Linux and install Windows from DVD. But no macOS from the pen drive, even from what worked fine before. I have reseted the BIOS several times, no succes. The first sign of something wrong was this: When I first tried to boot Catalina, it said something about BIOS (BIOS, not UEFI) reset and enter setup. I hapenned several times on my attempts. If something screwed in my hardware? The USB ports? The BIOS perhaps?
    • By rich_mark
      My Mac recovery mode is not working and I haven't found the valid solutions on internet. 
      How to boot Mac into recovery mode and recover the files?
      Thanks in advance!
    • By Justin S
      I purchased two of these Sipolar 10 port USB 3.0 hubs with the thought I'd be able to plug in 20 iPads to do software restores simultaneously, but I only can get 12 to be recognized at any one time. Both hubs function properly with 10 iPads plugged in to each at once, but as soon as I connect both hubs I get a max of 12 iPads recognized by the OS. We're using Apple Configurator 2 to restore iPads, and I have a separate older/slower 32 port USB 2.0 charge/sync hub that works fine with all devices plugged in.
       
      Hub: https://www.alibaba.com/product-detail/Sipolar-new-a-423-10-port_62315150518.html?spm=a2700.icbuShop.41413.40.5aa8663dB1drT6
       
      I'm using a 2014 Mac Mini 7,1 running 10.15.3. I've tested the hubs with a few difference Macs and OS's and have had the same issue. From what I can tell these hubs use a RealTek USB chipset, but no drivers are offered by Realtek for them.
       
      I attempted to daisy chain them (not ideal) and still have the same issue. Has anybody run in to a similar issue using identical USB hubs connected to individual ports on a Mac?
×