Jump to content
Slice

[HOW TO] Make Radeon {Desktop or Mobility} be working by using Clover

427 posts in this topic

Recommended Posts

From mine picture you can see you missed some amd files loading.... Even if you have screens black you MUST have amd kexts loaded! And then....patching connectors!

Well,i don't have black screens,only white,without spinning wheel,whenever the 6000controller loads...

Can you check this new boot.log ?

 

 

bootlog.log.txt

Share this post


Link to post
Share on other sites
Advertisement

OK so now I think it might actually be working, because...

When I boot to Mavericks installer on a known working computer (with NVidia GT240 works OOB),

the installer also has tearing and glitchiness! But when installed, it works superb.

 

So to recap, on my 8560w, when booting to Mavericks installer:

- The graphics card is listed with the correct info and correct VRAM

- It has much more smoothness / less glitches than if I would load it without injecting

- But there is still some tearing

 

Is this basically good to go?

 

EDIT: WOW, IT WORKS! ABSOLUTELY AMAZING!

Share this post


Link to post
Share on other sites

White/black/purple does not metter, you have to patch your connectors! Do it! It's time consuming so go!

But, patching connectors is useless if you have not amd kexts loaded! So again, put ioregexplorer on desktop, restart, once you are on desktop hit I (be sure you have only this file starting with I on desktop ) hut command + O to open it, hit command+ S to save a file, hit Enter to save it, then reboot without amd kext! Thus way yiu can know if all kexts are loaded....

And patch your connectors! You haven't Apple hardware so you have to do some work to getting it working!

Share this post


Link to post
Share on other sites

White/black/purple does not metter, you have to patch your connectors! Do it! It's time consuming so go!

But, patching connectors is useless if you have not amd kexts loaded! So again, put ioregexplorer on desktop, restart, once you are on desktop hit I (be sure you have only this file starting with I on desktop ) hut command + O to open it, hit command+ S to save a file, hit Enter to save it, then reboot without amd kext! Thus way yiu can know if all kexts are loaded....

And patch your connectors! You haven't Apple hardware so you have to do some work to getting it working!

That iOReg trick dsnt work for me,when i reach the white screen,can't do nothing but restart...

 

PS:Thanks for your effort anyway. ;)

Share this post


Link to post
Share on other sites

That iOReg trick dsnt work for me,when i reach the white screen,can't do nothing but restart...

 

PS:Thanks for your effort anyway. ;)

I know! Start to patching connectors k follow some guides!

Share this post


Link to post
Share on other sites

I guess i need first, find whats the correct configs in Clover as well as my DSDT GPU injection..

Correct config is mandatory!

You can try deleting all signs of your GPU from DSDT and in config.plist under Graphics put ATI = Yes, read Ckover manual first!

Share this post


Link to post
Share on other sites

Correct config is mandatory!

You can try deleting all signs of your GPU from DSDT and in config.plist under Graphics put ATI = Yes, read Ckover manual first!

Yeah,i Will try that.

Share this post


Link to post
Share on other sites

hello i have an ati mobility hd3470 with dev id 95c4 what frame buffer i need to use? i'm on mavericks 10.9, thank you for the answer

Share this post


Link to post
Share on other sites

hello i have an ati mobility hd3470 with dev id 95c4 what frame buffer i need to use? i'm on mavericks 10.9, thank you for the answer

See first post

As I see RadeonHD3xxx was successful only in 10.5

Share this post


Link to post
Share on other sites

After updating to OS X 10.10.4, der is some graphics glitches while startup :(

some multi colored dots appears at the center of screen, while it switches from black screen to desktop screen !

Share this post


Link to post
Share on other sites

Revert 10.9.5 will be the best solution.


As i saw some people had success even in Lion not only in 10.5 alias leopard

Ask them.

Share this post


Link to post
Share on other sites

hi please help my graphics ,, AMD 7610M ( HD 7500/7600 ), 6742_1002

only 4Mb graphics ,,

 

Toshiba/Quanta BY3/BY4 Thames LE DDR3                                       
 
Subsystem Vendor ID: 1002
       Subsystem ID: 1002
Object Header Structure Size: 199
Connector Object Table Offset: 34
Router Object Table Offset: 0
Encoder Object Table Offset: 99
Display Path Table Offset: 12
Connector Object Id [14] which is [LVDS]
encoder obj id [0x1e] which is [iNTERNAL_UNIPHY (osx txmit 0x10 [duallink 0x0] enc 0x0)] linkb: false
Connector Object Id [12] which is [HDMI_TYPE_A]
encoder obj id [0x20] which is [iNTERNAL_UNIPHY1 (osx txmit 0x11 [duallink 0x1] enc 0x2)] linkb: false
Connector Object Id [5] which is [VGA]
encoder obj id [0x15] which is [iNTERNAL_KLDSCP_DAC1 (osx txmit 0x00 enc 0x10?)] linkb: false
 
 
ATOM BIOS Rom: 
SubsystemVendorID: 0x1002 SubsystemID: 0x1002
IOBaseAddress: 0x4000
Filename: BR41926.007 
BIOS Bootup Message: 
Toshiba/Quanta BY3/BY4 Thames LE DDR3                                       
 
PCI ID: 1002:6742
Connector at index 0
Type [@offset 44700]: LVDS (7)
Encoder [@offset 44704]: INTERNAL_UNIPHY (0x1e)
i2cid [@offset 44774]: 0x91, OSX senseid: 0x2
Connector at index 1
Type [@offset 44710]: HDMI-A (11)
Encoder [@offset 44714]: INTERNAL_UNIPHY1 (0x20)
i2cid [@offset 44797]: 0x90, OSX senseid: 0x1
Connector at index 2
Type [@offset 44720]: VGA (1)
Encoder [@offset 44724]: INTERNAL_KLDSCP_DAC1 (0x15)
i2cid [@offset 44824]: 0x92, OSX senseid: 0x3

Share this post


Link to post
Share on other sites

I am having an issue with my 10.11.2 installation.  I am using two Radeon 7950's which are supposed to be natively compatible with OS X and they worked that way with 10.10 perfectly fine.  Ever since updating to 10.11 I am getting an error "**GPU hardware VM is enabled".  I get this error twice because I have two cards and when I remove one I only get one and when I remove them both it boots up fine but only with iGPU.  I am using Clover and if I use the graphics injector to inject some fake Device ID then it allows me to boot with just iGPU.  I did double check and my device ID is in the AMD7000Controller.kext "679A1002"  I think I have narrowed it down to the AMDRadeonX4000.kext because when I delete that it loads just fine (iGPU is normal, 7950's load but with no acceleration).  My device ID is also in that kext, however I did notice that in the X4000 kext my device ID is under Tahiti which isn't one of the listed controllers in my 7000Controller.  Any ideas why this might be happening?  Thank you for your time and I hope to hear back from you shortly!

 

MY motherboard is a Asus P8Z77-V

Share this post


Link to post
Share on other sites

i succeed to install el capitan on my pc everything work great except my graphic card ( ati radeon hd 4650) i fixed vram now it 1024mb but i can't get QE-Ci IT work my pc restart if i checked inject ati 

 

567d8e652f8f5_ScreenShot2015-12-25at8.35post-325332-0-53600000-1451003579_thumb.

Share this post


Link to post
Share on other sites

You have two problems:

1. CloverConfigurator

2. [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url].

Share this post


Link to post
Share on other sites

You have two problems:

1. CloverConfigurator

2. #####.

What wrong with Clover Configurator ? AFAIK that's the best way to get a hang of Clover before going the geek way. About that Beast thing, I have no objection, full of {censored}

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By Shaneee
      Here we have the AMD Vanilla guide. Compatible from Windows. 
       
      Click here for the guide.
       
      For installation help make a post here. And for post installation help make a post here.
       
      Thanks,
      Shaneee

    • By CMMChris
      I did it again! With the release of the Navi drivers for macOS by Apple I bought a card and ported my popular PowerPlay Table generators to the RX 5700 and RX 5700 XT. Some might know I already did the same for V56/64 and Radeon VII. This tool allows you to change GPU, SoC and Memory Clocks, voltages for GPU and SoC (for undervolting or overvolting), adjust Power and TDC limits and customizing fan control. The whole thing is based in a simple Excel spreadsheet and provides you with a long Hex string you can then inject to your graphics card via Clover device properties. If you want to use it on a real Mac (eGPU or Mac Pro) you can use a Dummy Kext to inject the PowerPlay Table. Please make sure that you only run this spreadsheet in Excel! iWork, OpenOffice and Libre Office are known to do wrong calculations.

       
      Release: AMD Radeon RX 5700 (XT) PowerPlay Table Generator V1.0
      (October 27 2019)
      Changelog 1.0:
      Initial Release  
      RX 5700 Download: Radeon_RX_5700_PowerPlayTable_Generator.xlsx.zip
      RX 5700 XT Download: Radeon_RX_5700_XT_PowerPlayTable_Generator.xlsx.zip
       
      WARNING: Use this this tool at your own risk! I am not responsible for your mistakes. Wrong / too high values can potentially damage or destroy your card.
       
    • By Arman Hossain
      HI 
      I want install High Sierra  on my pc . my CPU is : AMD Ryzen 3 2200g and my MotherBoard is : ASUS EX A320m. and 8gb ram DDR4 ram . i dont have any external gripch card. i have seen some video on youtube how to install High Sierra but they use extranal gripch card to make it good  but i don't have any extranal gripch card . on my windows sysem the shared gpu is 2GB which is using my ram to crate the vega gripch  . i want know is it possible to install High Sierra on my pc with out any extarnal gripsh card  ?


    • By MatthewBayard
      Current Build ( just purchased the RX 580 )
       
      CPU Intel Core i7-3770K 3.5GHz Quad-Core Processor       CPU Cooler Corsair H100i 77.0 CFM Liquid CPU Cooler     Motherboard Gigabyte GA-Z87X-UD7 TH       Memory 4x 8gb     (Corsair CML16GX3M2A1600C10 Vengeance Low Profile   16GB (2x8GB) DDR3 1600 Mhz CL10 XMP Performance Desktop Memory Kit Black)       Case Fractal Design   Define R4 (Black Pearl)       Power Supply Corsair HX750       HDD SATA 6Gb / s 256GB SSD         Wifi TP-LINK TL-WDN4800 N900 Wireless PCI Express Adapter       Graphics Card MSI RADEON RX 580 ARMOR MK2 8G OC Graphic Card      
       
      The installation has failed a dozen times after creating a bootable USB via the instructions outlined at serval different places:
      https://www.tonymacx86.com/threads/[url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url]-install-macos-mojave-on-any-supported-intel-based-pc.259381/   
      https://hackintosher.com/forums/thread/mojave-flummoxed-with-ga-z97x-ud7.1338/
      https://hackintosher.com/guides/guide-to-fresh-installing-macos-mojave-on-a-hackintosh-10-14/
       
       
      I have used UniBest to create my builds in the past and they have mostly been successful. I tried the other methods as a last resort. I have not gotten past the Apple boot screen with any method attempting to install Mojave. 
       
       

       
       
       
      I have followed all the guides I can in order to get a successful install. However, it has been hard to get a definitive guide to solve my issues.
       
       
      Could somebody please help me with the correct [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url] settings. Ie UEFI Boot Mode or Legacy Boot Mode? 
      Recommended BIOS Settings for my system. 
       
       
      It might also just be the required Clover boot screen setup / flags 
       
       
       
      I also have no clue which [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url] configurations are required for me to build.
       
       
       
      Any help at all will be most appreciated.
       
       
      I can post any more information regarding errors and crashes if required.       
       
       
       
       
       
×