-
Similar Content
-
By RougeOne
Budget Workstation MacOS 10.14.1 build: z370 AORUS Gaming 5 - i5-8600K - RX 580 - UHD 630
flawless iGPU/dGPU integration, fast FCPX editing/rendering, great overall performance for ~$1200 / ~£1000
Update: updated WhateverGreen and Lilu, then updated OS to 10.14.3 and everything is fine! Even iMessage, which previously I hadn't been able to make work, is now working - possibly the update flushed the NVRAM?
I'm gonna come straight out and admit it - I used newb tools which are considered taboo on InsanelyMac, and so this isn't so much an installation guide as it is a green flag to anyone considering the same hardware. My first and previous Hackintosh project was just over ten years ago and this site was massively helpful, so this is my (very small) way of giving back.
EFI DIRECTORY
http://s000.tinyupload.com/index.php?file_id=97606131925137056003
HARDWARE
CPU: Intel i5-8600K 3.6GHz hexacore (contains UHD 630 iGPU)
CPU Cooler: be quiet! Pure Rock Slim (no paste needed, and fan facing front)
Mobo: GIGABYTE z370 AORUS Gaming 5 (WIFI)
RAM: 1x 8GB CORSAIR Vengeance LPX C16 2666MHz (in first slot)
GFX Card: Sapphire RX 580 NITRO+ SE
SATA: used ports 0, 1, 3, 5 (HDD problems when connected to port 4)
HDD: generic
DVD Drive: generic
PSU: EVGA 500W Semi Modular (but you should get 650W!)
Case: CoolerMaster CM590 III
Fans: 2x stock case fans (one sucky on front, one blowy on back), 3x be quiet! BL046 120mm fans (two blowy on top, one sucky on front). Airflow near-perfectly balanced.
ADVICE
With the Clover configuration, you want to pay close attention to all things relating to graphics. There are some specific settings for ACPI, Boot, Devices and Graphics which should be copied exactly in order to get the iGPU and dGPU to work in perfect harmony. For instance, make sure you use ig-platform-id 59120003 rather than 59120000 if you want FCPX to be usable. With the right settings, FCPX will not only run, but run flawlessly.
I was not able to figure out how to make NVRAM/PRAM behave itself, and I got errors when I tried to issue relevant commands. As a result, I could not at first get iMessage to work properly. It worked once on my first installation attempt but not from subsequent attempts. This Clover configuration therefore has no consideration whatsoever toward iMessage reliability - however, iMessage ended up working somehow, anyway - I noticed it after I'd updated to 10.14.3 but this may just have been coincidence.
Onboard WiFi does not work. There is no driver for it. I'm using wired ethernet to a bridge router as it was cheaper than getting a compatible PCI card.
Audio is working well after I installed the z370 audio patch, then the ALC1220 codecs, then AppleALC.
With kexts for generic 3rd party SATA and generic 3rd party eSATA, my HDDs and DVD drive work perfectly well.
Sleep/Wake functions run perfectly. iCloud functions run perfectly. Shutdown leaves the mobo LEDs on, annoyingly.
My USB 3 ports seem to suffer from low power output, and I don't know why.
Overall, this system appears to run about as well under MacOS 10.14 Mojave as it does under Windows 7. I would solidly recommend this build to anyone looking to build a computer for workstation purposes, on a budget.
-
By JhonneR
Good morning, everyone, I'm sorry if I was wrong in choosing the topic but I need help.
I have found it extremely difficult to mount a Hackintosh in my acer.
Setup;
I5 2430m 2.4 6GB RAM
Mobo P5we0 - Intel intel Graphics 3000
At the moment I have not found out what my audio codecs are.
but I'll leave the link on the motherboard.
however, my real problem is several.
I have already used the itakos image, I have already used several images that could be installed normally and that after installing the image I do not have internet via cable or wireless.
And another, I already looked in other forums and I know that I will be called a donkey in the logical question but I have not been able to install the [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url] or clover to start from the Hard Disk, so I do not know what to do.At the moment I still do not know if there has already been someone who has already installed the High Sierra or just the Sierra in this notebook model and obtained permanent success.
If anyone can help me, I'll be grateful.
Installations without success, but with the system already installed in ACER;
SIERRA
HIGH SIERRA
MOJAVE
All with the same symptom. Starting only by the bootable USB stick and without internet connection via cable and wireless.
Appreciate ! Acer 5750 Official Page -
By Slice
Since rev 4844 Vector Themes are supported and there are ready-to-use Clovy by Clovy, cesium by Slice and BGM_SVG by Blackosx.
You may see it's structure to create own theme
-------------------------------------------------------------------------------------------------------------------------------------------------------
Now I want to add vector graphics support in Clover. See rev 4560 and later.
It is not working yet but designers may begin to create Vector Themes.
It supposed to consist of SVG elements and has design size. It will be rendered to any screen size scaled from design size.
What application in macOS can create SVG graphics?
Inkscape is not working in macOS 10.11+. Pity.
LibreOffice Draw works with SVG but buggy.
Boxy SVG cost 10$ but looks good enough. It creates the best in simplicity files and have more then enough features.
Illustrator is good but expensive.
How to improve SVG file?
Clover has restricted support for SVG. It is your job to make compatible file and as small as possible to speedup rendering.
Some helps:
Help:Inkscape – From invalid to valid SVG Inkscape files
From invalid to valid SVG Adobe Illustrator files
From invalid to valid SVG files of other editors: BKchem, ChemDraw and CorelDRAW
Help:Illustrator – Assistance with creating and saving SVG images in Adobe Illustrator that will pass W3C validation
User:Quibik/Cleaning up SVG files manually
Later I will write own instructions specific to Clover abilities.
How to create SVG fonts?
You can google to find ready-to-use SVG fonts. I found some problems with too beaty fonts: slow rendering and overflow crash. Be careful.
You can get ttf or otf fonts and convert them into svg by using online WEB services. Not a problem to google.
But then I want to find a way to simplify the font to reduce a size and speedup rendering.
You can create own font by FontForge It is opensource and available for Windows, Mac and GNU+Linux. It creates otf font which you can convert to svg font.
Pictures from Badruzeus
https://www.insanelymac.com/forum/applications/core/interface/file/attachment.php?id=301597
-
By gengik84
Ciro82==>>Thanks
Uno dei tre Requisiti:
Hack funzionante Mac vero Macchina virtuale Impostazioni Bios per il boot:
Cercate una voce del tipo “Sata Mode”e settatela in AHCI
Secure Boot: disabilitare o altri sistemi operativi
CSM: UEFI o LEGACY, oppure a secondo del tipo di installazione
VT-x / VT-d disable
*Nota: Secure boot e csm valido solo per bios UEFI
Materiale Occorrente
"OS X (Versione App.Store)”
USB 8GB *nota: nel caso di usb superiori dovrà essere partizionata, in modo da avere una partizione su cui "lavoreremo,di questa dimensione
ShowAllfiles
kext Wizard
Bootloader Clover_2.3k_r xxx: http: //sourceforge.n.../cloverefiboot/
Clover Configurator: http: //mackie100proj...a.org/download/
FakeSmc.kext: https://github.com/kozlek/HWSensors/releases
In allegato,a fondo pagina troverete un "pacchetto" contenente : ShowAllfiles, Kext Wizard, FakeSmc.kext:
App alternative:
ESP Mounter Pro: per montare la partizione EFI
Vi illustrerò tre metodi per creare la usb, ma sono ben distinti… quindi usatene soltanto uno
Metodo 1: “Install Mac_OS_X.command” Metodo 2: “Create Install Media di Apple” Metodo 3: Metodo Manuale Alla fine delle preparazione dell’installer, tutti i metodi necessitano l’installazione del Bootloader Clover sulla a vostra USB.
“CONDIZIONI OBBLIGATORIE”
PUNTO 1: che la vostra usb sia stata preventivamente nominata USB (caratteri maiuscoli) Tabella di partizione GUID e la formattazione in Mac esteso Journaled.
PUNTO 2: che l’installer di OSX si trovi in Applicazioni
Utility Disco
Selezionate la pendrive, andate su “partizione”, selezionate “1 partizione”, impostate Mac OS esteso journaled e date il nome USB, poi in basso cliccate su opzioni e scegliete Tabella partizione (GUID), poi “applica”.
Immagine
Riporto nuovamente l’operazione sopra citata adoperando dal nuovo Utility Disco introdotto su El Capitan.
Rimane ovviamente invariato nome della usb in ==>> USB (maiuscolo), la formattazione in Mac esteso Journaled e sia la mappa partizione in GUID
Da utility disco selezionate la usb, cliccate su inizializza.
dal menù a tendina scegliete la relative impostazioni
Immagine
Procedura effettua da High Sierra è la stessa della precedente, l'unica attenzione e operazione da aggiungere in primis è cliccare nel menù a tendina in alto sulla sinistra di utility disco e selezionare "mostra tutti i dispositivi"
Immagine
=====================
METODO 1: "Install_Mac_OS_X.Command" Lo script che trovate allegato in fondo alla guida permette la creazione dell’installer in maniera automatica
Include la possibilità di scelta di tre versioni di osx
Yosemite El Capitan Sierra Il risultato finale è come quello del metodo "manuale" descritto nella guida, per cui l'installazione avverrà in un solo passaggio, non in due come con il metodo createinstallmedia.
Offre inoltre la possibilità di inserire un kernel patchato, utile, per esempio, per chi usa AMD.
Rimane invariato il nome dato alla usb in USB, mappa partizione e tipo di formattazione
Se la vostra usb non sarà rinominata nel modo corretto, verrete avvisati dal terminale, quindi non dovrete far altro che apportare la relativa modifica e rilanciare nuovamente lo script
Esempio
===========================
Metodo 2
L'intento è quello di usare la procedura fornitaci direttamente da Apple, "createinstallmedia", introdotta con Mavericks.
Tale metodo prevede l’uso del terminale che via via se ne sta perdendo il “valore e l’uso”
Inizialmente per i neofiti potrà sembrare problematico ma alla fine non è così.
Durante il post installazione alcune operazioni ne richiedono l’ uso.
Perciò mi sono chiesto perchè, qualora uno volesse, non far conoscere da subito un po’ questo “strumento”???
Per favorirvi vi ho allegato i comandi già “pronti”, i quali li potrete copiare ed incollare sul terminale.
A questo punto aprite il terminale, copiate ed incollate il comando sottostante e premete invio, digitate la vostra password e premete nuovamente invio.
Comando per creare USB con Yosemite:
sudo /Applications/Install\ OS\ X\ Yosemite.app/Contents/Resources/createinstallmedia --volume /Volumes/USB --applicationpath /Applications/Install\ OS\ X\ Yosemite.app --nointeraction
Comando per creare USB con El Capitan
sudo /Applications/Install\ OS\ X\ El\ Capitan.app/Contents/Resources/createinstallmedia --volume /Volumes/USB --applicationpath /Applications/Install\ OS\ X\ El\ Capitan.app --nointeraction Comando per creare USB con Sierra
sudo /Applications/Install\ macOS\ Sierra.app/Contents/Resources/createinstallmedia --volume /Volumes/USB --applicationpath /Applications/Install\ macOS\ Sierra.app/ --nointeraction Per creare USB con Hight Sierra o Mojave usate --> C_I_M (aggiornato per 10.14)
Funziona con il drag & drop sul terminale, in questo caso non vi è necessità che la usb sia nominata in un determinato modo ed essendo basato su create install media ovviamente funziona da 10.9 a 10.14....
BENE…IL PROCESSO DI CREAZIONE E’ INIZIATO…
AVREMO CIRCA 20/30 MINUTI DI TEMPO LIBERO A CUI DEDICARSI A CIO’ CHE VOGLIAMO………………………………………..
COLGO L’OCCASIONE PER FARVI NOTARE LA VELOCITA’ E LA SICUREZZA DI QUESTO METODO
CONFRONTATE QUESTO CON IL TERZO METODO E NOTERETE CHE CON UN SOLO PASSAGGIO, OSSIA IL COMANDO DATO AL TERMINALE, FACCIAMO IN UNA SINGOLA OPERAZIONE TUTTI I VARI STEP DESCRITTI SULL’ ALTRO METODO.
DETTO QUESTO, MOLTO IMPORTANTE E’ SOTTOLINEARE CHE COSI’ FACENDO EVITEREMO ERRORI DI DISTRAZIONE RIGUARDO AI PASSAGGI O FRAINTENDIMENTI.
Immagine
Potete adesso passare ad installare il bootloader Clover sulla vostra usb.
*NOTA*:
Avendo usato questo metodo l'installazione si dividerà in due fasi, perciò dopo il primo riavvio e necessario far partire nuovamente l'installer, selezionare lo stesso disco senza formattarlo.
Finita questa ulteriore fase , l'installazione sarà terminata
=========================
METODO "MANUALE".... (lascio per futura memoria-Compatibile fino a 10.12)
==========================
Bootloader
**Nota:** Installazione in UEFI dipenderà dalla scheda madre in vostro possesso, quindi se non supporta tale opzione , il bootloader dovrà essere installato in modalità Legacy.
Vi invito, qualora non sapeste questa informazione, a recarvi nel sito ufficiale del produttore e controllare le informazioni a riguardo
Fatto questo dobbiamo installare Clover sulla usb.
A seconda del tipo di Bios o al tipo di installazione che vogliamo fare UEFI o Legacy avremo ovviamente configurazioni diverse in questa fase.
Lanciate il pkg.
Immagine
Cambiate la destinazione di installazione ad USB oppure Install Mac_OS_X (a secondo del tipo di creazione eseguita)
Successivamente clicchiamo su "Ad Hoc"
Per Installazione UEFI
Mettete i flag : Installazione solo per avvio UEFI
: installare Clover nella ESP
: Driver64UEFI AptioMemory --> (consigliato)
: Driver64UEFI ApfsDriverLoader --> (consigliato) --> sostituisce l'uso del driver apfs.efi
: Selezionate l'altri driver come da successiva immagine,
*Nota: Altri driver che si possono usare al suo posto sono:
informazioni
Proseguite con l’installazione.
Immagine
** Ricordate che avrete accesso a questa cartella dopo aver montato la partizione EFI**
===========================
Per installazione Legacy
Immagine
===========================
Impostazione per config.plist:
Con clover configurator “montate” la partizione EFI della usb.
1) Per fare questo nel menù di sinistra, cliccate su “Mount EFI”
2) individuate la partizione relativa alla vostra usb, a questo punto montiamo la relativa partizione EFI selezionando l’apposito pulsante “Mount Partition”
Immagine
3) Successivamente cliccate su “Open Partition”.. recatevi in EFI/Clover ed aprite il config.plist
4) Sezione ACPI: Disabilitate tutti i fix sia del menù 1 che del menù 2
Immagine
5) Sezione BOOT: Sole se si sta installando Yosemite mettete il flag su kext-dev-mode=1
Immagine
6) Sezione RT Variables: Se si sta installando El Capitan oppure Sierra, aggiungere i valori: BooterConfig= 0x28, CsrActiveConfig= 0x67
Immagine
7) Sezione System Parameters: Su inject kext mettete YES
Immagine
===========================
Nota: Su El Capitan, è stato introdotto SIP (System Integrity Protection)
Info:
===========================
Recatevi in EFI/Clover/kext/10.x
X= alla versione di osx che state installando. Per esempio se installerete Yosemite dovrete recarvi nella cartella 10.10, con El Capitan in 10.11….ecc
Se non ci fosse tale cartella, createla e nominatela voi a “modo”.
Copiatevi all’interno FakeSmc.kext
*Nota se venite già da altre vostre configurazioni, oltre kext sopra citato ,potete mettere gli altri necessari per il vostro hardware
Stessa cosa se avete DSDT e/o SSDT potete copiarli in EFI/Clover/Acpi/Patched
Immagine

Per High Sierra:
Scaricare il driver apfs.efi a fine guida, collocarlo:
--> EFI/clover/Driver64UEFI se stiamo usando UEFI
--> EFI/Clover/Driver64 se stiamo usando Legacy
Per chi volesse continuare ad usare HFS vi rimando a questo post:
Come installare High Sierra in HFS direttamente dalla usb
Utenti Laptop: Nel 99% è obbligatorio disattivare la grafica discreta Nvidia/Amd per installare questo nuovo osx
Quindi aggiungete --> SSDT-Disable_DGPU.aml.zip
in EFI/Clover/acpi/Patched della usb
--------------------------------------------------------------------
Per Mojave:
Scaricare il driver apfs.efi per 10.14 a fine guida, collocarlo:
--> EFI/clover/Driver64UEFI se stiamo usando UEFI
--> EFI/Clover/Driver64 se stiamo usando Legacy
Versione di clover non antecedente a V_4015
Volete usare HFS?
E' possibile fare un installazione diretta su altro disco o partizione, nel caso può essere usato anche per effettuare aggiornamenti...
nel caso guardate...
Mojave in HFS
Oppure direttamente da usb
Fatto questo avrete la vostra USB bootable per installare OSX.
………Non scordatevi Fakesmc.kext da mettere nella relativa cartella…. senza il quale non farete mai il Boot......
*NOTA: se usato il terminale per la creazione della usb, l'installazione si dividerà in due fasi, perciò dopo il primo riavvio e necessario far partire nuovamente l'installer, selezionare lo stesso disco senza formattarlo.
Finita questa ulteriore fase , l'installazione sarà terminata
**NOTA** Se avete processori Broadwell,Skylake o Kabylake...usate FakeSmc.kext e relativi sensors che trovate all'interno del secondo pacchetto.. (potete usarlo anche sui precedenti senza problemi, essendo una versione più aggiornata ha ulteriore supporto per le cpu più recenti)
Update: Fakesmc e sensors versione 6.26
Post installazione... post #2
Buon Hack….. 
Aggiornamento:Install_Mac_OS_X.command.zip (compatibile da 10.10 a 10.12)
le info le trovate a questo post
Ringrazio @Ciro82 che mi ha aiutato nel preparare questa guida.
Pacchetto.zip
Pacchetto-2.zip
apfs.efi-10.13-NoLog.zip
Pacchetto-Fake+Sensors 6.26.1440.zip
apfs.efi-10.13.1-No_LOG.zip
apfs.efi-10.13.2_No_Log.zip
apfs.efi-10.13.3-No_Log.zip
apfs.efi-10.13.4-No_Log.zip
apfs.efi-10.13.5_No_Log.zip
C_I_M.zip
apfs.efi-10.14-beta1_No_Log.zip
-
By blackosx
I've created a new tool to help with Clover vector themes. It's a perl script that will search and globally replace RGB hex colours in the format #000000 and replace them with new calculated RGB hex colours using the adjustments you ask for.
https://bitbucket.org/blackosx/cloversvgthemeadjuster
You can download it using:
git clone https://bitbucket.org/blackosx/cloversvgthemeadjuster.git See the usage instructions on the README.
Current Version
0.0.5 (changelog)
Overview
The script identifies all colours in the theme file and applies adjustments to the hue, saturation and lightness before saving a new file. The adjustments can be progressively increased in a loop to generate multiple files.
Example:
Using the following commands to adjust the hue:
perl AdjustThemeColour.pl -20 0 0 10 perl AdjustThemeColour.pl +20 0 0 10 Against my original Silver theme
Can generate multiple variations and choose one I like
Say, this one...
** Of course, this type of adjustment will not work on all themes. It all depends on what colours have been used in the design.
Or how about a de-saturated BGM_SVG?
Known Issues
- There's always a possibility that a newly replaced hex value may match an already existing hex value which is due to be changed afterwards. This would mean that the newly replaced colours will then be replaced incorrectly. The likely hood of this happening increases with the more colours used in the theme.
-