Jump to content
K0gen

Lenovo ThinkPad T420 with UEFI Only

4,869 posts in this topic

Recommended Posts

@Glasgreat - I came across this: http://www.macvidcards.com/store/p33/Wifi_AC_%26_Bluetooth_Airport_Card.html it has a  compatible card on a carrier module that does the pin out translation (read regular mini pci-e) That's what we need, With some tweaks to the chassis it should fit in. I'll see if I can get the adaptor card somewhere. It shall be good for the other Apple WiFi/BT combos as well ;)

Share this post


Link to post
Share on other sites
Advertisement

Updated clover config.plist to get NVS4200 to work. However, it stays as a black screen. There seems to be some sort of conflict still. Is nvidia injection enabled by default? I think it should be off. Any way to turn off Nvidia graphics injection from clover boot menu by default?

 

 

Also, iMessage and Facetime don't work for me. Here is the code when I try to reload the Intel E1000e kext. Weird thing. Kext is present in /S/L/E

/System/Library/Extensions/IONetworkingFamily.kext/Contents/PlugIns/AppleIntelE1000e.kext failed to load - (libkern/kext) not found; check the system/kernel logs for errors or try kextutil(8).

Further system info explaining the error;

Aug 24 14:34:08 daniels-mbp sudo[481]: m1kr0t3k : TTY=ttys001 ; PWD=/Volumes/Files ; USER=root ; COMMAND=/sbin/kextload /System/Library/Extensions/IONetworkingFamily.kext/Contents/PlugIns/AppleIntelE1000e.kext
Aug 24 14:34:08 daniels-mbp com.apple.kextd[12]: Can't open CFBundle for /System/Library/Extensions/IONetworkingFamily.kext/Contents/PlugIns/AppleIntelE1000e.kext.
Aug 24 14:34:08 --- last message repeated 1 time ---
Aug 24 14:34:08 daniels-mbp com.apple.kextd[12]: Error: Kext /System/Library/Extensions/IONetworkingFamily.kext/Contents/PlugIns/AppleIntelE1000e.kext - not found/unable to create.


Share this post


Link to post
Share on other sites

@adrenalation - 

 

perhaps the inability to load the kext is a permission problem? how did you install the kext?

i would reinstall the kext with kextutility or fix perms and do this following so it will rebuild the caches.

sudo touch /System/Library/Extensions

@manwe150 

 

i will try the DMAR table drop to see what that does for us. i don't really know how measure the effect of VT-d as fusion and/or virtual box runs for me. i have a windows VM that runs from a physical VMDK (i.e. the vmdk reads/writes the partition. another one is sitting on an SSD (and start up is very fast!). 

Share this post


Link to post
Share on other sites

@tluck - you can see that by running another VM inside the first one. Fusion for example allows for ESXi to host several VMs simultaneously. Or you run a Linux VM in VMware Workstation on a Windows VM in VMware Fusion.

Share this post


Link to post
Share on other sites

I am following this guide for installing OSX Mavericks 10.9.4 on

 

Thinkpad T420

UEFI BIOS v1.36

 

I am unable to boot from USB to install OSX.

 

Please help.

Share this post


Link to post
Share on other sites

@manwe150 - sure enough!  dropped DMAR table via clover, enabled VT-d in bios ... and what do you know?! OS X boots up fine.  

 

but it is not clear whether VMware Fusion even implements VT-d - which i think it does not. however, it already supports and can use VT-x/EPT (for VMs in VMs) and so on.  seems some newer thunderbolt macs seem to support VT-d on IvyBridge but i have not done a ton research on this so... 

 

anyway it doesn't seem to hurt anything - that is, dropping the DMAR table!? so i suppose it will be part of the new bundle going forward unless someone has a good reason to leave it there.


@viraf - you need to provide a bit more information. 

 

how did you create the USB - is it GPT/GUID?

are you able to select the USB and see the clover menu?

did you select the installation? 

where does it stop exactly?

is VT-d on or off in Security settings in the BIOS?

Share this post


Link to post
Share on other sites

@tluck

 

created the USB as per the instructions in the main post. Created USB with GUID. 

 

No i am not able to see clover menu

 

Yes. VT-d is off in security settings.

 

It keeps coming back to the BIOS boot Manager showing boot menu.

 

Thanks for your reply

Share this post


Link to post
Share on other sites

If it keeps going back to the boot selection menu aka the f12 menu, then it's not finding bootx64.efi Your partitions on the USB could be wrong or your clover installation could be wrong/missing.

 

Try following the guide again, carefully. If it still fails, post your partition info and verify that /efi/clover exists and has files.

Share this post


Link to post
Share on other sites

About vmware and real partition:

diskutil list

/dev/disk0

   #:                       TYPE NAME                    SIZE       IDENTIFIER

   0:      GUID_partition_scheme                        *500.1 GB   disk0

   1:                        EFI EFI                     209.7 MB   disk0s1

   2:                  Apple_HFS Power                   419.5 GB   disk0s2

   3:                 Apple_Boot Recovery HD             785.2 MB   disk0s3

   4:       Microsoft Basic Data WINDOWS                 79.7 GB    disk0s4

 

/Applications/VMware\ Fusion.app/Contents/Library/vmware-rawdiskCreator create /dev/disk0 4 /Users/Shared/Machines\ virtuelles/ ide

this cmd doesn't work why???

update : success added by add a new boot camp :)

the wm added doesn't boot (must boot from a usb win installer)

One solved :)

--

i lost FaceTime and message on my main disk (OK an a 2nd HD) :(

so i'm trying to find it back without changing too much things (Serial...) cos it works my 2nd HD

 

finally i decided to forget dual boot for the moment cos i have to reformat my main disk, install win 8.1 again, install 10.9 again then restore my information (disk0s2) on the disk

 

never forget that when you failed and tray again, you're learning :)

Share this post


Link to post
Share on other sites

@tetonne. 
 

running windows in a VM while using OS X is way better IMO!!! 

 

i had problems with IDE in VMware Fusion, so i use SCSI disks. 

 

in your case disk0 and partition 4

 

/Applications/VMware\ Fusion.app/Contents/Library/vmware-rawdiskCreator create /dev/disk0 4 "Disk1" lsisas

 

then my disks are defined like this in the vmx file

 

tluck@Toms-Mac /Local/W7x64-vmdk.vmwarevm

$ grep scsi Windows\ 7\ x64.vmx

scsi0.pciSlotNumber = "160"

scsi0.present = "TRUE"

scsi0.sasWWID = "50 05 05 64 59 da c3 60"

scsi0.virtualDev = "lsisas1068"

scsi0:0.fileName = "Disk1.vmdk"

scsi0:0.present = "TRUE"

scsi0:0.redo = ""

scsi0:1.fileName = "Disk2.vmdk"

scsi0:1.present = "TRUE"

scsi0:1.redo = ""

scsi0:2.fileName = "Disk3.vmdk"

scsi0:2.present = "TRUE"

scsi0:2.redo = ""

Share this post


Link to post
Share on other sites

If it keeps going back to the boot selection menu aka the f12 menu, then it's not finding bootx64.efi Your partitions on the USB could be wrong or your clover installation could be wrong/missing.

 

Try following the guide again, carefully. If it still fails, post your partition info and verify that /efi/clover exists and has files.

 

@tluck @Sheep_reaper

 

here is my diskutil list result for my usb

 

/dev/disk1

   #:                       TYPE NAME                    SIZE       IDENTIFIER

   0:      GUID_partition_scheme                        *32.7 GB    disk1

   1:                        EFI EFI                     209.7 MB   disk1s1

   2:                  Apple_HFS Install OS X Mavericks  8.0 GB     disk1s2

   3:                  Apple_HFS Untitled 2              24.2 GB    disk1s3

 

Also i have confirmed that i have EFI partition on my USB with following folders 

 

-BOOT

  - BOOTX64.efi

-CLOVER

- ACPI

- ACPI.1600x900
- CLOVERX64.efi
- config.1600x900.plist
- config.nodsdt.plist
- config.plist
- drivers64UEFI
- kexts
- misc
- themes
- tools
 
Please help.

Share this post


Link to post
Share on other sites

@glasgreat - so the mini pic-e board does pin out translation, since apple implemented another layout on its card. The card itself does both WiFi ac and Bluetooth 4LE. That's coming down to the Broadcom chip used. I place an order to get that card combo. Yes, it is expensive, but still cheaper than to fizzle around for ages (given I do earn around 68€/h).

Share this post


Link to post
Share on other sites

 

@tluck @Sheep_reaper

 

here is my diskutil list result for my usb

 

/dev/disk1

   #:                       TYPE NAME                    SIZE       IDENTIFIER

   0:      GUID_partition_scheme                        *32.7 GB    disk1

   1:                        EFI EFI                     209.7 MB   disk1s1

   2:                  Apple_HFS Install OS X Mavericks  8.0 GB     disk1s2

   3:                  Apple_HFS Untitled 2              24.2 GB    disk1s3

 

Also i have confirmed that i have EFI partition on my USB with following folders 

 

-BOOT

  - BOOTX64.efi

-CLOVER

- ACPI

- ACPI.1600x900
- CLOVERX64.efi
- config.1600x900.plist
- config.nodsdt.plist
- config.plist
- drivers64UEFI
- kexts
- misc
- themes
- tools
 
Please help.

 

 

Is it because the USB was formatted HFS+ ? Does the USB need to be FAT32 formatted?

Share this post


Link to post
Share on other sites

@viraf - your USB looks ok. since you have zip bundle on the USB, it has a HFS driver. 

 

check your bios 

(1) is it running 1.46 or 1.36 - upgrade if not 1.46

(2) check to make sure UEFI is enabled on the Startup menu. 

Set

UEFI - both (UEFI/Legacy) - or for this test just set to UEFI

UEFI First

Share this post


Link to post
Share on other sites

@viraf - your USB looks ok. since you have zip bundle on the USB, it has a HFS driver. 

 

check your bios 

(1) is it running 1.46 or 1.36 - upgrade if not 1.46

(2) check to make sure UEFI is enabled on the Startup menu. 

Set

UEFI - both (UEFI/Legacy) - or for this test just set to UEFI

UEFI First

I have BIOS 1.36 :(

Share this post


Link to post
Share on other sites

I have BIOS 1.36 :(

@tluck

 

With UEFI First set.

 

It boots into Intel boot agent and then shows 

 

MAC Address

 

DHCP/

 

Did not receive the boot file.

 

and jumps back to F12 Boot menu.

 

I do not wish to upgrade my bios is there a way it can be made to work with BIOS v1.36 ?

@viraf - 

 

i would update to bios 1.46. your old one probably can't recognize a 32GB usb! - if you have an older 8GB usb it may work with that old bios

 

bootable CD

from windows:

 

what about the UEFI settings - where they ok?

I will give it a try with 8GB USB disk however i had created a 8GB partitiiion in my 32GB USB disk for making the bootable

Share this post


Link to post
Share on other sites

@glasgreat -

 

you would probably only have to change DualLink=0 to DualLink=1

 

the difference between 1366x768 config.plist the 1600x900 config.plist are 2 items:

1) DualLink value

2) EDID only for 1600x900 screen (  alternate EDID is needed replace bogus/broken EDID from bios/panel with a good one for this panel size )

 

@viraf - it maybe the old bios only supports 2GB usb or less? i am sure you have a good reason not to upgrade your bios, because i can't think of one.

Share this post


Link to post
Share on other sites

@glasgreat -

 

you would probably only have to change DualLink=0 to DualLink=1

 

the difference between 1366x768 config.plist the 1600x900 config.plist are 2 items:

1) DualLink value

2) EDID only for 1600x900 screen (  alternate EDID is needed replace bogus/broken EDID from bios/panel with a good one for this panel size )

 

@viraf - it maybe the old bios only supports 2GB usb or less? i am sure you have a good reason not to upgrade your bios, because i can't think of one.

@tluck :) I have updated the BIOS using the bootable BIOS cd from lenovo site. but it still fails to go past the f12 boot menu.

 

:(

Share this post


Link to post
Share on other sites

@viraf - well, i would test a smaller USB (like 8GB). format it GUID and copy the zip to the EFI partition. then see it can see it boot clover, then put the mac install on it.

Share this post


Link to post
Share on other sites

@viraf - well, i would test a smaller USB (like 8GB). format it GUID and copy the zip to the EFI partition. then see it can see it boot clover, then put the mac install on it.

@tluck Thanks a lot. Was able to successfully install with the 8GB USB.

 

Just a small quick question. Can we safely upgrades provided by Software Update for system software ?

Share this post


Link to post
Share on other sites

@veer

- glad the install worked. good to know.  i have 1, 2, 4, 8, 16 GB usbs. so I have not tried a 32!

- yes.  i have been successful going from say 10.9.3 to 10.9.4 or 10.10 Yosemite DP to DP5 to DP6.

 

but it doesn't hurt to have a standby USB with the full install!

after you do such an update - don't forget you will have to replace the AppleHDA and Broadcom kexts (or more!)

Share this post


Link to post
Share on other sites

Any Idea why I can't sign in to iMessage? I have already fixed the e1000e kext for ethernet. stumped.....

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By Klaidonis
      I am making a minimal Clover build for the fastest boot possible with the boot6 file in legacy mode.
      While looking at the preboot.log, I noticed that there is a line without explanation (at 0:892). Apparently, whatever it is, the execution time of it is close to 2 seconds, more than 55% of the total logged boot time in the current configuration. This does not change whether I use USB 2 or USB 3 port.
       
      Is there a way to eliminate or speed up the above? Also, is there anything else you can suggest to improve the performance based on the below log file? Which moment in the boot process corresponds to the start time in preboot.log?  
      The last thing I would like to understand is the delay/timeout after the boot6 file has loaded, and the number 6 disappears from the screen. For about 2 seconds or slightly less, I can press any key, and then it will enter the BIOS-like interface from the boot6 file. Without further knowledge, it seems like those 2 seconds are just delay time, and only after that is CLOVERX64.efi actually started, which, I presume, is approximately when the preboot.log timer starts. So, if the aforementioned is correct, can I get rid of this delay as well? Note that I am using the boot1f32 file to chain-load boot6, which does not include the initial 2-second wait period for a keypress.
       
      === preboot.log ===
      0:100 0:100 MemLog inited, TSC freq: 2394459554 0:100 0:000 CPU was calibrated with ACPI PM Timer 0:100 0:000 LegacyRegion2: Chipset/proc: 0x0A048086 0:100 0:000 Next Generation Core processors (PAM 0x80-0x86) 0:100 0:000 Test PAM1=(0x41=90, 0x5a=90, 0x81=11, 0x91=00) at chipset 0A048086 0:100 0:000 , Install = Success 0:112 0:012 BiosVideoDriverBindingStart! 0:112 0:000 BiosVideoCheckForVbe 0:112 0:000 EdidOverride not found 0:121 0:009 Edid1+ 0:121 0:000 found Detail Timing 1920x1080 0:121 0:000 timing string after 0xFE:AUO 0:121 0:000 timing string after 0xFE:B156HAN01.2 0:122 0:000 0 1280x1024 attr=9B - ok, edid- 0:122 0:000 1 1024x768 attr=9B - ok, edid-, 1024x768, working, highest, pref=1 0:122 0:000 2 640x480 attr=9B - ok, edid-, 640x480, working 0:122 0:000 3 800x600 attr=9B - ok, edid-, 800x600, working 0:123 0:000 4 1920x1080 attr=9B - ok, edid+, working, highest, pref=4 0:123 0:000 BV new mode: 4 1920x1080 0:398 0:275 SetMode pref 4 (4) = Success 0:892 0:493 VGA Pci.Hdr.Command=6 - not enabled 2:623 1:731 2:623 0:000 Now is 21.02.2020, 13:03:21 (GMT) 2:623 0:000 Starting Clover revision: 5103 (master, commit 3f3b85da0) on CLOVER EFI 2:623 0:000 Build with: [Args: -D NO_GRUB_DRIVERS_EMBEDDED -t GCC53 | -D NO_GRUB_DRIVERS_EMBEDDED --conf=/Users/sergey/src/CloverHackyColor/Conf -D USE_LOW_EBDA -a X64 -b RELEASE -t GCC53 -n 5 | OS: 10.14.6] 2:623 0:000 SelfDevicePath=PcieRoot(0x0)\Pci(0x1D,0x0)\USB(0x0,0x0)\USB(0x4,0x0)\HD(1,MBR,0x04944021,0x3F,0x3BC1042) @940C9698 2:623 0:000 SelfDirPath = \EFI\CLOVER 2:623 0:000 SimpleTextEx Status=Success 2:623 0:000 === [ Get Smbios ] ======================================== 2:623 0:000 Type 16 Index = 0 2:623 0:000 Total Memory Slots Count = 2 2:623 0:000 Type 17 Index = 0 2:623 0:000 SmbiosTable.Type17->Speed = 1600MHz 2:623 0:000 SmbiosTable.Type17->Size = 4096MB 2:623 0:000 SmbiosTable.Type17->Bank/Device = BANK 0 DIMM0 2:623 0:000 SmbiosTable.Type17->Vendor = Hynix 2:623 0:000 SmbiosTable.Type17->SerialNumber = 00000000 2:623 0:000 SmbiosTable.Type17->PartNumber = HMT451S6MFR6A-PB 2:623 0:000 Type 17 Index = 1 2:623 0:000 SmbiosTable.Type17->Speed = 1600MHz 2:623 0:000 SmbiosTable.Type17->Size = 8192MB 2:623 0:000 SmbiosTable.Type17->Bank/Device = BANK 2 DIMM1 2:623 0:000 SmbiosTable.Type17->Vendor = Kingston 2:623 0:000 SmbiosTable.Type17->SerialNumber = 5A060A8A 2:623 0:000 SmbiosTable.Type17->PartNumber = KHX1600C9S3L/8G 2:623 0:000 Boot status=0 2:623 0:000 Running on: 'Aspire V5-573G' with board 'Dazzle_HW' 2:623 0:000 === [ GetCPUProperties ] ================================== 2:623 0:000 CPU Vendor = 756E6547 Model=40651 2:623 0:000 The CPU supported SSE4.1 2:623 0:000 BrandString = Intel(R) Core(TM) i7-4500U CPU @ 1.80GHz 2:623 0:000 The CPU supported turbo 2:623 0:000 MSR 0x35 20004 2:623 0:000 MSR 0xE2 before patch 1E008405 2:623 0:000 MSR 0xE2 is locked, PM patches will be turned on 2:623 0:000 MSR 0xCE 0008083D_F3011800 2:623 0:000 corrected FLEX_RATIO = 0 2:623 0:000 MSR 0x1B0 00000000 2:623 0:000 FSBFrequency = 71 MHz, DMI FSBFrequency = 100 MHz, Corrected FSBFrequency = 100 MHz 2:623 0:000 MaxDiv/MinDiv: 24.0/8 2:623 0:000 Turbo: 27/27/27/30 2:623 0:000 Features: 0xBFEBFBFF 2:623 0:000 Threads: 4 2:623 0:000 Cores: 2 2:623 0:000 FSB: 100 MHz 2:623 0:000 CPU: 1700 MHz 2:623 0:000 TSC: 1700 MHz 2:623 0:000 PIS: 100 MHz 2:623 0:000 ExternalClock: 25 MHz 2:623 0:000 === [ GetDevices ] ======================================== 2:623 0:000 GOP found at: PcieRoot(0x0)/Pci(0x2,0x0)/AcpiAdr(0x80010100) 2:623 0:000 PCI (00|00:00.00) : 8086 0A04 class=060000 2:623 0:000 PCI (00|00:02.00) : 8086 0A16 class=030000 2:623 0:000 - GOP: Provided by device 2:623 0:000 - GFX: Model=Intel HD Graphics 4400 (Intel) 2:623 0:000 PCI (00|00:03.00) : 8086 0A0C class=040300 2:623 0:000 PCI (00|00:14.00) : 8086 9C31 class=0C0330 2:623 0:000 PCI (00|00:16.00) : 8086 9C3A class=078000 2:623 0:000 PCI (00|00:1B.00) : 8086 9C20 class=040300 2:623 0:000 PCI (00|00:1C.00) : 8086 9C10 class=060400 2:623 0:000 PCI (00|00:1C.02) : 8086 9C14 class=060400 2:623 0:000 PCI (00|04:00.00) : 168C 0034 class=028000 2:623 0:000 - WIFI: Vendor=Atheros 2:623 0:000 PCI (00|00:1C.03) : 8086 9C16 class=060400 2:623 0:000 PCI (00|05:00.00) : 10EC 5287 class=FF0000 2:623 0:000 PCI (00|05:00.01) : 10EC 8168 class=020000 2:623 0:000 - LAN: 0 Vendor=Realtek 2:623 0:000 PCI (00|00:1C.04) : 8086 9C18 class=060400 2:624 0:000 PCI (00|01:00.00) : 10DE 0FE4 class=030200 2:624 0:000 PCI (00|00:1D.00) : 8086 9C26 class=0C0320 2:624 0:000 PCI (00|00:1F.00) : 8086 9C43 class=060100 2:624 0:000 PCI (00|00:1F.02) : 8086 9C03 class=010601 2:624 0:000 PCI (00|00:1F.03) : 8086 9C22 class=0C0500 2:624 0:000 === [ GetDefaultSettings ] ================================ 2:624 0:000 Clover load options size = 0 bytes 2:624 0:000 CheckOEMPathExists tried EFI\CLOVER\OEM\Aspire V5-573G--00-00-00-00-00-00. Dir not exists 2:624 0:000 CheckOEMPathExists tried EFI\CLOVER\OEM\Aspire V5-573G. Dir not exists 2:624 0:000 CheckOEMPathExists tried EFI\CLOVER\OEM\Aspire V5-573G-1700. Dir not exists 2:624 0:000 CheckOEMPathExists tried EFI\CLOVER\OEM\Dazzle_HW. Dir not exists 2:624 0:000 CheckOEMPathExists tried EFI\CLOVER\OEM\Dazzle_HW-1700. Dir not exists 2:624 0:000 set OEMPath by default: EFI\CLOVER 2:637 0:012 EFI\CLOVER\config.plist loaded: Success 2:637 0:000 === [ GetListOfThemes ] =================================== 2:637 0:000 === [ Found config plists ] =============================== 2:637 0:000 - config.plist 2:637 0:000 === [ GetEarlyUserSettings ] ============================== 2:637 0:000 timeout set to 0 2:637 0:000 Custom boot CUSTOM_BOOT_DISABLED (0x0) 2:637 0:000 Default theme: embedded 2:637 0:000 === [ LoadDrivers ] ======================================= 2:637 0:000 === [ InitScreen ] ======================================== 2:637 0:000 Console modes reported: 4, available modes: 2:637 0:000 - [01]: 80x25 2:637 0:000 - [02]: 80x50 2:637 0:000 - [03]: 100x31 2:637 0:000 - [04]: 240x56 (current mode) 2:637 0:000 SetScreenResolution: 1920x1080 - already set 2:637 0:000 SetScreenResolution: 1920x1080 - already set 2:637 0:000 reinit: self device path=PcieRoot(0x0)\Pci(0x1D,0x0)\USB(0x0,0x0)\USB(0x4,0x0)\HD(1,MBR,0x04944021,0x3F,0x3BC1042) 2:637 0:000 === [ GetMacAddress ] ===================================== 2:637 0:000 === [ ScanSPD ] =========================================== 2:637 0:000 Scanning SMBus [8086:9C22], mmio: 0xB3619004, ioport: 0x5040, hostc: 0x1 2:656 0:018 Slot: 2 Type 24 8192MB 1600MHz Vendor=Kingston PartNo=KHX1600C9S3L8G SerialNo=050A0006000A080A 2:657 0:000 === [ GetAcpiTablesList ] ================================= 2:657 0:000 Get Acpi Tables List from RSDT: 2:657 0:000 - [00]: FACP ACRPRDCT len=268 2:657 0:000 - [01]: UEFI ACRPRDCT len=566 2:657 0:000 - [02]: FPDT ACRPRDCT len=68 2:657 0:000 - [03]: ASF! ACRPRDCT len=165 2:657 0:000 - [04]: HPET ACRPRDCT len=56 2:657 0:000 - [05]: APIC ACRPRDCT len=140 2:657 0:000 - [06]: MCFG ACRPRDCT len=60 2:657 0:000 - [07]: BOOT ACRPRDCT len=40 2:657 0:000 - [08]: LPIT ACRPRDCT len=148 2:657 0:000 - [09]: ASPT ACRPRDCT len=52 2:657 0:000 - [10]: DBGP ACRPRDCT len=52 2:657 0:000 - [11]: SSDT ACRPRDCT len=1337 2:657 0:000 - [12]: SSDT ACRPRDCT len=2776 2:657 0:000 - [13]: SSDT ACRPRDCT len=12013 2:657 0:000 - [14]: SSDT ACRPRDCT len=11433 2:657 0:000 - [15]: SSDT ACRPRDCT len=2230 2:657 0:000 Calibrated TSC Frequency = 2394459554 = 2394MHz 2:657 0:000 === [ GetUserSettings ] =================================== 2:657 0:000 === [ Found DSDT tables ] ================================= 2:657 0:000 === [ ScanVolumes ] ======================================= 2:657 0:000 Found 8 volumes with blockIO 2:657 0:000 - [00]: Volume: PcieRoot(0x0)\Pci(0x1F,0x2)\Sata(0x0,0x0,0x0) 2:659 0:001 Result of bootcode detection: bootable Linux (grub,linux) 2:659 0:000 - [01]: Volume: PcieRoot(0x0)\Pci(0x1F,0x2)\Sata(0x1,0x0,0x0) 2:660 0:001 Result of bootcode detection: bootable unknown (legacy) 2:660 0:000 - [02]: Volume: PcieRoot(0x0)\Pci(0x1F,0x2)\Sata(0x0,0x0,0x0)\HD(1,GPT,8017BD66-1E24-4B31-8E09-BC49BECD6CC4,0x800,0x21330000) 2:661 0:001 Result of bootcode detection: bootable Windows (vista,win) 2:661 0:000 - [03]: Volume: PcieRoot(0x0)\Pci(0x1F,0x2)\Sata(0x0,0x0,0x0)\HD(2,GPT,82F3B738-65E9-458E-B2F1-BB55D4F00885,0x21331000,0x3D0800) 2:663 0:001 - [04]: Volume: PcieRoot(0x0)\Pci(0x1F,0x2)\Sata(0x0,0x0,0x0)\HD(3,GPT,E701DCD8-E3C5-4BFA-B61B-BFF4D80153FD,0x21701800,0x18C4F000) 2:664 0:001 - [05]: Volume: PcieRoot(0x0)\Pci(0x1F,0x2)\Sata(0x0,0x0,0x0)\HD(4,GPT,4DB1239A-A9D7-4045-A162-7EF1B3A5913B,0x3A350C21,0x3A3B616E) 2:665 0:001 Result of bootcode detection: bootable Windows (vista,win) 2:665 0:000 - [06]: Volume: PcieRoot(0x0)\Pci(0x1D,0x0)\USB(0x0,0x0)\USB(0x4,0x0) 2:677 0:011 Result of bootcode detection: bootable unknown (legacy) 2:677 0:000 USB volume 2:677 0:000 USB volume 2:677 0:000 - [07]: Volume: PcieRoot(0x0)\Pci(0x1D,0x0)\USB(0x0,0x0)\USB(0x4,0x0)\HD(1,MBR,0x04944021,0x3F,0x3BC1042) 2:688 0:011 Result of bootcode detection: bootable unknown (legacy) 2:688 0:000 USB volume 2:688 0:000 USB volume 2:688 0:000 This is SelfVolume !! 2:688 0:000 PutNvramPlistToRtVars: nvram.plist not found 2:689 0:000 No AudioIoProtocols, status=Not Found 2:689 0:000 === [ InitTheme ] ========================================= 2:689 0:000 use daylight theme 2:689 0:000 using embedded theme 2:689 0:000 got embedded sound 2:689 0:000 Channels: 2 Sample rate: 8000 Hz Bits: 16 2:689 0:000 output to channel 0 with volume 70, len=25600 2:689 0:000 sound channels=2 bits=16 freq=8000 2:689 0:000 sound converted to 48kHz 2:689 0:000 not found AudioIo to play 2:689 0:000 sound play end with status=Not Found 2:690 0:001 Using embedded font: Success 2:691 0:000 theme inited 2:691 0:000 Chosen embedded theme 2:691 0:000 after NVRAM boot-args= 2:691 0:000 === [ Dump SMC keys from NVRAM ] ========================== 2:691 0:000 no AppleSMC protocol 2:691 0:000 Entry scan disabled 2:691 0:000 === [ AddCustomTool ] ===================================== 2:692 0:000 === [ GetEfiBootDeviceFromNvram ] ========================= 2:692 0:000 Default boot entry not found 2:692 0:000 DefaultIndex=-1 and MainMenu.EntryCount=4 2:973 0:281 GUI ready  
    • By tluck
      Lenovo T460 macOS with Clover Guide
      Latest Release on GitHub (February 2020) Updated to Clover r5104 Updated Lilu based kexts - Lilu, ALC, WEG Updated acidanthera VoodooPS2 kext v2.1.1 the older 1.9 to the Misc Folder as an option.
        Various Tweaks over Last months The zip file is a complete Clover ESP (/EFI) bundle and kext pack for the Lenovo T460. The current file bundle is tested on Sierra. 
      Note: I never got the GFX fully working on El Capitan. 
      Full Clover file set - config.plist etc. Includes all custom kexts Includes custom DSDT/SSDT scripts and patches Utility scripts The zip bundles are posted to GitHub: https://github.com/tluck/Lenovo-T460-Clover/releases
      Caveat: The T460 systems used here was configured with: i5-6300U, Intel HD Graphics 520, 1920x1080 touch screen. If you have a different system model, then extract the ACPI files and use the included scripts to create a set of files consistent with your system type and BIOS version. See below for details.
      Credits: RehabMan, Shmilee, vusun123, TimeWalker, Mieze from which, much of their work and help is/was was used to get the T460 to this point.
      Devices and aspects working:
      Ethernet -  Intel I219LM is enabled via IntelMausiEthernext.kext WiFi/BT - substitute the Intel WiFi/BT with a compatible Broadcom or Atheros chip Audio - ALC293 codec implemented via AppleALC.kext (the old AppleHDA_ALC293 and CodecCommander kexts are not needed) PS2 - ClickPad + TrackPoint + all 3 buttons - using a modified VoodooPS2Controller to support new layouts - and added some custom Fn key maps based on 440/450 dsdt USB - implemented via custom SSDT + USBInjectAll kext. All USB3/USB2 ports are intel-based and work -  3 external USB and internal Camera, BT, etc  Sleep/Wake - the sleepwatcher package and custom sleep/wake scripts are used to help with sleep/wake for BT and PS2 devices. Note: have not tried to implement the SD card reader - no driver found.
      ACPI Files
      New Installation - Steps and Details
      Part 1 - OS Installation
      Part 2- Post OS Installation and Setup
      Notes on Custom Kexts
       
    • By Jancey
      I used this command: diskutil info disk0s2 | grep -i "Partition UUID" | rev | cut -d' ' -f 1 | rev

      But I accidentally removed the wrong disk and now my main windows drive is not appearing in the bootloader. I can't figure out how to get it back. I tried resetting my windows drive, but I kept getting an error. I also reset my mac and reinstalled Catalina.
    • By gengstapo
      @Hervé
       
      Im having similar issue with my HS setup, dell latitute 3480, i5-7200U
      Once the hdmi plugged in, the laptop display went blank, only could see the external tv
      But, when i put my laptop to sleep & wake up again, both screen got display (hdmi still connected)
      Even the hdmi could be plugged off & in (after sleep), the laptop display is fine
       
      What could be the culprit?
      Dell’s MacBook Pro IORegistry.zip
      config.plist.zip
    • By TomZanna
      Hi, I'm trying to install Mac Os Catalina on a HP 550-132NL.
      The system has:
      i7-6700
      RAM 12 GB
      GT 730
      LAN Realtek RTL8161
      ALC3863
       
      It passes the verbose phase but after the Apple logo goes away, it gets stuck on a grey screen and I can only move the pointer.
      Can I try to boot with the iGPU?
       
      origin.zip
      CLOVER_dGPU_USB_3.zip
×