Jump to content
K0gen

Lenovo ThinkPad T420 with UEFI Only

4,869 posts in this topic

Recommended Posts

if i roll back to AppleACPIPlatform.kext from 10.8.4 (v1.7) the speaker works fine after sleep. 

 

not sure what node you  are looking for in your kext.

 

i think the speaker output node is 0x1f (31)

headphone node is 0x19 (25)

 

Codec: Conexant CX20590
Address: 0
AFG Function Id: 0x1 (unsol 1)
Vendor Id: 0x14f1506e
Subsystem Id: 0x17aa21ce
Revision Id: 0x100002
No Modem Function Group found
Default PCM:
    rates [0x160]: 44100 48000 96000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM
Default Amp-In caps: N/A
Default Amp-Out caps: N/A
GPIO: io=4, o=0, i=0, unsolicited=1, wake=0
  IO[0]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
  IO[1]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
  IO[2]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
  IO[3]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
Node 0x10 [Audio Output] wcaps 0xc1d: Stereo Amp-Out R/L
  Control: name="Speaker Playback Volume", index=0, device=0
    ControlAmp: chs=3, dir=Out, idx=0, ofs=0
  Control: name="Speaker Playback Switch", index=0, device=0
    ControlAmp: chs=3, dir=Out, idx=0, ofs=0
  Device: name="CONEXANT Analog", type="Audio", device=0
  Amp-Out caps: ofs=0x4a, nsteps=0x4a, stepsize=0x03, mute=1
  Amp-Out vals:  [0x43 0x43]
  Converter: stream=0, channel=0
  PCM:
    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM
  Power states:  D0 D1 D2 D3 D3cold EPSS
  Power: setting=D0, actual=D0
Node 0x11 [Audio Output] wcaps 0xc1d: Stereo Amp-Out R/L
  Control: name="Headphone Playback Volume", index=0, device=0
    ControlAmp: chs=3, dir=Out, idx=0, ofs=0
  Control: name="Headphone Playback Switch", index=0, device=0
    ControlAmp: chs=3, dir=Out, idx=0, ofs=0
  Amp-Out caps: ofs=0x4a, nsteps=0x4a, stepsize=0x03, mute=1
  Amp-Out vals:  [0x43 0x43]
  Converter: stream=0, channel=0
  PCM:
    rates [0x560]: 44100 48000 96000 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM
  Power states:  D0 D1 D2 D3 D3cold EPSS
  Power: setting=D0, actual=D0
Node 0x12 [Audio Output] wcaps 0x611: Stereo Digital
  Converter: stream=0, channel=0
  Digital:
  Digital category: 0x0
  PCM:
    rates [0x160]: 44100 48000 96000
    bits [0xe]: 16 20 24
    formats [0x5]: PCM AC3
  Power states:  D0 D1 D2 D3 D3cold EPSS
  Power: setting=D0, actual=D0
Node 0x13 [beep Generator Widget] wcaps 0x70000c: Mono Amp-Out
  Control: name="Beep Playback Volume", index=0, device=0
    ControlAmp: chs=1, dir=Out, idx=0, ofs=0
  Control: name="Beep Playback Switch", index=0, device=0
    ControlAmp: chs=1, dir=Out, idx=0, ofs=0
  Amp-Out caps: ofs=0x07, nsteps=0x07, stepsize=0x0f, mute=0
  Amp-Out vals:  [0x00]
Node 0x14 [Audio Input] wcaps 0x100d1b: Stereo Amp-In R/L
  Control: name="Dock Mic Capture Volume", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=0, ofs=0
  Control: name="Dock Mic Capture Switch", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=0, ofs=0
  Control: name="Mic Capture Volume", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=1, ofs=0
  Control: name="Mic Capture Switch", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=1, ofs=0
  Control: name="Internal Mic Capture Volume", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=2, ofs=0
  Control: name="Internal Mic Capture Switch", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=2, ofs=0
  Device: name="CONEXANT Analog", type="Audio", device=0
  Amp-In caps: ofs=0x4a, nsteps=0x50, stepsize=0x03, mute=1
  Amp-In vals:  [0x80 0x80] [0x80 0x80] [0x4a 0x4a] [0x4a 0x4a]
  Converter: stream=0, channel=0
  SDI-Select: 0
  PCM:
    rates [0x160]: 44100 48000 96000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM
  Power states:  D0 D1 D2 D3 D3cold EPSS
  Power: setting=D0, actual=D0
  Connection: 4
     0x17 0x18 0x23* 0x24
Node 0x15 [Audio Input] wcaps 0x100d1b: Stereo Amp-In R/L
  Amp-In caps: ofs=0x4a, nsteps=0x50, stepsize=0x03, mute=1
  Amp-In vals:  [0x80 0x80] [0x4a 0x4a] [0x4a 0x4a] [0x4a 0x4a]
  Converter: stream=0, channel=0
  SDI-Select: 0
  PCM:
    rates [0x160]: 44100 48000 96000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM
  Power states:  D0 D1 D2 D3 D3cold EPSS
  Power: setting=D0, actual=D0
  Connection: 4
     0x17* 0x18 0x23 0x24
Node 0x16 [Audio Input] wcaps 0x100d1b: Stereo Amp-In R/L
  Amp-In caps: ofs=0x4a, nsteps=0x50, stepsize=0x03, mute=1
  Amp-In vals:  [0x80 0x80] [0x4a 0x4a] [0x4a 0x4a] [0x4a 0x4a]
  Converter: stream=0, channel=0
  SDI-Select: 0
  PCM:
    rates [0x160]: 44100 48000 96000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM
  Power states:  D0 D1 D2 D3 D3cold EPSS
  Power: setting=D0, actual=D0
  Connection: 4
     0x17* 0x18 0x23 0x24
Node 0x17 [Audio Selector] wcaps 0x30050d: Stereo Amp-Out
  Control: name="Dock Mic Boost Volume", index=0, device=0
    ControlAmp: chs=3, dir=Out, idx=0, ofs=0
  Amp-Out caps: ofs=0x00, nsteps=0x04, stepsize=0x27, mute=0
  Amp-Out vals:  [0x00 0x00]
  Power states:  D0 D1 D2 D3 D3cold EPSS
  Power: setting=D0, actual=D0
  Connection: 4
     0x1a* 0x1b 0x1d 0x1e
Node 0x18 [Audio Selector] wcaps 0x30050d: Stereo Amp-Out
  Control: name="Mic Boost Volume", index=0, device=0
    ControlAmp: chs=3, dir=Out, idx=0, ofs=0
  Amp-Out caps: ofs=0x00, nsteps=0x04, stepsize=0x27, mute=0
  Amp-Out vals:  [0x00 0x00]
  Power states:  D0 D1 D2 D3 D3cold EPSS
  Power: setting=D0, actual=D0
  Connection: 4
     0x1a* 0x1b 0x1d 0x1e
Node 0x19 [Pin Complex] wcaps 0x400581: Stereo
  Control: name="Headphone Jack", index=0, device=0
  Pincap 0x0000001c: OUT HP Detect
  Pin Default 0x042110ff: [Jack] HP Out at Ext Right
    Conn = 1/8, Color = Black
    DefAssociation = 0xf, Sequence = 0xf
  Pin-ctls: 0xc0: OUT HP
  Unsolicited: tag=01, enabled=1
  Power states:  D0 D1 D2 D3 D3cold EPSS
  Power: setting=D0, actual=D0
  Connection: 2
     0x10 0x11*
Node 0x1a [Pin Complex] wcaps 0x400481: Stereo
  Control: name="Dock Mic Jack", index=0, device=0
  Pincap 0x00001324: IN Detect
    Vref caps: HIZ 50 80
  Pin Default 0x21a190f0: [Jack] Mic at Sep Rear
    Conn = 1/8, Color = Pink
    DefAssociation = 0xf, Sequence = 0x0
  Pin-ctls: 0x24: IN VREF_80
  Unsolicited: tag=04, enabled=1
  Power states:  D0 D1 D2 D3 D3cold EPSS
  Power: setting=D0, actual=D0
Node 0x1b [Pin Complex] wcaps 0x400581: Stereo
  Control: name="Mic Jack", index=0, device=0
  Pincap 0x00011334: IN OUT EAPD Detect
    Vref caps: HIZ 50 80
  EAPD 0x2: EAPD
  Pin Default 0x04a11060: [Jack] Mic at Ext Right
    Conn = 1/8, Color = Black
    DefAssociation = 0x6, Sequence = 0x0
  Pin-ctls: 0x24: IN VREF_80
  Unsolicited: tag=03, enabled=1
  Power states:  D0 D1 D2 D3 D3cold EPSS
  Power: setting=D0, actual=D0
  Connection: 2
     0x10* 0x11
Node 0x1c [Pin Complex] wcaps 0x400581: Stereo
  Control: name="Dock Headphone Jack", index=1, device=0
  Pincap 0x00000014: OUT Detect
  Pin Default 0x212140ff: [Jack] HP Out at Sep Rear
    Conn = 1/8, Color = Green
    DefAssociation = 0xf, Sequence = 0xf
  Pin-ctls: 0x40: OUT
  Unsolicited: tag=02, enabled=1
  Power states:  D0 D1 D2 D3 D3cold EPSS
  Power: setting=D0, actual=D0
  Connection: 2
     0x10 0x11*
Node 0x1d [Pin Complex] wcaps 0x400581: Stereo
  Pincap 0x00010034: IN OUT EAPD Detect
  EAPD 0x2: EAPD
  Pin Default 0x40f001f0: [N/A] Other at Ext N/A
    Conn = Unknown, Color = Unknown
    DefAssociation = 0xf, Sequence = 0x0
    Misc = NO_PRESENCE
  Pin-ctls: 0x40: OUT
  Unsolicited: tag=00, enabled=0
  Power states:  D0 D1 D2 D3 D3cold EPSS
  Power: setting=D0, actual=D0
  Connection: 2
     0x10* 0x11
Node 0x1e [Pin Complex] wcaps 0x400481: Stereo
  Pincap 0x00000024: IN Detect
  Pin Default 0x40f001f0: [N/A] Other at Ext N/A
    Conn = Unknown, Color = Unknown
    DefAssociation = 0xf, Sequence = 0x0
    Misc = NO_PRESENCE
  Pin-ctls: 0x00:
  Unsolicited: tag=00, enabled=0
  Power states:  D0 D1 D2 D3 D3cold EPSS
  Power: setting=D0, actual=D0
Node 0x1f [Pin Complex] wcaps 0x400501: Stereo
  Control: name="Speaker Phantom Jack", index=0, device=0
  Pincap 0x00000010: OUT
  Pin Default 0x90170110: [Fixed] Speaker at Int N/A
    Conn = Analog, Color = Unknown
    DefAssociation = 0x1, Sequence = 0x0
    Misc = NO_PRESENCE
  Pin-ctls: 0x40: OUT
  Power states:  D0 D1 D2 D3 D3cold EPSS
  Power: setting=D0, actual=D0
  Connection: 2
     0x10* 0x11
Node 0x20 [Pin Complex] wcaps 0x400781: Stereo Digital
  Pincap 0x00000010: OUT
  Pin Default 0x40f001f0: [N/A] Other at Ext N/A
    Conn = Unknown, Color = Unknown
    DefAssociation = 0xf, Sequence = 0x0
    Misc = NO_PRESENCE
  Pin-ctls: 0x00:
  Unsolicited: tag=00, enabled=0
  Power states:  D0 D1 D2 D3 D3cold EPSS
  Power: setting=D0, actual=D0
  Connection: 1
     0x12
Node 0x21 [Audio Output] wcaps 0x611: Stereo Digital
  Converter: stream=0, channel=0
  Digital:
  Digital category: 0x0
  PCM:
    rates [0x160]: 44100 48000 96000
    bits [0xe]: 16 20 24
    formats [0x5]: PCM AC3
  Power states:  D0 D1 D2 D3 D3cold EPSS
  Power: setting=D0, actual=D0
Node 0x22 [Pin Complex] wcaps 0x400781: Stereo Digital
  Pincap 0x00000010: OUT
  Pin Default 0x40f001f0: [N/A] Other at Ext N/A
    Conn = Unknown, Color = Unknown
    DefAssociation = 0xf, Sequence = 0x0
    Misc = NO_PRESENCE
  Pin-ctls: 0x00:
  Unsolicited: tag=00, enabled=0
  Power states:  D0 D1 D2 D3 D3cold EPSS
  Power: setting=D0, actual=D0
  Connection: 1
     0x21
Node 0x23 [Pin Complex] wcaps 0x40040b: Stereo Amp-In
  Control: name="Internal Mic Boost Volume", index=0, device=0
    ControlAmp: chs=3, dir=In, idx=0, ofs=0
  Control: name="Internal Mic Phantom Jack", index=0, device=0
  Amp-In caps: ofs=0x00, nsteps=0x04, stepsize=0x2f, mute=0
  Amp-In vals:  [0x00 0x00]
  Pincap 0x00000020: IN
  Pin Default 0x90a60170: [Fixed] Mic at Int N/A
    Conn = Digital, Color = Unknown
    DefAssociation = 0x7, Sequence = 0x0
    Misc = NO_PRESENCE
  Pin-ctls: 0x20: IN
  Power states:  D0 D1 D2 D3 D3cold EPSS
  Power: setting=D0, actual=D0
Node 0x24 [Audio Mixer] wcaps 0x20050b: Stereo Amp-In
  Amp-In caps: ofs=0x4a, nsteps=0x4a, stepsize=0x03, mute=1
  Amp-In vals:  [0x00 0x00] [0x00 0x00]
  Power states:  D0 D1 D2 D3 D3cold EPSS
  Power: setting=D0, actual=D0
  Connection: 2
     0x10 0x11
Node 0x25 [Vendor Defined Widget] wcaps 0xf00000: Mono

Share this post


Link to post
Share on other sites
Advertisement

 

@pokenguyen - misunderstood your model is a T420S and not plain T420. here is a zip of the original dsdt and current dsdt.dsl (with comments) - you can diff them to see what was add/changed. 

 

attachicon.gift420_dsdt.zip

 

@okcakep

 

1) the sound loss from laptop speaker is known to be result of changes in 10.8.5 v1.8 AppleACPIPlatform.kext. laptop will lose speaker after wake from sleep. if you rollback to 10.8.4 v1.7 AppleACPIPlatform.kext this will not happen. 

 

@tluck --> sound now working after unplug my battery, im still using v1.8 AppleACPIPlatform.kext, i dont know way ? :)

 

2) EDID and glitches. is your native EDID different than the one Tetonne provided. is it v1.3? look for 0103 string vs 0104 string. i am injecting a different EDID (v1.3 seems work) than what was native/built-in to fix the glitches. 

 

in reality i never figured out why one EDID worked and another didn't. here were 2 v1.3 EDIDs for LCD 1600x900 - one was native (from windows) - i suspect it is the diff in detail clocking timings info? works is 96 Mhz and the glitchy one is 110 Mhz

 

works:

 

Extracted contents:
header:          00 ff ff ff ff ff ff 00
serial number:   30 e4 e2 02 00 00 00 00 00 14
version:         01 03
basic params:    80 1f 11 78 0a
chroma info:     43 45 97 59 57 8e 28 21 50 54
established:     00 00 00
standard:        01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01
descriptor 1:    80 25 40 80 60 84 1a 30 30 20 35 00 36 ae 10 00 00 19
descriptor 2:    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
descriptor 3:    00 00 00 fe 00 4c 47 20 44 69 73 70 6c 61 79 0a 20 20
descriptor 4:    00 00 00 fe 00 4c 50 31 34 30 57 44 32 2d 54 4c 42 31
extensions:      00
checksum:        38
 
Manufacturer: LGD Model 2e2 Serial Number 0
Made week 0 of 2010
EDID version: 1.3
Digital display
Maximum image size: 31 cm x 17 cm
Gamma: 2.20
Supported color formats: RGB 4:4:4, YCrCb 4:2:2
First detailed timing is preferred timing
Established timings supported:
Standard timings supported:
Detailed mode: Clock 96.000 MHz, 310 mm x 174 mm
               1600 1648 1680 1728 hborder 0
                900  903  908  926 vborder 0
               -hsync -vsync 
 

 

 

glitches:

 

Extracted contents:
header:          00 ff ff ff ff ff ff 00
serial number:   30 ae a1 40 00 00 00 00 01 14
version:         01 03
basic params:    80 1f 11 78 ea
chroma info:     cc ce 99 58 50 8e 26 24 4b 53
established:     00 00 00
standard:        01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01
descriptor 1:    f8 2a 40 9a 61 84 0c 30 40 2a 33 00 35 ae 10 00 00 18
descriptor 2:    cf 23 40 9a 61 84 0c 30 40 2a 33 00 35 ae 10 00 00 18
descriptor 3:    00 00 00 0f 00 a9 09 32 a9 09 32 19 09 00 06 af 56 31
descriptor 4:    00 00 00 fe 00 42 31 34 30 52 57 30 32 20 56 31 20 0a
extensions:      00
checksum:        7b
 
Manufacturer: LEN Model 40a1 Serial Number 0
Made week 1 of 2010
EDID version: 1.3
Digital display
Maximum image size: 31 cm x 17 cm
Gamma: 2.20
DPMS levels: Standby Suspend Off
Supported color formats: RGB 4:4:4, YCrCb 4:2:2
First detailed timing is preferred timing
Established timings supported:
Standard timings supported:
Detailed mode: Clock 110.000 MHz, 309 mm x 174 mm
               1600 1664 1706 2010 hborder 0
                900  903  906  912 vborder 0
               -hsync -vsync 
Detailed mode: Clock 91.670 MHz, 309 mm x 174 mm
               1600 1664 1706 2010 hborder 0
                900  903  906  912 vborder 0
               -hsync -vsync 

@Tluck, ok..i will try again for EDID

Share this post


Link to post
Share on other sites

Hi all,

 

i use this for X220 and 10.9 GM

 

I've got the same issue with no sound after sleep

 

If i reboot to osx or windows still no speaker.

 

I need to shutdown the computer to make it work.

 

i dont know if it's a codec issue (EAPD) or an appleacpiplatform issue

Share this post


Link to post
Share on other sites

ovof - thanks for adding your observation. seems to me appleacpiplatform since the v1.7 does not do this? but it is very weird that even that even windows can't revive the audio without a power down in between. i tested on my box and got no sound with win7. 

Share this post


Link to post
Share on other sites

Hi all,

 

i use this for X220 and 10.9 GM

 

I've got the same issue with no sound after sleep

 

If i reboot to osx or windows still no speaker.

 

I need to shutdown the computer to make it work.

 

i dont know if it's a codec issue (EAPD) or an appleacpiplatform issue

Back to AppleACPIPlatform 1.3.5 > Sound and sleep are working again

Share this post


Link to post
Share on other sites

System: 10.8.5

After upgrade from apple, no sound :hysterical:

Replace AppleHDA to old ( before ) working again sound

 

Sound after sleep, not tested..will be update again :D

 

Updated:

After sleep still no sound...

 

How to fix imessages ? i get msg : Your Apple ID "xxx@gmail.com" cant be used to set up IMessages at this time

 

If this is a new Apple ID you do not need to create another one. To use this Apple ID with iMessage, contact iMessage support with the code below :

Share this post


Link to post
Share on other sites

@okcakep 

 

10.8.5 updates 3 kexts we care about: AppleHDA, AppleACPIPlatform and AppleIntelCPUPowerManagement.

 

Last one is easy as Clover automatically patches it.

AppleHDA patched for 10.8.5 is in the latest zip, so you can replace the unmodified one.  

AppleACPIPlatform v1.8 (or 10.9.0 GM) seems to be problematic as it seems to nuke the speaker after sleep.  you can either live with it (a power off/on will reset it) or rollback to v1.7 from 10.8.4.

 

iMessage - there are lots of recipes to fix it... one key thing is to make sure ethernet is using en0 (first interface) - common problem since we have to add the ethernet driver and sometimes wifi or bluetooth picks it up.

 

@ovof - FYI, i found that rollback to AppleACPIPlatform v1.7 from 10.8.0-10.8.4 works too. 

Share this post


Link to post
Share on other sites

@okcakep 

 

10.8.5 updates 3 kexts we care about: AppleHDA, AppleACPIPlatform and AppleIntelCPUPowerManagement.

 

Last one is easy as Clover automatically patches it.

AppleHDA patched for 10.8.5 is in the latest zip, so you can replace the unmodified one.  

AppleACPIPlatform v1.8 (or 10.9.0 GM) seems to be problematic as it seems to nuke the speaker after sleep.  you can either live with it (a power off/on will reset it) or rollback to v1.7 from 10.8.4.

 

iMessage - there are lots of recipes to fix it... one key thing is to make sure ethernet is using en0 (first interface) - common problem since we have to add the ethernet driver and sometimes wifi or bluetooth picks it up.

 

@ovof - FYI, i found that rollback to AppleACPIPlatform v1.7 from 10.8.0-10.8.4 works too. 

@Tluck thank you for your advise...

 

Updated

For imessage, after add credit card number in app store, solved

Share this post


Link to post
Share on other sites

@okcakep 

 

10.8.5 updates 3 kexts we care about: AppleHDA, AppleACPIPlatform and AppleIntelCPUPowerManagement.

 

Last one is easy as Clover automatically patches it.

AppleHDA patched for 10.8.5 is in the latest zip, so you can replace the unmodified one.  

AppleACPIPlatform v1.8 (or 10.9.0 GM) seems to be problematic as it seems to nuke the speaker after sleep.  you can either live with it (a power off/on will reset it) or rollback to v1.7 from 10.8.4.

 

iMessage - there are lots of recipes to fix it... one key thing is to make sure ethernet is using en0 (first interface) - common problem since we have to add the ethernet driver and sometimes wifi or bluetooth picks it up.

 

@ovof - FYI, i found that rollback to AppleACPIPlatform v1.7 from 10.8.0-10.8.4 works too. 

 

Are there any key tips I should follow to do an upgrade from 10.8.5 to 10.9? Now that it is released and I use this actually as a work machine with 2 monitors I would love to get the enhanced multi-moniter support

 

Also: T420, i5, lower res screen, sound just never ever works :=)

 

Thanks!

Share this post


Link to post
Share on other sites

Hi!

Sorry for newbe question, but i try create first hackintosh in my life.

I have laptop Lenovo T430.

I download package for T420 from this manual: Clover UEFI on T420 Guide

Can i use this clover for install Mac OS as second OS (after licens Windows 8)?

Maybe i must change something? Kexts, DSDT?

Please help me.

Share this post


Link to post
Share on other sites

10.9 release.

Speaker still dead after sleep using current acpiplatform

 

@fungflex. The update will replace custom kexts in SLE. So the kext bundle in my zip will be needed to reinstall . There is a patched 10.9 applehda kext that when using the dsdt in the zip will give you sound. The layout id is set to 12 in the dsdt

 

@werewolfgsm. Yes u can. I dual boot. Not sure which of the t420 kexts apply. There are some 430 users on this thread and maybe they can supply a dsdt and info. Clover dsdt autopatch will make it work mostly But custom dsdt is generally better.

Share this post


Link to post
Share on other sites

10.9 release.

Speaker still dead after sleep using current acpiplatform

 

@fungflex. The update will replace custom kexts in SLE. So the kext bundle in my zip will be needed to reinstall . There is a patched 10.9 applehda kext that when using the dsdt in the zip will give you sound. The layout id is set to 12 in the dsdt

 

Thanks so much for the great help in this thread. I've got a fairly stable 10.8.5 build running now and my key plan for upgrading was:

  • Download release from App store on my other mac (already did this step)
  • Create bootable USB via new version of Lion Disk Maker (did this step too)
  • Install latest version of clover to the USB drive
  • Replace EFI folder on USB drive with one downloaded from your ZIP

 

At that stage, do I boot from the USB drive and select upgrade or do I need to wipe and do a fresh install. I've also never tried before, does the hackintosh community support usage of a time machine so I could back up my current environment and restore if I need to do a clean install from the flash drive.

 

Post install of 10.9 I just install the latest build of Clover? Also what is the best method to quickly install custom kexts post install?

 

Thanks!

 

 

 

Also has anyone else encountered a strange bug on their machine where the clock slowly over time becomes inaccurate? For example mine was showing 1:51 at 2:00 and if I open the preferences for time it connects and fixes itself.

 

Strange bug I just noticed.

Share this post


Link to post
Share on other sites

Well the actual clover package installation is good for stuff outside of the ESP. You can pretty much replace the EFI/Clover folder with the zip.yes time machine works. I updated my 10.8 install vs fresh

 

I used to have time issues with an old version of clover that did not compute the bus speed right. But now it does

Share this post


Link to post
Share on other sites

Thanks so much for the great help in this thread. I've got a fairly stable 10.8.5 build running now and my key plan for upgrading was:

  • Download release from App store on my other mac (already did this step)
  • Create bootable USB via new version of Lion Disk Maker (did this step too)
  • Install latest version of clover to the USB drive
  • Replace EFI folder on USB drive with one downloaded from your ZIP

 

At that stage, do I boot from the USB drive and select upgrade or do I need to wipe and do a fresh install. I've also never tried before, does the hackintosh community support usage of a time machine so I could back up my current environment and restore if I need to do a clean install from the flash drive.

 

Post install of 10.9 I just install the latest build of Clover? Also what is the best method to quickly install custom kexts post install?

 

Thanks!

 

 

 

Also has anyone else encountered a strange bug on their machine where the clock slowly over time becomes inaccurate? For example mine was showing 1:51 at 2:00 and if I open the preferences for time it connects and fixes itself.

 

Strange bug I just noticed.

It is better to do a clone of your 10 8.5 installation then doing a timemachine backup. Use CarbonCopyCloner for this task. If you have also Chameleon installed, you have to install it once again to your clone. The best bet for this task would be using an other hd for the clone.

 

Have fun.

Share this post


Link to post
Share on other sites

Thanks so much for the great help in this thread. I've got a fairly stable 10.8.5 build running now and my key plan for upgrading was:

  • Download release from App store on my other mac (already did this step)
  • Create bootable USB via new version of Lion Disk Maker (did this step too)
  • Install latest version of clover to the USB drive
  • Replace EFI folder on USB drive with one downloaded from your ZIP

 

At that stage, do I boot from the USB drive and select upgrade or do I need to wipe and do a fresh install. I've also never tried before, does the hackintosh community support usage of a time machine so I could back up my current environment and restore if I need to do a clean install from the flash drive.

 

Post install of 10.9 I just install the latest build of Clover? Also what is the best method to quickly install custom kexts post install?

 

Thanks!

 

 

 

Also has anyone else encountered a strange bug on their machine where the clock slowly over time becomes inaccurate? For example mine was showing 1:51 at 2:00 and if I open the preferences for time it connects and fixes itself.

 

Strange bug I just noticed.

Download release from App store on my other mac (already did this step) >> your sound will be death after upgrade from appstore. Restore your AppleHDA.kexts

No glitch in LCD

Replace /System/Library/Display/

 

Get your EDID using this

And I get EDID from Kogen Mantis from this post

 

My vendor id 0x30e4

convert to decimal > 16544

 

My product id 0x40A0

convert to decimal > 12516

 

And...configuration will be :

 

        <key>DisplayProductID</key>

        <integer>16544</integer>

        <key>DisplayProductName</key>

        <string>Color LCD</string>

        <key>DisplayRedGamma</key>

        <real>2.329986572265625</real>

        <key>DisplayRedPointX</key>

        <real>0.6454925537109375</real>

        <key>DisplayRedPointY</key>

        <real>0.337493896484375</real>

        <key>DisplayVendorID</key>

        <integer>12516</integer>

 

Ok..lets to AGPM eventhough my AGPM working without change Vendor ID.

 

go to sh-3.2# cd /System/Library/Extensions/AppleGraphicsPowerManagement.kext/Contents/  and edit Info.Plist

In here im edit Under

 

:                                <key>MacBookPro8,1</key>

                                <dict>

                                        <key>Vendor8086Device0116</key>  ---------------------------------> my device

                                        <dict>

                                                <key>BoostPState</key>

                                                <array>

                                                        <integer>0</integer>

                                                        <integer>1</integer>

                                                        <integer>2</integer>

                                                        <integer>3</integer>

                                                </array>

                                                <key>BoostTime</key>

                                                <array>

                                                        <integer>3</integer>

                                                        <integer>3</integer>

                                                        <integer>3</integer>

                                                        <integer>3</integer>

                                                </array>

                                                <key>Heuristic</key>

                                                <dict>

                                                        <key>BusyDownThresholdPercent</key>

                                                        <integer>65</integer>

                                                        <key>BusyUpThresholdPercent</key>

                                                        <integer>80</integer>

                                                        <key>DiagnosticModeDefault</key>

                                                        <integer>0</integer>

                                                        <key>EvaluateDownInterval</key>

                                                        <integer>350000</integer>

                                                        <key>EvaluateUpInterval</key>

                                                        <integer>66000</integer>

                                                        <key>ID</key>

                                                        <integer>2</integer>

                                                        <key>SensorOption</key>

                                                        <integer>1</integer>

                                                </dict>

                                                <key>HeuristicOld</key>

                                                <dict>

                                                        <key>ID</key>

                                                        <integer>1</integer>

                                                        <key>IdleInterval</key>

                                                        <integer>100</integer>

 

                                                        <key>SensorOption</key>

                                                        <integer>1</integer>

                                                        <key>Threshold_High</key>

                                                        <array>

                                                                <integer>50</integer>

                                                                <integer>75</integer>

                                                                <integer>96</integer>

                                                                <integer>100</integer>

                                                        </array>

                                                        <key>Threshold_High_v</key>

                                                        <array>

                                                                <integer>70</integer>

                                                                <integer>85</integer>

                                                                <integer>94</integer>

                                                                <integer>100</integer>

                                                        </array>

                                                        <key>Threshold_Low</key>

                                                        <array>

                                                                <integer>0</integer>

                                                                <integer>40</integer>

                                                                <integer>55</integer>

                                                                <integer>92</integer>

                                                        </array>

                                                        <key>Threshold_Low_v</key>

                                                        <array>

                                                                <integer>0</integer>

                                                                <integer>50</integer>

                                                                <integer>60</integer>

                                                                <integer>92</integer>

                                                        </array>

                                                </dict>

                                                <key>control-id</key>

                                                <integer>16</integer>    --------------------------> someone in forum suggest for macbookpro8,1 control-id should be 19

                                                <key>max-power-state</key>

                                                <integer>15</integer>

                                                <key>min-power-state</key>

                                                <integer>0</integer>

 

 

And..wow.....more bright ( in my opinion :thumbsup_anim: )

Share this post


Link to post
Share on other sites

Ok guys, I am at an odd stand still that I didn't experience at all when I put 10.7 or 10.8 on here....

 

I've been using LionDiskMaker and now Disk Maker X since they just pushed a brand new version tonight it seems. Even tried MyHack and I simply cannot get my Mavericks USB stick to be considered bootable. At the UEFI boot menu it doesn't show up at all.

 

If I try to do the installer from the 10.8.5 it tries to verify and fails saying contact AppleCare.

 

So for tonight, I remain on lowly Mountain Lion.

 

Thanks so much for that display tip above, once I'm in 10.9 I'll go through those steps too

Share this post


Link to post
Share on other sites

reread my instructions in this post #486  - it covers making USB, install and Post install. 

 

partition your USB stick GUID (use option) with 1 partition called USB

then run:

sudo /Applications/Install\ OS\ X\ Mavericks.app/Contents/Resources/createinstallmedia --volume /Volumes/USB --applicationpath /Applications/Install\ OS\ X\ Mavericks.app —nointeraction

 

EDID and glitches - the zip i posted has 2 configurations:

1) High Res 1600x900 - clover injects EDID inject that is glitch free - it is also in the DSDT

2) Low Res 1366x768 - need EDID that works for Low-res

 

the post 486 has a link that has DisplayOverride file to match the device ID 2e2 for High-Res - 

 

graphicsPM -  the DSDT now used IGPU instead of VID - so it looks up MacbookPro8,1 and sees IGPU - i don't have my system with me now so i can't test changing the control effects brightness. but the latest bundle edits the SNBFramebuffer kext to increase the LCD brightness. your profile looks like the one for HD Graphics (gen. 1) perhaps thats ok. 

 

                                <key>MacBookPro8,1</key>

                                <dict>

                                        <key>IGPU</key>

                                        <dict>

                                                <key>Heuristic</key>

                                                <dict>

                                                        <key>BusyDownThresholdPercent</key>

                                                        <integer>70</integer>

                                                        <key>BusyUpThresholdPercent</key>

                                                        <integer>90</integer>

                                                        <key>DiagnosticModeDefault</key>

                                                        <integer>0</integer>

                                                        <key>EvaluateDownInterval</key>

                                                        <integer>350000</integer>

                                                        <key>EvaluateUpInterval</key>

                                                        <integer>66000</integer>

                                                        <key>ID</key>

                                                        <integer>2</integer>

                                                        <key>SensorOption</key>

                                                        <integer>1</integer>

                                                </dict>

                                                <key>control-id</key>

                                                <integer>16</integer>

                                                <key>max-power-state</key>

                                                <integer>15</integer>

                                                <key>min-power-state</key>

                                                <integer>0</integer>

                                        </dict>

                                </dict>

Share this post


Link to post
Share on other sites

reread my instructions in this post #486  - it covers making USB, install and Post install. 

 

partition your USB stick GUID (use option) with 1 partition called USB

then run:

sudo /Applications/Install\ OS\ X\ Mavericks.app/Contents/Resources/createinstallmedia --volume /Volumes/USB --applicationpath /Applications/Install\ OS\ X\ Mavericks.app —nointeraction

 

EDID and glitches - the zip i posted has 2 configurations:

1) High Res 1600x900 - clover injects EDID inject that is glitch free - it is also in the DSDT

2) Low Res 1366x768 - need EDID that works for Low-res

 

the post 486 has a link that has DisplayOverride file to match the device ID 2e2 for High-Res - 

 

graphicsPM -  the DSDT now used IGPU instead of VID - so it looks up MacbookPro8,1 and sees IGPU - i don't have my system with me now so i can't test changing the control effects brightness. but the latest bundle edits the SNBFramebuffer kext to increase the LCD brightness. your profile looks like the one for HD Graphics (gen. 1) perhaps thats ok. 

 

                                <key>MacBookPro8,1</key>

                                <dict>

                                        <key>IGPU</key>

                                        <dict>

                                                <key>Heuristic</key>

                                                <dict>

                                                        <key>BusyDownThresholdPercent</key>

                                                        <integer>70</integer>

                                                        <key>BusyUpThresholdPercent</key>

                                                        <integer>90</integer>

                                                        <key>DiagnosticModeDefault</key>

                                                        <integer>0</integer>

                                                        <key>EvaluateDownInterval</key>

                                                        <integer>350000</integer>

                                                        <key>EvaluateUpInterval</key>

                                                        <integer>66000</integer>

                                                        <key>ID</key>

                                                        <integer>2</integer>

                                                        <key>SensorOption</key>

                                                        <integer>1</integer>

                                                </dict>

                                                <key>control-id</key>

                                                <integer>16</integer>

                                                <key>max-power-state</key>

                                                <integer>15</integer>

                                                <key>min-power-state</key>

                                                <integer>0</integer>

                                        </dict>

                                </dict>

 

 

@Tluck, before i change, i still get AGPM natively :) with IGPU detected.

I just try :)

 

No, my vga using HD3000 2nd gen Tluck :)

 

FYI, im still only get 69Hz for LCD Display

Share this post


Link to post
Share on other sites

Hey all,

 

I've been following this thread since I got my T530 at the beginning of September. Seems almost nobody has these / not much info on installing. I have it up and running with Mavericks right now via [url=&quot;http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/&quot;]#####[/url] method, but would much rather use proper UEFI and clover to do this, with a dsdt file. If I provide all pertinent information / dsdt / acpi dumps can someone help me patch a dsdt and get one going? i've tried before but can't get one to work. 

 

Just let me know what I need to provide and then we can try to get a solution. I'll be the first T530 guy and then we can have the dsdt etc posted for everyone to see / use

Share this post


Link to post
Share on other sites

Sorry, this is a dense question but I am suffering from too many TLAs (three letter acronyms)

 

Can I ask one of the wonderful ninjas here to help explain what these are?

 

ESP

SLE

AGPM

 

Status Update: I'm running Mavericks like a champ now and just trying to fix up my display issue now

Share this post


Link to post
Share on other sites

@FungFlex - sorry!

 

ESP - EFI System Partition - its the first (hidden/protected) partition on a GUID Partition Table formatted disk containing EFI files. where you put the Clover zip!

GUID - Globally Unique Identifiers

EFI - Extensible Firmware Interface

UEFI - Unified EFI

SLE - /S/L/E - /System/Library/Extensions

AGPM - AppleGraphicsPowerManagement

 

@humm3r - since you have it running using chameleon or chimera - a beast method right? then you are more than half way there! 

you can convert your MBR formatted disk to boot with Clover. Clover supports MBR/boot style as well as EFI/boot.efi style start up.

 

for EFI style then (which is what most of us are doing here) then you partition your disk with GPT/GUID and the OSX installers are happy.

Clover can auto-patch the built in DSDT to make it about 90% working for laptops. I don't know what audio the 530 may require a custom dsdt.

ages ago it seems, manwe150 posted a guide on what he did to patch the dsdt for the T420. the T420 DSDT has evolved a bit from there - mostly with tweaks for Audio/Video.

 

one thing you can do is use clover patching and then extract the patched DSDT (clover can do this too!) to then build upon that. i booted with a bunch of DSDT patch flags with virgin OS. i don't have my system with me now so i can't remember the so called DSDT mask or which ones to avoid etc.  you can test this pretty easily but using a USB to boot up clover.

Share this post


Link to post
Share on other sites

HI, I did my USB using the method at the first post at this topic and it runs very smooth when using Intel HD3000;

The first time I installed 10.8.3 in my Lenovo T420s, I used myHack method, I have a disk image of this installation.

I had some issues after updating to 10.8.5 and had to wipe out everything and reinstall. But the reinstallation came up without sound and USB 3.0; Then I restored my previous backup (from myHack method). Worked fine. Even iMessage and Face Time, with no issues!!

Yesterday, I downloaded 10.9 and installed as update, directly from Launchpad.

The boot became faster (12 sec)!! But then, follow the list:

1. Sound is working, but just after start playing something, the sound became sizzle

2. All applications that uses Apple ID is not working, can't log in;

 

I'm afraid to update the kexts with [url=&quot;http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/&quot;]#####[/url]. 

 

What yous guys suggest?

Share this post


Link to post
Share on other sites

 

2. All applications that uses Apple ID is not working, can't log in;

 

 

Try removing all your account settings completely and then adding it back. Also deleting your credit card on file and re-adding it could help. That worked for me back on 10.8

Share this post


Link to post
Share on other sites

Ok I seem to be stuck so I wanted to see if what I am doing is even correct to be honest. When I look at Finder I have two main hard drive volumes for my system EFI and Mac. I’ve been updating the files and dropped everything into the folders on EFI from the zip tluck provided.


 


This has everything working perfectly besides the display which is still showing up as quadrants.


 


When I attempt to install Clover again on the desktop it fails, and previously what made my display show up correct on 10.8.5 was simply selecting UEFI and then my Mac install during the boot process, that made everything boot properly. Now when I select UEFI it doesn’t seem to work, it just essentially refreshes the window so I can select UEFI endlessly or I can select my Mavericks install.


 


It seems like something is wrong with my Clover install but I can’t figure out what or how to fix it.


 


I went through all the steps on post #486 and it didn’t seem to resolve my issue, I even went and edited the .plist and turned dual link off as that was mentioned earlier in this thread. I’m trying to fix it now via my macbook air using splashtop so I can edit things without having to squint :-)

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Content

    • By tluck
      Lenovo T460 macOS with Clover Guide
      Latest Release on GitHub (February 2020) Updated to Clover r5104 Updated Lilu based kexts - Lilu, ALC, WEG Updated acidanthera VoodooPS2 kext v2.1.1 the older 1.9 to the Misc Folder as an option.
        Various Tweaks over Last months The zip file is a complete Clover ESP (/EFI) bundle and kext pack for the Lenovo T460. The current file bundle is tested on Sierra. 
      Note: I never got the GFX fully working on El Capitan. 
      Full Clover file set - config.plist etc. Includes all custom kexts Includes custom DSDT/SSDT scripts and patches Utility scripts The zip bundles are posted to GitHub: https://github.com/tluck/Lenovo-T460-Clover/releases
      Caveat: The T460 systems used here was configured with: i5-6300U, Intel HD Graphics 520, 1920x1080 touch screen. If you have a different system model, then extract the ACPI files and use the included scripts to create a set of files consistent with your system type and BIOS version. See below for details.
      Credits: RehabMan, Shmilee, vusun123, TimeWalker, Mieze from which, much of their work and help is/was was used to get the T460 to this point.
      Devices and aspects working:
      Ethernet -  Intel I219LM is enabled via IntelMausiEthernext.kext WiFi/BT - substitute the Intel WiFi/BT with a compatible Broadcom or Atheros chip Audio - ALC293 codec implemented via AppleALC.kext (the old AppleHDA_ALC293 and CodecCommander kexts are not needed) PS2 - ClickPad + TrackPoint + all 3 buttons - using a modified VoodooPS2Controller to support new layouts - and added some custom Fn key maps based on 440/450 dsdt USB - implemented via custom SSDT + USBInjectAll kext. All USB3/USB2 ports are intel-based and work -  3 external USB and internal Camera, BT, etc  Sleep/Wake - the sleepwatcher package and custom sleep/wake scripts are used to help with sleep/wake for BT and PS2 devices. Note: have not tried to implement the SD card reader - no driver found.
      ACPI Files
      New Installation - Steps and Details
      Part 1 - OS Installation
      Part 2- Post OS Installation and Setup
      Notes on Custom Kexts
       
    • By gengstapo
      @Hervé
       
      Im having similar issue with my HS setup, dell latitute 3480, i5-7200U
      Once the hdmi plugged in, the laptop display went blank, only could see the external tv
      But, when i put my laptop to sleep & wake up again, both screen got display (hdmi still connected)
      Even the hdmi could be plugged off & in (after sleep), the laptop display is fine
       
      What could be the culprit?
      Dell’s MacBook Pro IORegistry.zip
      config.plist.zip
    • By TomZanna
      Hi, I'm trying to install Mac Os Catalina on a HP 550-132NL.
      The system has:
      i7-6700
      RAM 12 GB
      GT 730
      LAN Realtek RTL8161
      ALC3863
       
      It passes the verbose phase but after the Apple logo goes away, it gets stuck on a grey screen and I can only move the pointer.
      Can I try to boot with the iGPU?
       
      origin.zip
      CLOVER_dGPU_USB_3.zip
    • By MaLd0n
      --Donations via PayPal--
      https://tinyurl.com/r2bvzm7
       
      --Original Topic--
      https://www.olarila.com/topic/6874-olarila-hackbook-lenovo-ideapad-s145-mojave-catalina-full-dsdt-patches/
       

       
      -Perfect HackBook, HDMI Audio/Video, Bluetooth, AirPlay, Sleep, Lid Sleep, Auto Sleep, Audio, etc!
      -Wifi card has been replaced with Dell DW1560!
      -I'm using a S145-15IWL Model with Intel Core i5 8265u / Intel UHD Graphics 620
      -Update bios/uefi to last version
       
      --Installation--
      https://www.olarila.com/topic/5794-guide-install-macos-with-olarila-image-step-by-step-install-and-post-install-windows-or-mac/
       
      --Clover Folder--
      Just paste EFI folder inside EFI partition
      https://www.olarila.com/files/Clover.Folder/Lenovo IdeaPad S145.zip
      Notebooks with ELAN trackpad use it with my folder above
      IdeaPad S145 ELAN.zip
       
      Bluetooth Broadcom
      Bluetooth Broadcom.zip
       
      CPUFriend for i5-8265U
      CPUFriend i5-8265U.zip
       
      --Full DSDT Patches--
      -My DSDT
      DSDT Lenovo IdeaPad S145.zip
       
      This DSDT work on S145-14IWL, S145-15IWL, V14-IWL, V15-IWL models
      -Patches
      -FIX ERRORS AND WARNINGS -REMOVE UNUSED SCOPES / DEVICES -HIGH PRECISION EVENT TIMER -SATA SERIE 11 ID -DMAC -REMOVE LINES, PROBLEMATIC and UNUSED -SLPB -DARWIN / WINDOWS 2015 -XHCI -PLUGIN TYPE -HDAS to HDEF -HDEF -REAL TIME CLOCK -ARTC -IRQs -SBUS -BUS1 -MCHC -ALS0 -SHUTDOWN -FWHD -USBX -PMCR -PPMC -XSPI -GMM -IMEI -EC -PRWs -_DSMs -PNLF -BRIGHTNESS KEYS -I2C -NATIVE USB -ARPT -GFX0 -DTGP -kUSBCompanionIndex -io-device-location -FULL RENAMED DEVICES   --IGPU Patch--
      Video solution with HDMI Audio and Video
      <key>PciRoot(0x0)/Pci(0x2,0x0)</key> <dict> <key>AAPL,GfxYTile</key> <data> AQAAAA== </data> <key>AAPL,ig-platform-id</key> <data> CQClPg== </data> <key>device-id</key> <data> pT4AAA== </data> <key>enable-hdmi20</key> <data> AQAAAA== </data> <key>framebuffer-con0-alldata</key> <data> AAAIAAIAAACYAAAA </data> <key>framebuffer-con0-enable</key> <integer>1</integer> <key>framebuffer-con1-alldata</key> <data> AQEJAAAIAADHAQAA </data> <key>framebuffer-con1-enable</key> <integer>1</integer> <key>framebuffer-con2-alldata</key> <data> AgYKAAAEAADHAQAA </data> <key>framebuffer-con2-enable</key> <integer>1</integer> <key>framebuffer-fbmem</key> <data> AACQAA== </data> <key>framebuffer-patch-enable</key> <data> AQAAAA== </data> <key>framebuffer-stolenmem</key> <data> AAAwAQ== </data> <key>framebuffer-unifiedmem</key> <data> AAAAgA== </data> <key>hda-gfx</key> <string>onboard-1</string> <key>model</key> <string>Intel Corporation, Cannon Point-LP Iris Plus Graphics 655</string> </dict>   --Native USB Fix for Notebooks - No Injector/Kext Required--
      https://www.olarila.com/topic/6878-guide-native-usb-fix-for-notebooks-no-injectorkext-required/
      https://www.olarila.com/topic/6181-guide-native-usb-fix-for-desktops-no-injectorkext-required-skylake/
       
       
      -ScreenShots

































      -Links
       
       
      Clover https://github.com/CloverHackyColor/CloverBootloader
      AirportBrcmFixup.kext https://github.com/acidanthera/AirportBrcmFixup
      AppleALC.kext https://github.com/acidanthera/AppleALC
      Brcm Bluetooth https://github.com/acidanthera/BrcmPatchRAM
      Lilu.kext https://github.com/acidanthera/Lilu
      SystemProfilerMemoryFixup.kext https://github.com/Goldfish64/SystemProfilerMemoryFixup
      VirtualSMC.kext https://github.com/acidanthera/VirtualSMC
      VoodooI2C.kext https://github.com/alexandred/VoodooI2C
      VoodooPS2Controller.kext https://github.com/acidanthera/VoodooPS2
      WhateverGreen.kext https://github.com/acidanthera/WhateverGreen
      MaciASL - https://github.com/acidanthera/MaciASL
      acpica - https://github.com/acpica/acpica
      AptioMemoryFix.efi https://github.com/acidanthera/AptioFixPkg
      ApfsDriverLoader.efi https://github.com/acidanthera/AppleSupportPkg
      HFSPlus.efi https://github.com/JrCs/CloverGrowerPro/blob/master/Files/HFSPlus/X64/HFSPlus.efi?raw=true
      Hackintool https://github.com/headkaze/Hackintool
       
      -Credits and thanks to the old and new people in the community who developed patches, kexts and bootloaders!
       
      Slice, Kabyl, usr-sse2, jadran, Blackosx, dmazar, STLVNUB, pcj, apianti, JrCs, pene, FrodoKenny, skoczy, ycr.ru, Oscar09, xsmile, SoThOr, RehabMan, Download-Fritz, Zenit432, cecekpawon, Intel, Apple, Oracle, Chameleon Team, crazybirdy, Mieze, Mirone, Oldnapalm, netkas, Elconiglio, artut-pt, ErmaC, Pavo, Toleda, Master Chief and family, bcc9, The King, PMheart, Sherlocks, Micky1979, vit9696, vandroiy2013, Voodoo Team, Pike R. Alpha, lvs1974, Austere.J, CVad, Sampath007, onemanosx, erroruser, Jenny David, Olarila Facebook Community, Hackintosh Facebook Community and many others!
       
      We're all here to have fun and learn from each other!
    • By mikezexter
      (Dear moderators please replace this topic to another category if I made a mistake in choosing it)
       
      Hello everybody. I need some help in trying to fix native AppleHDA sound on my X230T.
      VoodooHDA works perfectly but without needed HDMI audio channel so I need to try fix my sound in native mode.
       
      AppleALC told us here (README) that in v1.2.1 Added ALC269 layout-id 18 for Thinkpad X230 by Hypereitan. And if it works I didn't need to create this topic.  Unfortunately layout ids 1,2,3,18 and 55 didn't help me to fix sound issue.
       
      My Clover: https://drive.google.com/open?id=1FuGS7iE59ydgiMsxZcDMarlAFH3FliNE (it's 2 MB bigger than I could upload for now)
      I've also uploaded some screenshots of what I've seen after 5 reboots in a row changing layout ids. Please help me to fix this issue.
       
×