Jump to content
Kogen Mantis

Lenovo ThinkPad T420 with UEFI Only

4,531 posts in this topic

Recommended Posts

28 minutes ago, tluck said:

but you are able to boot Snuk's 1.52 DSDT right? (other than the ACPIBatteryManager issue?)

Ah, I can use your aml with lower version of clover, and when I use Snuk aml it KP about 2 times then It can boot into OS normaly, and it loop that progress again and again after every restart or start up! So strange!

Edited by SuperReaper

Share this post


Link to post
Share on other sites
Advertisement
4 hours ago, SuperReaper said:

Ah, I can use your aml with lower version of clover, and when I use Snuk aml it KP about 2 times then It can boot into OS normaly, and it loop that progress again and again after every restart or start up! So strange!

can you try this one? what is KP all about?

DSDT.zip

Share this post


Link to post
Share on other sites
4 hours ago, tluck said:

can you try this one? what is KP all about?

DSDT.zip

KP like this

Anonymous UUID:       2D6AEB3B-6313-385A-93E9-DF44519B0F33

Sun Sep  9 12:38:13 2018

*** Panic Report ***
panic(cpu 1 caller 0xffffff800838776f): Kernel trap at 0xffffff7f8aeec5d5, type 14=page fault, registers:
CR0: 0x000000008001003b, CR2: 0x0000000000000000, CR3: 0x000000000bce3000, CR4: 0x00000000000626e0
RAX: 0x0000000000500000, RBX: 0xffffff801979e0c0, RCX: 0xffffff801a9a4c80, RDX: 0xffffff801b87d480
RSP: 0xffffff91139b3eb0, RBP: 0xffffff91139b3eb0, RSI: 0x0000000000000000, RDI: 0x0000000000000000
R8:  0x0000000000000001, R9:  0x0000000000000030, R10: 0x0000000000000110, R11: 0x0000000000000008
R12: 0xffffff801a9a4cd0, R13: 0xffffff801b87d480, R14: 0xffffff801b87d480, R15: 0xffffff801a9a4c80
RFL: 0x0000000000010246, RIP: 0xffffff7f8aeec5d5, CS:  0x0000000000000008, SS:  0x0000000000000000
Fault CR2: 0x0000000000000000, Error code: 0x0000000000000000, Fault CPU: 0x1, PL: 0, VF: 1

Backtrace (CPU 1), Frame : Return Address
0xffffff91139b3980 : 0xffffff800826c1c6 
0xffffff91139b39d0 : 0xffffff8008395274 
0xffffff91139b3a10 : 0xffffff8008387544 
0xffffff91139b3a80 : 0xffffff800821e1e0 
0xffffff91139b3aa0 : 0xffffff800826bc3c 
0xffffff91139b3bd0 : 0xffffff800826b9fc 
0xffffff91139b3c30 : 0xffffff800838776f 
0xffffff91139b3da0 : 0xffffff800821e1e0 
0xffffff91139b3dc0 : 0xffffff7f8aeec5d5 
0xffffff91139b3eb0 : 0xffffff800886f6d5 
0xffffff91139b3f00 : 0xffffff80088723ab 
0xffffff91139b3f50 : 0xffffff80088740c6 
0xffffff91139b3fa0 : 0xffffff800821d557 
      Kernel Extensions in backtrace:
         org.rehabman.driver.AppleSmartBatteryManager(1.81.4)[E65767C3-A35F-348A-89CF-C6FAA44C5C6F]@0xffffff7f8aeeb000->0xffffff7f8aef3fff
            dependency: com.apple.iokit.IOACPIFamily(1.4)[95DA39BB-7C39-3742-A2E5-86C555E21D67]@0xffffff7f88ff2000

BSD process name corresponding to current thread: kernel_task
Boot args: slide=64 -no_compat_check -lilubetaall -alcbeta -v 

Mac OS version:
17G65

Kernel version:
Darwin Kernel Version 17.7.0: Thu Jun 21 22:53:14 PDT 2018; root:xnu-4570.71.2~1/RELEASE_X86_64
Kernel UUID: 1AE5ACFD-3B6F-3D74-AD52-31F1430DBC6F
Kernel slide:     0x0000000008000000
Kernel text base: 0xffffff8008200000
__HIB  text base: 0xffffff8008100000
System model name: MacBookPro8,1 (Mac-94245B3640C91C81)

System uptime in nanoseconds: 41034020254
last loaded kext at 40669556317: com.apple.driver.AppleHDA	281.52 (addr 0xffffff7f8a935000, size 958464)
loaded kexts:
com.paragon-software.lvm-for-mac	1
org.rehabman.voodoo.driver.PS2Mouse	1.8.34
org.rehabman.voodoo.driver.PS2Trackpad	1.8.34
org.rehabman.voodoo.driver.PS2Keyboard	1.8.34
VoodooSDHC	1.1d1
com.insanelymac.IntelMausiEthernet	2.3.0d0
com.rehabman.driver.ACPIPoller	0.8.1
org.rehabman.voodoo.driver.PS2Controller	1.8.34
org.hwsensors.driver.ACPISensors	1443
org.rehabman.driver.AppleSmartBatteryManager	1.81.4
org.hwsensors.driver.CPUSensors	1443
as.vit9696.AppleALC	1.3.1
org.netkas.driver.FakeSMC	1443
com.rehabman.driver.USBInjectAll	0.6.5
as.vit9696.WhateverGreen	1.2.2
science.firewolf.NightShiftUnlocker	2.2.1
as.vit9696.Lilu	1.2.7
com.apple.driver.AppleHDA	281.52
com.apple.driver.ApplePolicyControl	3.20.13
com.apple.driver.AppleUpstreamUserClient	3.6.5
com.apple.driver.AppleMCCSControl	1.5.5
com.apple.driver.AppleGraphicsDevicePolicy	3.20.13
com.apple.AGDCPluginDisplayMetrics	3.20.13
com.apple.driver.pmtelemetry	1
com.apple.iokit.IOUserEthernet	1.0.1
com.apple.iokit.IOBluetoothSerialManager	6.0.7f10
com.apple.Dont_Steal_Mac_OS_X	7.0.0
com.apple.driver.AppleHV	1
com.apple.driver.AppleOSXWatchdog	1
com.apple.driver.AppleLPC	3.1
com.apple.driver.ACPI_SMC_PlatformPlugin	1.0.0
com.apple.driver.AppleIntelSlowAdaptiveClocking	4.0.0
com.apple.driver.AppleSMCPDRC	1.0.0
com.apple.driver.AppleFIVRDriver	4.1.0
com.apple.driver.AppleIntelSNBGraphicsFB	10.0.4
com.apple.iokit.SCSITaskUserClient	404.30.2
com.apple.driver.AppleFileSystemDriver	3.0.1
com.apple.filesystems.apfs	748.51.0
com.apple.AppleFSCompression.AppleFSCompressionTypeDataless	1.0.0d1
com.apple.AppleFSCompression.AppleFSCompressionTypeZlib	1.0.0
com.apple.AppleSystemPolicy	1.0
com.apple.BootCache	40
com.apple.filesystems.hfs.kext	407.50.6
com.apple.driver.AirPort.Atheros40	700.74.5
com.apple.driver.AppleFWOHCI	5.5.9
com.apple.driver.AppleIntelHD3000Graphics	10.0.4
com.apple.driver.AppleAHCIPort	329.50.2
com.apple.driver.AppleBacklight	170.12.6
com.apple.driver.AppleRTC	2.0
com.apple.driver.AppleHPET	1.8
com.apple.driver.AppleACPIButtons	6.1
com.apple.driver.AppleSMBIOS	2.1
com.apple.driver.AppleACPIEC	6.1
com.apple.driver.AppleAPIC	1.7
com.apple.driver.AppleIntelCPUPowerManagementClient	220.50.1
com.apple.nke.applicationfirewall	183
com.apple.security.quarantine	3
com.apple.security.TMSafetyNet	8
com.apple.driver.AppleIntelCPUPowerManagement	220.50.1
com.apple.driver.DspFuncLib	281.52
com.apple.kext.OSvKernDSPLib	526
com.apple.driver.AppleGraphicsControl	3.20.13
com.apple.iokit.IOSurface	211.15
com.apple.iokit.IOAVBFamily	680.2
com.apple.plugin.IOgPTPPlugin	680.15
com.apple.iokit.IOEthernetAVBController	1.1.0
com.apple.driver.AppleSMBusController	1.0.18d1
com.apple.driver.AppleSSE	1.0
com.apple.driver.AppleSMBusPCI	1.0.14d1
com.apple.iokit.IOFireWireIP	2.2.9
com.apple.AppleGPUWrangler	3.20.13
com.apple.AppleGraphicsDeviceControl	3.20.13
com.apple.driver.AppleHDAController	281.52
com.apple.iokit.IOHDAFamily	281.52
com.apple.iokit.IOAudioFamily	206.5
com.apple.vecLib.kext	1.2.0
com.apple.driver.Apple16X50Serial	3.2
com.apple.iokit.IOSerialFamily	11
com.apple.driver.IOPlatformPluginLegacy	1.0.0
com.apple.iokit.IOSlowAdaptiveClockingFamily	1.0.0
com.apple.driver.IOPlatformPluginFamily	6.0.0d8
com.apple.iokit.BroadcomBluetoothHostControllerUSBTransport	6.0.7f10
com.apple.iokit.IOBluetoothHostControllerUSBTransport	6.0.7f10
com.apple.iokit.IOBluetoothHostControllerTransport	6.0.7f10
com.apple.iokit.IOBluetoothFamily	6.0.7f10
com.apple.driver.usb.cdc	5.0.0
com.apple.driver.usb.networking	5.0.0
com.apple.driver.usb.AppleUSBHostCompositeDevice	1.2
com.apple.driver.usb.AppleUSBHub	1.2
com.apple.iokit.IOSCSIMultimediaCommandsDevice	404.30.2
com.apple.iokit.IOBDStorageFamily	1.8
com.apple.iokit.IODVDStorageFamily	1.8
com.apple.iokit.IOCDStorageFamily	1.8
com.apple.driver.AppleXsanScheme	3
com.apple.iokit.IOAHCISerialATAPI	267.50.1
com.apple.iokit.IOAHCIBlockStorage	301.40.2
com.apple.filesystems.hfs.encodings.kext	1
com.apple.iokit.IO80211Family	1200.12.2
com.apple.driver.corecapture	1.0.4
com.apple.iokit.IOFireWireFamily	4.7.2
com.apple.driver.usb.AppleUSBEHCIPCI	1.2
com.apple.driver.usb.AppleUSBEHCI	1.2
com.apple.iokit.IOAHCIFamily	288
com.apple.driver.AppleEFINVRAM	2.1
com.apple.driver.usb.AppleUSBHostPacketFilter	1.0
com.apple.iokit.IOUSBFamily	900.4.1
com.apple.driver.AppleBacklightExpert	1.1.0
com.apple.iokit.IONDRVSupport	519.20
com.apple.iokit.IOGraphicsFamily	519.20
com.apple.driver.AppleEFIRuntime	2.1
com.apple.driver.AppleUSBHostMergeProperties	1.2
com.apple.iokit.IOSMBusFamily	1.1
com.apple.iokit.IOHIDFamily	2.0.0
com.apple.security.sandbox	300.0
com.apple.kext.AppleMatch	1.0.0d1
com.apple.driver.AppleFDEKeyStore	28.30
com.apple.driver.AppleEffaceableStorage	1.0
com.apple.driver.AppleKeyStore	2
com.apple.driver.AppleUSBTDM	439.70.3
com.apple.driver.AppleMobileFileIntegrity	1.0.5
com.apple.iokit.IOUSBMassStorageDriver	140.70.2
com.apple.iokit.IOSCSIBlockCommandsDevice	404.30.2
com.apple.iokit.IOSCSIArchitectureModelFamily	404.30.2
com.apple.driver.AppleCredentialManager	1.0
com.apple.driver.KernelRelayHost	1
com.apple.iokit.IOUSBHostFamily	1.2
com.apple.driver.usb.AppleUSBCommon	1.0
com.apple.driver.AppleBusPowerController	1.0
com.apple.driver.AppleSEPManager	1.0.1
com.apple.driver.IOSlaveProcessor	1
com.apple.driver.DiskImages	480.60.1
com.apple.iokit.IOStorageFamily	2.1
com.apple.iokit.IOReportFamily	31
com.apple.iokit.IOTimeSyncFamily	680.15
com.apple.iokit.IONetworkingFamily	3.4
com.apple.driver.AppleACPIPlatform	6.1
com.apple.driver.AppleSMC	3.1.9
com.apple.iokit.IOPCIFamily	2.9
com.apple.iokit.IOACPIFamily	1.4
com.apple.kec.Libm	1
com.apple.kec.pthread	1
com.apple.kec.corecrypto	1.0

EOF
Model: MacBookPro8,1, BootROM MBP81.004E.B00, 2 processors, Intel Core i5, 2.59 GHz, 8 GB, SMC 1.68f99
Graphics: Intel HD Graphics 3000, Intel HD Graphics 3000, Built-In
Memory Module: BANK 0/DIMM0, 4 GB, DDR3, 1333 MHz, Samsung, M471B5273DH0-CH9
Memory Module: BANK 0/DIMM1, 4 GB, DDR3, 1333 MHz, Samsung, M471B5273CH0-CH9
AirPort: spairport_wireless_card_type_airport_extreme (0x168C, 0x8F), Atheros 9287: 4.0.74.0-P2P
Bluetooth: Version 6.0.7f10, 3 services, 27 devices, 1 incoming serial ports
Network Service: Wi-Fi, AirPort, en1
PCI Card: Intel 82579LM PCI Express Gigabit Ethernet, Ethernet, PCI Slot 1638400
Serial ATA Device: HGST HTS725050A7E630, 500.11 GB
Serial ATA Device: Optiarc DVD RW AD-7710H
USB Device: USB 2.0 Bus
USB Device: Hub
USB Device: Integrated Camera
USB Device: Broadcom Bluetooth Device
USB Device: Biometric Coprocessor
USB Device: USB 2.0 Bus
USB Device: Hub
Thunderbolt Bus: 

It seem dsdt conflict with ACPIBatteryManager.kext

Share this post


Link to post
Share on other sites

Hello together,

 

last weekend I tried around 12h to boot up, always with the similar faults as shown on the picture, just the first message changes:

screenshot_42.png.f07a22d074a93a2763f76405e9fd0c53.png

 

What I did so far:

 

- use clover 4542 and 4509

- use my DSDT

- use DSDT from @tluck 

- use the package from tluck dated August, with my DSDT

- use bios default settings and make changes according to this guide

- save ACPI tables again and compared with my 1.52: same

 

Always the same result... argh.. The crazy thing is it was working before...

 

The only way to boot into macOS is without DSDT.. then of course nothing is working.

 

Somewhere else I read that macOS has sometimes problem with the installed RAM. So I will organize a few other modules and try again.

 

Keep you updated...

 

UPDATE:

Just tried DSDT_1.52_hs from @tluck , same result, see above picture.

 

UPDATE 2:

new RAM, same problem

Edited by SnuK
another test

Share this post


Link to post
Share on other sites
36 minutes ago, SnuK said:

Hello together,

 

last weekend I tried around 12h to boot up, always with the similar faults as shown on the picture, just the first message changes:

screenshot_42.png.f07a22d074a93a2763f76405e9fd0c53.png

 

What I did so far:

 

- use clover 4542 and 4509

- use my DSDT

- use DSDT from @tluck 

- use the package from tluck dated August, with my DSDT

- use bios default settings and make changes according to this guide

- save ACPI tables again and compared with my 1.52: same

 

Always the same result... argh.. The crazy thing is it was working before...

 

The only way to boot into macOS is without DSDT.. then of course nothing is working.

 

Somewhere else I read that macOS has sometimes problem with the installed RAM. So I will organize a few other modules and try again.

 

Keep you updated...

 

UPDATE:

Just tried DSDT_1.52_hs from @tluck , same result, see above picture.

 

did you set a serial number by any chance? if yes try to boot with it removed

Edited by n0xius
more info

Share this post


Link to post
Share on other sites

Hmm. can you try with the DSDT most recently provided and this config.plist which will disable all the Clover DSDT edits except fix regions.

rename it config.plist or select during Clover startup. note: i forget to mention - this most recent DSDT needs ACPIPoller.kext to handle FAN speed.

Obviously this DSDT works for me.

@Snuk i took your nicely patched DSDT.dsl and added a few more changes/fixes. then compiled it.

 

 

config.1600x900.2e3.plist

Edited by tluck

Share this post


Link to post
Share on other sites

The Mojave config, used in High Sierra, with the graphics tweak for 1600 x 900 display is working fantastic for me. I've also upgraded RAM to 16GB and graphics glitches are pretty much a thing of the past.

Share this post


Link to post
Share on other sites
22 hours ago, n0xius said:

did you set a serial number by any chance? if yes try to boot with it removed

 

Do you mean the serial number inside the config.plist?

Share this post


Link to post
Share on other sites

Hello again,

 

today I made some more tests, here are the results:

 

- put in another RAM, same problem as described 9/11/2018 at 8:31 PM

- boot with my dsdt_1.52 and the config from @tluck actual bundle,  same problem as described 9/11/2018 at 8:31 PM

- boot with my dsdt_1.52 and tlucks new config config.1600x900.2e3.plist, kernel panic (see attached picture, related to AppleIntelCPUPowerManagement, maybe same problem as @SuperReaper reported)

- boot with tlucks dsdt_1.52 and the config from @tluck actual bundle,  same problem as described 9/11/2018 at 8:31 PM

- boot with tlucks dsdt_1.52 and tlucks new config config.1600x900.2e3.plist, successfully boot into macOS HS, looks good

- boot with tlucks dsdt_1.52_hs and the config from @tluck actual bundle, kernel panic (see attached picture, related to AppleIntelCPUPowerManagement, maybe same problem as @SuperReaper reported)

- boot with tlucks dsdt_1.52_hs and tlucks new config config.1600x900.2e3.plist, kernel panic (see attached picture, related to AppleSmartBatteryManager, maybe same problem as @SuperReaper reported as well)

 

So again, for me the following is working: tlucks dsdt_1.52 and tlucks new config config.1600x900.2e3.plist!

 

 

P.S. sorry for the bad pictures, they are captured from slo-mo videos

dsdt_1.52 and tlucks new config config.1600x900.2e3.plist

tlucks dsdt_1.52_hs and tlucks new config config.1600x900.2e3.plist

Edited by SnuK
typo

Share this post


Link to post
Share on other sites
4 hours ago, SnuK said:

Hello again,

today I made some more tests, here are the results:

...

So again, for me the following is working: tlucks dsdt_1.52 and tlucks new config config.1600x900.2e3.plist!

 

Great news. That points to the recent version of Clover breaking the DSDT for some reason (and not for everyone!?) ... as this "working" config.1600x900.2e3.plist has the ACPI DSDT fixes turned off except Fix_regions. But everything is already in the pre-made DSDT except a few things. I will make a few appropriate changes and repost the zip.

 

Note: i found very little difference between the 1.46 DSDT and 1.52 DSDT.

 

Share this post


Link to post
Share on other sites
10 hours ago, maihoward1985 said:

Hey guys. I would ask you how to "whitelist" my T420 Bios. I got this machine with Bios 1.49 and I don't know where to do it.

 

Hi, it's not a question of where but how to do it.

You need to flash a bios with whitelist mod, for example v1.52 with whitelist mod: T420 BIOS v1.52 mod

 

Use it on your own risk, the T420 here already had this bios.

Edited by SnuK

Share this post


Link to post
Share on other sites
On 9/13/2018 at 6:06 AM, SnuK said:

 

Hi, it's not a question of where but how to do it.

You need to flash a bios with whitelist mod, for example v1.52 with whitelist mod: T420 BIOS v1.52 mod

 

Use it on your own risk, the T420 here already had this bios.

 

Thank you Snuk. I will do it.

Share this post


Link to post
Share on other sites

@Tluck, @Snuk,


How to resolve this problem without remove USB Inject All Kext while using Config Mojave?. I am too curious how exactly Mac OS Mojave looked like to that I've decided to give my computer a try by using Mojave Config in Tluck Package. After boot, the MacOS High Sierra recognize my system as MacBook Pro 2013 and also allow me upgrade direct via Apple Store. 

Besides that, something really strange happened. I can't open Config Mojave Plist file by Clover then I've tried several times before using Plist Edit Pro to check what wrong with it. When Plist Edit Pro opened the config file, there few main information inside has been deleted ( Kext to Patch ... System ... etc )
  

 

IMG_1621.thumb.jpg.8b66e9c8249a99cdeb8eeb711b630898.jpg

Share this post


Link to post
Share on other sites
42 minutes ago, maihoward1985 said:

@Tluck, @Snuk,


How to resolve this problem without remove USB Inject All Kext while using Config Mojave?. I am too curious how exactly Mac OS Mojave looked like to that I've decided to give my computer a try by using Mojave Config in Tluck Package. After boot, the MacOS High Sierra recognize my system as MacBook Pro 2013 and also allow me upgrade direct via Apple Store. 

 

Are you saying that if mojave.plist is used, then it's possible to update to mojave via Apple Store?

 

I use mojave.plist on a High Sierra install and get the same USB Accessory Needs Power if more than one USB device is plugged in.

Edited by bedfellow

Share this post


Link to post
Share on other sites

@bedfellow Yes. When my machine was identified as Macbook Pro 13, it’s allowed me to update like this way. ( But make sure you already install apple beta or developers profile into your system ). 

 

I used same config, same packages i have downloaded from Tluck but i dont know why only X220 was recognized as Macbook Pro 2013. My “new” T420 wasn’t.

2B8AEF63-FA64-47CC-95E8-57BEF658196F.jpeg

Edited by maihoward1985

Share this post


Link to post
Share on other sites
53 minutes ago, maihoward1985 said:

@bedfellow Yes. When my machine was identified as Macbook Pro 13, it’s allowed me to update like this way. ( But make sure you already install apple beta or developers profile into your system ). 

 

I used same config, same packages i have downloaded from Tluck but i dont know why only X220 was recognized as Macbook Pro 2013. My “new” T420 wasn’t.

 

It allows you to update, but did you perform the update?

 

My T420 identifies as MacBook Pro (Retina, 13-Inch, Late 2013)

Share this post


Link to post
Share on other sites
1 hour ago, bedfellow said:

 

It allows you to update, but did you perform the update?

 

My T420 identifies as MacBook Pro (Retina, 13-Inch, Late 2013)


Yes. I did. While I was writing reply comments here, my machine was updating by that way. Here is my very first impressions since I was able to update by this way. 

- Trackpad, Wifi, Speaker ... etc. Still recognized like Native machine. I don't see any problems. 
- Still able to keep some patched I had used like Night Shift .... 
- Due to HD3000 is non-metal supporting, there have major lagging. I hope Tluck or anyone else could find away to patch frame or something like this to make the system run more smoothly. 
- Tluck config Mojave is so amazing !!!!


 

 

35FFB5EA-DFEC-45DA-A613-E58C1E84DF0D.jpeg

Edited by maihoward1985

Share this post


Link to post
Share on other sites
26 minutes ago, bedfellow said:

I performed the update and now in Mojave, but have lost wifi. Any advice on getting it working?

 


Which brand of Wifi card do you use in your machine?. 

I use Broadcom and I also have to put bunch of patches into my config's kexts-to-patch in order to make it work in MacOS.  
Here is what I have collected for a long time since El Cap til now.

wifi.plist


Hopefully it will help you. I have no knowledge about coding so that I have copy-paste and then messing my machine until I see which works for me lol.
Besides that, how do your machine graphics work? any lag? 
 

Edited by maihoward1985

Share this post


Link to post
Share on other sites
7 hours ago, bedfellow said:

I performed the update and now in Mojave, but have lost wifi. Any advice on getting it working?

 

If you have Atheros, bad news: Apple removed the support in Mojave completely.

But you can use the kext of HighSierra, see also here.

 

 

Share this post


Link to post
Share on other sites
1 hour ago, SnuK said:

If you have Atheros, bad news: Apple removed the support in Mojave completely.

But you can use the kext of HighSierra, see also here.

 

Thanks for the link but unfortunately I don't understand what I need to do. Is there a kext I need to put somewhere?

Share this post


Link to post
Share on other sites

I had tried copying over High Sierra IO80211Family.kext, but that didn't work, even after several reboots, so thought I would give an external USB wifi dongle a try whilst trying to work out how to get the internal card working.

 

The USB dongle didn't work so I went searching for drivers for that and discovered https://github.com/chris1111/WIFI-Network-macOS-High-Sierra, which I installed. On reboot I had wifi, so assumed it was the dongle, but surprisingly it is actually the built in wifi card. Not sure if it's c combination of both the kext and driver, or whether just the driver.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By ludufre
      Installing macOS Mojave on Lenovo ThinkPad L440

       
      There are two version of this laptop:
      - 20AS = Chipset QM87, without Express Card (mine).
      - 20AT = Chipset HM86, with Express Card.
      I strong believe is the same thing...
       

      Changelog:
       
      01/20/2019 11:49h GMT-0
      - First version.
       
      What works and what does not
       
      - Processor: Intel Core i5-4300M ->  Work. All SpeedStep stages.
      - Video Card: Intel HD4600 ->  Work. QE/CI and Metal.
      - Chipset: Intel QM87 ->  Work.
      - Mini DisplayPort ->  Work. But no audio, yet.
      - VGA ->  Not work. Normal.
      - Audio: ALC292 ->  Work.
      - WiFi/Bluetooth: Intel AC 7260 ->  Not work. Replaced with DW1560 (need whitelist removal).
      - Ethernet: Intel I217-LM ->  Work.
      - Card Reader: Realtek RTS5227 ->  Not work.
      - Keyboard and Touchpad ->  Work.
      - Webcam ->  Work.
      - Fingerprint Reader ->  Not work. Normal.
      - USB3.0 ->  Work.
      - Sleep ->  Work.
      - Airdrop, Handoff, Instant Hotspot and Continuity ->  Work after replaced wireless.
       
       
      Extras
       
      - FullHD 1920x1080 display upgrade: 
      Replaced with AU Optronics B140HAN01.1 30pin eDP (B140HAN01.2 and B140HAN01.3 also compatible)
      Apparently same screen as Dell Latitude E6440, E7440, Lenovo Ideapad U430 and E129.
       

      Todo
       
      - Make DP audio work.
      - Make Card Reader work.
      - Upgrade CPU to i7-4712MQ (Ordered. It's on the way)
      - Replace touchpad with T460 model (Ordered. It's on the way)
      - Sierra Gobi5000 4G LTE modem EM7355 (Ordered. It's on the way. I hope works. )
      - Upgrade to 16GB RAM
       
       
      What you need to install

      - Running install of macOS
      - One USB flash drive of 8GB or bigger
      - macOS Mojave install app
      - Clover EFI
      - Clover Configurator
      - Some KEXTs and SSDT patches


      How create create the install flash drive
       
      Prepare install flash drive

      Format the flash drive with GUID partition mapping and name it "Install".

      - Open Disk Utility.
      - Click in View, then "Show All Devices".
      - Select the destination flash drive, then Erase.
      - Name: Install, Format: Mac OS Extended (Journaled) and Scheme: GUID Partition Map
       
      Create install flash drive

      Open terminal and run this command:
      sudo /Applications/Install\ macOS\ .app/Contents/Resources/createinstallmedia --volume /Volumes/Install --nointeraction This will take about 30 minutes.
       


      Install bootloader

      Download the RehabMan's CloverEFI fork (used 4701) and install with this options on "Install macOS Mojave":
       
      - Install for UEFI booting only
      - Install Clover in the ESP
      - UEFI Drivers - ApfsDriverLoader-64
      - UEFI Drivers - AptioMemoryFix64

      aaa  
       
       
      Make things works

      Will be created a partition named EFI and mounted in Desktop.
      - Replace the /Volumes/EFI/CLOVER/config.plist with mine attached below
                    If you have modded BIOS with Advanced Menu and enabled 128MB DRAM-prealloc use 128MB_DRAM-prealloc_config.plist.zip
                    If no, then use 32MB_DRAM-prealloc_config.plist.zip
      - Put SSDT_L440.aml attached below in /Volumes/EFI/CLOVER/ACPI/patched/
       
      Generate your Serial, MLB and SmUUID
       
      - Open the replaced config.plist with Clover Configurator (used 5.3.2.0)
      - Go to SMBIOS, click few times in "Generate New" in Serial Number and SmUUID.
       
      Download those Kexts and put in /EFI/CLOVER/kexts/Other/
       
      - Download the FakeSMC.kext from here. I used the version 2018-0915.
      - Download the VoodooPS2Controller.kext from here. I used version 2018-1008.
      - Download the IntelMausiEthernet.kext from here. I used the version 2018-1031.
      - Download the Lilu.kext from here. I used the version 1.3.1.
      - Download the AppleALC.kext from here. I used the version 1.3.4.
      - Download the WhateverGreen.kext from here. I used the version 1.2.6.
      - Download the AppleBacklightFixup.kext from here. I used the version 2018-1013.
      - Download the USBInjectAll.kext from here. I used the version 2018-1108.
      - Download the ACPIBatteryManager.kext from here. I used the version 2018-1005.
       
       
      Wifi and Bluetooth (DW1560 / BCM94352Z)
       
      Unfortunately, some notebook manufacturers are currently blocking the replacement of wireless cards. They want you to only use the models sold by them. And of course, none of them from Lenovo for this notebook model is compatible with MacOS.
       
      If you try to start with an unauthorized wifi card for them, you will receive a screen error:
      1802: Unauthorized network card is plugged in - Power off and remove the network card. Since this check is done directly in the BIOS, the only solution is to modify it.
      But since nothing is easy in this life, there is one small big problem:
      - The BIOS update procedure does not allow you to use modded files as it used to be.
      - You will need to physically reach your BIOS on the motherboard and make use of a USB BIOS reader/writer.
       
      So what you need to do:
      1. Disassembly your laptop;
      2. Dump your BIOS with an USB BIOS reader with SOIC8 clip (to not desolder from the motherboard);
      3. Patch it (In addition to removing the whitelist, add the advanced menu);
      4. Fix RSA signature;
      5. Reflash BIOS;
      6. Replace wireless card;
      7. Remount your laptop;
      8. Done.
       
      Soon, I'll provide step by step in this process. Probably until end of this week.
      In the meantime, if you need to, send me your dump that I do steps 3 and 4 for you.
      I also add the Advanced Menu so you can increase to 128MB the DRAM-prealloc.
       
      After replaced the wireless card. Download those Kexts and put in /EFI/CLOVER/kexts/Other/
       
      - Download the AirportBrcmFixup.kext from here. I used the version 1.1.9.
      - Download the BrcmFirmwareRepo.kext and BrcmPatchRAM2.kext from here. I used the version 2018-0505.
      - Download the BT4LEContinuityFixup.kext from here. I used the version 1.1.2.
       
       
      Now you can start the instalation without problem (I guess).
       
       
      How install
       
      UEFI Setup Configuration and Installation

      UEFI configuration
       
      My BIOS is the latest: 1.93 (J4ET93WW) 

      - Shutdown and insert the flash drive.
      - Power on with F1 pressed to enter BIOS setup.
      - Change value: Config - Intel(R) AMT - Intel(R) AMT Control to DISABLED
      - Change value: Security - Security Chip to DISABLED
      - Change value: Security - Anti-Theft - Intel(R) AT Module Activation to DISABLED
      - Change value: Security - Anti-Theft - Computrace to DISABLED
      - Change value: Security - Secure Boot to DISABLED
      - Change value: Startup - UEFI/Legacy Boot to BOTH, Legacy First and CSM Support = Yes
      - Save & Exit Setup (F10)
       
      - Now, hold the F12
      - In the list, select your flash drive.
       
      The installer will start. 
      
      Format destination disk

      Format the disk with GUID partition mapping and name it "Macintosh".

      - Select Disk Utility in the list, then press Continue.
      - Click in View, then "Show All Devices".
      - Select the destination Disk, then Erase.
      - Name: HD, Format: APFS and Scheme: GUID Partition Map

      Close Disk Utility.
      
      Select "Install macOS", then Continue.
      Follow instructions in screen.

      After install

      After first part install the system will reboot. Maybe you have to press F12 again and select the flash drive.
      
      The second part of the installation will begin. This will take 16 minutes.
       

      Post installation

      Install bootloader
       
      When the second part of install finish, the system will reboot again.

      After performing the user initial setup and go to the desktop, you need to install Clover on internal disk.

      Open the Clover installer inside flash drive that you copied before.

      Use same options above but choose the system partition this time.

      Now you need to replace the config.plist inside your destination disk EFI parittion with config.plist inside flash card EFI partition.

      The flash drive EFI partition is unmounted. Mount with terminal "sudo diskutil mount /dev/rdiskXs1". To know what X is, use "diskutil list", most likely is 1.
       
      Last step
       
      Copy all Kexts from flash drive to /Library/Extensions, with those commands in Terminal:
      sudo cp -R /Volumes/EFI/EFI/CLOVER/kexts/Other/* /Library/Extensions/ sudo chmod -R 755 /Library/Extensions sudo chown -R root:wheel /Library/Extensions sudo kextcache -i / Restart the system.
       
       
      It's done!

       
      And last but not least
       
      I would like to thank the following community members, by making these dream possible:
      @crushers, @snatch, @apianti, @blackosx, @blusseau, @dmazar, @slice2009, @autumnrain, @phpdev32, @EMlyDinEsH, @RehabMan, @Scellow, @mitch_de, @Shailua, @Andy Vandijck, @maxfierke, @ArturXXX, @LexHimself, @brumas, @Shiki and all others members involved directly or indirectly.
       
      SSDT-L440.aml
       
       
      32MB_DRAM-prealloc_config.plist.zip
      128MB_DRAM-prealloc_config.plist.zip
    • By tluck
      Lenovo T460 macOS with Clover Guide
      Latest Release on GitHub Updated to Clover r4849 Updated Kexts Shift to use WhatEvergreen.kext SSDT updates for T460 Added Frank's T470p DSDT files Added T470 DSDT
        Various Tweaks over Last months The zip file is a complete Clover ESP (/EFI) bundle and kext pack for the Lenovo T460. The current file bundle is tested on Sierra. 
      Note: I never got the GFX fully working on El Capitan. 
      Full Clover file set - config.plist etc. Includes all custom kexts Includes custom DSDT/SSDT scripts and patches Utility scripts The zip bundles are posted to GitHub: https://github.com/tluck/Lenovo-T460-Clover/releases
      Caveat: The T460 systems used here was configured with: i5-6300U, Intel HD Graphics 520, 1920x1080 touch screen. If you have a different system model, then extract the ACPI files and use the included scripts to create a set of files consistent with your system type and BIOS version. See below for details.
      Credits: RehabMan, Shmilee, vusun123, TimeWalker, Mieze from which, much of their work and help is/was was used to get the T460 to this point.
      Devices and aspects working:
      Ethernet -  Intel I219LM is enabled via IntelMausiEthernext.kext WiFi/BT - substitute the Intel WiFi/BT with a compatible Broadcom or Atheros chip Audio - ALC293 codec implemented via AppleALC.kext (old AppleHDA_ALC293 and CodecCommander kexts are not needed) PS2 - ClickPad + TrackPoint + all 3 buttons - using a modified VoodooPS2Controller to support new layouts - and added some custom Fn key maps based on 440/450 dsdt USB - implemented via custom SSDT + USBInjectAll kext. All USB3/USB2 ports are intel-based and work -  3 external USB and internal Camera, BT, etc  Sleep/Wake - the sleepwatcher package and custom sleep/wake scripts are used to help with sleep/wake for BT and PS2 devices. Note: have not tried to implement the SD card reader - no driver found.
      ACPI Files
      New Installation - Steps and Details
      Part 1 - OS Installation
      Part 2- Post OS Installation and Setup
      Notes on Custom Kexts
       
    • By Abhiabhash
      I have a lenovo laptop with pentium 2020M 2.4ghz with 4gb ddr3 ram intel graphics and 500gb wd hdd i wanted to install hackintosh on my pentium for editing purposes beacuse windows sucks so can you please tell me how can i install it and which version should i install
    • By gengik84
      Ciro82==>>Thanks
      Uno dei tre Requisiti:
      Hack funzionante Mac vero Macchina virtuale Impostazioni Bios per il boot:
      Cercate una voce  del tipo “Sata Mode”e settatela  in AHCI
      Secure Boot: disabilitare o altri sistemi operativi
      CSM: UEFI o LEGACY, oppure a secondo del tipo di installazione
      VT-x / VT-d disable
      *Nota: Secure boot e csm valido solo per bios UEFI
      Materiale Occorrente 
      "OS X (Versione App.Store)”
      USB 8GB  *nota: nel caso di usb superiori dovrà essere partizionata, in modo da avere una partizione su cui "lavoreremo,di questa dimensione
      ShowAllfiles 
      kext Wizard 
      Bootloader Clover_2.3k_r xxx:                   http: //sourceforge.n.../cloverefiboot/
      Clover Configurator:                                    http: //mackie100proj...a.org/download/
      FakeSmc.kext:                                            https://github.com/kozlek/HWSensors/releases
      In allegato,a fondo pagina troverete un "pacchetto" contenente : ShowAllfiles, Kext Wizard, FakeSmc.kext: 
      App alternative:
      ESP Mounter Pro: per montare la partizione EFI
      Vi illustrerò tre metodi per creare la usb, ma sono ben distinti… quindi usatene soltanto uno
      Metodo 1: “Install Mac_OS_X.command” Metodo 2: “Create Install Media di Apple” Metodo 3:  Metodo Manuale Alla fine delle preparazione dell’installer, tutti i metodi necessitano l’installazione del Bootloader Clover sulla a vostra USB.
      “CONDIZIONI OBBLIGATORIE”
      PUNTO 1: che la vostra usb sia stata preventivamente nominata USB (caratteri maiuscoli) Tabella di partizione GUID e la formattazione in  Mac esteso Journaled.
      PUNTO 2: che l’installer di OSX si trovi in Applicazioni
      Utility Disco 
      Selezionate la pendrive, andate su “partizione”, selezionate “1 partizione”, impostate Mac OS esteso journaled e date il nome USB, poi in basso cliccate su opzioni e scegliete Tabella partizione (GUID), poi “applica”.
      Immagine 
      Riporto nuovamente l’operazione sopra citata adoperando dal nuovo Utility Disco introdotto su El Capitan.
      Rimane ovviamente invariato nome della usb in ==>> USB (maiuscolo), la formattazione in Mac esteso Journaled e sia la mappa partizione in GUID
      Da utility disco selezionate la usb, cliccate su inizializza.
      dal menù a tendina scegliete la relative impostazioni
      Immagine  
      Procedura effettua da High Sierra è la stessa della precedente, l'unica attenzione e operazione da aggiungere in primis  è cliccare nel menù a tendina in alto sulla sinistra di utility disco e selezionare "mostra tutti i dispositivi"
      Immagine 
       
      =====================
        METODO 1: "Install_Mac_OS_X.Command" Lo script che trovate allegato in fondo alla guida permette la creazione dell’installer in maniera automatica
      Include la possibilità di scelta di tre versioni di osx
      Yosemite El Capitan Sierra Il risultato finale è come quello del metodo "manuale" descritto nella guida, per cui l'installazione avverrà in un solo passaggio, non in due come con il metodo createinstallmedia. 
      Offre inoltre la possibilità di inserire un kernel patchato, utile, per esempio, per chi usa AMD.
      Rimane invariato il nome dato alla usb in USB, mappa partizione e tipo di formattazione
      Se la vostra usb non sarà rinominata nel modo corretto, verrete avvisati dal terminale, quindi non dovrete far altro che apportare la relativa modifica e rilanciare nuovamente lo script
      Esempio
      ===========================
      Metodo 2 
      L'intento è quello di usare la procedura fornitaci direttamente da Apple, "createinstallmedia", introdotta  con Mavericks. 
      Tale metodo prevede l’uso del terminale che via via se ne sta perdendo il “valore e l’uso”
      Inizialmente per i neofiti potrà sembrare problematico ma alla fine non è così.
      Durante il post installazione alcune operazioni ne richiedono l’ uso.
      Perciò mi sono chiesto perchè, qualora uno volesse, non far conoscere da subito un po’ questo “strumento”???
      Per favorirvi vi ho allegato i comandi già  “pronti”, i quali li potrete copiare ed incollare sul terminale.
      A questo punto aprite il terminale, copiate ed incollate il comando sottostante e premete invio, digitate la vostra password e premete nuovamente invio.
      Comando per creare USB con Yosemite:
      sudo /Applications/Install\ OS\ X\ Yosemite.app/Contents/Resources/createinstallmedia --volume /Volumes/USB --applicationpath /Applications/Install\ OS\ X\ Yosemite.app --nointeraction  
      Comando per creare USB con El Capitan
      sudo /Applications/Install\ OS\ X\ El\ Capitan.app/Contents/Resources/createinstallmedia --volume /Volumes/USB --applicationpath /Applications/Install\ OS\ X\ El\ Capitan.app --nointeraction Comando per creare USB con Sierra 
      sudo /Applications/Install\ macOS\ Sierra.app/Contents/Resources/createinstallmedia --volume /Volumes/USB --applicationpath /Applications/Install\ macOS\ Sierra.app/ --nointeraction Per creare USB con Hight Sierra o Mojave usate --> C_I_M (aggiornato per 10.14)
       
      Funziona con il drag & drop sul terminale, in questo caso non vi è necessità che la usb sia nominata in un determinato modo ed essendo basato su create install media ovviamente funziona da 10.9 a 10.14.... 
      BENE…IL PROCESSO DI CREAZIONE E’ INIZIATO…
      AVREMO CIRCA 20/30 MINUTI DI TEMPO LIBERO A CUI DEDICARSI A CIO’ CHE VOGLIAMO………………………………………..  
      COLGO L’OCCASIONE PER FARVI NOTARE LA VELOCITA’ E LA SICUREZZA DI QUESTO METODO
      CONFRONTATE QUESTO CON IL TERZO METODO E NOTERETE CHE CON UN SOLO PASSAGGIO, OSSIA IL COMANDO DATO AL TERMINALE, FACCIAMO IN UNA SINGOLA OPERAZIONE TUTTI I VARI STEP DESCRITTI SULL’ ALTRO METODO.
      DETTO QUESTO, MOLTO IMPORTANTE E’ SOTTOLINEARE CHE COSI’ FACENDO EVITEREMO ERRORI  DI DISTRAZIONE RIGUARDO AI PASSAGGI O FRAINTENDIMENTI.
      Immagine 
      Potete adesso passare ad installare il bootloader Clover sulla vostra usb.
      *NOTA*:
      Avendo usato questo metodo l'installazione si dividerà in due fasi, perciò dopo il primo riavvio e necessario far partire nuovamente l'installer, selezionare lo stesso disco senza formattarlo.
      Finita questa ulteriore fase , l'installazione sarà terminata
      =========================
      METODO "MANUALE"....  (lascio per futura memoria-Compatibile fino a 10.12)
      ==========================
      Bootloader
      **Nota:** Installazione in UEFI  dipenderà dalla scheda madre in vostro possesso, quindi se non supporta tale opzione , il bootloader dovrà essere installato in  modalità Legacy.
       Vi invito, qualora non sapeste questa informazione, a recarvi nel sito ufficiale del produttore e controllare le informazioni a riguardo
      Fatto questo dobbiamo installare  Clover sulla usb.
      A seconda del tipo di Bios o al tipo di installazione che vogliamo fare UEFI o Legacy avremo ovviamente configurazioni diverse in questa fase.
      Lanciate il pkg.
      Immagine 

       
      Cambiate la destinazione di installazione ad USB oppure Install Mac_OS_X (a secondo del tipo di creazione eseguita)
      Successivamente clicchiamo su "Ad Hoc"
      Per Installazione UEFI
      Mettete i flag   : Installazione solo per avvio UEFI
                               : installare Clover nella ESP
                               : Driver64UEFI  AptioMemory --> (consigliato) 
                               : Driver64UEFI  ApfsDriverLoader --> (consigliato) --> sostituisce l'uso del driver apfs.efi
                               : Selezionate l'altri driver come da successiva immagine,
       
      *Nota: Altri driver che si possono usare  al suo posto  sono:
       informazioni 
       
      Proseguite con l’installazione.
      Immagine 
      ** Ricordate che avrete accesso a questa cartella dopo aver montato la partizione EFI**
      ===========================
      Per installazione Legacy
      Immagine 
      ===========================
      Impostazione per config.plist:
      Con clover configurator “montate” la partizione EFI della usb.
      1) Per fare questo nel menù di sinistra, cliccate su “Mount EFI”
      2) individuate la partizione relativa alla vostra usb, a questo punto montiamo la relativa partizione EFI  selezionando l’apposito pulsante “Mount Partition”
      Immagine 
      3) Successivamente cliccate su “Open Partition”.. recatevi in EFI/Clover ed aprite il config.plist
      4) Sezione ACPI: Disabilitate tutti i fix sia del menù 1 che del menù 2
      Immagine 
      5) Sezione BOOT: Sole se si sta installando Yosemite mettete il flag su kext-dev-mode=1
      Immagine 
      6) Sezione RT Variables: Se si sta installando El Capitan oppure Sierra, aggiungere i valori: BooterConfig= 0x28, CsrActiveConfig= 0x67
      Immagine 
      7) Sezione System Parameters: Su inject kext mettete YES
      Immagine 
      ===========================
      Nota: Su El Capitan, è stato introdotto SIP (System Integrity Protection)
      Info:
      ===========================
      Recatevi in EFI/Clover/kext/10.x 
      X= alla versione di osx che state installando. Per esempio se installerete Yosemite dovrete recarvi nella cartella 10.10, con El Capitan in 10.11….ecc
      Se non ci fosse tale cartella, createla e nominatela voi a “modo”.
      Copiatevi all’interno FakeSmc.kext
      *Nota se venite già da altre vostre configurazioni, oltre kext sopra citato ,potete mettere gli altri necessari per il vostro hardware
      Stessa cosa se avete DSDT e/o SSDT potete copiarli in EFI/Clover/Acpi/Patched
      Immagine 
      
      Per High Sierra:
      Scaricare il driver apfs.efi a fine guida, collocarlo:
          --> EFI/clover/Driver64UEFI se stiamo usando UEFI
      --> EFI/Clover/Driver64 se stiamo usando Legacy
       
      Per chi volesse continuare ad usare HFS vi rimando a questo post:
        Come installare High Sierra in HFS direttamente dalla usb  
      Utenti Laptop:  Nel 99% è obbligatorio disattivare la grafica discreta Nvidia/Amd per installare questo nuovo osx
                                     Quindi aggiungete --> SSDT-Disable_DGPU.aml.zip
                                     in EFI/Clover/acpi/Patched della usb
      --------------------------------------------------------------------
      Per Mojave:
      Scaricare il driver apfs.efi per 10.14 a fine guida, collocarlo:
          --> EFI/clover/Driver64UEFI se stiamo usando UEFI
      --> EFI/Clover/Driver64 se stiamo usando Legacy
      Versione di clover non antecedente a V_4015
      Volete usare HFS?
      E' possibile fare un installazione diretta su altro disco o partizione, nel caso può essere usato anche per effettuare aggiornamenti...
      nel caso guardate...
       Mojave in HFS 
       Oppure direttamente da usb  
       
      Fatto questo avrete la vostra USB bootable per installare OSX.
      ………Non scordatevi Fakesmc.kext da mettere nella relativa cartella…. senza il quale non farete mai il Boot......
      *NOTA: se usato il terminale per la creazione della usb, l'installazione si dividerà in due fasi, perciò dopo il primo riavvio e necessario far partire nuovamente l'installer, selezionare lo stesso disco senza formattarlo.
      Finita questa ulteriore fase , l'installazione sarà terminata
      **NOTA** Se avete processori Broadwell,Skylake o Kabylake...usate FakeSmc.kext e relativi sensors che trovate all'interno del secondo pacchetto.. (potete usarlo anche sui precedenti senza problemi, essendo una versione più aggiornata ha ulteriore supporto per le cpu più recenti)
      Update: Fakesmc e sensors versione 6.26
      Post installazione... post #2           
       Buon Hack….. 
      Aggiornamento:Install_Mac_OS_X.command.zip (compatibile da 10.10 a 10.12)
      le info le trovate a questo post
      Ringrazio @Ciro82 che mi ha aiutato nel preparare questa guida.
      Pacchetto.zip
      Pacchetto-2.zip
      apfs.efi-10.13-NoLog.zip
      Pacchetto-Fake+Sensors 6.26.1440.zip
      apfs.efi-10.13.1-No_LOG.zip
      apfs.efi-10.13.2_No_Log.zip
      apfs.efi-10.13.3-No_Log.zip
      apfs.efi-10.13.4-No_Log.zip
      apfs.efi-10.13.5_No_Log.zip
      C_I_M.zip
       
      apfs.efi-10.14-beta1_No_Log.zip






×