Jump to content
ErmaC

Clover General discussion

20,681 posts in this topic

Recommended Posts

 

On 11/6/2019 at 7:43 PM, Pene said:

A friend is trying to install macOS with Clover, from a USB stick made by createinstallmedia, and 2 minutes before the end of first phase of install, he is getting the error:

"An error occurred validating the installer data. The download is either damaged or incomplete. Redownload the installer and try again."

He tried with both Mojave and Catalina USB installers (created with createinstallmedia from his Macbook), and he also tried with two different USB sticks, and the same error persists in all cases. 

 

On 11/7/2019 at 11:38 AM, Slice said:

I had similar error resolved by boot with legacy Clover. Wow! It works! I didn't understand what is happen. May be some variable in NVRAM is a culprit.

Another time I installed Mojave and got a message "The installer is broken and can't be used". The solution is set data to half year ago. That's fine! 

 

Following this problem, I have narrowed it down to the rank of DIMMs used.

This error appears during install when he is trying to install with Single-Rank DIMMs (2x8GB).

The error does not appear, and he can install successfully, when trying to install with Dual-Rank DIMMs (also 2x8GB).

 

The memory rank information appears in SMBIOS, at Type17->Attributes (0Bh), maybe it needs to be taken into consideration for something? (currently we are not doing anything with it within Clover)

It still baffles me though how it can affect the installer to give this error. Also, if the Single-Rank DIMMs are put back after macOS is already installed, everything seems to be functioning properly.

Edited by Pene

Share this post


Link to post
Share on other sites
Advertisement
2 minutes ago, Andres ZeroCross said:

I don't know what should i check in mDNSResponder.plist.

It is a functionality of the Bonjur service that cause a problem of waking on wifi and LAN. Your is a different problem.

Share this post


Link to post
Share on other sites
1 minute ago, vector sigma said:

It is a functionality of the Bonjur service that cause a problem of waking on wifi and LAN. Your is a different problem.


So untick "Wake for network access" and "enable Power Nap" should be the solution??? I have unticked these options in Energy Saver preferences

Share this post


Link to post
Share on other sites
32 minutes ago, Andres ZeroCross said:


So untick "Wake for network access" and "enable Power Nap" should be the solution??? I have unticked these options in Energy Saver preferences

No, or not entirely (I have a LAN and a WIFI). This depend if you are in a net (google):

  • Macs with USB-connected printers, providing Printer Sharing.
  • Macs with iTunes media, being served to Apple TVs or other iTunes machines.
  • Back to My Mac machines at home that are sleeping, and then woken on demand when you connect to them (from inside or outside the home).
  • Command-line login using ssh. 
  • Any other Bonjour-advertised service.

and if enabled the device remains asleep while the sleep proxy server responds to any Multicast DNS queries.

It does mean that dns/mac addresses are recycled across devices and the service awake the system because a listener send a message to it. If you aren't connected in any of those mentioned, you may want to use "Wake for network acces" with out having any Bonjour service enable (if you don't have a Apple router or Time Capsule?). Or at least what I'v undertood..

Edited by vector sigma
typos

Share this post


Link to post
Share on other sites

Hello. On previous versions, I use an EFI driver called "AptioMemoryFix-64". But it's not available anymore. Is there an existing equivalent? thanks

Share this post


Link to post
Share on other sites
15 minutes ago, mrjayviper said:

Hello. On previous versions, I use an EFI driver called "AptioMemoryFix-64". But it's not available anymore. Is there an existing equivalent? thanks

 

Hi. You can find it in Clover Installer PKG. Take a look in latest release r5098

Share this post


Link to post
Share on other sites
16 hours ago, Pene said:

 

 

 

Following this problem, I have narrowed it down to the rank of DIMMs used.

This error appears during install when he is trying to install with Single-Rank DIMMs (2x8GB).

The error does not appear, and he can install successfully, when trying to install with Dual-Rank DIMMs (also 2x8GB).

 

The memory rank information appears in SMBIOS, at Type17->Attributes (0Bh), maybe it needs to be taken into consideration for something? (currently we are not doing anything with it within Clover)

It still baffles me though how it can affect the installer to give this error. Also, if the Single-Rank DIMMs are put back after macOS is already installed, everything seems to be functioning properly.

It is very interesting find.

Clover doesn't do anything with the field

  //
  // Add for smbios 2.6
  //
  UINT8                                     Attributes;

because it was developed very long ago for older macs with Smbios 2.4.

We can add this line

    newSmbiosTable.Type17->MemoryErrorInformationHandle = 0xFFFF;
+   newSmbiosTable.Type17->Attributes = 0x0B;
    mHandle17[gRAMCount++] = LogSmbiosTable(newSmbiosTable);
  }

We have to know if it will not break anything else.

Make this patch conditional through config.plist?

Share this post


Link to post
Share on other sites
1 hour ago, Slice said:

It is very interesting find.

Clover doesn't do anything with the field


  //
  // Add for smbios 2.6
  //
  UINT8                                     Attributes;

because it was developed very long ago for older macs with Smbios 2.4.

We can add this line


    newSmbiosTable.Type17->MemoryErrorInformationHandle = 0xFFFF;
+   newSmbiosTable.Type17->Attributes = 0x0B;
    mHandle17[gRAMCount++] = LogSmbiosTable(newSmbiosTable);
  }

We have to know if it will not break anything else.

Make this patch conditional through config.plist?

 

Hi Slice,

 

Thank you for the response. But I think I didn't explain myself well.

0Bh is the location of of the "Attributes", not it's content.

The content is newSmbiosTable.Type17->Attributes = 1 in case of Single-Rank DIMMs and newSmbiosTable.Type17->Attributes = 2 in case of Dual-Rank DIMMs.

But this information is *already present* in SMBIOS, without us doing anything special in Clover.

 

He sent me two dmidecodes from a booted Mac, for each case, with the different DIMMs installed. Look:

 

This is the non-working case with the Single-Rank DIMMS: (notice the RANK: 1, it is present in smbios and read from the Attributes address at 0Bh):

Handle 0x1101, DMI type 17, 40 bytes
Memory Device
	Array Handle: 0x1000
	Error Information Handle: No Error
	Total Width: 64 bits
	Data Width: 64 bits
	Size: 8192 MB
	Form Factor: DIMM
	Set: 1
	Locator: DIMM0
	Bank Locator: BANK 1
	Type: DDR4
	Type Detail: Synchronous Unbuffered (Unregistered)
	Speed: 2998 MT/s
	Manufacturer: Corsair
	Serial Number: 0000000000000000
	Asset Tag: Not Specified
	Part Number: CMW16GX4M2C3000C15
	Rank: 1
	Configured Clock Speed: 2133 MT/s
	Minimum Voltage: 1.2 V
	Maximum Voltage: 1.2 V
	Configured Voltage: 1.2 V

And this is the non-working case with the Dual-Rank DIMMS: (notice the RANK: 2, it is present in smbios and read from the Attributes address at 0Bh):

Handle 0x1100, DMI type 17, 40 bytes
Memory Device
	Array Handle: 0x1000
	Error Information Handle: No Error
	Total Width: 64 bits
	Data Width: 64 bits
	Size: 8192 MB
	Form Factor: DIMM
	Set: 1
	Locator: DIMM0
	Bank Locator: BANK 0
	Type: DDR4
	Type Detail: Synchronous Unbuffered (Unregistered)
	Speed: 3200 MT/s
	Manufacturer: G Skill Intl
	Serial Number: 0000000000000000
	Asset Tag: Not Specified
	Part Number: F4-3200C16-8GTZB
	Rank: 2
	Configured Clock Speed: 2133 MT/s
	Minimum Voltage: 1.2 V
	Maximum Voltage: 1.2 V
	Configured Voltage: 1.2 V

This is the only real difference between the chips.

He has two pairs of chips that it is working OK for install with them (one pair is 2x8GB - GSKILL the other is 2x16GB - CORSAIR). Both of these are working OK for install and both are with "Rank: 2".

He has only one pair with "Rank: 1" (they are more rare I think), but install keeps giving the error with them in all cases, also if using only a single DIMM, also when using both DIMMs.

 

I don't know what we should be doing with this information, I was mentioning it as maybe together we can understand what is going on here...

 

I tried, on my system, to add:

newSmbiosTable.Attributes = 1 

Just to see if it makes me also get the error (as my Rank also was 2) - but the error did not appear on my System (I don't actually have single-rank DIMMs to test with them, so I tried only to fake the rank).

 

There are many reports on the net (at other sites) about this issue, no one mentioned the Rank, but in most cases it was closed by using other DIMMs or moving the DIMMs in other slots (on boards that have more slots). So this is a memory issue, and in my opinion is is somehow related to the Rank. 

 

 

 

 

Share this post


Link to post
Share on other sites

My computer reported

Handle 0x1100, DMI type 17, 40 bytes
0000: 11 28 00 11 00 10 ff ff ff ff ff ff 00 00 09 01 
0010: 01 02 00 80 00 00 00 00 00 00 00 00 00 00 00 00 
0020: 00 00 00 00 00 00 00 00 

Memory Device
	Array Handle: 0x1000
	Error Information Handle: No Error
	Total Width: Unknown
	Data Width: Unknown
	Size: No Module Installed
	Form Factor: DIMM
	Set: 1
	Locator: DIMM0
	Bank Locator: BANK 0
	Type: <OUT OF SPEC>
	Type Detail: Synchronous
	Speed: Unknown
	Manufacturer: Not Specified
	Serial Number: Not Specified
	Asset Tag: Not Specified
	Part Number: Not Specified
	Rank: Unknown
	Configured Clock Speed: Unknown
	Minimum voltage:  Unknown
	Maximum voltage:  Unknown
	Configured voltage:  Unknown

So why I have similar problem?

It was empty slot.

Occupied slot has info

Handle 0x1103, DMI type 17, 40 bytes
0000: 11 28 03 11 00 10 ff ff 40 00 40 00 00 10 09 02 
0010: 01 02 1a 80 00 55 08 03 04 00 06 01 00 00 00 00 
0020: 55 08 b0 04 b0 04 b0 04 

Memory Device
	Array Handle: 0x1000
	Error Information Handle: No Error
	Total Width: 64 bits
	Data Width: 64 bits
	Size: 4096 MB
	Form Factor: DIMM
	Set: 2
	Locator: DIMM1
	Bank Locator: BANK 1
	Type: <OUT OF SPEC>
	Type Detail: Synchronous
	Speed: 2133 MHz (0.5 ns)
	Manufacturer: 0000
	Serial Number: 0000000000000000
	Asset Tag: Not Specified
	Part Number: unknown
	Rank: 1
	Configured Clock Speed: 2133 MHz (0.5 ns)
	Minimum voltage:  1.200 V
	Maximum voltage:  1.200 V
	Configured voltage:  1.200 V

There is Rank=1, and there is Type <OUT OF SPEC>. I think Apple doesn't like wrong field in Smbios. We should somehow fill them.

Share this post


Link to post
Share on other sites
4 hours ago, Slice said:

So why I have similar problem?

It was empty slot.

Occupied slot has info

There is Rank=1, and there is Type <OUT OF SPEC>. I think Apple doesn't like wrong field in Smbios. We should somehow fill them.

Is this the computer that gives you similar error in install (by the way, is it the exact same message?) Does the error reproduce when you run an installation? If yes maybe it really is the same problem with single rank.

 

Also, I can't be sure that it will happen in all cases with Rank=1, it may depend also on placement in slots, or other factors.

 

But in his case information is correct in smbios. He really has single-rank ram memory in both slots and it is reported accordingly.

Edited by Pene

Share this post


Link to post
Share on other sites

Yes, it is this computer. 

I got this error updating 10.14.3 to 10.14.6, while clean installation of 10.14.6 was successful.

Strange that the error was checked only by installer. Final OS works.

Also strange my way to resolve the problem: boot by legacy Clover. It is not using AptioFix and this is the difference related to memory.

It's a pity we have no reproducible tests.

Share this post


Link to post
Share on other sites

Well my friend can reproduce it every time if he tries clean install with both Catalina and Mojave with that single rank ram. But I don't really have an idea what solution to offer for him to test...

Share this post


Link to post
Share on other sites
17 hours ago, Pene said:

Well my friend can reproduce it every time if he tries clean install with both Catalina and Mojave with that single rank ram. But I don't really have an idea what solution to offer for him to test...

Make a Clover with Attributes=2 and test again.

Share this post


Link to post
Share on other sites

Hi,

 

newbie here... Can someone direct me to some wiki / documents that explains in depth what does each option do in Clover's customization screen when installing? For instance I see instructions where people will say to install as Boot0AF or Boot0SS in legacy which sounds a bit like a contradiction... So instead of doing a copy a paste of others instructions I would like to have a better grasp / understanding of Clover installing process.

Share this post


Link to post
Share on other sites
13 hours ago, mozbius said:

Hi,

 

newbie here... Can someone direct me to some wiki / documents that explains in depth what does each option do in Clover's customization screen when installing? For instance I see instructions where people will say to install as Boot0AF or Boot0SS in legacy which sounds a bit like a contradiction... So instead of doing a copy a paste of others instructions I would like to have a better grasp / understanding of Clover installing process.

https://www.insanelymac.com/forum/topic/282787-clover-v2-instructions/

https://sourceforge.net/p/cloverefiboot/wiki/Home/

Instructions mostly outdated so ask at the forum what you have a question.

boot0af is recommended for actual configuration when you have GPT disk with partitions:

disk0s1  - EFI

disk0s2 - system, and more

So legacy boot will follow this algorithm:

1. BIOS will call HDD, read zero sector where boot0af installed.

2. boot0af will transfer execution to first sector in EFI partition where boot1f32 installed.

3. boot1f32 will load boot file (usually the copy of boot6) which is the legacy Clover containing EFI framework (so called CloverEFI).

4. CloverEFI will call CloverX64.efi which is GUI.

 

boot0ss is for old MBR formatted HDD. This is separate story.

Share this post


Link to post
Share on other sites

@Pene

I pushed some changes to Clover related to smbios. Among them is the possibility to set MemoryRank (1 or 2 or keep native if not set) and a possibility to set SmbiosVersion. It is 2.4 before now. May be we have to follow new MacModels which have 3.0 or other versions.

If you can test it will be interesting to see if something changed.

Share this post


Link to post
Share on other sites
3 hours ago, Slice said:

@Pene

I pushed some changes to Clover related to smbios. Among them is the possibility to set MemoryRank (1 or 2 or keep native if not set) and a possibility to set SmbiosVersion. It is 2.4 before now. May be we have to follow new MacModels which have 3.0 or other versions.

If you can test it will be interesting to see if something changed.

 

Thanks a lot specially for the possibility to set Custom SmbiosVersion :)

 

How I can know the appropriate value for new Mac Models and how to set correct string (hex value) in the config.plist?

 

Sorry for my bad english

 

EDIT: I don't understand what is the right syntax: for example, 0x26 or 0x0206

 

Capture d’écran 2019-11-15 à 17.50.48.png

Capture d’écran 2019-11-15 à 17.52.05.png

Edited by Matgen84

Share this post


Link to post
Share on other sites
1 hour ago, Matgen84 said:

 

Thanks a lot specially for the possibility to set Custom SmbiosVersion :)

 

How I can know the appropriate value for new Mac Models and how to set correct string (hex value) in the config.plist?

 

Sorry for my bad english

 

For example iMac17,1 has SmbiosVersion 3.0 as see in ioreg

Снимок экрана 2019-11-15 в 20.12.39.png

So in Clover we may write

SMBIOS->SmbiosVersion

<string>0x0300</string>

 

Or for older Mac

0x0206

to be version 2.6

Share this post


Link to post
Share on other sites
On 11/13/2019 at 1:57 AM, Pene said:

Well my friend can reproduce it every time if he tries clean install with both Catalina and Mojave with that single rank ram. But I don't really have an idea what solution to offer for him to test...

 

my desktop has same issue. it installed 8g ram with sing bank.

i didnt set ram info in config.plist. im using imac17.1 smbios jn config.

always fail clean install. i tried all but fail.

i just have to install high sierra and update mojave or catalina. i can' directly install mojave+.

my laptop case, my laptop have to set ram on smbios part to boot macos in config. it has actually single ram bank and 8g ram. it never fail macos installation. my laptop set mbp13,1.

 

thank you for this report that i have been problem.

Share this post


Link to post
Share on other sites
1 minute ago, Sherlocks said:

 

my desktop has same issue. it installed 8g ram with sing bank.

i didnt set ram info in config.plist. im using imac17.1 smbios jn config.

always fail clean install. i tried all but fail.

i just have to install high sierra and update mojave or catalina. i can' directly install mojave+.

my laptop case, my laptop have to set ram on smbios part to boot macos in config. it has actually single ram bank and 8g ram. it never fail macos installation. my laptop set mbp13,1.

 

thank you for this report that i have been problem.

Did you differ "single bank" and "single rank ram"?

Share this post


Link to post
Share on other sites
59 minutes ago, Slice said:

For example iMac17,1 has SmbiosVersion 3.0 as see in ioreg

 

So in Clover we may write

SMBIOS->SmbiosVersion

<string>0x0300</string>

 

Or for older Mac

0x0206

to be version 2.6

But SMBIOS v3 has other entry point and other GUID so I can't recommend to use it until all standards will be followed.

Share this post


Link to post
Share on other sites
6 hours ago, Slice said:

@Pene

I pushed some changes to Clover related to smbios. Among them is the possibility to set MemoryRank (1 or 2 or keep native if not set) and a possibility to set SmbiosVersion. It is 2.4 before now. May be we have to follow new MacModels which have 3.0 or other versions.

If you can test it will be interesting to see if something changed.

Hi Slice,

Thanks.

Meanwhile. he tested with changed Rank (Attributes=2, before your latest changes) but unfortunately there was no change, install still failed. So changing this in smbios didn't really help

He said he will send me the memory chips so that I can make more investigations. But it will take a while till he sends them.

2 hours ago, Sherlocks said:

 

my desktop has same issue. it installed 8g ram with sing bank.

i didnt set ram info in config.plist. im using imac17.1 smbios jn config.

always fail clean install. i tried all but fail.

i just have to install high sierra and update mojave or catalina. i can' directly install mojave+.

my laptop case, my laptop have to set ram on smbios part to boot macos in config. it has actually single ram bank and 8g ram. it never fail macos installation. my laptop set mbp13,1.

 

thank you for this report that i have been problem.

What is your memory rank in dmidecode -t 17?

Also, your error is the exact one that my friend is reporing? 

Edited by Pene

Share this post


Link to post
Share on other sites
10 hours ago, Pene said:

Hi Slice,

Thanks.

Meanwhile. he tested with changed Rank (Attributes=2, before your latest changes) but unfortunately there was no change, install still failed. So changing this in smbios didn't really help

He said he will send me the memory chips so that I can make more investigations. But it will take a while till he sends them.

What is your memory rank in dmidecode -t 17?

Also, your error is the exact one that my friend is reporing? 

Hi Pene,

I see real iMac18,3 also has Rank=1

Handle 0x0001, DMI type 17, 40 bytes
0000: 11 28 01 00 00 00 fe ff 40 00 40 00 00 10 0d 00 
0010: 01 02 1a 80 00 60 09 03 04 05 06 01 00 00 00 00 
0020: 60 09 00 00 00 00 b0 04 

Memory Device
	Array Handle: 0x0000
	Error Information Handle: Not Provided
	Total Width: 64 bits
	Data Width: 64 bits
	Size: 4096 MB
	Form Factor: SODIMM
	Set: None
	Locator: DIMM0
	Bank Locator: BANK 0
	Type: <OUT OF SPEC>
	Type Detail: Synchronous
	Speed: 2400 MHz (0.4 ns)
	Manufacturer: 0x802C
	Serial Number: 0x21211463
	Asset Tag:  
	Part Number: 0x344154463531323634485A2D3247334232202020
	Rank: 1
	Configured Clock Speed: 2400 MHz (0.4 ns)
	Minimum voltage:  Unknown
	Maximum voltage:  Unknown
	Configured voltage:  1.200 V

What is the size of your DIMM? Before my latest commit there was a problem with 32Gb modules. Ticket 595.

Share this post


Link to post
Share on other sites
13 hours ago, Slice said:

But SMBIOS v3 has other entry point and other GUID so I can't recommend to use it until all standards will be followed.

Up to iMac15,1 Apple used SmbiosVersion 2.4.

Since iMac17,1 I see SmbiosVersion 3.0.

Share this post


Link to post
Share on other sites
15 hours ago, Slice said:

Hi Pene,

I see real iMac18,3 also has Rank=1

What is the size of your DIMM? Before my latest commit there was a problem with 32Gb modules. Ticket 595.

The dimm where install fails is a rank1 8gb x2 chips each (Corsair, total 16gb)

Install was ok with rank 2 8gb x2 chips (Gskill, total 16gb)

And also was ok on with rank 2 16gb x2 chips  (Corsair, total 32gb)

That's why I thought it is probably related to rank, as there was no other major difference between the chips where it worked and failed. Same size also as you see.

He was using iMac19,2 model.

 

Edited by Pene

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Content

    • By Aldaro
      Gigabyte, in their infinite wisdom, decided to remove the option to disable serial ports, and not being able to do so has been causing me some problems. I know that I have to either use a patch in clover, or create a custom SSDT to disable super I/O, but I honestly do not know how to go about doing this. One of the weirder problems I'm experiencing is the inability to connect to Apple Music (error 11556) unless I go into my network settings, and delete my serial connection. If anyone could help me out with this, that'd be greatly appreciated; anyway, thank you for taking the time to read this.
       
      SPECS:
      Mobo GIGABYTE Z390 M GAMING (UEFI F8)
      CPU: i5 9600k
      RAM: 32GB DDR4 @ 2666 Mhz
      GPU: AMD Radeon RX 580 w/ 8GB of VRAM (MSI armor oc edition)
      Storage Samsung 970 evo 500GB
    • By cvad
      View File Bootdisk Utility
      Make bootable USB Flash Disk for MAC OS X with Latest Clover bootloader revision fast and easy by one click! under OS Windows.
      Special utility from cvad & russian MAC community for new hackintosh users.
       
      Enjoy...
       
      For more information and complete instructions please see this topic.
       
       
       
       
      Feel free to "Rate File"
      Submitter cvad Submitted 04/28/2013 Category Bootloaders  
    • By e97
      HackPro X99 System
      Until Apple blesses us with the MacPro7,1 – this is for those that require tools to do their work.
      An appropriate bicycle for the mind.
       
       

       

       

       
      Specs:
       
      CPU: Intel Xeon E5-2678 v3 (12 core, 2.5 GHz / 3.3 GHz Boost)
      Motherboard: SZMZ X99-8D3
      RAM: 16GB DDR3-14900R 1866Mhz ECC RDIMM modules
      GPU: Radeon RX Vega 64 8GB
      Storage: Phison E12 m.2 NVMe PCI-E 3.0 x4 SSD
      Water blocks: BARROW CPU + GPU
      Radiator: 360mm x 25mm slim
      Pump: DDC
       
      Case dimensions: 431 mm x 342 mm x 177 mm
       
       
       
      XCPM OFF
       

       
      XCPM ON
       

       
      OpenCL
       

       
       
       
      iMacPro1,1
       

       
       

       
      OpenCL
       

       
       
      NVMe
       

       
       
      Win 10 x64 v1809
       
      AIDA64 - Cache & Memory
       

       
       
      Download:  https://github.com/xe97/X99-8D3-Clover
       
       
       
       
       
      Anyone else I forgot
       
       
    • By digivish
      Hi All - quick thing - I have a NUC 8i7BEH with 32GB RAM and 2 x 1TB SSD drives. Each drive has its own OS - Windows 10 and Catalina 10.15.
       
      Clover works well - Catalina Boots, so does Windows.
      Catalina - has sound over HDMI (to my monitor's speakers)
      Windows - no audio device found - It does show Realtek and Intel Display Drivers - but the speaker has a red"x" and in Devices, there is no entry for Microphone Array under Audio Input/Output. It does, however, show Intel display over the HDMI - but actually no sound.
       
      I have tried reinstalling Realtek drivers - now here's the thing...when it installs, it first uninstalls existing Realtek drivers - at this stage (and it's important) the sound starts working - as if uninstalling did the trick. As part of the installing, I have to reboot and upon reboot, it actually reinstalls the Realtek drivers. After that, I'm back to square 1. Unsure if it's the config.plist or boot args in clover. But something with Clover for sure.
       
      I have tested this by removing the Mac Drive with clover and just booting directly to Windows 10 bootloader and everything works as it should, I have sound over HDMI and the audio device shows. Just not when I boot with Clover.
       
      has anyone experienced this and have thoughts or pointers.
       
      Thanks a ton!
×