Jump to content
ErmaC

Clover General discussion

22,349 posts in this topic

Recommended Posts

Is it possible to install Windows ISO to SSD partition use clover on legacy BIOS boot and GPT partition scheme?

 

Doesn't work again,I don't change anything,why this happened?

Figure out why my IDE optical drive doesn't work,clover doesn't inject ApplePCIIDE.kext,I install it with KextUtility in /S/L/E,problem solved.I don't know this instruction #30 explain this thing.

Figure out

	<key>SystemParameters</key>
	<dict>
		<key>InjectKexts</key>
		<string>Detect</string>
	</dict>

Detect - Kexts from /EFI/CLOVER/kexts/ will be injected only if FakeSMC is not present in the kernelcache

http://clover-wiki.zetam.org/Configuration/SystemParameters#InjectKexts[/size]

This solved my problem,I install HWMonitor make Clover doesn't inject kexts,is this wiki write by you slice?

 

But there is another problem,I use sleep and wake up and [/size]overclock,here is my overclock settings

CPU Clock Ratio...........................9 x
CPU Clock.................................445 MHz

Voltage Setting Page
CPU VID Special Add.......................+250mV
DRAM Voltage Control......................2.290V
CPU GTL 0/2 REF Volt......................0.63X
CPU GTL 1/3 REF Volt......................0.61X
North Bridge GTL REF Volt.................0.58X

CAS Latency Time (tCL)....................5
RAS# to CAS# Delay (tRCD).................6
RAS# Precharge (tRP)......................6
Precharge Delay (tRAS)....................18

When I use wake up from sleep with 445x9,instant of restart.With 400x9,wake up fine.I think the problem is BIOS use the default settings to overclock 445x9,which only works on 400x9.How can I use wake up and overclock both?

 

I find out I cannot wake up from sleep with 445x9 in yosemite,so I use 

 

CPU Clock Ratio...........................9 x
CPU Clock.................................430 MHz

Voltage Setting Page
CPU VID Special Add.......................+300mV
DRAM Voltage Control......................2.100v
CPU GTL 0/2 REF Volt......................0.63X
CPU GTL 1/3 REF Volt......................0.61X
North Bridge GTL REF Volt.................0.58X

CAS Latency Time (tCL)....................5
RAS# to CAS# Delay (tRCD).................6
RAS# Precharge (tRP)......................6
Precharge Delay (tRAS)....................18

wake up from sleep works

300mv 2.100v 63 61 58 5 6 6 18 425x9 pass cs:go 8 rounds geek bench 3612

300mv 2.338v 63 61 58 5 6 6 18 425x9 pass cs:go 8 rounds geek bench 3976

300mv 2.338v 63 61 58 5 6 6 18 435x9 boot fail

300mv 2.338v 63 61 58 5 6 6 18 440x9 yosemite wake up from sleep fail

300mv 2.338v 63 61 58 5 6 6 18 430x9 pass cs:go 8 rounds geek bench 4028

300mv 2.218v 63 61 58 5 6 6 18 430x9 geekbench 3955

300mv 2.100v 63 61 58 5 6 6 18 430x9 geekbench 4032

250mv 2.100v 63 61 58 5 6 6 18 430x9 boot fail restart

However there is another problem,with dsdt.aml fix I cannot wake up by keyboard,only by mouse and power button,with clover fix only power button wake up success,how can I fix this?

Share this post


Link to post
Share on other sites
Advertisement

There is some build error in latest version 3170

 

/Users/alex/CloverGrowerPro/edk2/Clover/rEFIt_UEFI/Platform/ati.c:100:20: error: expected '}' before '.' token
  {"IkuraS",      1}.
                    ^
make: *** [/users/alex/CloverGrowerPro/edk2/Build/Clover/RELEASE_GCC49/X64/Clover/rEFIt_UEFI/refit/OUTPUT/Platform/ati.obj] Error 1


build.py...
 : error 7000: Failed to execute command
    make tbuild [/users/alex/CloverGrowerPro/edk2/Build/Clover/RELEASE_GCC49/X64/Clover/rEFIt_UEFI/refit]


build.py...
 : error F002: Failed to build module
    /Users/alex/CloverGrowerPro/edk2/Clover/rEFIt_UEFI/refit.inf [X64, GCC49, RELEASE]

- Failed -
Build end time: 18:35:00, Feb.11 2015
Build total time: 00:06:28

Cloverx64 release  ERROR!!

 

Share this post


Link to post
Share on other sites

Why does over/underclocking using Clover cause time lag & audio stutter? (RTC/HPET?)

Is there a way I can fix the lag/stutter? Can Clover somehow compensate for this? (maybe RTC calibration?).

 

I know its not a clover issue. I'm probably asking for too much, but it would be nice if it were possible...

 

Thanks in advance :)

Share this post


Link to post
Share on other sites

Why does over/underclocking using Clover cause time lag & audio stutter? (RTC/HPET?)

Is there a way I can fix the lag/stutter? Can Clover somehow compensate for this? (maybe RTC calibration?).

 

I know its not a clover issue. I'm probably asking for too much, but it would be nice if it were possible...

 

Thanks in advance :)

Because Clover is not changing neither BusSpeed nor Cpu Speed. It can only tell to system what are these values. If these value will be over/under their real values then the system will work abnormal: lags, hangs, Audio squeak,  scratch.

 

 

 

one more question windows is installs with clover only from DVD not usb or bootable usb 

???

I did with DVD ISO9660+Joilet.

I think USB is also possible. Why not?

There is some build error in latest version 3170

 

/Users/alex/CloverGrowerPro/edk2/Clover/rEFIt_UEFI/Platform/ati.c:100:20: error: expected '}' before '.' token

  {"IkuraS",      1}.

                    ^

make: *** [/users/alex/CloverGrowerPro/edk2/Build/Clover/RELEASE_GCC49/X64/Clover/rEFIt_UEFI/refit/OUTPUT/Platform/ati.obj] Error 1

 

 

build.py...

 : error 7000: Failed to execute command

    make tbuild [/users/alex/CloverGrowerPro/edk2/Build/Clover/RELEASE_GCC49/X64/Clover/rEFIt_UEFI/refit]

 

 

build.py...

 : error F002: Failed to build module

    /Users/alex/CloverGrowerPro/edk2/Clover/rEFIt_UEFI/refit.inf [X64, GCC49, RELEASE]

 

- Failed -

Build end time: 18:35:00, Feb.11 2015

Build total time: 00:06:28

 

Cloverx64 release  ERROR!!

 

 

Corrected in 3171

-	{"IkuraS",      1}.
+	{"IkuraS",      1},

Anyone see difference?

Share this post


Link to post
Share on other sites

Question - after being unavailable for so many days do we now conclude that the website "Project OS X Forums" is  finally dead and buried?

 

It was useful from a Clover perspective, full of information but badly organised and administered.

Share this post


Link to post
Share on other sites

Error again with latest Clover

 

/Users/alex/CloverGrowerPro/edk2/Clover/rEFIt_UEFI/Platform/ati.c:437:24: error: 'CHIP_FAMILY_SUMO2' undeclared here (not in a function)
  { 0x9642, 0x00000000, CHIP_FAMILY_SUMO2, "AMD Radeon HD 6370D", kNull       },
                        ^
make: *** [/users/alex/CloverGrowerPro/edk2/Build/Clover/RELEASE_GCC49/X64/Clover/rEFIt_UEFI/refit/OUTPUT/Platform/ati.obj] Error 1


build.py...
 : error 7000: Failed to execute command
    make tbuild [/users/alex/CloverGrowerPro/edk2/Build/Clover/RELEASE_GCC49/X64/Clover/rEFIt_UEFI/refit]


build.py...
 : error F002: Failed to build module
    /Users/alex/CloverGrowerPro/edk2/Clover/rEFIt_UEFI/refit.inf [X64, GCC49, RELEASE]

- Failed -
Build end time: 17:47:43, Feb.12 2015
Build total time: 00:06:02

Cloverx64 release  ERROR!!

Share this post


Link to post
Share on other sites

-    CHIP_FAMILY_SUMO2,

+    CHIP_FAMILY_SUMO2,

To add or not..

Share this post


Link to post
Share on other sites
Slice, too bad the Project OS X Forums are dead.
 
I found the "Clover Changes" pages very useful in particular.
 

 

Any plans to maintain this important (imho) information elsewhere? Maybe on these forums?

Share this post


Link to post
Share on other sites

Riley, I can see that, but that seems like only a fraction of the information. Still think a dedicated thread with further explanations would be very helpful

Share this post


Link to post
Share on other sites

 

Slice, too bad the Project OS X Forums are dead.
 
I found the "Clover Changes" pages very useful in particular.
 

 

Any plans to maintain this important (imho) information elsewhere? Maybe on these forums?

 

Yes, on these forum. As far as there will be significant changes compared to 3100 revision.

Share this post


Link to post
Share on other sites

Slice, that's great to hear! I am especially curious about the changes with the new upcoming major version.

 
So please keep us updated with the latest changes, and I also want to thank you and your collegues for your excellent work.

Share this post


Link to post
Share on other sites

Who is Rufus?

My IDea is in "Clover Instructions".

Rufus  is a Tools to create bootable usb of windows on windows , 

 

 

My IDea is in "Clover Instructions".

what you want to say , any instruction im able to test and want install windows 8.1 which GPT only in UEFI 

... that is not working...

 

Clover installer can make USB media to be bootable.

its not making bootable , 

what are the steps ???

Share this post


Link to post
Share on other sites

Created /Users/naiclub/CloverGrowerPro/edk2/Build/Clover/RELEASE_GCC48/FV/Efildr64


GenPage...


/Users/naiclub/CloverGrowerPro/edk2/Build/Clover/RELEASE_GCC48/FV/Efildr20Pure: ERROR 16386: Invalid parameter option


  Input file size (0x6c9e0) exceeds the Page Table Offset (0x68000)<<<


Cloverx64 release  ERROR!!


 


 


Ejecting RAM disk


"disk5" unmounted.


"disk5" ejected.


logout


It is said that the capacity of the RAM disk beyond.

Any opinions

Share this post


Link to post
Share on other sites

Rufus  is a Tools to create bootable usb of windows on windows , 

what you want to say , any instruction im able to test and want install windows 8.1 which GPT only in UEFI 

its not making bootable , 

what are the steps ???

I mean this instructions             #46            

You have to start Clover and then choose bootgmr.efi from /EFI/microsoft/...

USB or DVD may not be bootable because we tell about UEFI boot.

But there is a question. If you made USB with Rufus then where will be Clover?

 

Created /Users/naiclub/CloverGrowerPro/edk2/Build/Clover/RELEASE_GCC48/FV/Efildr64

GenPage...

/Users/naiclub/CloverGrowerPro/edk2/Build/Clover/RELEASE_GCC48/FV/Efildr20Pure: ERROR 16386: Invalid parameter option

  Input file size (0x6c9e0) exceeds the Page Table Offset (0x68000)

Cloverx64 release  ERROR!!

 

 

Ejecting RAM disk

"disk5" unmounted.

"disk5" ejected.

logout

It is said that the capacity of the RAM disk beyond.
Any opinions

 

My proposition is to switch to gcc-4.9

Generating DUETEFIMAINFVX64 FV
########################################
########################################
########################################
####################
GUID cross reference file can be found at /Users/slice/src/edk2/Build/Clover/RELEASE_GCC49/FV/Guid.xref

FV Space Information
DUETEFIMAINFVX64 [35%Full] 2752512 total, 969400 used, 1783112 free

- Done -
Build end time: 20:06:38, Feb.13 2015
Build total time: 00:00:32

Compressing DUETEFIMainFv.FV ...
Encoding
Compressing DxeMain.efi ...
Encoding
Compressing DxeIpl.efi ...
Encoding
Generate Loader Image ...
Created /Users/slice/src/edk2/Build/Clover/RELEASE_GCC49/FV/Efildr64
879+0 records in
879+0 records out
450048 bytes transferred in 0.006982 secs (64459709 bytes/sec)
/Users/slice/src/edk2/Build/Clover/RELEASE_GCC49/FV/boot -> /Users/slice/src/edk2/Clover/CloverPackage/CloverV2/Bootloaders/x64/boot6

Share this post


Link to post
Share on other sites

@InsanelyDeepak + Slice

I'm not expert but i made some test for install Windows (Uefi bios), I always used Rufus my advice is star Rufus USB Win from bios not from clover (only for first installation) because when I started Win8 installation from clover it has created Microsoft folder, needed to start Windows, good for legacy but not for UEFI). You can also create DVD to install Win8 without UEFI mode (I don't know why) and you can see Windows partition from Mac preferences/Boot Disk.

 

@Slice
Advice for C3Latency, in config.plist we need use decimal value or hex value?

You said:

Typical values from native Mac: (IvyBridge)

MacPro5,1 - 17

MacPro6,1 - 67

iMac13,2 - 205

MacBookPro9,2 - 198

but I'm using 0x43 for my E5-1620v2 (MacPro6,1 Smbios) 

 

Advice for Haswell + Macpro Smbios?

Any Mac Haswell standard values?

 

Thanks

Share this post


Link to post
Share on other sites

 

 

But there is a question. If you made USB with Rufus then where will be Clover?

using two ways 

1. BDU usb 200 mb partitioned rest with rufus 

2.My HDD already has Clover Installed 

 

i don't have bootmgr.efi in Boot folder its in root directorysee this

 post-1425204-0-93088600-1423850764_thumb.png ,

 

how to load this using clover 

 

 

 

 

Thank you 

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

Announcements

  • Similar Content

    • By STLVNUB
      *Put the script into its own folder as it will create other folders*
      What is BTB?
      Script file to clone and help build Clover or Opencore repos
      Script will create link to itself in /usr/local/bin/bob
      Script SHOULD fix up any stray bobs you may have.
      Then you only need to type bob. and a parameter
      "a" for ACID repo, official
      "d" for ACID repo DUET build
      "c" for CLOVER
      "e" to erase UDK Folder
      Easier typing bob than.....usual stuff
      YOU WILL NEED TO cmod+x THE SCRIPT
      Enjoy
       
    • By cvad
      View File Bootdisk Utility
      Make bootable USB Flash Disk for MAC OS X with Latest Clover bootloader revision fast and easy by one click! under OS Windows.
      Special utility from cvad & russian MAC community for new hackintosh users.
       
      Enjoy...
       
      For more information and complete instructions please see this topic.
       
      Anyone who likes the program, please support its Community Score.
       
       
      Feel free to "Rate File"
      Submitter cvad Submitted 04/28/2013 Category Bootloaders  
    • By PropoFlexWX4
      After hearing that OpenCore is so much better than Clover, and that it will probably be able to boot Big Sur before Clover does, I decided to take the jump.
       
      Running Catalina 10.15.5 18F101 with OC 0.5.9.
       
      So far I like the result. The OS feels faster, boots faster.
      And absolutely everything works (sleep, network, etc...)
       
      So, that's it? Is there anything else I have to do?
×