Jump to content
ErmaC

Clover General discussion

19,022 posts in this topic

Recommended Posts

Advertisement

Hey guys

 

With my system up and running again (with both internet and sound working, thanks to two awesome guys here :) ), I tried to boot from the HDD, with no USB used for bootloader.

 

And so, I installed Clover, in UEFI mode, with the same drivers for UEFI as the ones on the actual Yosemite USB stick, but on my Yosemite partition and started to boot up the system without the USB stick. And I couldn't. I got stuck half way on boot-up. The loading bar doesn't get past 50% loading.

 

So I thought this might be because I didn't add FakeSMC.kext into System/Library/Extensions. And so, I booted up with the USB stick again and I copied the FakeSMC.kext from my USB stick (I previously created a folder for 10.10 in EFI folder on my USB stick - there was a "kexts" folder somewhere in there- ) to my System/Library Extensions on my Yosemite partition. I used that awesome command that Slice gave me to clear cache for Startup and tried again. Same result.

 

Any idea how to properly install Clover on my HDD? I'm planning on switching Mavericks to Clover, as well, since it seems to boot just fine with it.

 

So, to make things more clearer, right now, I've got:

1. Mavericks (bootable with Chimera, in legacy BIOS mode)

2. Yosemite (bootable with Clover in UEFI mode)

3. two other partitions for storage

 

How do I make both of them bootable, with Clover, and no USB stick? This is the question. Mavericks already is bootable, but, as I said, it uses Chimera.

Share this post


Link to post
Share on other sites

Does anyone have a solution for my unbootable system?

Not good idea, isn't it?

35:311  0:009   Table: SSDT  SataTabl  877 dropped
35:320  0:009   Table: SSDT  SaSsdt   13537 dropped

If you have a problem of patching AppleTyMCE the I see no debug messages like

DBG_RT("\nAnyKextPatch %d: driverAddr = %x, driverSize = %x\nAnyKext = %a\n",

so can't say it occured.

Set

	<key>KernelAndKextPatches</key>
	<dict>
		<key>Debug</key>
		<true/>

And see messages on the screen. Debug.log is not possible here.

 

I may propose you just remove the kext. It is not needed.

 

Any idea how to properly install Clover on my HDD? I'm planning on switching Mavericks to Clover, as well, since it seems to boot just fine with it.

 

 

 

How do I make both of them bootable, with Clover, and no USB stick? This is the question. Mavericks already is bootable, but, as I said, it uses Chimera.

Use official installer!

Share this post


Link to post
Share on other sites

Use official installer!

Well...I did. I used the pkg file downloaded from here. Truth be told, at that time, 2703 was the newest version. I see that now 2721 is out as well. So if you think that's going to make a difference, I'm going to try that. What about that FakeSMC.kext? Is it ok that I copied it into S/L/E ? Is there something else that could cause this issue? Do I need to add some boot flags in order to be able to boot? Cause I don't need anything when booting from USB stick (but it's true that I edited the config.plist and added the following lines at the bottom of the file):

<key>Arguments</key>
<string>kext-dev-mode=1</string>

Do I still need that? Should I add that into the OS as well?

 

I'm sorry if my questions sound stupid. I'm still learning a lot from you, guys. Mac is something new for me. I'm not familiar with many things. But I'm learning. :) So please, bear with me for a while. :)

 

Also, guys, I wanted to ask you about the Apple logo on boot. Isn't there supposed to be one? Cause I didn't see any... It's not a big deal. The loading bar alone is ok. But I was just wondering.

Share this post


Link to post
Share on other sites

Not good idea, isn't it?

35:311  0:009   Table: SSDT  SataTabl  877 dropped
35:320  0:009   Table: SSDT  SaSsdt   13537 dropped

If you have a problem of patching AppleTyMCE the I see no debug messages like

DBG_RT("\nAnyKextPatch %d: driverAddr = %x, driverSize = %x\nAnyKext = %a\n",

so can't say it occured.

Set

	<key>KernelAndKextPatches</key>
	<dict>
		<key>Debug</key>
		<true/>

And see messages on the screen. Debug.log is not possible here.

 

I may propose you just remove the kext. It is not needed.

Use official installer!

True, it's not supposed to drop any tables, but still does. How can does happen? The config.plist doesn't have the entry droptables.

Share this post


Link to post
Share on other sites

Regarding AppleTyMCEDrivers.kext, I also have problem with that one. I would like to keep the .kext because that would mean that i have successfully patched AppleTyMCE kext and that would give me clean system with future updates. Clover should take care off all anomalies of running Hackintosh. So, my problem is that with clover enabled patch for AppleTyMCE boot hangs on: AppleTyMCEDriver::start coreVIDPID.. without patch it is Kernel Panic. I have searched for solution but could not find one. Some say that it is GPU fault ?.

 

My system: 

Mb..asus rampage III gene

CPU...QQ3Q (it is XEON x56xx Enginering Sample) i need to set TYPE=0x501 to get XEON 6 core...without unknown type.

Clover...latest 2722

GPU...GTX650 it is working without graphic enabler...native.

 

Darvin Dumper dump:

https://www.sendspace.com/file/ps71kk

 

bootlog:

https://www.sendspace.com/file/5r1k9c

 

Is there a solution ???

Share this post


Link to post
Share on other sites

I have tried another USB drive, a new config.plist which should work and solves the DropTables problem.

However, still no boot.

0:100  0:100  MemLog inited, TSC freq: 3499989071
0:100  0:000  
0:100  0:000  Now is 17.6.2014,  18:10:24 (GMT+2047)
0:100  0:000  Starting Clover rev 2721 on American Megatrends EFI
0:100  0:000  SelfDevicePath=PciRoot(0x0)\Pci(0x1D,0x0)\USB(0x1,0x0)\USB(0x2,0x0)\HD(1,GPT,EDE86EB9-A484-43B1-A598-E9E5A946C833,0x800,0x392000) @C5ECE498
0:100  0:000  SelfDirPath = \EFI\BOOT
0:103  0:002  UnicodeCollation Status=Success
0:103  0:000  Total Memory Slots Count = 4
0:103  0:000  Type 17 Index = 0
0:103  0:000  SmbiosTable.Type17->Speed = 1600
0:103  0:000  SmbiosTable.Type17->Size = 8192
0:103  0:000  Type 17 Index = 1
0:103  0:000  SmbiosTable.Type17->Speed = 1600
0:103  0:000  SmbiosTable.Type17->Size = 8192
0:103  0:000  Type 17 Index = 2
0:103  0:000  Ignoring insane frequency value 0MHz
0:103  0:000  SmbiosTable.Type17->Speed = 0
0:103  0:000  SmbiosTable.Type17->Size = 0
0:103  0:000  Type 17 Index = 3
0:103  0:000  Ignoring insane frequency value 0MHz
0:103  0:000  SmbiosTable.Type17->Speed = 0
0:103  0:000  SmbiosTable.Type17->Size = 0
0:103  0:000  Boot status=0
0:103  0:000  Clover revision: 2721  running on All Series
0:103  0:000  ... with board MAXIMUS VI GENE
0:103  0:000  Clover load options size = 4 bytes
0:124  0:021  Using OEM config.plist at path: EFI\CLOVER\OEM\MAXIMUS VI GENE\UEFI\config.plist
0:125  0:000  EFI\CLOVER\OEM\MAXIMUS VI GENE\UEFI\config.plist loaded: Success
0:128  0:003  Loading early settings
0:128  0:000  timeout set to 5
0:129  0:000  Default theme: Mavs Style
1:544  1:415  LoadDrivers() start
1:570  0:026  Loading FSInject-64.efi
1:591  0:020  Loading OsxFatBinaryDrv-64.efi
1:614  0:022  Loading VBoxHfs-64.efi
1:636  0:021   - driver needs connecting
1:651  0:014  1 drivers needs connecting ...
1:666  0:015  PlatformDriverOverrideProtocol not found. Installing ... Success
1:697  0:030  Searching for invalid DiskIo BY_DRIVER connects: not found, all ok
1:855  0:157  LoadDrivers() end
1:870  0:015  SetMaxResolution: found best mode 0: 2560x1440 - already set
1:919  0:048  Console modes reported: 4, available modes:
1:934  0:015    Mode 1: 80x25 (current mode)
1:950  0:015    Mode 2: 80x50
1:965  0:015    Mode 3: 100x31
1:981  0:015    Mode 4: 320x75
1:996  0:015  reinit: self device path=PciRoot(0x0)\Pci(0x1D,0x0)\USB(0x1,0x0)\USB(0x2,0x0)\HD(1,GPT,EDE86EB9-A484-43B1-A598-E9E5A946C833,0x800,0x392000)
2:012  0:015  new SelfHandle=C5ECE498
2:032  0:020  CPU Vendor = 756E6547 Model=306C3
2:045  0:012  The CPU supported turbo
2:061  0:015  BrandString = Intel(R) Core(TM) i7-4770K CPU @ 3.50GHz
2:080  0:019  MSR 0xE2 before patch 00000000
2:103  0:022  MSR 0xE4              00000000
2:122  0:018  MSR 0xCE              00080838_F3012300
2:140  0:018  non-usable FLEX_RATIO = F0000
2:159  0:018  corrected FLEX_RATIO = E0000
2:177  0:018  MSR 0x1B0             00000000
2:195  0:018  FSBFrequency=100MHz
2:214  0:018  Corrected FSBFrequency=100MHz
2:232  0:018  Vendor/Model/Stepping: 0x756E6547/0x3C/0x3
2:251  0:018  Family/ExtFamily: 0x6/0x0
2:274  0:023  MaxDiv/MinDiv: 35.0/8
2:294  0:019  Turbo: 39/39/39/39
2:310  0:016  Features: 0xBFEBFBFF
2:330  0:019  Threads: 8
2:347  0:016  Cores: 4
2:367  0:019  FSB: 100 MHz
2:383  0:016  CPU: 3505 MHz
2:403  0:019  TSC: 3505 MHz
2:420  0:016  PIS: 400 MHz
2:440  0:019  PCI (00|00:00.00) : 8086 0C00 class=060000
2:456  0:016  PCI (00|00:01.00) : 8086 0C01 class=060400
2:476  0:019  PCI (00|01:00.00) : 10DE 1004 class=030000
2:493  0:016  Found NVidia model=nVidia GeForce GTX 780
2:513  0:019  PCI (00|01:00.01) : 10DE 0E1A class=040300
2:532  0:019  PCI (00|00:02.00) : 8086 0412 class=038000
2:552  0:019  PCI (00|00:03.00) : 8086 0C0C class=040300
2:569  0:016  PCI (00|00:14.00) : 8086 8C31 class=0C0330
2:588  0:019  PCI (00|00:16.00) : 8086 8C3A class=078000
2:605  0:016  PCI (00|00:16.01) : FFFF FFFF class=FFFFFF
2:625  0:019  PCI (00|00:19.00) : 8086 153B class=020000
2:642  0:016  PCI (00|00:1A.00) : 8086 8C2D class=0C0320
2:661  0:019  PCI (00|00:1B.00) : 8086 8C20 class=040300
2:695  0:033  PCI (00|00:1C.00) : 8086 8C10 class=060400
2:715  0:019  PCI (00|00:1C.03) : 8086 8C16 class=060400
2:732  0:016  PCI (00|03:00.00) : 1B21 0612 class=010601
2:752  0:019  PCI (00|00:1C.04) : 8086 8C18 class=060400
2:768  0:016  PCI (00|04:00.00) : 14E4 43A0 class=028000
2:788  0:019  PCI (00|00:1D.00) : 8086 8C26 class=0C0320
2:805  0:016  PCI (00|00:1F.00) : 8086 8C44 class=060100
2:825  0:019  PCI (00|00:1F.03) : 8086 8C22 class=0C0500
2:842  0:016  PCI (00|00:1F.06) : FFFF FFFF class=FFFFFF
2:864  0:022  ScanSPD() start
2:881  0:016  SMBus CmdReg: 0x3
2:901  0:019  Scanning SMBus [8086:8C22], mmio: 0xF7C39004, ioport: 0xF040, hostc: 0x1
2:948  0:047  SPD[0]: Type 11 @0x50 
2:976  0:028  Using XMP Profile1 instead of standard frequency 1333MHz
2:993  0:016  DDR speed 1600MHz 
3:013  0:019  Slot: 0 Type 24 8192MB 1600MHz Vendor=Crucial Technology PartNo=BLT8G3D1608ET3LX0. SerialNo=0A09000408060A03 
3:044  0:031  SPD[1]: Type 11 @0x51 
3:072  0:028  Using XMP Profile1 instead of standard frequency 1333MHz
3:091  0:019  DDR speed 1600MHz 
3:111  0:019  Slot: 1 Type 24 8192MB 1600MHz Vendor=Crucial Technology PartNo=BLT8G3D1608ET3LX0. SerialNo=0A09000408070105 
3:260  0:149  ScanSPD() end
3:280  0:019  Get Acpi Tables List from RSDT:
3:317  0:036   Found table: FACP  A M I len=132
3:333  0:016   Found table: APIC  A M I len=146
3:353  0:019   Found table: FPDT  A M I len=68
3:370  0:016   Found table: LPIT  A M I len=92
3:390  0:019   Found table: SSDT  Cpu0Ist len=1337
3:409  0:019   Found table: SSDT  CpuPm len=2776
3:429  0:019   Found table: MCFG  A M I len=60
3:446  0:016   Found table: HPET  A M I len=56
3:465  0:019   Found table: SSDT  SataTabl len=877
3:482  0:016   Found table: SSDT  SaSsdt  len=13537
3:502  0:019   Found table: BGRT  A M I len=56
3:519  0:016  Calibrated TSC frequency =3499989071 =3499MHz
3:539  0:019  Loading main settings
3:555  0:016  KextsToPatch: 2 requested
3:575  0:019  KextToPatch 0: IOAHCIBlockStorage Kext bin patch, data len: 10
3:651  0:075  KextToPatch 1: AppleTyMCEDriver Kext bin patch, data len: 24
3:724  0:073  Oem smbios.plist not found at path: EFI\CLOVER\OEM\MAXIMUS VI GENE\UEFI\smbios.plist
3:740  0:016  smbios.plist not found, not overriding config.plist
3:760  0:019  found 6 volumes with blockIO
3:777  0:016   0. Volume:
3:797  0:019    PciRoot(0x0)\Pci(0x1D,0x0)\USB(0x1,0x0)\USB(0x2,0x0)
3:815  0:018    USB volume
3:835  0:019    USB volume
3:852  0:016    Volume 'Whole Disc Boot', LegacyOS '', LegacyIcon(s) 'legacy', GUID = <null guid>
3:874  0:022   1. Volume:
3:891  0:016    PciRoot(0x0)\Pci(0x1D,0x0)\USB(0x1,0x0)\USB(0x2,0x0)\HD(1,GPT,EDE86EB9-A484-43B1-A598-E9E5A946C833,0x800,0x392000)
3:916  0:025    Result of bootcode detection: bootable <null string> (<null string>)
3:930  0:014    USB volume
3:950  0:019    USB volume
3:972  0:021    Volume 'BOOTER', LegacyOS '', LegacyIcon(s) '<null string>', GUID = EDE86EB9-A484-43B1-A598-E9E5A946C833
3:989  0:017    This is SelfVolume !!
4:006  0:016   2. Volume:
4:028  0:022    PciRoot(0x0)\Pci(0x1C,0x3)\Pci(0x0,0x0)\Sata(0x1,0xFFFF,0x0)
4:046  0:017    Volume 'Whole Disc Boot', LegacyOS '', LegacyIcon(s) 'legacy', GUID = <null guid>
4:066  0:019   3. Volume:
4:082  0:016    PciRoot(0x0)\Pci(0x1C,0x3)\Pci(0x0,0x0)\Sata(0x1,0xFFFF,0x0)\HD(1,GPT,F6FC26D9-7296-4388-BC41-9F1C43BBC31E,0x28,0x64000)
4:103  0:020    Result of bootcode detection: bootable <null string> (<null string>)
4:125  0:022    Volume 'EFI', LegacyOS '', LegacyIcon(s) '<null string>', GUID = F6FC26D9-7296-4388-BC41-9F1C43BBC31E
4:147  0:022   4. Volume:
4:164  0:016    PciRoot(0x0)\Pci(0x1C,0x3)\Pci(0x0,0x0)\Sata(0x1,0xFFFF,0x0)\HD(2,GPT,5F539792-05C0-418B-8E42-873972467708,0x64028,0x3B847340)
4:482  0:318    Volume 'Macintosh SSD', LegacyOS '', LegacyIcon(s) '<null string>', GUID = 5F539792-05C0-418B-8E42-873972467708
4:500  0:017   5. Volume:
4:849  0:349    PciRoot(0x0)\Pci(0x1C,0x3)\Pci(0x0,0x0)\Sata(0x1,0xFFFF,0x0)\HD(3,GPT,D6356AA1-D7E8-42BB-AFAA-9CD232C29C7A,0x3B8AB368,0x135F20)
4:883  0:033    Volume 'Recovery HD', LegacyOS '', LegacyIcon(s) '<null string>', GUID = D6356AA1-D7E8-42BB-AFAA-9CD232C29C7A
4:899  0:015  Invalidating BuiltinIcons...
4:915  0:015  no themes available, using embedded
4:931  0:015  Font 0 prepared WxH=7x12 CharWidth=7
4:947  0:016  Choosing theme <null string>
4:963  0:016  Custom entries start
4:979  0:015  Custom entries finish
4:995  0:015  Scanning loaders...
5:011  0:015   0: 'Whole Disc Boot' no file system
5:043  0:031   1: 'BOOTER'
5:075  0:032  skipped because path `PciRoot(0x0)\Pci(0x1D,0x0)\USB(0x1,0x0)\USB(0x2,0x0)\HD(1,GPT,EDE86EB9-A484-43B1-A598-E9E5A946C833,0x800,0x392000)\EFI\BOOT\BOOTX64.efi` is self path!
5:091  0:015   2: 'Whole Disc Boot' no file system
5:123  0:031   3: 'EFI'
5:155  0:032   4: 'Macintosh SSD'
5:194  0:039  Check if volume Is Hibernated:
5:210  0:015  Check sleep image 'by signature':
5:233  0:022  read prefs \Library\Preferences\SystemConfiguration\com.apple.PowerManagement.plist status=Not Found
5:251  0:018  using default sleep image name = \private\var\vm\sleepimage
5:272  0:021  Reading first 512 bytes of sleepimage ...
5:289  0:016   OurBlockIoRead: Lba=1AE41D8, Offset=35C83B000 (BlockSize=512)
5:305  0:015   sig lion: 0
5:321  0:016   sig snow: 0
5:337  0:015   no valid sleep image offset was found
5:353  0:015  Reading completed -> Success
5:374  0:021   sleepimage offset could not be acquired
5:390  0:015   hibernated: no - sign
5:408  0:017  found PciRoot(0x0)\Pci(0x1C,0x3)\Pci(0x0,0x0)\Sata(0x1,0xFFFF,0x0)\HD(2,GPT,5F539792-05C0-418B-8E42-873972467708,0x64028,0x3B847340)\System\Library\CoreServices\boot.efi
5:427  0:019   5: 'Recovery HD'
5:462  0:035  found PciRoot(0x0)\Pci(0x1C,0x3)\Pci(0x0,0x0)\Sata(0x1,0xFFFF,0x0)\HD(3,GPT,D6356AA1-D7E8-42BB-AFAA-9CD232C29C7A,0x3B8AB368,0x135F20)\com.apple.recovery.boot\boot.efi
5:479  0:016  Custom legacy start
5:494  0:015  Custom legacy end
5:510  0:015  Scanning legacy ...
5:525  0:015   0: 'Whole Disc Boot' (legacy) not legacy
5:556  0:031   1: 'BOOTER' (<null string>) not legacy
5:589  0:032   2: 'Whole Disc Boot' (legacy) not legacy
5:620  0:031   3: 'EFI' (<null string>) not legacy
5:651  0:031   4: 'Macintosh SSD' (<null string>) not legacy
5:682  0:031   5: 'Recovery HD' (<null string>) not legacy
5:713  0:030  Custom tool start
5:729  0:015  Custom tool end
5:754  0:025  found tool \EFI\CLOVER\tools\Shell64U.efi
5:768  0:014  Checking EFI partition Volume 3 for Clover
5:785  0:016  GetEfiBootDeviceFromNvram: efi-boot-device-data not found
5:818  0:032  EfiBootVolume not found
5:842  0:024  Default boot entry not found
5:860  0:017  DefaultIndex=-1 and MainMenu.EntryCount=7
5:898  0:037  Found Mouse device:
5:916  0:017  GUI ready
15:370  9:454  StartLoader() start
15:388  0:018  Finally: Bus=99999kHz CPU=3499MHz
15:409  0:021  Loading boot.efi
15:510  0:101  insert table 9 for dev 0:0
15:531  0:020  insert table 9 for dev 19:0
15:548  0:017  insert table 9 for dev 0:0
15:569  0:021  Trusting SMBIOS...
15:587  0:017  Channels: 2
15:612  0:024  Interleave: 0 2 1 3 4 6 5 7 8 10 9 11 12 14 13 15 16 18 17 19 20 22 21 23
16:116  0:504   partNum=BLT8G3D1608ET3LX0.
16:135  0:018  SMBIOS Type 17 Index = 0 => 0 0:
16:154  0:018   DIMM1 1600MHz 8192MB
16:173  0:018  mTotalSystemMemory = 8192
16:191  0:018  SMBIOS Type 17 Index = 1 => 2 2:
16:210  0:018   DIMM2 EMPTY
16:229  0:018   partNum=BLT8G3D1608ET3LX0.
16:248  0:019  SMBIOS Type 17 Index = 2 => 1 1:
16:268  0:019   DIMM3 1600MHz 8192MB
16:286  0:018  mTotalSystemMemory = 16384
16:308  0:021  SMBIOS Type 17 Index = 3 => 3 3:
16:327  0:018   DIMM4 EMPTY
16:345  0:018  NumberOfMemoryDevices = 4
16:364  0:018  Type20[0]->End = 0x7FFFFF, Type17[0] = 0x2000
16:383  0:018  Type20[1]->End = 0xFFFFFF, Type17[2] = 0x6000
16:402  0:018  Table 131 is present, CPUType=31
16:420  0:018  Change to: 705
16:439  0:019  RSDT 0xC862D028
16:458  0:018  FADT from RSDT: 0xC862D110
16:477  0:018  XSDT 0xC862D080
16:496  0:018  FADT from XSDT: 0xC863B630
16:515  0:018  Xsdt reallocation done
16:551  0:036  old FADT length=10C
16:570  0:018  Found OperationRegion(GNVS, SystemMemory, C887EC18, ...)
16:589  0:018  Found OperationRegion(MCHT, SystemMemory, FED10000, ...)
16:607  0:018  Found OperationRegion(RCRB, SystemMemory, FED1C000, ...)
16:626  0:018  Found OperationRegion(XHCP, SystemMemory, 0, ...)
16:645  0:018  Found OperationRegion(MCA1, SystemMemory, F7FE0000, ...)
16:946  0:301  Found OperationRegion(MCA1, SystemMemory, F7FE0000, ...)
16:965  0:018  Found OperationRegion(CPSB, SystemMemory, C8626E18, ...)
16:986  0:021  Found OperationRegion(MBAR, SystemMemory, 0, ...)
17:005  0:018  Found OperationRegion(RAMW, SystemMemory, C8869018, ...)
17:024  0:018  Found OperationRegion(TMMB, SystemMemory, FED40000, ...)
17:064  0:040  DSDT len = 0xE493 new len = 0x10125
17:100  0:036  Apply DsdtFixMask=0x00000000 old way
17:119  0:018     drop _DSM mask=0xFFFF
17:138  0:018  ========= Auto patch DSDT Starting ========
17:157  0:018  VideoCard devID=0x100410DE
17:178  0:021  DisplayADR1[0] = 0x10000, DisplayADR2[0] = 0x0
17:197  0:018  Display 0 is  notPCIE
17:216  0:018  USBADR[0] = 0x140000 and PCIe = 0xFFFE
17:234  0:018  USBADR[1] = 0x1A0000 and PCIe = 0xFFFE
17:360  0:125  Found Airport BCM at 0x1C0004, 0x0
17:396  0:036  USBADR[2] = 0x1D0000 and PCIe = 0xFFFE
17:415  0:018  first CPU found at 84C8 offset 84CC
17:434  0:018  score candidate at 84C4
17:453  0:018  score inserted in acpi_cpu_score _PR_
17:472  0:018  Found ACPI CPU: CPU0 And CPU1 And CPU2 And CPU3 And CPU4 And CPU5 And CPU6 And CPU7 
  within the score: _PR_
17:644  0:172  Found PCIROOTUID = 0
17:663  0:018  ========= Auto patch DSDT Finished ========
17:682  0:018  Patch table: SSDT  Cpu0Ist
17:701  0:018   SSDT len = 0x539
17:719  0:018  Patch table: SSDT  CpuPm
17:738  0:018   SSDT len = 0xAD8
18:085  0:347  Patch table: SSDT  SataTabl
18:102  0:016   SSDT len = 0x36D
18:116  0:013  Patch table: SSDT  SaSsdt 
18:133  0:016   SSDT len = 0x34E1
18:147  0:013  Drop tables from Xsdt, SIGN=XXXX TableID= Length=0
18:166  0:019   Xsdt has tables count=11 
18:180  0:013  corrected XSDT length=124
18:196  0:016  Inserting SSDT.aml from EFI\CLOVER\OEM\MAXIMUS VI GENE\UEFI\ACPI\patched ... Success
18:229  0:033   CPUBase=0 and ApicCPUBase=1 ApicCPUNum=8
18:243  0:013  Maximum control=23
18:260  0:016  Turbo control=27
18:274  0:014  P-States: min 0x8, max 0x27
18:291  0:017  SSDT with CPU P-States generated successfully
18:305  0:013  SSDT with CPU C-States generated successfully
18:324  0:019  EdidDiscovered size=256
18:338  0:013  NVidia GFX injection not set
18:355  0:016  HDA Controller [8086:0C0C] :: PciRoot(0x0)\Pci(0x3,0x0) => codec not detected
18:492  0:137  LAN Controller [8086:153B] :: PciRoot(0x0)\Pci(0x19,0x0)
18:506  0:013  HDA Controller [8086:8C20] :: PciRoot(0x0)\Pci(0x1B,0x0) => codec not detected
18:643  0:137  stringlength = 860
18:660  0:016  CurrentMode: Width=2560 Height=1440
18:674  0:013  FSInjection: skipping kext injection (not requested)
18:726  0:052  MSR 0x1B0   set to        00000000
18:742  0:016  SetStartupDiskVolume:
18:759  0:016    * Volume: 'Macintosh SSD'
18:780  0:020    * LoaderPath: '<null string>'
18:796  0:016    * DevPath: Macintosh SSD
18:810  0:013    * GUID = 5F539792-05C0-418B-8E42-873972467708
18:835  0:024    * efi-boot-device: <array><dict><key>IOMatch</key><dict><key>IOProviderClass</key><string>IOMedia</string><key>IOPropertyMatch</key><dict><key>UUID</key><string>5F539792-05C0-418B-8E42-873972467708</string></dict></dict></dict></array>
18:859  0:024  Closing log
0:100  0:100  MemLog inited, TSC freq: 3500000671
0:100  0:000  
0:100  0:000  Now is 17.6.2014,  18:15:18 (GMT+2047)
0:100  0:000  Starting Clover rev 2721 on American Megatrends EFI
0:100  0:000  SelfDevicePath=PciRoot(0x0)\Pci(0x1D,0x0)\USB(0x1,0x0)\USB(0x2,0x0)\HD(1,GPT,EDE86EB9-A484-43B1-A598-E9E5A946C833,0x800,0x392000) @C5ECE518
0:100  0:000  SelfDirPath = \EFI\BOOT
0:103  0:002  UnicodeCollation Status=Success
0:103  0:000  Total Memory Slots Count = 4
0:103  0:000  Type 17 Index = 0
0:103  0:000  SmbiosTable.Type17->Speed = 1600
0:103  0:000  SmbiosTable.Type17->Size = 8192
0:103  0:000  Type 17 Index = 1
0:103  0:000  SmbiosTable.Type17->Speed = 1600
0:103  0:000  SmbiosTable.Type17->Size = 8192
0:103  0:000  Type 17 Index = 2
0:103  0:000  Ignoring insane frequency value 0MHz
0:103  0:000  SmbiosTable.Type17->Speed = 0
0:103  0:000  SmbiosTable.Type17->Size = 0
0:103  0:000  Type 17 Index = 3
0:103  0:000  Ignoring insane frequency value 0MHz
0:103  0:000  SmbiosTable.Type17->Speed = 0
0:103  0:000  SmbiosTable.Type17->Size = 0
0:103  0:000  Boot status=0
0:103  0:000  Clover revision: 2721  running on All Series
0:103  0:000  ... with board MAXIMUS VI GENE
0:103  0:000  Clover load options size = 4 bytes
0:124  0:021  Using OEM config.plist at path: EFI\CLOVER\OEM\MAXIMUS VI GENE\UEFI\config.plist
0:124  0:000  EFI\CLOVER\OEM\MAXIMUS VI GENE\UEFI\config.plist loaded: Success
0:131  0:006  Loading early settings
0:131  0:000  timeout set to 5
0:131  0:000  Default theme: Mavs Style
1:846  1:715  LoadDrivers() start
2:152  0:306  Loading FSInject-64.efi
2:177  0:024  Loading OsxFatBinaryDrv-64.efi
2:201  0:023  Loading VBoxHfs-64.efi
2:227  0:025   - driver needs connecting
2:244  0:017  Loading EmuVariableUefi-64.efi
2:271  0:026  EmuVariableUefi Initialize: VariableCommonInitialize = Success, orig services stored, install gEmuVariableControlProtocolGuid = Success
2:347  0:075  Loading OsxAptioFixDrv-64.efi
2:374  0:027  1 drivers needs connecting ...
2:392  0:017  PlatformDriverOverrideProtocol not found. Installing ... Success
2:431  0:038  Searching for invalid DiskIo BY_DRIVER connects: not found, all ok
2:584  0:153  LoadDrivers() end
2:603  0:019  EmuVariable InstallEmulation: orig vars copied, emu.var.services installed, CreateEvent VirtualAddressChange = Success, CreateEvent ExitBootServices = Success, set Status=Success
2:725  0:121  SetMaxResolution: found best mode 0: 2560x1440 - already set
2:782  0:057  Console modes reported: 4, available modes:
2:804  0:021    Mode 1: 80x25 (current mode)
2:824  0:019    Mode 2: 80x50
2:843  0:019    Mode 3: 100x31
2:862  0:019    Mode 4: 320x75
2:881  0:019  reinit: self device path=PciRoot(0x0)\Pci(0x1D,0x0)\USB(0x1,0x0)\USB(0x2,0x0)\HD(1,GPT,EDE86EB9-A484-43B1-A598-E9E5A946C833,0x800,0x392000)
2:900  0:019  new SelfHandle=C5ECE518
2:923  0:023  CPU Vendor = 756E6547 Model=306C3
2:941  0:017  The CPU supported turbo
2:960  0:019  BrandString = Intel(R) Core(TM) i7-4770K CPU @ 3.50GHz
2:982  0:021  MSR 0xE2 before patch 00000000
3:001  0:019  MSR 0xE4              00000000
3:020  0:019  MSR 0xCE              00080838_F3012300
3:040  0:019  non-usable FLEX_RATIO = F0000
3:059  0:019  corrected FLEX_RATIO = E0000
3:078  0:019  MSR 0x1B0             00000000
3:097  0:019  FSBFrequency=100MHz
3:116  0:019  Corrected FSBFrequency=100MHz
3:136  0:019  Vendor/Model/Stepping: 0x756E6547/0x3C/0x3
3:155  0:019  Family/ExtFamily: 0x6/0x0
3:174  0:019  MaxDiv/MinDiv: 35.0/8
3:197  0:023  Turbo: 39/39/39/39
3:218  0:020  Features: 0xBFEBFBFF
3:235  0:017  Threads: 8
3:256  0:020  Cores: 4
3:273  0:017  FSB: 100 MHz
3:294  0:020  CPU: 3504 MHz
3:311  0:017  TSC: 3504 MHz
3:332  0:020  PIS: 400 MHz
3:349  0:017  PCI (00|00:00.00) : 8086 0C00 class=060000
3:370  0:020  PCI (00|00:01.00) : 8086 0C01 class=060400
3:402  0:031  PCI (00|01:00.00) : 10DE 1004 class=030000
3:422  0:020  Found NVidia model=nVidia GeForce GTX 780
3:440  0:017  PCI (00|01:00.01) : 10DE 0E1A class=040300
3:463  0:022  PCI (00|00:02.00) : 8086 0412 class=038000
3:480  0:017  PCI (00|00:03.00) : 8086 0C0C class=040300
3:501  0:020  PCI (00|00:14.00) : 8086 8C31 class=0C0330
3:518  0:017  PCI (00|00:16.00) : 8086 8C3A class=078000
3:539  0:020  PCI (00|00:16.01) : FFFF FFFF class=FFFFFF
3:556  0:017  PCI (00|00:19.00) : 8086 153B class=020000
3:577  0:020  PCI (00|00:1A.00) : 8086 8C2D class=0C0320
3:594  0:017  PCI (00|00:1B.00) : 8086 8C20 class=040300
3:615  0:020  PCI (00|00:1C.00) : 8086 8C10 class=060400
3:930  0:314  PCI (00|00:1C.03) : 8086 8C16 class=060400
3:951  0:020  PCI (00|03:00.00) : 1B21 0612 class=010601
3:968  0:017  PCI (00|00:1C.04) : 8086 8C18 class=060400
3:989  0:020  PCI (00|04:00.00) : 14E4 43A0 class=028000
4:006  0:017  PCI (00|00:1D.00) : 8086 8C26 class=0C0320
4:027  0:020  PCI (00|00:1F.00) : 8086 8C44 class=060100
4:044  0:017  PCI (00|00:1F.03) : 8086 8C22 class=0C0500
4:065  0:020  PCI (00|00:1F.06) : FFFF FFFF class=FFFFFF
4:083  0:017  ScanSPD() start
4:106  0:023  SMBus CmdReg: 0x3
4:124  0:017  Scanning SMBus [8086:8C22], mmio: 0xF7C39004, ioport: 0xF040, hostc: 0x1
4:158  0:034  SPD[0]: Type 11 @0x50 
4:184  0:025  Using XMP Profile1 instead of standard frequency 1333MHz
4:205  0:020  DDR speed 1600MHz 
4:223  0:017  Slot: 0 Type 24 8192MB 1600MHz Vendor=Crucial Technology PartNo=BLT8G3D1608ET3LX0. SerialNo=0A09000408060A03 
4:257  0:034  SPD[1]: Type 11 @0x51 
4:283  0:026  Using XMP Profile1 instead of standard frequency 1333MHz
4:307  0:023  DDR speed 1600MHz 
4:324  0:017  Slot: 1 Type 24 8192MB 1600MHz Vendor=Crucial Technology PartNo=BLT8G3D1608ET3LX0. SerialNo=0A09000408070105 
4:477  0:152  ScanSPD() end
4:495  0:017  Get Acpi Tables List from RSDT:
4:533  0:038   Found table: FACP  A M I len=132
4:554  0:020   Found table: APIC  A M I len=146
4:571  0:017   Found table: FPDT  A M I len=68
4:592  0:020   Found table: LPIT  A M I len=92
4:609  0:017   Found table: SSDT  Cpu0Ist len=1337
4:630  0:020   Found table: SSDT  CpuPm len=2776
4:650  0:020   Found table: MCFG  A M I len=60
4:671  0:021   Found table: HPET  A M I len=56
4:689  0:017   Found table: SSDT  SataTabl len=877
4:709  0:020   Found table: SSDT  SaSsdt  len=13537
4:727  0:017   Found table: BGRT  A M I len=56
4:748  0:020  Calibrated TSC frequency =3500000671 =3500MHz
4:765  0:017  Loading main settings
4:786  0:020  KextsToPatch: 2 requested
4:803  0:017  KextToPatch 0: IOAHCIBlockStorage Kext bin patch, data len: 10
4:879  0:076  KextToPatch 1: AppleTyMCEDriver Kext bin patch, data len: 24
4:958  0:078  Oem smbios.plist not found at path: EFI\CLOVER\OEM\MAXIMUS VI GENE\UEFI\smbios.plist
4:993  0:035  smbios.plist not found, not overriding config.plist
5:011  0:017  found 6 volumes with blockIO
5:031  0:020   0. Volume:
5:049  0:017    PciRoot(0x0)\Pci(0x1D,0x0)\USB(0x1,0x0)\USB(0x2,0x0)
5:071  0:022    USB volume
5:089  0:017    USB volume
5:109  0:020    Volume 'Whole Disc Boot', LegacyOS '', LegacyIcon(s) 'legacy', GUID = <null guid>
5:129  0:020   1. Volume:
5:150  0:020    PciRoot(0x0)\Pci(0x1D,0x0)\USB(0x1,0x0)\USB(0x2,0x0)\HD(1,GPT,EDE86EB9-A484-43B1-A598-E9E5A946C833,0x800,0x392000)
5:172  0:021    Result of bootcode detection: bootable <null string> (<null string>)
5:191  0:019    USB volume
5:208  0:017    USB volume
5:790  0:582    Volume 'BOOTER', LegacyOS '', LegacyIcon(s) '<null string>', GUID = EDE86EB9-A484-43B1-A598-E9E5A946C833
5:806  0:015    This is SelfVolume !!
5:827  0:020   2. Volume:
5:844  0:017    PciRoot(0x0)\Pci(0x1C,0x3)\Pci(0x0,0x0)\Sata(0x1,0xFFFF,0x0)
5:868  0:023    Volume 'Whole Disc Boot', LegacyOS '', LegacyIcon(s) 'legacy', GUID = <null guid>
5:885  0:017   3. Volume:
5:905  0:020    PciRoot(0x0)\Pci(0x1C,0x3)\Pci(0x0,0x0)\Sata(0x1,0xFFFF,0x0)\HD(1,GPT,F6FC26D9-7296-4388-BC41-9F1C43BBC31E,0x28,0x64000)
5:923  0:017    Result of bootcode detection: bootable <null string> (<null string>)
5:949  0:025    Volume 'EFI', LegacyOS '', LegacyIcon(s) '<null string>', GUID = F6FC26D9-7296-4388-BC41-9F1C43BBC31E
5:969  0:019   4. Volume:
5:989  0:020    PciRoot(0x0)\Pci(0x1C,0x3)\Pci(0x0,0x0)\Sata(0x1,0xFFFF,0x0)\HD(2,GPT,5F539792-05C0-418B-8E42-873972467708,0x64028,0x3B847340)
6:007  0:017    Volume 'Macintosh SSD', LegacyOS '', LegacyIcon(s) '<null string>', GUID = 5F539792-05C0-418B-8E42-873972467708
6:027  0:020   5. Volume:
6:045  0:017    PciRoot(0x0)\Pci(0x1C,0x3)\Pci(0x0,0x0)\Sata(0x1,0xFFFF,0x0)\HD(3,GPT,D6356AA1-D7E8-42BB-AFAA-9CD232C29C7A,0x3B8AB368,0x135F20)
6:066  0:021    Volume 'Recovery HD', LegacyOS '', LegacyIcon(s) '<null string>', GUID = D6356AA1-D7E8-42BB-AFAA-9CD232C29C7A
6:101  0:035  Searching volumes for latest nvram.plist ...
6:138  0:037    1. Volume 'BOOTER', GUID = EDE86EB9-A484-43B1-A598-E9E5A946C833 - no nvram.plist - skipping!
6:176  0:037    3. Volume 'EFI', GUID = F6FC26D9-7296-4388-BC41-9F1C43BBC31E - no nvram.plist - skipping!
6:214  0:037    4. Volume 'Macintosh SSD', GUID = 5F539792-05C0-418B-8E42-873972467708 - no nvram.plist - skipping!
6:254  0:040    5. Volume 'Recovery HD', GUID = D6356AA1-D7E8-42BB-AFAA-9CD232C29C7A - no nvram.plist - skipping!
6:295  0:040   nvram.plist not found!
6:315  0:020  PutNvramPlistToRtVars: nvram.plist not found
6:333  0:017  Invalidating BuiltinIcons...
6:353  0:020  no themes available, using embedded
6:370  0:017  Font 0 prepared WxH=7x12 CharWidth=7
6:391  0:020  Choosing theme <null string>
6:408  0:017  Custom entries start
6:428  0:020  Custom entries finish
6:446  0:017  Scanning loaders...
6:466  0:020   0: 'Whole Disc Boot' no file system
6:506  0:040   1: 'BOOTER'
6:544  0:037  skipped because path `PciRoot(0x0)\Pci(0x1D,0x0)\USB(0x1,0x0)\USB(0x2,0x0)\HD(1,GPT,EDE86EB9-A484-43B1-A598-E9E5A946C833,0x800,0x392000)\EFI\BOOT\BOOTX64.efi` is self path!
6:562  0:017   2: 'Whole Disc Boot' no file system
6:599  0:037   3: 'EFI'
6:637  0:038   4: 'Macintosh SSD'
6:695  0:057  Check if volume Is Hibernated:
6:715  0:020  Check sleep image 'by signature':
6:739  0:023  read prefs \Library\Preferences\SystemConfiguration\com.apple.PowerManagement.plist status=Not Found
6:762  0:023  using default sleep image name = \private\var\vm\sleepimage
6:784  0:021  Reading first 512 bytes of sleepimage ...
6:805  0:020   OurBlockIoRead: Lba=1AE41D8, Offset=35C83B000 (BlockSize=512)
6:822  0:017   sig lion: 0
6:842  0:020   sig snow: 0
6:860  0:017   no valid sleep image offset was found
6:880  0:020  Reading completed -> Success
6:898  0:017   sleepimage offset could not be acquired
6:918  0:020   hibernated: no - sign
6:941  0:022  found PciRoot(0x0)\Pci(0x1C,0x3)\Pci(0x0,0x0)\Sata(0x1,0xFFFF,0x0)\HD(2,GPT,5F539792-05C0-418B-8E42-873972467708,0x64028,0x3B847340)\System\Library\CoreServices\boot.efi
6:963  0:022   5: 'Recovery HD'
7:004  0:041  found PciRoot(0x0)\Pci(0x1C,0x3)\Pci(0x0,0x0)\Sata(0x1,0xFFFF,0x0)\HD(3,GPT,D6356AA1-D7E8-42BB-AFAA-9CD232C29C7A,0x3B8AB368,0x135F20)\com.apple.recovery.boot\boot.efi
7:023  0:018  Custom legacy start
7:043  0:020  Custom legacy end
7:060  0:017  Scanning legacy ...
7:084  0:023   0: 'Whole Disc Boot' (legacy) not legacy
7:121  0:037   1: 'BOOTER' (<null string>) not legacy
7:159  0:037   2: 'Whole Disc Boot' (legacy) not legacy
7:197  0:037   3: 'EFI' (<null string>) not legacy
7:235  0:037   4: 'Macintosh SSD' (<null string>) not legacy
7:273  0:037   5: 'Recovery HD' (<null string>) not legacy
7:311  0:037  Custom tool start
7:329  0:017  Custom tool end
7:359  0:030  found tool \EFI\CLOVER\tools\Shell64U.efi
7:375  0:016  Checking EFI partition Volume 3 for Clover
7:401  0:025  EmuVariable InstallEmulation: EFI_ALREADY_STARTED
7:438  0:037  GetEfiBootDeviceFromNvram:
7:476  0:037   efi-boot-device-data: PciRoot(0x0)\Pci(0x1C,0x3)\Pci(0x0,0x0)\Sata(0x1,0xFFFF,0x0)\HD(2,GPT,5F539792-05C0-418B-8E42-873972467708,0x64028,0x3B847340)
7:495  0:018   Volume: 'PciRoot(0x0)\Pci(0x1C,0x3)\Pci(0x0,0x0)\Sata(0x1,0xFFFF,0x0)\HD(2,GPT,5F539792-05C0-418B-8E42-873972467708,0x64028,0x3B847340)'
7:513  0:018   LoaderPath: '<null string>'
7:532  0:018   Guid = 5F539792-05C0-418B-8E42-873972467708
7:553  0:021   volume: partition = PciRoot(0x0)\Pci(0x1C,0x3)\Pci(0x0,0x0)\Sata(0x1,0xFFFF,0x0)\HD(2,GPT,5F539792-05C0-418B-8E42-873972467708,0x64028,0x3B847340)
7:572  0:018   searching for that partition
7:591  0:018    found entry 0. 'Boot Mac OS X from Macintosh SSD', Volume 'Macintosh SSD'
7:609  0:018  Boot redirected to Entry 0. 'Boot Mac OS X from Macintosh SSD'
7:628  0:018  EmuVariable UninstallEmulation: CloseEvent = Success, original var services restored
7:702  0:074  DefaultIndex=0 and MainMenu.EntryCount=7
7:738  0:035  Found Mouse device:
7:757  0:019  GUI ready
14:383  6:625  StartLoader() start
14:402  0:019  Finally: Bus=100000kHz CPU=3500MHz
14:421  0:019  Loading boot.efi
14:524  0:102  EmuVariable InstallEmulation: orig vars copied, emu.var.services installed, CreateEvent VirtualAddressChange = Success, CreateEvent ExitBootServices = Success, set Status=Success
14:658  0:134  insert table 9 for dev 0:0
14:677  0:018  insert table 9 for dev 19:0
14:698  0:021  insert table 9 for dev 0:0
14:717  0:019  Trusting SMBIOS...
14:736  0:018  Channels: 2
14:755  0:018  Interleave: 0 2 1 3 4 6 5 7 8 10 9 11 12 14 13 15 16 18 17 19 20 22 21 23
15:799  1:044   partNum=BLT8G3D1608ET3LX0.
15:818  0:018  SMBIOS Type 17 Index = 0 => 0 0:
15:837  0:018   DIMM1 1600MHz 8192MB
15:856  0:018  mTotalSystemMemory = 8192
15:874  0:018  SMBIOS Type 17 Index = 1 => 2 2:
15:893  0:018   DIMM2 EMPTY
15:912  0:018   partNum=BLT8G3D1608ET3LX0.
15:931  0:018  SMBIOS Type 17 Index = 2 => 1 1:
15:952  0:021   DIMM3 1600MHz 8192MB
15:971  0:018  mTotalSystemMemory = 16384
15:989  0:018  SMBIOS Type 17 Index = 3 => 3 3:
16:008  0:018   DIMM4 EMPTY
16:027  0:018  NumberOfMemoryDevices = 4
16:046  0:018  Type20[0]->End = 0x7FFFFF, Type17[0] = 0x2000
16:064  0:018  Type20[1]->End = 0xFFFFFF, Type17[2] = 0x6000
16:083  0:018  Table 131 is present, CPUType=31
16:102  0:018  Change to: 705
16:121  0:018  RSDT 0xC862D028
16:140  0:018  FADT from RSDT: 0xC862D110
16:161  0:021  XSDT 0xC862D080
16:180  0:018  FADT from XSDT: 0xC863B630
16:198  0:018  Xsdt reallocation done
16:231  0:032  old FADT length=10C
16:250  0:018  Found OperationRegion(GNVS, SystemMemory, C887EC18, ...)
16:269  0:018  Found OperationRegion(MCHT, SystemMemory, FED10000, ...)
16:288  0:018  Found OperationRegion(RCRB, SystemMemory, FED1C000, ...)
16:306  0:018  Found OperationRegion(XHCP, SystemMemory, 0, ...)
16:325  0:018  Found OperationRegion(MCA1, SystemMemory, F7FE0000, ...)
16:347  0:021  Found OperationRegion(MCA1, SystemMemory, F7FE0000, ...)
16:365  0:018  Found OperationRegion(CPSB, SystemMemory, C8626E18, ...)
16:384  0:018  Found OperationRegion(MBAR, SystemMemory, 0, ...)
16:403  0:018  Found OperationRegion(RAMW, SystemMemory, C8869018, ...)
16:422  0:018  Found OperationRegion(TMMB, SystemMemory, FED40000, ...)
16:463  0:041  DSDT len = 0xE493 new len = 0x10125
16:501  0:037  Apply DsdtFixMask=0x00000000 old way
16:519  0:018     drop _DSM mask=0xFFFF
16:538  0:018  ========= Auto patch DSDT Starting ========
16:560  0:021  VideoCard devID=0x100410DE
16:578  0:018  DisplayADR1[0] = 0x10000, DisplayADR2[0] = 0x0
16:597  0:018  Display 0 is  notPCIE
16:616  0:018  USBADR[0] = 0x140000 and PCIe = 0xFFFE
16:634  0:018  USBADR[1] = 0x1A0000 and PCIe = 0xFFFE
16:759  0:124  Found Airport BCM at 0x1C0004, 0x0
16:778  0:018  USBADR[2] = 0x1D0000 and PCIe = 0xFFFE
16:797  0:018  first CPU found at 84C8 offset 84CC
16:816  0:018  score candidate at 84C4
16:834  0:018  score inserted in acpi_cpu_score _PR_
16:855  0:021  Found ACPI CPU: CPU0 And CPU1 And CPU2 And CPU3 And CPU4 And CPU5 And CPU6 And CPU7 
  within the score: _PR_
17:025  0:169  Found PCIROOTUID = 0
17:043  0:018  ========= Auto patch DSDT Finished ========
17:062  0:018  Patch table: SSDT  Cpu0Ist
17:081  0:018   SSDT len = 0x539
17:100  0:018  Patch table: SSDT  CpuPm
17:118  0:018   SSDT len = 0xAD8
17:137  0:018  Patch table: SSDT  SataTabl
17:156  0:018   SSDT len = 0x36D
17:175  0:018  Patch table: SSDT  SaSsdt 
17:196  0:021   SSDT len = 0x34E1
17:215  0:018  Drop tables from Xsdt, SIGN=XXXX TableID= Length=0
17:233  0:018   Xsdt has tables count=11 
17:252  0:018  corrected XSDT length=124
17:271  0:018  Inserting SSDT.aml from EFI\CLOVER\OEM\MAXIMUS VI GENE\UEFI\ACPI\patched ... Success
17:311  0:039   CPUBase=0 and ApicCPUBase=1 ApicCPUNum=8
17:330  0:018  Maximum control=23
17:349  0:018  Turbo control=27
17:367  0:018  P-States: min 0x8, max 0x27
17:386  0:018  SSDT with CPU P-States generated successfully
17:425  0:038  SSDT with CPU C-States generated successfully
17:444  0:018  EdidDiscovered size=256
17:477  0:032  NVidia GFX injection not set
17:496  0:018  HDA Controller [8086:0C0C] :: PciRoot(0x0)\Pci(0x3,0x0) => codec not detected
17:640  0:143  LAN Controller [8086:153B] :: PciRoot(0x0)\Pci(0x19,0x0)
17:659  0:018  HDA Controller [8086:8C20] :: PciRoot(0x0)\Pci(0x1B,0x0) => codec not detected
17:802  0:143  stringlength = 860
17:821  0:018  CurrentMode: Width=2560 Height=1440
17:843  0:021  FSInjection: skipping kext injection (not requested)
17:900  0:057  MSR 0x1B0   set to        00000000
17:919  0:018  SetStartupDiskVolume:
17:937  0:018    * Volume: 'Macintosh SSD'
17:956  0:018    * LoaderPath: '<null string>'
17:975  0:018    * DevPath: Macintosh SSD
17:994  0:018    * GUID = 5F539792-05C0-418B-8E42-873972467708
18:012  0:018    * efi-boot-device: <array><dict><key>IOMatch</key><dict><key>IOProviderClass</key><string>IOMedia</string><key>IOPropertyMatch</key><dict><key>UUID</key><string>5F539792-05C0-418B-8E42-873972467708</string></dict></dict></dict></array>
18:034  0:021  Closing log
0:100  0:100  MemLog inited, TSC freq: 3499999031
0:100  0:000  
0:100  0:000  Now is 17.6.2014,  18:18:19 (GMT+2047)
0:100  0:000  Starting Clover rev 2721 on American Megatrends EFI
0:100  0:000  SelfDevicePath=PciRoot(0x0)\Pci(0x1D,0x0)\USB(0x1,0x0)\USB(0x2,0x0)\HD(1,GPT,EDE86EB9-A484-43B1-A598-E9E5A946C833,0x800,0x392000) @C5ECE498
0:100  0:000  SelfDirPath = \EFI\BOOT
0:103  0:002  UnicodeCollation Status=Success
0:103  0:000  Total Memory Slots Count = 4
0:103  0:000  Type 17 Index = 0
0:103  0:000  SmbiosTable.Type17->Speed = 1600
0:103  0:000  SmbiosTable.Type17->Size = 8192
0:103  0:000  Type 17 Index = 1
0:103  0:000  SmbiosTable.Type17->Speed = 1600
0:103  0:000  SmbiosTable.Type17->Size = 8192
0:103  0:000  Type 17 Index = 2
0:103  0:000  Ignoring insane frequency value 0MHz
0:103  0:000  SmbiosTable.Type17->Speed = 0
0:103  0:000  SmbiosTable.Type17->Size = 0
0:103  0:000  Type 17 Index = 3
0:103  0:000  Ignoring insane frequency value 0MHz
0:103  0:000  SmbiosTable.Type17->Speed = 0
0:103  0:000  SmbiosTable.Type17->Size = 0
0:103  0:000  Boot status=0
0:103  0:000  Clover revision: 2721  running on All Series
0:103  0:000  ... with board MAXIMUS VI GENE
0:103  0:000  Clover load options size = 4 bytes
0:128  0:025  Using OEM config.plist at path: EFI\CLOVER\OEM\MAXIMUS VI GENE\UEFI\config.plist
0:128  0:000  EFI\CLOVER\OEM\MAXIMUS VI GENE\UEFI\config.plist loaded: Success
0:135  0:006  Loading early settings
0:135  0:000  timeout set to 5
0:135  0:000  Default theme: Mavs Style
0:719  0:584  LoadDrivers() start
0:745  0:025  Loading FSInject-64.efi
0:771  0:026  Loading OsxFatBinaryDrv-64.efi
0:793  0:022  Loading VBoxHfs-64.efi
0:820  0:026   - driver needs connecting
0:836  0:016  Loading EmuVariableUefi-64.efi
0:864  0:028  EmuVariableUefi Initialize: VariableCommonInitialize = Success, orig services stored, install gEmuVariableControlProtocolGuid = Success
0:940  0:075  Loading OsxAptioFixDrv-64.efi
0:965  0:024  1 drivers needs connecting ...
0:984  0:019  PlatformDriverOverrideProtocol not found. Installing ... Success
1:021  0:037  Searching for invalid DiskIo BY_DRIVER connects: not found, all ok
1:174  0:152  LoadDrivers() end
1:191  0:017  EmuVariable InstallEmulation: orig vars copied, emu.var.services installed, CreateEvent VirtualAddressChange = Success, CreateEvent ExitBootServices = Success, set Status=Success
1:313  0:121  SetMaxResolution: found best mode 0: 2560x1440 - already set
1:371  0:057  Console modes reported: 4, available modes:
1:388  0:017    Mode 1: 80x25 (current mode)
1:408  0:020    Mode 2: 80x50
1:425  0:017    Mode 3: 100x31
1:446  0:020    Mode 4: 320x75
1:463  0:017  reinit: self device path=PciRoot(0x0)\Pci(0x1D,0x0)\USB(0x1,0x0)\USB(0x2,0x0)\HD(1,GPT,EDE86EB9-A484-43B1-A598-E9E5A946C833,0x800,0x392000)
1:483  0:020  new SelfHandle=C5ECE498
1:504  0:020  CPU Vendor = 756E6547 Model=306C3
2:592  1:088  The CPU supported turbo
2:609  0:016  BrandString = Intel(R) Core(TM) i7-4770K CPU @ 3.50GHz
2:629  0:019  MSR 0xE2 before patch 00000000
2:646  0:016  MSR 0xE4              00000000
2:666  0:019  MSR 0xCE              00080838_F3012300
2:683  0:016  non-usable FLEX_RATIO = F0000
2:702  0:019  corrected FLEX_RATIO = E0000
2:719  0:016  MSR 0x1B0             00000000
2:739  0:019  FSBFrequency=100MHz
2:756  0:016  Corrected FSBFrequency=100MHz
2:775  0:019  Vendor/Model/Stepping: 0x756E6547/0x3C/0x3
2:795  0:019  Family/ExtFamily: 0x6/0x0
2:815  0:019  MaxDiv/MinDiv: 35.0/8
2:831  0:016  Turbo: 39/39/39/39
2:851  0:019  Features: 0xBFEBFBFF
2:868  0:016  Threads: 8
2:888  0:019  Cores: 4
2:905  0:016  FSB: 100 MHz
2:925  0:019  CPU: 3503 MHz
2:941  0:016  TSC: 3503 MHz
2:961  0:019  PIS: 400 MHz
2:978  0:016  PCI (00|00:00.00) : 8086 0C00 class=060000
3:016  0:037  PCI (00|00:01.00) : 8086 0C01 class=060400
3:032  0:016  PCI (00|01:00.00) : 10DE 1004 class=030000
3:055  0:022  Found NVidia model=nVidia GeForce GTX 780
3:072  0:016  PCI (00|01:00.01) : 10DE 0E1A class=040300
3:092  0:019  PCI (00|00:02.00) : 8086 0412 class=038000
3:109  0:016  PCI (00|00:03.00) : 8086 0C0C class=040300
3:129  0:019  PCI (00|00:14.00) : 8086 8C31 class=0C0330
3:145  0:016  PCI (00|00:16.00) : 8086 8C3A class=078000
3:165  0:019  PCI (00|00:16.01) : FFFF FFFF class=FFFFFF
3:182  0:016  PCI (00|00:19.00) : 8086 153B class=020000
3:202  0:020  PCI (00|00:1A.00) : 8086 8C2D class=0C0320
3:222  0:019  PCI (00|00:1B.00) : 8086 8C20 class=040300
3:242  0:019  PCI (00|00:1C.00) : 8086 8C10 class=060400
3:259  0:016  PCI (00|00:1C.03) : 8086 8C16 class=060400
3:278  0:019  PCI (00|03:00.00) : 1B21 0612 class=010601
3:295  0:016  PCI (00|00:1C.04) : 8086 8C18 class=060400
3:315  0:019  PCI (00|04:00.00) : 14E4 43A0 class=028000
3:332  0:016  PCI (00|00:1D.00) : 8086 8C26 class=0C0320
3:352  0:019  PCI (00|00:1F.00) : 8086 8C44 class=060100
3:369  0:016  PCI (00|00:1F.03) : 8086 8C22 class=0C0500
3:392  0:022  PCI (00|00:1F.06) : FFFF FFFF class=FFFFFF
3:408  0:016  ScanSPD() start
3:429  0:020  SMBus CmdReg: 0x3
3:445  0:016  Scanning SMBus [8086:8C22], mmio: 0xF7C39004, ioport: 0xF040, hostc: 0x1
3:480  0:034  SPD[0]: Type 11 @0x50 
3:505  0:025  Using XMP Profile1 instead of standard frequency 1333MHz
3:525  0:019  DDR speed 1600MHz 
3:542  0:016  Slot: 0 Type 24 8192MB 1600MHz Vendor=Crucial Technology PartNo=BLT8G3D1608ET3LX0. SerialNo=0A09000408060A03 
3:579  0:036  SPD[1]: Type 11 @0x51 
3:604  0:025  Using XMP Profile1 instead of standard frequency 1333MHz
3:624  0:020  DDR speed 1600MHz 
3:642  0:018  Slot: 1 Type 24 8192MB 1600MHz Vendor=Crucial Technology PartNo=BLT8G3D1608ET3LX0. SerialNo=0A09000408070105 
3:795  0:152  ScanSPD() end
3:812  0:016  Get Acpi Tables List from RSDT:
3:849  0:036   Found table: FACP  A M I len=132
3:869  0:020   Found table: APIC  A M I len=146
3:886  0:017   Found table: FPDT  A M I len=68
3:906  0:019   Found table: LPIT  A M I len=92
3:928  0:022   Found table: SSDT  Cpu0Ist len=1337
3:947  0:018   Found table: SSDT  CpuPm len=2776
3:965  0:018   Found table: MCFG  A M I len=60
3:983  0:018   Found table: HPET  A M I len=56
4:001  0:018   Found table: SSDT  SataTabl len=877
4:020  0:018   Found table: SSDT  SaSsdt  len=13537
4:038  0:018   Found table: BGRT  A M I len=56
4:056  0:018  Calibrated TSC frequency =3499999031 =3499MHz
4:074  0:018  Loading main settings
4:093  0:018  KextsToPatch: 1 requested
4:114  0:020  KextToPatch 0: AppleTyMCEDriver Kext bin patch, data len: 24
4:186  0:072  Oem smbios.plist not found at path: EFI\CLOVER\OEM\MAXIMUS VI GENE\UEFI\smbios.plist
4:205  0:018  smbios.plist not found, not overriding config.plist
4:223  0:018  found 6 volumes with blockIO
4:241  0:018   0. Volume:
4:259  0:018    PciRoot(0x0)\Pci(0x1D,0x0)\USB(0x1,0x0)\USB(0x2,0x0)
4:295  0:035    USB volume
4:313  0:018    USB volume
4:331  0:018    Volume 'Whole Disc Boot', LegacyOS '', LegacyIcon(s) 'legacy', GUID = <null guid>
4:366  0:034   1. Volume:
4:384  0:018    PciRoot(0x0)\Pci(0x1D,0x0)\USB(0x1,0x0)\USB(0x2,0x0)\HD(1,GPT,EDE86EB9-A484-43B1-A598-E9E5A946C833,0x800,0x392000)
4:407  0:023    Result of bootcode detection: bootable <null string> (<null string>)
4:423  0:015    USB volume
4:441  0:018    USB volume
4:465  0:023    Volume 'BOOTER', LegacyOS '', LegacyIcon(s) '<null string>', GUID = EDE86EB9-A484-43B1-A598-E9E5A946C833
4:480  0:015    This is SelfVolume !!
4:498  0:018   2. Volume:
4:519  0:020    PciRoot(0x0)\Pci(0x1C,0x3)\Pci(0x0,0x0)\Sata(0x1,0xFFFF,0x0)
4:816  0:297    Volume 'Whole Disc Boot', LegacyOS '', LegacyIcon(s) 'legacy', GUID = <null guid>
4:835  0:018   3. Volume:
4:853  0:018    PciRoot(0x0)\Pci(0x1C,0x3)\Pci(0x0,0x0)\Sata(0x1,0xFFFF,0x0)\HD(1,GPT,F6FC26D9-7296-4388-BC41-9F1C43BBC31E,0x28,0x64000)
4:872  0:018    Result of bootcode detection: bootable <null string> (<null string>)
4:895  0:023    Volume 'EFI', LegacyOS '', LegacyIcon(s) '<null string>', GUID = F6FC26D9-7296-4388-BC41-9F1C43BBC31E
4:916  0:020   4. Volume:
4:935  0:018    PciRoot(0x0)\Pci(0x1C,0x3)\Pci(0x0,0x0)\Sata(0x1,0xFFFF,0x0)\HD(2,GPT,5F539792-05C0-418B-8E42-873972467708,0x64028,0x3B847340)
4:953  0:018    Volume 'Macintosh SSD', LegacyOS '', LegacyIcon(s) '<null string>', GUID = 5F539792-05C0-418B-8E42-873972467708
4:972  0:018   5. Volume:
4:990  0:018    PciRoot(0x0)\Pci(0x1C,0x3)\Pci(0x0,0x0)\Sata(0x1,0xFFFF,0x0)\HD(3,GPT,D6356AA1-D7E8-42BB-AFAA-9CD232C29C7A,0x3B8AB368,0x135F20)
5:011  0:021    Volume 'Recovery HD', LegacyOS '', LegacyIcon(s) '<null string>', GUID = D6356AA1-D7E8-42BB-AFAA-9CD232C29C7A
5:029  0:018  Searching volumes for latest nvram.plist ...
5:066  0:036    1. Volume 'BOOTER', GUID = EDE86EB9-A484-43B1-A598-E9E5A946C833 - no nvram.plist - skipping!
5:102  0:036    3. Volume 'EFI', GUID = F6FC26D9-7296-4388-BC41-9F1C43BBC31E - no nvram.plist - skipping!
5:139  0:036    4. Volume 'Macintosh SSD', GUID = 5F539792-05C0-418B-8E42-873972467708 - no nvram.plist - skipping!
5:181  0:042    5. Volume 'Recovery HD', GUID = D6356AA1-D7E8-42BB-AFAA-9CD232C29C7A - no nvram.plist - skipping!
5:218  0:036   nvram.plist not found!
5:236  0:018  PutNvramPlistToRtVars: nvram.plist not found
5:254  0:018  Invalidating BuiltinIcons...
5:273  0:018  no themes available, using embedded
5:291  0:018  Font 0 prepared WxH=7x12 CharWidth=7
5:309  0:018  Choosing theme <null string>
5:328  0:018  Custom entries start
5:346  0:018  Custom entries finish
5:364  0:018  Scanning loaders...
5:385  0:020   0: 'Whole Disc Boot' no file system
5:421  0:036   1: 'BOOTER'
5:740  0:318  skipped because path `PciRoot(0x0)\Pci(0x1D,0x0)\USB(0x1,0x0)\USB(0x2,0x0)\HD(1,GPT,EDE86EB9-A484-43B1-A598-E9E5A946C833,0x800,0x392000)\EFI\BOOT\BOOTX64.efi` is self path!
5:758  0:018   2: 'Whole Disc Boot' no file system
5:794  0:036   3: 'EFI'
5:831  0:036   4: 'Macintosh SSD'
5:872  0:041  Check if volume Is Hibernated:
5:891  0:018  Check sleep image 'by signature':
5:915  0:024  read prefs \Library\Preferences\SystemConfiguration\com.apple.PowerManagement.plist status=Not Found
5:954  0:038  using default sleep image name = \private\var\vm\sleepimage
5:976  0:022  Reading first 512 bytes of sleepimage ...
5:995  0:018   OurBlockIoRead: Lba=1AE41D8, Offset=35C83B000 (BlockSize=512)
6:013  0:018   sig lion: 0
6:031  0:018   sig snow: 0
6:050  0:018   no valid sleep image offset was found
6:068  0:018  Reading completed -> Success
6:086  0:018   sleepimage offset could not be acquired
6:107  0:020   hibernated: no - sign
6:128  0:020  found PciRoot(0x0)\Pci(0x1C,0x3)\Pci(0x0,0x0)\Sata(0x1,0xFFFF,0x0)\HD(2,GPT,5F539792-05C0-418B-8E42-873972467708,0x64028,0x3B847340)\System\Library\CoreServices\boot.efi
6:148  0:019   5: 'Recovery HD'
6:188  0:040  found PciRoot(0x0)\Pci(0x1C,0x3)\Pci(0x0,0x0)\Sata(0x1,0xFFFF,0x0)\HD(3,GPT,D6356AA1-D7E8-42BB-AFAA-9CD232C29C7A,0x3B8AB368,0x135F20)\com.apple.recovery.boot\boot.efi
6:207  0:019  Custom legacy start
6:226  0:018  Custom legacy end
6:244  0:018  Scanning legacy ...
6:279  0:034   0: 'Whole Disc Boot' (legacy) not legacy
6:315  0:036   1: 'BOOTER' (<null string>) not legacy
6:352  0:036   2: 'Whole Disc Boot' (legacy) not legacy
6:389  0:036   3: 'EFI' (<null string>) not legacy
6:425  0:036   4: 'Macintosh SSD' (<null string>) not legacy
6:462  0:036   5: 'Recovery HD' (<null string>) not legacy
6:499  0:036  Custom tool start
6:517  0:018  Custom tool end
6:545  0:028  found tool \EFI\CLOVER\tools\Shell64U.efi
6:562  0:017  Checking EFI partition Volume 3 for Clover
6:584  0:021  EmuVariable InstallEmulation: EFI_ALREADY_STARTED
6:621  0:036  GetEfiBootDeviceFromNvram:
6:659  0:037   efi-boot-device-data: PciRoot(0x0)\Pci(0x1C,0x3)\Pci(0x0,0x0)\Sata(0x1,0xFFFF,0x0)\HD(2,GPT,5F539792-05C0-418B-8E42-873972467708,0x64028,0x3B847340)
6:677  0:018   Volume: 'PciRoot(0x0)\Pci(0x1C,0x3)\Pci(0x0,0x0)\Sata(0x1,0xFFFF,0x0)\HD(2,GPT,5F539792-05C0-418B-8E42-873972467708,0x64028,0x3B847340)'
6:695  0:018   LoaderPath: '<null string>'
6:716  0:020   Guid = 5F539792-05C0-418B-8E42-873972467708
6:734  0:018   volume: partition = PciRoot(0x0)\Pci(0x1C,0x3)\Pci(0x0,0x0)\Sata(0x1,0xFFFF,0x0)\HD(2,GPT,5F539792-05C0-418B-8E42-873972467708,0x64028,0x3B847340)
6:753  0:018   searching for that partition
6:771  0:018    found entry 0. 'Boot Mac OS X from Macintosh SSD', Volume 'Macintosh SSD'
6:789  0:018  Boot redirected to Entry 0. 'Boot Mac OS X from Macintosh SSD'
6:808  0:018  EmuVariable UninstallEmulation: CloseEvent = Success, original var services restored
6:865  0:057  DefaultIndex=0 and MainMenu.EntryCount=7
6:901  0:035  Found Mouse device:
6:920  0:018  GUI ready
9:361  2:440  StartLoader() start
9:379  0:018  Finally: Bus=99999kHz CPU=3499MHz
9:398  0:018  Loading boot.efi
9:500  0:101  EmuVariable InstallEmulation: orig vars copied, emu.var.services installed, CreateEvent VirtualAddressChange = Success, CreateEvent ExitBootServices = Success, set Status=Success
9:633  0:133  insert table 9 for dev 0:0
9:651  0:018  insert table 9 for dev 19:0
9:672  0:020  insert table 9 for dev 0:0
9:691  0:018  Trusting SMBIOS...
9:709  0:018  Channels: 2
9:727  0:018  Interleave: 0 2 1 3 4 6 5 7 8 10 9 11 12 14 13 15 16 18 17 19 20 22 21 23
10:489  0:761   partNum=BLT8G3D1608ET3LX0.
10:507  0:018  SMBIOS Type 17 Index = 0 => 0 0:
10:526  0:018   DIMM1 1600MHz 8192MB
10:545  0:018  mTotalSystemMemory = 8192
10:564  0:018  SMBIOS Type 17 Index = 1 => 2 2:
10:583  0:018   DIMM2 EMPTY
10:602  0:018   partNum=BLT8G3D1608ET3LX0.
10:623  0:021  SMBIOS Type 17 Index = 2 => 1 1:
10:642  0:018   DIMM3 1600MHz 8192MB
10:661  0:018  mTotalSystemMemory = 16384
10:680  0:018  SMBIOS Type 17 Index = 3 => 3 3:
10:699  0:018   DIMM4 EMPTY
10:717  0:018  NumberOfMemoryDevices = 4
10:736  0:018  Type20[0]->End = 0x7FFFFF, Type17[0] = 0x2000
10:755  0:018  Type20[1]->End = 0xFFFFFF, Type17[2] = 0x6000
10:774  0:018  Table 131 is present, CPUType=31
10:793  0:018  Change to: 705
10:812  0:018  RSDT 0xC862D028
10:831  0:018  FADT from RSDT: 0xC862D110
10:854  0:022  XSDT 0xC862D080
10:874  0:020  FADT from XSDT: 0xC863B630
10:891  0:017  Xsdt reallocation done
10:911  0:020  old FADT length=10C
10:929  0:017  Found OperationRegion(GNVS, SystemMemory, C887EC18, ...)
11:242  0:313  Found OperationRegion(MCHT, SystemMemory, FED10000, ...)
11:260  0:017  Found OperationRegion(RCRB, SystemMemory, FED1C000, ...)
11:280  0:020  Found OperationRegion(XHCP, SystemMemory, 0, ...)
11:298  0:017  Found OperationRegion(MCA1, SystemMemory, F7FE0000, ...)
11:321  0:023  Found OperationRegion(MCA1, SystemMemory, F7FE0000, ...)
11:338  0:017  Found OperationRegion(CPSB, SystemMemory, C8626E18, ...)
11:359  0:020  Found OperationRegion(MBAR, SystemMemory, 0, ...)
11:376  0:017  Found OperationRegion(RAMW, SystemMemory, C8869018, ...)
11:397  0:020  Found OperationRegion(TMMB, SystemMemory, FED40000, ...)
11:439  0:041  DSDT len = 0xE493 new len = 0x10125
11:475  0:036  Apply DsdtFixMask=0x00000000 old way
11:496  0:020     drop _DSM mask=0xFFFF
11:533  0:036  ========= Auto patch DSDT Starting ========
11:553  0:020  VideoCard devID=0x100410DE
11:570  0:017  DisplayADR1[0] = 0x10000, DisplayADR2[0] = 0x0
11:591  0:020  Display 0 is  notPCIE
11:609  0:017  USBADR[0] = 0x140000 and PCIe = 0xFFFE
11:629  0:020  USBADR[1] = 0x1A0000 and PCIe = 0xFFFE
11:753  0:124  Found Airport BCM at 0x1C0004, 0x0
11:774  0:020  USBADR[2] = 0x1D0000 and PCIe = 0xFFFE
11:791  0:017  first CPU found at 84C8 offset 84CC
11:812  0:020  score candidate at 84C4
11:832  0:020  score inserted in acpi_cpu_score _PR_
11:853  0:020  Found ACPI CPU: CPU0 And CPU1 And CPU2 And CPU3 And CPU4 And CPU5 And CPU6 And CPU7 
  within the score: _PR_
12:022  0:169  Found PCIROOTUID = 0
12:043  0:020  ========= Auto patch DSDT Finished ========
12:061  0:017  Patch table: SSDT  Cpu0Ist
12:081  0:020   SSDT len = 0x539
12:099  0:017  Patch table: SSDT  CpuPm
12:119  0:020   SSDT len = 0xAD8
12:137  0:017  Patch table: SSDT  SataTabl
12:157  0:020   SSDT len = 0x36D
12:177  0:020  Patch table: SSDT  SaSsdt 
12:198  0:020   SSDT len = 0x34E1
12:215  0:017  Drop tables from Xsdt, SIGN=XXXX TableID= Length=0
12:236  0:020   Xsdt has tables count=11 
12:253  0:017  corrected XSDT length=124
12:274  0:020  Inserting SSDT.aml from EFI\CLOVER\OEM\MAXIMUS VI GENE\UEFI\ACPI\patched ... Success
12:317  0:043   CPUBase=0 and ApicCPUBase=1 ApicCPUNum=8
12:334  0:017  Maximum control=23
12:355  0:020  Turbo control=27
12:373  0:017  P-States: min 0x8, max 0x27
12:393  0:020  SSDT with CPU P-States generated successfully
12:413  0:020  SSDT with CPU C-States generated successfully
12:434  0:020  EdidDiscovered size=256
12:451  0:017  NVidia GFX injection not set
12:472  0:020  HDA Controller [8086:0C0C] :: PciRoot(0x0)\Pci(0x3,0x0) => codec not detected
12:633  0:161  LAN Controller [8086:153B] :: PciRoot(0x0)\Pci(0x19,0x0)
12:651  0:017  HDA Controller [8086:8C20] :: PciRoot(0x0)\Pci(0x1B,0x0) => codec not detected
12:796  0:144  stringlength = 860
12:816  0:020  CurrentMode: Width=2560 Height=1440
12:836  0:020  FSInjection: skipping kext injection (not requested)
12:895  0:059  MSR 0x1B0   set to        00000000
12:913  0:017  SetStartupDiskVolume:
12:934  0:020    * Volume: 'Macintosh SSD'
12:951  0:017    * LoaderPath: '<null string>'
12:972  0:020    * DevPath: Macintosh SSD
12:989  0:017    * GUID = 5F539792-05C0-418B-8E42-873972467708
13:010  0:020    * efi-boot-device: <array><dict><key>IOMatch</key><dict><key>IOProviderClass</key><string>IOMedia</string><key>IOPropertyMatch</key><dict><key>UUID</key><string>5F539792-05C0-418B-8E42-873972467708</string></dict></dict></dict></array>
13:030  0:020  Closing log
 

Still not booting...

Share this post


Link to post
Share on other sites

Hi all,

have here 10.9.3 with latest clover Version on an DELL M6300, installation and boot in Marvericks is OK but without LAN / Audio.

The interesting thing is that everything works with chameleon, even if i start with a clover USB Boot Stick in a chameleon installation HD (first chameleon test HD).

But with a fresh clover installation (second clover test HD) and the same kext from chameleon installtion will LAN / Audio not work.

 

i have this in org.chameleon.Boot.plist.

 

    <key>EthernetBuiltIn</key>
    <string>Yes</string>

    <key>PciRoot</key>
    <string>1</string>

    <string>Yes</string>
    <key>device-properties</key>
  <string>4b00000001000000010000003f0000000100000002010c00d041030a0000000001010600051c0101060000007fff0400160000006200750069006c0074002d0069006e0000000500000001</string>
 

device-properties is for the NIC

 

 

this kext use i with chameleon / clover:

 

ACPIBatteryManager.kext

FakeSMC.kext

VoodooPS2Controller.kext

AppleHDADisabler.kext

Patched_10.7_AppleRTC.kext

VoodooSDHC.kext
BCM5722D.kext

VoodooHDA.kext

lspcidrv.kext

 

Wath missing here in clover ?

Need any help here with this Problem.

thx

 

parcival

Share this post


Link to post
Share on other sites

Hi all,

have here 10.9.3 with latest clover Version on an DELL M6300, installation and boot in Marvericks is OK but without LAN / Audio.

The interesting thing is that everything works with chameleon, even if i start with a clover USB Boot Stick in a chameleon installation HD (first chameleon test HD).

But with a fresh clover installation (second clover test HD) and the same kext from chameleon installtion will LAN / Audio not work.

 

i have this in org.chameleon.Boot.plist.

 

    EthernetBuiltIn

    Yes

    PciRoot

    1

    Yes

    device-properties

  4b00000001000000010000003f0000000100000002010c00d041030a0000000001010600051c0101060000007fff0400160000006200750069006c0074002d0069006e0000000500000001

 

device-properties is for the NIC

 

 

this kext use i with chameleon / clover:

 

ACPIBatteryManager.kext

FakeSMC.kext

VoodooPS2Controller.kext

AppleHDADisabler.kext

Patched_10.7_AppleRTC.kext

VoodooSDHC.kext

BCM5722D.kext

VoodooHDA.kext

lspcidrv.kext

 

Wath missing here in clover ?

Need any help here with this Problem.

thx

 

parcival

These kexts:

BCM5722D.kext

VoodooHDA.kext

are used on my computer #3 and they are not required any patches from Clover.

@Fab1Man

Still panic on AppleTyMCEDriver? May be erase it?

Share this post


Link to post
Share on other sites

These kexts:

BCM5722D.kext

VoodooHDA.kext

are used on my computer #3 and they are not required any patches from Clover.

@Fab1Man

Still panic on AppleTyMCEDriver? May be erase it?

 

privjet Slice, thanks for your answer.

Where did you store the kext? S/L/E or EFI

The interesting thing for me is that it works with a clover boot tick. (myHack chameleon HD).

It is possibly the myHack.kext located in S/L/E why it works.

Can you please show your clover config?

Share this post


Link to post
Share on other sites

These kexts:

BCM5722D.kext

VoodooHDA.kext

are used on my computer #3 and they are not required any patches from Clover.

@Fab1Man

Still panic on AppleTyMCEDriver? May be erase it?

Yes, still panic. When I remove my SMBIOS entry in config.plist, and therefore also this patch, no KP, but still no boot either.

What I think is strange is that from an upgrade 10.9.3 --> 10.10 with working DSDT and SSDT, FakeSMC in /S/L/E it didn't KP at AppleTyMCEDriver.

Share this post


Link to post
Share on other sites

..i'm struggling with my Clover installation.

Can anyone with a GA Z-77-D3H Mobo help me out with the right configuration.

My GPU is an nVidia 210.

This is where the booting stops.

 

IMG_1090.jpg

 

Thanks

Share this post


Link to post
Share on other sites

These kexts:

BCM5722D.kext

VoodooHDA.kext

are used on my computer #3 and they are not required any patches from Clover.

@Fab1Man

Still panic on AppleTyMCEDriver? May be erase it?

 

smal update,

if i put all kext in S/L/E then LAN / Audio works.

But why will clover not load all the same kext from EFI ?

May you be loaded too soon from EFI.

If i remember correctly with changing the plist key "root" in the kext, but not sure.

Share this post


Link to post
Share on other sites

LAN kext has dependency on IONetworkFamily.kext as well as AUDIO kext has dependency on IOAudioFamily.kext.

If we load a kext from EFI we must be sure dependency is loaded too.

Or just place all kexts into SLE as I did.

Or boot WithoutCache as Chameleon did.

Share this post


Link to post
Share on other sites

Hi Slice,

is there a solution for boot hangs on: AppleTyMCEDriver::start coreVIDPID......... that is with Clover patch for AppleTyMCEDriver.kext. Why does it hang on that line ?. Without patch it just KP. 

Share this post


Link to post
Share on other sites

..i'm struggling with my Clover installation.

Can anyone with a GA Z-77-D3H Mobo help me out with the right configuration.

My GPU is an nVidia 210.

This is where the booting stops.

 

 

Thanks

 

Try booting in "single user" mode. Also, try adding -x (for booting into Safe Mode) in Clover options.

 

To add boot flags, load up Clover (from your USB drive if you haven't installed the OS already) and go to Clover Options (should be somewhere on the second row of icons). In there, look for Boot Flags, press Enter to be able to write, then enter "-x" (without quotes, obviously) and press Enter again to save. Then go back (there should be a return option somewhere on that screen).

After that, go to your Yosemite USB drive, and press the spacebar. You should see a little menu. From there, select Single User mode.

 

You should see a lot of text. When it's done loading all that wall of text, type "exit" and press Enter. In theory that's all you need to trick it into loading the installer (again,assuming you haven't installed the OS already).

 

Good luck.

Share this post


Link to post
Share on other sites

Regarding my problem, it's booting. However, not the way I want.

I've used an old DSDT I once made, put that in patched, BOOM works. The problem with this DSDT is, that every trigger of a sound event results in an instant freeze and then crash.

Share this post


Link to post
Share on other sites

Clover breaking sound on AppleHDA patched! about Yosemite and Mavericks!
This does not happen on Chamelion bootloader, sound is perfect!
Any solution about Clover for correct loading AppleHDA patched?

Share this post


Link to post
Share on other sites

Clover breaking sound on AppleHDA patched! about Yosemite and Mavericks!

This does not happen on Chamelion bootloader, sound is perfect!

Any solution about Clover for correct loading AppleHDA patched?

Are you using the same OS in this comparison?

In theory, Clover doesn't break anything related to the OS. It's a bootloader. But that kext you're trying might be dependent on something that Chameleon adds in its Extra folder. In my opinion, Clover has less chances than Chameleon to break anything.

 

Have you tried using VoodooHDA (2.8.5) instead?

 

If you're trying to use the same kext from Mavericks, I suggest you not to do it, or at least, ensure that your kext has been updated to work with Yosemite.

I for one, couldn't get the patched AppleHDA kext to work with Yosemite + Clover. And I didn't need to do it in Mavericks since for that case, I'm using Chameleon and ALC892kext (which doesn't seem to work in Yosemite).

Share this post


Link to post
Share on other sites

Hi Slice,

is there a solution for boot hangs on: AppleTyMCEDriver::start coreVIDPID......... that is with Clover patch for AppleTyMCEDriver.kext. Why does it hang on that line ?. Without patch it just KP. 

Sorry guys, I have no solutions for you, I may just propose something.

There are numerous discussions about this kext AppleTyMCE and no any proved result. For my disassembling the kext is still the same and the patch must work. If not - see your own mistake.

You can erase this kext.

You can don't use MacPro4,1 and MacPro5,1 personality. Hackintosh works fine with iMac personality.

Share this post


Link to post
Share on other sites

Are you using the same OS in this comparison?

In theory, Clover doesn't break anything related to the OS. It's a bootloader. But that kext you're trying might be dependent on something that Chameleon adds in its Extra folder. In my opinion, Clover has less chances than Chameleon to break anything.

 

Have you tried using VoodooHDA (2.8.5) instead?

 

If you're trying to use the same kext from Mavericks, I suggest you not to do it, or at least, ensure that your kext has been updated to work with Yosemite.

I for one, couldn't get the patched AppleHDA kext to work with Yosemite + Clover. And I didn't need to do it in Mavericks since for that case, I'm using Chameleon and ALC892kext (which doesn't seem to work in Yosemite).

AppleHDA be loaded and run on Clover but sound is broken and sound have popcorn!

AppleHDA be patched on the OS Caribe; (Yosemite and Maviricks)

Chamelion load OS X system does not break AppleHDA sound and no sound popcorn!

 

Clover be doing something about the systems. config.plist not have anything about injection only sound audio = Detect

Share this post


Link to post
Share on other sites

AppleHDA be loaded and run on Clover but sound is broken and sound have popcorn!

AppleHDA be patched on the OS Caribe; (Yosemite and Maviricks)

Chamelion load OS X system does not break AppleHDA sound and no sound popcorn!

 

Clover be doing something about the systems. config.plist not have anything about injection only sound audio = Detect

Pop up sond you can using this  simple Installer  and reboot after 

 

Works perfect for me   see my  Haswell specs  

Share this post


Link to post
Share on other sites

Thanks Slice for response.

I do delete AppleTyMCED and have flawless hack with Macpro 5,1 definition.

Just wanted a solution that would allow me to install osx without deleting or changing anything other than appleHDA.

Thanks anyway.  :thumbsup_anim: .

 

to others...mu boot time with clover with SSD and legacy boot to desktop is under 8 sec. so it is faster for me than the chameleon.

Share this post


Link to post
Share on other sites

Thanks Slice for response.

I do delete AppleTyMCED and have flawless hack with Macpro 5,1 definition.

Just wanted a solution that would allow me to install osx without deleting or changing anything other than appleHDA.

Thanks anyway.  :thumbsup_anim: .

 

to others...mu boot time with clover with SSD and legacy boot to desktop is under 8 sec. so it is faster for me than the chameleon.

You may install OS with iMac personality and after deleting this kext change to MacPro wink_anim.gif

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   1 member

  • Similar Content

    • By rtke333
      Acer Aspire V15 V5-591G - Mojave 10.14.4
       
      (Note: mine is 55TU version, but the bootpack will work fine with another versions of 591G, for example: V5-591G-71K2, -764Z, -59PU, etc.)
      Specifications:
      - Motherboard: USOPP_SLS (Skylake-H PCH)
      - BIOS:Insyde Corp. v 1.15
      - CPU:Intel Core i5-6300HQ 2.3 GHz (Skylake)
      - GPU: NVIDIA GeForce GTX 950M 2 GB (Optimus) & Intel HD Graphics 530
      - RAM:SK hynix 4 GB DDR4 (Later I bought + KINGSTON 4 GB) 2133 MHz
      - WiFi + Bluetooth:Qualcomm Atheros QCNFA344A 5 GHz (Later -> Broadcom BRCM94352Z M.2 5 GHz WiFi + 4.0 Bluetooth)
      - Audio:Realtek HD Audio: ALC 255 
      - Ethernet: Realtek RTL8168/8111
      - Card Reader:Realtek USB 2.0 Card Reader (USB2.0-CRW)
      - Webcam:HD Webcam
      - HDD:TOSHIBA MQ01ACF032 320 GB HDD
      - SSD:SPCC M.2 230 GB SSD
      - Display:1366x768 (15.6", Matte)
      - Battery: 6 cell 56Wh / 5040mAh
      - Connectors: 
      1x SD Card Reader 2x USB 3.0 (1x USB Charging), 1x USB 2.0 1x VGA 1x HDMI 1x 3.5mm microphone/audio combined jack connector 1x Ethernet (Rj-45) - Keyboard & Touchpad:Multi-Touch & Multi-gestures ELAN 501 Touchpad, Backlight Keyboard.
      Working:  
      - Wi-Fi (with BCM94352Z)
      - Bluetooth hand-off (With BCM94352Z)
      -Full Graphics enabled on HD 530: ig-platform-id: 0x191b0000 (HD 530 Mobile)
      - Display: if default colour profile is corrupted (blue is not actual blue but purplish) Use "Rec. ITU-R BT. 709-5" Color Profile (System Pref. -> Displays -> Color)
      -HDMI & VGA Outputs: AppleGraphicsDevicePolicy.kext Clover patch
      - Audio (ALC 255):(Internal Speakers, Internal Microphone, Headphone jack with AppleALC, ALCPlugFix -> layout-id=17)
      - Ethernet Realtek 8168/8111: RealtekRTL8111.kext
      - App Store, Messages, FaceTime, Siri, iCloud(native)
      - Integrated webcam(native)
      - 3.0 USB (native)
      - Touchpad and Keyboard(ELAN501): Fn keys are good, the weird thing is the Brightness key. On my keyboard it's Pause Break:Br-up, Fn+F12:Br-dwn-> To fix this try Karabiner (VoodoPS2Controller.kext), - for gestures try SmartTouchpad drivers
      - Battery info:Install ACPIBatteryManager.kext with Kext Utility or other installer.
      - Sleep Mode
      - SSD with TRIM enabled (to enable trim, open Terminal and write "sudo trimforce enable")
      Not working:
      - Original Wi-Fi (Qualcomm Atheros QCNFA344A):  unsupported, you need switch to BCM94352Z or just use a mini usb wifi dongle.
      - NVIDIA GeForce GTX 950M: Optimus not supported.
      - Card Reader: Unsupported -> Can't really fix because I don't have any SD Card at the moment, maybe can be fixed by adding Prod & Ven IDs to AppleStorageDevices.kext, I never used it anyway. name: "USB2.0-CRW" Prod ID: "0x0129" Ven ID: "0x0bda  (Realtek Semiconductor Corp.)"
      For Wi-Fi:
      - 1st method:You can choose an external USB wifi dongle (I used TP-Link Archer T1U (5GHz support), TP-Link has official macOS drivers, you just need to install it
      -2nd and I think the best method:Replace your M.2 Qualcomm Card with a compatible BCM94352Zcard (you will have hand-off Bluetooth too), just install the kexts (enabled with BrcmFirmwareData.kext, BrcmPatchRAM2.kext, FakePCIID.kext, FakePCIID_Broadcom_WiFi.kext, they're all in my attached zip). You could buy this card from ebay, aliexpress, or amazon
       
      Issues:
      - None
      BIOS Settings:
      - BIOS version 1.15 (irrelevant)
      - Secure Boot: Disabled
      - Touchpad: Advanced
      - Boot mode:UEFI
      Getting ready for Installation:
      - Download the install zip (bootpack & postinstall): Click here -> acer_aspire_v591g_installfiles.zip
      Installation:
      - Create an installer with any method you know (- Mac: createinstallmedia - Windows: Transmac, Vmware, Win32diskimager)
      - Copy my Clover folder to the USB's EFI folder
      - Boot with the Installer USB
      - If you stuck in boot, reboot and in the Clover bootloader select "config_debug.cfg" -> you'll have more informations about the freeze
       
      Please open the README.rtf in my install zip for more informations about the USB Installer & Post installation!
      If you have a single RAM and getting panic at boot, then you need to edit the "config.plist" with these (SMBIOS->after "Version 1.0"):
      ->Edit "Frequency" and "Size" to match your RAM values
      <key>Version</key> <string>1.0</string> <key>Memory</key> <dict> <key>Channels</key> <integer>1</integer> <key>SlotCount</key> <integer>1</integer> <key>Modules</key> <array> <dict> <key>Slot</key> <integer>0</integer> <key>Size</key> <integer>8192</integer> <key>Frequency</key> <integer>2133</integer> <key>Type</key> <string>DDR4</string> </dict> </array> </dict> </dict>  
      PowerManagement  fix:
      Set HWPEnable=YES in Clover (already set), CPUFloor to "700", Frequency to "2300" and "3200"(Normal and Turbo, if you have i7-6700HQ version then it should be "2600", "3500") and "FrequencyVectors" from "0x0d000000" to "0x07000000" in "S/L/E/IOPlatformPluginFamily.kext/Contents/PlugIns/X86PlatformPlugin.kext/Contents/Resources/Mac-A5C67F76ED83108C.plist", MSR _xcpm_idle Patch to KernelToPatch in Clover (If you have High Sierra, change "MatchOS" to 10.13):

      <key>KernelToPatch</key> <array> <dict> <key>Comment</key> <string>MSR 0xE2 _xcpm_idle instant reboot(c) Pike R. Alpha</string> <key>Disabled</key> <false/> <key>Find</key> <data> ILniAAAADzA= </data> <key>MatchOS</key> <string>10.14</string> <key>Replace</key> <data> ILniAAAAkJA= </data> </dict> </array> Reboot, and it's 800MHz in idle state, same on Windows.
       

       
      Before updating to a new version of Mojave please update kexts (and clover if necessary) to newer versions to avoid kernel panics.
      Generate a serial number with Clover Configurator.app (open up your config.plist with CC then -> SMBIOS -> Serial Number -> Generate New)
      Mojave & Windows 10 Dual-Boot:
      Dual-boot clean install (on one drive), UEFI Only:
       
       Boot into your Mac installer, Create 2 partitions in GUID table (1 for Win (I used FAT32 but I think it doesn't matter what you choose), 1 for Mac),   Install Mac, boot with your USB, mount your EFI partition (use terminal or an EFI mounter app), create an EFI folder (if there is no folder), copy the CLOVER folder I attached to the EFI folder, restart,  Boot into your Win installer, Format the partition you created for Win, install.   Now, it's automatically booting into Windows. To use Clover open cmd in administrator, type:  bcdedit /set {bootmgr} path \EFI\CLOVER\CLOVERX64.efi       5.  You're done! It will booting into Clover when you start the system, and you can select Win or Mac (or another OS if installed on a 3rd partition).
       
      Dual-boot with Windows installed first (on one drive), UEFI Only:
      If you already have Windows and you don't want to lose all your data there is a hope:
      I created a video from this restore method: [Hackintosh] Dual-Boot High Sierra & Windows - when Windows already installed - no data waste - UEFI
      You need bootable Mac Installer and a full system restore image (link is in my video's description).
      (You may see errors if your EFI partition is not 200 MB)
       Boot into your Windows, resize your partition or create one for Mac.  Boot into your Mac installer and in Disk Utility format the partition you created.  Restore from image: select your full system restore image.  When it's finished restoring you just need to restart, then boot to the system with your usb.  When you successfully booted to Mac desktop, mount your EFI partition (use terminal or an EFI mounter app), open EFI, you will see there is a Microsoft folder already (don't touch that!). Copy my CLOVER folder to the EFI folder then Restart.  Now, it's automatically booting into Windows. To use Clover open cmd in administrator, type:  bcdedit /set {bootmgr} path \EFI\CLOVER\CLOVERX64.efi       7.  You're done! You can select your old Windows and your new macOS!
      (Only tried with Windows 8/8.1/10. I don't know Windows 7,etc.)
       
      IF YOU GETTING ERRORS DURING MAC RESTORE:
      - Make sure you have partitions in GPT
      - Windows using 100 MB EFI and will annoy the Mac restore. Don't worry, just ignore the errors.
       
      IF YOU GETTING ERRORS DURING WINDOWS INSTALLATION (could not be formatted, etc):
      - Make sure you have GPT partitions, and GPT (UEFI) installer, also disconnect all external storage drives (except the installer USB)
       
      IF YOU USED RESTORE METHOD THEN CAN'T MOUNT YOUR EFI PARTITION (No EFI partition found):
      - It's because your EFI is not 200 MB or not an "Apple" original EFI,  but do not worry, try another EFI mounter, or mount from terminal (I used EFI mounter v3: Getting errors, but you can mount and use without problem)
      - You also could "mount" the EFI from Windows:
      1st method: open cmd in administrator mode and type:
      diskpart
      list vol (Now select the "System" volume,(FAT 32) For example I select 4)
      sel vol 4
      list part(Select System type partition, for example 2)
      sel part 2
      assign letter=b(This will "mount" your EFI partition)
      Open Explorer++ or TotalCommander in administrator mode to manage EFI
      remove letter=b (This will "unmount" your EFI)
      2nd method: open cmd in administrator mode and type:
      mountvol b: /s (This will mount your EFI)
      Open Explorer++ or TotalCommander in administrator mode to manage EFI
      mountvol b: /d (This will unmount your EFI)
      Thanks to all OSXLatitude members for helping me out! (Jake Lo, Hervé, Bronxteck, black.dragon74)!
      Notes:
      2019.03.30: Fixed USB 3.0 ports, fixed Bluetooth crashes after sleep -> updated bootpack
      2019.03.28: Updated to 10.14.4. Unexpected crashes while updating to 10.14.4 -> fixed by updating Clover to the latest (v4910) version. Bluetooth crashes appeared -> fixed by downgraded Brcm*.kexts. Updated bootpack.
      2019.02.24: Bluetooth crashes after sleep -> fixed, updated bootpack. 
      2019.02.22: Updated to 10.14.3. Fixed HDMI Audio by installing "FakePCIID_Intel_HDMI_Audio.kext" -> fixed freezing during boot. Fixed brightness levels by installing "AppleBacklightFixup.kext". Also updated bootpack & postinstall zip down in attachments.
      2019.01.21: Removed FakeSMC.kext, SMCHelper-64.efi, replaced by VirtualSMC.kext, VirtualSMC.efi because I got random freezes when booting system (kextd stall[0], (120s): 'AppleACPICPU' -> CPU is at 100%, fans are spinning fast), also updated bootpack in the attachments "acer_aspire_v591g-55tu_clover.zip"-> Freeze continued, brought back FakeSMC, deleted VirtualSMC (caused BT crashes).
      2019.01.18: HDMI Audio is fixed, I didn't do anything HDMI Audio is not fixed, sometimes it worked but most likely not. (no idea why)
      2018.12.09: Updated to 10.14.2 -> did without any complication
      2018.11.28: Fixed combo-jack garbage sound output by installing ALCPlugFix and CodecCommander.kext
      2018.11.01: Updated to 10.14.1 -> HDMI & VGA ports are gone again. -> Fixed by "AppleIntelSKLGraphicsFramebuffer.kext" rollback from 10.14.
      2018.09.28: Updated to Mojave 10.14 -> Fixed HDMI & VGA Outputs by adding "AppleGraphicsDevicePolicy.kext" patches to config.plist, HDMI audio not working
    • By ciriousjoker
      TLDR:
      I'm trying to boot MacOS on a Chromebook without UEFI. I'm stuck at getting the bootloader (Chameleon/Clover) to work.  
      My setup / context:
      I have an Acer Chromebook Spin 13.
      Available ports:
      2 x USB-C 1 x USB-A 3.0 MicroSD Slot No USB A 2.0 (I've read that Clover has problems with USB 3.0) Firmware:
      There's no UEFI firmware available and by default, it doesn't even allow booting anything other than ChromeOS. Thanks to MrChromebox (big shoutouts!), I flashed a custom legacy bios that allows me to boot anything linux related. This bios is flashed into the RW_LEGACY section of the existing bootloader (coreboot afaik) and doesn't have any configuration options. If I have to change a setting, I could try compiling his bios payload myself with the specific setting enabled.  
      What I've tried so far:
      Chameleon attempts:
      Only selected setting was "Install chameleon on the chosen path", rest was unselected.
       
      1 - Install chameleon first without restoring the basesystem:
      Output:
      > boot0: GPT
      > boot0: done
      (hangs; pressing power button once shuts down
      Chameleon installation log is attached as "Chameleon_Installer_Log_BEFORE".
       
      2 - Install Chameleon after restoring the base system:
      Output:
      > boot0: GPT
      > boot0: GPT
      > boot0: doneboot1: /boot       <- Exactly like that, no line break in between
      (hangs; pressing power button once shuts down)
       
      I haven't been able to reproduce #2 after wiping the drive and doing the same thing again. Subsequent attempts have resulted in either #1 of either Chameleon or Clover.
      Chameleon installation log is attached as "Chameleon_Installer_Log_AFTER".
       
      Clover attempts:
      I tried multiple settings and configurations, but all of them boiled down to either one of these.
       
      1 - Doesn't do anything, just hangs at "Booting from usb..."
      2 - Boots into the blue/grey mode as shown in the attached images.
      According to MrChromebox, this could be an old Tianocore DUET It doesn't detect anything (cpu frequency, ram, partitions or disks)  
      I've read pretty much every article, github readme and other types of documentation for coreboot, tianocore, clover, chameleon and MrChromebox' rw_legacy payloads and right now, I'm totally clueless as to what to try next...
       
      A few questions that came up:
      Why does chameleon hang? What is it looking for, /boot was clearly written to the disk by the Chameleon installer? What exactly is the blue/grey image? According to MrChromebox, it could be Tianocore DUET Where does it come from? Clover? The mainboard itself? Why does the blue/grey thing not detect my processor frequency or any partitions/drives? Can I use some sort of DUET bootloader to chainload Clover?  
      If you guys could answer any of them or if you have any other guesses or information as to what's happening, I'd be really happy!
      Chameleon_Installer_Log_BEFORE.txt
      Chameleon_Installer_Log_AFTER.txt





    • By outdoormagic
      Short Version:
      I have two drives with the exact same EFI folder (and I can boot into Clover from either one), shouldn't I be able to boot into MacOS from either one?
       
      More Detail:
      I've done a few hacks so far and this never happened. (Gigabyte z370 / 8700k / Vega, Asus z390 / i5-9600k / 1080). Now, I'm setting up a ThinkPad X1 Gen 6. (Yes, I do expect problems on laptops, but that's not the question).
       
      Mojave 10.14.4 now boots from the internal SSD. So far, so good. Here's the problem.
       
      I installed Mojave on a USB drive (for backup / rescue) and copied the entire EFI partition of my boot drive to the EFI partition on the USB drive. So... I should be able to boot from the USB drive, right? Wrong. Ran Clover installer on the USB itself. Same outcome.
       
      With F12, I can boot from the USB into Clover and select the OS on the USB. The boot sequence hangs on End Random Seed, but before the usual '++++++++' line.
      So, boot into Clover on internal boot drive, then select OS on USB. Same thing.
       
      Read the forums, I saw the posts about AptioMemoryFix, so I tried the various other drivers on the USB. No go.
       
      I haven't found the solution yet to the USB boot issue, but what puzzles me is that if I have two drives with the exact same EFI folder (and I can boot into Clover from either one), shouldn't I be able to boot into MacOS from either one?
       
       
×