Jump to content
ErmaC

Clover General discussion

23,144 posts in this topic

Recommended Posts

Advertisement

well i have everything working 100% now and last thing was edit my Config to 

 

boot the main drive after 3 seconds with injected kexts loaded... did what i thought was that and now i can see the drive... i know i have done a little bit wrong and can't figure out where -

 

 

config.plist.zip

Share this post


Link to post
Share on other sites

Hi guys, i found two things on GUI with I believe it isnt a normal behavior:

 

1) on Clover GUI -> Options -> CPU enable C6 is checked, but I didnt check this parameter on config.plist, in fact I use piker ssdtgen so I didnt check any CPU parameters on clover besides dropSSDT  and only enableC6 is checked on that panel. i dont know from where this value is read but it is not from config.plist neither nvram (list using nvram -p)

 

2) when I boot from pendrive (UEFI) I can see Clover options on GUI with I can add Clover entry to BIOS BOOT, but when i boot from disk (also UEFI), this option is not available. I didnt find any option on config.plist with allow enable Clover Options from disk, and i use the same config.plist from pendrive.

 

I hope it helps the development of clover.

Share this post


Link to post
Share on other sites

You turned off the scan for entries to boot

	<key>GUI</key>
	<dict>
		<key>Scan</key>
		<dict>
			<key>Entries</key>
			<false/>
			<key>Legacy</key>
			<false/>
			<key>Tool</key>
			<true/>
		</dict>

Set GUI/Scan/Entries=true.

 

thanks you... was half asleep last night post 2 nights at a stag do and then starting the build...

 

very much appreciated... 

Share this post


Link to post
Share on other sites

Hello scott_donald

 

Take a look here post 20 : http://www.insanelymac.com/forum/topic/295549-clover-config/

 

Fabio

 wow that is awesome...

 

currently have a nice fresh install on my test drive...

 

see there is 3 with the z87 asus boards....

 

fabio1971... dont suppose i can get your SSDT's.... or your efi to try on the test drive... was going to upgrade to 10.9.3 and see how it goes before doing it on my ssd.... 

Share this post


Link to post
Share on other sites

I would like to enter a discussion on this community's use of Clover boot loader. What have you all found out about loading and using Clover? Have you all used fdisk440 to help build your bootable USB? Did you all find the Installation.txt file in Clover?

 

What has everyone done to get Clover to load MacOS X (be it Snow Leopard, Lion, Mountain Lion or Mavericks.)

Share this post


Link to post
Share on other sites

Hey all!

 

So I've been running Mac OS X Mavericks and Windows 8.1 together for a while now using Clover.

However through no fault other than my own I messed up my EFI during an upgrade/repair of Windows.

I mananged to get Clover up and running for booting Windows in UEFI again by copying the approriate /EFI/Microsoft/Boot files.

However Mac OS X just goes to a blank screen. Running it with -x -v gives:

 

Error allocationg 0x28 pages at [some hex at ff1000] alloc type 2

Could not locate driver module memoryBoot failed, sleeping for 10 seconds before exiting.

 

I can boot into the Mac OS X partition with a boot USB (again using -x, since the audio driver is in shambles), tried reinstalling Clover; but alas, no avail. 

The annoying bit is that I can't manually inspect the EFI partition in safe mode, since the Fat32 driver doesn't get loaded.

 

Any thoughts?

 

PS: For what it's worth: it's a Asus P8Z77-M Pro motherboard with a Intel Xeon E3-1240 V2 and 32GB RAM

Share this post


Link to post
Share on other sites

slide=0?

 

If you are using VBoxHFS.efi change it by HFSPlus.efi that can be downloaded from "Clover Instruction" named FSDrivers.zip

Share this post


Link to post
Share on other sites

Error allocationg 0x28 pages at [some hex at ff1000] alloc type 2

Could not locate driver module memoryBoot failed, sleeping for 10 seconds before exiting.

 

Okay, I feel moderately ashamed for admitting this but what happened is the following:

I messed up my EFI partition (ESP) somehow; I got Windows 8.1 to boot but not OS X Mavericks.

 

Using a USB Boot stick I tried reinstalling and messing with the various Clover options. Unfortunately I had to do so in safe mode, due to other reasons.

Save mode does, however, not allow access to Fat32 or NTFS. So when reinstalling and/or trying different drivers I did so in the designated /EFI/ Folder of the boot drive (instead of the partition).

Now the shameful element is: I kept booting from the broken EFI partition (which I was unable to access) being equivalent to questions like "are you sure you're editing the right file?" … which after an extended period of frustration always has to be answered with "ah no, you see ...".

 

Booting from the correct EFI configuration (which worked perfectly for OS X) allowed me to fix the partition (yay read/write support for Fat32) throw out all the other stuff and now everything works fine again. Lesson learned. Thanks everyone! :rolleyes:

Share this post


Link to post
Share on other sites
Hi, I have two small problems with my set-up AsRock X79 Professional with E5-1620 v2; 
 
-Speedstep problem; with ssdtPRGen I rarely have x12, x37 always (standard clock) and occasionally turbo x38 (but the processor has turbo x39). 
With Clover (GenStates + DropOEM) I often have x12 and normally x37, never turbo. I also have an error: "Failed C-state...". (Attached Image)
 
-USB problem, I know Mac OS don't like my TI USB3 chipset, I'm using GenericUSB kext or clover patch (for 10.9.3 doesn't work well), but I have problem with USB 2, bluetooth mouse not received well, it's slow, same thing for the keyboard.
Never had any problems with Gigabyte and Fresco chipset. Has anyone ever had similar problems? (Not only with bluetooth, also with device)

Thanks.
Simone

post-1086468-0-86444300-1400770408_thumb.png

Share this post


Link to post
Share on other sites

 

Hi, I have two small problems with my set-up AsRock X79 Professional with E5-1620 v2; 
 
-Speedstep problem; with ssdtPRGen I rarely have x12, x37 always (standard clock) and occasionally turbo x38 (but the processor has turbo x39). 
With Clover (GenStates + DropOEM) I often have x12 and normally x37, never turbo. I also have an error: "Failed C-state...". (Attached Image)
 
-USB problem, I know Mac OS don't like my TI USB3 chipset, I'm using GenericUSB kext or clover patch (for 10.9.3 doesn't work well), but I have problem with USB 2, bluetooth mouse not received well, it's slow, same thing for the keyboard.

Never had any problems with Gigabyte and Fresco chipset. Has anyone ever had similar problems? (Not only with bluetooth, also with device)

 

Thanks.

Simone

 

Make a report with DarwinDumper for better see your problem.

Share this post


Link to post
Share on other sites

Hi, I have two small problems with my set-up AsRock X79 Professional with E5-1620 v2; 

 

-Speedstep problem; with ssdtPRGen I rarely have x12, x37 always (standard clock) and occasionally turbo x38 (but the processor has turbo x39). 

With Clover (GenStates + DropOEM) I often have x12 and normally x37, never turbo. I also have an error: "Failed C-state...". (Attached Image)

 

-USB problem, I know Mac OS don't like my TI USB3 chipset, I'm using GenericUSB kext or clover patch (for 10.9.3 doesn't work well), but I have problem with USB 2, bluetooth mouse not received well, it's slow, same thing for the keyboard.

Never had any problems with Gigabyte and Fresco chipset. Has anyone ever had similar problems? (Not only with bluetooth, also with device)

Thanks.

Simone

Your cpu a ivy brige ?

Share this post


Link to post
Share on other sites

Hi !

 

I have successfully installed Mavericks with Clover on a Dell Inspiron 1720, after trying without success with Chameleon. (At first I had freezing problems with Clover that were related to a faulty HDD)

 

My WiFi card is never recognised although it works natively with Leopard.

 

The WiFi card is an Atheros branded Gigabyte GN-WI01GT (Ven_168C Dev_001C) existing in the Info.plist of the Atheros plugin.

 

Apprently the card is seen in the profiler but I read it in reverse. (maybe I'm missing something)

    | |   |   +-o PXS2@0  <class IOPCIDevice, id 0x1000001ca, registered, matched, active, busy 0 (215 ms), retain 12>
    | |   |       {
    | |   |         "assigned-addresses" = <10000c82000000000000fff90000000000000100>
    | |   |         "IOPCIPMCSState" = 0x0
    | |   |         "IOInterruptSpecifiers" = (<1100000007000000>,<0300000000000100>)
    | |   |         "class-code" = <00000200>
    | |   |         "IODeviceMemory" = (({"address"=0xf9ff0000,"length"=0x10000}))
    | |   |         "built-in" = <00>
    | |   |         "subsystem-vendor-id" = <58140000>
    | |   |         "IOPowerManagement" = {"MaxPowerState"=0x3,"ChildProxyPowerState"=0x2,"CurrentPowerState"=0x2}
    | |   |         "pci-aspm-default" = 0x3
    | |   |         "acpi-device" = "IOACPIPlatformDevice is not serializable"
    | |   |         "IOInterruptControllers" = ("io-apic-0","IOPCIMessagedInterruptController")
    | |   |         "name" = <65746865726e657400>
    | |   |         "IOChildIndex" = 0x1
    | |   |         "device-id" = <1c000000>
    | |   |         "vendor-id" = <8c160000>
    | |   |         "IOPCIResourced" = Yes
    | |   |         "compatible" = <706369313435382c6539313300706369313638632c316300706369636c6173732c303230303030005058533200>
    | |   |         "IOPCIExpressLinkCapabilities" = 0x33c11
    | |   |         "acpi-path" = "IOACPIPlane:/_SB/PCI0/RP02@1c0001/PXS2@0"
    | |   |         "subsystem-id" = <13e90000>
    | |   |         "revision-id" = <01000000>
    | |   |         "IOPCIExpressLinkStatus" = 0x1011
    | |   |         "IOPCIExpressCapabilities" = 0x11
    | |   |         "pcidebug" = "12:0:0"
    | |   |         "IOName" = "ethernet"
    | |   |         "device_type" = <65746865726e657400>

    | |   |         "reg" = <00000c000000000000000000000000000000000010000c0200000000000000000000000000000100>
    | |   |         "acpi-wake-type" = 0x2
    | |   |       }

Device is PXS2 but there is "device-id" = <1c000000> and "vendor-id" = <8c160000>.

 

The WiFi  LED is on and it works under Windows, but in System Profiler it doesn't appear in WiFi.

 

Anyway, does the Chameleon argument "Max_valid_dma_addr=1024" exists in Clover ?

Share this post


Link to post
Share on other sites

Hi !

 

I have successfully installed Mavericks with Clover on a Dell Inspiron 1720, after trying without success with Chameleon. (At first I had freezing problems with Clover that were related to a faulty HDD)

 

My WiFi card is never recognised although it works natively with Leopard.

 

The WiFi card is an Atheros branded Gigabyte GN-WI01GT (Ven_168C Dev_001C) existing in the Info.plist of the Atheros plugin.

 

Apprently the card is seen in the profiler but I read it in reverse. (maybe I'm missing something)

    | |   |   +-o PXS2@0  <class IOPCIDevice, id 0x1000001ca, registered, matched, active, busy 0 (215 ms), retain 12>
    | |   |       {
    | |   |         "assigned-addresses" = <10000c82000000000000fff90000000000000100>
    | |   |         "IOPCIPMCSState" = 0x0
    | |   |         "IOInterruptSpecifiers" = (<1100000007000000>,<0300000000000100>)
    | |   |         "class-code" = <00000200>
    | |   |         "IODeviceMemory" = (({"address"=0xf9ff0000,"length"=0x10000}))
    | |   |         "built-in" = <00>
    | |   |         "subsystem-vendor-id" = <58140000>
    | |   |         "IOPowerManagement" = {"MaxPowerState"=0x3,"ChildProxyPowerState"=0x2,"CurrentPowerState"=0x2}
    | |   |         "pci-aspm-default" = 0x3
    | |   |         "acpi-device" = "IOACPIPlatformDevice is not serializable"
    | |   |         "IOInterruptControllers" = ("io-apic-0","IOPCIMessagedInterruptController")
    | |   |         "name" = <65746865726e657400>
    | |   |         "IOChildIndex" = 0x1
    | |   |         "device-id" = <1c000000>
    | |   |         "vendor-id" = <8c160000>
    | |   |         "IOPCIResourced" = Yes
    | |   |         "compatible" = <706369313435382c6539313300706369313638632c316300706369636c6173732c303230303030005058533200>
    | |   |         "IOPCIExpressLinkCapabilities" = 0x33c11
    | |   |         "acpi-path" = "IOACPIPlane:/_SB/PCI0/RP02@1c0001/PXS2@0"
    | |   |         "subsystem-id" = <13e90000>
    | |   |         "revision-id" = <01000000>
    | |   |         "IOPCIExpressLinkStatus" = 0x1011
    | |   |         "IOPCIExpressCapabilities" = 0x11
    | |   |         "pcidebug" = "12:0:0"
    | |   |         "IOName" = "ethernet"
    | |   |         "device_type" = <65746865726e657400>

    | |   |         "reg" = <00000c000000000000000000000000000000000010000c0200000000000000000000000000000100>
    | |   |         "acpi-wake-type" = 0x2
    | |   |       }

Device is PXS2 but there is "device-id" = and "vendor-id" = .

 

The WiFi  LED is on and it works under Windows, but in System Profiler it doesn't appear in WiFi.

 

Anyway, does the Chameleon argument "Max_valid_dma_addr=1024" exists in Clover ?

I think it is kernel flag and doesn't depend on bootloader.

Share this post


Link to post
Share on other sites

Anybody familiar with this problem? I tried several things, tried common solutions but nothing works. BIOS settings are correct.

It's a Z77X-UD5H board. Windows can be booted through Clover.

post-1125699-0-18431000-1400856831_thumb.jpg

Share this post


Link to post
Share on other sites

Anybody familiar with this problem? I tried several things, tried common solutions but nothing works. BIOS settings are correct.

It's a Z77X-UD5H board. Windows can be booted through Clover.

what drivers u install ?

u need aptiofix!

I write something about this board if u wanna read..

http://www.insanelymac.com/forum/topic/288829-guide-gigabyte-z77x-ud5h-clover-uefi-installtweak-guide/

? ...you joke ?

No joke.

u ask if its ivy i posted link where it says its ivy.

Why u say its joke ?

Share this post


Link to post
Share on other sites

 

Hi, I have two small problems with my set-up AsRock X79 Professional with E5-1620 v2; 
 
-Speedstep problem; with ssdtPRGen I rarely have x12, x37 always (standard clock) and occasionally turbo x38 (but the processor has turbo x39). 
With Clover (GenStates + DropOEM) I often have x12 and normally x37, never turbo. I also have an error: "Failed C-state...". (Attached Image)
 
-USB problem, I know Mac OS don't like my TI USB3 chipset, I'm using GenericUSB kext or clover patch (for 10.9.3 doesn't work well), but I have problem with USB 2, bluetooth mouse not received well, it's slow, same thing for the keyboard.

Never had any problems with Gigabyte and Fresco chipset. Has anyone ever had similar problems? (Not only with bluetooth, also with device)

 

Thanks.

Simone

 

 

Make a report with DarwinDumper for better see your problem.

- With Clover Gen. States http://www22.zippyshare.com/v/38557643/file.html

- With SSDT by Pike http://www57.zippyshare.com/v/65410067/file.html

- My CPU E5-1620v2 (same as MacPro 2013) is Ivy Bridge-EP LGA2011

 

Thank you Slice & Clover Staff!

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

Announcements

  • Similar Content

    • By MaLd0n
      -OpenCore Vanilla TUTORIAL-
       
       
      -USB Port Mapping TUTORIAL-
       
        1 -Create a USB bootable
       
      Create your usb installer, use this tool and download Catalina or Big Sur from Apple servers
       
      Catalina
      installScript_allfullapp.zip
       
      Big Sur
      installScript_1016fullapp.zip
       
      Credits: crazybirdy
       
      Copy Catalina / Big Sur installer to Applications folder, open terminal and run
       
      Catalina
       
       
      Big Sur
       
       
      If you want check one step by step, check here
       
      -Opencore Vanilla Tutorial
      https://tinyurl.com/ycvcnp8h
       
      2- EFI folder USB installation
       
      -EFI OpenCore Folder Desktop 10th Intel Processors
      Paste this EFI folder in EFI partition in your USB STICK
      https://tinyurl.com/ybwr9kq3
       
      -EFI Clover Folder Desktop 10th Intel Processors
      Paste this EFI folder in EFI partition in your USB STICK
      https://tinyurl.com/yxsw7d3t
       
      3- EFI folder SSD
       
      -EFI OpenCore Folder Desktop 10th Intel Processors
      Paste this EFI folder in EFI partition SSD 
      https://tinyurl.com/ybwr9kq3
       
      -EFI Clover Folder Desktop 10th Intel Processors
      Paste this EFI folder in EFI partition SSD
      https://tinyurl.com/yxsw7d3t
       
      4- Start Fine Tune
       
      Run this app and post full dump here for full ACPI solution
       
      RunMe.app
      https://tinyurl.com/y9562hz7
       
       
      If you like a SSDT way, here we go
      SSDT-OLARILA.aml.zip
       
      5- USB Solution
       
      Use these kexts, enable XHCI port limit patch
       
      USB INTEL SERIE 400.zip
       
      and follow this tutorial for remap USB ports
       
       
      --DSDT PATCHES--
       
      -FIX ERRORS AND WARNINGS -FIX ACPI ERRORS -REMOVE UNUSED SCOPES / DEVICES -HIGH PRECISION EVENT TIMER -SATA SERIE ID -DMAC -REMOVE LINES, PROBLEMATIC and UNUSED -FIX K.P in REBOOT -NVRAM -REAL TIME CLOCK -SLPB -DARWIN / WINDOWS -XHCI -PLUGIN TYPE -HDEF -ARTC -IPIC -TIMR -SBUS -BUS1 -MCHC -ALS0 -SHUTDOWN -UAR1 -LAN -FWHD -USBX -PMCR -PPMC -XSPI -kUSBCompanionIndex -io-device-location -IMEI -EC -PNLF -ARPT -GFX0 -NVME -ACPI-WAKE-GPE -DTGP -HDMI / HDAU  
      --SCREENSHOTS--































      -If you want to buy me a beer - Donations with PayPal
      https://tinyurl.com/r2bvzm7
       
      Big Thanks to XLR and your Badass Motherboard, Ultrafast CPU, Coolest Heatsink, Huge Graphics Card, Tonnes of RAM,
      Gigantic Hard Drive, Lightspeed Disk Burner, Professional Sound Card, Massive LCD Display.
       
       
      -Credits and thanks to the old and new people in the community who developed patches, kexts and bootloaders!
      Slice, Kabyl, usr-sse2, jadran, Blackosx, dmazar, STLVNUB, pcj, apianti, JrCs, pene, FrodoKenny, skoczy, ycr.ru, Oscar09, xsmile, SoThOr, RehabMan, Download-Fritz, Zenit432, cecekpawon, Intel, Apple, Oracle, Chameleon Team, crazybirdy, Mieze, Mirone, Oldnapalm, netkas, Elconiglio, artut-pt, ErmaC, Pavo, Toleda, Master Chief and family, bcc9, The King, PMheart, Sherlocks, Micky1979, vit9696, vandroiy2013, Voodoo Team, Pike R. Alpha, lvs1974, Austere.J, CVad and many, many, many others!

      We're all here to have fun and learn from each other!
    • By Nomade
      Hello All,
       
      It's been a while that I am trying to update my system to 10.15.16.
      The install seem to start, then at reboot time I only see the Normal boot and the Recovery option from the Clover boot menu.
      None of those 2 allow to complete the update.
       
      Is there any ways to force it to install and/or show the "Update" option on the Clover boot screen?
       
      PS: I'm using Z97-Gaming-3
    • By Damx
      The specs CPU: Intel® Core™ i3 Processor 8130U, 2.20 GHz (Kaby Lake Refresh) Chipset: Intel® 300 Series Graphics: Intel® UHD Graphics 620 Display: 21.5'' 1920x1200 RAM: DDR4 PC2400 4GB SSD1: M.2 PLEXTOR (with original Windows 10) SSD2: SATA SAMSUNG 850 EVO (for macOS) Sound: Realtek ALC269 WiFi / BT: Intel 3168 NGW Realtek Card-reader  
       
      Not working
      WiFi: Intel 3168 NGW Realtek Card-reader  
       
      Pre-Installation
       
      I will not go through the basics since it is explained in details here on this site. Briefly, the process is to:
      Get Clover Get Catalina macOS installer Create USB with 2 MBR partitions (FAT32 for Clover and HFS+J for the installer)  
       
      Required kexts
      AppleALC.kext Lilu.kext RealtekRTL8111.kext VirtualSMC.kext WhateverGreen.kext  
       
      Config.plist
      I used the one provided by RehabMan called config_HD615_620_630_640_650.plist. Download it from GitHub. It has almost everything you will need with only few edits for audio.
      Edits:
      [CPU] Make sure there is lilcpu=9 setting in boot arguments needed for Kaby Lake R CPU to be recognised correctly. [GPU] Make sure there is a patch GFX0 to IGPU under ACPI->DSDT [GPU] Under Devices->Properties->PciRoot(0)/Pci(0x02,0) make sure that the AAPL,ig-platform-id value is 00001B59, and the device-id value is 16590000 [AUDIO] Under Devices->Properties->PciRoot(0)/Pci(0x1f,3) set the layout-id to 40 and the device-id to 70A10000 [SMBIOS] Set Mac model ID is iMac19,2  

       

       
      Notes
      For some reason with latest version of Clover the install partition was not visible. If you run into the same issue you can downgrade Clover to r5103, which worked perfectly. WiFi / BT Intel 3168 NGW needs to be replaced if one needs WiFi. Someone mentioned that to get HDMI work properly you may need to change AAPL,ig-platform-id value to 00001659 for PciRoot(0)/Pci(0x02,0) - not my case but may be considered if you get this issue. Don't forget to generate your serial and other SMBUS values before signing in with iCloud services.  
       
    • By MaLd0n
      A very custom DSDT for best experience under macOS. Removed all unused devices, injected all Apple devices, essentials, cosmetics, real improvements. 
       
      -OpenCore Vanilla TUTORIAL-
       
       
      -USB Port Mapping TUTORIAL-
       
          -Original DSDT have 167,880 lines and 762kb
       
      DSDT ORIGINAL.aml.zip138.01 kB · 8 downloads
       
      -Patched DSDT have 30,912 lines and 111kb
       
      DSDT PATCHED.aml.zip27.01 kB · 17 downloads
       
      --Hardware--
      Asus ROG RAMPAGE VI EXTREME OMEGA

      Processor  Intel i9-10980XE

      GPU Radeon RX 5700 XT

      --DSDT Patches--
      -FIX ERRORS AND WARNINGS -FIX ACPI ERRORS -REMOVE UNUSED SCOPES / DEVICES -HIGH PRECISION EVENT TIMER -SATA SERIE ID -DMAC -REMOVE LINES, PROBLEMATIC and UNUSED -REAL TIME CLOCK -SLPB -DARWIN / WINDOWS -XHCI -PLUGIN TYPE -HDEF -ARTC -IPIC -TIMR -SBUS -BUS1 -MCHC -ALS0 -SHUTDOWN -UAR1 -LAN -FWHD -USBX -XSPI -EC -PNLF -ARPT -GFX0 -NVME  
      --Screenshots-



















       
      -Credits and thanks to the old and new people in the community who developed patches, kexts and bootloaders!
      Slice, Kabyl, usr-sse2, jadran, Blackosx, dmazar, STLVNUB, pcj, apianti, JrCs, pene, FrodoKenny, skoczy, ycr.ru, Oscar09, xsmile, SoThOr, RehabMan, Download-Fritz, Zenit432, cecekpawon, Intel, Apple, Oracle, Chameleon Team, crazybirdy, Mieze, Mirone, Oldnapalm, netkas, Elconiglio, artut-pt, ErmaC, Pavo, Toleda, Master Chief and family, bcc9, The King, PMheart, Sherlocks, Micky1979, vit9696, vandroiy2013, Voodoo Team, Pike R. Alpha, lvs1974, Austere.J, CVad and many, many, many others!

      We're all here to have fun and learn from each other!
    • By MaLd0n
      -OpenCore Vanilla TUTORIAL-
       
       
      -USB Port Mapping TUTORIAL-
       
          -Wifi card has been replaced with Dell DW1560!
      -I'm using a S145 Model with Intel Core i5-1035G1 IceLake / Intel HD Graphics ICL
      -Update bios/uefi to last version 
       
      *For now we have 2 problems. Wake from sleep and some bugs in trackpad*
       
      --Bios/UEFI config--
      Go to Security tab and disable Secure boot
       
      -IceLake Premade installation Folder (easy way installation)
      https://tinyurl.com/y3tl6xlx
       
      --Clover and OpenCore Folders--
      Just paste EFI folder inside EFI partition
      -OpenCore
      https://tinyurl.com/y3c4rjkr
      -Clover
      https://tinyurl.com/y4496nq8
       
      --Enable Trackpad Dragging Option--
      Go to System Preferences/Accessibility/PointerControl/Trackpad Options and "Enable dragging"

      -Bluetooth Broadcom
       
      BrcmBluetoothInjector.zip2.46 MB · 4 downloads
       
      -OcQuirks.efi for Clover (Just replace Drivers folder)
       
      drivers.zip74.57 kB · 4 downloads
       
      --DSDT Patches--

      -Patches
      -FIX ERRORS AND WARNINGS -REMOVE UNUSED SCOPES / DEVICES -HIGH PRECISION EVENT TIMER -SATA SERIE 12 ID -DMAC -REMOVE LINES, PROBLEMATIC and UNUSED -SLPB -DARWIN / WINDOWS 2015 -XHCI -PLUGIN TYPE -HDAS to HDEF -HDEF -REAL TIME CLOCK -ARTC -IRQs -SBUS -BUS1 -MCHC -ALS0 -SHUTDOWN -FWHD -USBX -PMCR -PPMC -XSPI -GMM -IMEI -EC -PRWs -_DSMs -PNLF -BRIGHTNESS KEYS -I2C -NATIVE USB -ARPT -GFX0 -DTGP -ACQUIRE MUT0 0XFFFF -OPERATION REGION GPIO -MUTEX MUT0 0x00 -EXTERNAL REFERENCES -UNKNOWNOBJ -FULL RENAMED DEVICES   --IGPU Patch-- (All credits to Austere.J) Discussion about that HERE
       
      <key>PciRoot(0x0)/Pci(0x2,0x0)</key>             <dict>                 <key>AAPL,ig-platform-id</key>                 <data>AABSig==</data>                 <key>device-id</key>                 <data>UooAAA==</data>                 <key>framebuffer-fbmem</key>                 <data>AACQAA==</data>                 <key>framebuffer-patch-enable</key>                 <data>AQAAAA==</data>                 <key>framebuffer-stolenmem</key>                 <data>AAAwAQ==</data>                 <key>framebuffer-unifiedmem</key>                 <data>AAAAgA==</data>                 <key>hda-gfx</key>                 <string>onboard-1</string>                 <key>igfxfw</key>                 <data>AgAAAA==</data>             </dict>  
      --USB Fix-- https://tinyurl.com/y4mqfahz
       
      -ScreenShots

       


























      -Credits and thanks to the old and new people in the community who developed patches, kexts and bootloaders!   Slice, Kabyl, usr-sse2, jadran, Blackosx, dmazar, STLVNUB, pcj, apianti, JrCs, pene, FrodoKenny, skoczy, ycr.ru, Oscar09, xsmile, SoThOr, RehabMan, Download-Fritz, Zenit432, cecekpawon, Intel, Apple, Oracle, Chameleon Team, crazybirdy, Mieze, Mirone, Oldnapalm, netkas, Elconiglio, artut-pt, ErmaC, Pavo, Toleda, Master Chief and family, bcc9, The King, PMheart, Sherlocks, Micky1979, vit9696, vandroiy2013, Voodoo Team, Pike R. Alpha, lvs1974, Austere.J, CVad, Sampath007, onemanosx, erroruser, Jenny David, Acidanthera Team, Olarila Facebook Community, Hackintosh Facebook Community and many others!     We're all here to have fun and learn from each other!
×