I'm not expecting too much help, but if anyone has any suggestions, that would be great.
I recently got my Hackintosh running on macOS 10.14, and went to install the graphics drivers for my Nvidia GeForce GTX 750 Ti. My setup is a little different, so here it is:
Screen 1 Screen 2 Screen 3
Screen 1 and 2 are both connected to my 750 Ti, whereas screen 3 is connected to my iGPU, with is an intel HD 4600. The intel GPU works like a charm, just as it did under High Sierra.
Now, I got the Nvidia Web drivers to "work" by removing any traces via the "Web Driver Toolkit" that others have recommended. I then patched the installer, installed it, rebooted, patched the installed drivers, and rebooted again, where the drivers are at their current state.
This is where things get interesting though. All 3 monitors are recognized. My GPU is recognized in my system profiler. However, it is NOT able to be used to run a compute in Geekbench, meaning that GPU acceleration is obviously disabled. The other thing that doesn't work, is, well, the 2 monitors connected to the GPU. They are set to the correct resolution and refresh rates, and are recognized in System Preferences, and I can even drag things between the different desktops.
But I can only see my cursor. The screens are totally black, and I can't see anything on them except my cursor moving across them. Has this happened to anyone else? Thanks in advance!
Specs: Asrock B85M-Pro4 Motherboard Intel Core i5-4690 CPU Intel HD 4600 GPU 1 Nvidia GeForce GTX 750 Ti GPU 2 iMac 15,1 SMBIOS
Here is a picture of what happens https://imgur.com/gallery/lWTLWlw
Hi, I tried during last 4 days almost everything but now I call for help. I have RX560 running on 10.13.4. Previously I was running it on 10.12.6 and had the same problem, but after waking from sleep my thiord display came to life, but it is not working anymore on 10.13.4. Without or with Lilu & Whatewergreen my system correctly recognize my gpu as RX560 but only 2 of 3 displays are displaying content, third display is black but recieving some signal. When I change cabling and connect only two, any combination of 2 displays is working. System profiller and system preferences are sayin I have 3 displays connected.
Please can somebody help me to figure it out? Thanks a lot in advance. Tried to upload my ioreg but it is greater than 10MB allowed for me :(
Hello! I have a problem installation UniBootX bootloader. When I tried start bootloader with pendrive I see only black screen. Any ideas? My config:
1.Toshiba Satellite U920T
2.Intel Core i5 3317u with SSE2, SSE3
4. Intel® HD Graphics 4000
5. Resolutons : 1366 x 768
6. Realtek High Definition Audio
7.Intel Centrino Wireless N 2230
8. No DVD
9. Dysk SSD 120GB AHCI one partition
10. Mouse USB 3.0
I recently set up my hackintosh. Everything else works fine, the only issue is my monitor cannot come back from sleep.
If I click the "sleep" menu manually, the system goes to sleep fine. After the system sleeps for a while (more than a few mins, I guess it's called "deep sleep"), when I try to wake it up, the monitor wakes up but stays black screen. The machine is on.
If I leave the system to time out and sleep by itself, only the monitor goes off; when I try to wake it up, same symptom as above.
What I have tried (but none worked):
additional boot flag: ngfxpatch=pikera
additional boot flag: darkwake = 0
Motherboard: Gigabyte Z77x-UD5H
CPU: Ivy Bridge i5-3570K CPU @ 3.40GHz (quad core)
Graphics: Nvidia GTX 1050
Monitor: Dell P2715Q @ 4k / 60Hz, Display Port
Wifi / Bluetooth: BCM94360CS with PCIE
Onboard GPU: disabled
OS: High Sierra 10.13.3
Please see attached for following files:
EFI zip file: https://www.dropbox.com/s/8nun37msu9b1bva/EFI.zip?dl=0
I generated my own SSDT.aml using ssdtPRGen.sh;
Other SSDT patches are copied from this repository: https://github.com/VoiletDragon/Z77X-UD5H-Clover-Hotpatch-Patches
ioreg dump: https://www.dropbox.com/s/5a10k82guczaaws/macchiato.ioreg.zip?dl=0
result from following command: https://www.dropbox.com/s/0b22qcw79ovnjdg/kext-touch.txt.zip?dl=0
kextstat|grep -y acpiplat
kextstat|grep -y appleintelcpu
kextstat|grep -y applelpc
kextstat|grep -y applehda
sudo touch /System/Library/Extensions && sudo kextcache -u /
I am looking forward to your suggestions. Thanks.